Académique Documents
Professionnel Documents
Culture Documents
Technical
Information
Load Sensing Steering Units, Priority Valves and Flow Amplifiers
Technical Information
A Wide Range of Steering Components
F500 026
Frontpage: F300 611, F300 612, F300 615, F300 617, F300 620, F300 622, F301 256, F301 470, F300 601. Drawing 151-577
Conversion
Conversion Factors
Factors 1 Nm = [8.851 lbfin] 1 cm3 = [0.061 in3]
1N = [0.2248 lbf ] 1l = [0.264 US gal]
1 bar = [14.50 psi] F = [1.8C + 32]
1 mm = [0.0394 in]
T301035
Survey of Literature Detailed data on all Sauer-Danfoss steering components and accessories can be found in
with Technical Data on our steering component catalogues, which is divided in to 6 individual sub catalogues:
Sauer-Danfoss Steering
Components
General information Steering components
Technical data on load sensing steering OSPB, OSPC, OSPF, OSPD, OSPQ,
units, priority valves and flow amplifiers OSPL, OSPBX, OSPLX, OVPL, OLS and
OSQ
Technical data on hydraulic and electro- EHPS, EHPS w. OLS 320, PVE for
hydraulic pilot operated steering valves, EHPS and OSPCX
electrical actuation modules and
appropriate steering units.
Reaction
With reaction steering units any external forces acting on the steered wheels result in
a corresponding movement of the steering wheel when the driver is not steering the
vehicle.
Non-reaction
With non-reaction steering units there is no corresponding movement of the steering
wheel when the driver is not steering the vehicle
P LS T
L R
CETOP F300614
diagram
OSPB LS (OLS)
Versions
F300614 F300724
OSPC LS: Steering unit load sensing OSPC LS: Steering unit load sensing
with integrated valve functions for in with integrated valve functions for
line priority valve OLS flange on priority valve OLSA
L R
LS
L P T LS R
P T
L R
LS
L P T LS R
P T
150-596.10
150-595.11
Versions
F300617
OSPC LSR: Steering unit load sensing OSPF LS : Steering unit full drain load
dynamic with integrated valve sensing dynamic and with integrated
functions valve functions
L R L R
LS
P LS T P T
L R L R
P T LS P T LS
150-598.11 150-597.11
Version OSPD LS: Steering unit load sensing OSPQ LS: Steering unit load sensing
dynamic with 2 rotary meters and with dynamic with flow amplification and
integrated valve functions with integrated valve functions
The OSPD has 2 rotary meters (gear The OSPQ has incorporated amplification
wheel sets). Should the pump supply be valve. Should pump supply fail or the
lost, only one rotary meter is active for steering wheel speed be less than
emergency steering. In normal steering approximate 10 rev/min only the rotary
situations both rotary meters are active. meter determines the displacement. In
normal steering situations or at higher
steering wheel speed, oil is also led to
the steering cylinder via the built in
amplification valve.
F300612 F300615
L R
L R
LS
P T
P LS T
L R
L R
P T LS
P T LS
150-599.11
150-600.11
OSPD LS (OLS) OSPQ LS (OLS)
Load sensing dynamic non-reaction Load sensing dynamic non-reaction
F300611
L R L R
OSPL LS (OLS) OSPL LS (OLS)
Load sensing static Load sensing dynamic
non-reaction non-reaction LS
P LS T P T
L R L R
LS
P T
P T LS
150-601.10
150-301.11
L R
L R
F301 082
P T LS
150-613.10
Versions OSPBX LS, OSPCX LS and OSPLX LS: Steering units load sensing for flow amplifiers.
OSPBX LS, OSPCX LS and OSPX LS are load sensing steering units with the L and the R
connections open to tank when in neutral position. OSPBX LS, OSPCX LS and OSPX LS
can only be used with Sauer-Danfoss flow-amplifiers OSQA or OSQB. OSPBX LS, OSPCX
LS and OSPX LS steering units must not be connected directly to the steering cylinder.
OSPCX LS is for OSQ dynamic without pilot pressure relief valve.
F300614
L R
L R
LS
P LS T
P T
L R
L R
LS
P T LS P T
150-310.12
150-602.10
Code Numbers and OSPB load sensing static non-reaction steering units
Weights OSPB LS Static steering units have no valve functions.
OSPB LS in the table below have all standard neutral setting springs, see page 24
Code Numbers
Connections Weight
Steering unit European version for OLS US version for OLS
G 1/2 3/4-16 UNF - O* kg [lb]
G 1/4 - S** 7/16-20 UNF - O* + S**
OSPB 50 LS - 150G6085 5.2 [11.46]
OSPB 80 LS - 150G6086 5.3 [11.68]
OSPB 100 LS - 150G6087 5.4 [11.90]
OSPB 125 LS - 150G6088 5.5 [12.13]
OSPB 160 LS - 150G6089 5.6 [12.35]
OSPB 200 LS 150-0103 150G6090 5.8 [12.79]
OSPB 315 LS 150-0104 150-0116 6.2 [13.67]
OSPB 400 LS 150-0105 150-0117 7.0 [15.43]
Code Numbers and OSPB load sensing dynamic non-reaction steering units
Weights OSPB LS Dynamic steering units have no valve functions.
OSPB LS in the table below have all standard neutral setting springs, see page 24
Code Numbers
Connections Weight
Steering unit US version for OLS
3/4-16 UNF - O* kg [lb]
7/16-20 UNF - O* + S**
OSPB 50 LS 150-8204 5.2 [11.46]
OSPB 80 LS 150-8205 5.3 [11.68]
OSPB 100 LS 150-8206 5.4 [11.90]
OSPB 125 LS 150-8207 5.5 [12.13]
OSPB 160 LS 150-8208 5.6 [12.35]
OSPB 200 LS 150-8209 5.8 [12.79]
OSPB 315 LS 150-8210 6.2 [13.67]
OSPB 400 LS 150-8211 7.0 [15.43]
Code Numbers and OSPC load sensing static non-reaction steering unit
Weights OSPC LS Static steering units in the table below incorporate all the following valve
functions:
check valve in P-port
pilot pressure relief valve
shock valves
suction valves
OSPC LS in the table below have all standard neutral setting springs, see page 24
If you require other port connections, valve combinations and/or other valve settings
or other displacements, please fill in the order form on page 24 and contact the Sauer-
Danfoss Sales Organization.
Code Numbers and OSPC load sensing dynamic non-reaction steering units
Weights OSPC LS Dynamic steering units in the table below incorporate all the following valve
functions:
check valve in P-port
pilot pressure relief valve
shock valves
suction valves
check valve in LS-line for all OSPC LS Dynamic up to and including 200 cm3/rev
OSPC LS in the table below have all standard neutral setting springs, see page 24
If you require other port connections, valve combinations and/or other valve settings
or other displacements please fill in the order form on page 24 and contact the Sauer-
Danfoss Sales Organization.
Code Numbers and OSPC load sensing dynamic reaction steering units
Weights OSPC LSR Dynamic steering units in the table below incorporate all the following valve
functions:
check valve in P-port
pilot pressure relief valve
shock valves
suction valves
check valve in LS-line
OSPC LSR in the table below have all standard neutral setting springs, see page 24
If you require other port connections, valve combinations, valve settings and/or other
displacements, please fill in the order form on page 24 and contact the Sauer-Danfoss
Sales Organization.
Code Numbers and OSPF load sensing dynamic non-reaction steering units
Weights OSPF LS Dynamic steering units in the table below incorporate all the following valve
functions:
check valve in P-port
pilot pressure relief valve
shock valves
suction valves
OSPF LS in the table below have all soft neutral setting springs, see page 24
If you require other port connections, valve combinations, valve settings and/or other
displacements, please fill in the order form on page 24 and contact the Sauer-Danfoss
Sales Organization.
S**: Spot face around port connections (can not be used in connection with OVR angular block)
If you require other port connections, valve combinations, valve settings and/or other
displacements, please fill in the order form on page 24 and contact the Sauer-Danfoss
Sales Organization.
Code Numbers and OSPQ load sensing dynamic non-reaction steering units
Weights OSPQ LS Dynamic steering units in the table below incorporate all the following valve
functions:
check valve in amplification valve, act as check valve in P-port
pilot pressure relief valve
shock valves
suction valves
check valve in LS-line
OSPQ LS in the table below have all standard neutral setting springs, see page 24
If you require other valve combinations, valve settings and/or other displacements,
please fill in the order form on page 24 and contact the Sauer-Danfoss Sales
Organization.
Code Numbers and OSPL load sensing static non-reaction steering units
Weights OSPL LS Static steering units have no valve functions.
OSPL LS in the three tables below have all strong neutral setting springs, see page24
Code numbers
Connections
US version for US version for Weight
Steering unit European version
OLS OLS and OVPL LS
for OLS kg [lb]
3/4-16 UNF - O* - port
G 1/2
7/16-20 UNF - O* 7/16-20 UNF - O*
G 1/4 - S**
+ S** + S**
OSPL 520 LS 150-7169 150-7167 150-7168 8.1 [17.86]
OSPL 630 LS 150-7107 150-7164 150-7113 8.4 [18.52]
OSPL 800 LS 150-7108 150-7165 150-7114 8.8 [19.40]
OSPL 1000 LS 150-7110 150-7166 150-7115 10.0 [22.05]
O*: O-ring chamfer on port connections S**: Spot face around port connection
O*: O-ring chamfer on port connections S**: Spot face around port connection
OSPL LS Dynamic steering units in the table below incorporate all the following valve
function: pilot pressure relief valve
If you require other displacements or other valve setting, please fill in the order form on
page 24 and contact the Sauer-Danfoss Sales Organization.
Code Numbers and OSPL 1200 LS Dynamic steering unit in the table below incorporate all the following
Weights valve function:
shock valves
suction valves
OSPL 1200 LS in the table below has strong neutral setting springs, see page 24
If you require other displacements or other valve setting, please fill in the order form on
page 24 and contact the Sauer-Danfoss Sales Organization.
Code Numbers and OSPBX and OSPLX load sensing static steering units for OSQ static
Weights OSPBX LS and OSPLX LS Static steering units in the table below have no valve functions.
