Académique Documents
Professionnel Documents
Culture Documents
BR161SM-GATE-A
-v11
Alarm Notification
Remote Control
www.bieneelectronics .com
Features
Internal 2-band (BR160SM) / 4-band (BR161SM) GSM-modem SIM900R / SIM900
6 digital input
3 Open-Drain MOSFET output
1 Power Relay output
Alarm notification using SMS messaging via cell phone
Control via SMS
Configuration from cell phone
Output Control
BR160SM-Gate-A and BR161SM-Gate-A has 3 open-drain Outputs and 1 Power Relay Output.
These may be controlled with SMS messages from approved users. To set any output as you
like, you need only to send an SMS message.
For Gate control call to module from phone. Relay output output for Gate automation device
control. Abonent numbers can write to module and SIM card can with SMS command.
Alarm SMS
SMS messages can be sent to users when an input reaches an alarm state.
Alarm when 0-1 or 1-0 event at digital input (see jumpers setting). Text for Alarm SMS can
change with SMS command. Alarm SMS BR160SM-Gate-A can send up to 4 cell phone
numbers.
Module Programming/Configuration
BR160SM-Gate and BR161SM-Gate can be configured (programming) remotely with SMS
command.
Technical Specification
Environmental Conditions
Normal operating -20+55C
temperature.range
Restricted operating -25+70C
temperature range (SIM900 can work, but the deviation from the GSM specification may occur)
Storage temperature range -40 to +80C
Humidity 0-95% non-condensing
Physical parameter
Board dimension 103 x 86.5 mm
Enclosure dimension 106 x 100 x 58 mm
Box DIN-rail mounting
Weight
SIM Card
Small SIM-card with 3V / 1.8V technology
1. Disable PIN code request so it will not prompt for a PIN code on turning on.
Note:
The BR160SM and BR161SM can only be used with small SIM-cards with 3V/1.8V
technology.
For SIM card preparation (add SMS message and phone numbers) you can use cell
phone or external GSM modem.
SIM card change if power turn off.
LED indicators
Antenna connection
GSM antenna must be connected to SMA connector X5. Use only the 50Om antenna of the
necessary frequency range. Base version complected with direct mount GSM antenna.
Note: It is very important that the antenna is installed on a location where the GSM-network
coverage is sufficient. Please also check carefully that antennas are not installed nearby
technical devices, cables etc which could influence the GSM-radiation.
Digital inputs and outputs must be connected with screw terminal blocks X2-X4.
For Power supply, Inputs and Outputs connection used screw terminal blocks.
Jumpers
Jumper J2
Inputs
Outputs
You can use J2 pin header for in-board pull-up resistor connection.
Disable PIN code request so it will not prompt for a PIN code on turning on.
Write 2 authorized numbers to Phone Book (position 1,2). It can make with SMS command
First two numbers should consist + and country code
Write gate open user cell phone numbers to Phone Book (position from 3);
you can added and deleted numbers with SMS command.
Note:
1) for some operators and countries required + and country code before cell phone
numbers;
2) for other operators and countries without + and country code;
write in the form in which you can see on your phone number when to you call other
abonent. (see Note page 11)
Repeat the first two numbers (positions 1 and 2) at position from 3
Note:
The module can only be used with small SIM-cards with 3V/1.8V technology.
For SIM card preparation you can use cell phone or external GSM modem.
Set phone numbers from which management (module settings, add/delete SMS phone
book) is authorized
Phone Book
1 A1 <Phone number1> 1)
2 A2 <Phone number2> 1)
Example: enable all phone numbers (disable authorization numbers; all cell phone enabled for
gate open)
Phone Book
1 A1 99
2 A2 <Phone number2>
Phone Book in SIM and EEPROM
Phone Book
001 A1 <Phone number 1>
002 A2 <Phone number 2>
003 A3 <Phone number 3>
004
Number at location 001 and 002 - privileged .number: from this cell phone you can send
SMS command for setting and control. For example +37122842915
Number at location 001 and 250 - numbers, enabled for gate open process.
