Académique Documents
Professionnel Documents
Culture Documents
www.huawei.com
Hardware Structure
Features and benefit
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 3
AAU3902 - Hardware Structure
AU
module
1.8 RU module
PIU-S/PIU-2R
module
2.1 RU
module
MU 48 V power
module input
1.8RU Two CPRI
indicator ports
High-frequency 1.8-
26
2.1 RU ANT2 DIN port
indicator
A pair of AISG ports
MU
indicator
Low-frequency
900 MHz
ANT1 DIN port
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 4
AAU3902 - Equipment Specifications
Item AAU3902
Dimensions 2000 mm x 350 mm x 260 mm
Weight Single frequency band: 51 Kg
Dual-frequency band: 60 Kg
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 5
AAU3902 - AU
Specifications of an AU
Antenna unit (AU) is a 2H1L antenna, which is the
major bearer of an AAS module. Mounting brackets, Low- High- High-
frequency frequency frequency
RU, MU, and PU are installed on the AU. An AU02 passive active
Antenna passive
antenna antenna
H L (2 m)
provides the following parts and functions: antenna
Frequency 790 MHz to 1710 MHz to 1710 MHz to
1. Enclosure frame and radome H(1.4 m) Band 960 MHz 2690 MHz 2690 MHz
2. Antenna element 17 dBi 17 dBi
Antenna 16 dBi
3. Reflection panel Gain
Vertical 10o 4 to 6o 4o to 6o
4. Feeding network Beamwidth
5. Phase shifter Horizontal 65o 65o 65o
Beamwidth
6. Driving mechanism of the RET Passive:
1710 to 2690 MHz Active: RET 0 to 10o 2o to 10o 0 to 12o
1710 to 2690 MHz
7. High-speed blind-mate ports for the Passive:
Adjustment
790 to 960 MHz Range
communication between AUs and CMs,
Mechanical 3, 1.5, 0, +1.5, +3
between AUs and RUs, and between AUs and Tilt
antennas.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 6
AAU3902 - RU
A radio unit (RU) is an active RF module, which uses 4T4R Specifications of 2100-1800 MHz RU
and supports two TRXs for one antenna polarization. The Item RU44-2.1 GHz RU44-1.8 GHz
circuit is basically the same as that of an RRU. The 2100 Frequency Band 1920 MHz to 1725 MHz to
1980MHz 1785MHz
MHz RU delivered in this version has the following parts and
2110 MHz to 1820 MHz to
functions: 2170MHz 1880MHz
1. Channel processing, clipping, and digital IF signal Working Mode UMTS GSM or LTE
Hardware 4T4R 4T4R
processing such as DPD
Structure
2. TX and RX RF links processing Output Power 2x40 W 2x40 W
3. Active antenna calibration and compensation Power 405 W 405 W
4. DBF parameter configuration Consumption
Receiver 125.5 dBm GSM: 114 dBm
5. Antenna polarization Sensitivity/Single
LTE: 106.6 dBm
6. Local operation and maintenance for RUs Channel
Receiver Cannot be tested Cannot be tested
DPD Channel CPU Clock and Power
Sensitivity/Four
correction local supply Channels
frequency
Carrier 8 (1T2R) or 4 GSM:8 (1T2R)
(2T2R, 1T4R, and LTE: 2 (2T2R,
RF PA 2T4R) 2T4R, and 4T4R)
SD6212 RFRF
Channel PA
PA
FPGA Channel PA
RF
Channel
Channel
Transient Working 40 MHz/PA, 60 GSM: 35 MHz/PA
Channel
correctio IF Bandwidth MHz/Rx LTE: 40MHz/PA,
T/R IQ RF LN
n handl
RF
60 MHz/Rx
Connect RF
Channel LNA
LN
DBF ing
Channel
RF
Channel LNAA Blind-mate
ed to the SEDES Duplexer 60 MHz 60 MHz
Channel A RF
MU Maintena Bandwidth
nce and connector
test Connected Power Supply 48 V DC (36 V 48 V DC (36 V
to the
antenna
DC to 57 V DC) DC to 57 V DC)
port on the
AU
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 7
AAU3902 - MU
A management unit (MU) is the common management of
an AAU, which has the following parts and functions:
Protection
and filtering
1. CPRI convergence and distribution
Power T/R IQ and power
2. Ports for power supply and CPRI hardware supply Connected to slot 3
3. Light protection, slow start-up, electromagnetic Fan control
Clock
interference (EMI) prevention, and filtering
CPU T/R IQ and power
4. AAS O&M and RU management Connected to slot 2
FGPA
5. Control of the antenna built-in motor and level-2 CPRI
deframing
phase shifter CM controls
frame forming
T/R IQ and power
6. Control of the PU (with motor) Maintenance
and test
Connected to slot 1
SERDES
CPRI 48 V
Logical Structure of an MU
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 8
AAU3902 RET Scheme
Active unit
2.1A 1. The RET of the 3-array antenna can be
controlled independently.
