Académique Documents
Professionnel Documents
Culture Documents
Issue 02
Date 2017-04-27
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Contents
2 Overview......................................................................................................................................... 4
2.1 Introduction.................................................................................................................................................................... 4
2.2 Benefits........................................................................................................................................................................... 6
2.3 Related Concepts............................................................................................................................................................ 6
2.4 Architecture.................................................................................................................................................................... 6
3 Technical Description...................................................................................................................8
3.1 Selection of a Coordinating Cell Set.............................................................................................................................. 9
3.2 Selection of CoMP UEs and Coordinating Cells............................................................................................................9
3.2.1 Entering the DPS Mode............................................................................................................................................... 9
3.2.2 Entering the JT Mode................................................................................................................................................ 11
3.2.3 Exiting the DPS or JT Mode......................................................................................................................................11
3.3 Multi-Cell Coordinated Transmission.......................................................................................................................... 12
4 Related Features...........................................................................................................................13
5 Network Impact........................................................................................................................... 16
6 Engineering Guidelines............................................................................................................. 17
6.1 When to Use................................................................................................................................................................. 17
6.2 Required Information................................................................................................................................................... 17
6.3 Planning........................................................................................................................................................................ 21
6.3.1 RF Planning............................................................................................................................................................... 21
6.3.2 Network Planning...................................................................................................................................................... 21
6.3.3 Hardware Planning.................................................................................................................................................... 21
6.4 Deployment.................................................................................................................................................................. 21
6.4.1 Process....................................................................................................................................................................... 21
6.4.2 Requirements............................................................................................................................................................. 22
6.4.3 Precautions.................................................................................................................................................................22
7 Parameters..................................................................................................................................... 32
8 Counters........................................................................................................................................ 44
9 Glossary......................................................................................................................................... 52
10 Reference Documents............................................................................................................... 53
1.1 Scope
This document describes LAOFD-120201 DL CoMP (Trial), including its technical
principles, related features, network impact, and engineering guidelines.
Any parameters, alarms, counters, or managed objects (MOs) described herein apply only to
the corresponding software release. For future software releases, refer to the corresponding
updated product documentation.
This document applies only to LTE FDD. Any "LTE" in this document refers to LTE FDD,
and "eNodeB" refers to LTE FDD eNodeB.
l Feature change
Changes in features and parameters of a specified version as well as the affected entities
l Editorial change
Changes in wording or addition of information and any related parameters affected by
editorial changes. Editorial change does not specify the affected entities.
eRAN12.1 02 (2017-04-27)
This issue includes the following changes.
eRAN12.1 01 (2017-03-08)
This issue includes the following changes.
2 Overview
2.1 Introduction
In 3GPP releases earlier than 3GPP Release 11, physical downlink shared channel (PDSCH)
data of LTE cell edge users (CEUs) cannot be sent with the help of adjacent cells to improve
the performance of CEUs. This gain can be achieved by downlink coordinated multipoint
transmission (DL CoMP) based on TM10 introduced in 3GPP Release 11.
DL CoMP enables multiple cells to cooperate to perform downlink transmission. DL CoMP is
implemented based on TM10 introduced in 3GPP Release 11. Multiple cells cooperate based
on ideal backhaul (intra-BBU backhaul or backhaul based on multi-BBU interconnection
through USUs) to process and transmit PDSCH data by using antennas of neighboring cells.
USU refers to universal switching unit. Downlink transmission by multiple cells adopts two
modes, dynamic point selection (DPS) and joint transmission (JT), to improve hotspot cell
capacity or CEU performance. eNodeBs can adaptively select an appropriate transmission
mode based on the cell load and channel quality.
DPS
In DPS mode, the coordinating cell sends PDSCH data to the UE to increase the hotspot cell
capacity, CEU throughput, and average UE throughput.
Figure 2-1 illustrates the DPS mode, in which PDCCH data of the UE is sent by cell 1 (the
serving cell), and PDSCH data is sent by cell 1 to cell 2 (the coordinating cell) and then sent
by cell 2 to the UE.
JT
In JT mode, both the serving cell and coordinating cell transmit PDSCH data to improve the
throughput of CEUs with a low signal to interference plus noise ratio (SINR).
Figure 2-2 illustrates the JT mode, in which
l PDCCH data of the UE is sent by cell 1 (the serving cell), and PDSCH data is sent by
cell 1 to cell 2 (the coordinating cell). Cell 1 and cell 2 allocate the same RBs to send
PDSCH data to the UE.
l The UE receives the same PDSCH data from cell 1 and cell 2 simultaneously.
