Académique Documents
Professionnel Documents
Culture Documents
Originated in France
NORTEL CONFIDENTIAL:
The information contained in this document is the property of Nortel Networks. Except as specifically authorized in
writing by Nortel Networks, the holder of this document shall keep the information contained herein confidential and
shall protect same in whole or in part from disclosure and dissemination to third parties and use for evaluation,
operation and maintenance purposes only.
You may not reproduce, represent, or download through any means, the information contained herein in any way or in
any form without prior written consent of Nortel Networks.
The following are trademarks of Nortel Networks: *NORTEL , the NORTEL corporate logo, the NORTEL Globemark,
UNIFIED NETWORKS, S2000, S4000, S8000. GSM is a trademark of France Telecom.
All other brand and product names are trademarks or registered trademarks of their respective holders.
Copyright © 2000--2006 Nortel Networks
Nortel Confidential Publication History iii
PUBLICATION HISTORY
May 2006
Issue 15.154/EN Standard
Updated Chapter 4 Type and Class of counters to present counters by families
Removed information on BSC 12000 due to EOL (End Of Life)
Replaced all occurrences of BSC 2G with BSC 12000HC
Updated synthetic counters locators
February 2006
Issue 15.153/EN Standard
Updated definition of counter 1988 (section 5.3.2)
Updated the Q3 name of counter 3005/2 in table from section 4.1.16
November 2005
Issue 15.152/EN Standard
Updated dataflow diagram on intra--bts handover (section 2.4.3)
Updated synthetic counter 8707 (missing screenings are added to the formula)
Described toggling counters (section 3.7)
October 2005
Issue 15.151/EN Preliminary
Incorporated review comments
CR Q01206364: corrected the Q3 name of C2045 hoRequestOutgoingInterBss8W
and C2051 hoRequestOutgoingInterBssSdcch8W
Updated the definition of counters 1835 and 1809/0
July 2005
Issue 15.150/EN Draft
Updated the definitions of counter 2066, 2068, 1508, 15108/0 and 15109/0
Added a note to counter 3001/2, 3005/2
Removed the obsolete note on counters 1935, 1936, 1937, 1938, 1939 (Feature Id
22688 AMR based on traffic), and 2096 (Feature Id 15347 Network
synchronization)
Updated for CR Q01121801--02: modified the BSC 2G V15 memory threshold on
counter number (section 1.1.5)
Editorial update:
restructured Chapter 1 (created Chapter 2 on Data Flow Diagrams (DFD))
updated appendices
July 2005
Issue 15.107/EN Standard
CR Q01166072: modified the Q3 name of C1720 to radioFrameUIReceived (from
abisTrauFrameUIReceived).
June 2005
Issue 15.106/EN Standard
Updated the descriptions of the counters pcuEdgeTdma15108s0 (15108/0) and
pcuEdgeTdma15109s0 (15109/0) in section 5.9.
Updated for Feature Id 29485 V15.1.1 new counters introduction in V15.1 to avoid
interface disruption. The counters 1508, 1935, 1936, 1937, 1938, 1939, and 2096
are all reserved for future use. See also the Publication History for April 2005 for
Issue 15.103/EN Preliminary of this document.
Updated for Feature Id 28422 eMLPP support on a GSM network.
CR Q01157430: moved the counters 1086, 1087, and 1088 from section 5.4 to
section 5.2.
June 2005
Issue 15.105/EN Standard
CR Q01125865:
updated the formulas for the synthetic counters in section 5.6 (by adding the
greaterperc term where required).
reintroduced six synthetic counters in section 2.6 (8803, 8813, 9510, 9511, 9512,
9600)
Removed information on BSC6000 due to EOL.
April 2005
Issue 15.104/EN Standard
Synchronized with 15.0.1 Standard.