If at location 001 empty or short number, for example 001 or 99, then all cell phone enabled
for gate open process.
You can write numbers to SIM Phone Book. with SMS command 2345A or deleted number from
SIM Phone Book with SMS command 2345D
You can add new number to phone book 2345A SMS command.
- for example 2345A,+37122842915
- If phone book full, you receive answer SMS 'SIM Phone Book Full'
- If phone book not full, new number entered to first empty position in phone book
you receive SMS 'NR 17 +37122842915 added' (you receive also position in phone
book)
- If number exist in phone book, you receive SMS 'NR 42 +37122842915 exist'
(number exist in phone book at position 042)
- If number not exist in phone book, you receive SMS 'NR 250 +37122842915 added'
(number added at position 250)
You can delete new number from phone book 2345D SMS command.
- for example 2345D,+37122842915
- If number not exist in phone book, you receive answer SMS 'NR +37122842915 not
exist'
- If number exist in phone book, you receive answer SMS 'NR 250 +37122842915
deleted'
Example:
2345A,+37122842915
Phone Book
001 A1 <Phone number 1>
002 A2 <Phone number 2>
003 A3 <Phone number 3>
004 +37122842915 +37122842915
2345D,+37122842914
Phone Book
001 A1 <Phone number 1>
002 A2 <Phone number 2>
003 A3 <Phone number 3>
004 +37122842915 +37122842915
Answer SMS:
NR 12 +37122842915 added - if number added to SIM phone book at location 012
NR 12 +37122842915 exist - if number exist in SIM phone book at location 012
Answer SMS:
NR 11 +37122842915 deleted - if number deleted from SIM phone book (from position 011)
NR +37122842915 not exist - if number not exist in SIM phone book
Remote control
We can turn on and turn off module outputs with SMS command: 2345S and 2345R.
6789S1 6789S4 I1=0 I2=0 I3=0 I4=0 I5=0 I6=0 Set output
O1 OFF, O2 OFF, O3 OFF, O4 OFF
Pulse(sec):2 MaxNN=250 with password 2
B= 11.9V
6789R1 6789R4 I1=0 I2=0 I3=0 I4=0 I5=0 I6=0 Reset output
O1 OFF, O2 OFF, O3 OFF, O4 OFF
Pulse(sec):2 MaxNN=250 with password 2
B= 11.9V
2345T1 2345T9 I1=0 I2=0 I3=0 I4=0 I5=0 I6=0 Set pulse length; 0- latch mode
2345T0 O1 OFF, O2 OFF, O3 OFF, O4 OFF 1 - 1 sec 9 9 sec
Pulse(sec):2 MaxNN=30 default 2 sec
B= 11.9V
2345B10 I1=0 I2=0 I3=0 I4=0 I5=0 I6=0 00 - Enable Gate Open Pulse (default)
2345B00 O1 OFF, O2 OFF, O3 OFF, O4 OFF 10 Disable (Blocking) Gate Open Pulse
2345B01 Pulse(sec):2 MaxNN=30 01 All numbers enable for Gate Open
B= 11.9V
2345L,0100 BAT.voltage Min:100 Max:150 Set MIN level in V for BATTERY voltage
(with password 1)
0100 = 10.0V
if use analog input A4 (Jumper J0 not set)
maximum voltage on AN4 10V
2345L BAT.voltage Min:100 Max:150 Get BATTERY Voltage setpoint levels
2345G,001 1:+37122832798 Get number from SIM phone book , position 001 ..
250
(with password 1)
2345Z OK Restart (with password 1)
SMS command
with password 1 for all SMS command, except 'S', 'R', 'Q',
with password 2 for SMS command 'S', 'R', 'Q',
If you change first number in SIM phone book, required restart module for new installation.