Académique Documents
Professionnel Documents
Culture Documents
VS.RAB.AbnormRel.CS.RF
VS.RAB.AbnormRel.CS
VS.RAB.AbnormRel.CS.OM
VS.RAB.AbnormRel.CS.UTRANgen
VS.RAB.AbnormRel.CS.Preempt
VS.RAB.AbnormRel.CS.IuAAL2
VS.RAB.AbnormRel.PS.RF
VS.RAB.AbnormRel.PS
VS.RAB.AbnormRel.PS.OM
VS.RAB.AbnormRel.PS.Preempt
VS.RAB.AbnormRel.PS.GTPULoss
VS.SHO.FailRLAdd.CfgUnsupp
VS.SHO.FailRLAdd.ISR
VS.SHO.Fail.Cell
VS.SHO.FailRLAdd.InvCfg
VS.SHO.FailRLAdd.NoReply
VS.RAC.SHO.Fail.DLCE.Cong
IRATHO.FailRelocPrepOutCS.TAlExp
VS.IRATHO.FailRelocPrepOutCS.CNNoReply
IRATHO.FailRelocPrepOutCS.TgtFail
IRATHO.FailRelocPrepOutCS.ReloNoSup
IRATHO.FailRelocPrepOutCS.NoResAvail
IRATHO.FailRelocPrepOutCS
IRATHO.FailRelocPrepOutCS.UKnowRNC
VS.IRATHO.FailRelocPrepOutCS.Cancel
VS.IRATHO.FailRelocPrepOutCS.Abort
VS.IRATHO.FailRelocPrepOutCS.ReqInfoNotAvail
IRATHO.FailOutCS.PhyChFail
VS.IRATHO.FailOutCS
VS.IRATHO.FailOutCS.NoReply
VS.IRATHO.FailOutCS.Other
IRATHO.FailOutPSUTRAN.CfgUnsupp
IRATHO.FailOutPSUTRAN.PhyChFail
VS.IRATHO.FailOutPSUTRAN.Cell
VS.IRATHO.FailOutPSUTRAN.NoReply
VS.IRATHO.FailOutPSUTRAN.Other
Sub Items Level 2
VS.RAB.AbnormRel.CS.RF.SRBReset
VS.RAB.AbnormRel.CS.RF.ULSync
VS.RAB.AbnormRel.CS.RF.UuNoReply
VS.RAB.AbnormRel.PS.RF.UuNoReply
Description
Soft handover failure caused by other factors.
Number oft handover RL failures of the cells (the cause value is Configuration
Unsupported.)The UE thinks that the active set update contents of adding or
deleting links by the RNC are not supported.
Number of soft handover RL failures of the cells (the cause value is incompatible
simultaneous reconfiguration). The UE feeds back that the soft or softer handover
process of adding or deleting links by the RNC is not compatible with other
concurrent processes. The RNC ensures serial processing during the flow
processing. The problem is caused mainly because the processing of some UEs is
defective.
Number of soft handover RL failures of the cells (the cause value is invalid
configuration).The UE thinks that the active set update contents of adding or
deleting links by the RNC are invalid.
The RNC does not receive the response to the active set update command of
adding or deleting links. It is the main cause of soft or softer handover failure in the
network, and mainly occurs in the area where the coverage quality is poor or the
handover area is small.(radio related).
Description
SHO Admission Control fail due to UL power congestion
SHO Admission Control fail due to DL power congestion
SHO Admission Control fail due to Code congestion
SHO Admission Control fail due to UL Iub congestion
SHO Admission Control fail due to DL Iub congestion
SHO Admission Control fail due to HSUPA number limit
SHO Admission Control fail due to UL CE congestion
SHO Admission Control fail due to DL CE congestion
Description
Failure of inter-frequency hard handover because of other factors
Configuration unsupported
Physical channel failure
Incompatible simultaneous reconfiguration
Cell update occurred
Invalid configuration
No response on the air interface
Description
After the SRNC sends the RELOCATION REQUIRED, the SRNC starts the timer to
wait for the RELOCATION COMMAND message but the message is not received
when the timer times out. The possible causes are (1) CN configurations whether
inter-RAT handover is allowed. (2) RNC links and MSC links are abnormal.
The relocation fails in the target CN/RNC or in the system. Usually, the cause is as
follows:
The CN configurations are not correct.