High-frequency active array
CMB1 TRX 2. Only inner control is supported for the high-
V2D6 TRX
frequency active array.
V network
Low-frequency passive array + phase shifter
Level-2
phase hierarchical control for the motors. The
shifter antenna has three motors controlling the three
1.8/2.6A arrays, respectively. The motors are controlled
CMB2 TRX by one remote control unit (RCU).
TRX 5. Outer control is performed through a pair of
outer multi-core ports at the bottom of the
TRX
TRX antenna. The ports can be cascaded. One
multi-core control channel is provided in the
LVTTL antenna controlling the motors of the two
Motor1 CM passive arrays. The channel supports cascading
Motor and is identified by a serial number.
RS485 Passive motor
6. Outer control does not support the OOK port.
control control
Motor 2 Phase shifter When outer passive modules use the OOK
on the
antenna ports, connect the SBT to the antenna to
Hierarchical isolate and demodulate the OOK signals.
control for
motors
Motor 3
CPRI
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 9
AAU3902 Benefit
Architecture
Site Coverage
Achieving
Requiring wide and deep
less antenna coverage
space and
reducing
boxes
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 10
Site Solution
Cost Saving Item Benefit Advantage (comparing with the RRU)
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 11
Capacity Solution
Capacity
Measure Supported by the AAS Module
Expansion Method
More spectrum Add more frequencies. Yes
resources
Add more frequency bands. Yes if AARUs operating the related frequency bands are installed
Multiple sectors: transition from three-sector to Yes. A single AAS module can support two sectors. A single
six-sector; AARU supports different sector combinations.
Multiple channels: transition from 1-channel to 2- Yes. A single AAS module supports four RF channels and
Networking: channel and then to 4-channel; four-way transmit therefore can achieve four-way receive or transmit diversity. A
multiple or receive diversity single AARU supports different RF channel combinations.
sectors/channels/s
ites, or Hetnet Multiple sites: short distance between sites Yes
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 12
AAU3902 Features
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 13
Vertical Multiple Sectors
Application Scenarios
The downlink load of the target cell has reached or exceeded the downlink load threshold
(70%) for capacity expansion.
In densely-populated urban areas, the site height higher than 25 m is recommended, and the
distance between two eNodeBs is about 500 m.
In common urban areas, the site height higher than 30 m is recommended, and the distance
between two eNodeBs is less than 1000 m.
The Cell A downtilt angle on the site is smaller than or equal to 10. CELL A CELL A
Traffic is available near the site. Deploy this feature in scenarios where traffic in inner cells
accounts for 40% to 80% of the total traffic.
Solution
The Vertical Multiple Sectors feature splits a sector served by AAS modules into an inner sector and an outer sector. The inner and outer
sectors correspond to an inner cell and an outer cell, respectively. These cells use the same frequency but have overlapping areas.
Benefits
This feature cover the area with one more sector to let users reuse radio resource which may lead to increase on capacity without adding
frequencies or RF modules. In the user non-uniform distributed scenario, the gain is as follow.
UMTS: Increases network capacity by 30% to 70% compared with the capacity of a site in a horizontal three-sector networking.
LTE: Increases network capacity by 20% to 40% compared with the capacity of a site in a horizontal three-sector networking.
Specifications and Limitations
The cells served by this feature do not support four-way receive diversity due to limited capabilities of AAS modules.
AAU3902 is required.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 14
Vertical Multi-Sector DL Capacity Gain
DL Cell Average Throughput for Full Buffer
30-70%
20-40%
3 Sector 3 Sector
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 15
Virtual Four Uplink Channels (Vertical)
Application Scenarios
Uplink capacity is limited and no extra frequencies are available, such as in densely
populated areas.
There are no problems such as service drop or access failure due to coverage.
The uplink interference over thermal (IoT) in the cell is high.
Solution
The Vertical Four Uplink Channels feature enables four-way receive diversity for a sector
by allocating four connection ports to the sector vertically. Without this feature,
conventional RRUs or RFUs must use two sets of dual-polarized antennas to enable four- Inner beam 4RxD Outer beam
way receive diversity.