April 2005
Issue 15.103/EN Preliminary
CR Q01081655: updated inter--BSS handover Data Flow Diagram in section
1.2.4.5, and inter--CELL intra--BSS Data Flow Diagram in section 1.2.4.4
V15.1.1 counters added, and their value is set to 0 in V15.1:
Feature Id 15347 Network synchronization: added counter 2096
Feature Id 22688 AMR based on traffic: added counters 1935, 1936, 1937, 1938,
1939
Feature Id 29479 Paging capacity increase - UI mode - BSC 3000: added
counter 1508
Added the following counters: 1828/0, 1828/1, 1829/0, 1934/0, 2002/0, 2002/1,
2002/2, 2003/0
Integrated comments from V15.1 Draft review
Updated counter configuration list in section 4.2.1
Replaced transceiverZone/bts to bts/transceiverZone in object field of counter
descriptions
Index clean--up (phase 2)
March 2005
Issue 15.102/EN Draft
Synchronized with V15.1R Standard
Integrated late review comments from V15.0.1 Preliminary
Index clean--up (phase 1)
February 2005
Issue 15.101/EN Draft
Synchronized with V15.0.1 Preliminary
January 2005
Issue 15.100 /EN Draft
Feature Id 13913 ASCI Evolutions: updated counters 1193/8, 1722/0, 1722/1,
2052/0, 2053/0
Feature Id 25155 GPRS/EDGE Suspend and Resume:
added new counters 2066, 2067, 2068/0, 2068/1, 2071/0, 2071/1, 2072, 2073
added four new Data Flow Diagrams in new section 1.2.8 GPRS / EDGE
Suspend and Resume
Feature Id 25494 EDGE Features: updated counter 15076/0
Feature Id 22915 Extended UL TBF: updated counters 15123/0 and 15193/0
Feature Id 26186 PS Paging Duplication on BSC: updated counters 1506/0, 1507/0
and 1507/4
Feature Id 26257 Paging Load Distribution on several LAPD: updated counters
15073/0 and 15073/1
Replaced occurrences of “BSC e3” by “BSC 3000” and “TCU e3” by “TCU 3000”
(throughout the guide)
Looked for occurrences of End--Of--Life products (BTS S4000 Indoor 1900, BTS
S4000 Outdoor 1900, BTS S4000 Smart 1900, BTS S2000 Indoor 1900 and BTS
S2000E Outdoor 1900), but there was none.
January 2005
Issue 15.53/EN
CR Q00590181: added counters 1507/5 and 1803/5 in sections 1.3.16, 2.2, 2.3.1,
Update for Customer Readiness after internal review
November 2004
Issue 15.52/EN
Synchronized with V15.0 Standard
Feature Id 20571: DFD in section 1.2.10 for ASCI deleted. DFDs for main call
scenarios replace the previous ones.
counter name updates in section 4.2.1
Dictionary presentation moved from end of section 1 to beginning of section 2.
Updated locators for counters 1821 to 1827
August 2004
Issue 15.51/EN
Feature Id 20571: added section 1.2.10 for ASCI. Added counter 1193/8 in several
places.
Feature Id 23003: added section 2.2.2 for OTDI. updated counters 1722/0, 1722/1,
1723, 1724 and 1725
Feature Id 23717: added section 3.7 for Mobility Class Sensitivity Counters
Feature Id 24462: added Data Flow Diagram in section 1.2.10
Feature Id 26310: updated section 3.2.1. Added section 3.2.3
Feature Id 26479: added section 3.5 for BSCcounterlist size
CR Q00814652: added counters 1821 to 1827 in section 5.2
CR Q00934254: updated counters 1812, 1813, 1057, 1700, 1810, 1611, 1746 in
section 5.2
Updated Appendix for V15.1R counter evolutions
Reorganized Appendix for V15.x evolutions
September 2004
Issue 15.23/EN Standard
August 2004
Issue 15.22/EN Preliminary
CR Q00964502 -- updated counters 1164/28 and 1164/32.
Removed parens from three counter locator names so WorldView will work.
August 2004
Issue 15.21/EN Preliminary
CR Q00956890 - updated counter 1803/4.
Issue 15.20/EN Preliminary
CR Q00956244 -- updated notes (Stating not implemented for v14.3 or v15) on
counters 3002, 3003, 3006, and 3007.
August 2004
Issue 15.19/EN Preliminary
CR Q00953889 -- removed counter 1163/29.
July 2004
Issue 15.18/EN Preliminary
CR Q00955246 - removed the string “Tch” from the counter names for counters
1065/1, 1066/1, 1067/1, and 1068/1.
Issue 15.17/EN Preliminary
Preparation for Helmsman release
July 2004
Issue 15.16/EN Preliminary
CR Q00941508 - multiple changes and additions from comments CR.
July 2004
July 2004
June 2004
June 2004
May 2004
Issue 15.07/EN Preliminary
Incorporated Counter name changes 1772/0, 1772/1, and 1773/0, 1773/1 received
from email remarks.
Incorporated Counter definitions 15132/0 thru 15189/0 received from email
remarks.
Incorporated CR Q00873161 updated counters 1611/3, 1612/0, and 1612/1.
Added Feature 26797 - Directed Retry Counters
CR Q00184739--05 -- Counter 1721 name changed from
Erroneous_Frame_Number to ECU_Activation.
April 2004
Issue 15.06/EN Preliminary
Incorporated SME review comments.
March 2004
Issue 15.05/EN Preliminary
For CR Q00836666, deleted counters 3000/1, 3001/1, 3004/2 and 3005/1.
March 2004
Issue 15.04/EN Preliminary
Update for review comments.
For CR Q00835972--01, deleted 1835 counters cardSynthLoadBscb<x> and
cardSynthLoadTscb<x>.
March 2004
Issue 15.03/EN Preliminary
For CR Q00835972--01, deleted information concerning the 1835
cardSynthLoadBscb<x>Moy/Max counters.
For CR Q00792758, changed the description of SDCCH and changed the functions
of counter numbers 1609/2 and 1611/2.