Figure 2-2 JT
2.2 Benefits
DL CoMP improves the downlink throughput and user experience of CEUs.
l DPS increases the capacity of hotspot cells and improves the CEU throughput and
average UE throughput when the network load is heavy and imbalanced.
l JT improves the throughput of CEUs with a low SINR when the network load is light.
Coordinating cell A set of 10 neighboring cells that cause the strongest interference to
set of the serving the serving cell as measured by the eNodeB
cell
Coordinating cell The eNodeB identifies the coordinating cells for a DPS or JT UE
of a DPS or JT UE based on the event A3 measurement report sent by the DPS or JT UE.
The coordinating cells of a UE belong to the coordinating cell set of
the serving cell of the UE.
2.4 Architecture
DL CoMP is implemented through the cooperation of the U2000, USU, eNodeB, and UE.
Figure 2-3 to Figure 2-5 show the networking diagrams. If DL CoMP is performed among
BBUs, time synchronization is required across the entire network.
Table 2-2 describes the functions of the network elements (NEs) shown in Figure 2-3 to
Figure 2-5.
3 Technical Description
Figure 3-1 shows the DL CoMP process, including selection of a coordinating cell set,
selection of CoMP UEs and coordinating cells, and multi-cell coordinated transmission.
As shown in Figure 3-2, when the PRB usage of the serving cell is greater than the
threshold specified by the CellDlCompAlgo.DpsServingCellDlPrbThd parameter and
the serving cell is a macro cell, the eNodeB selects the serving cell as the DPS serving
cell.
2. The eNodeB selects the cells with the strongest RSRP in the coordinating cell set as
coordinating cells.
If the RSRP value of a neighboring cell minus that of the serving cell of a UE is greater
than or equal to the coordinating cell RSRP threshold plus the coordinating cell RSRP
offset, the UE reports event A3. If the neighboring cell that meets the event A3 reporting
conditions belongs to the coordinating cell set, it is selected as a coordinating cell.
In HomNet networking scenarios, the coordinating cell RSRP threshold is specified
by the CellDlCompAlgo.HomnetDpsCoCellRsrpThd parameter, and only the
macro cells with the strongest RSRP in the coordinating cell set can be selected as
coordinating cells.
In HetNet scenarios, the coordinating cell RSRP threshold is specified by the
CellDlCompAlgo.HetnetDpsCoCellRsrpThd parameter, and only the micro cells
with the strongest RSRP in the coordinating cell set can be selected as coordinating
cells.
In HomNet and HetNet hybrid networking scenarios, the micro cells with the
strongest RSRP in the coordinating cell set are preferentially selected as
coordinating cells.
NOTE
The system automatically configures the coordinating cell RSRP offset to prevent ping-pong
configuration of TM10 for UEs.
3. The eNodeB selects DPS UEs.
If the coordinating cells selected in 2 meet all of the following conditions, the eNodeB
selects the UEs as DPS UEs and configures the TM10 mode for them.
The PRB usage of the serving cell minus the PRB usage of a coordinating cell is
greater than the value of the CellDlCompAlgo.DpsLoadDiffThd parameter.
The number of UEs in RRC_CONNECTED mode in a coordinating cell divided by
the number of UEs in RRC_CONNECTED mode in the serving cell is less than or
The system automatically configures the coordinating cell RSRP offset to prevent ping-pong
configuration of TM10 for UEs.
3. The eNodeB selects JT UEs.
If the coordinating cells selected in 2 meet both of the following conditions, the eNodeB
selects the UEs as JT UEs and configures the TM10 mode for them.
The PRB usage of a coordinating cell is less than the value of the
CellDlCompAlgo.JtCoCellDlPrbThd parameter.
The spectral efficiency for the CQIs reported by the UEs is less than that for CQIs 5
and 8 in the case of single-codeword transmission. For details about CQIs 5 and 8,
see Table 7.2.3-1 4-bit CQI Table and Table 7.2.3-2 4-bit CQI Table 2 in section
7.2.3 "Channel Quality Indicator (CQI) definition" in 3GPP TS 36.213 V12.9.1.
4 Related Features
Prerequisite Features
Feature ID Feature Name Description
LOFD-001007 High Speed Mobility In high speed mobility scenarios, the channel
conditions and load status of a cell change so
LOFD-001008 Ultra High Speed rapidly that DL CoMP cannot respond
Mobility promptly.