OSPBX LS in the table below have all standard neutral setting springs, see page 24
OSPLX LS in the table below have all strong neutral setting springs, see page 24
Code numbers
Connections Weight
Steering unit European version US version
G 1/2 3/4-16 UNF - O* kg [lb]
G 1/4 - S** 7/16-20 UNF - O* + S**
OSPBX 160 LS 150-1082 150-1078 5.6 [12.35]
OSPBX 200 LS 150-1083 150-1079 5.8 [12.79]
OSPBX 315 LS 150-1084 150-1080 6.2 [13.67]
OSPBX 400 LS 150-1085 150-1081 7.0 [15.43]
OSPLX 520 LS 150-7170 150-7173 8.1 [17.86]
OSPLX 630 LS 150-7171 150-7174 8.4 [18.52]
OSPLX 800 LS 150-7172 150-7155 8.8 [19.40]
If you require other displacements or other valve setting, please fill in the order form on
page 24 and contact the Sauer-Danfoss Sales Organization.
Specification Table for Fill in your company data and place xs in the table where appropriate, then send to your
Non Catalogue Numbers Sauer-Danfoss Sales Organisation.
of LS Steering Units
An alternative way to specify a variant is to state an existing code number and add the
modifications, you would like to have implemented in the basic steering unit.
Requested modifications:
Port Thread Versions and The following combinations of port threads and valves are available for OSPC LS/LSR:
Valve Combinations Housings for low flow: 40 - 200 cm3/rev [2.44 - 12.20 in3/rev] gear wheel set.
Threads Valves
For Pilot Check valve in
Main ports Shock Suction
LS-port steering pressure LS (only for LS
(P, T, L, R) valves valves
column relief valve Dynamic)
DIN 3852-2 DIN 3852-2 Yes Yes Yes Yes
M10 x 1.5
G 1/2 G 1/4 w. spot face Yes Yes Yes No
DIN 3852-2 DIN 3852-2 Yes Yes Yes Yes
M10 x 1.5
G 1/2 w. spot face G 1/4 w. spot face Yes Yes Yes No
ISO 6149-1 ISO 6149-1
Yes Yes Yes Yes
M18 x 1.5, M12 x 1.5,
M10 x 1.5
w. O-ring chamfer w. O-ring chamfer
Yes Yes Yes No
and spot face and spot face
ISO 11926-1
ISO 11926-1 Yes Yes Yes Yes
7/16 - 20 UNF
3/4 - 16 UNF, 3/8 - 16 UNC
O-ring boss port
O-ring boss port Yes No No No
and spot face
ISO 11926-1
ISO 11926-1
7/16 - 20 UNF
3/4 - 16 UNF, M10 x 1.5 Yes Yes Yes Yes
O-ring boss port
O-ring boss port
and spot face
Yes Yes Yes Yes
For OLSA For OLSA M10 x 1.5 Yes Yes Yes No
Yes No No No
The following combinations of port threads and valves are available for OSPC LS/LSR:
Housings for high flow: 250 - 400 cm3/rev [15.25 -24.4 in3/rev] gear wheel set.
Threads Valves
For Pilot Check valve in
Main ports Shock Suction
LS-port steering pressure LS (only for LS
(P, T, L, R) valves valves
column relief valve Dynamic)
DIN 3852-2 DIN 3852-2 Yes Yes Yes No
M10 x 1.5
G1/2 G 1/4 w. spot face No Yes Yes No
DIN 3852-2 DIN 3852-2 Yes Yes Yes No
M10 x 1.5
G 1/2 w. spot face G 1/4 w. spot face Yes No No Yes
ISO 11926-1 Yes Yes Yes No
ISO 11926-1
7/16 - 20 UNF Yes No No No
3/4 - 16 UNF, 3/8 - 16 UNC
O-ring boss port No Yes Yes No
O-ring boss port
and spot face No Yes No No
ISO 11926-1
ISO 11926-1 Yes Yes Yes No
7/16 - 20 UNF
3/4 - 16 UNF, M10 x 1.5
O-ring boss port
O-ring boss port Yes No No No
and spot face
For OLSA For OLSA M10 x 1.5 Yes Yes Yes No
Housings with spot face around port connections on main ports cannot be used in
connection with OVR angular block.
Port Thread Versions and The following combinations of port threads and valves are available for OSPF LS:
Valve Combinations Threads Valves
(continued) Main ports
For Pilot
Shock
LS-port steering pressure Suction valves
(P, T, L, R) valves
column relief valve
DIN 3852-2 DIN 3852-2
M10 x 1.5 Yes Yes Yes
G 1/2 G 1/4 w. spot face
DIN 3852-2 DIN 3852-2
M10 x 1.5 Yes Yes Yes
G 1/2 w. spot face G 1/4 w. spot face
ISO 6149-1 ISO 6149-1
Yes Yes Yes
M18 x 1.5, M12 x 1.5,
M10 x 1.5
w. O-ring chamfer w. O-ring chamfer
No Yes Yes
and spot face and spot face
ISO 11926-1
ISO 11926-1
7/16 - 20 UNF
3/4 - 16 UNF, 3/8-16 UNC Yes Yes Yes
O-ring boss port
O-ring boss port
and spot face
ISO 11926-1
ISO 11926-1
7/16 - 20 UNF
3/4 - 16 UNF, M10 x 1.5 Yes Yes Yes
O-ring boss port
O-ring boss port
and spot face
The following combinations of port threads and valves are available for OSPD LS/LSR:
Threads Valves
For Pilot Check valve in
Main ports Shock Suction
LS-port steering pressure LS (only for LS
(P, T, L, R) valves valves
column relief valve Dynamic)
DIN 3852-2 G w. DIN 3852-2 G w.
M10 x 1.5 Yes Yes Yes Yes
spot face spot face
ISO 6149-1 ISO 6149-1
M18 x 1.5, M12 x 1.5,
M10 x 1.5 Yes Yes Yes Yes
w. O-ring chamfer w. O-ring chamfer
and spot face and spot face
ISO 11926-1
ISO 11926-1 Yes Yes Yes Yes
7/16 - 20 UNF
- 16 UNF, M10 x 1.5
O-ring boss port
O-ring boss port Yes Yes Yes No
and spot face
Port Thread Versions and The following combinations of port threads and valves are available for OSPQ LS/LSR:
Valve Combination Threads Valves
(continued) Main ports
For Pilot
Shock Suction
Check valve in
LS-port steering pressure LS (only for LS
(P, T, L, R) valves valves
column relief valve Dynamic)
ISO 6149-1 ISO 6149-1
Yes Yes Yes Yes
M18 x 1.5, M12 x 1.5,
M10 x 1.5
w. O-ring chamfer w. O-ring chamfer
No Yes Yes Yes
and spot face and spot face
Housings with spot face around port connections on main ports cannot be used in
connection with OVR angular block.
For OSPL, OSPBX, OSPCX and OSPLX only the versions listed in the tables with code
numbers are available.
Technical Data Displacement, flow and pressure: OSPB LS, OSPC LS, OSPC LSR
Common data: Look in sub catalogue: General Steering Components
Displacement *Rated oil flow Max. pressure on connections
Steering unit cm3/rev l/min
P bar [psi] T bar [psi] L. R bar [psi]
[in3/rev] [US gal/min]
OSPC 40 LS Static 40 [2.44] 4 [1.06]
OSPB/OSPC 50 LS Static 50 [3.05] 5 [1.32] 140 [2030]
OSPC 60 LS Static 60 [3.66] 6 [1.58]
OSPC 70 LS Static 70 [4.27] 7 [1.85]
OSPB/OSPC 80 LS Static 80 [4.88] 8 [2.11]
175 [2538]
OSPB/OSPC 100 LS Static 100 [6.10] 10 [2.64]
OSPB/OSPC 125 LS Static 125 [7.63] 13 [3.43]
40 [580] 280 [4061]
OSPB/OSPC 160 LS Static 160 [9.76] 16 [4.23]
OSPC 185 LS Static 185 [11.29] 19 [5.02]
OSPB/OSPC 200 LS Static 200 [12.20] 20 [5.28]
OSPC 230 LS Static 230 [14.03] 23 [6.07] 175 [2538]
OSPC 250 LS Static 250 [15.25] 25 [6.60]
OSPB/OSPC 315 LS Static 315 [19.22] 32 [8.45]
OSPB/OSPC 400 LS Static 400 [24.41] 40 [10.57]
OSPC 40 LS Dynamic 40 [2.44] 4 [1.06]
OSPB/OSPC 50 LS Dynamic 50 [3.05] 5 [1.32] 140 [2030]
OSPC 60 LS Dynamic 60 [3.66] 6 [1.58]
OSPC 70 LS Dynamic 70 [4.27] 7 [1.85]
OSPB/OSPC 80 LS Dynamic 80 [4.88] 8 [2.11] 175 [2538]
OSPB/OSPC 100 LS Dynamic 100 [6.10] 10 [2.64]
OSPB/OSPC 125 LS Dynamic 125 [7.63] 13 [3.43]
40 [580] 280 [4061]
OSPB/OSPC 160 LS Dynamic 160 [9.76] 16 [4.23]
OSPC 185 LS Dynamic 185 [11.29] 19 [5.02]
OSPB/OSPC 200 LS Dynamic 200 [12.20] 20 [5.28]
210 [3045]
OSPC 230 LS Dynamic 230 [14.03] 23 [6.07]
OSPC 250 LS Dynamic 250 [15.25] 25 [6.60]
OSPB/OSPC 315 LS Dynamic 315 [19.22] 32 [8.45]
OSPB/OSPC 400 LS Dynamic 400 [24.41] 40 [10.57]
OSPC 40 LSR Dynamic 40 [2.44] 4 [1.06]
OSPC 50 LSR Dynamic 50 [3.05] 5 [1.32] 140 [2030]
OSPC 60 LSR Dynamic 60 [3.66] 6 [1.58]
OSPC 70 LSR Dynamic 70 [4.27] 7 [1.85]
OSPC 80 LSR Dynamic 80 [4.88] 8 [2.11] 175 [2538]
40 [580] 280 [4061]
SPC 100 LSR Dynamic 100 [6.10] 10 [2.64]
OSPC 125 LSR Dynamic 125 [7.63] 13 [3.43]
OSPC 160 LSR Dynamic 160 [9.76] 16 [4.23]
210 [3045]
OSPC 185 LSR Dynamic 185 [11.29] 19 [5.02]
OSPC 200 LSR Dynamic 200 [12.20] 20 [5.28]
*Rated flow at 100 rpm
Technical Data
Displacement, Flow and Pressure: OSPD LS, OSPQ LS
OSPD and OSPQ steering units in the table below are all Load Sensing Dynamic type.