For CR Q00841812
Modified features:
15015 GPRS TBF establishment improvement: one phase access
New features:
20219 EDGE link adaptation
January 2004
Issue 15.02/EN Draft
For CR Q00707442--01, incorporated minor changes.
December 2003
Issue 15.01/EN Draft
Modified features:
19174 EDGE Dynamic ABIS and AGPRS backhaul
20231 EDGE Traffic Management
22463 WPS BSS2G and E3 queuing mechanism enhancement
22464 WPS BSS2G and E3 access class barring with class periodic rotation
22465 WPS BSS2G and E3 public access bandwidth protection
October 2003
Issue 14.11/EN Standard
August 2003
Issue 14.10/EN Preliminary
Added AMR V14 counters in appendix A.
Added new BSC 2G V14 counters and BSCe3 V14 counters in Appendix A.
Checked the AMR and e3 counters.
Added the following e3 counter description: 3002, 3003, 3006, 3007, 1507/0,
1507/1, 1507/2, 1507/3, 1507/4.
Added the following AMR counter description: 1197/2, 1197/3, 1780/1, 1780/2,
1906/0, 1917/1, 1929/1.
Modified the following counter description: 1780/0, 1917/0, 1929/0.
Added the following V14.3 counter description: 1816/0, 1817/0, 1818/0, 1819/0,
1820/0.
Modified the name of the following counters: 1803/0, 1803/1, 1803/2, 1803/3,
1803/4,
April 2003
Issue 14.09/EN Preliminary
Taken into account:
internal comments
CR Q00548005 (correction, counters 15028/1 and 15030/1)
CR Q00566940 (correction, Annex of the document)
CR Q00581808 (counters 15005/0 and 15005/1)
CR Q00581804 (counters 15005/0 and 15005/1)
CR Q00614305 (counters 1606, 1607, 1608, 1701, 1609, 1611, 1613, 1700)
January 2003
Issue 14.07/EN Preliminary
Taken into account:
CR Q00411337
CR Q00548005
CR Q00500889
CR Q00470148
CR Q00431517
CR Q00431468
CR Q00389797
CR Q00252063
CR Q00252054
CR Q00208602
CR Q00583446
CR Q00582009
CR Q00566940
December 2002
November 2002
October 2002
August 2002
Issue 13.06/EN Standard
Minor editorial update
Issue 13.05/EN Preliminary
The following modifications have been made to the manual:
Chapter 1 “Introduction”
• Modified the following PCUSN Data Flow Diagrams (paragraph 1.2.9):
– BVC flow control and MS flow control mechanisms
– Discard of LLC PDUs
– Establishment of an UL TBF in two phases access with first phase in
CCCH
– Establishment of an UL TBF during DL TBF
– Normal UL TBF release
– Abnormal release of an UL TBF due to non progression of V(Q)
– Abnormal release of an UL TBF due to non progression of V(Q) during full
duplex transfer in the case that the DL TBF is also released
– Non response from the mobile station after N3101 scheduled blocks
(means with USF set in downlink)
– Non response from the mobile station after N3101 scheduled blocks
(means with USF set in downlink) during full duplex transfer, in the case
that the DL TBF is also released
– Non response from the mobile after UP_NASSIGNMAX Packet Uplink
Assignment messages
– Non progression from the mobile after UP_NASSIGNMAX Packet
Uplink Assignment messages during full duplex transfer, in the case that
the DL TBF is also released
– Non response from the mobile after N3103 Packet Uplink Ack/Nack sent
with FAI=1
– Non response from the mobile after N3103 Packet Uplink Ack/Nack sent
with FAI=1 during full transfer, in the case that the DL TBF is also released
– Paging procedure initiated by the network for downlink packet transfer
towards a MS in standby state
– Downlink establishment towards a mobile in Ready State and Packet Idle
Mode
– Establishment with Packet Downlink Assignment and Packet Timeslot
Reconfigure
– 15031/1 FirstDlUnitDataFrame
– 15031/2 dlTBFAllocFailure
– 15031/3 dlTBFRadioFailure
– 15032/3 ulsecondPhaseAllocFailure
– 15034/0 PDANWithUlReq
– 15036/0 ulsecondPhaseRadioFailure
– 15041/0 upUserdatablocks
– 15043/0 RequestedRetransmittedDataBlocksDN
– 15058/4 dnPipebetween22and33kbps
– 15061/0 upPipeless11kbps
June 2002
Issue 13.04/EN Draft
March 2002
Issue 13.03/EN Standard
Changed to Standard - minor editorial update
August 2001
July 2001
Issue 13.01/EN Draft
July 2001
Issue 12.09/EN Standard
The following changes were made in individual chapters:
Chapter 1 “Introduction”
• integrated the following data flow diagrams (DFDs):
– Immediate assignment: paging (normal completion), Paragraph 1.2.2.2
May 2001
Issue 12.08/EN Preliminary
V12.4 release update after internal review
The following changes were made in individual chapters:
Chapter 1 “Introduction”
• created Paragraph 1.3.3 “PDTCH resources”