LOFD-001009 Extended Cell Access In DL CoMP, UEs need to receive data from
Radius different cells simultaneously. Therefore, DL
CoMP does not apply to extended coverage
LOFD-001031 Extended CP scenarios.
Impacted Features
Feature ID Feature/Function Description
Name
LOFD-001070 Symbol Power Saving When both DL CoMP and enhanced symbol
power saving are enabled, enhanced symbol
power saving is not triggered during DL
CoMP coordinating cell scheduling.
5 Network Impact
System Capacity
DL CoMP is implemented using TM10. CSI-RSs need to be configured (in the
CellCsiRsParaCfg MO) in cells when DL CoMP is enabled. However, CSI-RSs will result in
a loss of system capacity. The more REs occupied by CSI-RSs indicate the shorter subframe
period and greater loss.
Network Performance
DL CoMP has the following impact on network performance:
l When DPS takes effect, PDSCH data of CEUs in the heavily loaded serving cell are
offloaded to coordinating cells. In this way, more resources are available for UEs in the
serving cell, and the user-perceived downlink throughput in the serving cell increases. If
the increase of resources for DPS UEs in the lightly loaded coordinating cells cannot
compensate for the loss of channel quality deterioration, the user-perceived downlink
throughput of the DPS UEs decreases.
l HomNet networking: When the PRB usage of the heavily loaded cell is 60%, DL CoMP
increases the CEU throughput by 5% to 10% and the average UE throughput by up to
5%.
l HetNet networking: When a macro cell includes four micro cells and the PRB usage of
the macro cell is 60%, DL CoMP increases the CEU throughput by about 20% and the
average UE throughput by about 10%.
l When the PRB usage of a cell is 10%, DL CoMP increases the throughput of JT UEs by
about 10%. The CEU throughput increase depends on the ratio of JT UEs to CEUs. If
both the DL CoMP and CSI-RS switches are turned on when there are a few JT UEs,
CSI-RS subframe configuration will decrease the average UE throughput.
l DL CoMP uses more PRB resources to increase the average PRB usage, increasing
interference of neighboring cells. In this case, the measured CQI value and the
proportion of rank 2 of CEUs may decrease slightly.
l When the UnCfgCsiRsUEDeOrderSchSwitch(UnCfgCsiRsUEDeOrderSchSwitch)
check box under the CellDlschAlgo.CsiRsSfSchStrSwitch parameter is cleared, UEs not
supporting TM9 or TM10 are not scheduled in CSI-RS subframes. The perceived
throughput of such UEs will decrease by 0% to 5%. When this check box is selected,
UEs not supporting TM9 or TM10 can be scheduled in CSI-RS subframes by using
lower MCS indexes. The perceived throughput of such UEs will increase by 0% to 3%.
6 Engineering Guidelines
Among the following listed counters, counters related to CEUs are available only when the
BasedA3EdgeUserSwitch(BasedA3EdgeUserSwitch) check box under the
CellCounterParaGroup.CellCounterAlgoSwitch parameter is selected. CEUs can be identified
based on the CellCounterParaGroup.EdgeUserA3Offset parameter. CEUs with weak coverage
can be identified based on the CellCounterParaGroup.EdgeUserServRSRPThd parameter.
Before activating DL CoMP, run the following command:
MOD CELLCOUNTERPARAGROUP:LocalCellId=0,
CellCounterAlgoSwitch=BasedA3EdgeUserSwitch-1, EdgeUserA3Offset=-6;
Network load is indicated by the counters listed in Table 6-1 and Table 6-2.
Table 6-2 Counters related to the average number of PRBs used in the downlink
Counter Counter Name Description
ID
Network interference and coverage performance are indicated by the counters listed
in Table 6-3 to Table 6-8.
Table 6-4 Counters related to the number of times each MCS index is selected for
PDSCH scheduling
Counter Counter Name Description
ID
Table 6-5 Counters related to the number of times full bandwidth CQIs 0 to 15 are
reported in a cell
Counter Counter Name Description
ID
Table 6-6 Counters related to the number of times ranks 1 to 4 are reported by UEs
in a cell
Counter Counter Name Description
ID
Table 6-7 Counters related to the average downlink rate of UEs in a cell
Counter Counter Name Description
ID
6.3 Planning
6.3.1 RF Planning
N/A
6.4 Deployment
6.4.1 Process
The DL CoMP deployment process is as follows:
1. Enable automatic measurement of neighboring cell downlink RSRP.
2. Perform time synchronization configuration in Cloud BB scenarios.
3. Configure the parameters of the cells for which DL CoMP is to be enabled.
4. Turn on the DL CoMP switch.
6.4.2 Requirements
Other Features
For details, see 4 Related Features.