Common data: Look in sub catalogue: General Steering Components
Displacement Displacement Rated Max. pressure on connections
manual steer *normal steer oil flow**
Steering unit
mode mode l/min P bar [psi] T bar [psi] L. R bar [psi]
cm3/rev [in3/rev] cm3/rev [in3/rev] [US gal/min]
OSPD 60/185 LS 60 [3.66] 185 [11.29] 19 [5.02]
OSPD 60/220 LS 60 [3.66] 220 [13.42] 22 [5.81]
OSPD 60/260 LS 60 [3.66] 260 [15.87] 26 [6.87]
OSPD 70/195 LS 70 [4.27] 195 [11.90] 20 [5.28]
OSPD 70/230 LS 70 [4.27] 230 [14.03] 23 [6.07]
OSPD 70/270 LS 70 [4.27] 270 [16.48] 27 [7.13]
OSPD 70/385 LS 70 [4.27] 385 [23.49] 39 [10.30] 210 [3045] 40 [580] 280 [4061]
OSPD 100/200 LS 100 [6.10] 200 [12.20] 20 [5.28]
OSPD 100/260 LS 100 [6.10] 260 [15.87] 26 [6.87]
OSPD 100/300 LS 100 [6.10] 300 [18.31] 30 [7.93]
OSPD 125/285 LS 125 [7.63] 285 [17.39] 29 [7.66]
OSPD 125/325 LS 125 [7.63] 325 [19.83] 33 [8.72]
OSPD 125/440 LS 125 [7.63] 440 [26.85] 44 [11.62]
SPD 60/185 LSR 60 [3.66] 185 [11.29] 19 [5.02]
OSPD 60/220 LSR 60 [3.66] 220 [13.42] 22 [5.81]
210 [3045] 40 [580] 280 [4061]
OSPD 70/195 LSR 70 [4.27] 195 [11.90] 20 [5.28]
OSPD 100/200 LSR 100 [6.10] 200 [12.20] 20 [5.28]
OSPQ 80/125 LS 80 [4.88] 125 [7.63] 13 [3.43]
OSPQ 80/140 LS 80 [4.88] 140 [8.54] 14 [3.70]
OSPQ 80/160 LS 80 [4.88] 160 [9.76] 16 [4.23]
OSPQ 100/160 LS 100 [6.10] 160 [9.76] 16 [4.23]
OSPQ 100/180 LS 100 [6.10] 180 [10.98] 18 [4.75]
210 [3045] 40 [580] 280 [4061]
OSPQ 100/200 LS 100 [6.10] 200 [12.20] 20 [5.28]
OSPQ 125/200 LS 125 [7.63] 200 [12.20] 20 [5.28]
OSPQ 125/250 LS 125 [7.63] 250 [15.25] 25 [6.60]
OSPQ 160/250 LS 160 [9.76] 250 [15.25] 25 [6.60]
OSPQ 160/320 LS 160 [9.76] 320 [19.53] 32 [8.45]
OSPQ 80/125 LSR 80 [4.88] 125 [7.63] 13 [3.43]
OSPQ 80/140 LSR 80 [4.88] 140 [8.54] 14 [3.70]
OSPQ 80/160 LSR 80 [4.88] 160 [9.76] 16 [4.23]
OSPQ 100/160 LSR 100 [6.10] 160 [9.76] 16 [4.23] 210 [3045] 40 [580] 280 [4061]
OSPQ 100/180 LSR 100 [6.10] 180 [10.98] 18 [4.75]
OSPQ 100/200 LSR 100 [6.10] 200 [12.20] 20 [5.28]
OSPQ 125/200 LSR 125 [7.63] 200 [12.20] 20 [5.28]
* normal steer mode: OSPQ: at a steering wheel speed higher than approximately 20 rpm, the amplification is fully active, and the displacements
in the table are valid.
** Rated flow at 100 rpm
Technical Data Displacement, flow and pressure: OSPL LS, OSPBX LS, OSPCX LS, OSPLX LS
Common data: Look in sub catalogue: General Steering Components
Displacement *Rated oil flow Max. pressure on connections
Steering unit cm3/rev l/min
P bar [psi] T bar [psi] L. R bar [psi]
[in3/rev] [US gal/min]
OSPL 520 LS Static 520 [31.73] 52 [13.74]
OSPL 630 LS Static 630 [38.44] 63 [16.64]
210 [3045] 40 [580] 280 [4061]
OSPL 800 LS Static 800 [48.82] 70** [18.49]
OSPL 1000 LS Static 1000 [61.02] 70** [18.49]
OSPL 520 LS Dynamic 520 [31.73] 52 [13.74]
OSPL 630 LS Dynamic 630 [38.44] 63 [16.64]
OSPL 800 LS Dynamic 800 [48.82] 70** [18.49] 240 [3081] 40 [580] 280 [4061]
OSPL 1000 LS Dynamic 1000 [61.02] 70** [18.49]
OSPL 1200 Dynamic 1200 [73.22] 70** [18.49]
OSPBX 160 LS Static 160 [9.76] 16 [4.23]
OSPBX 200 LS Static 200 [12.20] 20 [5.28]
OSPBX 250 LS Static 250 [15.25] 25 [6.60] 210 [3045] 40 [580] 280 [4061]
OSPBX 315 LS Static 315 [19.22] 32 [8.45]
OSPBX 400 LS Static 400 [24.41] 40 [10.57]
OSPCX 160 LS Dynamic 160 [9.76] 16 [4.23]
OSPCX 200 LS Dynamic 200 [12.20] 20 [5.28]
OSPCX 250 LS Dynamic 250 [15.25] 25 [6.60] 210 [3045] 40 [580] 280 [4061]
OSPCX 315 LS Dynamic 315 [19.22] 32 [8.45]
OSPCX 400 LS Dynamic 400 [24.41] 40 [10.57]
OSPLX 520 LS Static 520 [31.73] 52 [13.74]
OSPLX 630 LS Static 630 [38.44] 63 [16.64] 210 [3045] 40 [580] 280 [4061]
OSPLX 800 LS Static 630 [38.44] 70** [18.49]
Technical Data Valve functions in OSPC, OSPF, OSPD, OSPQ and OSPL LS steering units
Pilot pressure relief valve; (P - T, Qp) characteristic
The pilot pressure relief valve protects the steering unit against excessive pressure.
The pilot pressure relief valve in the OSPC LS, OSPF LS, OSPD LS, OSPQ LS and OSPL LS
steering unit together with the priority valve limit the maximum steering pressure P-T.
The pilot pressure relief valve is set at an oil flow to the priority valve of 25 l/min
[6.60 US gal/min].
For OSPC, OSPD, OSPQ and OSPL load sensing dynamic steering units, the setting values
are valid at a dynamic flow of 0.6 l/min [0.16 US gal/min].
For OSPF load sensing dynamic steering units, the setting values are valid at a dynamic
flow of 1.1 l/min [0.29 US gal/min].
Setting tolerance:
</= 170 bar: rated value +5 bar [72.5 psi].
> 170 bar: rated value +10 bar [145 psi].
P-T P-T
psi bar
3000
200
2500
180 A
160
B
2000 140
120
1500
100
80
1000
A = 170 + 5 bar [2465+ 73 psi] 60
OSPC/OSPF/OSPD/OSPQ/OSPL LS+OLS 80
-0 -0 0 0 Qp
+ 5 0 10 20 30 40 50 60 70 80 l/min
B = 140 bar [2030 + 73 psi]
-0 -0 Qp
0 2 4 6 8 10 12 14 16 18 20 US gal/min
152B79.10
Shock valves
The shock valves protect the steering unit and reduce external forces on the steering
cylinder by limiting the pressure difference from L to T and from R to T.
The shock valves are set at 3 l/min [0.792 US gal/min]
At higher flow pressure peaks may occur.
The shock valves are of the direct acting type, so they react very quickly.
Setting tolerance: rated value +20 bar [290 psi].
T-R T-R
T-L T-L
psi bar
100 7
6
80
5
60 4
3
40
2
20
1
0 0 Qp
0 1 2 3 4 5 6 7 8 9 10 11 l/min
Qp
0 0.25 0.50 0.75 1 1.25 1.50 1.75 2 2.25 2.50 2.75 US gal/min
150-374.10
Check valves
The check valve in the P connection of the steering unit protects the driver against
steering wheel jerks. The check valve prevents oil from flowing backwards into the pump
line when steering against a high pressure on the cylinder side. The pressure drop across
the check valve is indicated on the following graph, which assumes the use of port
adaptors with 11 mm [0.43 in] minimum bore.
p p
psi bar
90
6
75
5
60 4
45 3
30 2
15 1
0 0 Qp
0 10 20 30 40 50 60 70 80 l/min
Qp
0 3 6 9 12 15 18 21 US gal/min
150-375.11
The check valve in the LS line of OSPC LS, OSPD LS and OSPQ LS dynamic steering units
also protects the driver against steering wheel jerks. The check valve prevents oil from
flowing backwards into the LS line to the priority valve when steering against a high
pressure on the cylinder side.
In OSPF LS oil cannot flow backwards into the LS line, look in sub catalogue: General
Steering Components page 26.