• integrated the following data flow diagrams (DFDs):
– immediate assignment (normal completion), Paragraph 1.2.2.1
– queuing in the assignment procedure (successful completion),
Paragraph 1.2.2.3
– dedicated channel assignment (normal completion), Paragraph 1.2.3.1
– dedicated channel assignment (no resource available), Paragraph 1.2.3.3
– inter--cell intra--bss handover (normal completion with communication on
TRAFFIC phase), Paragraph 1.2.4.4
– connection clearing required by the MSC (normal completion),
Paragraph 1.2.5.2
– GPRS procedure (normal completion), Paragraph 1.2.7.1
– GPRS procedure (no resource available for PDTCH preemption),
Paragraph 1.2.7.2
– GPRS procedure (negative acknowledgement by the PCU after the BSC
attempted to preempt a PDTCH to make a TCH channel),
Paragraph 1.2.7.3
Chapter 2 “Counter description”
• updated existing “Dataflows” fields and created new ones
April 2001
Issue 12.07/EN Draft
The following changes were made in individual chapters:
Chapter 1 “Introduction”
• created Paragraph 1.2.7 “GPRS” and added three data flow diagrams (DFDs):
– GPRS procedure (normal completion)
– GPRS procedure (no resource available for PDTCH preemption)
– GPRS procedure (negative acknowledgement by the PCU after a PDTCH
preemption)
– gave the list of the 193 counters impacted by the circuit/packet aspect
• created new DFDs:
– dedicated channel assignment (no resource available)
– queuing in the assignment procedure (normal completion)
• updated existing DFDs:
– immediate assignment (normal completion)
– dedicated channel assignment (normal completion)
– intercell handover (normal completion)
– connection clearing required by the MSC (normal completion)
Chapter 2 “Counter description”
• Answer to Service Requests:
– NK10370: corrected counter number for counters 15053/0
nbSamplesUpQuality and 15053/1 nbSamplesDnQuality
– NK10371: corrected counter number for counters 15058/2
dnTbfImmediateAssignment and 15058/1 upTbfImmAssigRejectNoPdch
– NK10231: updated definition of counter 1057
– EE10113: updated definition of counter 1057
– NK10245: added DFDs for the following counters: 1039, 1052, 1057,
1609, 1611, 1812, 1813, 1814, 1815
– NK10200: updated definition of counters 1812 and 1813
– SR 30349641 (master SR 30318353): updated definition of counter 1812
– HK10522: updated definition of counters 1609/0, 1609/2, 1611/0, 1611/2
– ER10013: updated definition of counter 1700
• updated the definition of all the counters concerned by TCH/FR and
preempted PDTCH
• updated the availability date of PCUSN counters (Paragraph 2.8)
March 2001
Issue 12.06/EN Draft
V12.4 release update after internal review
The following changes were made in individual chapters:
Chapter 2 “Counter description”
• updated the description of the triggering event of C15029/1, C15029/2,
C15029/3, C15029/4, C15031/1, C15031/2, C15031/3, C15031/4
• updated the description of the function of C15039, C15040/0, C15042/0,
C15042/2, C15044
January 2001
Issue 12.05/EN Draft
The following changes were made in individual chapters:
Chapter 2 “Counter description”
• Answer to Service Requests:
– SR 30330395 (30430423): removed C15057/5 lossOfComNT1001
– SR EE00526 (30340254): added to
C9500 bscSdcchAveragedUsedMoy/Max/Ech/Cum and to
C9501 bscTchFrAveragedUsedMoy/Max/Ech/Cum, Paragraph 2.5
• completed the description of PCUSN counters, Paragraph 2.8
• added data flow diagrams to the description of counters C1812, C1813,
C1814, and C1815, Paragraph 2.1
September 2000
Issue 12.04/EN Standard
The following changes were made in individual chapters:
Chapter 2 “Counter description”
• Answer to Service Requests:
– EE00525 C1839/n and C1840/n location is not on bts object, but on
adjacentCellHandOver object
• completed the description of C1161/5, and C1629/0
• added three synthetic GSM--R specific counters: C8912, C8913, and C8919
June 2000
Issue 12.03/EN Preliminary
March 2000
Issue 12.02/EN Draft
V12.4 release update
The following changes were made in individual chapters:
Chapter 2 “Counter description”
• added GPRS counters
• added counters related to feature TF995 “Automatic cell tiering”
January 2000
Issue 12.01/EN Draft
Creation:
Chapter 1 “Introduction” contains the former Chapter 4 “BSS observation
principles” which was removed from Manual < 07 >.
Chapter 2 “Counter description” contains the former Chapter 5 “Dictionary of
observation counters” which was removed from Manual < 07 >.
