Académique Documents
Professionnel Documents
Culture Documents
AREA CLASSIFICATION
Energy
DOCUMENT NO : GEN-SPC-ELC-6610 REV. : B PAGE 1 of 10
362829727.doc
SPECIFICATION FOR ELECTRICAL Petro-
AREA CLASSIFICATION
Energy
DOCUMENT NO : GEN-SPC-ELC-6610 REV. : B PAGE 2 of 10
Revision Record Information:
362829727.doc
SPECIFICATION FOR ELECTRICAL Petro-
AREA CLASSIFICATION
Energy
DOCUMENT NO : GEN-SPC-ELC-6610 REV. : B PAGE 3 of 10
TABLE OF CONTENTS
1.0 SCOPE.............................................................................................................................. 4
4.0 DRAWINGS....................................................................................................................... 5
362829727.doc
SPECIFICATION FOR ELECTRICAL Petro-
AREA CLASSIFICATION
Energy
DOCUMENT NO : GEN-SPC-ELC-6610 REV. : B PAGE 4 of 10
1.0 SCOPE
The requirements of the latest edition of the following codes, regulations and standards
shall be met or exceeded, except as superseded herein. In cases where more than one
code, regulation or standard apply to the same condition, the most stringent shall be
followed. In the event of a conflict between this specification and other specifications or
correspondence, the OWNER shall be consulted and a ruling, in writing, shall be
obtained before any work is started.
Where supplemental information is required, the following codes and standards shall be
used.
Any deviation from this specification must be approved, in writing, by OWNER. Such
written approval must be obtained prior to the commencement of any work which would
constitute such a deviation.
362829727.doc
SPECIFICATION FOR ELECTRICAL Petro-
AREA CLASSIFICATION
Energy
DOCUMENT NO : GEN-SPC-ELC-6610 REV. : B PAGE 5 of 10
Zone 2 locations are locations in which an explosive atmosphere is not likely to occur in
normal operation and, if it occurs, will exist only for a short time.
4.0 DRAWINGS
(a) The classification and extent of each area with all major structures and
equipment indicated.
(b) All equipment which is a source of hazardous gas or vapor identified by:
Equipment number
Flammable material(s) handled
Atmosphere group according to the IEC
5.1 The codes, as referred under Clause No. 2.0 above shall be used to determine minimum
requirement of area classification.
5.2 When designing area classification, consider the problem of transient vapors from
hazardous sources. Further area classification is required to cover these conditions.
362829727.doc
SPECIFICATION FOR ELECTRICAL Petro-
AREA CLASSIFICATION
Energy
DOCUMENT NO : GEN-SPC-ELC-6610 REV. : B PAGE 6 of 10
5.3 Mixtures of gases of different groups may be involved, or sources of both heavier-than-
air and lighter-than-air gases may exist within an area. In classifying such areas, all of
the following apply:
(a) Upon release, gas mixtures are considered to separate immediately into their
separate gases. If the separate gases are of different groups, use electrical
equipment within each classified area suitable for all the groups involved.
(b) In mixtures of Group II B and II A gases per IEC, the Group II B gases are
disregarded if they constitute 30% or less by volume of the mixture.
(c) In areas which are adequately ventilated and have lighter-than-air vapors, the
hydrogen in a gas mixture is disregarded if it constitutes 30% or less by volume
of the gas mixture.
5.4 Special consideration shall be given to those areas where large volumes of hazardous
materials are being handled or high pressures are utilized.
5.5 Consideration shall be given to classification of areas around sampling points, relief
vents etc. Location of electrical equipments near sampling points and relief vents shall
be avoided.
6.1 Purging/pressurizing systems permit the safe operation of electrical equipment under
conditions of hazard for which approved equipment may not be commercially available.
Electrical equipment selection and installation for the classified area shall be in
accordance with IEC 60079 and BS 5345. The selection shall follow the table here
below.
362829727.doc
SPECIFICATION FOR ELECTRICAL AREA
Petro-Energy
CLASSIFICATION
Note: Minimum level of ingress protection shall be IP55, for Equipment in hazardous area.
362829727.doc
SPECIFICATION FOR ELECTRICAL AREA
Petro-Energy
CLASSIFICATION
362829727.doc
SPECIFICATION FOR ELECTRICAL AREA
Petro-Energy
CLASSIFICATION
362829727.doc
SPECIFICATION FOR ELECTRICAL AREA
Petro-Energy
CLASSIFICATION
362829727.doc