Académique Documents
Professionnel Documents
Culture Documents
EXSTREAMER
available for browser access as long as the device stays
STEP 1 powered.
Either use a network cable to link the Exstreamer and
the PC directly, or connect the Exstreamer to the PC STEP 6
100
via your network switch and power the device. Make To check if the Exstreamer is responding you can use
sure that you have a valid static IP address configured on the ping command again. To do so type ping 192.168.0.6
your PC (e.g. 192.168.0.2) and hit the Enter key. If you do get a reply the IP address
192.168.0.6 can be used to access the Exstreamer using a
STEP 2 web browser. Please go back to section 2 Network configura-
Windows : For a command window. click on Start, click tion by web browser to configure a static IP address. If you do
on Run.., in the Open field type cmd , click on OK.
OSX / Linux : Open a terminal window.
get request timed out then please repeat step 5 carefully (you
most likely mistyped the telnet command) or repeat the entire Quick Install Guide
Version 3.1
procedure. If the ARP method does not work for you, refer to
STEP 3 the user manual for further methods.
Please proceed to step 4 if you linked the PC directly to
the device in step 1. To ensure that you use a free IP
address (not already used by another device in the network) 4 Troubleshooting
please use the Ping command. To verify availability in
this example we assume the PC to have the IP address If the status LEDs (C) stay dark check the power Multiformat IP Audio Decoder
192.168.0.2 and want to check if 192.168.0.6 is free. cabling (installation step 3).
Type ping 192.168.0.6 and hit the Enter key. You C heck if the green LINK LED (I) is lit, if it is not then
should get no reply which gives you reasonable assertion check your network cabling (network port G)
that the pinged IP is available. If you have doubts about the current device settings
Package contents
you can revert the device to its factory defaults by
STEP 4 pressing the Reset button (A) until the red status LED a Exstreamer 100
Look for the Exstreamers MAC address printed on a (C) blinks rapidly (takes about 10 seconds). The device b Power supply
label on the bottom of the device (12 hex digits, separated will reboot once the button is released.
c RCA Stereo cable
by a hyphen every 2 digits). Type into the windows
command window For information about our products, manuals, technical
arp -s 192.168.0.6 00-08-E1-00-B1-77 documentation, latest firmware, support and access to Cable Set AUDIO (not included)
or on a OSX or Linux system type into the terminal the user forum please visit www.barix.com.
d Earphone
arp -s 192.168.0.6 00:08:E1:00:B1:77
and hit the Enter key (replace the digits according to your
e RCA Stereo cable
devices MAC address). You must have administrative rights f Network cable
to be able to do so (sudo on OSX / Linux). g Serial cable
Firmware
This device comes preloaded with standard firmware.
Alternative firmware can be downloaded from www.barix.com.
Support
For support please contact your local dealer or visit www.barix.com.
Barix AG, Seefeldstrasse 303, CH-8008 Zrich
P +41 43 433 22 11
info@barix.com, www.barix.com
Barix AG 3/2015, all rights reserved. All information is subject to change without notice. All mentioned trademarks belong
to their respective owners and are used for reference only. Barix, Exstreamer and SonicIP are trademarks of Barix AG, Switzerland,
and are registered in certain countries.
9 Not connected
* Pin 4 will provide 2.6V less than the supplied voltage on Vin+
(H) but not more than 12V.