OSPF LS, K L M
min. 12 [0.47]
min. 12 [0.47]
min. 15 [0.59]
OSPD LS/LSR,
OSPQ LS/LSR,
1 [0.04]
OSPL LS,
OSPBX LS,
OSPCX LS,
OSPLX LS A: G port w. spot face B: G port w. spot face C: G ports (P, T, L, R)
(LS in OSPB and OSPL (LS in OSPC/F/D/Q M: DIN 3852-2 - G
with no valves) and OSPL with valves)
K: DIN 3852-2 - G L: DIN 3852-2 - G
D E F
min. 26 [1.02]
min. 22 [0.87]
0.6 [0.024]
min. 11.5 [0.453]
min. 15 [0.59]
min. 15 [0.59]
1 [0.04]
G H I
min. 21 [0.83] min. 21 [0.83]
20.8 [0.819]
30 30
Q R S
min. 11.5 [0.453]
min. 15 [0.59]
150-603.10
G: UNF port w. O-ring chamfer H: UNF ports w. O-ring I: UNF ports w. O-ring
(LS in OSPB chamfer (LS in OSPC/ chamfer (P, T, L, R)
and OSPL with F/D and OSPL S: ISO 11926-1 - -16UNF
no valves) with valves) O-ring boss port
Q: ISO 11926-1 - 7/16-20UNF R: ISO 11926-1 - 7/16-20 UNF
O-ring boss port O-ring boss port
mm mm
Type L1 [in] L2 [in] B LS
A
126 6.5
OSPB 50
[4.96] [0.26]
44 [1.73]
47 [1.85]
129 10.4
OSPB 80
[5.08] [0.41] 82
44.4 [1.748]
25.4 [1.000]
max. 87 [3.42]
L R 81 .3 [3.2
91 [3.58]
44 [1.73]
132 13.0 .7 [ 4
3.2 0]
OSPB 100 17]
[5.20] [0.51] T P
135 16.2
OSPB 125
[5.31] [0.64]
OSPB/ 140 20.8
OSPBX 160 [5.51] [0.82] 2.8 [0.110]
OSPB/ 145 26.0 min. 7.1 [0.280] L2
45
OSPBX 200 [5.71] [1.02] 57 [2.24]
7 [0.28]
OSPB/ 151 32.5
29 [1.14] 44 [1.73] 85 [3.35]
OSPBX 250 [5.94] [1.28]
OSPB/ 160 40.9 102 [4.02]
L1
OSPBX 315 [6.30] [1.61]
OSPB/ 171 52.0
OSPBX 400 [6.73] [2.05]
LS
European version:
A: G ; 15 mm [0.59 in] deep
66 [2.60]
B: M10 1.5,
16 mm [0.63 in] deep
LS: G with spot face, 11 mm
[0.43 in] deep
64 [2.52]
US version:
A: - 16 UNF O-ring boss;
15 mm [0.59 in] deep
B: 3/8 - 16 UNC,
16 mm [0.63 in] deep
150-590.11
LS: G 7/16 - 20 UNF O-ring boss,
11.5 mm [0.45 in] deep
Dimensions OSPC LS/LSR and OSPF LS for OLS, OSPCX LS for OSQ
mm mm A B LS
Type L1 [in] L2 [in]
126 6.5
OSPC 40
47 [1.85]
[4.96] [0.26]
38 [1.50]
126 6.5 8
44.4 [1.748]
25.4 [1.000]
max. 87 [3.42]
OSPC/OSPF 50 L R 812.3 [3
91 [3.58]
44 [1.73]
[4.96] [0.26] .7 [ .240
3.2 ]
17]
128 9.1 T P
OSPC/OSPF 60
[5.04] [0.36]
128 9.1
OSPC/OSPF 70
[5.04] [0.36]
129 10.4 2.8 [0.110]
OSPC/OSPF 80
[5.08] [0.41] min. 7.1 [0.280] L2
45
132 13.0 57 [2.24]
OSPC/OSPF 100 7 [0.28]
[5.20] [0.51]
29 [1.14] 44 [1.73] 85 [3.35]
135 16.2
OSPC/OSPF 125
[5.31] [0.64] L1 102 [4.02]
OSPC LS/LSR
European version: for OLSA
A: G or G w. spot face L R LS
or M18 x 1.5 ISO 6149, T P
15 mm [0.59 in] deep
B: M10 x 1.5, 16 mm [0.63 in]
deep
LS: G w. spot face
150-591.11
or M12 x 1.5 ISO 6149,
11.5 mm [0.45 in] deep
US version:
A: -16 UNF O-ring boss,
15 mm (0.59 in) deep
B: 3/8 - 16 UNC or M10 x 1.5,
16 mm
[0.63 in] deep
LS: 7/16 - 20 UNF O-ring boss,
11.5 mm [0.45 in] deep
mm mm mm
Type L1 [in] L2 [in] L3 [in] A B LS
OSPD 195 9.1 20.8
60/185 [7.70] [0.36] [0.82]
47 [1.85]
OSPD 200 9.1 26.0
38 [1.50]
8
60/220 [7.87] [0.36] [1.02]
44.4 [1.748]
25.4 [1.000]
max. 87 [3.42]
L R 812.3 [3
91 [3.58]
.7 [ .240
44 [1.73]
OSPD 190 9.1 16.2 3.2 ]
17]
70/195 [7.48] [0.36] [0.65] T P
OSPD 195 9.1 20.8
70/230 [7.70] [0.36] [0.82]
OSPD 200 9.1 26.0
2.8 [0.110] L3
70/270 [7.87] [0.36] [1.02] 45
OSPD 215 9.1 40.9 min. 7.1 [0.280] L2 57 [2.24]
European version:
A: G w. spot-face
or M18 1.5 ISO 6149
15 mm [0.59 in] deep
B: M10 1.5, 16 mm [0.63 in]
deep
LS: G w. spot face or
M 12 x 1.5 ISO 6149
11.5 mm [0.45 in] deep
US version:
A: - 16 UNF O-ring boss;
15 mm [0.59 in] deep
B: M 10 1.5, 16 mm [0.63 in]
deep,
LS: 7/16 - 20 UNF o-ring boss,
11.5 mm [0.45 in] deep
mm mm A B
Type L1 [in] L2 [in] LS
129 10.4
OSPQ 80/125
47 [1.85]
[5.08] [0.41]
38 [1.50]
129 10.4 8
max. 87 [3.42]
44.4 [1.748]
25.4 [1.000]
OSPQ 80/140 L R 812.3 [3
91 [3.58]
44 [1.73]
[5.08] [0.41] .7 [ .240
3.2 ]
17]
129 10.4 T P
OSPQ 80/160
[5.08] [0.41]
132 13.0
OSPQ 100/160
[5.20] [0.51]
132 13.0 2.8 [0.110]
OSPQ 100/180
[5.20] [0.51] 45
min. 7.1 [0.280] L2 57 [2.24]
132 13.0
OSPQ 100/200 7 [0.28] 85 [3.35]
[5.20] [0.51]
44 [1.73] 102 [4.02]
135 16.2 29 [1.14]
OSPQ 125/200
[5.31] [0.64] L1
135 16.2
OSPQ 125/250
[5.31] [0.64]
140 20.8
OSPQ 160/250
[5.51] [0.82]
140 20.8
OSPQ 160/320
[5.51] [0.82]
LS
35 [1.38]
European version:
A: M18 x 1.5 ISO 6149,
15 mm [0.59 in] deep
51 [2.01]
B: M10 x 1.5, 16 mm [0.63 in] 150-594.12
deep
LS: M12 x 1.5 ISO 6149,
11.5 mm [0.45 in] deep
A B LS
mm mm
Type L1 [in] L2 [in]
197 67.8
OSPL/OSPLX 520
44 [1.73]
47 [1.85]
[7.76] [2.67]
44.4 [1.748]
25.4 [1.000]
211 82.0 82
max. 87 [3.42]
OSPL/OSPLX 630 L R 81 .3 [3.2
44 [1.73]
91 [3.58]
[8.31] [3.23] .7 [ 4
3.2 0]
T P 17]
233 104.0
OSPL/OSPLX 800
[9.17] [4.09]
263 134.0
OSPL 1000
[10.35] [5.27]
2.8 [0.110]
US version: LS
A: 3/4-16 UNF O-ring boss,
15 mm [0.59 in] deep
or for OVPL
B: M10 x 1.5, 16 mm [0.63 in]
66 [2.60]
deep
LS: 7/16-20 UNF O-ring boss,
11.5 mm [0.45 in] deep
64 [2.52]
OSPL LS with pilot pressure
relief valve:
38 [1.50]
European version:
A: for OVPL
B: M10 x 1.5, 16 mm [0.63 in]
deep
LS: G 1/4 w. spot face,
11.5 mm [0.45 in] deep LS
LS
35 [1.38]
51 [2.01]
P301 030
mm mm mm A B LS
Type L1 [in] L2 [in] L3 [in]
OSPL 288 104 52
47 [1.85]
38 [1.50]
1200 LS [10.34] [4.09] [2.05]
8
44.35 [1.746]
44.4 [1.748]
25.4 [1.000]
max. 87 [3.42]
L R 812.3 [3
91 [3.58]
44 [1.73]
.7 [ .240
3.2 ]
17]
T P
A: 3/4 - 16 UNF O-ring boss,
15 mm [0.59 in] deep
B: M10 x 1.5, 16 mm [0.63 in] deep
2.8 [0.110]
LS: 7/16 - 20 UNF O-ring boss L3
11.5 mm [0.45 in] deep min. 7.1 [0.280]
L2 45
57 [2.24]
7 [0.28]
L1 102 [4.02]
LS
35 [1.38]
51 [2.01]
150-612.10
Valve Block OVPL OVPL valve blocks can be flanged onto Sauer-Danfoss steering units type OSPL, which
are prepared for OVPL mounting.
OSPL LS
F300629
LS 150-685.10
L
L L L L
R R R R
R
T T T T
PP PP
P P P P
150-628.10 150-629.10
Connections
Valve block European version Number of Shock valve
kg [lb]
P, T, L, R: G 1/2-S** ports bar [psi]
PP: G 1/4-S**
Code Numbers and OVPL in the table below has the following valve functions incorporated:
Weights Check valve in P-port
(continued) Shock valves
Suction valves
Backpressure valve, with by-pass to reduce stand-by pressure in neutral position.
External Sauer-Danfoss
connection steering unit
L L
OVPL, 5
ports and
backpressure
valve with
by-pass
R R
T T
PP
P P
150-630.10
Connections
Valve block European version Number of Shock valve
kg [lb]
P, T, L, R: G 1/2-S** ports bar [psi]
PP: G 1/4-S**
Code Numbers and OVPL in the table below have all the following valve functions incorporated:
Weights Check valve in P-port
(continued) Shock valves
Suction valves
Backpressure valve, without by-pass.
L
L L L L
OVPL, 5 OVPL, 7
ports and ports and
backpressure backpressure
valve valve
R R R R
R
T T T T
PP PP
P P P P
150-631.10 150-632.10
Connections
Valve block European version Number of Shock valve
kg [lb]
P, T, L, R: G 1/2 - S** ports bar [psi]
PP: G 1/4 - S**
Code Numbers and OVPL in the table below has External Sauer-Danfoss
connection steering unit
Weights following valve functions incorporated:
(continued) Check valve in P-port
Shock valves L L
Suction valves
OVPL, 4 ports
R R
T T
P P
150-633.10
Connections
Valve block US version Number of Shock valve
3/4 - 16 UNF kg [lb]
ports bar [psi]
O* + S**
External Sauer-Danfoss
OVPL in the table below has the connection steering unit
T T
OVPL, 4 ports and
backpressure valve P P
with by-pass
150-634.10
Connections
Valve block US version Number of Shock valve
3/4 - 16 UNF kg [lb]
ports bar [psi]
O* + S**
Valve functions
The data below come from measurements on a representative sample of valve blocks
from production.
