Académique Documents
Professionnel Documents
Culture Documents
MODULE-40C
Connections- simple and eccentric, beamcolumn connections.
___________________________________________________________________________
Ans:
JH ACADEMY Page 1
SUB: RCC AND STEEL
MODULE-40C
2. A moment M of magnitude 50 kN-m is transmitted to a column
flange through a bracket by using four 20 mm diameter rivets as
shown in the figure.
The shear force induced in the rivet A is
Ans:
( )
(a) Lesser of the bearing strength of rivet and the shearing strength
of the rivet
(b) Lesser of the bearing strength of rivet and the tearing strength
of thinner plate
(c) Greater of the bearing strength of rivet and the shearing strength
of the rivet
(d) Lesser of the shearing strength of the rivet and the tearing
strength of thinner plate
Ans: (a)
JH ACADEMY Page 2
SUB: RCC AND STEEL
MODULE-40C
4. An unstiffened web I section is fabricated from a 10 mm thick plate
by fillet welding as shown in the figure. If yield stress of steel is
250 MPa, the maximum shear load that section can take is
Ans:
Ans:
( )
JH ACADEMY Page 3
SUB: RCC AND STEEL
MODULE-40C
Ans:
Ans:
( )
( )
( )
JH ACADEMY Page 4
SUB: RCC AND STEEL
MODULE-40C
8. A bracket connection is made with four bolts of 10 mm diameter
and supports a load of 10 kN at an eccentricity of 100 mm. The
maximum force to be resisted by any bolt will be
Ans:
( )
Ans: (a)
10. A 12mm thick plate is connected to two 8mm plates, on either side
through a 16mm diameter power driven field rivet as shown in the
figure below. Assuming permissible shear stress as 90MPa and
permissible bearing stress as 270MPa in the rivet, the rivet value of
the joint is
Ans:
JH ACADEMY Page 5
SUB: RCC AND STEEL
MODULE-40C
11. A double cover butt riveted joint is used to connect two flat plates
of 200 mm width and 14 mm thickness as shown in the figure.
There are twelve power driven rivets of 20 mm diameter at a pitch
of 50 mm in both directions on either side of the plate. Two cover
plates of 10 mm thickness are used. The capacity of the joint in
tension considering bearing and shear ONLY, with permissible
bearing and shear stresses as 300 MPa and 100 MPa respectively is
Ans:
Ans:
JH ACADEMY Page 6
SUB: RCC AND STEEL
MODULE-40C
13. For the fillet weld of size's' shown in the figure the effective throat
thickness is
Ans: (B)
14. In a steel plate with bolted connections, the rupture of the net
section is a mode of failure under
Ans: (A)
Ans:
JH ACADEMY Page 7
SUB: RCC AND STEEL
MODULE-40C
16. What is the strength of 20 mm diameter bolt (KN) of
in lap joint of 12 mm thick plates. Assume pitch =50 mm,
edge distance = 33 mm, net tensile stress area of bolt = 245
and ultimate stress of plate is 410 MPa.
a) 45.26 b) 96 c) 90.52 d) 48
Ans:
( )
( )
( )
( )
a) 45.26 b) 80 c) 90.52 d) 40
Ans:
( )
( )
( )
( )
( )
( )
JH ACADEMY Page 8
SUB: RCC AND STEEL
MODULE-40C
a) 45.26 b) 96 c) 90.52 d) 48
Ans:
( )
( )
( )
( )
( )
19. A double cover butt bolted joint is used to connect two flat plates
of 190 mm width and 12 mm thickness as shown in the figure.
There are four bolts of 16 mm diameter ( )at a
pitch of 65 mm in both directions on either side of the plate and
edge distance of 35 mm. Two cover plates of 6 mm thickness are
used. The capacity (KN) of the joint in tension considering bearing
and shear ONLY, with for plates and
for bolts.
( )
( )
( )
( )
JH ACADEMY Page 9
SUB: RCC AND STEEL
MODULE-40C
20. A 10 mm gusset plate is connected with 150x12 mm flat by three
numbers of 20 mm diameter bolts. ( )at a pitch of
65 mm and edge distance of 40 mm.. The capacity (KN) of the
joint in tension considering bearing and shear ONLY, with
for plates and for bolts.
( )
( )
( )
( )
Ans:
( )
( )
( )
( )
JH ACADEMY Page 10