The BSS does not support the relocation either the BSS allows inter-RAT
handover-in or the configurations of GSM neighboring cells are consistent with the
actual parameters.
Number of Failed Preparations for CS Outgoing Inter-RAT Handover for Cell
(Relocation not supported in Target RNC or Target system)
No resources are available. Usually, the BSC has no resources available for the
access of the UE or the 2G MSC has no information about the target cells.
Check the resource utilization of the 2G BSS. It is possible that no channel is
available because the channel is occupied by another subscriber.
Check the status of the target cell. The target cell may be faulty.
Check the mapping between the target cell and 2G MSC on the 3G MSC.
The target RNC is unknown. The cause is the main cause of relocation failure.
Usually, the reason is that the MSC cannot find the route leading to the 2G cells.
Check the CN configuration. It is possible that the LAI of the 2G target cell is not
configured on the MSC.
Check the consistency of the parameters of GSM neighboring cells configured on
the RNC.
After requesting the handover preparations, the RNC receives the release
command sent by the CN. It is usually caused as follows:
The inter-RAT handover request is initiated during the signaling (for example,
location update). Location update is complete before the flow is complete, so the
CN initiates the release.
The subscriber who sets up the call hangs up during the handover preparation, so
the CN initiates the release.
Number of CS Outgoing Inter-RAT Handover Preparation Failures due to operation
termination
Number of Failed CS Outgoing Inter-RAT Handover Preparations for Cell
(Requested Information Not Available)
Description
The handover is not supported by the configuration. Usually, the UE does not
receive the HANDOVER FROM UTRAN COMMAND message delivered by the
RNC because of the incorrect RNC format, incompatibility of the UE, or incorrect
configuration of the encryption parameters.
Description
The handover is not supported by the configuration. Usually, the UE does not
receive the CCO message delivered by the RNC because of the incorrect RNC
format, incompatibility of the UE, or incorrect configuration of the encryption
parameters.
After receiving the CCO message, the UE starts the T309 timer. The T309 timer is
stopped if the UE sets up a connection in a new cell. Once the T309 timer times out,
the original 3G cell is returned and the CCO failure message is sent.
Check the configuration of the GSM neighboring cell parameters. If the
parameters are not configured correctly, the access is initiated in an incorrect target
cell.
Check whether the status and KPIs of the target cell are normal.
Check the resource utilization of the target cell, and determine whether the access
failure is caused by the insufficiency of resources.
Check whether there exists strong interference in the GSM radio environment.
After sending the CCO message, the RNC starts the Trelocoverall timer. The timer
is stopped after the UE returns the CCO failure message or receives the IU
RELEASE CMD (the cause value is Normal release) message sent by the SGSN.
Once the timer times out, the RNC actively sends the IU RELEASE REQUEST
message to the SGSN. If receiving the SRNS Context Req message during the
period, the RNC restarts the timer.
Check whether the 2G SGSN allows the handover-in.
Check whether the RAU is complete after the UE accesses the 2G cell.
Other causes.
Description
RAB released by the RNC because of the downlink SRB reset due to poor coverage/quality.
RAB released by the RNC because of Uplink Synchronization Failure
RABs released by the RNC because of the Failure in the Radio Interface Procedure e.g SHO procedure. The failure
is usually caused by the imbalance between the uplink coverage and downlink coverage and fast signal change.
RABs released caused by the operation and maintenance work (for example, the cell is blocked).
RABs released caused by the UTRAN Generated Reason
RABs released caused by the high-priority preemption. Such call drop occurs when the load and resources are not
enough.
The RNC initiates abnormal release after finding that the AAL2 Path on the IU CS interface is abnormal
Description
RAB released by the RNC because of the downlink SRB reset due to poor coverage/quality.
RAB released by the RNC because of the downlink TRB reset due to poor coverage/quality.
RAB released by the RNC because of Uplink Synchronization Failure
RABs released by the RNC because of the Failure in the Radio Interface Procedure e.g SHO procedure.The failure
is usually caused by the imbalance between the uplink coverage and downlink coverage and fast signal change
RABs released caused by the operation and maintenance work (for example, the cell is blocked).
RABs released caused by the high-priority preemption. Such call drop occurs when the load and resources are not
enough.
