Académique Documents
Professionnel Documents
Culture Documents
Innovative Development in
Power Systems
JURUTERA
THE MONTHLY BULLETIN OF THE INSTITUTION OF ENGINEERS, MALAYSIA
JURUTEA
FEBRUARY 2016
KDN PP 1050/12/2012 (030192)
C O NTEN TS
ISSN 0126-9909
Power Systems
W
e talk about smart power systems and about integrating information technology
with power system grid. But do we ever look into the safety aspects of the power
systems that we have developed and installed to date?
In recent years, there have been numerous fatal incidents concerning power systems
in residential, commercial and industrial areas. These include electrocution due to water
By Ir. Yau Chau Fong heater installation works, faulty installation of electrical equipment, protection devices and
Chairman, earthing systems as well as lack of safety awareness in substation operations. Many more
Electrical Engineering Technical
Division such incidents are not even reported.
In December last year, we organised an international conference on Safe, Smart
Ir. Yau Chau Fong, graduated from and Innovative Development In Power Systems where 27 renowned speakers were invited
Universiti Malaya and has a total
of 14 years of professional working to present and address the above subjects.
experience in the consulting industry. Our cover story is an exclusive interview with Datuk Seri Ir. Azman bin Mohd, President
He is currently serving as Excomm
Member and Council Member of and Chief Executive Officer of Tenaga Nasional Berhad (TNB), the countrys largest electric
IEM. He is also the current Vice utility company. He shares with us how TNB provides safe, smart and innovative power
Chairman of the IEM Standing
Committee of Activities. systems.
In the coming months, EETD plans to hold a series of technical talks, courses and
seminars on the importance of safe, smart and innovative power systems. We will also hold
dialogues and collaborate with various stakeholders involved in the development of power
systems, both locally and internationally.
We hope our members will benefit from these activities and continue to support our
efforts towards the development of safe, smart and innovative power systems.
TNB UP TO
CHALLENGES
W
ith the introduction of Independent Power Producers (IPPs)
since late 90s, Tenaga Nasional Berhad (TNB) will no longer
the sole stakeholder when it comes to power generation
although its core activities continue to be the generation,
transmission and distribution of electricity. Now, electric power is
produced by both TNB and several IPPs.
After the introduction of IPPs, TNB is no choice of products and services which will create new
longer the sole stakeholder in power consumer experience and feedback and which will
generation. How will TNB approach such objectively lead to greater customer satisfaction, trust
and needs.
a challenge in terms of smart grid/grid
integration if the Energy Commission opens
up the Transmission/Distribution systems According to the Energy Commission (EC)
to accommodate multiple sources of statistics on electrical accidents, presented
generation and distributors? at the recent IEM-IET Electrical Conference
2015 (IIEC 2015), the highest rates were
Datuk Seri Ir. Azman: Smart grid will enable the recorded in the utility company. Tell us the
easier integration of distributed generation including RE measures that TNB has taken to reduce and
(Renewable Energy). The TNB network system is ready mitigate this situation.
to accommodate the dynamics of the Distributed
Generation (DG) with the incorporation of smarter Datuk Seri Ir. Azman: Most of the accidents were due
controls and ICT communication devices. to either human factor or equipment failures. To address
What is required is to balance the energy demand- the human factor, we are focusing on safety awareness
supply mix with the right regulatory policies to encourage and to further enhance our technical competency. These
growth in DG with the appropriate mechanisms to ensure include:
adequate return on investments by all parties. In addition, More stringent SOPs have been established and safety
any change in the Transmission/Distribution system will gears given to the operational staff.
need to be gradual to ensure the stability and security Continuous education and awareness programmes
of the national grid and associated reticulation system is to enhance safe work practice
maintained and to not adversely disrupt the commercial Certification and recertification programmes to
equilibrium (including tariff). ensure competency of technical employees.
With the assistance of Akaun Amanah Industri New safe work procedure, enhanced permit to work
Bekalan Elektrik (AAIBE or Electricity Supply Industries Trust system, skill competition have been introduced
Account), TNB has taken the bold step to implement a Continuous audit, inspection and enforcement
live smart meter pilot project in Melaka and Putrajaya. activities to monitor non-compliance and at-risk
From this modest yet ambitious project, TNB will gather behaviour.
experience and know-how on smart meter (advanced Increase in promotional activities, safety campaign,
metering infrastructure) development, including related safety posters and leaflets
technologies and implementation which is one of the Disciplinary action against those who violate safety
critical enablers of Smart Grid and DG. rules and cause accidents
TNB is also embarking on numerous RE/DG projects
To address the issue with regards to equipment quality,
and plans such as biomass, solar facilities in the electricity
there is greater emphasis to ensure that only proven and
supply industry. This is in line with our commitment towards
tested products and technologies are utilised.
the national low carbon target.
TNB has established its own product certification
Distributed Generation has achieved significant
programme to prevent defective equipment from
progress recently due to the acceleration in technology
getting into our system.
evolution and emergence of Disruptive Technologies. TNB
Increased use of technology will reduce risks of
is of the opinion that new technologies require sustainable
accident e.g. Distribution Automation/SCADA, remote
and prudent learning growth in order to achieve the
switching, Regional Control Centre, switching robots,
most benefit without jeopardising the prevalent reliability,
modern switchgears, use cable spiker
security and economics of the electric supply industry (ESI).
Employees will be equipped with adequate testing
In developed countries, the electric supply industries
tools, earthing rods, arc flash suit and personal
are gradually shifting away from a linear supply value
protective equipment.
chain model that produces electricity from Generation,
transmitted over long distance through Transmission
infrastructure, and eventually distributed to respective What is TNB's role in promoting energy
loads on the consumer side at Distribution level. This eficiency in the country?
model will soon change with the advent of new Disruptive
Technologies that redefine the capability and economics Datuk Seri Ir. Azman: TNB has always been promoting
of smart grids, distributed generation, energy efficiency energy efficiency. Energy efficiency initiatives will benefit
and conservation, networking and connectivity. TNB, our customers and the nation. We will benefit in term
This evolution spawns new products and services of optimisation of energy transfer, which will enhance the
beyond keeping the lights on. Customers will have a efficiency of the electricity supply industry.
Apart from cost, supply reliability and energy security The programme is part of TNBs corporate strategy to
are prime factors that need to be considered seriously. empower and engage residential customers. Launched
Striking an optimal balance between these correlated in August 2015, it will involve about 200,000 households
factors has always been the prime objective for TNB in the Klang Valley, Negri Sembilan and Melaka. This
and the Government. In reality, fossil fuel as a resource, customer engagement programme is part of our latest
is limited and will become more expensive in the long efforts to enhance customer experiences and TNB will
term as it gets scarcer (although it is also affected by continue to strive further in developing and introducing
intermittent large fluctuation), the worlds population innovative and effective initiatives to enhance Malaysias
becomes larger and standards of socio-economic level Electricity Supply Industry.
increases. To date, TNB has carried out many energy efficiency
In line with the Governments policies, TNB believes initiatives aimed at educating and instilling awareness in
that the Energy Efficiency/Conservation should constitute the public culture and mindset. These initiatives are:
other fuel sources to help prolong the availability of Energy audits and consultancy at TNB and private
existing energy resources. Additionally, it will negate the buildings to improve energy efficiency and carbon
detrimental impact of the energy supply industry to the footprint.
environment by cutting down emissions. Training and certification to produce competent
TNB is supporting the 11th Malaysia Plan (RMK11) Energy Managers in order to fulfill the requirement in
which focuses on improving infrastructure and service Efficient Management of Electrical Energy Regulations
deliveries in ESI, via the implementing of specific strategies 2008 guidelines as set out by the Energy Commission.
that include better management of resources through Sponsoring Formula E 2015 as a platform to showcase
Demand Side Management and Energy Efficiency (EE) as how Electric Vehicles (EV) can change motorsport
well as addressing public communication. and the transportation landscape.
To promote EE, TNB uses various channels such as Home Energy Report (HER), a new programme
our own Kedai Tenaga and TNB website. Even our street launched in August 2015, utilises innvovation
furnitures have energy saving tips on them. We also meet analytics, behavioural science, and peer/neighbours
and share tips on energy saving with customers through comparison concept to motivate residential
dialogues, official visits, campaigns, exhibitions and consumers to implement energy saving practices.
education in schools.
Additionally, our subsidiary, TNB Energy Services Sdn. How committed is TNB to increasing the
Bhd., offers customers EE services which include energy percentage of Green Energy in the countrys
audit, retrofitting of energy efficient equipment, power electricity generation?
quality and power factor improvement as well as Energy
Performance Contract where the customers do not have
Datuk Seri Ir. Azman: TNB
to invest in upfront costs as this will be recovered from the
fully supports the Government
energy savings in their monthly bills.
initiatives to increase the
Currently, TNB is partnering with a third party, a global
percentage of Green Energy.
leader in the utility industry customer engagement
The governments target is to
programme, to launch a pilot customer engagement
programme, called Home Energy Report.
We are the first in the ASEAN region to implement
the Home Energy Report and the 3rd in Asia after TEPCO
(Japan) and CLP (Hong Kong). This pilot programme will
help customers to manage their energy use and save
money on their monthly electricity bills, using the concept
of similar peers/neighbours benchmarking.
have 2080MW of RE generation by 2020 and TNB plans to is also being conducted on the Integrated Gasification
contribute significantly towards this. Combine Cycle (IGCC) technology, Carbon Capture
Through our Distribution Division, we have opened our & Utilisation (CCU) technology etc. We have already
network and allowed connections of small scale RE plants established a pilot IGCC test facility at TNB Research
for RE developers participating in the Feed-in Tariff (FiT) (TNBR) as well as a pilot carbon capture plant using
scheme. To date, there are approximately 340MW of RE microalgae at the Manjung Power Station.
(FIT scheme) operating in the TNB network while another As for the challenges we are facing, most of these
540MW are in the pipeline under the FIT RE quota scheme. new technologies are relatively more expensive and we
With our experience in technical operations and our also need to build local expertise in these.
financial capabilities, we are pursuing joint-partnerships Malaysia is adopting an indicator of a voluntary (CO2)
for the development of RE plants, e.g. Amcorp Power reduction of up to 40% in terms of emissions intensity
(20MW Mini Hydro in Sungai Liang), Felda (12MW Biomass of Gross Domestic Product (GDP) by the year 2020 as
in Jengka) and Sime Darby (3.2MW Biogas in Tanjung compared to the 2005 level.
Malim and Kulai). We are constantly looking for new TNB is fully supporting the governments pledge by
opportunities to invest in RE and are keen to work with integrating low carbon technology in our conventional
both local and international partners. power plants, developing low carbon generation plants
TNB is committed to becoming a green utility company (RE) and promoting energy efficiency (EE) among
that embodies sustainability elements in its operation, customers. Our latest coal power plant in Manjung has
products and services. We are allocating Green Funds adopted the ultra-supercritical boiler technology, which
for the development of sustainability projects (including is up to 40% more efficient than conventional boilers
Green and RE projects) that benefit the nation and currently operating in Malaysia. Greater efficiency means
society. reduced use of coal and thus, lower carbon emissions.
We are also in the midst of reducing electricity
What are the initiatives that TNB has taken consumption in all our offices as we have retrofitted
to reduce carbon emissions? What are the these with EE equipment and installed solar panels on
challenges in this area? the roof tops. As part of our CSR programme, we also
installed solar panels on the premises of the Social Welfare
Department (Jabatan Kebajikan Masyarakat) to help
Datuk Seri Ir. Azman: The Malaysian Energy Industry
reduce its operating costs. The money saved can then be
is still largely dependent on fossil fuel (more than 90%
channeled to more critical operations.
predominantly gas, LNG and coal) for power generation.
Aside from that, our research arms (TNBR and Universiti
The options available are to invest in more efficient
Tenaga Nasional (UNITEN)) are exploring new low carbon
generating plants and to use the latest technologies to
technologies such as Carbon Capture & Storage (CCS)
mitigate the carbon emissions.
and gasification. TNB has also added low/zero carbon
TNB has conducted a study on carbon footprint for
generation plants such as 2 x 186MW Ulu Jelai Hydo,
the generation, transmission and distribution sector. This
265MW Hulu Terengganu Hydro, 12MW Chenderoh Hydro,
will provide a baseline reference in our future attempts
5.8Mw Tekai Hydro, 12MW Jengka Biomass, 20MW Sungai
to further reduce carbon emission. Various initiatives are
Liang Hydro and 3.2MW Tanjung Malim & Kulai Biogas.
being undertaken now in this respect.