Hardware
l Baseband processing unit: The LBBPc does not support this feature.
l USU: A USU3910 is required when inter-BBU DL CoMP is to be enabled.
l RRU: Low-power RRUs, such as mRRU3220E and mRRU3230E, which do not support
1T1R or 1T2R, are used for micro cells involved in DL CoMP.
License
None
Other Requirements
This feature requires support from UEs. UEs must be compliant with 3GPP Release 11 or
later and capable of TM10 multi-CSI measurement.
6.4.3 Precautions
l All cells with DL CoMP enabled must have the same DL CoMP configurations.
l DL CoMP is implemented using TM10. CSI-RSs must be configured (in the
CellCsiRsParaCfg MO) in all involved cells when DL CoMP is enabled.
The following table describes the parameters that must be set in the CellDlCompAlgo MO to
configure the thresholds for DL CoMP.
The following table describes the parameters that must be set in the NCellDlRsrpMeasPara
MO for coordinating cell set measurement.
The following table describes the parameters that must be set in the CellCsiRsParaCfg MO
for the CSI-RS.
The following table describes the parameters that must be set in the CellDlschAlgo MO for
downlink scheduling.
The following table describes the parameter that must be set in the CellUlschAlgo MO for
uplink scheduling.
Step 2 Run the MOD NCELLDLRSRPMEASPARA command to turn on the cell-level automatic
neighboring cell downlink RSRP measurement switch.
Step 3 Run the MOD CELLALGOSWITCH command to turn on the DL CoMP algorithm switch.
Step 5 Run the MOD CELLDLSCHALGO command with the downlink scheduling-related
parameters specified.
Step 6 Run the MOD CELLDLCOMPALGO command to modify cell-level DL CoMP parameters.
Step 7 Run the MOD CELLULSCHALGO command with the uplink scheduling-related
parameters specified.
----End
Step 1 On the eNodeB side, run the DSP CELLDLCOMPCOCELLS command to query the value
of Cell DL CoMP Property.
Expected result: The value of Cell DL CoMP Property is DLCOMP_DPS or
DLCOMP_JT.
Step 2 Log in to the U2000 and choose Monitoring > Signaling Trace > Signaling Trace
Management. In the displayed window, choose Cell Performance Monitoring > DL CoMP
Monitoring in the navigation tree. In the displayed dialog box, select the target eNodeBs and
create a DL CoMP monitoring task that monitors the number of DL CoMP UEs in a cell that
are also scheduled in coordinating cells.
Expected result: The value of DPS Benefit User Number or JT Benefit User Number is not
zero. This result shows that DL CoMP has taken effect.
----End
6.4.7 Deactivation
This feature can be deactivated using the CME or MML commands.
Step 2 Run the MOD CELLALGOSWITCH command to turn off the DL CoMP algorithm switch.
Step 3 (Optional) If eCSPC and adaptive ICIC are not enabled, run the MOD
NCELLDLRSRPMEASPARA command to disable cell-level automatic downlink
neighboring cell RSRP measurement.
----End
6.4.8 Reconfiguration
N/A
Using Counters
Compare the performance counters before and after DL CoMP is enabled.
Observe the following indicators before and after activating DL CoMP. The changes in the
values reflect DL CoMP gains.
NOTE
Before observing the downlink average user-perceived rate and the user-perceived rate at the cell edge,
run the MOD CELLCOUNTERPARAGROUP command to turn on related switches related to cell-
level performance measurement.
MML command example:
MOD
CELLCOUNTERPARAGROUP:LOCALCELLID=0,CELLCOUNTERALGOSWITCH=BasedA3EdgeUserSwitch
-1,EDGEUSERA3OFFSET=-12;
Step 1 Run the LST CELLALGOSWITCH command to check whether the DL CoMP algorithm
switch is turned on.
l If yes, go to Step 2.
l If no, configure parameters by referring to 6.4.5.1 Data Preparation.