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-- 1
2.8.2 GPRS/EDGE Suspend procedure with RAU message (failure case) . . 2--136
2.8.3 GPRS/EDGE Suspend procedure with Resume message
(nominal procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--138
2.8.4 GPRS/EDGE Suspend procedure with Resume message
(failure case) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--139
2.9 BSC equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--142
2.9.1 CPUE overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--142
2.10 PCUSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--143
2.10.1 Flow control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--143
2.10.2 LLC Discarded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--144
2.10.3 UL TBF Establishment: Normal Completion . . . . . . . . . . . . . . . . . . . . . . . 2--146
2.10.4 UL TBF Establishment: UL TBF Establishment during DL transfer . . . 2--148
2.10.5 UL TBF Release: Normal Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--150
2.10.6 Abnormal OL TBF Release: lossOfComNN0002 . . . . . . . . . . . . . . . . . . . 2--152
2.10.7 Abnormal UL TBF Release (FULL Duplex): LossOfComNN0002 . . . . . 2--154
2.10.8 Abnormal UL TBF Release: N3101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--156
2.10.9 Abnormal UL TBF Release (FULL Duplex): N3101 . . . . . . . . . . . . . . . . . 2--158
2.10.10 Abnormal UL TBF Release: UP_NASSIGNMAX . . . . . . . . . . . . . . . . . . . 2--160
2.10.11 Abnormal UL TBF Release (FULL Duplex): UP_NASSIGNMAX . . . . . 2--163
2.10.12 Abnormal UL TBF Release: N3103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--166
2.10.13 Abnormal UL TBF Release (FULL Duplex): N3103 . . . . . . . . . . . . . . . . . 2--168
2.10.14 DL TBF Establishment: MS in Standby State . . . . . . . . . . . . . . . . . . . . . . 2--170
2.10.15 DL TBF Establishment: MS in Ready State . . . . . . . . . . . . . . . . . . . . . . . 2--173
2.10.16 DL TBF Establishment during UL transfer . . . . . . . . . . . . . . . . . . . . . . . . 2--175
2.10.17 DL TBF Release: Normal Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--176
2.10.18 Abnormal DL TBF Release: lossOfComNN0002 . . . . . . . . . . . . . . . . . . . 2--178
2.10.19 Abnormal DL TBF Release (FULL Duplex): lossOfComNN0002 . . . . . 2--180
2.10.20 Abnormal DL TBF Release: N3105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--183
2.10.21 Abnormal DL TBF Release (FULL Duplex): N3105 . . . . . . . . . . . . . . . . . 2--185
2.10.22 Abnormal DL TBF Release: DN_NASSIGNMAX . . . . . . . . . . . . . . . . . . . 2--188
2.10.23 Abnormal DL TBF Release (FULL Duplex): DN_NASSIGNMAX . . . . . 2--190
2.10.24 Abnormal DL TBF Release: No final PDAN . . . . . . . . . . . . . . . . . . . . . . . 2--193
2.10.25 Abnormal DL TBF Release (FULL Duplex): No final PDAN . . . . . . . . . . 2--195
2.10.26 Preemption of radio timeslots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--198
2.10.27 Cell update: Packet Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--200
2.11 Advanced Speech Call Items (ASCI) (GSM--R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2--203
Applicability
This document applies to the V15.1.1 system release.
This document is part of the BSS Nortel Networks Technical Publications (NTPs).
It is closely associated with the following manuals:
The BSS Operating Principles manual (NTP < 07 >) describes general operating
principles and explains the mechanisms that enable Man-Machine interface
commands.
The BSS Parameter Dictionary (NTP < 124 >) contains all the parameters used
in OMC--R commands.
The OMC--R User Manual (NTPs < 128 >, < 129 > and < 130 >) is a
user-oriented guide to performing Human-Machine interface commands.
The BSS Operating Procedures Manual (NTP < 34 >) describes various
procedures that help users operate or reconfigure a BSS.
Precautionary message
The following message:
CAUTION
GSM--R specific
Indicates that specific equipment and specific software (such as
specific software in the BSC) dedicated to Railway application is
used and that the feature is therefore not available for all standard
GSM users.
Some GSM--R specific counters listed in this dictionary contain “(GSM--R V12)”
in the “Feature” field because they were introduced in V12.
Audience
This document is intended for:
OMC--R administrators
OMC--R maintenance attendants
GSM network engineers
users who want to know more about OMC--R
Prerequisites
Users must be familiar with networking principles.
They must also be familiar with the following manuals :
< 00 > : BSS Product Documentation Overview
< 01 > : BSS Overview
< 06 > : OMC--R Architecture and Reference Manual
< 07 > : BSS Operating Principles
< 32 > : OMC--R Preventive and Corrective Maintenance Manual
< 34 > : BSS Operating procedures
< 124 > : BSS Parameter Dictionary
< 128 > : OMC--R User Manual -- Volume 1 of 3: Object and Fault menus
< 129 > : OMC--R User Manual - Volume 2 of 3: Configuration, Performance,
and Maintenance menus
< 130 > : OMC--R User Manual - Volume 3 of 3: Security, Administration,
SMS--CB, and Help menus
Vocabulary conventions
The glossary is presented in Manual < 00 >.