We are also striving towards building capacity
For example, the deployment of the latest
and resources in the RE sector. TNB has accomplished
technologies, such as an ultra-supercritical power plant,
various achievements in conducting RE projects
will mean higher efficiency and less emissions. Research
and infrastructures that are currently dominated by
hydroelectric power generation and which commands
8.8% of total TNBs installed capacity equivalent to 1,911
MW. Apart from that, TNB also embarked on various local compete with property development which may offer
RE projects, such as: better value and returns comparatively. A solar power
Biomass 12MW JV project with Felda (Jengka, Pahang) plant is often classified as Distributed Generation,
Biogas 2 x 2MW JV with Sime Darby Plantation Sdn. hence location within the load vicinity is preferred to
Bhd. (Perak & Johor) reduce losses and raise system efficiency.
Demonstration project of Solar BIPV at Vibrant Caf Restrictive financing scheme. Financing frameworks
(120kW) and facilities are less supportive of RE development as
Project implementer for numerous rural electrification the industry is quite new.
projects (Solar Hybrid stations).
Some of the challenges TNB is facing in carbon emission How can IEM work with TNB to develop
reduction are: engineers who can contribute towards
High entry cost. This is one of the major barriers for new creating safe, smart and innovative power
technologies pertaining to Clean Coal Technology systems?
(CCT) and RE. However as technology matures and
impact of economic of scales, the cost is declining Datuk Seri Ir. Azman: TNB is always open to
towards commercialisation and grid parity. collaboration possibilities (e.g. joint training and
Striking an optimal balance between Cost Of Energy conferences) with all parties, including IEM, to further
and Economic Growth. As a developing country, develop engineers in the latest and innovative power
Malaysia requires significant amounts of energy to system technologies and know-how.
sustain and underpin the economic growth rate Within the TNB workforce are many experienced
at a reasonable and competitive tariff. At the and skilled engineers who are IEM members. In other
moment, fossil fuel is still the cheapest and most words, TNB is already a part of the IEM community and
reliable source of energy for fulfilling the criteria TNB professionals have regularly contributed to provide
in particular base load requirement although in insights, news and updated materials in IEM publications
the future, renewable energy will become more as well as at seminars and talks.
competitive. IEM can help to promote and disseminate TNBs efforts
Most RE resources are not suitable for serving base load. towards achieving safe, smart and innovative power
Since RE resources fluctuate, depending on daytime, systems, through the various media and communication
weather and climate, this poses uncertainty and channels.
reliability of power generation. Such a characteristic Inviting TNB engineers to share industry experiences
underpins the deployment of fossil fuel power plant to with IEM will enable its young engineers to gain a better
accommodate base load demand. understanding of the issues and challenges in order that
Location of RE infrastructures. Malaysia is blessed focus can be given to these areas.
with plenty of sunshine which compels the interest IEM can also work with the TNB Quality Assurance
and investment in solar power. However, solar power Team to share experiences and expertise that will ensure
generation still requires a big land bank size despite the quality and safety of equipment. IEM can also assist
technology advancement enhancing the efficiency equipment manufacturers to implement a safety system
of solar panels. Solar power generation also has to and product quality certification.
Malaysia made its commitment to liberalise ASEAN countries. Other international markets
Ir. Lai Sze Ching is currently its services in 1995 in the Uruguay Round of that Malaysian companies have penetrated
a Council member and an
EXCOMM member in IEM.
the WTO and through the ASEAN Framework include the oil and gas service sector,
He is the Vice-Chairman Agreement on Services (AFAS). In AFAS, education, aviation, health and professional
of Standing Committee ASEAN leaders gave their commitment to services.
of Examination and
Qualiication, Secretary of
liberalise the services sector completely by In April 2009 the government liberalised
the Standing Committee 2015 in line with the formation of the ASEAN another 27 services sub-sectors to strengthen
of Professional Practice, Economic Community (AEC). The AEC its economy and to face the increasing
Chairman of the sub-
committee on Amendment
enables freer trade in goods and services as challenges of globalisation. This was also in line
of IEM Constitution and well as transfer of expertise within the ASEAN with the governments objective to implement
the Chairman for the sub- member states. structural reforms in our economy. In this new
committee of Legislations
Affecting Engineering
Since the mid-1980s, a substantial amount economy model, the services sector will be
Profession. Ir. Lai is also a of liberalisation has taken place in the area developed intensively as the main engine of
committee member of the of international trade and services. Much of growth of the country.
Amendment of Registration
of Engineers Act under
this is inspired by WTO and various regional Subsequently, in 2011, the government
the Board of Engineers agreements. However, Malaysia is regarded announced that another 17 service sub-sectors
Malaysia. as being defensive in the GATS negotiations would be opened up and that 100% foreign
due to high level of protection of the services equity participation would be permitted in
markets. Nonetheless, Malaysias services offer those service sectors. These service sub-sectors
involved a wide coverage of sectors and included accounting and taxation services,
substantive bindings of current policies. Up legal services, architectural services and
to 2009, Malaysia had made commitments engineering services.
in 83 services activities, including both the Architectural and engineering services were
financial and non-financial sectors under scheduled to be liberalised by 2015, pending
GATS. The services sectors that were offered amendments to the relevant Acts. Once these
for liberalisation comprised business services, two sectors were liberalised, foreign equity
professional services, telecommunication participation up to 100% would be permitted.
services, marine services, audiovisual and Thereafter local engineering and architectural
broadcasting services, construction services, firms would have to compete with international
financial services, health services, tourism companies.
services, computer services, travel services,
rental and leasing services and entertainment AMENDMENT OF REGISTRATION
services. OF ENGINEERS ACT 1967 AND ITS
Malaysia has since acknowledged and REGULATIONS
viewed positively the benefits of the current The amendment to the Registration of
global liberalisation of the service sector. Many Engineers Act 1967 (Act 138) (REA) was finally
Malaysian companies have benefited from completed and passed by Parliament on 12
the global liberalisation of the sector and have February 2015 and came into operation on
successfully ventured into the global market. For 31 July 2015. The Registration of Engineers
example, in the construction sector, Malaysia Regulations 1990 was also amended and
companies are actively involved in various came into operation on 31 July 2015.
projects in the Middle East, India, China and
There are 2 papers in Part A and candidates must pass both papers in one
sitting. Paper 1 will have 40 objective questions and the time limit is 1.5 hours.
Paper 2 comprises 5 essay type questions, of which a candidate is required to
answer 3, within 1.5 hours.
The syllabi for Part A are:
PART B OF PCE
For Part B, candidates will sit for the paper in their discipline of practice.
The objective is to test a candidates competency in his field.
There are 2 papers in Part B and candidates must pass both papers in one
sitting. Paper 1 comprises 40 objective questions and the time limit is 1.5 hours.
Paper 2 comprises 5 essay type questions, of which a candidate is required to
answer 3. The time limit is 2 hours for Civil & Structure Engineering and 1.5 hours
for Mechanical and Electrical Engineering.
The passing mark for both papers is also 50%. The weightage of the topics is as below:
Mechanical
Air-conditioning and ventilation 40%
Fire protection 30%
Hydraulics 20%
Other mechanical systems 10%
Electrical
Regulatory practice 20%
The electricity distribution system 30%
System protection 25%
Building systems 25
The topics covered under Part B are very wide ranging and a candidate is
expected to understand and be familiar with all relevant technical knowledge
pertaining to general engineering practices such as building services,
infrastructure work etc.
I
n industry, an induction motor usually runs only at 50-60% loading conditions,
for two reasons. Firstly, it reduces the chances of overloading the motor and
minimises the thermal effect on the motor system. Secondly, the motor is
literally oversized to allow room for future expansion.
Ir. Dr Gobbi Ramasamy It is important to note that motors operating usually between 1% and 3.5% for a typical IE1
at 50-60% loading produces a relatively motor. Unfortunately, increasing the loading is
Ir. Dr Gobbi Ramasamy greater loss compared to those operating very subjective as it depends on production
is an associate professor at 75% loading (where optimum efficiency is line requirements. In practice this may prove
at Faculty of Engineering,
Multimedia University, Malaysia.
achieved). Besides, the power factor is also difficult to implement.
He is a consultant providing affected by the loading conditions. A bigger In order to minimise energy usage by the
solutions for problems
associated to electric motors
motor (e.g. 1kW) gives much better power motor system, the first option is to minimise
and drives system for various factor at full load and this is lowered gradually losses. For this reason, the existing load should
industries. He is also an Electric
Energy Manager Registered to
when load is reduced as shown in Figure 1. be increased and the motor should always run
Energy Commission, Malaysia, at 75%. Increasing loading from 50% to 75%
and a Senior Member, IEEE.
makes the motor operate at higher efficiency,
usually between 1% and 3.5% for a typical IE1
motor. Unfortunately, increasing the loading is
very subjective as it depends on production
line requirements. In practice this may prove
difficult to implement.
The next option is to consider high efficient
motors (HEMs), that is IE2 or IE3 motors. It is
stated in MS1525:2014 Energy efficiency and
use of renewable energy for non-residential
Figure 1: Power factor under various loading conditions buildings - Code of Practice (second revision),
that only IE2 or IE3 motors shall be used
If a smaller motor (e.g. 0.75kW) is used, the
based on economic justification basis. IE2
power factor is much lower. When the motor
motors give higher efficiency, typically from
runs at a lower power factor, the motor draws
6% (for 0.75kW) to 1% (for 200kW and above)
a higher current to produce the required
whereas IE3 motors give 10% (for 0.75kW) to 2%
mechanical power. Higher current means
(for 200kW and above) as compared to IE1
higher copper losses in the cable and motor
motors. Accordingly, at lighter loading
windings. The relationship of these parameters
conditions, IE2 and IE3 motors have a higher
is shown in equation 1, where I is the line current,
efficiency than IE1. But the issue is the initial cost
Pm is the mechanical power which is constant
of changing to HEMs.
for a given load and speed, PL is the rotational
Figure 2 shows the comparison study
and copper losses. V is the supply voltage
between IE1 and IE2 motors over three years
which is constant, cos is the power factor.
of operations for motor rating of 15kW to 75kW.
The initial cost of IE2 is 80% higher than IE1 (price
(1) quoted by suppliers in Malaysia). However,
based on savings in energy cost by using IE2
In order to minimise energy usage by the motors, it has been found that this cost can be
motor system, the first option is to minimise recovered in under 3 years. The energy cost
losses. For this reason, the existing load should calculation is based on 50 sen per unit for 3,600
be increased and the motor should always run hours of motor operation annually.
at 75%. Increasing loading from 50% to 75% Amid concerns over the initial cost of
makes the motor operate at higher efficiency, HEMs, most companies opt to rewind faulty IE1
starting) so that starting current peak is reduced. This can be a solution to avoid
high maximum demand charges.
On the other hand, variable speed drive (VSD) controls both the speed
A Nehemiah Group of Companies and torque throughout the motor operations (starting, constant/variable
Formerly Neusynthetics Sdn. Bhd.
loading, and stopping). Generally, a fixed voltage, fixed frequency AC
We are a supplier of high quality source is converted to a DC source by using an arrangement of diodes and/or
geosynthetic products used for soft soil insulated gate bipolar transistors (IGBTs). This process is called rectification. The
stabilization, slope reinforcement, coastal
erosion protection, river bank protection,
DC source is then smoothed by a group of capacitors. The smoothed DC source
landfills, drainage, road and railway is converted to a variable voltage, variable frequency AC source using an
construction. inverter with an arrangement of IGBTs. VSD controls power to the motor based
Our Products: on load requirement, so this is a better solution for saving energy, especially for
motor systems running at variable speed and under variable load conditions.
NEXTILE NON-WOVENS
Unfortunately, most old VSDs use a diodes arrangement for rectification
NEXFORCE HIGH-STRENGTH WOVENS process. This produces current harmonics at the source which will affect the
NEXGRID GEOGRIDS
power factor of the power system and directly contribute to energy losses in
electrical equipment. To minimise this, a passive filter should be installed to
We also provide design, specification, bill of minimise the harmonics level to within the IEEE 519 requirements.
quantities, cost estimate and drawings
free-of-charge. With significant changes in our local climate, afternoon temperature
can reach as high as 36C [3] compared to 34C reported 17 years [4] ago.
In addition, the high humidity, reported within 70% to 90%, also creates an
uncomfortable atmosphere at work for people and equipment. So it can be
expected that, without proper ventilation, electric motors and systems will
overheat. The hot spot in a motor is actually a combination of motor design
(temperature rise) and the ambient (surrounding) temperature. As 50% of
motor loss comes from copper loss, cooling of the motor is essential to minimise
insulation failures. Besides, when self-cooled motors run at lower speed with
VSD, the cooling effect will be lower and this can result in overheated motors.
Adding force cooling fans may solve this issue. In fact when the motor is
connected to VSD, the location of VSD is very crucial. The IGBT at the VSD
operates typically at 4 kHz switching high current and this produces excessive
heat and transfers heat to the heat sink. The ventilation at the heat sink ensures
the transfer of heat to its surroundings. Improper ventilation will trigger the
temperature sensor at the heat sink and trip the VSD. Moreover, the hot heat
sink will reduce the life cycle of IGBTs.
