Académique Documents
Professionnel Documents
Culture Documents
PARTS LIST
12 Torx nuts
RIGHT SIDE
ROOF RAIL
Right center roof rail cover
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46748 (1109) 08L02-TK8-1000-91 1 of 6
INSTALLATION 2. Open the tailgate halfway. Using a trim tool, pry up
the rear of the left roof molding rear cover.
Customer Information: The information in this
installation instruction is intended for use only by skilled LEFT ROOF
MOLDING TAILGATE
technicians who have the proper tools, equipment, and REAR COVER Open halfway.
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
do-it-yourselfers.
SCRIBE LINE
FRONT
020104BB
LEFT ROOF
MOLDING
REAR COVER
AIR SAW
020103AB
2 of 6 AII 46748 (1109) 2011 American Honda Motor Co., Inc. All Rights Reserved.
4. Remove and discard the four roof molding clips from 6. Measure and mark the left roof molding as shown
the roof molding and the stud bolt on the roof. using a felt-tip pen.
518 mm
FRONT
ROOF
95 mm
850 mm MARK
150 mm
LEFT ROOF STUD MARKS
MOLDING BOLT 556 mm
FELT-TIP
MARKS PEN
LEFT ROOF
MOLDING
042701BB
FRONT
020105AB
MARK
5. Remove any sealant that is on the base of the stud
bolts.
FRONT MARKS
STUD BOLT STUD BOLT
MARKS
SEALANT
SEALANT
Remove any
excess.
AIR SAW
LEFT ROOF
MOLDING
020107BB
FRONT
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46748 (1109) 3 of 6
8. Install one roof molding clip (supplied) to the front of 10. Reinstall the cut pieces of the left roof molding onto
the left roof molding. the roof of the vehicle as shown.
LEFT ROOF
LEFT ROOF MOLDINGS
MOLDING
(Front)
FRONT
ROOF MOLDING
CLIP
ROOF MOLDING
CLIP
FRONT
FRONT LEFT
020108AB 020110BB
ROOF MOLDING
11. Install the left side roof rail with six Torx nuts. Make
9. Reinstall the left roof molding rear cover. sure the roof rail is installed in the correct position.
NOTE: If the roof molding cover is not even with the Torque the Torx nuts to: 10 Nm (7.3 lbfft)
roof, it is installed incorrectly. Reinstall the roof
molding cover properly. LEFT SIDE
ROOF RAIL
LEFT ROOF
MOLDING TAILGATE
REAR COVER
6 TORX
NUTS
FRONT
020109AB
FRONT
6 STUD
BOLTS 020111BB
4 of 6 AII 46748 (1109) 2011 American Honda Motor Co., Inc. All Rights Reserved.
12. Install the left front roof rail cover to the left side roof 16. Attach masking tape to the vehicle panel around the
rail with two clips. middle roof rail support.
2 CLIPS
LEFT ROOF
TORX SCREW RAIL MIDDLE
SUPPORT
FRONT
LEFT FRONT
ROOF RAIL
COVER
MASKING
TAPE
FRONT
LEFT SIDE VEHICLE
ROOF RAIL 020112BB PANEL
061802AB
13. Secure the left front roof rail cover to the left side roof
rail with one Torx screw.
17. Hook the left center roof rail cover to the left roof rail
14. Install the left rear roof rail cover to the left side roof
middle support as shown.
rail with three clips.
LEFT REAR
ROOF RAIL
COVER
FRONT
FRONT
LEFT SIDE
ROOF RAIL LEFT CENTER
ROOF RAIL
020113BB COVER 020114BB
15. Secure the left rear roof rail cover to the left side roof
rail with one Torx screw.
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46748 (1109) 5 of 6
18. Install the left center roof rail cover to the left roof rail
middle support as shown. Make sure there is no
clearance between the left center roof rail cover and
the left roof rail middle support.
INSIDE VIEW
LEFT ROOF
FRONT RAIL MIDDLE
SUPPORT
Push.
LEFT CENTER
ROOF RAIL Turn.
COVER
6 of 6 AII 46748 (1109) 2011 American Honda Motor Co., Inc. All Rights Reserved.