An oil with a viscosity of 21mm2/s [SUS] at 50C [122F] was used during measuring.
Shock valves
The shock valves protect the valve block and steering unit and limit maximum external
forces on the steering cylinder. The shock valves in the valve block limit the maximum
pressure drop from L to T and from R to T.
The shock valves are set at 10 l/min. [2.64 US gal/min].
The shock valves are of the direct acting type, so they react very quickly.
Setting tolerance: rated value +/- 10 bar [145 psi] , ex. 240 [3480 psi] +/- 10 bar [145 psi].
Suction valves
The suction valves ensure oil suction to avoid cavitations in the steering cylinder. To
provide correct suction, a back pressure valve must be fitted in the tank line from the
steering unit.
The capacity of the suction valves can be increased by building in a back pressure in the
valve block.
p p
psi bar
15
200
150 10
100
5
50
0
0 Qp
0 10 20 30 40 50 60 l/min
Qp
0 2 4 6 8 10 12 14 16 US gal/min
152-150.10
The curve below shows pressure drop across the check valve in p-connection
p p
psi bar
60 4
50
3
40
30 2
20
1
10
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 110 l/min
Qp
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 US gal/min
152-152.10
Backpressure valve
A backpressure valve increases the capacity of the suction valves.
The curve below shows pressure drop for backpressure valve without by-pass.
p p
psi bar
300
20
250
15
200
150 10
100
5
50
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 l/min
Qp
0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 25 US gal/min
152-151.10
Technical Data The curve below shows pressure drop for backpressure valve with by-pass.
(continued)
p p
psi bar
300
20
250
15
200
150 10
100
5
50
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 l/min
Qp
0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 25 US gal/min
152-178.10
Installation Connection P in the valve block must be placed over the connection P in the steering
unit, so OVPL is provided with a positioning pin to fit the positioning hole in the steering
unit.
The valve block is supplied inclusive of 2 mounting screws and 4 O-rings for building
onto the steering unit.
Tightening torque 65 5 Nm [575 44 lbfin]. It is only allowed to mount OVPL blocks on
steering units with a flat port flange, no spot face is allowed.
Dimensions 92 [3.62]
28 [1.10]
51 [2.01]
OVPL, 5 ports
16 [0.63]
European version:
P, T, L and R: B
G w. spot face, Y
15 mm (0.59 in) deep
PP: G , w. spot face,
11,5 mm (0.45 in) deep
X: 30,2 +0,2
Y: 21,3 +/- 0,2
X
95 [3.74]
44 [1.73]
US version:
P, T, L and R:
-16 UNF O-ring boss
15 mm (0.59 in) deep
X: 30,2 +0,2
44 [1.73]
29 [1.14]
B: Positioning pin
premounted in OVPL
102 [4.02]
152-149.10
Dimensions
(continued) 92 [3.62]
28 [1.10]
51 [2.01]
OVPL, 7 ports
16 [0.63]
European version: B
P, T, 2xL and 2xR: Y
G w. spot face,
15 mm (0.59 in) deep
PP: G , w. spot face,
11,5 mm (0.45 in) deep
X: 30,2 +0,2
Y: 21,3 +/- 0,2
X
B: Positioning pin
premounted in OVPL
92 [3.62]
44 [1.73]
44 [1.73]
29 [1.14] 21.5 [0.85]
X
50 [1.97]
102 [4.02]
152-148.10
Angle Block OVR OVR angle blocks are especially designed for applications in which pipes and/or hoses
must run parallel with the steering column axis, and where space is limited.
The valve block can be flanged onto Sauer-Danfoss steering unit OSPB, OSPC, OSPD,
OSPF, OSPQ and OSPL, which have no spot face around the ports.
Use the angle block makes angle and swivel connections and pipe bends unneccessary.
The OVR connections are positioned away from the steering wheel. (see dimensions
page 53)
Version OVR
L L
R R
T T F300 626
P P
150-635.10
Code Numbers and OVR in the table below has no valve functions incorporated.
Weight
Code numbers Weight
Connections
Angle block European version
P, T, L, R: G 1/2 kg [lb]
S**
Installation The valve block is supplied inclusive of 2 mounting screws and 4 O-rings for building
onto the steering unit.
Tightening torque 65 5 Nm [575 44.3 lbfin]. OVR blocks may only be mounted on
steering units with a flat port flange, (no spot facing).
For OVR blocks with other thread ore kind of valves mounted, please contact the Sauer-
Danfoss Sales organisation.
Dimensions
2.5 [0.098] max.
rmax. 0.5 [0.20]
15 [0.59]
OVR
29.4 [1.158]
29.0 [1.143]
European version:
P, T, L and R:
G , 15 mm (0.59 in) deep
140 [5.51]
106 [4.17]
38 [1.50]
91 [3.58]
25 [0.98]
100 [3.94] 46 [1.81]
152-31.10
Versions Sauer-Danfoss priority valves are used in steering systems with load sensing
steering units. In such systems steering always has first priority
Ports:
P = pump,
CF = controlled flow (priority oil flow),
EF = excess flow,
L = left,
R = right,
T = tank,
LS = load sensing,
PP = pilot pressure
OLSA 40/80
The OLSA 40 and OLSA 80 flange on priority valves are used in load sensing steering
systems, built onto OSPC LS (OLSA) steering units.
F300625
LS LS
L L CF T R R L L CF T R R
C
A B
P T EF P T EF
152B135.11 152B170.11
A: PP-damping orifice
B: LS-orifice
C: Dynamic-orifice
Versions The OLS 40, OLS 80 and OLS 120 in line priority valves are used in load sensing steering
systems together with OSPB LS, OSPC LS, OSPF LS, OSPD LS, OSPQ LS and OSPL LS
steering units.
F300624 F300623
CF EF CF EF
LS LS
P P
152B134.10 152B171.10
The OLS 160 in line priority valve is used in load sensing steering systems together with
OSPB LS, OSPC LS, OSPF LS, OSPD LS, OSPQ LS and OSPL LS steering units.
OLS 160
F300622
CF EF LS CF EF LS
PP
P T P T
152B137.11 152B172.11
Versions The priority valve OLSP 80 is to be used in connection with e.g. Sauer-Danfoss gear
(continued) pumps type SNP and steering units type OSPB LS, OSPC LS, OSPF LS, OSPD LS and OSPQ
LS in load sensing steering systems, where maximum oil flow doesnt exceed 80 l/min
[21.7 USgal/min].
OLSP 80 priority valves are to be flanged on gear pumps with outlet ports square flange
type 35 (35 mm pitch diameter of 4x M6 bolt holes for fixing the priority valve on pump).
OLSP 80
F301 266
CF EF CF EF
LS LS
P P
152B134.10 152B171.10
The priority valve OLS 320 is to be used in connection with large pumps and steering
units type OSPB LS, OSPC LS, OSPF LS, OSPD LS, OSPQ LS and OSPL LS or with EHPS
steering valve in load sensing steering systems, where maximum oil flow doesnt exceed
320 l/min [84.5 USgal/min].
OLS 320 CF EF LS
F301 470 P T
152B172.11
EHPS steering valve has build in priority
valve, but for max. pump flow 120 l/
min [31.7 USgal/min] In systems with
EHPS and pump flow between 120 l/
min [31.7 USgal/min] and 320 l/min [84.5
USgal/min] a combination of EHPS and
OLS 320 gives a good compact solution
to reduce hosing and installation cost
compared with stand alone components.
For further details of this OLS 320: look in
EHPS catalogue 520L0521. F301 471
System Sizing The steering system pump is sized so that satisfactory performance is achieved for both
steering and working hydraulics - even at idle.
Before selecting a priority valve, consider
the type of steering unit (LS static, LS dynamic or OSPF LS dynamic)
the displacement of the steering unit
the pump flow
the applications requirement for energy optimization, initial steering response time
and stability, as these all govern the selection for control spring pressure
whether the priority valve should have internal PP (Pilot Pressure) or external
PP-connection depends on the pressure drop in the pump line between the priority
valves CF-port (Controlled Flow) and the steering units P-port. With normal hose and
tube dimensions and less than 5 m distance between priority valve and steering unit,
the immediate choice is normally a priority valve with internal PP.
The following survey lists the code numbers of the priority valves that are the most
frequently used in connection with the above Sauer-Danfoss steering unit types. All
priority valves in the code number tables, except OLS 160 static, have internal PP
connection. OLS 160 static in the code number table all have external PP connection.
