Académique Documents
Professionnel Documents
Culture Documents
Website:www.aolike.net
1, Indications
1.1 All rights of this user manual are reserved by Aolike Company.
1.2 Without Aolike company's written permission, any unit or individual is not
allowed to copy part of or total content of this user manual.
1.3 This user manual will be updated occasionally without notifying any user
except for with agreement with the user for product improvement or other
reasons. All statement, information and advice of the manual do not constitute
or hint any warranty.
1.4 The picture in this manual are just for reference, please be subject to the
actual products if anything is different.
2, Aplications
This product is widely used in hospitals, clinics or nursing home for the
examination, nursing and rehabilitation of the patients. It also can be use for
care at home.
3, Contraindications,
When improperly deal with the power line, such as the castors run over it
or the if the bed head board or other moving part squeeze the line this will
cause damage in safety. So, the patient and nurse should not make the castor
run over the line, and avoid the squeezing from the moving parts to the line.
Manufacturer should fix the powder line on the bed, avoiding damaging of
them.
4, Warning.
4.1. Its prohibited to put the heavy object on the edge on the bed board, since
it may distort, which will affect the normal use of the bed.
4.2. Its prohibited to use knife or sharp equipment to hit or scratch the bed
surface.
5, Main component
5.1, The electric bed is composed of bed board, bed frame, bed base, motor,
bedside rail and so on.
5.2, Use heavy duty silent castors with brake.(two with brake)
5.3, Use silent motor manufactured by Zhejiang jiecang motion technology
co.,Ltd or equivalent quality motor.
6, Accessories
6.1 List of accessories and related data
(8-2)
Leg
Braking status
Non-braking status
7-1
Remark:
1. Braking can be released only when they are on status of braking
2. The castor should be braked when the bed is stationary to prevent the free
slide of the bed.
7.1.2 Installation of the bed head and foot board
The bead head and foot board are disassembled for safe and space-saving in
the transportation.
7.1.2.1 Installation of the bed head and foot board
Take out the bed head and foot board, from the packing carton.
Insert them into its hold position and lock the switch.
7.1.3 Use direction of bedside rail
Turn on
Switch off
(7-3)
Warm Reminding: When lift or lower the bedside rail, pay attention to the
movement of the bedside rail, avoiding any hurt to the patient or other nearby
people.
c. Angle ruler
There is an angle ruler on the bedside rail, the angle will change to show
current angle accordingly when the bed board raise or lowers.
7.1.4 Function of bed board
The bed board is made of powder coated carbon steel cold plate, it has made
4 sections. Each section has different function as below:
Backrest section: Its the backrest for the patient. The angle of it can be
adjusted by the manual controller from 0-60
: Backrest section: its the seat for the patient, its fixed on the bed frame
and its Rotary fulcrum for its neighboring sections.
Leg section: it supports the leg of the patient. The angle of it can be
adjusted by the manual controller from 0-40
Lower leg section: it supports the leg of the patient. Its connected with the
leg section, so its adjusted accordingly when adjust the leg section by the
manual controller.
Panel control switch: It is the total switch of the control panel. Only when it
is on The LED light is green), the other bottoms can work. The light will be off
automatically in 10 seconds if there is no any moment of all the motors.
Pressing the bottom can turn it on again. (Remark: this bottom can not turn off
the control panel)
Quickly stop: It controls the power supply of all the motors. Turning it off ( the
LED Light is off) can quickly stop all the movements of the motors(Including
the movements controlled by the pedal and bedside rail). At the same time,
lock 1, lock2, lock3, lock4 will be off (The LED light of the lock is off). Pressing
it again and the LED light will be on, and all the motors can work. But please
note that the lock 1, lock2, lock3, lock4 are still on locking status, it need to
press the lock to turn it on so that its locked bottom can work.
Power light: Its LED light is on when the bed is connected normally the
power supply.
Batter light: Its LED light is on when the battery can supply the power for the
system. When it can not supply the powder, the LED Light is yellow. When the
battery is on charging, both LED lights are flashing.
Below are main function bottoms:
Raise leg: This bottom can raise the leg section of back section of the bed
board.
Lower leg: This bottom can lower the leg section of back section of the bed
board.
Raise back: This bottom can raise the back section of the bed board.
Lower back: This bottom can lower the back section of the bed board.
Raise leg and back: This bottom can raise the back section and leg section
of bed board simultaneously
Lower leg and back: This bottom can lower the back section and leg section
of bed board simultaneously
Trendelenburg: This bottom can achieve trendelenburg of the bed.
Reverse trendelenburg: This bottom can achieve reverse trendelenburg of
the bed.
Raise Hi.of bed: This bottom can raise the height of whole bed
Lower Hi. of bed: This bottom can lower the height of whole bed.
Tilt to left: This bottom can make the bed tilt to the left.
Tilt to right: This bottom can make the bed tilt to the right.
Remark: Above main function bottoms can work only when LED light of panel
control switch,quickly stop and its corresponding lock is on. Turn off Lock 1 or
Lock 1: This bottom lock bottom Raise leg and lower leg, raise leg and back,
lower leg and back ( including these functions on the control panel in the
bedside rail)
Lock 2: This bottom lock bottom Raise back and lower back raise leg and
back, lower leg and back ( including these functions on the control panel in
the bedside rail)
Lock 3: This bottom lock bottom Trendelenburg, reverse trendelenburg, Raise
Hi. of bed, Lower Hi. of bed, tilt to left and tilt to right ( including these
functions on the control panel in the bedside rail)
Lock 4: This bottom lock bottom pedal control.
Remark: TR,CPR,First aid,SL,Get out can not be locked by Lock1,Lock 2,
Lock 3,
Lock 4, they are only controlled by the bottom Quick stop.
TR: This bottom can achieve trendelenburg of the bed.
CPR: This bottom can make the bed resume to CPR position.
First aid: This bottom can make the bed achieve first aid position.
Sitting & laying: This bottom make the bed achieve sitting and lying position.
Get out: This bottom can make the bed achieve getting out position.
(Diagram 5-2)
(9-2)
(9-3)