1 INTRODUCTION
Figure 1--1 provides the user with guidelines for locating a BSS observation counter
in the dictionary of counters, starting from different points.
Starting point
sdcchAllocated
SDCCH resource Yes
sdcchAveragedUsed
available allSdcchAllocatedTime (possibly)
No
No
sdcchRessourceFailure
Attempt of allocation
of a TCH
tchQueueingExpiration (cause =
highest priority or internal priority)
Each time a queueing tchAverageQueueLength (cause =
request is extracted highest priority or internal priority)
from a queue on timer tchQueueingDuration
expiration
1748
1702
1191/n (1)
1730 (1)
1606
1607
1744 (2)
1746 (2)
1609/2 (2)
1611/2 (2)
CHANNEL_ACTIVATE
Set timer TchnAck
1629/0
CHANNEL_ACTIVATE_ACK
START_MEASUREMENT_REQ_ACK
DTAP (CM_SERVICE_ACCEPT)
1107
DTAP (CM_SERVICE_ACCEPT) 1501
CM_SERVICE_ACCEPT
ALERTING
DTAP (ALERTING)
DTAP (ALERTING)
1108
1500
(1) The following counters are incremented depending on the cause value in the
CHANNEL REQUIRED message:
1191 cause 000
1191/1 and 1730 for cause 001
1191/2 for cause 010
1191/3 for cause 011
1191/4 and 1730 for cause 100
1191/5 for cause 101
1191/6 for cause 110
1191/7 for cause 111
(2) If no SDCCH is available, the BSC may try to allocate a TCH in signaling mode.
In this case, the following counters are incremented: 1744, 1746, 1609/2, 1611/2
List of the counters incremented during this procedure:
This procedure used to establish group calls (VCS or VGCS) includes Originator
To Dispatcher Information (OTDI) in the setup message.
1748
1702
1191/n (1)
1730 (1)
1606
1607
1744 (2)
1746 (2)
1609/2 (2)
1611/2 (2)
CHANNEL_ACTIVATE
Set timer TchnAck
1629/0
CHANNEL_ACTIVATE_ACK
START_MEASUREMENT_REQ_ACK
DTAP (CM_SERVICE_ACCEPT)
1107
DTAP (CM_SERVICE_ACCEPT) 1501
CM_SERVICE_ACCEPT
ALERTING
DTAP (ALERTING)
DTAP (ALERTING)
1108
1500
PAGING_COMMAND 1107
PAGING_COMMAND 1503
CHANNEL_REQUIRED
CHANNEL_REQUIRED
1748
1702
1191/n (1)
1730 (1)
1606
1607
1744 (2)
1746 (2)
1609/2 (2)
1611/2 (2)
CHANNEL_ACTIVATE
Set timer TchnAck
1629/0
CHANNEL_ACTIVATE_ACK
Reset timer TchnAck
IMMEDIATE_ASSIGNMENT_COMMAND
IMMEDIAT_ASSIGNMENT Set timer T3101
1749
SABM (PAGING_RESPONSE) 1192/n
ESTABLISH_INDICATION
Reset timer T3101
1750
1193/n CONNECTION_REQUEST
1195 or 1196 (PAGING_RESPONSE)
1108
1502 CONNECTION_CONFIRM
1105
START_MEASUREMENT_REQUEST 1104
START_MEASUREMENT_REQ_ACK
DTAP (SETUP)
1107
DTAP (SETUP)
SETUP 1501
ALERTING
DTAP (ALARTING)
DTAP (ALARTING)
1108
1500
(1) The following counters are incremented depending on the cause value in the
CHANNEL REQUIRED message:
1191/0 for cause 000
1191/1 and 1730 for cause 001
1191/2 for cause 010
1191/3 for cause 011
1191/4 and 1730 for cause 100
1191/5 for cause 101
1191/6 for cause 110
1191/7 for cause 111
(2) If no SDCCH is available, the BSC may try to allocate a TCH in signaling mode.
In this case, the following counters are incremented:
1744, 1746, 1609/2, 1611/2
List of the counters incremented during this procedure:
1748
1191/0
1608
1751
1611/1 (1)
IMMEDIATE_ASSIGNMENT_COMMAND
(IMMEDIATE_ASSIGNMENT_REJECT)
IMMEDIATE_ASSIGNMENT_REJECT
ACTIVATE_NEGATIVE_ACK
DEACTIVATE_SACCH
Reset timer T3101 Reset timer TchnAck
1606
1607
DEACTIVATE_ACK
1751
1161/2
IMMEDIATE_ASSIGNMENT_COMMAND
(IMMEDIATE_ASSIGNMENT_REJECT)
IMMEDIATE_ASSIGNMENT_REJECT
(1) The following counters are incremented depending on the cause value in the
CHANNEL REQUIRED message:
1191/0 for cause 000
1191/1 and 1730 for cause 001
1191/2 for cause 010
1191/3 for cause 011
1191/4 and 1730 for cause 100
1191/5 for cause 101
1191/6 for cause 110
1191/7 for cause 111
(2) If no SDCCH is available, the BSC may try to allocate a TCH in signaling mode.