Code Numbers and OLS/OLSA static priority valves for load sensing static steering units
Weights OLSA 40 static and OLSA 80 static
Code Numbers
Control spring
Connections Weight
pressure
Priority valve European version US version
T,R,L: G 3/8 T, R, L: 9/16 - 18 UNF kg [lb]
bar [psi]
P, EF: G 1/2 P, EF: 7/8 - 14 UNF
OLSA 40 152B0001 - 4 [58] 2.1 [4.63]
OLSA 40 152B0002 152B0122 7 [101.5] 2.1 [4.63]
OLSA 40 152B0003 152B0124 10 [145] 2.1 [4.63]
OLSA 80 152B0016 152B0019 4 [58] 2.1 [4.63]
OLSA 80 152B0017 152B0020 7 [101.5] 2.1 [4.63]
OLSA80 152B0015 152B0125 10 [145] 2.1 [4.63]
Code Numbers and OLS/OLSA static priority valves for load sensing statics steering units
Weights OLS 120 static
(continued) Code Numbers
Connections Control spring
Weight
European version US version pressure
Priority valve
LS: G 1/4 LS: 7/16 -20 UNF kg [lb]
CF: G 1/2 CF: 3/4 - 16 UNF bar [psi]
P, EF: G 3/4 P, EF: 1 1/16 - 12 UNF
OLS 120 152B2232 152B2238 7 [101.5] 2.1 [4.63]
OLS 120 152B2233 152B2239 10 [145] 2.1 [4.63]
OLS/OLSA dynamic priority valves for load sensing dynamic steering units
OLSA 40 dynamic and OLSA 80 dynamic for OSPC LS dynamic
Code Numbers
Control spring
Connections Weight
pressure
Priority valve European version US version
T,R,L: G 3/8 T,R,L: 9/16 - 18 UNF kg [lb]
bar [psi]
P/EF: G 1/2 P/EF: 7/8 - 14 UNF
OLSA 40 152B8001 - 4 [58] 2.1 [4.63]
OLSA 40 152B8041 152B8042 7 [101.5] 2.1 [4.63]
OLSA 40 152B8046 152B8043 10 [145] 2.1 [4.63]
OLSA 80 152B8047 - 4 [58] 2.1 [4.63]
OLSA 80 152B8048 152B8044 7 [101.5] 2.1 [4.63]
OLSA 80 152B8049 152B8045 10 [145] 2.1 [4.63]
Code Numbers and OLS/OLSA dynamic priority valves for load sensing dynamic steering units
Weights OLS 40 dynamic and OLS 80 dynamic for OSPB, OSPC, OSPD, OSPQ and OSPL LS dynamic
(continued) Code Numbers
Connections Control spring
Weight
US version pressure
Priority valve European version
LS: 7/16 - 20 UNF kg [lb]
LS: G 1/4 bar [psi]
CF: 3/4 - 16 UNF
P, EF, CF: G 1/2
P, EF: 7/8 - 14 UNF
OLS 40 152B8231 - 4 [58] 1.0 [2.20]
OLS 40 152B8232 152B8253 7 [101.5] 1.0 [2.20]
OLS 40 152B8233 152B8254 10 [145] 1.0 [2.20]
OLS 80 152B8261 - 4 [58] 1.0 [2.20]
OLS 80 152B8256 152B8268 7 [101.5] 1.0 [2.20]
OLS 80 152B8257 152B8260 10 [145] 1.0 [2.20]
OLS 80 dynamic with low pressure drop (P-EF) spool for OSPB, OSPC, OSPD, OSPQ and OSPL
LS dynamic
Code Numbers
Control spring
Connections Weight
pressure
Priority valve European version
LS: G 1/4 kg [lb]
bar [psi]
P, EF, CF: G 1/2
OLS 80 152B8259 7 [101.5] 1.0 [2.20]
OLS 120 dynamic for OSPB, OSPC, OSPD, OSPQ and OSPL LS dynamic
Code Numbers
Connections Control spring
Weight
European version US version pressure
Priority valve
LS: G 1/4 LS: 7/16 -20 UNF kg [lb]
CF: G 1/2 CF: - 16 UNF bar [psi]
P, EF: G 3/4 P, EF: 1 1/16 - 12 UNF
OLS 120 152B8132 152B8143 7 [101.5] 2.1 [4.63]
OLS 120 152B8133 152B8144 10 [145] 2.1 [4.63]
OLS 160 dynamic for OSPB, OSPC, OSPD, OSPQ and OSPL LS dynamic
Code Numbers
Control Pilot
Connections
spring pressure Weight
Priority valve European version US version pressure relief valve
LS, T: G 1/4 LS, T: 1/16 -20 UNF kg [lb]
CF: G 1/2 CF: 3/4 - 16 UNF bar [psi] bar [psi]
P, EF: G 3/4 P, EF: 1 1/16 - 12 UNF
OLS 160 152B8159 152B8154 7 [101.5] 170 [2465] 4.4 [9.7]
OLS 160 152B8160 152B8155 10 [145] 170 [2465] 4.4 [9.7]
OLS 160 152B8105 - 12 [174] 170 [2465] 4.4 [9.7]
OLS 160 152B8161 152B8156 7 [101.5] 210 [3045] 4.4 [9.7]
OLS 160 152B8162 152B8157 10 [145] 210 [3045] 4.4 [9.7]
Code Numbers and OLS dynamic priority valves for OSPF LS dynamic steering units
Weights OLS 40 dynamic and OLS 80 dynamic
(continued) Code Numbers
Control spring
Connections Weight
pressure
Priority valve European version
LS: G 1/4 kg [lb]
bar [psi]
P, EF, CF: G 1/2
OLS 40 152B8031 10 [145] 1.0 [2.20]
OLS 80 152B8258 7 [101.5] 1.0 [2.20]
OLS Dynamic OLS 320 dynamic in-line/stand alone with pilot pressure relief valve, black painted
Priority Valves for OSPF Code Numbers
Control Pilot
LS Dynamic Steering Connections
spring pressure Weight
Units Priority valve European version pressure relief valve
(continued) LS, T: G kg [lb]
CF: G bar [psi] bar [psi]
P, EF: G 1
OLS 320 11006593 7 [101.5] 170 [2465] 5.9 [13.0]
OLS 320 dynamic in-line/stand alone without pilot pressure relief valve, black painted
Code Numbers
Connections Control spring
Weight
US version pressure
Priority valve
LS: 7/16 - 20 UNF kg [lb]
CF: 11/16 - 12 UN bar [psi]
P, EF: 15/16 - 12 UN
OLS 320 11007475 10 [145] 5.9 [13.0]
OLS 320 for EHPS: look in EHPS catalogue 520L0521
If you require other port connections, other control spring pressure and/or other PP
connection, go to the survey on page 50, and tick off the desired specifications, then
consult the Sauer-Danfoss Sales Organization.
Your Pump flow to OLS/OLSA at idle, l/min [USgal/min] Pump flow to OLS/OLSA at max. engine speed, l/min [USgal/min]
application
Priority OLSA 40 OLSA 80 OLS 40 OLS 80 OLS 120 OLS 160 OLSP 80 OLS 320 in-line
valve type
Spool type Standard Low pressure drop, P-EF (only OLS/OLSA 80 dynamic) No CF cut-off (only for OLS 320 for flanging on EHPS)
P, EF: G - S** P, EF: M27 2 - O*** +S** P, EF: 11/16 - 14 UNF - O***
G: CF: G - S** Metric: CF: M18 1.5 - O*** +S** UNF: CF: 3/4 - 16 UNF - O***
Ports,
LS, PP: G - S** LS: M12 1.5 - O*** +S** LS: 7/16 - 20 UNF - O***
OLS 120
EF: G - S** EF: M22 1.5 - O*** +S** EF: 7/8 - 14 UNF - O***
Ports, OLSP G: CF: G3/8 - S** Metric: CF: M18 1.5 - O*** +S** UNF: CF: 3/4 - 16 UNF - O***
80 (P: square LS: G - S** LS: M12 1.5 - O*** +S** LS : 7/16 - 20 UNF - O***
flange 35)
RV-bar 80 90 100 110 120 140 170 190 200 210 Other settings No relief valve
OLS 160
bar
OLS 320
Specification Table for Ports: PP-port only exists when external PP connection is used. T-port only exists for OLS 160 and OLS 320 with
Non Catalogue Numbers integrated pilot pressure relief vlave (RV)
of Sauer-Danfoss Priority O*: O-ring chamfer on port connections
Valves S**: Spot face around port connections
(continued)
An alternative way to specify a variant is to state an existing code number and add the
modifications, you would like to have implemented in the basic steering unit.
Requested modifications:
Technical Data
OLSA/OLS 40
P-EF P-EF
psi bar
200 14
10 bar
175 12 145 psi
150 10
7 bar
125 102 psi
8
100 4 bar
6 58 psi
75
4
50
min
25 2
0 0 Qp
0 5 10 15 20 25 30 35 40 l/min
Qp
0 1 2 3 4 5 6 7 8 9 10 US gal/min
152B139.11
OLSA/OLS 80
P-EF P-EF
psi bar
16
225 10 bar
145 psi
200 14
175 7 bar
12 102 psi
150 10 4 bar
58 psi
125 min.
8
100
6
75
4
50
25 2
0 0 Qp
0 10 20 30 40 50 60 70 80 l/min
Qp
0 2 4 6 8 10 12 14 16 18 20 US gal/min
152B80.11
OLS 120
P-EF P-EF
psi bar
16
225 10 bar
145 psi
200 14
175 12 7 bar
102 psi
150 10
125
8
100
6
min
75
4
50
2
25
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 110 120 l/min
Qp
0 5 10 15 20 25 30 US gal/min
152B165.11
OLS 160
P-EF P-EF
psi bar
20 12 bar
275 174 psi
18
250
10 bar
225 16 145 psi
200 14
7 bar
175 12 102 psi
150 10
125 min
8
100
6
75
50 4
25 2
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 l/min
Qp
0 5 10 15 20 25 30 35 40 US gal/min
152B166.10
225 16
10 bar
145 psi
200 14
175 12
7 bar
150 102 psi
10
125
8 4 bar
100 58 psi
6
75
4
50
min
25 2
0 0 Qp
0 5 10 15 20 25 30 35 40 l/min
Qp
0 1 2 3 4 5 6 7 8 9 10 US gal/min
152B174.10
OLSA/OLS 80
P-EF P-EF
psi bar
20 10 bar
275 145 psi
18
250 A+B
225 16 7 bar
14 102 psi
200
175
A+B 4 bar
12 58 psi
150 10 min
125 A+B
8 min
100
6
75 A
50 4
25 2 B
0 0 Qp
0 10 20 30 40 50 60 70 80 l/min
Qp
0 2 4 6 8 10 12 14 16 18 20 US gal/min
152B175.10
A: OLS/OLSA 80 Dynamic for OSPB, OSPC, OSPF, OSPD, OSPQ, OSPL LS Dynamic
B: OLS/OLSA 80 Dynamic with low pressure drop (P-EF) spool for OSPB, OSPC, OSPD, OSPQ, OSPL LS Dynamic
P-EF P-EF
psi bar
20 10 bar
275 145 psi
18
250 7 bar
16 102 psi
225
7 bar
200 14 102 psi
A
175 12
B
150 10
125 A
8
100 min
6
75
4
50
2
25 A+B
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 110 120 l/min
Qp
0 5 10 15 20 25 30 US gal/min
152B176.10
A: OLS 120 Dynamic for OSPB, OSPC, OSPD, OSPQ, OSPL LS Dynamic
B: OLS 120 Dynamic for OSPF LS Dynamic
OLS 160
P-EF P-EF
psi bar
450 32 12 bar
174 psi
400 28
10 bar
350 24 145 psi
7 bar
300 A 102 psi
20
7 bar
250 B 102 psi
16 A
200
12
150 min
A
100 8
50 4
A+B
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 l/min
Qp
0 5 10 15 20 25 30 35 40 US gal/min
152B177.10
A: OLS 160 Dynamic for OSPB, OSPC, OSPD, OSPQ, OSPL LS Dynamic
B: OLS 160 Dynamic for OSPF LS Dynamic
Technical Data Pressure drop P-EF for OLSP static priority valves
(continued)
OLSP 80
P-EF P-EF
psi bar
175 12
7 bar
102 psi
150 10 4 bar
58 psi
125 min
8
100
6
75
4
50
25 2
0 0 Qp
0 10 20 30 40 50 60 70 80 l/min
Qp
0 2 4 6 8 10 12 14 16 18 US gal/min
152-181.10
OLSP 80
P-EF P-EF
7 bar
psi bar 102 psi
175 12
150 10 B
4 bar
125 A 58 psi
8
100 min
6
75 A
4
50
25 2
A+B
0 0 Qp
0 10 20 30 40 50 60 70 80 l/min
Qp
0 2 4 6 8 10 12 14 16 18 US gal/min
152-182.10
A: OLSP 80 dynamic for OSPB, OSPC, OSPD, OSPQ LS dynamic
B: OLSP 80 dynamic for OSPF LS dynamic
Technical Data Pressure drop P-EF for OLS 320 static priority valves
(continued)
OLS 320
P-EF P-EF
psi bar
18
250 10 bar
16 145 psi
225
200 14
7 bar
175 12 102 psi
150 10
125 8 min.