This feature provides extra receive diversity gains and array gains, thereby increasing the
uplink throughput and network capacity Area 1 Area 2 Area 3
Benefits
Note
UMTS: Compared with two-way receive diversity, this feature helps increase uplink 1) The interference between areas 1 and 3 is
capacity by 40% to 60%. small due to the gap area: area 2.
LTE: Compared with two-way receive diversity, this feature helps increase uplink capacity 2) UEs in area 2 obtain four-way receive
by 10% to 45%. diversity gains because their signals can be
received by inner and outer beams.
Specifications and Limitations 3) The RoT for the average uplink load specific
The cells served by user specific tilt and four-way receive diversity, and do not support the to four-way signals is twice larger than the RoT
Vertical Multiple Sectors feature due to limited capabilities of AAS modules. for the average uplink load specific to two-way
signals.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 16
Virtual Four Uplink Channels (Vertical) Capacity Gain
Cell Average Throughput for Full Buffer Service
40-60%
AAS Virtual 4 Channels
Benefits 10-45%
Improve receiver
sensitivity and
uplink coverage.
2Rx 2Rx
30.00%
two vertical beams which radiate at 25.00%
20.00%
+45 polarization and at -45 15.00%
polarization 10.00%
5.00%
In area B where these two beams 0.00%
5% 10% 50% 70%
overlap, the function enables four-way
max 10.03% 10.19% 29.54% 43.97%
receive diversity
min 6.03% 7.60% 21.79% 34.44%
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 17
User Specific Tilt (LTE Only)
Application scenario
Cells selected for user specific tilting provide continuous coverage.
There are no coverage problems, or there are coverage problems but the
problems are not serious, for example, in densely populated urban areas. In
densely populated urban areas, the site height is higher than 25 m, and the
distance between two eNodeBs is equal to or less than 500 m. In common urban
areas, the site height is higher than 30 m, and the distance between two eNodeBs
is less than 1000 m.
The downtilt angle on the site is smaller than or equal to 10.
There is traffic in cell centers.
UEs support 4x2 or 4x4 closed-loop MIMO.
Solution
The AAS can use an active antenna to form two transmit beams in each polarization direction for a total of four transmit beams in the
two polarization directions. Together with LOFD-001003 DL 4x2 MIMO or LOFD-001060 DL 4x4 MIMO in closed-loop mode, the AAS
generates four downlink channels on the vertical plane in a cell.
As shown in Figure , the red beam is a wide beam generated for control channels and the other three beams are narrow beams
generated for traffic channels. These narrow beams are formed for different UEs based on the precoding matrix indicators (PMIs)
reported by these UEs and the associated codebooks. For the server cell, the UST has beamforming gain, and for the neighbor cell,
the UST has inter cell interference reduction gain.
Benefit
This feature increases the signal power of UEs close to the AAS and reduces the interference with other cells, thereby increasing
system capacity.
Specification and restriction
The cells served by user specific tilt and four-way receive diversity, and do not support the Vertical Multiple Sectors feature due to limited
capabilities of AAS modules.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 18
User Specific Tilting DL Capacity GainLTE Only
22
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 19
Executive Summary for AAU3902 Field Trial
Vertical 4 Receive Diversity
AAU3902 is a new type of antenna which differently from
traditional passive modules allows to enable advanced
beamforming functions in accordance with our needs . Below
the results reached for each of active features tested:
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 21
Product overview AAU3911
Hardware Structure
Features and benefit
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 22
Hardware Structure - AAU3911
Mounting
kit Upper
handle
Plastic
cover RU in the
upper slot
Plastic cover
bracket AU
RU in the lower
slot
Lower
handle
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 23
Equipment Specifications of AAU3911
Item AAU3911
Dimensions With metal cover: 2020 mm (H) x 359 mm (W) x 290
mm (D) (79.53 in. x 14.13 in. x 11.42 in.)
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 24
Introduction to Functional Modules of AAU3911
Functional modules of AAU3911 consist of the active module RU and the antenna module AU.
