Académique Documents
Professionnel Documents
Culture Documents
General Specifications
Toggles
Power Level: 10A @ 125/250V AC for JWM & JWMW models; 10A @ 30V DC for JWMW;
B 16A @ 125/250V AC for JWL & JWLW models; 5A @ 72V DC for telecommunication applications
Other Ratings
Contact Resistance: 10 milliohms maximum for JWM & JWMW; 20 milliohms maximum for JWL & JWLW
Pushbuttons
Environmental Data
Operating Temperature Range: 25C through +70C (13F through +158F) for JWM & JWL;
25C through +85C (13F through +185F) for panel seal JWMW & JWLW models
Humidity: 90 ~ 95% humidity for 96 hours @ 40C (104F)
Rotaries
Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Sealing: IP67 of IEC60529 standard for panel seal JWMW & JWLW models; dust resistant inner seal for others
Installation
Slides
Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section.
Standards & Certifications
Flammability Standards: UL94V-0 for rocker, housing, seal & case/base of JWL, JWM, JWMW & JWLW models
Tactiles
TV Ratings for UL & CSA: JWM (TV-5) Overload Test @ 120V AC for 50 operations:
Steady State Current (rms) 7.5A; Minimum Inrush Current (peak) 111A.
JWM (TV-5) Endurance Test @ 120V AC for 25,000 operations:
Steady State Current (rms) 5A; Minimum Inrush Current (peak) 78A.
JWL (TV-8) Overload Test @ 120V AC for 50 operations:
Steady State Current (rms) 12A; Minimum Inrush Current (peak) 163A.
Tilt
JWMW: add /U to end of part number to order UL mark on switch; add /CUL to end of part
number to order cULus mark on switch.
JWL: add /U-DC to end of part number to request UL rating on DC rated switch.
CSA: File No. 023535_0_000
Accessories
JWM & JWMW models certified at 10A @ 250V AC; JWL models certified at 16A @ 250V AC
VDE: License No. 115674
JWM models approved at steady state 5A, inrush 80A, resistive 10A, & motor load 6A all at
250V AC; JWL models approved at steady state inrush 128A, resistive 16A, & motor load 8A
Supplement
B40 www.nkkswitches.com
8/3/17
High Inrush 10 & 16 Amp Rockers Series JW
Distinctive Characteristics
Toggles
Rockers
Industrys first molded rocker with TV rating. Designed to handle large inrush current, B
with high electrical capacity of 10 and 16 Amps. JWM models certified for TV-5 rating
and JWL models for TV-8 rating.
Pushbuttons
JWMW and JWLW panel seal versions meet IP67 of
IEC60529 Standards (similar to NEMA 4 and 6).
Programmable Illuminated PB
Prominent external insulating barriers increase
insulation resistance and dielectric strength.
Keylocks
Increased electrical life with specially
designed plate to minimize contact bounce.
Rotaries
cover between actuator and contact area.
Slides
lock out flux, dust, and other contaminants.
Tactiles
with connector.
Tilt
Actual Size JWM
Touch
Indicators
Accessories
Supplement
www.nkkswitches.com B41
Series JW High Inrush 10 & 16 Amp Rockers
Toggles
JW LW 2 1 R A 1 A
Rockers
B
Pushbuttons
1 B Ivory B Ivory
SPDT
C Red H Gray
DPST
2 H Gray
DPDT
Notes: Note: JWMW & JWLW avail-
Rotaries
DPST must have international able with black or red caps only.
ON-OFF symbols for VDE
approval.
JWLW available in DPST &
DPDT only. Inscription
Slides
Orientation
No No Inscription IMPORTANT:
Code
Circuits Standard markings for JWM & JWL:
Tactiles
JWLW21RA1A
Black Housing
DPST
ON-NONE-OFF Circuit 16A @ 125/250V AC
Supplement
B42 www.nkkswitches.com
High Inrush 10 & 16 Amp Rockers Series JW
Toggles
RATINGS
Rockers
L Power Level 16A @ 125/250V AC
LW Panel Seal Power Level 16A @ 125/250V AC
B
Pushbuttons
Rocker Position Connected Terminals Throw & Schematics
Down Center Up Down Center Up Note: Terminal numbers are actually on
Pole Model the switch. Actuator positions oriented
Programmable Illuminated PB
with switch part number facing front.