CONCLUSION
There are four basic issues to tackle to minimise the electricity bill for motor
systems:
1. To manage the motor load
2. To improve power factor at the motor
3. To minimise current harmonics at the supply point of variable speed drive
4. To provide proper ventilation for motors and variable speed drive systems.
In addition, for greater savings, opt for IE2/IE3 motors rather than rewinding or
purchase of new IE1 motors, should there be a need to replace the motors.
I hope the list is helpful to you to search for the older articles. We will resume the regular column in the coming issues.
Share your thoughts on what you would like to read or share: pub@iem.org.my.
Every journey should also have a destination so that we know where it ends!
IEM DIARY OF EVENTS Title: Technical Visit to Boustead Shipyard and Royal
Malaysian Navy Base, Lumut
Title: 2-Day Course On Contract Management for
26 - 27 February 2016
Construction Projects Organised by : Project Management Technical Division
22 - 23 February 2016 Time : 7.00 a.m. 5.00 p.m.
Organised by : Project Management Technical Division CPD/PDP : 5.5
Time : 8.30 a.m. 5.30 p.m.
CPD/PDP : 14 Title: Talk on Malaysians First Hydrodynamic Marine
Laboratory
Title: Talk on Approval Processes and Technology 3 March 2016
Transfer Particularly On Rolling Stocks Organised by : Marine Engineering & Naval
25 February 2016 Architecture Technical Division
Organised by : Mechanical Engineering Technical Time : 5.30 p.m. 7.30 p.m.
Division CPD/PDP :2
Time : 5.30 p.m. 7.30 p.m.
CPD/PDP :2 Kindly note that the scheduled events below are subject to
change. Please visit the IEM website at www.myiem.org.my
for more information on the upcoming events.
T
he IEM & IET Electrical Conference 30 NOVEMBER: TUTORIAL SESSION
2015 at Sime Darby Convention Centre The first speaker, Ir. Assoc. Prof. Dr Gobbi
gathered more than 150 participants, Ramasamy, an associate professor in the
including local and overseas experts. This Faculty of Engineering, Multimedia University,
is the third IIEC, jointly organised by the Malaysia, presented a tutorial on Motor
Electrical Engineering Technical Division And Drives. Dr Gobbi started with a brief
(EETD) of The Institution of Engineers Malaysia introduction on the relationship between motor
(IEM) and the Institution of Engineering and and pumps, and the generation of flow while
Technology (IET), Malaysia Network. The IIEC determining the power output and types of
reported by
Ir. Ng Win Siau has been held biannually since 2011. losses. He explained that with motor efficiency
of only about 30% at light load, Variable Speed
Ir. Ng Win Siau graduated
Drives (VSD) offers a significant reduction in
from the National University
of Singapore in Bachelor of losses, bearing in mind that each unit loss in
Engineering and a Master
motor output is equivalent to about 3 unit loss in
of Engineering in Electrical
Engineering. He is currently energy production cost.
an electrical engineer with
He then introduced High Efficiency Motors
Perunding MM 20-20 and
a committee member of (HEM), describing the efficiency classes
EETD.
under the international standards. In the
examples he showed, the higher efficiency
class entailed higher initial costs but showed
Deputy President Ir. Tan Yean Chin visiting the technical a significant amount in energy costs saved
exhibition accompanied by Ir. Yau Chau Fong
during the lifespan of the motor, with potential
payback within 2 years. He highlighted the
This year, the conference theme was low uptake of HEM in a Malaysian market
Safe, Smart and Innovative Development study largely due to challenges in convincing
in Power Systems, in line with the nations the decision makers considering the low
push for enhancing safety in electrical supply electricity tariff and unregulated price of
and usage, improving energy efficiency with HEM.
technology and the effective adoption of While encouraging the use of VSDs,
renewable energy sources. The conference Dr Gobbi cautioned on the need for the
provided a platform for participants to proper implementation of VSD while sharing
stay updated on the latest trends and its typical practical issues. The production
technologies in the industry, and for experts of undesirable power harmonics by the
to gain valuable feedback on the industry DC Link in VSD, the effects of power
requirements. harmonics including overheating, power
A one-day tutorial session was held factor reduction and bearing current, and
on 30 November 2015 while the two-day a comparison of the harmonics mitigation
conference was held on 1-2 December, methods were discussed. Also discussed
2015. Throughout the 3 days, there was an were parameter settings without good
exhibition where companies showcased their understanding of motor physical limitations
safe, smart and innovative solutions. and equipment location choice, considering
fund. NEM allows electricity consumers to install PV systems He presented the statistics of electrical accidents in
for self-consumption, with the balance being exported to Malaysia, which he believed was important to gauge the
the grid, and net-off from their monthly bills at displaced situation. Although the number of reported accidents
cost. USS allows PV plants with capacity less than 50MW to since 2002 showed a slight upwards trend, the rate of
be selected through open biding and connected to the casualty per million consumers was a declining and
distribution or transmission network. stabilising trend. Nevertheless, he added, we need to
constantly look into minimising electrical accidents.
1 DECEMBER 2015: FIRST DAY OF CONFERENCE He said major causes of accidents were improper
In the opening ceremony of the IIEC 2015, Ir. Dr Matthew installation and maintenance as well as non-compliance
Teow Yok Wooi, Chairman of The Institution of Engineering to safety work procedures, with a majority of the
and Technology (IET), Malaysia Network gave the first accidents occurring in utility installations. The Residual
welcome address. He reiterated the long solid partnership Current Devices (RCD) showed that the highest number
with IEM and thanked IEM, especially the organising of accidents involved electrical appliances, hence the
committee, for the support in delivering the event, stringent equipment testing requirement imposed. He
bringing in experts from various technical fields. He then also highlighted the disparity between the large number
shared the history of IIEC since 2011 and highlighted the of certificate of competency issued and the low number
strong relevance of the theme of IIEC 2015: Safe, Smart of registered competent persons in the workforce.
and Innovative Development in Power Systems. As a way forward, strengthening of the regulatory
The next welcome address was by Ir. Tan Yean Chin, framework, enhancement of enforcement activities,
Deputy President of The Institution of Engineers Malaysia increasing awareness of safety and promotion of high
(IEM). He congratulated EETD and IET for jointly organising voltage training centre were some of the key initiatives
IIEC 2015 and said IIEC is a forum for practicing engineers taken by the Energy Commission.
to discuss safety issues. He stressed that engineering was The first session with the sub-theme, Electrical
the key component in building the energy infrastructure. Safety, was chaired by Mr. Murugiah Suppiah. The first
Finally, he thanked the sponsors and declared IIEC 2015 speaker was Dato Ir. Jimmy Lim Lai Ho, CEO of Tokai
officially opened. Engineering (M) Sdn. Bhd., who presented on MS IEC 62305
The first keynote speaker on the topic Electrical Lightning Protection Standard Overview and Lightning
Safety in Malaysia was Ir. Mohd Elmi bin Anas, Director of Safety Management of Personnel and Equipment. He
Department of Electrical Safety Regulation, Suruhanjaya said Malaysia ranked second in the world for lightning
Tenaga Malaysia, representing Datuk Ir. Ahmad Fauzi bin activity, with an average of 2.59 million strikes per year.
Hasan, CEO of Suruhanjaya Tenaga Malaysia. Ir. Mohd Elmi He pointed out a high profile incident, the 2009 collapse
explained the roles and function of the Energy Commission, of Putrajaya Hospital wall due to lightning, as the catalyst
stressing on the protection of the public from dangers arising for endorsement and approval of MS IEC 60325. He then
from the supply and use of electricity as provided for under spoke in detail about the 4 parts of the MS IEC 60325
the electricity supply laws. He said the recent amendment before highlighting the major differences between BS
to the Electricity Supply Act, 1990 was gazetted on 5 6651 and the MS IEC 62305, and the concept of Lightning
November 2015 and was awaiting enforcement. Safety Management for Open Areas.
The second speaker, Ir. Mohd Elmi bin Anas, presented
Electrical Safety from a Regulatory Perspective. He
talked about the latest amendment to the Electricity
Supply Act, 1990, aimed at achieving a reliable
and affordable electricity supply for our economic
development towards being a developed nation by 2020.
The amendments were categorised into four objectives:
To enhance governance of the industry, to improve safety
practices, to protect consumer interests and to enable
more effective enforcement.
The third speaker, Ir. Lim Kim Ten of Hager Engineering
(M) Sdn. Bhd. presented on the topic, Household
Electrical Protection, which encompassed the parties
involved and responsible, the types of electrical faults
and circuit breaking devices, and a detailed overview
of the Residual Current Devices (RCD) and the wiring
regulations.
Datuk Ir. Baharin bin Din, Vice President (Distribution),
Tenaga Nasional Berhad presented the second keynote
Ir. Mohd Elmi, Director of Department of Electrical Safety Regulation, address on Energy Efficiency and Management. He
Suruhanjaya Tenaga Malaysia started by describing sustainability challenges, including
Third keynote address by Ir. Prof. Academician Dato Dr Chuah Hean Teik
maintenance costs, break even occurred at distances Small Hydro Power Scheme Under The Renewable Energy
above 800km or submarine links above 50km. He described Programme. There was a large jump in small hydro power
the components in the HVDC system and TNBs HVDC of 10-30MW capacity in approved projects for 2016. Ir. Khor
experience at the 300MW 300kV DC Malaysia-Thailand described the technical feasibility, economic viability and
interconnection, which allowed the sharing of spinning legal requirement studies prior to the licence application
reserve between TNB and EGAT and alleviating multiple with the example of the Mini Hydropower Scheme in Way
major power trip incidents. HVDC development continued Malaya, Lampung Province, Sumatera, Indonesia. He
on Ultra High Voltage Direct Current 800kV design with highlighted common issues and risks involved, from feasibility
power capacity exceeding 5000MW on a single system, the studies to construction and final operation, one of which was
shift towards use of Voltage Source Converters and Multi- the lack of stream flow records to predict power generation.
terminal HVDC designs for HVDC grids. The fourth speaker, Prof. Dato Ir. Dr A. Bakar Jaafar,
The third speaker was Ir. Dr Amir Basha Ismail of Professor at UTMs Perdana School of Science, Technology,
Minconsult Sdn. Bhd., who spoke on Malaysias Electric Innovation and Policy, spoke on Ocean Thermal Energy
Railways: A Systems View. He talked about the history of - H2 Fuel Cell Renewable Energy Mix in Electrical Power
electric railway in Malaysia, beginning primarily with the Generation in Malaysia. Ocean Thermal Energy (OTEC)
Light Rail Transit (LRT) and KTMB train systems. The electric converts part of the heat from the sun which is stored in
train system, comprising infrastructure, rolling stock and the surface layers of a body of water, into electrical energy
system of operating procedures, required more than just civil or energy product equivalent such as hydrogen, H2. Prof.
and structural engineering skills. Currently, a local electrical Abu Bakar spoke about the barriers of the technology
graduate has minimal knowledge of an electrical train and ways to overcome the challenge including the use of
system, traction power system, train control and signalling and project life costing to overcome the high initial capital and
operation software integration. Dr Amir Basha elaborated the reference to Territorial Sea Act and Exclusive Economic
on the traction power system and the fundamentals of train Zone Act to govern the development of OTEC in the sea.
propulsion, giving examples from KTMB 25kV AC Klang Valley He shared plans for the first public funded OTEC project
traction power system and Prasarana/RapidRail DC traction off Pulau Layang-Layang under the 11th Malaysia Plan, to
power systems. supply power to deep water oil and gas production, the
The final session with the sub-theme, Renewable surplus of which to generate H2.
Energy, was chaired by Prof. Ir. Dr Vigna Kumaran. The fifth speaker, Dato Ir. Muhamad Guntor Mansor
The first speaker was Encik Thariq bin Husni of MTS Green Tobeng, Managing Director, Gading Kencana Sdn.
Energy, who presented The Present and the Future of Wind Bhd., presented on Powering the Economy with Solar
Turbine Technology in Malaysia. First, he asked participants Technology. First he spoke on government policies that
if there was sufficient wind in Malaysia. Then, he gave a brief helped the PV take-up in Malaysia with a target of 1.25GW
history of wind turbine and its design considerations, such capacity by 2020. He shared his experiences in the various
as height of tower and propeller diameter, with a focus of projects implemented, elaborating on the restrictions of the
existing installations in Malaysia. Wind technology remains a actual available land area due to land use requirements,
challenge due to the lack of data on potential wind area study of shadow casting and sun path considering the land
and insufficient incentives or confidence for its development. terrain and the use of PV roof in aiding the cooling of the
The second speaker was Dr Thomas Riendl, Deputy CEO, building.