In this case, the following counters are incremented:
1744, 1746, 1609/2, 1611/2
1607
1751
Reset timer TchnAck
Reset timer T3101 1161/3
IMMEDIATE_ASSIGNMENT_COMMAND
(IMMEDIATE_ASSIGNMENT_REJECT)
IMMEDIATE_ASSIGNMENT_REJECT
(1) The following counters are incremented depending on the cause value in the
CHANNEL REQUIRED message:
1191/0 for cause 000
1191/1 and 1730 for cause 001
1191/2 for cause 010
1191/3 for cause 011
1191/4 and 1730 for cause 100
1191/5 for cause 101
1191/6 for cause 110
1191/7 for cause 111
(2) If no SDCCH is available, the BSC may try to allocate a TCH in signaling mode.
In this case, the following counters are incremented:
1744, 1746, 1609/2, 1611/2
IMMEDIATE_ASSIGNMENT_COMMAND
(IMMEDIATE_ASSIGNMENT)
Reset timer TchnAck
Timer T3101 expired
1749
IMMEDIATE_ASSIGNMENT 1192/n
RF_CHANNEL_RELEASE
Set timer TrfAck
RF_CHANNEL_RELEASE_ACK
Reset timer TrfAck
1607 (--1)
(1) The following counters are incremented depending on the cause value in the
CHANNEL REQUIRED message:
1191/0 for cause 000
1191/1 and 1730 for cause 001
1191/2 for cause 010
1191/3 for cause 011
1191/4 and 1730 for cause 100
1191/5 for cause 101
1191/6 for cause 110
1191/7 for cause 111
(2) If no SDCCH is available, the BSC may try to allocate a TCH in signaling mode.
In this case, the following counters are incremented:
1744, 1746, 1609/2, 1611/2
IMMEDIATE_ASSIGNMENT_COMMAND
(IMMEDIATE_ASSIGNMENT)
Reset timer TchnAck
1749
IMMEDIATE_ASSIGNMENT 1192/n
SABM
ESTABLISH_INDICATION
CHANNEL_RELEASE
Reset timer T3101
CHANNEL_RELEASE
DEACTIVATE_SACCH
Set timer TdeacAck
RF_CHANNEL_RELEASE_ACK
Reset timer TrfAck
1607 (--1)
(1) The following counters are incremented or decremented depending on the cause
value in the CHANNEL REQUIRED message:
1191/0 for cause 000
1191/1 and 1730 for cause 001
1191/2 for cause 010
1191/3 for cause 011
1191/4 and 1730 for cause 100
1191/5 for cause 101
1191/6 for cause 110
1191/7 for cause 111
(2) If no SDCCH is available, the BSC may try to allocate a TCH in signaling mode.
In this case, the following counters are incremented:
1744, 1746, 1609/2, 1611/2
List of the counters incremented or decremented during this procedure:
Data Flow Diagram: immediate assignment failure procedure: traffic with the MSC
closed
1748
1191/0
1751
1611/0 (1)
IMMEDIATE_ASSIGNMENT_COMMAND
(IMMEDIATE_ASSIGNMENT_REJECT)
IMMEDIATE_ASSIGNMENT_REJECT
1748
1702
1191/n (1)
1730 (1)
1606
1607
1744 (2)
1746 (2)
1609/2 (2)
1611/2
CHANNEL_ACTIVATE (2)
Set timer T3101
Set timer TchnAck
1629/0
CHANNEL_ACTIVATE_ACK
START_MEASUREMENT_REQ_ACK
Set timer TchnAck
CONNECTION_CONFIRM
1105
Reset timer Tmea CONNECTION_FAILURE 1104
DEACTIVATE_SACCH
1753
1778
1044
1045
STOP_MEASUREMENT_REQUEST
CLEAR_REQUEST
1108
1502
DEACTIVATE_ACK
Set timer TdeacAck
STOP_MEASUREMENT_ACK
CLEAR_COMPLETE
Timer T3109 expires
1108
1502
RF_CHANNEL_RELEASE
Set timer TrfAck
(1) The following counters are incremented depending on the cause value in the
CHANNEL REQUIRED message:
1191/0 for cause 000
1191/1 and 1730 for cause 001
1191/2 for cause 010
1191/3 for cause 011
1191/4 and 1730 for cause 100
1191/5 for cause 101
1191/6 for cause 110
1191/7 for cause 111
(2) If no SDCCH is available, the BSC may try to allocate a TCH in signaling mode.