Step 2 Run the DSP CELLDLCOMPCOCELLS command to check whether DL CoMP has taken
effect.
l If yes, go to Step 3.
l If no, check whether the local cell meets the DL CoMP threshold criteria, including user
proportion thresholds for CSI-RS configuration and unconfiguration and the PRB usage
threshold.
Step 3 Check the following performance counters to see whether the DPS or JT UE proportion is too
low, for example, lower than 15%.
Counter ID Counter Name Description
l If no, go to Step 4.
l If yes, the number of DPS and JT UEs is too small. In this case, DL CoMP cannot offer
noticeable gains to increase the capacity in terms of UE quantity and data rate.
Step 4 If the preceding steps fail to resolve the problem, contact Huawei technical support.
----End
7 Parameters
witch), FDDHetNetDlCompS-
witch(FDDHetNetDlCompSwitch)
Unit: None
Actual Value Range: IntraDlCompSwitch,
InterDlCompDcsSwitch, InterDlCompCbfSwitch,
FDDHomNetDlCompSwitch, FDDHetNetDlCompS-
witch
Default Value: IntraDlCompSwitch:Off,
InterDlCompDcsSwitch:Off, InterDlCompCbfS-
witch:Off, FDDHomNetDlCompSwitch:Off,
FDDHetNetDlCompSwitch:Off
NCellDl DlRsrp MOD LOFD-0 Coordin Meaning: Indicates whether to enable automatic
RsrpMe AutoNC NCELL 70208 ated downlink RSRP measurements on neighboring cells
asPara ellMeas DLRSR LAOFD Scheduli of the cell. This type of measurement is enabled only
Switch PMEAS -120201 ng based if this parameter is set to ON. This parameter applies
PARA Power only to LTE FDD.
LST Control GUI Value Range: OFF(Off), ON(On)
NCELL DL Unit: None
DLRSR CoMP
PMEAS Actual Value Range: OFF, ON
PARA Default Value: OFF(Off)
NCellDl NCellDl MOD LOFD-0 Coordin Meaning: Indicates the event A3 offset for automatic
RsrpMe RsrpMe NCELL 70208 ated neighboring cell downlink RSRP measurement. The
asPara asA3Off DLRSR LAOFD Scheduli signal quality of the neighboring cell must be offset
set PMEAS -120201 ng based better than that in the serving cell for a UE to report
PARA Power downlink RSRP of this neighboring cell. A larger
LST Control value of this parameter indicates a lower probability
NCELL DL that UEs report automatic neighboring cell downlink
DLRSR CoMP RSRP measurement results. This parameter applies
PMEAS only to LTE FDD.
PARA GUI Value Range: -30~30
Unit: 0.5dB
Actual Value Range: -15~15
Default Value: -12
CellDlC DpsServ MOD LAOFD DL Meaning: Indicates the threshold of the downlink PRB
ompAlg ingCell CELLD -120201 CoMP usage for a DPS serving cell when DL CoMP is
o DlPrbTh LCOMP enabled. When the PRB usage of a candidate cell
d ALGO exceeds this threshold, the cell can be selected as a
LST DPS serving cell. This parameter applies only to LTE
CELLD FDD cells.
LCOMP GUI Value Range: 0~100
ALGO Unit: %
Actual Value Range: 0~100
Default Value: 40
CellDlC Homnet MOD LAOFD DL Meaning: Indicates the RSRP offset threshold for DPS
ompAlg DpsCoC CELLD -120201 CoMP UEs in selecting a coordinating cell in a HomNet. A
o ellRsrpT LCOMP large value of this parameter indicates a high
hd ALGO requirement on neighboring cell quality for reporting
LST measurement events and a small number of DPS UEs
CELLD selecting a coordinating cell in a HomNet. A small
LCOMP value of this parameter indicates a large number of
ALGO DPS UEs selecting a coordinating cell in a HomNet.
This parameter applies only to LTE FDD cells.
GUI Value Range: -30~30
Unit: 0.5dB
Actual Value Range: -15~15
Default Value: -6
CellDlC HetnetD MOD LAOFD DL Meaning: Indicates the RSRP offset threshold for DPS
ompAlg psCoCel CELLD -120201 CoMP UEs in selecting a coordinating cell in a HetNet. A
o lRsrpTh LCOMP large value of this parameter indicates a high
d ALGO requirement on neighboring cell quality for reporting
LST measurement events and a small number of DPS UEs
CELLD selecting a coordinating cell in a HetNet. A small
LCOMP value of this parameter indicates a large number of
ALGO DPS UEs selecting a coordinating cell in a HetNet.