JWM11 1 (COM)
SP JWMW11 ON NONE OFF 1-1b OPEN OPEN SPST
JWL11 1b
JWM12 1 (COM)
SP JWMW12 ON NONE ON 1-1b OPEN 1-1a SPDT
1a
JWL12 1b
JWM21
JWMW21 1-1b 1 (COM) 2
Keylocks
DP ON NONE OFF OPEN OPEN DPST
JWL21 2-2b 1b 2b
JWLW21
JWM22
1 (COM) 2
JWMW22 1-1b 1-1a
DP ON NONE ON OPEN DPDT
Rotaries
JWL22 2-2b 2-2a 1a 1b 2a 2b
JWLW22
Slides
R No Barrier
B With Barrier
Tactiles
JWM JWL JWM JWL
Tilt
Barrier type designates that either AT217 (for JWM) or
No-barrier type has a flat flange AT218 (for JWL) is factory assembled.
which is an integral part of the switch. Dimensions for barriers are shown in the Accessories section.
Touch
JWMW and JWLW panel seal devices have exterior seal Barrier Colors
of acrylonitrile butadiene rubber covering the flange. Available:
A Black
B Ivory
H Gray
Indicators
Flange/Housing Material: Polyamide Finish: Matte Barrier Material: Polyamide Finish: Matte
CAP COLORS
Accessories
Cap Colors
Available:
A Black
B Ivory
C Red
H Gray
Cap Material: Polyphenelene Oxide Rocker cap is an integral part of the switch and not available separately.
Supplement
Finish: Matte JWMW and JWLW available with black or red caps only.
www.nkkswitches.com B43
Series JW High Inrush 10 & 16 Amp Rockers
Toggles
INSCRIPTIONS
B
Pushbuttons
The IEC symbols for On-Off are supplied with Single Throw models only.
DPST models without inscriptions Orientation of inscription must be selected.
Programmable Illuminated PB
do not have VDE approval. Inscription Colors: Black ink on Ivory or Gray cap. White ink on Black or Red cap.
Contact factory for other inscriptions.
HOUSING
Colors
Available:
A Black
B Ivory
H Gray
Material: Polyamide
Keylocks
Finish: Matte JWMW and JWLW panel seal models available with black housing only.
TERMINALS
Rotaries
Solder Lug/Quick Connect .110 (2.8mm) Solder Lug/Quick Connect .187 (4.75mm)
(3.2)
Epoxy Seal .126 (7.5) Epoxy Seal (7.5)
.295 .295
Slides
(1.5) R
JWM & JWMW (0.6) R JWL & JWLW .059
.024 (2.8) (0.65) R
(1.6) .110 .026 (4.75)
.063 .187
Thk = (0.5) Thk = (0.8)
.020 .031
Tactiles
PANEL CUTOUTS
(29.5) (30.7)
1.161 1.209
(20.5) (20.5)
.807 .807
B44 www.nkkswitches.com
High Inrush 10 & 16 Amp Rockers Series JW
Toggles
TYPICAL SWITCH DIMENSIONS FOR JWM & JWMW
Rockers
B
(6.0) (15.0)
Part No. .591
.236
Pushbuttons
(7.7) Typ 2b 1b
(16.4) 2a 1a
Programmable Illuminated PB
.646
JWM11RC1A
Keylocks
(15.0)
Part No. .591
Rotaries
(7.7) Typ 2b 1b
.303 2 1
(19.6) (25.0) (22.6) (30.0)
.772 .984 .890 COM COM
1.181
2a 1a
Slides
(0.5) Typ
(13.6) .020 (2.8) Typ
.535 (18.0) (6.2) .110
.709 .244
(22.2) (7.2) (18.9) (7.5) (15.4)
.874 .283 .744 .295 .606
Tactiles
JWM11BCA-H
Tilt
Part No. (7.0) (15.0)
.276 .591
Touch
(7.7) Typ 2b 1b
.303 2 1
(29.6)
(19.6) (22.6)
26 .890 1.165
.772 COM COM
Indicators
(16.4) 2a 1a
.646
(0.5) Typ
.020 (2.8) Typ
.110
(13.6) (3.0) (6.2)
.244
Accessories
.535 .118
(21.0) (21.5) (7.5) (15.4)
.827 .846 .295 .606
JWMW22RCA
Supplement
Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a.
