Académique Documents
Professionnel Documents
Culture Documents
created by sbabu on Nov 4, 2014 12:34 PM, last modified by panagent on Nov 14, 2014 12:40 PM
Overview
This document describes how to configure Routing Information Protocol (RIP) on a Palo Alto Networks device.
Example scenario:
Steps
1. Go to Network > Virtual Router and check default.
https://live.paloaltonetworks.com/docs/DOC-8277 Page 1 of 5
How to Configure RIP | Palo Alto Networks Live 4/19/15, 6:56 PM
3. Select the interface and check Enable and Advertise, as shown below.
https://live.paloaltonetworks.com/docs/DOC-8277 Page 2 of 5
How to Configure RIP | Palo Alto Networks Live 4/19/15, 6:56 PM
5. Follow the same steps for other Palo Alto Networks devices and check the neighbor state.
==========
virtual router: default
peer address: 13.0.0.1
last update: Wed Nov 5 01:52:54 2014
RIP version: 2
invalid packets: 0
invalid routes: 0
==========
virtual router: default
reject default route: yes
redist default route: block
interval seconds: 1
update intervals: 30
expire intervals: 180
delete intervals: 120
interface: 13.0.0.2
https://live.paloaltonetworks.com/docs/DOC-8277 Page 3 of 5
How to Configure RIP | Palo Alto Networks Live 4/19/15, 6:56 PM
==========
Flags: S:stale path, L:linked, P:programmed
destination metric tag flag path-detail
10.50.240.0/24 1 0 L RDIST connected route on ethernet1/1
10.50.240.0/24 2 0 LP RIP route, next hop 13.0.0.1, from peer 13.0.0.1,
age 26
10.50.241.0/24 2 0 LP RIP route, next hop 13.0.0.1, from peer 13.0.0.1,
age 26
10.50.242.0/24 1 0 L RDIST connected route on ethernet1/3
10.50.242.0/24 2 0 LP RIP route, next hop 13.0.0.1, from peer 13.0.0.1,
age 26
12.0.0.0/24 2 0 LP RIP route, next hop 13.0.0.1, from peer 13.0.0.1,
age 26
13.0.0.0/24 1 0 LP RIP connected route on ethernet1/6
13.0.0.0/24 1 0 L RDIST connected route on ethernet1/6
192.168.10.12/30 1 0 L RDIST route, next hop 192.168.10.12
192.168.10.16/30 1 0 L RDIST route, next hop 192.168.10.16
172.16.2.2/31 2 0 LP RIP route, next hop 13.0.0.1, from peer 13.0.0.1,
age 26
172.16.2.4/31 2 0 LP RIP route, next hop 13.0.0.1, from peer 13.0.0.1,
age 26
192.168.10.10/31 1 0 L RDIST route, next hop 192.168.10.10
192.168.10.20/32 1 0 L RDIST route, next hop 192.168.10.20
13.0.0.0/24 10 0 L RIP local route
https://live.paloaltonetworks.com/docs/DOC-8277 Page 4 of 5
How to Configure RIP | Palo Alto Networks Live 4/19/15, 6:56 PM
Note: Palo Alto Networks devices support only RIPv2. Auto-summarization of RIP routes is not supported.
owner: sbabu
362 Views Categories: Network Tags: routing, networking, rip, ripv2, virtual_routers
(3 ratings)
0 Comments
https://live.paloaltonetworks.com/docs/DOC-8277 Page 5 of 5