Académique Documents
Professionnel Documents
Culture Documents
Installation Instructions.
Navigation system with on-board monitor retrofit
BMW X3 (E 83)
These installation instructions are only valid for cars without SA 358 (climate comfort
windscreen)
Installation time
The installation time is 5.5 hours, but this may vary depending on the condition of the car and the
equipment in it.
Important information
These installation instructions are primarily designed for use within the BMW dealership organisation
and by authorised BMW service companies.
In any event the target group for these installation instructions is specialist personnel trained on BMW
cars with the appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals
and work instructions in a rational order using the prescribed tools (special tools) and observing current
health and safety regulations.
To avoid unnecessary extra work and/or costs, if any installation or function problems occur,
after a brief troubleshooting session (approx. 0.5 hours), an inquiry is to be sent straight away to
the technical parts support via the Aftersales Assistance Portal (ASAP), quoting the chassis
number, the part number of the retrofit kit and a precise description of the problem.
Ensure that the cables/lines are not kinked or damaged as you install them in the car. The costs incurred
as a result of this will not be reimbursed by BMW AG.
Additional cables/lines that you install must be secured with cable ties.
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used.
All the figures show LHD cars, proceed in exactly the same way on RHD cars.
After the installation work the retrofit kit must be programmed / coded using DISPlus or GT-1 via the CIP
path.
Pictograms
Denotes instructions that draw your attention to special features.
Ordering instructions
The CID control is not included in the retrofit kit and must be ordered separately (see EPC for part
number and documentation).
The wiring harness between the CD changer and CID control is not included in the retrofit kit and must
be ordered separately (see EPC for part number and documentation).
SA 672 CD changer
SA 692 CD changer preparation
1. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Connection diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
A B
D
E
H I J K
F
G
O P
L M N
083 0498 Z
Legend
TIS No.
Conduct a brief test ---
Disconnect the negative pole of the battery 12 00 ...
A1 A
A10
A2
A9
A3
A4 A5 A6 A7 A8
O1 O2
083 0499 Z
Item Description Signal Cable colour / Connection location in the car Abbreviation /
Cross-section Slot
A Wiring harness --- --- --- ---
A1 SW 8-pin plug casing --- --- Plug X322 X322
A2 8-pin socket casing SW --- --- Plug X322 X322
A3 18-pin socket casing WS --- --- CID C X18802
A4 Joint connector contact Reversing BL/GE Joint connector behind the glove X428
signal 0.75 mm2 compartment
A5 Open cable TAA SW/WS To the GE/GN cable from plug X11175 from X11175
0.35 mm2 the instrument cluster using an insulation- PIN 6
piercing connector M
A6 Socket contact NAV NF+ GE/RT CID control X13649
0.5 mm2 PIN 5
A7 Socket contact NAV NF- GE/BR CID control X13649
0.5 mm2 PIN 11
A8 Cable eyelet Terminal BR Earth post in the boot on the left X13200
31
A9 18-pin socket casing VI Navigation computer D X1312
--- ---
O Power supply cable --- --- For cars without SA 672 or SA 692 only ---
O1 Plug contact Terminal RT/GE Plug X322 X322
30 1.5 mm2 PIN 3
O2 Double flat spring contact Terminal RT/GE Fuse holder behind the glove compartment X10015
30 1.5 mm2 PIN 5
3 5
2 C
E A D
083 0362 Z
Legend
A Wiring harness
C CID
D Navigation computer
E GPS aerial
083 0385 Z
A7
083 0395 Z
A4
A1
X322 083 0365 Z
083 0500 Z
O2
P
083 0235 Z
All cars
X428 Connect branch A4 to joint connector X428, BL/
A4 GE cable.
If joint connector X428 is fully occupied,
connect branch A4 using an insulation-
M piercing connector M.
053 0631 Z
083 0393 Z
083 0369 Z
3 2
2
083 0370 Z
A3
083 0371 Z
083 0225 Z
L
083 0367 Z
A8
083 0391 Z
1
D
083 0368 Z
Do not insert the software CD into the navigation computer until prompted to do so during the
coding procedure (risk of damaging the navigation computer).
58g
2 4 5 8 7 1 6 3
FZV
R>47
30<42
30>39
30<49
30<41
I / K-Bus
A2*
58g
FZV
R<47
30<41
30<49
30<39
30<42
30<42
I / K-Bus
0,5 2,5 0,5 0,35 0,75 0,75 0,75 2,5 X10015
5 F42
A5* A4*
X18344
0,75
X812 WS RT GE
0,75
RT GE
X18802
8 11
A3*
30<49 I / K-Bus
A196
VMR VMR31 VMG VMG31 VMB VMB31 VMLC31 31
1 2 3 4 5 6 7 9
A112
NAF NF+ NAF NF- 31
9 18 10
X1313
0,5 0,5 A10*
GE RT GE BR 0,5
BR
5 11 X13649
X1091
Stand: 05.2004
NAF NF+ NAF NF- A6/A7*
0,5
N9 BR
X13200
083 0397 Z
A8*
14
10. Circuit diagram
Legend
N9 Radio
All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram.
Cable colours
BL Blue
BR Brown
GE Yellow
GN Green
GR Grey
RT Red
SW Black
VI Violet
WS White