Cluster Director, Solar Energy Systems, Solar Energy Research The sixth speaker was Encik Sansubari Che Mud,
Institute of Singapore (SERIS), NUS, who presented on Future Renewable Energy, Tenaga Nasional Berhad (TNB) who
Trends in Solar PV. He shared data on how the global Photo spoke on TNB Renewable Energy Guidelines. He described
Voltaic (PV) market hadboomed very quickly, with 40GW the implementation of the FiT scheme, defining the scope
added in 2014 alone. The statistics showed that each time of TNBs role based on the capacity of the project and the
the cumulative production doubled, the PV module price status of projects in progress. With remote meters already
went down by 20%. He said that solar cell efficiency was 18- implemented, in the bid to enhance customer experience,
23%, with only a marginal increase of about 0.5% each year. TNB is implementing projects to allow checking of RE account
On the other hand, the PV system design, if not designed online, comparing self-consumption for the Net Metering
properly, could cause a large variance in the overall power scheme to be implement from 2016.
output. Variability and uncertainty remain the two main
challenges of PV systems penetration in electricity grid, CONCLUDING REMARKS
prompting the need for PV power forecasting, optimised The conference came to a close with Chairman of EETD,
PV location planning and PV potential analysis. Dr Riendl Ir. Yau Chau Fong expressing his gratitude and thanks to
spoke about the Levelised Cost of Energy (LCOE), which the organising committee, the conference secretariat
was critical for economical feasibility study of a Solar PV staff and the participants for contributing to the success
implementation. of the event. Ir. Yau and the organizing commitee looked
The third speaker, Ir. Khor Chai Huat, Managing Director forward to meeting all the delegates again in the next IIEC
of Angkasa Consulting Sdn. Bhd., presented on Viability of in 2017.
T
he term Smart Grid does not refer to a modernisation covering the whole spectrum
specific technology. It is an aggregate term of electric grid, from power generation at one
that encompasses a set of technologies in end to the consumer at the other. Through the
modernised electrical network. Through Smart inclusion of Smart Grid technologies, the grid is
Grid, we can achieve greater efficiency in able to provide real time feedback and hence
the system, save money and help reduce CO2 becomes more flexible, interactive and reliable.
emissions. Prof. Hew discussed briefly the six IEC White
The Electrical Engineering Technical papers:
Division (EETD) organised a pre-AGM talk titled 1. Orchestrating infrastructure for sustainable
reported by
Is The Grid Smart?. It was delivered by Prof. Dr smart cities
Ir. Lee Cheng Pay
Hew Wooi Ping and chaired by EETD Chairman, 2. Internet of things: Wireless sensor networks
Ir. Lee Cheng Pay Ir. Yau Chau Fong. 3. Micro grids for disaster preparedness and
received his Bachelor recovery, with electricity continuity plans
Degree in Electrical DEVELOPMENTS
Engineering from and systems
Universiti Malaya and Prof. Hew reviewed several major power 4. Grid integration of large-capacity
Master in Engineering outages in Northeast US, Italy and India that
Management in Universiti renewable energy sources and use of large-
Putra Malaysia. He is affected millions of people and led to the capacity electrical energy storage
the Director of Duriane development of Smart Grid. 5. Electrical energy storage
Consult Services.
The Smart Grid initiatives started with IEEE 6. Coping with the energy challenge.
Smart Grid Standard development in 2007. IEC
The future power system as suggested is shown
formed Strategic Group (SC) 3 to work on Smart
in Fig 1.
Grid Standard in 2008. Beside the effort by IEEE
Some questions were raised from the
and IEC, several countries also started their own
audience. A participant asked whether the
initiatives.
carbon emission can be consistently reduced
China Smart Grid Initiatives has set a target
despite the increase in energy utilisation.
to reduce carbon emission per unit of GDP to
Another participant asked about consumers
40-45% of the 2008 level by 2020. United States
role in deciding on generation and transmission
Smart Grid Initiatives focuses on maintaining a
of energy.
secure and reliable electricity infrastructure by
In conclusion, Prof. How suggested that
using smart technology. Japan Smart Grid
Malaysia should refer to EU as a benchmark
Initiatives 2009 aims to develop a low carbon
on the carbon emission level per GDP,
society to reduce carbon emission to 75% of the
consumer participation scope, and post-fault
1990 level or two-third of the 2005 level by 2020.
reconfiguration capabilities.
SMART GRID DRIVERS
The smartness of the grid is
measured in term of carbon
emission, active consumer
participation in energy
management and intelligent
post fault configuration to avoid
cascaded faults, said Prof. Hew.
He quoted from IEC on Smart
Grid that Smart Grid drivers
include ageing infrastructure,
integrating intermittent energy
sources, lower energy price and
security of supply and increasing
energy need, sustainability and
challenges faced by utility.
In effect, Smart Grid is Figure 1: Suggested future power system (IEC White Paper: Coping with the
a concept of electric grid energy challenge)
C
onsumers have rights and the body The group then proceeded to the air
entrusted to safeguard the safety and delivery room. This was where the air delivery
efficiency of household electrical, performance of ceiling fans and standing
electronic appliances and communication electric fans were measured and compared
devices sold in Malaysia is SIRIM QAS against the electrical power consumed. This
International, a subsidiary of SIRIM Berhad. automated test was part of the performance
The Electrical Engineering Technical Division and energy efficiency test.
(EETD) arranged a technical visit to the SIRIM The group was then visited the wiring
reported by QAS International facilities in Shah Alam, which accessories testing lab where the group saw how
Ir. Amir Hussein bin Jaafar was spread over two days (17 November and switches, wall plug and sockets were subjected
15 December 2015). Only a section of the tests to endurance testing through the continuous
Ir. Amir Hussein bin
showed to the party is reported herein. switching on and off of the appliances. The
Jaafar graduated from
Universiti Technologi On the first day of the visit, SIRIM QAS appliances were all rigged to test machines and
Petronas (UTP) with International senior general manager, Puan Nur test executions and result data gathering and
Bachelor Engineering
(Electrical and Electronics) Fadhilah, gave the 16 IEM visitors an overview analysis were all automated.
and from Universiti briefing. She clarified that while all household
Teknologi Malaysia (UTM) ENERGY EFFICIENCY LAB
with Master Science appliances sold must be certified by SIRIM QAS
During the second visit on 15 December, the
(Real Time Software). International, the regulatory institution under the
He has over 14 years of group went to SIRIM QAS International Energy
experience in automotive law is Suruhanjaya Tenaga, Malaysia.
Efficiency Laboratory in Seksyen 16, Shah Alam.
electrical and electronics.
He is currently Head of
TESTING SERVICES Here, the tests conducted were to rate
Design and Development
Three types of testing service are available: electrical appliances under the Energy
Engineering with Eco
Motive Sdn. Bhd.
1. Mandatory certification, which includes Efficiency and Energy Labelling programme. In
safety tests, performance tests and energy one of the test labs, the personnel demonstrated
efficiency tests how household air conditioner performance
was measured when the appliance was set
2. Voluntary testing, which includes product to maintain specific temperature decreased
conformity to manufacturers requirement or within a specific air volume and then compared
national and international standards and against the electrical power it consumed.
3. Market surveillance, which includes auditing In the next test lab, refrigerator performance
the market for appliances already granted was measured where the appliance was set to
the SIRIM label. maintain a specific internal temperature and
then compared against the electrical power it
VISIT TO DOMESTIC PRODUCT TESTING LAB consumed.
A test personnel explained that the lab was In another test lab, household lamps and
equipped to carry out tests on 34 types of ballast performances were measured. In a
household appliances such as boiler, washing test equipment called integrating sphere, the
machine, water heater, refrigerator, fan, total light radiation of lamps was measured
oven, rice cooker, iron, and power tool. These and compared against the electrical power
appliances must pass the prescribed safety tests, consumed. Test personnel also demonstrated
according to IEC Standard 60335. how a photometer was used to measure the
During the visit, the personnel demonstrated light intensity.
a temperature rise test on a refrigerator It was a good learning experience for the
and an endurance test on a water heater. members who took part in the visit. SIRIM QAS
The personnel then performed the primary and International is the consumers line of defence
secondary suspension tests on a ceiling fan while with regards to the safety of household electrical,
it was stationary and while in operation. The electronic appliance and communication
drop test on an iron was also conducted. devices sold in Malaysia. n
34 JURUTERA February 2016
FORUM
T
he 7th AGM of eETD, attended by 17
members, was held at the IEM Penang
branch office on 10 October, 2015.
Chairman Ir. Bernard Lim Kee Weng
delivered the welcome speech and thanked
all the members who were present, especially
those who had come all the way from Miri
and Kuala Lumpur. He expressed his gratitude
to his committee members for their support
reported by
Ir. Dr Lee Choo Yong and hard work in organising various activities
which benefitted IEM members and cultivated
Ir. Dr Lee Choo Yong is engineering innovation in undergraduate
a committee member of
Electronic Engineering students. Second row (left to right): Ir. Dr Khor J.G., Ir. Dr Mui K.Y.,
Technical Division (eETD). During the AGM, the election of committee Ir. Sivarama R., Engr. Dr Huzein F.H Grad. IEM., Ir. Dr Lee
C.Y., Engr. Tiong T.C Grad. IEM., Engr. Dr Chang B.P Grad.
members for 2015/16 was held. Engr. Dr Leow IEM., Engr. Dr Wong Y.H. Grad. IEM
Cheah Wei was announced by Ir. Bernard Lim First row seated (left to right): Ir. Bernard Lim K.W.,
as the new eETD Chairman. The new committee Ir. Bhuvendhraa R., Engr. Dr Leow C.W Grad. IEM.,
Engr. Lau H.K. Grad. IEM.
members are as listed below:
It was a great achievement that eETD
Engr. Dr Leow Cheah Wei
Chairman recorded a substantial increase in the number
Grad. IEM
of members from 126 the previous year to 607.
Vice Engr. Lau Heng Kar Membership breakdown as of 30 September
chairman Grad. IEM
2015 as shown:
Honorary
secretary Membership Numbers of Members in
Ir. Bhuvendhraa Rudrusamy
cum grade eETD
treasurer
Fellow 2
Committee Engr. Dr Chang Boon Peng
members Grad. IEM
Senior member 1
Engr. Dr Huzein Fahmi Hawari
Grad. IEM
Member 138
Ir. Dr Khor Jeen Ghee
Student 88
Advisor Ir. Bernard Lim Kee Weng
There were 14 committee meetings Microsoft, National Instrument and Silterra. The eETD has
held from August 2014 to October 2015. been participating in Innovate Malaysia Design Competition
The eETD organised 9 technical talks, delivered by since 2010. This award is open to all final-year undergraduate
distinguished scholars and/or engineers worldwide. Many engineering and computer science students in Malaysia to
of the talks were held in Universiti Sains Malaysia (USM) to promote innovation culture and mindsets among university
facilitate convenient participation of engineers working graduates, to enhance knowledge and skills set in practical
in Bayan Lepas industrial zones. Technical talk details are engineering and to promote greater interest in engineering
shown in the table below: design, and to promote more industry and university
collaboration. The award was won by Yiauw Diing Shenq
Date Title Speaker and Wee Hin Sheik from USM with their paper titled
Development of Add-On Active Vibration Control
Splitting our (computer)
Dr Shawn Tan (AVC) for Power Tools (https://www.youtube.com/
8 October brains: Multi-processor,
(Independent watch?v=8c4GN2zP14E).
2014 Multi-core and multi-
consultant) Penang Maker Faire, organised by Collaborative
threads
Research in Engineering Science and Technology (CREST),
3 Meemusari was held together with Penang Science Fair in Spice
Catalyse business
December (Independent Arena on 15-16 November, 2014. It was sponsored by Intel,
development
2014 consultant) National Instruments, Penang Science Cluster, Koridor Utara
16 Breaking the 3D power Prof. Dr Mircea R. Malaysia and Silterra. The eETD supported this event to
December delivery wall using Stan, University of promote makers culture and 10 student members of eETD
2014 voltage stacking Virginia participated in the event.
A dialogue with USM on 25 November, 2014, was
Design and verification Cliff Cummings
16 January another initiative by IEM Penang branch and eETD to drive
techniques using system of Sunburst
2015 student membership recruitment and foster collaboration in
Verilog Design Inc.
training activities, engineering career talk and route to be
Prof. Wendy Hall professional engineers. Deputy vice chancellor (industry and
13 March The internet, the web and
of University of
2015 the future of everything community network) Professor Dato Dr See Ching Mey led
Southampton
the USM team to support this important dialogue. The result
Prof. Dr Andrew was the significant increase in eETD student members.
13 April Business development in Richardson, The eETD committee, under the leadership of Ir. Bernard
2015 multi-disciplinary enablingMNT Lim, has brought it to the next level, resulting in IEM being
(United Kingdom) recognised by engineering fraternities and academic
Prof. Dr Tan Cher institutions as the professional body for promoting science
25 June Electromigration
Ming, Chang and technology advancement, particularly in electronic
2015 simulation at circuit levels
Gung University engineering in Penang, the Silicon Valley of the East.
