Académique Documents
Professionnel Documents
Culture Documents
1) MOTOR QUESTIONS
1) RECTIFIER QUESTIONS
45. Cascade amplifier is used because
a. High Voltage gain
b. High output impedance
c. High input impedance
46. Cascade amplifier used to reduce load effect, the input impedance will be
a. High (advantage: High band width and stability)& disadvantage(requires a relatively high supply voltage)
b. Low
c. Medium
47. Cascade amplifier used to reduce load effect, the output impedance will be
a. High
b. Low
c. Medium
48. The output for the cascade amplifier is
a. Output of the first stage
b. Output of the last stage
49. What is the low-pass filter?
a. It will let pass low frequencies? (or it blocks high frequency)
b. It will let pass high frequencies?
c. It will let pass a band of frequencies?
d. It will eliminate a band of frequencies?
50. What is the role of the zener diode?
a. Rectification
b. Amplification
c. voltage regulation
51. Filter in active region.
a. Filters the signal
b. Filter, amplifies and modulates
c. Filter and amplifies
52. Type of amplifier at receiver in order to amplify the signal?
a. Power amplifier
b. Differential amplifier
53. When using Ziner diode for voltage regulation, the output wave shape will be affected by
a. Dynamic resistance of the diode
b. Input current passing through the diode
54. Ohms Law (the right one is U=RI, they put choices not related to this law)
55. For an inverter op-amp, what will be the equivalent output resistance?
a. Zero
b. Infinity
c. Relative forward resistance
d. Same as the input resistance.
56. The heat loss inside a straight conductor is 60J upon applying current I for 5s. if the resistance of
the conductor is decease to half, and the same current is applied for 5s, what will be the heat
dissipation:
a. 60J
b. 30J
c. 15J
d. 120J
57. Fan out logic gate is
a. Number of gate
b. Number of gate connect to output
58. Type of amplifier at transmitter?
a. Power amplifier
b. Differential Amplifier
59. Loading effect can be reduced in a system by using
a. Integrator
b. Inverted Amplifier
c. Non - Inverted Amplifier
d. Diff Amplifier
60. Transformer humming due to
a. Vibration in Lamination
b. vibration in oil
61. If fuse rate = 8 Ampere, what does mean?
62. First line in transmission
a. Ground
b. R-phase
c. B-phase
d. Neutral
63. Circuit breaker is
a. Current interrupting device
b. Power factor detection device
64. Incandescent lamp operating at a power factor of
a. Leading
b. Lagging
c. Unity
d. Zero
65. Terminal represents control input of BJT
a. Emitter
b. Base
c. Collector
66. Transducers convert physical quantity into
a. Electrical
67. Sensor transducers will transfer.
a. Move to electrical signals
b. Heat to mechanical signal.
68. Sensor transducers(temp, motion, etc) will transfer to what type of signals
a. Electrical signal
b. mechanical signal
69. Common breakers used in distribution level
a. Air circuit breaker ACB
b. Oil type
c. Vacuum VCB
70. Difference between MOSFET and BJT
a. MOSFET amplifies current
b. BJT is bigger in size and dimensions
71. What is the DC gain of the transistor NPN?
a. The right answer is IC/IB, they put also the formulas of the MOSFET which are wrong for
this question
72. How the diode let pass the current?
a. Only in one way, it will block the other way
73. Terminals of a transistor (BJT):
a. Base, collector & emitter
b. gate, collector & emitter
c. gate, emitter & drain
74. Differential Amplifier with High CMRRS means:
a. High rejection of noise
b. Amplify noise
c. High amplification gain
75. Op-amp (operational amplifier) input resistance:
a. Zero
b. Infinity
c. Relative resistance
d. Same output resistance.
76. Which of the following devices has a metalsemiconductor junction formed between a metal and a
semiconductor:
a. schottky diode
b. zener diode
c. varactor diode
d. tunnel diode
77. CMOS inverter is superior to the R-pull up inverter due to:
a. High impedance
b. Smaller propagation delay
c. Symmetric transfer characteristics
78. Inverter allowed noise level question given the values of VOH, VOL, VIH, VIL. And need to get
NMH and NML
79. To get rid of DC offset use?
a. Low pass filter
b. high pass filter
c. Band pass filter
d. Stop band pass filter
80. For forward biasing
a. Anode 3v cathode 7v
b. Anode 5v cathode 3v
c. Anode 7v cathode 10v
81. Amplifier working with good gain in?
a. Reverse region
b. Cutoff region
c. Active region
d. Saturated region
82. What is MOSFET
a. Transistor
b. Thyristors
c. Amplifier
83. What is the efficiency of
BJT = IC/IB
84. What is the power consumption of BJT
a. 15%
85. Ripple Factor of Zener Diode Depends on:
a. Zener Voltage
b. I/P Impedance
c. O/P Impedance
d. None of the above
86. A passive filter can
a. filter only
b. filter & amplify only
c. amplify only
d. none of the above
87. I/P side of the GSM Network should contain?
a. Low Pass Filter
b. High Pas Filter
c. Band Pass Filter
d. None of the above
88. Lower current frequency of an NPN transistor depends on
a. Input Imp
b. OP/P imp
c. System Voltage
d. All of the above
130. BJT acts as a switch in:
a. Linear Region
b. Saturation Region
c. Active Region
131. Cascaded amplifier used to reduce load effect, the output impedance will be
a. High
b. Low
c. Medium
89. To minimized loading effect used.
a. Inverter amplifier
b. Non inverter amplifier
c. Integrator
90. BJT will act as a switch in which region
a) Ohmic Region
b) Saturation Region
c) Active Region
d) Passive Region
91. For an inverter op-amp, what will be the equivalent output resistance?
a. Relative forward resistance
b. Infinity
c. 0
d. Same as the input resistance
e. None of the above
92. In order to have minimum loading effect, output impedance of a cascade amplifier must be
a. High
b. Low
c. Medium
93. Which one will be true for an active filter
a. Filter only
b. Filter & amplify only
c. Amplify only
d. None of the above
94. Ripple Factor of Zener Diode Depends on.
a. Zener Voltage
b. I/P Impedance
c. O/P Impedance
d. None of the above
3) GENERAL &NON ELECTRICAL QUESTIONS:
182. If Water to cement ratio used in a residential building higher , then what will be the effect
on building
a) Strength will be low
b) Strength will be high
c) Pouring will be faster
d) Pouring will be Slower
e) No effect
184. Coefficient of performance of a refrigerator that consumes 800 watts of power to remove
heat at a rate of 5 BTU per second.
a. 4.6
b. 6.6 ( 5 x 1055/800 = 6.6) ( where 1BTU=1055 j) & ( 1 watt = 1j/s)
c. 8.2
d. 3.5
186. In what situation we can claim for a change order from the client
a) When client want to add something which is not available in initial scope
b) When major change occurs due to site conditions
c) Design mistake or Error
d) All of the above
187. Humming happening in a Transformer due to
a) Due to the Vibration in brush
b) Due to magnetostriction in core laminations
c) Due to the Vibration in winding
d) None of the above
e) All of the above
192. Surge voltage originate in a power system due to
a) Lightning
b) Switching operations
c) Faults
d) Any of the above
194. The term Pipe lining is used to indicate