www.nkkswitches.com B45
Series JW High Inrush 10 & 16 Amp Rockers
Toggles
(9.8) Typ 2b 1b
.386 2 1
(20.2) 2a 1a
.795
Programmable Illuminated PB
JWL21RC2A Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a.
Keylocks
(9.8) Typ 2b 1b
.386 2 1
2a 1a
Slides
JWL11BCA-H Single pole double throw models do not have terminals 2a, 2, & 2b; single throw models do not have 1a & 2a.
Tilt
2b 1b
(9.8)
.386 2 1
(24.4) (28.0) (37.3)
26 1.102 1.469
.961
COM COM
(20.2)
2a 1a
.795
Accessories
(17.6) (9.0)
.693 .354
Supplement
JWLW21RA1A
B46 www.nkkswitches.com
High Inrush 10 & 16 Amp Rockers Series JW
Toggles
TYPICAL SWITCH DIMENSIONS FOR JWLW
Rockers
Part No.
(7.9)
.311
(0.8) Typ
(4.75) Typ
.187 B
.031
Pushbuttons
2b 1b
(9.8) Typ
.386 2 1
(24.4) (28.0) (37.3)
26 1.102 1.469
.961
COM COM
(20.2)
Programmable Illuminated PB
2a 1a
.795
(17.6) (9.0)
.693 .354
(27.0) (2.7) (21.3) (7.5) (20.0)
1.063 .106 .839 .295 .787
JWLW22RAA
Keylocks
AT4126
Dust Cover for JWL Rocker
When installed, the Dust Cover protects the switch from an environment containing
Rotaries
small particles and dust. The switch is operable with the Dust Cover in place.
Slides
Base: Black Polyamide Loses pliability below 0C (+32F)
Tactiles
Assembly Instructions:
Tilt
1. Insert bottom of switch through the base until
(42.0)
the tabs lock into place.
1.654
2. Snap the switch into the panel.
3. Seat the lid into the grooves of the base. Touch
Indicators
(2.6)
(22.2) (8.6)
.102
(33.0)
Groove
.874 .339 1.299
2. The dust cover cannot be used with the barrier option. Groove
www.nkkswitches.com B47
Series JW High Inrush 10 & 16 Amp Rockers
Toggles
PRECAUTIONS FOR HANDLING & STORAGE FOR JWMW/LW (PANEL SEAL TYPES)
Operating Environment
Rockers
B Do not install switch where heavy dust collection occurs. Dust build-up under rocker may affect switch actuation.
water may occur. In such an environment, a minimum 30 angle installation is advisable. If there is
a possibility of freezing, install vertically so no moisture will be retained within switch housing.
Panel Mounting
Programmable Illuminated PB
Incorrect Correct
Before snapping a switch into the panel, align the gasket evenly under bezel of the switch.
When mounting into a panel, apply equal pressure to sides of bezel and insert parallel to panel.
After mounting a switch, be sure there are no gaps between switch and panel.
Lightly push into panel.
After panel installation and wiring is completed, do not apply force horizontally
Keylocks
Behind the panel, cut area should be squared. If front of panel is painted, do not allow any paint to collect in
corners of cutout to prevent level mounting.
Avoid reinstalling a switch once it has been mounted in a panel. This may cause deterioration of panel sealability.
Rotaries
Slides
Tactiles
Tilt
Touch
Indicators
Accessories
Supplement
B48 www.nkkswitches.com