This parameter applies only to LTE FDD cells.
GUI Value Range: -30~30
Unit: 0.5dB
Actual Value Range: -15~15
Default Value: -12
CellDlC DpsLoa MOD LAOFD DL Meaning: Indicates the threshold of the difference
ompAlg dDiffTh CELLD -120201 CoMP between the PRB usage of a DPS serving cell and that
o d LCOMP of a DPS coordinating cell when DL CoMP is
ALGO enabled. When the difference exceeds this threshold,
LST the coordinating cell can function as the target cell of
CELLD DPS UEs. This parameter applies only to LTE FDD
LCOMP cells.
ALGO GUI Value Range: 0~50
Unit: %
Actual Value Range: 0~50
Default Value: 20
CellDlC DpsCoC MOD LAOFD DL Meaning: Indicates the threshold for the ratio of the
ompAlg ellUserR CELLD -120201 CoMP number of uplink synchronized UEs in a dynamic
o atioThd LCOMP point selection (DPS) serving cell to a DPS
ALGO coordinating cell when DL CoMP is enabled. When
LST the ratio of the number of uplink synchronized UEs in
CELLD the coordinating cell (including those transferred to
LCOMP the coordinating cell) to that in the serving cell is
ALGO smaller than this threshold, the coordinating cell can
function as the target cell of DPS UEs. This parameter
applies only to LTE FDD cells.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 50
CellDlC JtServin MOD LAOFD DL Meaning: Indicates the threshold of the downlink PRB
ompAlg gCellDl CELLD -120201 CoMP usage for a serving cell for joint transmission when
o PrbThd LCOMP DL CoMP is enabled. When the PRB usage of a
ALGO candidate cell is smaller than this threshold, the cell
LST can be selected as a serving cell for joint transmission.
CELLD This parameter applies only to LTE FDD cells.
LCOMP GUI Value Range: 0~100
ALGO Unit: %
Actual Value Range: 0~100
Default Value: 20
CellDlC JtCoCell MOD LAOFD DL Meaning: Indicates the RSRP offset threshold for joint
ompAlg RsrpThd CELLD -120201 CoMP transmission UEs in selecting a coordinating cell. A
o LCOMP large value of this parameter indicates a high
ALGO requirement on neighboring cell quality for reporting
LST measurement events and a small number of joint
CELLD transmission UEs. A small value of this parameter
LCOMP indicates a large number of joint transmission UEs.
ALGO This parameter applies only to LTE FDD cells.
GUI Value Range: -30~30
Unit: 0.5dB
Actual Value Range: -15~15
Default Value: -6
CellDlC JtCoCell MOD LAOFD DL Meaning: Indicates the threshold of the downlink PRB
ompAlg DlPrbTh CELLD -120201 CoMP usage for joint transmission UEs in selecting a
o d LCOMP coordinating cell when DL CoMP is enabled. When
ALGO the PRB usage of a candidate cell is lower than this
LST threshold, the cell can be selected as a coordinating
CELLD cell for joint transmission. This parameter applies only
LCOMP to LTE FDD cells.
ALGO GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 20
CellCsp CellCsp MOD LOFD-0 Coordin Meaning: Indicates whether to enable CSPC in the
cPara cSwitch CELLC 70208 ated cell. This parameter applies only to LTE FDD and
SPCPA TDLOF Scheduli LTE TDD.
RA D-08020 ng based GUI Value Range: OFF(Off), ON(On)
LST 3 Power
Control( Unit: None
CELLC
SPCPA Cloud Actual Value Range: OFF, ON
RA BB) Default Value: OFF(Off)
Coordin
ated
Scheduli
ng based
Power
Control
CellCsp CelleCs MOD LOFD-0 Coordin Meaning: Indicates whether to enable cell-level
cPara pcSwitc CELLC 70208 ated enhanced CSPC (eCSPC). eCSPC is enabled only
h SPCPA Scheduli when this parameter is set to ON(On). This parameter
RA ng based applies only to LTE FDD.