An RU is an RF unit, which transmits and transforms signals between BBU and the antenna system. The types of RU
include:
Power
Frequency Number
RU Code Consumption Bandwidth Power Sensitivity
Band of TR
(100% Load)
UMTS:
RU3832 2100 2T4R 02310PPY 385 W UO: 60 MHz 2 x 60 W
-126.1 dBm
UMTS:
UO: 60 MHz -126.1 dBm
RU3832 AWS 2T4R 02310QNU 385 W
LO: 50 MHz
2 x 60 W
LTE:
-106.5 dBm
GO/GL: 35 1800: GSM: -114.0 dBm
RU3952m 1800 2T4R' 0231XXXX XXXW MHz 2 x 40 W LTE:
LO: 40 MHz -106.5 dBm
UMTS:
RU3952m 2100 2T4R' 0231XXXX XXXW UO: 60 MHz 2 x 60 W
-126.1 dBm
LTE:
RU3260 2600 2T4R 02310QER 330 W LO: 50 MHz 2 x 40 W -106.5 dBm@ (1T1R 25
RB)
An AU is an antenna unit, which is the main bearing part in AAU3911. The AU can be categorized into four types
according to the frequency band that it supports.
AU Frequency Band in the Upper Slot (MHz) Frequency Band in the Lower Slot (MHz)
AU11Ia 2500 to 2690 1710 to 2170 + 690960
AU11Ib 1710 to 2690 690960
AU11Ic 1710 to 2170 25002690 + 690960
AU11Id 2305 to 2360 25002690 + 690960
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 25
Introduction to Functional Modules of
AAU3911 RU
AAUs can use three types of RUs: RU of 2T4R, RU of 2T2R, and RU of 4T4R, which support different
numbers of receiving and sending channels.
The main functions of RU are as follows:
1. Receives downlink baseband data from the BBU and transmits uplink baseband data to the BBU,
enabling communications between the RU and the BBU.
2. Receives RF signals from the antenna system, down-converts the received signals to IF signals,
amplifies the IF signals and performs ADC. The TX channel filters downlink signals, performs DAC and
up-converts RF signals to the TX band.
3. Provides the duplexing function for RF channels, enables RX signals and TX signals to share the same
antenna path, and filters the RX and TX signals.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 26
Exterior of RU
4T4R/2T4R 2T2R
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 27
Introduction to Ports of RU 2T4R/4T4R
Item Silkscreen Remarks
(1) Ports in the RTN (+) Power port
cabling cavity
NEG (-)
CPRI0 Optical/electrical port 1
CPRI1 Optical/electrical port 1
(2) Ports at the ANT_TX/RXA TX/RX port A,
bottom supporting RET signal
transmission
ANT_RXC RX port C
ANT_RXD RX port D
ANT_TX/RXB TX/RX port B
The difference between the ports on 2T4R and 2T2R RUs lies only in the number of RF ports at the bottom.
Other ports including those for power, CPRI, RET, alarm, and indicator are the same.
Ports of 4T4R and 2T4R RUs are the same. On the 4T4R RU, port C and port D can be shared between RX and
TX.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 28
Introduction to the Components of
AAU3911 AU
The functions of the AU are as follows:
Provides an antenna array and a feeder, phase shift network and transmission
system.
Provides the built-in antenna motor to control the circuit.
Provides antenna capability information, combiner types, and RU in-position
information reporting.
Provides overall installation and RU installation ports.
Provides passive ports for RRUs and RFUs.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 29
Exterior of AU
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 30
Electrical Parameters of AU
AU Electrical Parameter
1710 1920 2500
Frequency Range (MHz) 690820 790862 824894 880960
1880 2170 2690
Gain (dBi) 15 15.5 15.5 16 17 17.5 18
65 63
Horizontal 3 dB Beam Width ()
9.5 6.4
Vertical 3 dB Beam Width ()
Side Lobe Suppression for First Side Lobe Above >17 >17
Main Beam (Typ.) (dB)
>25 >25
Front to back ratio, copolar (Typ.) (dB)
Polarization +45, -45
Electrical Downtilt () 0 - 10, continuously adjustable
<1.5
VSWR
Intra-system: 28
Isolation Between Ports (dB) Inter-system: 28 (typ: 30)
Maximum Input Power per Port (W) 80 80
160 0
Maximum Total Input Power (W)
-153 (2 x 43 dBm carrier)
Intermodulation IM3 (dBc)
50
Impedance ()
Grounding DC Ground
Note: The 0.3 dB loss of combiner needs to be considered for counting the gain of an AU with a
built-in combiner.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 31
Types of AU
AU11Ia AU11Ib AU11Ic AU11Id
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 33
Description of Ports on the AU 2
6 5 4 3
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 34
Logical Principle of AAU3911 RET
Antenna The RET of AAU3911 antenna is realized through the AISG. The antenna has
three built-in logical RCUs for remote adjustment of the three antenna tilt
angles. The RET system provides four AISG ports. Two of the AISG ports are
Phaser for tilt adjustment of active RUs in the upper and lower slots, and the two
Subunit1 ports are located in the middle and at the bottom of the antenna. The other
Subunit2 two AISG ports at the bottom of the antenna are for the passive tilt
Subunit3 adjustment or RRU cascading. Each logical RCU has its RCU ID.