A review pertinent to
Prof. Dr Chao-
26 June next generation RRAM IEM DIARY OF EVENTS
Sung Lai, Chang
2015 (Resistive Random Access
Gung University Title: Half Day Seminar on Smelly Toilets Why,
Memory) reliablity
Where, What, Who, When and How To Eliminate
Prof. Hsueh-Ming
2 04 Mar 2016
Technology and standard Hang, National
September Organised by : Building Services Technical Division
for virtual-view 3D systems Chiao Tung
2015 Technical Division
University Time : 9.00 a.m. 1.00 p.m.
CPD/PDP : 3.5
The eETD also endorsed NEPCON Malaysia held in Spice
Arena, Penang, on 9-11 June 2015. On the other hand,
Title: 18th Annual General Meeting of Information
eETD also contributed to CAFEO 33 by inviting speakers
and Communications Technology Special Interest
from electronics multinational companies to participate.
Group
The eETD co-organised an embedded system workshop
with IEEE Nottingham University Malaysia Campus student 05 Mar 2016
Organised by : Information and Communications
branch. This workshop gave students good exposure to
Technology Special Interest Group
microprocessor platform so that they would be better Time : 11.00 a.m. 1.00 p.m.
prepared when entering the industry. CPD/PDP :2
The eETD also continued to sponsor the IEM Best
Paper Award worth RM1,500 of Innovate Malaysia Design Kindly note that the scheduled events below are subject
Competition 2015, organised by renowned technology to change. Please visit the IEM website at www.myiem.org.
companies like Altera, CEDEC, Intel, Keysight, Mathworks, my for more information on the upcoming events.
T
he Civil and Structural Engineering
Technical Division (CSETD) recently
organised a technical visit to Lafarge
Construction Development Lab (CDL) Petaling
Jaya. There were 40 participants, comprising
student members, academicians and
practitioners.
On arrival at CDL, the participants were
welcomed by a Lafarge staff member
reported by who gave a safety briefing, followed by a
Ir. Dr Ng Soon Ching
presentation on the background of Lafarge
Ir. Dr Ng Soon and an introduction to CDL. According to
Ching graduated her, CDL is the fifth in the world and the first
with BEng (Civil) and
MSc (Construction
in Southeast Asia which aims to promote
Management) from construction efficiency by adapting innovative
Universiti Teknologi solutions to better meet our construction and
Malaysia (UTM) and PhD
(Engineering) from UTAR.
building needs.
He is currently the Deputy CDL houses three labs (cement, concrete
Chairman in the committee and aggregates and soil labs) which are Demonstration on SCC at Concrete and Aggregates Lab
of IEM CSTD.
equipped with state-of-the-art testing of finishing, i.e. without surface treatment and
equipment for quality control and assurance of with surface treatment of exposed aggregates
its products. It also has an open testing area for method.
prototypes and demonstrations of new building In the lab tour section, CDL houses three
systems and structures. labs: Concrete and Aggregate Lab, Cement
After the briefing, the participants were Testing Lab and Soil Lab.
divided into two groups for a tour of the labs The Concrete and Aggregate testing
and testing area. They were ushered to the two lab is equipped with 3-layer curing tank and
model houses, concrete pavement, cement refrigerated bath circulator, coring machine,
reported by lab, concrete lab and finally soil lab. Methylene Blue Test (MBT), in addition to
Engr. Wong Ai Ming One of the model houses was constructed the usual compression and flexural test
Grad.IEM
using the conventional method and the equipment. MBT is used to assess the quantity
other was constructed using monolithic of potentially harmful fines in fine aggregates.
Engr. Wong Ai Ming
building system which engages the use of an A demonstration on the SCC was conducted
graduated from Monash
University, Melbourne, with aluminium formwork, with the spaces filled during the visit.
a Bachelor of Materials with Self Compacting Concrete (SCC). The The Cement Testing Lab is equipped
Engineering (Hons).
whole process of construction takes four days, with lab oven, mini ball mill, Rapid Chloride
Engr. Wong is the from the installation of vertical rebars and wall Permeability Test Equipment (RCPT) and a full
Construction Specialist formwork, installation of horizontal rebars and range of EN mortar testing equipment. The lab
of Lafarge Malaysia Bhd.
deck formwork, M&E, formwork alignment and officer explained and showed us the RCPT. The
and currently a committee
member of CSTD division. filling of Self Compacting Concrete to the final Soil Lab is equipped to test California Bearing
removal of the formwork. Ratio (CBR), plastic limit of soil, and Unconfined
The next stop was the car park which was Compressive Strength (UCS).
constructed using both coloured concrete and After the tour, there was a Q&A session,
pervious concrete. The latter allows the flow of during which the visitors could seek further
water into the ground and reduces ponding. clarification to their queries. Then, the Chairman
Adjacent to the car park were 2 concrete of CSETD, Ir. Hooi WC, presented a memento of
pavements, JPCP (Jointed Plain Concrete appreciation to Lafarge at the end of the Q&A
Pavement), and RCC (Roller Compacted session. It was certainly an informative visit to
Concrete). Both were constructed using 2 types the group.
reported by
Ir. Hor Kok Luen
W
hat is a boiler? A boiler is a piece of The presentation included the following
machinery that heats water inside aspects of boiler systems:
it to boiling point. The water can 1. The location of pressure containing
be used for water heating, central heating, principal components (steam drum, water
boiler-based power generation, cooking and drum, superheater, front headers, side
sanitation purposes. headers, tubes and integral piping)
To learn more about boilers, the Agricultural
2. The process flow of steam drum and water
& Food Engineering Technical Division (AFETD)
drum
of IEM recently organised a visit to a boiler
manufacturer, Boilermech Sdn. Bhd., for 13 3. The major materials for steam drum and
participants who included IEM members and water drum
engineers. 4. The marking and cuttings dished end
Mr. Wong Poon Han, the design manager blanks
of Boilermech, gave a briefing on the company
5. Rolling and fit shell plates
and its nature of business.
There are two types of steam boilers: 6. Weld & Radiography test (RT) for long
Water tube and fire tube, said Mr. Wong. seams and weld seams
Boilers are classified based on the type of 7. The joint process for shell and dished
fuel used, such as gaseous fuel (bio-methane heads
gas, natural gas, etc), liquid fuel (diesel, petrol,
8. Fit up of nozzles & attachment to shell/
methanol, etc) and solid fuel (biomass fuel,
head
rice husk, wood chips, etc).
Factory visit: A steam drum with completed marking and radiography test on
shell and dish heads. Ready for drilling on different nominal sizes of tubes.
Ci il, Geote hni al, Hydrauli , Marine and Landfill 12. The process flow of super heaters.
Engineering On the issues of quality and safety, Mr. Wong said its boilers
Soil Sta ilization, Earth orks, Erosion Control are designed to meet the requirements of enforcement
agency Jabatan Keselamatan & Kesihatan Pekerja (JKKP).
He said two types of carbon steel tubes are used,
i.e. the BS 3059 Part II Grade 360 and BS 3059 Part I
Grade 320. The selection of the nominal size of the
tube is based on design and application requirements.
These are mainly size 50.4mm and 76.2mm in diameter.
The length of the generating tubes is based on
design heating surfaces and market availability
(the longest on record is 14 metres).
Mr. Wong said: A boiler should be designed with high
efficiency, high steaming pressure and a capacity with
fuel that is available. Environmentally, however, a boiler
must be well designed and constructed to perform lower
Our Ser i es Our Produ ts dust concentration, with no dark smoke for the stack
Slope Repair Turf Rei for e e t Matri emission. Last but not least, the boiler must be able to
Rei for ed Soil Wall Erosio Co trol Bla ket operate safely.
Ke sto e Wall Coirlog & Stra Watters The participants were then taken on a
Soft Soil Sta ilizatio Profi Sa dfilled Mattress
tour of the factory, after which Ir. Hor Kok
Ri er Ba k Prote tio Geo ell / Geo e
Slope Erosio Co trol High Stre gth Geote tile Luen presented a token of appreciation to
Flood Mitigatio No o e Geote tile Mr. Wong.
Coastal Prote tio Pol ester Geogrid
Silt & Sedi e t Co trol Geo o posite / Geofa ri
La dfills Ga io & Ga io IEM DIARY OF EVENTS
O -site Dete tio Mattress Title: 2-Day Course on Project Management for
S ste HDPE Geo e ra e Operation & Maintenance Engineers (Postponed
Earth orks Geos theti Cla Li er
from 8 & 9 December 2015)
I frastru tures Che ili k
9 - 10 March 2016
LANDASAN IMPIAN SDN BHD CO. NO. -T Organised by : Graduates & Student - The Young Engineers
No - & - , Jala BPP / , Pusat Ba dar Putra Per ai, Section
Time : 9.00 a.m. 5.30 p.m.
Seri Ke a ga , Sela gor Darul Ehsa , Mala sia.
CPD/PDP : 14
Tel: - Fa : -
Desig Chi g : - Proje t Teo : - Kindly note that the scheduled events below are subject
E ail: la dasa i pia @g ail. o to change. Please visit the IEM website at www.myiem.org.
my for more information on the upcoming events.
42 JURUTERA February 2016 Editors Note: We welcome contributions from all members on travel stories.
GLOBE TREKKING
A-Bombs and A Peace-Loving People
y wife and I visited Hiroshima and
Editors Note: We welcome contributions from all members on travel stories. February 2016 JURUTERA 43
TEMUDUGA PROFESIONAL
seperi terse arai erikut diter itka se agai alo - alo a g 50132
LIJONG
REDZUAN BIN RASHID BE HONS (UiTM) (ELECTRICAL, 2007)
la ak u tuk e jadi Ahli I situsi, de ga s arat aha a ereka 22885 SYAHIRROHHIV BIN ABDUL BE HONS (UiTM) (ELECTRICAL, 2005)
SAMAT
lulus Temuduga Profesional tahun 2016. 50191 ZAIFULAMIR BIN MAHIDIN BE HONS (UTM) (ELECTRICAL, 2006)
PERMOHONAN BARU 72598 MOHD HISHAM BIN CHE AUN BE HONS (UTM) (MECHANICAL, 2003)
15409 MOHD SAIFUL ANUAR BIN ZAINAL BSc (BRADLEY) (MECHANICAL, 1991)
Nama Kelayakan 70391 MUKRIDZ BIN MD MOHTAR DIPL.ING (ESSLINGEN) (AUTOMOTIVE, 2005)
KEJURUTERAAN AWAM MSc (USM) (MECHANICAL, 2013)
ABDUL RAUF BIN ABD RAHIM BSc (GLASGOW) (CIVIL, 1985) 29930 TAY LEE SIEN BE HONS (USM) (MECHANICAL, 2010)
59076 TG MUHD AIMAN BIN TG BE HONS (IIUM) (MECHANICAL - AUTOMOTIVE,
AZRUL ASWAT BIN ABDUL SAMAD BE HONS (UTM) (CIVIL, 2001)
ABDULLAH 2011)
GHEE ENG HOW BE HONS (LIVERPOOL) (CIVIL, 1998) 41075 HARINDHARAN JEYABALAN BE HONS (UNISEL) (MECHATRONICS, 2009)
MBA (MALAYA) (2002) PhD (GRIFFITH) (2010) 29170 KUEH JOO KHENG, JUDY BE HONS (UTM) (CIVIL, 2006)
ROHANI BINTI AHMAD BSc (SOUTH DAKOTA) (CIVIL, 1987) 33682 MUHAMAD KHAIRI BIN JALIL BE HONS (UiTM) (CIVIL, 2008)
ME (UPM) (ENVIRONMENTAL, 2006)
SABIRIN BIN HASSAN BSc (NORTH CAROLINA) (CIVIL, 1987) PERMOHONAN BARU MENJADI AHLI KORPORAT
MBA (WINTHROP) (1991)
KEJURUTERAAN ELEKTRIKAL
SHAHIRWAN BIN AMAN SHAH BE HONS (UKM) (CIVIL & STRUCTURAL, 2003)
- MAZUAR BIN MOHD ANUAR BSc (SYRACUSE) (ELECTRICAL, 1986)
SHAIFUL SUKRI BIN ISMAIL ADV DIP (UiTM) (CIVIL, 1993)
WAN NORSHUHADA BINTI WAN BE HONS (UTM) (CIVIL, 2007)
KHAIRUDDIN
KEJURUTERAAN ELEKTRIKAL
KAHARUDIN BIN DIMYATI BE HONS (MALAYA) (ELECTRICAL, 1992)
MEMBERSHIP RENEWAL NOTICE AND
PhD (WALES) (1996) ANNUAL SUBSCRIPTION FOR 2016
MOHD FAHRI BIN ZAMRI BE HONS (UKM) (ELECTRICAL & ELECTRONIC, 2010)
MOHD SYAHMIN BIN MOHAMED BE HONS (UiTM) (ELECTRICAL, 2010)
OTHMAN
Greetings and Happy New Year 2016 from IEM.