100
6
75
4
50
25 2
0 0 Qp
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 l/min
Qp
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 US gal/min
152B185.10
OLS 320
P-EF P-EF
psi bar
450 30 10 bar
400 145 psi
25
350
7 bar
300 20 102 psi
250
15
200
150 10
min
100
5
50
0 0 Qp
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 l/min
Qp
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 US gal/min
152B186.10
Technical Data OLS 160, pilot pressure relief valve (P - T, Qp) characteristic
(continued) OLS 160 with pilot pressure relief valve is used in connection with Sauer-Danfoss
steering units without pilot pressure relief valve, normally steering unit type OSPL.
The pilot pressure relief valve protects the steering unit against excessive pressure. The
pilot pressure relief valve in OLS 160 operates with the priority valve spool in the OLS 160
to limit the maximum steering pressure P-T measured across the steering unit ports.
The pilot pressure relief valve is set when an oil flow of 80 l/min[21 US gal/min] is
supplied to OLS 160.
Setting tolerance:
rated value +10 bar [145 psi]
OLS 160
P-T P-T
psi bar
2800
190
2700
2600 180
2500
170
2400
2300 160
2200
150
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 l/min
Qp
0 5 10 15 20 25 30 35 40 US gal/min
152B141.11
Qp = Pump flow
OLS 320
HP-HT HP-HT
psi bar
3000 210
2900
200
2800
2700 190
2600 180
2500
170
2400
2300 160
2200
150
2100
0 0 Qp
0 40 80 120 160 200 240 280 320 l/min
Qp
0 10 20 30 40 50 60 70 80 US gal/min
152B187.10
Dimensions OLSA
European version:
P, EF:
G w. spot face 44 [1.73] 29 [1.14]
14 mm [0.55 in] deep Y Y
x = 34 mm [1.34 in],
max. 1,5 mm [0.06 in] deep
or M18 x 1.5 ISO 6149
14,5 mm [0.57 in] deep R L
x = 29 mm [1.14 in],
max. 1,5 mm [0.06 in] deep
or M22 x 1.5 ISO 6149,
15,5 mm [0.61 in] deep
x = 34 mm [1.34 in],
max. 1,5 mm [0.06 in] deep
T, L, R:
G 3/8 w. spot face
12 mm [0.47 in] deep
y = 34 mm [1.34 in],
max. 1,5 mm [0.06 in] deep
or M18 x 1.5 ISO 6149,
15 mm [0.59 in] deep
y = 29 mm [1.14 in],
max. 1.5 mm [0.06 in] deep
120 [4.72] 7 [0.28]
US version: 87 [3.43] X
P, EF:
7/8-14 UNF O-ring boss
P T
EF
16.7 mm [0.66 in] deep
x = 34 mm [1.34 in],
max. 1.5 mm [0.06 in] deep
87 [3.43]
EF
T, L, R:
9/16 - 18 UNF O-ring boss
12.7 mm [0.50 in] deep
y = 25 mm [0.98 in], R/CF L
max. 1.5 mm [0.06 in] deep
20 [0.79]
55 [2.17]
44 [1.73] 29 [1.14]
20 [0.79]
40 [1.57]
76 [2.99]
P T
X Y 152B81.12
European version:
P, EF:
G w. spot face X Y
15 mm [0.59 in] deep
x = 29 mm [1.14 in],
max. 1.5 mm [0.06 in] deep
or M22 x 1.5 ISO 6149
15 mm [0.59 in] deep,
x = 34 mm [1.34 in],
max. 1 mm [0.04 in] deep
40.3 [1.587]
max. 1.5 mm [0.06 in] deep P
or M18 x 1,5 ISO 6149
12 mm [0.47 in] deep,
22 [0.87]
y = 29 mm [1.14 in], PP LS
max. 1 mm [0.04 in] deep 25 [0.98]
40.3 [1.587]
LS:
EF CF
G w. spot face
12.5 mm [0.49 in] deep 41 [1.61]
z = 21mm [0.83 in], 8.9 [0.350]
8.5 [0.335]
max. 1 mm [0.04 in] deep
or M12 x 1,5 ISO 6149 19.7 [0.776]
12,5 mm [0.49 in] deep, 20.3 [0.799]
z = 22 mm [0.86 in]
0 mm deep
X
US version:
P, EF:
7/8 - 14 UNF O-ring boss
15 mm [0.59 in] deep 39 [1.54]
x = 34 mm [1.14 in],
max. 1.3 [0.05] deep
CF:
-16 UNF O-ring boss
14,3 mm [0.56 in] deep 152B136.11
y = 30 mm [1.18 in],
max. 1.3 mm [0.05 in] deep
LS:
7/16-20 UNF O-ring boss
12.5 mm [0.49 in] deep
z = 21 mm [0.83 in],
max. 1 mm [0.04 in] deep
European version:
P, EF:
G w. spot face
x = 42 mm [1.65 in],
max. 2.5 mm [0.10 in] deep
or M27 x 2 ISO 6149
x = 40 mm [1.57 in],
max. 2.5 mm [0.10 in] deep
CF: X X
G w. spot face
24 [0.94]
y = 34 mm [1.34 in], 9.1 [0.358]
56 [2.20]
max. 2.5 mm [0.10 in] deep 8.7 [0.343]
or M18 x 1.5 ISO 6149
y = 29 mm [1.14 in], CF
max. 2.5 mm [0.10 in] deep
LS, PP:
96 [3.78]
66 [2.60]
PP LS
G w. spot face
80 [3.15]
12 mm [0.47 in] deep
53 [2.09]
z = 19 mm [0.75 in]
0 mm deep
or M12 x 1,5 ISO 6149 P EF
11,5 mm [0.45 in] deep,
z = 19 mm [0.75 in] 9.1 [0.358]
Z 8.7 [0.343]
Z
0 mm deep 10 [0.39]
18.7 [0.736] 38.4 [1.512]
European version:
P, EF:
G w. spot face
x = 42 mm [1.65 in],
max. 2.5 mm [0.10 in] deep
or G 1 w. spot face
x = 47 mm [1.85 in],
max 2.5 mm [0.10 in] deep
CF:
G w. spot face
y = 34 mm [1.34 in],
max. 2.5 mm [0.10 in] deep
or G w. spot face
y = 38 mm [1.50 in], X Y
max. 2.5 mm [0.10 in] deep
178 [7.01]
LS, PP, T: 32 [1.26] 75 [2.95]
G w. spot face U
23 [0.91]
12 mm [0.47 in] deep
z = 22.8 mm [0.89 in],
P
max. 1 mm [0.04 in]deep
u = 25 mm [0.98 in]
max. 1.5 mm [0.06 in] deep T
35 [1.38]
125 [4.92]
LS PP
US version:
32 [1.26]
32 [1.26]
62.5 [2.46]
P, EF:
1 1/16-12 UNF O-ring boss
x = 41 mm [1.61 in], EF CF
max. 2.5 mm [0.10 in] deep
or 1 5/16 - 12 UNF O-ring boss 9.1 [0.36] 9.1 [0.36]
Z
Z 8.7 [0.34] 8.7 [0.34]
x = 49 mm [1.93 in],
35 [1.38] 63 [2.48] 32.5 [1.28]
max. 2.5 mm [0.10 in] deep
130 [5.12] 65 [2.56]
CF:
-16 UNF O-ring boss
y = 32 mm [1.26 in],
max. 2.5 mm [0.10 in] deep
7/8 - 14 UNF O-ring boss
y = 30 mm [1.18 in],
max. 2.5 mm [0.10 in] deep
LS, PP, T:
7/16 - 20 UNF O-ring boss X
11.5 mm [0.45 in] deep 152B138.11
z = 22,8 mm [0.89 in],
max. 1.5 mm [0.06 in] deep
u = 21 mm [0.83 in],
max. 1.6 mm [0.06 in] deep
Dimensions OLSP 80
24.7 [0.972] 24.4 [0.961]
European version: 33 [1.30] 1.88 [0.74] deep
CF:
24.7 [0.972]
G 3/8 w. spot face
43.5 [1.713]
15 mm [0.59 in] deep
31.2 [1.228]
x = 28, max. 1.5 mm [0.06 in]
deep
or
M18 1.5 ISO 6149
15 mm [0.59 in] deep
38 [1.50]
y = 29, max. 1.5 mm [0.06 in]
EF:
G w. spot face
15 mm [0.59 in] deep
y = 34, max. 1.5 mm [0.06 in]
or 84 [3.31]
M22 1.5 ISO 6149
15 mm [0.59 in] deep
X Y
x = 34, max. 1.5 mm [0.06 in]
LS:
G w. spot face
12.5 mm [0.49 in] deep
or
M12 1.5 ISO 6149
12.5 mm [0.49 in] deep
32 [1.26] 38 [1.50]
19.5 [0.768]
25 [0.98]
US version:
11 [0.04]
6.5 [0.26]
CF:
-16 UNF O-ring boss
15 mm [0.59 in] deep
x = 29 [1.14 in]
91 [3.58]
152-180.11
4 [0.16]
P, EF:
G 1 w. spot face
48 [1.89]
x = 47 mm [1.85 in]
max 1 mm [0.04 in] deep
5 [0.20]
CF: 59 [2.32] 2x16 [0.63] 3x8.5 [0.335]
G w. spot face Y
y = 34 mm [1.34 in]
max 2.5 mm [0.10 in] deep
52.5 [2.067] 63.5 [2.500]
LS, PP:
P EF
G w. spot face
14 [0.55]
Z
T:
T
117.5 [4.626]
78 [3.07]
G w. spot face
z = 25 mm [0.98 in]
max 1.5 mm [0.06 in] deep
PP
LS
47.5 [1.870]
US version:
22.5 [0.886]
CF
P, EF:
1 5/16-12 UN O-ring boss
x = 49 mm [1.93 in]
max 0.2 mm [0.01 in] deep X X
CF:
1 1/16-12 UN O-ring boss
y = 41 mm [1.61 in]
max 0.2 mm [0.01 in] deep
or
-16UNF O-ring boss
47 [1.85] 80 [3.15]
y = 30 mm [1.18 in]
max 0.2 mm [0.01 in] deep
LS, PP, T:
7/16-20 UNF O-ring boss
150H26.10
F300630
CL CR
CL CR
P
P L
L R
R T
T LS EF
LS
EF PP
PP
HP HT
HP HT
150F55.10
150F56.10
CL CR CL CR
L R L R
P P
EF EF
PP T PP T
HP LS HT HP LS HT
150F69.10 150F54.10
F301 256
OSQB CL CR OSQB CL CR
L R
P P
L
R
T
EF EF
PP PP
min. 7 bar min. 7 bar
[min. 102 psi] LS [min. 102 psi]
LS
HP HP
HT T HT
4 bar 4 bar
[58 psi] [58 psi]
P P
DR DR
OLSQ P OLSQ P
150F74.11 150F73.11
Code Numbers and OSQA and OSQB static flow amplifiers for load sensing static steering units
Weights These flow amplifiers have to be used in connection with steering units type OSPBX LS
or OSPLX LS.