LST Power GUI Value Range: OFF(Off), ON(On)
CELLC Control
Unit: None
SPCPA
RA Actual Value Range: OFF, ON
Default Value: OFF(Off)
CellCou CellCou MOD LEOFD- Virtual Meaning: Indicates whether to enable cell-level
nterPara nterAlgo CELLC 111305 / 4T4R algorithms related to performance counters. This
Group Switch OUNTE LEOFD- Adaptiv parameter includes the following options:
RPARA 111305 e Inter- BasedA3EdgeUserSwitch: Indicates whether to enable
GROUP LOFD-0 Cell A3-based cell edge user (CEU) identification. If this
LST 60201 Interfere option is selected, the eNodeB starts to identify CEUs
CELLC nce based on A3-related measurement reports and collects
LOFD-0 related performance counters based on the identified
OUNTE 70208 Coordin
RPARA ation CEUs. This option applies only to LTE FDD and LTE
GROUP TDD.
Coordin
ated GUI Value Range:
Scheduli BasedA3EdgeUserSwitch(BasedA3EdgeUserSwitch)
ng based Unit: None
Power Actual Value Range: BasedA3EdgeUserSwitch
Control
Default Value: BasedA3EdgeUserSwitch:Off
CellCou EdgeUs MOD LEOFD- Virtual Meaning: Indicates the offset for cell edge user (CEU)
nterPara erA3Off CELLC 111305 4T4R identification event A3. This offset is the difference
Group set OUNTE LOFD-0 Adaptiv between the signal quality of a neighboring cell and
RPARA 60201 e Inter- that of the serving cell. A larger value of this
GROUP Cell parameter results that better signal quality of the
LOFD-0 neighboring cell is required for the reporting of CEU
LST 70208 Interfere
CELLC nce identification event A3 and the eNodeB has a lower
OUNTE Coordin probability of identifying a UE as a CEU. A smaller
RPARA ation value of this parameter results in a higher probability
GROUP that a UE is identified as a CEU. This parameter
Coordin applies only to LTE FDD and LTE TDD.
ated
Scheduli GUI Value Range: -30~30
ng based Unit: 0.5dB
Power Actual Value Range: -15~15
Control
Default Value: -13
CellCou EdgeUs MOD None None Meaning: Indicates the serving cell RSRP threshold
nterPara erServR CELLC for determining CEUs when the
Group SRPThd OUNTE BasedA3EdgeUserSwitch option of the
RPARA CellCounterAlgoSwitch parameter is selected. A
GROUP larger value of this parameter indicates a higher
LST probability of identifying a UE as a CEU. A smaller
CELLC value of this parameter indicates a lower probability
OUNTE of identifying a UE as a CEU. The value 255 indicates
RPARA that the serving cell RSRP is not used in the
GROUP identification. This parameter applies only to LTE
FDD and LTE TDD.
GUI Value Range: -140~-43,255
Unit: dBm
Actual Value Range: -140~-43,255
Default Value: 255
CellCsi CsiRsS MOD TDLOF DL 4*2 Meaning: Indicates whether to configure CSI-RSs for
RsParaC witch CELLC D-00100 MIMO UEs. If this parameter is set to NOT_CFG(Not
fg SIRSPA 3 DL 2- configure), the eNodeB does not configure CSI-RSs
RACFG TDLAO Layer for UEs. If this parameter is set to FIXED_CFG(Fixed
LST FD-001 MIMO configure), the eNodeB configures CSI-RSs for UEs
CELLC 00114 Based that support CSI-RSs. If this parameter is set to
SIRSPA on TM9 ADAPTIVE_CFG(ADAPTIVE_CFG), the eNodeB
TDLAO determines whether to configure CSI-RSs for UEs that
RACFG FD-081 DL 4- support CSI-RSs based on the proportion of TM9
409 Layer UEs. When SfnLoadBasedAdptSwitch is deselected in
MIMO a TDD cell with adaptive SFN enabled, neither
Based FIXED_CFG nor ADAPTIVE_CFG takes effect. This
on TM9 parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: NOT_CFG(Not configure),
FIXED_CFG(Fixed configure),
ADAPTIVE_CFG(ADAPTIVE_CFG)
Unit: None
Actual Value Range: NOT_CFG, FIXED_CFG,
ADAPTIVE_CFG
Default Value: NOT_CFG(Not configure)
CellCsi CsiRsPe MOD LAOFD DL 2*2 Meaning: Indicates the channel state information
RsParaC riod CELLC -080210 MIMO (CSI) reference signal (RS) measurement period. This
fg SIRSPA LAOFD based on parameter applies only to LTE FDD and LTE TDD.