MUHAMMAD RASYIDI BIN ZAINAL BE HONS (BATH) (ELECTRICAL & ELECTRONIC, 2001)
ABIDIN
In line with Bylaws Section 4.2 and 4.3, we are pleased to
NOR ASYIKIN BINTI DINYATI BE HONS (UNITEN) (ELECTRICAL & ELECTRONICS, 2004)
NUR DIYANA BINTI AHMAD NAWI BE HONS (UTM) (ELECTRICAL, 2008)
attach herewith your membership renewal notice for
2016. Kindly be informed that the annual subscription rates
KEJURUTERAAN KONTROL & INSTRUMENTASI excluding the 6% GST for 2016, which will become
MOHAMAD FASYAN BIN MOHAMAD BE HONS (UTP) (ELECTRICAL & ELECTRONICS, 2009)
SABRI due from 1st January 2016 are as follows:
KEJURUTERAAN MEKANIKAL
FELLOW : RM 265.00
MD AZMI BIN BABA BE HONS (UiTM) (MECHANICAL, 1996) SENIOR MEMBER : RM 210.00
MSc (UiTM) (INTEGRATED CONSTRUCTION PROJECT
MANAGEMENT, 2004) MEMBER : RM 155.00
MOHD ZURAIRI BIN ABD. GHANI BE HONS (IIUM) (MECHANICAL-AUTOMOTIVE, 2010) COMPANION / GRADUATE / AFFILIATE /
MUHAMMAD HAKIMI BIN HASHIM BE HONS (UTM) (MECHANICAL-AERONAUTICAL, 2002)
INCORPORATED MEMBER,
- who is on the 2016 have attained
PERPINDAHAN AHLI
the age of 30 : RM 155.00
No. Ahli Nama Kelayakan
KEJURUTERAAN AWAM
- have not attained the age of 30 : RM 100.00
22410 AZALI BIN ARDY@AZALI AH BE HONS (UKM) (CIVIL & STRUCTURAL, 2000)
SIONG
ASSOCIATE MEMBER, who is on the 2016:
45789 AZMAN BIN WAHID BE HONS (UTM) (CIVIL, 2010) - have attained the age of 30 : RM 155.00
28971 CHEN SHIN CHUAN BE HONS (UTM) (CIVIL, 1997) - have not attained the age of 30 : RM 100.00
47585 FAZILAH BINTI HATTA @ ANTAH BE HONS (UTM) (CIVIL, 2006)
27287 HASLAM RAMZAN BIN HASSAN BE HONS (UTHM) (CIVIL, 2006) STUDENT MEMBER, who is on the 2016
54337 KOK SIEN TI BE HONS (UNITEN) (CIVIL, 2006) - have attained the age of 30 : RM 155.00
PhD (UPM) (2011)
69503 LIM SOO FEEI, SOPHIA BE HONS (UTM) (CIVIL, 2005)
- have attained the age of 24 : RM 100.00
75261 SHAHIRON BIN SHAHIDAN BE HONS (UNISEL) (CIVIL,2007) - have attained the age of 24 and are bona ide students of
ME (UPM) (STRUCTURAL & CONSTRUCTIONS,
2010) PhD (USM) (2014)
institutions of higher learning : RM 20.00
24873 TAUFIKUR RAHMAN BIN ADNAN BE HONS (UiTM) (CIVIL, 2002) - have not attained the age of 24 : RM 20.00
7045 WAN MOHD AMZAR BIN WAN BE HONS (KLiUC) (CIVIL, 2011)
MANAN Note: Kindly be informed that as per our announcement on 1 October 2015, GST is
47584 YONG SUI SU BE HONS (QUT) (CIVIL, 2009) chargeable on IEM Subscriptions at the rate of 6%.
79151 MOHAMAD SHAFIQ B.E.HONS.(UITM) 79112 MUHAMMAD DANIAL B.E.HONS.(UITM) 79125 ZURAINE AZANEN B.E.HONS.(UITM)
BIN IBRAHIM (ELECTRONIC, 2015) BIN MOHD RADZI (ELECTRONIC- BINTI ZULKIPLI (ELECTRONIC-
INSTRUMENTATION, COMPUTER, 2015)
79131 MOHAMAD SYAHMI B.E.HONS.(UITM)
2015)
BIN ZULLKIFFLE (ELECTRONIC, 2015)
79163 MUHAMMAD HAFIZ B.E.HONS.(UITM)
79103 MOHAMAD SYAMIL B.E.HONS.(UITM) KEJURUTERAAN INDUSTRI
BIN HARUN (ELECTRONIC-
BIN KAMARUDIN (ELECTRONIC, 2015)
INSTRUMENTATION, 79507 SARAVIN KUMAR A/L B.E.HONS.(UTAR)
78867 MOHD ARIFF BIN MAT B.E.HONS.(UTM) 2015) T N BINU KUMAR (INDUSTRIAL, 2015)
YAZID (ELECTRICAL-
79114 MUHAMMAD SYUKRI B.E.HONS.(UITM)
ELECTRONICS, 2009)
MAULA ABDUL (ELECTRONIC- KEJURUTERAAN KIMIA
79128 MOHD EEZLEE BIN B.E.HONS.(UITM) SAMAD INSTRUMENTATION,
MOHD SAPUDDIN (ELECTRONIC- 2015) 79494 ABDUL HALIM BIN B.E.HONS.(UITM)
INSTRUMENTATION, NORDIN (CHEMICAL & PROCESS,
79156 MUHAMMAD ZAHID B.E.HONS.(UITM) 2015)
2015)
BIN ZAMRI (ELECTRONIC-
79137 MOHD FAIZULHAYAD B.E.HONS.(UITM) INSTRUMENTATION, 79493 AFIF BAZLAA BINTI B.E.HONS.(UITM)
BIN MASHURI (ELECTRONIC- 2015) JUWAHIR (CHEMICAL, 2015)
INSTRUMENTATION, 78467 AFIFAH BINTI HAPIDZ B.E.HONS.(UMP)
79036 MUSTAFA KAMAL BIN B.E.HONS.(UITM)
2015) (CHEMICAL, 2010)
SURIF (ELECTRONIC-
79135 MOHD HARIZ BIN B.E.HONS.(UITM) INSTRUMENTATION, 79492 AHMAD FAKHRI B.E.HONS.(UITM)
BADRUDDIN (ELECTRONIC- 2015) SYAHMI BIN (CHEMICAL &
INSTRUMENTATION, MASRUDDIN BIOPROCESS, 2015)
79145 MUSTAQIM BIN B.E.HONS.(UITM)
2015)
KAMARU' ZZAMAN (ELECTRONIC- 79491 AHMAD FIRDAUS BIN B.E.HONS.(UITM)
78887 MOHD HILMAN B.E.HONS.(UITM) COMMUNICATION, 2015) MUHAMMAD ASHA'RI (CHEMICAL & PROCESS,
LUKMAN (ELECTRICAL, 2008) 2015)
79159 NABILAH HUMAIDI B.E.HONS.(UITM)
79158 MOHD MOKHZANI BIN B.E.HONS.(UITM) (ELECTRONIC- 79490 ANITH ATHIRA BINTI B.E.HONS.(UITM)
MOKHSIN @ MISRON (ELECTRONIC- COMMUNICATION, 2015) CHE ABD RAHIM (CHEMICAL & PROCESS,
INSTRUMENTATION, 2015)
79157 NOOR AZIZAH BINTI B.E.HONS.(UITM)
2015)
ABU KHAMID (ELECTRONIC- 79489 ASMAA' BINTI B.E.HONS.(UITM)
79140 MOHD NASRUL B.E.HONS.(UITM) COMMUNICATION, 2015) ABDULLAH (CHEMICAL, 2015)
AFFENDI B ABU (ELECTRONIC-
79328 NOORFOZILA BINTI B.SC.(GEORGE 79488 AYU AZRAINE BINTI B.E.HONS.(UITM)
HURAIRAH INSTRUMENTATION,
BAHARI WASHINGTON) MOHAMMED SALLEH (CHEMICAL & PROCESS,
2015)
(ELECTRICAL, 2015)
79118 MOHD NAZRIN B.E.HONS.(UITM) 1988) M.SC.(UKM)
SYAHMI BIN ZAINI (ELECTRONIC- 78899 AZAD SHAHREN BIN B.E.HONS.(UTM)
(MICROELECTRONIC,
INSTRUMENTATION, MAT TAP (CHEMICAL, 2006)
2007)
2015) 79411 AZWADI BIN ALI B.E.HONS.(UITM)
79122 NORHASNIZA BINTI B.E.HONS.(UITM)
79127 MOHD NOOR ASHRAF B.E.HONS.(UITM) (CHEMICAL &
WAHID (ELECTRONIC-
BIN MAAMOR (ELECTRONIC- BIOPROCESS, 2015)
COMMUNICATION, 2015)
INSTRUMENTATION, 78469 CHANG HAI PENG B.E.HONS.(MIINESOTA)
79115 NORMASLINDA BINTI B.E.HONS.(UITM)
2015) (CHEMICAL, 2011)
MOHD SAHAT (ELECTRONIC-
79025 MOHD NORBI BIN B.E.HONS.(UITM) COMMUNICATION, 2015) 79321 CHIN YONG BAO B.E.HONS.(UTP)
BAHARIN (ELECTRONIC- (CHEMICAL, 2013)
79120 NUR FARAHAIN BTE B.E.HONS.(UITM)
INSTRUMENTATION, 79545 CH'NG BOON SIN B.E.HONS.(UTAR)
MOHAMMED (ELECTRONIC-
2015) (CHEMICAL, 2015)
COMMUNICATION, 2015)
79153 MOHD RAFIUDDIN B.E.HONS.(UITM) 79031 DR. LEO CHOE PENG B.E.(UMP)(CHEMICAL,
79116 NUR IZZATI BINTI B.E.HONS.(UITM)
BIN MOHD ROBI (ELECTRONIC- 2013)
NASIR (ELECTRONIC-
INSTRUMENTATION,
COMMUNICATION, 2015) 78409 DR. SYED SHATIR B.E.HONS.(NEWCASTLE
2015)
79123 NUR SYAAHIDAH B.E.HONS.(UITM) ASGHRAR BIN SYED UPON TYNE)(CHEMICAL,
79316 MOHD REDZUWAN B.E.HONS.(UNITEN) HASSAN 2003) P.HD.(CURTIN)
BINTI MUSTAFA (ELECTRONIC-
BIN ABU KASIM (ELECTRICAL & (2011)
COMMUNICATION, 2015)
ELECTRONIC, 2006)
79139 NURUL FARAHIN B.E.HONS.(UITM) 79487 FARHAN FASEEHA B.E.HONS.(UITM)
79129 MOHD SAFUAN BIN B.E.HONS.(UITM) BINTI ISMAIL (CHEMICAL & PROCESS,
BINTI SAID (ELECTRONIC-
ZULKIFLI (ELECTRONIC- 2015)
COMMUNICATION, 2015)
INSTRUMENTATION,
2015) 79107 NURUL SYAHIDA BT B.E.HONS.(UITM) 79486 FARHANA BINTI B.E.HONS.(UITM)
MOHD TAJUDIN (ELECTRONIC- HARUN (CHEMICAL & PROCESS,
78486 MOHD SHARIF BIN B.E.HONS.(UTM) 2015)
COMMUNICATION, 2015)
ZAKARIA (ELECTRICAL-
MICROELECTRONICS, 78074 RASIDI BIN YAMIN B.E.HONS.(BRADFORD) 79485 HAIRIE BIN HELMAN B.E.HONS.(UITM)
2001) M.E.(UTHM) (ELECTRONIC, 1995) (CHEMICAL, 2015)
(ELECTRICAL, 2013) 79323 RUZITA BINTI ABU B.SC.(WIDENER) 79484 HANISAH BINTI B.E.HONS.(UITM)
79161 MOHD SHUKRI BIN B.E.HONS.(UITM) BAKAR (ELECTRICAL, 1992) SARKAWI @ KAWI (CHEMICAL & PROCESS,
HUSIN (ELECTRONIC- M.SC.(UPM)(COMPUTER 2015)
INSTRUMENTATION, & COMMUNICATION 79483 HAZWANI BINTI B.E.HONS.(UITM)
2015) SYSTEMS, 2001) BASRI (CHEMICAL & PROCESS,
79108 MOHD ZAID BIN B.E.HONS.(UITM) 79119 SALHA BINTI DALHAM B.E.HONS.(UITM) 2015)
TAJUDIN (ELECTRONIC- (ELECTRONIC- 79006 HENG SUI WOOI B.E.HONS.(MALAYA)
INSTRUMENTATION, COMMUNICATION, 2015) (CHEMICAL, 2004)
2015) 79132 SHAHRIZAN BIN B.E.HONS.(UITM) 79482 HIDAYATUL HUSNA B.E.HONS.(UITM)
79141 MOHD. AZLAN BIN B.E.HONS.(UITM) RASHID (ELECTRONIC- BINTI HUSSIN (CHEMICAL, 2015)
YUSUFF (ELECTRONIC- COMMUNICATION, 2015)
78455 HO MENG FAN B.E.HONS.(UTAR)
INSTRUMENTATION, 79146 SHARAFUDDIN BIN B.E.HONS.(UITM) (CHEMICAL, 2013)
2015) MOHD KHAIRUDDIN (ELECTRONIC-
79481 IHSAN SABRI BIN B.E.HONS.(UITM)
79110 MUHAMAD HAFIZ B.E.HONS.(UITM) COMMUNICATION, 2015)
ROSLI (CHEMICAL & PROCESS,
FARHAN BIN RAFII (ELECTRONIC- 79147 SHAZLIEZAWATY B.E.HONS.(UITM) 2015)
INSTRUMENTATION, BINTI SAHA HU (ELECTRONIC-
2015) 79408 IRFAN SYUKRI BIN B.E.HONS.(UITM)
HAMID COMMUNICATION, 2015)
ISMAIL (CHEMICAL & PROCESS,
79134 MUHAMAD ZULHELMI B.E.HONS.(UITM) 79106 SHIMAN BIN SAIMAN B.E.HONS.(UITM) 2015)
BIN ABDULLAH (ELECTRONIC- (ELECTRONIC-
INSTRUMENTATION, 79480 KAIRUL SHA BIN B.E.HONS.(UITM)
COMMUNICATION, 2015)
2015) DULDANG (CHEMICAL, 2015)
79113 SITI SARAH BINTI B.E.HONS.(UITM)
79029 MUHAMMAD B.E.HONS.(UITM) 79318 KONG YEAN HUEY B.E.HONS.(CURTIN)
KHALID (ELECTRONIC-
AFIQ ZIMAM (ELECTRONIC- (CHEMICAL, 2006)
COMMUNICATION, 2015)
BIN MOHAMED INSTRUMENTATION, 78860 LAM KA-MUN B.E.HONS.
