Académique Documents
Professionnel Documents
Culture Documents
Input data
Project
Date : 18/10/201
7
Settings
Standard - LRFD 2003
Materials and standards
Concrete structures ECP-2008
:
Piles
Analysis for drained conditions : NAVFAC DM 7.2
Load curve : linear (Poulos)
Horizontal bearing capacity : Elastic subsoil (p-y method)
Verification methodology : Safety factors (ASD)
Safety factors
Permanent design situation
Safety factor for compressive pile : SFcp = 2.00 []
Safety factor for tensile pile : SFtp = 3.00 []
Basic soil parameters
g n
No. Name Pattern
[pcf] []
j ef d K cu a
No. Name Pattern
[] [] [] [psf] []
Soil parameters
CLAY
Unit weight : g = 18.0 pcf
[GeoStructural Analysis - Piles | version 5.19.5.0 | Copyright 2015 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
Poisson's ratio : n = 0.20
Oedometric modulus : Eoed = 12.0 psi
Saturated unit weight : gsat = 19.0 pcf
Pile skin friction : d = 19.00
Coefficient of lateral stress : K = 1.00
SAND
Unit weight : g = 18.5 pcf
Poisson's ratio : n = 0.24
Oedometric modulus : Eoed = 10.0 psi
Saturated unit weight : gsat = 19.5 pcf
Pile skin friction : d = 18.50
Coefficient of lateral stress : K = 1.00
Geometry
Pile profile: circular
Dimensions
Diameter d = 1.70 ft
Length l = 25.00 ft
Location
Off ground height h = 3.00 ft
Depth of finished grade hz = 6.00 ft
Technology: Bored piles
1 15.00 CLAY
2 5.00 CLAY
[GeoStructural Analysis - Piles | version 5.19.5.0 | Copyright 2015 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
3 - SAND
Load
Load N Mx My Hx Hy
No. Name Type
new change [lbf] [lbfft] [lbfft] [lbf] [lbf]
1 YES Load No. 1 Design 50.00 10.0 10.0 1.00 1.00
2 YES Load No. 1 - service Service 41.67 8.3 8.3 0.83 0.83
Ground water table
The ground water table is at a depth of 6.00 ft from the original terrain.
Global settings
Analysis of vertical bearing capacity : analytical solution
Analysis type : analysis for drained conditions
Verification No. 1
Verification of pile bearing capacity according to NAVFAC DM 7.2 - partial results
Computation of pile base bearing capacity:
The soil under the base is cohesionless
Coefficient of bearing capacity Nq = 2.88
Area of pile transverse cross-section Ap = 2.27E+00 ft2
Pile ultimate skin resistance capacity:
[GeoStructural Analysis - Piles | version 5.19.5.0 | Copyright 2015 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
Safety factor = 2.0 < 2.00
Verification No. 1
Analysis of load settlement curve - input data
Layer Es
No. [psi]
1 2175.6
2 2175.6
3 2175.6
Type of pile : end-bearing pile
Maximum pile settlement slim = 1.00 in
Verification No. 1
Input data to compute pile horizontal bearing capacity
Analysis carried out for the load case number1. (Load No. 1)
Horizontal bearing capacity verified in the direction of Y.
[GeoStructural Analysis - Piles | version 5.19.5.0 | Copyright 2015 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
2.50 4.00 -0.00 0.00 0.08 -0.81 12.32
3.75 6.00 -0.00 0.00 0.10 -0.62 13.21
3.75 6.00 -0.00 0.00 0.10 -0.62 13.21
5.00 8.00 -0.00 0.00 0.12 -0.39 13.84
5.00 8.00 -0.00 0.00 0.12 -0.39 13.84
6.25 10.00 -0.00 0.00 0.12 -0.13 14.16
6.25 10.00 -0.00 0.00 0.12 -0.13 14.16
7.50 12.00 -0.00 0.00 0.12 0.12 14.16
7.50 12.00 -0.00 0.00 0.12 0.12 14.16
8.75 14.00 -0.00 0.00 0.11 0.37 13.85
8.75 14.00 -0.00 0.00 0.11 0.37 13.85
10.00 16.00 -0.00 0.00 0.10 0.59 13.24
10.00 16.00 -0.00 0.00 0.10 0.59 13.24
11.25 18.00 -0.00 0.00 0.08 0.79 12.37
11.25 18.00 -0.00 0.00 0.08 0.79 12.37
12.50 20.00 -0.00 0.00 0.07 0.95 11.28
12.50 20.00 -0.00 0.00 0.07 0.95 11.28
13.75 22.00 -0.00 0.00 0.05 1.07 10.01
13.75 22.00 -0.00 0.00 0.05 1.07 10.01
15.00 24.00 -0.00 0.00 0.03 1.15 8.61
15.00 24.00 -0.00 0.00 0.03 1.15 8.61
16.25 26.00 -0.00 0.00 0.01 1.19 7.14
16.25 26.00 -0.00 0.00 0.01 1.19 7.14
17.50 28.00 0.00 0.00 -0.02 1.17 5.66
17.50 28.00 0.00 0.00 -0.02 1.17 5.66
18.75 30.00 0.00 0.00 -0.04 1.11 4.22
18.75 30.00 0.00 0.00 -0.04 1.11 4.22
20.00 32.00 0.00 0.00 -0.06 1.00 2.90
20.00 32.00 0.00 0.00 -0.06 1.00 2.90
21.25 34.00 0.00 0.00 -0.09 0.84 1.74
21.25 34.00 0.00 0.00 -0.09 0.84 1.74
22.50 36.00 0.00 0.00 -0.12 0.62 0.82
22.50 36.00 0.00 0.00 -0.12 0.62 0.82
23.75 38.00 0.00 0.00 -0.15 0.34 0.22
23.75 38.00 0.00 0.00 -0.15 0.34 0.22
25.00 40.00 0.00 0.00 -0.17 0.00 0.00
Maximum internal force and deformation :
Pile head = 0.00 in
displacement
Max. pile displacement = 0.00 in
Max. shear force = 1.19 lbf
Maximum moment = 14.2 lbfft
Dimensioning of reinforcement:
Reinforcement - 8 pc bar No. 18; covering 2.00 in
Type of structure (reinforcement ratio) : column
[GeoStructural Analysis - Piles | version 5.19.5.0 | Copyright 2015 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
Reinforcement ratio r = 1.5 % >( 1.000 % = rmin)
Cross-section is NOT SATISFACTORY; increase reinforcement ratio.
[GeoStructural Analysis - Piles | version 5.19.5.0 | Copyright 2015 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]