RACFG -080205 TM9 GUI Value Range: ms5(ms5), ms10(ms10),
LST / DL 4*2 ms20(ms20), ms40(ms40), ms80(ms80)
CELLC TDLAO MIMO Unit: None
SIRSPA FD-001 based on
RACFG 00113 TM9 Actual Value Range: ms5, ms10, ms20, ms40, ms80
CellCsi CsiRsCo MOD LOFD-0 DL 2*2 Meaning: Indicates the threshold of the proportion of
RsParaC nfigUser CELLC 01001 MIMO RRC_CONNECTED UEs supporting CSI_RS that is
fg RatioTh SIRSPA LOFD-0 DL 4*2 used to determine a change from the CSI-RS
RACFG 01003 MIMO unconfigured state to the CSI-RS configured state
LST when adaptive CSI-RS configuration is adopted. This
LOFD-0 DL 4x4 parameter applies only to LTE FDD and LTE TDD.
CELLC 01060 MIMO
SIRSPA GUI Value Range: 0~100
RACFG TDLAO DL 2-
FD-001 Layer Unit: %
00114 MIMO Actual Value Range: 0~100
TDLAO Based Default Value: 50
FD-081 on TM9
409 DL 4-
Layer
MIMO
Based
on TM9
CellCsi CsiRsU MOD LOFD-0 DL 2*2 Meaning: Indicates the threshold of the proportion of
RsParaC nconfig CELLC 01001 MIMO RRC_CONNECTED UEs supporting CSI_RS that is
fg UserRati SIRSPA LOFD-0 DL 4*2 used to determine a change from the CSI-RS
oTh RACFG 01003 MIMO configured state to the CSI-RS unconfigured state
LST when adaptive CSI-RS configuration is adopted. This
LOFD-0 DL 4x4 parameter applies only to LTE FDD and LTE TDD.
CELLC 01060 MIMO
SIRSPA GUI Value Range: 0~100
RACFG TDLAO DL 2-
FD-001 Layer Unit: %
00114 MIMO Actual Value Range: 0~100
TDLAO Based Default Value: 40
FD-081 on TM9
409 DL 4-
Layer
MIMO
Based
on TM9
CellDlsc MbsfnSf MOD LAOFD DL 2*2 Meaning: Indicates whether to configure Multimedia
hAlgo Cfg CELLD -080210 MIMO Broadcast multicast service Single Frequency
LSCHA LAOFD based on Network (MBSFN) subframes. The ten options of this
LGO -080205 TM9 parameter map to the ten MBSFN subframes. If an
LST DL 4*2 option is selected, the corresponding subframe is
CELLD MIMO configured. If an option is not selected, the
LSCHA based on corresponding subframe is not configured. PDSCH
LGO TM9 services with enhanced MIMO applied can be
scheduled on configured MBSFN subframes. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: SubFrame0(SubFrame0),
SubFrame1(SubFrame1), SubFrame2(SubFrame2),
SubFrame3(SubFrame3), SubFrame4(SubFrame4),
SubFrame5(SubFrame5), SubFrame6(SubFrame6),
SubFrame7(SubFrame7), SubFrame8(SubFrame8),
SubFrame9(SubFrame9)
Unit: None
Actual Value Range: SubFrame0, SubFrame1,
SubFrame2, SubFrame3, SubFrame4, SubFrame5,
SubFrame6, SubFrame7, SubFrame8, SubFrame9
Default Value: SubFrame0:Off, SubFrame1:Off,
SubFrame2:Off, SubFrame3:Off, SubFrame4:Off,
SubFrame5:Off, SubFrame6:Off, SubFrame7:Off,
SubFrame8:Off, SubFrame9:Off
CellUlsc DopMea MOD LBFD-0 Dynami Meaning: Indicates the Doppler measurement level,
hAlgo sLevel CELLU 0101502 c which is used for selecting a Doppler measurement
LSCHA / Scheduli policy. If this parameter is set to CLASS_0, the
LGO TDLBF ng demodulation reference signal (DMRS) whose signal
LST D-00101 to interference plus noise ratio (SINR) is greater than
CELLU 502 or equal to 5 dB is used in Doppler measurement. If
LSCHA this parameter is set to CLASS_1, the DMRS whose
LGO SINR is greater than or equal to 5 dB is used in
Doppler measurement. This parameter does not take
effect on cells established on an LBBPc. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: CLASS_0(CLASS_0),
CLASS_1(CLASS_1)
Unit: None
Actual Value Range: CLASS_0, CLASS_1
Default Value: CLASS_0(CLASS_0)
8 Counters
9 Glossary
10 Reference Documents