MUNAWAR 2015) 79124 SYAKINAH BINTI B.E.HONS.(UITM)
(CANTERBURY)
ZAKARIA (ELECTRONIC-
79150 MUHAMMAD AIZAT B.E.HONS.(UITM) (CHEMICAL & PROCESS,
COMMUNICATION, 2015)
BIN MD RASID (ELECTRONIC- 2009)
INSTRUMENTATION, 78869 TING TZE MING, B.E.HONS.(MMU)
79532 LIM FUI CHIN B.E.HONS.(UTAR)
2015) SIMON (ELECTRONICS-
(CHEMICAL, 2015)
TELECOMMUNICATIONS,
79030 MUHAMMAD AIZAT B.E.HONS.(UITM) 2010) 79409 LUQMAN HAKIM BIN B.E.HONS.(UITM)
BIN ZAKARIA (ELECTRONIC- ABDUL RAZAK (CHEMICAL, 2015)
INSTRUMENTATION, 79162 WAN ABDUL B.E.HONS.(UITM)
HAZIQULLAH BIN (ELECTRONIC- 79479 LYDIA CHRISTINE AK B.E.HONS.(UITM)
2015)
WAN JAMALUDDIN COMMUNICATION, 2015) MARTIN (CHEMICAL, 2015)
79126 MUHAMMAD B.E.HONS.(UITM)
79130 WAN MOHAMMAD B.E.HONS.(UITM) 79526 MAH BEE LING B.E.HONS.(UTAR)
AIZUDDIN BIN AZMI (ELECTRONIC-
QODRY BIN WAN (ELECTRONIC- (CHEMICAL, 2015)
INSTRUMENTATION,
2015) KAMIZI COMPUTER, 2015) 79478 MAHIRAH BINTI ABD B.E.HONS.(UITM)
79155 WAN MOHD NAIM BIN B.E.HONS.(UITM) MUBIN (CHEMICAL & PROCESS,
79133 MUHAMMAD B.E.HONS.(UITM)
WAN GHAZALI (ELECTRONIC- 2015)
AMINUDDIN BIN (ELECTRONIC-
ABIDIN INSTRUMENTATION, COMPUTER, 2015) 79421 MARCELLE MARTIN B.E.HONS.(UITM)
2015) 79138 WAN NUR ATHIRAH B.E.HONS.(UITM) (CHEMICAL & PROCESS,
BINTI WAN AZAHAR (ELECTRONIC- 2015)
79117 MUHAMMAD AZHAR B.E.HONS.(UITM)
BIN BORHAN (ELECTRONIC- COMPUTER, 2015) 79416 MASLAN BIN HASSAN B.E.HONS.(UITM)
INSTRUMENTATION, 79152 WAN ZUHELMI BIN B.E.HONS.(UITM) (CHEMICAL, 2015)
2015) WAN MUDA (ELECTRONIC-
COMPUTER, 2015)
79418 MD.RAHMADI BIN B.E.HONS.(UITM) 79454 NORASYIKIN BINTI B.E.HONS.(UITM) 79424 SYAHIRAH BT HARUN B.E.HONS.(UITM)
RASALI (CHEMICAL & PROCESS, MOKTAR (CHEMICAL, 2015) (CHEMICAL, 2015)
2015) 79453 NORMASZIANA BINTI B.E.HONS.(UITM) 79415 SYANTA JOSEPH B.E.HONS.(UITM)
79477 MOHAMAD HAKIM B.E.HONS.(UITM) SIDEK (CHEMICAL & PROCESS, (CHEMICAL & PROCESS,
BIN KAMARUDDIN (CHEMICAL, 2015) 2015) 2015)
79476 MOHAMMAD AMIRUL B.E.HONS.(UITM) 79452 NORSOLEHAH BINTI B.E.HONS.(UITM) 79013 TEE PEI FANG B.E.HONS.(UPM)
AIMAN BIN AHAMAD (CHEMICAL & PROCESS, HANAFIAH (CHEMICAL, 2015) (CHEMICAL, 2007)
2015) 79346 NU'MAN BIN ABDUL B.E.HONS.(UTM) 79019 TEY SIU LEE B.E.HONS.(UTP)
79475 MOHAMMAD IZWAN B.E.HONS.(UITM) HADI (CHEMICAL, 2009) (CHEMICAL, 2013)
BIN ABDUL WAHID (CHEMICAL & PROCESS, 79428 NUR FATHIN AMIRAH B.E.HONS.(UITM) 79023 THIVAGAR A/L B.E.HONS.(UTP)
2015) BINTI SHAFIE (CHEMICAL, 2015) SUGUMARAN (CHEMICAL, 2014)
79474 MOHAMMAD B.E.HONS.(UITM) 79427 NUR RUZAINI BINTI B.E.HONS.(UITM) 79430 WAN AFIFF BIN WAN B.E.HONS.(UITM)
NAZREEN BIN (CHEMICAL & PROCESS, ROSLI (CHEMICAL & AZNI (CHEMICAL & PROCESS,
ZAINURIN 2015) BIOPROCESS, 2015) 2015)
79473 MOHD ALFIE SABALI B.E.HONS.(UITM) 79451 NUR SYAFIQA BINTI B.E.HONS.(UITM) 79429 WAN FATHI HATIM B.E.HONS.(UITM)
(CHEMICAL & PROCESS, AMAN (CHEMICAL, 2015) DIYANA BT WAN (CHEMICAL, 2015)
2015) NORMAN
79420 NURLIYANA BINTI B.E.HONS.(UITM)
79472 MOHD AMIRUL HAKIM B.E.HONS.(UITM) SHAHADAN (CHEMICAL & PROCESS, 79510 WONG KIN KEN B.E.HONS.(UTAR)
BIN MOHD ZIN (CHEMICAL & PROCESS, 2015) (CHEMICAL, 2015)
2015)
79450 NURRUL SHAFIQAH B.E.HONS.(UITM) 78488 WONG SENG SIONG, B.SC.(IOWA STATE)
79471 MOHD FAIZZUL BIN B.E.HONS.(UITM) BINTI MAHAMAD TAIB (CHEMICAL, 2015) RONNY (CHEMICAL, 2004)
MOHD ZAIDI (CHEMICAL & PROCESS,
2015) 79425 NURUL AISHAH BINTI B.E.HONS.(UITM) 79018 WONG YEE YIEN M.E.HONS.
MAZLAN (CHEMICAL & PROCESS, (NOTTINGHAM)
79470 MOHD FAROOQ BIN B.E.HONS.(UITM) 2015) (CHEMICAL, 2010)
MOHAMAD KHALIL (CHEMICAL & PROCESS,
2015) 79449 NURUL AZIANI BINTI B.E.HONS.(UITM)
SYAARI (CHEMICAL, 2015)
78474 MOHD HAFIZ BIN B.E.HONS.(UTM) KEJURUTERAAN KOMUNIKASI
ZAKARIA (CHEMICAL, 2009) 79448 NURUL FAZLINA BINTI B.E.HONS.(UITM)
79324 DR. NURUL B.E.HONS.(IIUM)
NOOR FAZIL (CHEMICAL & PROCESS,
78882 MOHD KHAIRUL BIN B.E.HONS.(UMP) SHAHRIZAN BINTI (COMMUNICATION,
2015)
YA'KUB (CHEMICAL, 2008) SHAHABUDDIN 2006) M.SC.(MALAYA)
79447 NURUL HASIDAH B.E.HONS.(UITM) (PHOTONIC, 2009)
79410 MOHD NUZUL AMIN B.E.HONS.(UITM) BINTI MOHAMAD (CHEMICAL, 2015) P.HD.(MALAYA)
BIN MOHD SALLEH (CHEMICAL, 2015)
79446 NURUL NADIA BINTI B.E.HONS.(UITM) (PHOTONIC, 2013)
79426 MOHD RIDZUAN BIN B.E.HONS.(UITM) MOHAMAD (CHEMICAL & PROCESS,
MOHATAR (CHEMICAL, 2015) 2015)
79419 MOHD ZULFADHLI B.E.HONS.(UITM) KEJURUTERAAN MEKANIKAL
79445 NURUL WAHIDA BINTI B.E.HONS.(UITM)
BIN FAIZOL AZMI (CHEMICAL, 2015) ABD HALIM (CHEMICAL, 2015) 78071 ADNAN BIN BAKRI B.E.HONS.(ITM)
79469 MUFIDAH BINTI B.E.HONS.(UITM) (MECHANICAL, 1997)
79520 PANG TUNG HEE B.E.HONS.(UTAR)
MAHFUZ (CHEMICAL & PROCESS, (CHEMICAL, 2015) 78879 AMIRUL HAKIM BIN B.E.HONS.(UPNM)
2015) SUFIAN (MECHANICAL, 2012)
79444 PAZILAH BINTI MOHD B.E.HONS.(UITM)
78404 MUHAMAD FAUZAN B.E.HONS.(UTM) YUSOF (CHEMICAL & 79340 ANG PENG CHONG B.E.HONS.(UTAR)
BIN AHMAD FADZIL (CHEMICAL, 2014) BIOPROCESS, 2015) (MECHANICAL, 2010)
79468 MUHAMAD SHAHIR B.E.HONS.(UITM) 79443 PEREGRINE DAVID B.E.HONS.(UITM) 79549 AU WING FAI B.E.HONS.(UTAR)
BIN MOHD SAAT (CHEMICAL, 2015) (CHEMICAL, 2015) (MECHANICAL, 2015)
79467 MUHAMMAD AFIQ BIN B.E.HONS.(UITM) 79010 PHOON KOK HOONG B.E.HONS.(UKM) 79322 AZUREEN BINTI M.E.HONS.(SUSSEX)
IBRAHIM (CHEMICAL & PROCESS, (CHEMICAL, 2004) P.HD. MOHD KAMAL AZMEY (MECHANICAL, 2014)
2015) (USM)(MEMBRANES/ 79306 CHAI KOON SENG B.E.HONS.(UTP)
79422 MUHAMMAD FADHLI B.E.HONS.(UITM) MEMBRANE TECH (MECHANICAL, 2014)
BIN SAMSUDIN (CHEMICAL & PROCESS, FOR ENVIRONMENTAL 79004 CHAN YING WAI B.E.(SUNDERLAND)
2015) POLLUTION CONTROL, (MECHANICAL, 1988)
79417 MUHAMMAD FAIZ BIN B.E.HONS.(UITM) 2008)
78463 CHEAH EE GUAN, B.E.HONS.(UNITEN)
ISMAIL (CHEMICAL & 79442 RAJA MOHD ADLI BIN B.E.HONS.(UITM) AARON (MECHANICAL, 2014)
BIOPROCESS, 2015) RAJA ARIS (CHEMICAL, 2015)
79352 CHEAH YUANFENG B.E.HONS.(MALAYA)
78900 MUHAMMAD FAIZ BIN B.E.HONS.(MELBOURNE) 79441 ROHAZIERAH BINTI B.E.HONS.(UITM) (MECHANICAL, 2014)
OMAR (CHEMICAL, 2013) CHE OMAR (CHEMICAL & PROCESS,
2015) 79016 CHENG SEOK THENG B.E.HONS.(UNIMAS)
79466 MUHAMMAD FAKHRI B.E.HONS.(UITM) (MECHANICAL &
BIN HASAN @ AHMAD (CHEMICAL & PROCESS, 79440 ROYDIA LENSY ANAK B.E.HONS.(UITM) MAUFACTURING, 2014)
2015) SIMAN (CHEMICAL, 2015)
79546 CHIN GUANG MIN B.E.HONS.(UTAR)
79465 MUHAMMAD B.E.HONS.(UITM) 79439 SALIP ELNALYN B.E.HONS.(UITM) (MECHANICAL, 2015)
FAREEZUDDIN BIN (CHEMICAL & PROCESS, SALIP MAWALLIL (CHEMICAL & PROCESS,
MOHAMAD KHALIL 2015) 2015) 78421 CHIONG JONG HUA B.E.HONS.(PLYMOUTH)
(MECHANICAL, 2003)
79464 MUHAMMAD JASVIR B.E.HONS.(UITM) 79519 SASHITHAARAN A/L B.E.HONS.(UTAR)
BIN SULAIMAN (CHEMICAL & PROCESS, GOVINDASAMY (CHEMICAL, 2015) 78418 CHOO LIANG FEE B.E.HONS.(UKM)
2015) (MECHANICAL, 2008)
79438 SITI AUNI NABILAH B.E.HONS.(UITM)
79463 MUHAMMAD KAMAL B.E.HONS.(UITM) BINTI KAMARUDDIN (CHEMICAL & PROCESS, 79506 CHOONG BOON HAO B.E.HONS.(UTAR)
BIN ISMAIL (CHEMICAL & 2015) (MECHANICAL, 2015)
BIOPROCESS, 2015) 79437 SITI FARAH NADIAH B.E.HONS.(UITM) 79297 DINISHKARAN PILLAI B.E.HONS.(UNITEN)
79462 MUHAMMAD NADZMI B.E.HONS.(UITM) BINTI RUSLI (CHEMICAL & A/L VELAYUTHAM (MECHANICAL, 2010)
BIN RAMLAN (CHEMICAL & PROCESS, BIOPROCESS, 2015) PILLAI
2015) 79412 SITI HAJARNAIMAH B.E.HONS.(UITM) 78460 DR. MUHAD ROZI BIN B.E.HONS.(USM)
79461 MUHAMMAD B.E.HONS.(UITM) KAMARUDDIN (CHEMICAL, 2015) MAT NAWI (MECHANIC, 2005)
NURFIRDAUS BIN (CHEMICAL, 2015) M.SC.(MECHANIC, 2008)