The RNC initiates abnormal release after finding that the GTPU on the IU PS interface is abnormal
Measurement Item Sub Items Level 1
VS.RRC.FailConnEstab.Cong
VS.RRC.Rej.RL.Fail
VS.RRC.FailConnEstab.Cell
VS.RRC.Rej.TNL.Fail
VS.RRC.FailConnEstab.NoReply
VS.RAB.FailEstabCS.RNL
VS.RAB.FailEstabCS.Cell
VS.RAB.FailEstabCS.RNL
VS.RAB.FailEstabCS.Cell
VS.RAB.FailEstabCS.TNL
VS.RAB.FailEstabPS.RNL
VS.RAB.FailEstabPS.Cell
VS.RAB.FailEstabPS.TNL
VS.RAC.NewCallReq.Fail.HSUPANum.Cong
VS.RAC.NewCallReq.Preempt.Cong
VS.RAC.NewCallReq.Fail.ULCE.Cong
VS.RAC.NewCallReq-
VS.RAC.NewCallAcc
VS.RAC.NewCallReq.Fail.DLCE.Cong
VS.RAC.NewCallReq.Fail.ULPower.Cong
VS.RAC.NewCallReq.Fail.DLPower.Cong
VS.RAC.NewCallReq.Fail.Code.Cong
VS.RAC.NewCallReq.Fail.ULIUBBand.Cong
VS.RAC.NewCallReq.Fail.DLIUBBand.Cong
Sub Items Level 2 Description
VS.RRC.Rej.Code.Cong RRC Connection Setup reject due to DL code congestion
VS.RRC.Rej.ULCE.Cong RRC Connection Setup reject due to UL CE congestion
VS.RRC.Rej.DLCE.Cong RRC Connection Setup reject due to DL CE congestion
VS.RRC.Rej.ULIUBBand.Cong RRC Connection Setup reject due to UL Iub congestion
VS.RRC.Rej.DLIUBBand.Cong RRC Connection Setup reject due to DL Iub congestion
RRC Connection Setup reject due to UL power
VS.RRC.Rej.ULPower.Cong
congestion(RTWP or UL ENU)
RRC Connection Setup reject due to DL power
VS.RRC.Rej.DLPower.Cong
congestion(DL TCP or DL ENU)
VS.RAB.FailEstabCS.DLPower.Cong
VS.RAB.FailEstabCS.RBIncCfg
VS.RAB.FailEstabCS.RBCfgUnsup
VS.RAB.FailEstabCS.PhyChFail
VS.RAB.FailEstabCS.UuFail
VS.RAB.FailEstabCS.UuFail
VS.RAB.FailEstabCS.UuNoReply
VS.RAB.FailEstabCS.IubFail
VS.RAB.FailEstabPS.RBIncCfg
VS.RAB.FailEstabPS.RBCfgUnsupp
VS.RAB.FailEstabPS.PhyChFail
VS.RAB.FailEstabPS.UuFail
VS.RAB.FailEstabPS.UuNoReply
VS.RAB.FailEstabPS.IubFail
Description
Number of Failed Admissions Due to
HSDPA User Number Exceeding
Threshold During RAB Establishment for
Cell
Number of Failed Admissions Due to
HSUPA User Number Exceeding
Threshold During RAB Establishment for
Cell
Number of Preemptions During RAB
Establishment for Cell
Number of Failed Admissions Due to UL
CE congestion
Number of Failed Admissions Due to DL
CE congestion
Number of Failed Admissions Due to UL
Power congestion
Number of Failed Admissions Due to DL
Power congestion
Number of Failed Admissions Due to
Code congestion
Number of Failed Admissions Due to UL
Iub congestion
Number of Failed Admissions Due to DL
Iub congestion
Description
RAB Setup reject due to DL code congestion
RAB Setup reject due to UL CE congestion
RAB Setup reject due to DL CE congestion
RAB Setup reject due to UL Iub congestion
RAB Setup reject due to DL Iub congestion
RAB Setup reject due to UL power congestion(RTWP or UL ENU)
Description
RAB Setup reject due to DL code congestion
RAB Setup reject due to UL CE congestion
RAB Setup reject due to DL CE congestion
RAB Setup reject due to UL Iub congestion
RAB Setup reject due to DL Iub congestion
RAB Setup reject due to UL power congestion(RTWP or UL ENU)
RAB Setup reject due to DL power congestion(DL TCP or DL ENU)
In the RB setup phase, the UE returns the RB setup failure message.
The cause value is Invalid Configuration, cause by invalid
configurations of UE.