For the logical RCU, software design constraints are as follows:
Each RCU can set up only one AISG link. Two links cannot be set up.
RU-A(U) RCU1
RU-A(D)
AISG
RCU2 MOT After the RCU link is established, the RCU serial number is not displayed in
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 35
RF Cable Connections of AU11Ic
The ones on the left part correspond to the connection in the upper slot. The ones on the right
part correspond to the connection in the lower slot.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 36
Functions and Features of AAU3911
AAU3911 integrates functions of the RF module into the antenna. The features of
AAU3911 are as follows:
A maximum of two active bands can be integrated in AAU3911.
Compared with traditional RRUs, AAU3911 can reduce the jumper loss by
about 0.8 dB and save 10% of power by integrating RF modules into the
antenna.
AAU3911 adopts the modularized structure and supports fast installation and
maintenance, reducing product delivery time.
AAU3911 supports uplink 4-way receive diversity, eliminating the bottleneck of
uplink receiving capacity.
AAU3911, as an active antenna unit, can be connected to RRUs or RFUs in the
live network.
AAU3911 has strong evolution ability. It is convenient to evolve from 2T2R to
2T4R and from 1A+2P to 2A+1P.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 37
High Integration and Simplified Sites
15 Boxes 6 Boxes
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 38
Less Feeder Loss and Power Consumption
AAU
Solution 0 Feeder loss
(decreased by
0.8 dB)
3 dB cable loss 0.8 dB jumper Power and CPRI 10% power saving
loss
(5 m)
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 39
Increased Uplink Capacity
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 41
Inter-Frequency Mutual Aid
The Inter-Frequency Mutual Aid feature allows a radio frequency (RF) module
to receive and transmit signals on one frequency band and receive signals on
another.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 42
Inter-Frequency Mutual Aid - Modules
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 43
Inter-Frequency Mutual Aid - Benefits
The Inter-Frequency Mutual Aid feature achieves dual-band four receive
(RX). When used in newly deployed dual-band networks or during
transitions from single-band networks to dual-band networks, this feature
requires fewer external combiners or antennas, reducing costs.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 44
Inter-Frequency Mutual Aid - Benefits
The Inter-Frequency Mutual Aid feature achieves dual-band four receive
(RX). When used in newly deployed dual-band networks or during
transitions from single-band networks to dual-band networks, this feature
requires fewer external combiners or antennas, reducing costs.
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 45
FOA AAU3902 scenario
Active antenna configuration
o LTE1800 V4R + UMTS2100 VMS (V4R)
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 46
FOA AAU3902 scenario
RU1800
48V
DCDU
BBU UMTS
UPE
U
WBBPf3 RU2100
FA
N WBBPf3
UPE
U
WBBPf3 UMPTb2 Iu-b (IP) +
S1/X2 (IP)
MU
CPRI
DCDU
BBU GL
UCIU
800-900 MHz
LBBPd2
FA
GTMU
N LBBPd2 CPRI
UPE
U
LBBPd1 UMPTb2 A-bis (TDM)
TMA
800-
900
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 47
FOA AAU3911 scenario
Active antenna configuration
o LTE1800 2T4R + GSM1800 2T2R +
UMTS2100 2T2R
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 48
FOA AAU3911 Scenario
48V
CPRI RU3952m
2T4R
(1800)
CPRI
DCDU
BBU UMTS
WBBPf3
UPE
U
48V
WBBPf3
FA
N WBBPf3
UPE
CPRI RU3952m
2T4R
U
WBBPf3 UMPTb2 Iu-b (IP) + (2100)
S1/X2 (IP)
CPRI
DCDU
BBU GL
UCIU
800-9000 MHz
LBBPd1
FA
GTMU
N
UPE
U
LBBPd2 UMPTb2 A-bis (TDM)
TMA
2600 MHz
800-
non usato 900
HUAWEI TECHNOLOGIES CO., LTD. Huawei proprietary. No spread without permission. Page 49
Thank you
www.huawei.com