78410 SITI KHATIJAH BINTI B.E.HONS.(UTM) P.HD.(TRINITY COLL.
RASIDI JAMALUDIN (CHEMICAL, 2005) DUBMIN)(2015)
79460 MUHAMMAD RAIHAN B.E.HONS.(UITM) M.SC.(UITM)(CHEMICAL,
BIN ABD TALIB (CHEMICAL & PROCESS, 2012) 78458 DR. NURIN WAHIDAH B.E.HONS.(MALAYA)
2015) MOHD ZULKIFLI (MECHANICAL, 2006)
78076 SITI MARIAH BINTI M.E.HONS. M.E.SC.(MONASH)(2009)
79459 MUHAMMAD WAFIY B.E.HONS.(UITM) ABDUL MURAD (MANCHESTER) P.HD.(MALAYA)(2014)
BIN AHMAD (CHEMICAL & (CHEMICAL, 2013)
BIOPROCESS, 2015) 78865 DR.NG KEAN ENG B.E.(MURORAN INST.)
79423 SITI NOR SAMRAH B.E.HONS.(UITM) (MECHANICAL SYSTEMS,
79458 MUHD SYAFIQ IZWAN B.E.HONS.(UITM) BINTI A.RAHIM (CHEMICAL & PROCESS, 1998) M.E.(MURORAN
BIN ZAINAL MURAD (CHEMICAL, 2015) 2015) INST.)(MECHANICAL
79457 MUZZAFFAR ZAIDI B.E.HONS.(UITM) 79436 SITI NORFASHA BINTI B.E.HONS.(UITM) SYSTEMS, 2000) P.HD.
BIN MUSTAPHA (CHEMICAL & PROCESS, ABU BAKAR (CHEMICAL, 2015) (MURORAN INST.)
2015) 79435 SITI NUR TAQINAH B.E.HONS.(UITM) (PRODUCTION &
79414 NABILA SHAFIQAH B.E.HONS.(UITM) BINTI MURSIDI (CHEMICAL & PROCESS, INFORMATION SYSTEMS,
DABIMEL (CHEMICAL & PROCESS, 2015) 2003)
2015) 79434 SITI NURAINSYAH B.E.HONS.(UITM) 79542 FANG WAI HONG B.E.HONS.(UTAR)
79525 NEOH KUANG HONG B.E.HONS.(UTAR) BINTI SHARUDDIN (CHEMICAL & PROCESS, (MECHANICAL, 2015)
(CHEMICAL, 2015) 2015) 78406 IJHAR HIDAYAT BIN B.E.HONS.UITM()
78072 NG KAY WENG, B.E.HONS.(UTAR) 79433 SITI SARAHNAIMAH B.E.HONS.(UITM) RUSLI (MECHANICAL,
DANIEL (CHEMICAL, 2014) BT KAMARUDDIN (CHEMICAL, 2015) 2007) M.SC.
(UPM)(MECHANICAL,
79456 NOOR HIDAYAH BINTI B.E.HONS.(UITM) 79432 SITI ZAKIAH BT B.E.HONS.(UITM) 2012)
HASBAH (CHEMICAL & PROCESS, RAZALI (CHEMICAL, 2015)
2015) 78875 KANNAN A/L VIJAYAM B.E.HONS.(UTP)
79516 SOON ZHENG B.E.HONS.(UTAR) (MECHANICAL, 2014)
79455 NOR FARAHIDA BINTI B.E.HONS.(UITM) FOONG (CHEMICAL, 2015)
ABU BAKAR (CHEMICAL & 79314 KUANG JIA FEI B.E.HONS.(UTHM)
79431 SUHAILA BINTI B.E.HONS.(UITM) (MECHANICAL, 2014)
BIOPROCESS, 2015) SHAWAL (CHEMICAL, 2015)
79413 NORAINI BINTI ALUWI B.E.HONS.(UITM) 79540 KUEH JIN FONG B.E.HONS.(UTAR)
79305 SURENTHRAN A/L K B.E.HONS.(UMP) (MECHANICAL, 2015)
(CHEMICAL & PROCESS, SUNDAR (CHEMICAL, 2014)
2015) 79539 LEE CHUN WAI B.E.HONS.(UTAR)
(MECHANICAL, 2015)
78466 LEE LAI HOONG B.E.HONS.(UNITEN) 79332 RAMKUMAR A/L B.E.HONS.(UNITEN) 78405 SIM CHIA WEE B.E.HONS.(CURTIN)
(MECHANICAL, 2014) KARUPPIAH (MECHANICAL, 2013) (MECHANICAL, 2014)
79535 LEE ZHENG HAU B.E.HONS.(UTAR) 78037 RICHARD BIN TIAM @ B.E.HONS.(UPM) 79307 SIM JIA SIANG B.E.HONS.(UTM)
(MECHANICAL, 2015) ALOYSIUS (MECHANICAL, 2002) (MECHANICAL-
M.E.(UTEM) MATERIALS, 2010)
79259 LIM CHAN CHENG B.E.HONS.(MMU)
(MECHANICAL, 2012) M.E.(UTM)(MECHANICAL-
(MECHANICAL, 2009)
79040 SHAMINI A/P B.E.HONS.(USM) MATERIALS, 2012)
M.B.A.(UPM)(FINANCE,
2013) PATPANAVAN @ (MECHANICAL, 2012)
PATHMANATHAN Note: Remaining list would be published in the March
78871 LIM HOOI PENG B.E.HONS.(UTM)
(MECHANICAL- 79034 SIEW JUN SOON B.E.HONS.(UTHM)
2016 issue. For the list of approved ADMISSION TO
MATERIALS, 2008) (MECHANICAL, 2011) THE GRADE OF STUDENT, please refer to IEM web
M.E.(UTM)(MECHANICAL, portal at http://www.myiem.org.my.
2014)
78407 LIM SOON CHONG, B.E.HONS.(KUITTHO)
JOHNSON (MECHANICAL, 2002)
79531 LOCK WENG LEONG B.E.HONS.(UTAR)
Pengumuman
(MECHANICAL, 2015) yang ke-88
79342 LOGESWARAN A/L B.E.HONS.(UNISEL)
ARUMUGAM (MECHANICAL, 2014)
79300 LOK YEE FAI B.E.HONS.(UMS)
(MECHANICAL, 2006) SENARAI PENDERMA KEPADA WISMA DANA BANGUNAN IEM
79527 LU AIK WAY B.E.HONS.(UTAR)
(MECHANICAL, 2015) Institusi mengucapkan terima kasih kepada semua yang telah
79253 MOHAMAD FAIZ BIN B.E.HONS.(UITM)
MOHD SHAFIE (MECHANICAL, 2015) memberikan sumbangan kepada tabung Bangunan Wisma IEM.
78468 MOHAMAD SHIHAB B.E.HONS.(UITM) Ahli-ahli IEM dan pembaca yang ingin memberikan sumbangan
BIN SENIK @ ABDUL (MECHANICAL, 2007)
MOKHTI boleh berbuat demikian dengan memuat turun borang di laman
78866 MOHAMAD B.E.HONS.(UNIMAS)
ZULFADELI BIN RIPAN (MECHANICAL &
web IEM http://www.iem.org.my atau menghubungi secretariat
MANUFACTURING, 2013) di +603-7968 4001/5518 untuk maklumat lanjut. Senarai penyumbang
78411 MOHAMED SUKRI BIN B.E.HONS.(UTM)
MAT ALI (MECHANICAL, 2004) untuk bulan Disember 2015 adalah seperti jadual di bawah:
M.E.(UTM)(MECHANICAL,
2007)
79310 MOHD AZAM BIN B.E.HONS.(UNISEL) NO. NO. AHLI NAMA
MOHD AZNI (MECHANICAL, 2013)
1 69516 ABANG NIZAMUDDIN BIN ABANG MOHD KHALID
78457 MOHD FAIRUZ BIN B.SC.(ARIZONA STATE)
MUHAMMAD PILOS (MECHANICAL, 1997)
2 12076 ABD YUZID BIN MAT YASSIN
78898 MOHD FAIZUL BIN DIPL-ING.
ABD RAHMAN (GELSENKIRCHEN)
(MECHANICAL, 2010) 3 17134 ABD. FATAH BIN MOHAMED
79349 MOHD FIRDAUS BIN B.E.HONS.(UPM)
ADAM (MECHANICAL, 2007) 4 03452 ABD. RAHIM BIN SHAMSUDIN
79339 MOHD HAFIZUL HILMI B.E.HONS.(UTM)
BIN MOHD NOOR (MECHANICAL, 2011) 5 28831 ADLY FARRIZ BIN FAIZAL
79254 MOHD ZAIMI BIN ABD B.E.HONS.(MALAYA)
RAHIM (MECHANICAL, 1994) 6 46809 ANDY LAWRENCE
79033 MOKANARAJU A/L B.E.HONS.(UNITEN)
K.SELVARAJ (MECHANICAL, 2014) 7 19429 CHONG VUN LEONG
78487 MUHAMMAD B.E.HONS.(ADELAIDE)
DZARFAN BIN (MECHANICAL, 2012) 8 33778 CHUA KOK LIANG @ HENRY CHUA
MUHAIYUDDIN
79252 MUHAMMAD JAAFAR B.E.HONS.(UITM) 9 08432 LAW KEN CHOONG
BIN JAMAREI (MECHANICAL, 2015)
78481 MUHYIZZ BIN B.E.HONS.(LEICESTER) 10 19969 MOHANA MURALI A/L KUPPUSAMY
MOHAMMED (MECHANICAL, 2012)
M.SC.(LEICESTER)(ADV. 11 43737 MOHD ROSLAN BIN DAUT
MECHANICAL ENRG.,
2014)
12 29281 MUHAMMAD FAKHRUDDIN BIN ALI
79353 NG CHEE CHUNG B.E.HONS.(UTM)
(MECHANICAL, 2014)
13 42604 NAHROWI BIN SULAIMAN
78485 NIK MOHD SYAFIQ B.E.HONS.(UTM)
HAZWAN B NIK AB (MECHANICAL-
GHANI MATERIALS, 2010) 14 41273 NG CHOON AUN