OSQB/OLSQ dynamic flow amplifier for load sensing dynamics steering units.
OSQB with OLSQ has no pilot pressure relief valve.
This flow amplifier has to be used in connection with steering unit type OSPCX LS, which
has incorporated pilot pressure relief valve
If you require other amplification factors, other valve settings or other control spring
pressures, please fill in the order form on page 68 and contact the Sauer-Danfoss Sales
Organization.
Fill in your company data and place xs in the table where appropriate, then send to your Sauer-Danfoss Sales
Organization
G: (European version)
HP, EF: 1 1/4 in SAE flange
Ports, HT, CL, CR: 1 in SAE flange
OSQB/OLSQ POSQ, POLSQ, T, L, R: G 1/2
PP, LS: G 1/4
An alternative way to specify a variant is to state an existing code number and add the modifications, you would like to have implemented in the
basic flow amplifier.
Installation
The flow amplifier has to be mounted on a flat surface.
Mounting screw Tightening torque, Nm [lbf.in]
M 10 x 1.5 30 5 [265 44]
3/8 - 16 UNC 40 5 [354 44]
7/16 - 14 UNC 55 5 [487 44]
Tightening torque for fittings: Look in sub catalogue General Steering Components page 36.
Priority valve
The priority valve is used in load sensing systems where the same pump supplies oil to
both the steering system and working hydraulics. The steering system always has first
priority. Measurements were made when the pressure on the LS connection is zero.
(steering unit is in neutral position). The minimum curves apply when the pressure
on the EF connection is higher than the actual control spring pressure. The curves
for control spring pressure of 7 bar [101.5 psi] apply when the pressure on the EF
connection is zero
OSQA
HP-EF HP-EF
psi bar
150
10
7 bar
102 psi
125
8
100
6
min.
75
4
50
25 2
0 0 Qp
0 20 40 60 80 100 120 140 160 180 200 220 240 l/min
Qp
0 10 20 30 40 50 60 US gal/min
150F64.10
OSQB
HP-EF HP-EF
psi bar
200 14
175 12
7 bar
150 102 psi
10
125
8
100
6
75 min.
50 4
25 2
0 0 Qp
0 40 80 120 160 200 240 280 320 360 400 l/min
Qp
0 10 20 30 40 50 60 70 80 90 100 US gal/min
150F63.11
OSQA
HP-HT HP-HT
psi
2800 bar
190
2700
2600 180
2500
170
2400
160
2300
2200
150
0 0 Qp
0 40 80 120 160 200 240 l/min
Qp
0 10 20 30 40 50 60 US gal/min
150F67.11
OSQB
HP-HT HP-HT
psi bar
3000 210
2900
200
2800
2700 190
2600 180
2500
2400 170
2300 160
2200
150
2100
0 0 Qp
0 40 80 120 160 200 240 280 320 360 400 l/min
Qp
0 10 20 30 40 50 60 70 80 90 100 US gal/min
150F66.11
p p
psi
bar
225
15
200
175
150 10
125
100
75 5
50
25
0 0 Qp
0 40 80 120 160 200 240 280 320 360 400 l/min
Qp
0 10 20 30 40 50 60 70 80 90 100 US gal/min
150F68.10
Shock valves
The shock valves protect the flow amplifier against shock from external forces on the
steering cylinders. The shock valves in OSQA and OSQB limit the maximum pressure
drop from CL to HT and from CR to HT. The shock valves are set at 10 l/min [2.64 US gal/
min].
Setting tolerance: rated value +20 bar [290 psi].
Suction valves
The suction valves ensure oil suction on the side of the steering cylinder pistons where
in unfavorable conditions cavitation might occur. The capacity of the suction valves is
increased in OSQB by the built-in back pressure valve.
HT-CR HT-CR
HT-CL HT-CL
psi bar
150 10
100
6
4
50
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 l/min
Qp
0 5 10 15 20 25 30 35 40 US gal/min
150F35.11
POLSQ- POLSQ-
HTOSQB HTOSQB
psi bar
90
6
80
70 5
60 4
50
3
40
30 2
20
1
10
0 0 Qp
0 10 20 30 40 50 60 70 80 90 100 l/min
Qp
0 5 10 15 20 25 US gal/min
150F76.10
Dimensions
OSQA
165 [6.50]
European version:
153 [6.02]
HP, EF, HT, CL, CR: G
P, T, L, R: G 112 [4.41]
16.018 [0.631]
16.000 [0.630]
5.3 [0.21]
B: M10 x 1.5, 16 mm [0.63 in] deep 4.7 [0.19]
5 [0.20]
US version:
HP, EF, HT, CL, CR: 1 1/16 - 12 UN
A B
75.2 [2.96]
74.8 [2.94]
P, T, L, R: - 16 UNF
47 [1.85]
150.2 [5.91]
149.8 [5.90]
PP, LS: /16 - 20 UNF
7
285 [11.22]
78 [3.07]
A:
/ - 14 UNC, 21 mm [0.83 in]deep
7 16
A
B:
/ - 14 UNC, 16 mm [0.63 in] deep
7 16
16.018 [0.631]
16.000 [0.630]
16 [0.63]
120.2 [4.73]
119.8 [4.72]
17 [0.67]
150 [5.91]
129 [5.08]
121 [4.76]
56 [2.20]
41 [1.61]
125 [4.92]
86 [3.39]
68 [2.68]
31 [1.22] 31 [1.22]
55 [2.17]
86 [3.39]
125 [4.92]
150F36.11
Dimensions
OSQB 165 [6.50]
153 [6.02]
European version: 112 [4.41]
HP, EF:
82 [3.23]
1 in SAE flange min. 21 [0.83]
/ -14 UNC
7 16
16.018 [0.631]
16.000 [0.630]
18 mm [0.71 in] deep (8) 5.3 [0.21]
4.7 [0.19]
5 [0.20]
1 in SAE flange
/ - 16 UNC
3 8
75.2 [2.96]
74.8 [2.94]
47 [1.85]
30.2 [1.19]
P, T, L, R: G
150.2 [5.91]
149.8 [5.90]
PP, LS: G
285 [11.22]
78 [3.07]
A: M10 x 1,5, 21 mm [0.83 in] deep
30.2 [1.19]
B: M10 x 1,5, 16 mm [0.63 in] deep A
US version:
HP, EF:
1 in SAE flange
16.018 [0.631]
16.000 [0.630]
16 [0.63]
/ - 14 UNC
7 16
120.2 [4.73]
18 mm [0.71 in] deep (8) 119.8 [4.72]
17 [0.67] 58.7 [2.31]
P, T, L, R: - 16 UNF
PP, LS: 7/16 - 20 UNF
A:
/ - 14 UNC, 21 mm [0.83 in] deep
7 16
B: 129 [5.08]
/ - 14 UNC, 16 mm [0.63 in] deep
7 16
121 [4.76]
56 [2.20]
41 [1.61]
125 [4.92]
86 [3.39]
68 [2.68]
26.2 [1.03]
31 [1.22] 31 [1.22]
52.4 [2.06]
26.2 [1.03]
55 [2.17]
86 [3.39]
125 [4.92]
26.2 [1.03]
52.4 [2.06]
150F37.10
Dimensions
OSQB with OLSQ
European version 196 [7.72]
16.018 [0.631]
16.000 [0.630]
5.3 [0.21]
HT, CL, CR: 4.7 [0.19]
1 in SAE flange
5 [0.20]
/ - 16 UNC
3 8
POSQ, POLSQ, T, L, R: G A B
75.2 [2.96]
74.8 [2.94]
47 [1.85]
30.2 [1.19]
PP, LS, PDR: G
108 [4.25]
150.2 [5.91]
149.8 [5.90]
285 [11.22]
A:
78 [3.07]
M10 x 1.5, 21 mm [0.83 in] deep
B:
30.2 [1.19]
M10 x 1.5, 16 mm [0.63 in] deep A
16.018 [0.631]
16.000 [0.630]
16 [0.63]
120.2 [4.73]
119.8 [4.72]
17 [0.67] 58.7 [2.31]
174 [6.85]
146 [5.75]
150 [5.91]
158 [6.22]
129 [5.08]
121 [4.76]
56 [2.20]
27 [1.06]
41 [1.61]
53 [2.09]
108 [4.25]
125 [4.92]
PDR
86 [3.39]
68 [2.68]
26.2 [1.03]
31 [1.22] 31 [1.22]
View X
View X
171 [6.73]
52.4 [2.06]
26.2 [1.03]
55 [2.17]
86 [3.39]
125 [4.92]
26.2 [1.03]
52.4 [2.06]
150F75.10
Local address:
Comatrol
www.comatrol.com
Schwarzmller-Inverter
www.schwarzmueller-inverter.com
Sauer-Danfoss (US) Company Sauer-Danfoss ApS
2800 East 13th Street DK-6430 Nordborg, Denmark
Ames, IA 50010, USA Phone: +45 7488 4444
Turolla
Phone: +1 515 239 6000 Fax: +45 7488 4400
www.turollaocg.com Fax: +1 515 239 6618
www.sauer-danfoss.com
11007611 Rev BE Feb 2012