In this case, the following counters are incremented:
1744, 1746, 1609/2, 1611/2
1748
1702
1191/n (1)
1730 (1)
1606
1607
1744 (2)
1746 (2)
1609/2 (2)
1611/2 (2)
CHANNEL_ACTIVATE
Set timer TchnAck Set timer T3101
1629/0
CHANNEL_ACTIVATE_ACK
IMMEDIATE_ASSIGNMENT_COMMAND
Reset timer TchnAck (IMMEDIATE_ASSIGNMENT)
IMMEDIATE_ASSIGNMENT
1749
SABM 1192/n
(CM_SERVICE_REQUEST) ESTABLISH_INDICATION
(CM_SERVICE_REQUEST)
Reset timer T3101
1750
1193/n CONNECTION_REQUEST
1195 or 1196 (L3_INFORMATION
CM_SERVICE_REQUEST)
1108
1502
START_MEASUREMENT_REQUEST
CONNECTION_CONFIRM
CLEAR_REQUEST
Set timer TrelREQ
1108
1502
CLEAR_COMMAND
Reset timer TclrCMD
1107
1503
CLEAR_COMPLETE
Reset timer TrelREQ
1108
1502
RELEASE_CONFIRM
Set timer TdeacAck
DEACTIVATE_SACCH
Reset timer TdeacAck
DEACTIVATE_ACK
Set timer T3109
RF_CHANNEL_RELEASE
Timer T3109 expires
RF_CHANNEL_RELEASE_ACK
Set timer TrfAck
(1) The following counters are incremented depending on the cause value in the
CHANNEL REQUIRED message:
1191/0 for cause 000
1191/1 and 1730 for cause 001
1191/2 for cause 010
1191/3 for cause 011
1191/4 and 1730 for cause 100
1191/5 for cause 101
1191/6 for cause 110
1191/7 for cause 111
(2) If no SDCCH is available, the BSC may try to allocate a TCH in signaling mode.
In this case, the following counters are incremented:
1744, 1746, 1609/2, 1611/2
(3) ASCI counters are optional since they are related to the GSM--R functionality.
List of the counters incremented or decremented during this procedure:
Data Flow Diagram: immediate assignment failure procedure: rejection from the
MSC
1748
1702
1191/n (1)
1730 (1)
1606
1607
1744 (2)
1746 (2)
1609/2 (2)
1611/2 (2)
CHANNEL_ACTIVATE
Set timer TchnAck
1629/0
CHANNEL_ACTIVATE_ACK
Set timer T3101
Reset timer TchnAck IMMEDIATE_ASSIGNMENT_COMMAND
(IMMEDIATE_ASSIGNMENT)
IMMEDIATE_ASSIGNMENT
1749
SABM 1192/n
(CM_SERVICE_REQUEST) ESTABLISH_INDICATION
(CM_SERVICE_REQUEST)
Reset timer T3101
1750
1193/n CONNECTION_REQUEST
1195 or 1196 (L3_INFORMATION
CM_SERVICE_REQUEST)
1108
1502
START_MEASUREMENT_REQUEST
CONNECTION_CONFIRM
1108
1502
CHANNEL_RELEASE
DEACTIVATE_SACCH
Set timer TdeacAck
DEACTIVATE_ACK
Reset timer TdeacAck
STOP_MEASUREMENT_REQUEST
Set timer Tend
STOP_MEASUREMENT_ACK
Reset timer Tend Set timer T3109
RELEASE_INDICATION
Reset timer T3109
RF_CHANNEL_RELEASE
Set timer T3111 Set timer TrfAck
RF_CHANNEL_RELEASE_ACK
Timer T3111 expires Reset timer TrfAck
1607 (--1)
DISCONNECTED_INDICATION
1105 (--1)
(1) The following counters are incremented depending on the cause value in the
CHANNEL REQUIRED message:
1191/0 for cause 000
1191/1 and 1730 for cause 001
1191/2 for cause 010
1191/3 for cause 011
1191/4 and 1730 for cause 100
1191/5 for cause 101
1191/6 for cause 110
1191/7 for cause 111
(2) If no SDCCH is available, the BSC may try to allocate a TCH in signaling mode.
In this case, the following counters are incremented:
1744, 1746, 1609/2, 1611/2
(3) DTAP service is now open
(4) ASCI counters are optional since they are related to the GSM--R functionality.
List of the counters incremented or decremented during this procedure:
1107
1503
1841/0
1744
1746
1609/0
CONN_STATE_REQ 1611/0 (1)
1812
1094
1095
CONN_STATE_REQ_ACK
CHANNEL_ACTIVATE
Set timer TchnAck
1197/0 or 1197/1
or 1709 and 1705/n (2)
or 1710 and 1707/n
CHANNEL_ACTIVATE_ACK
Reset timer TchnAck
ASSIGNMENT_COMMAND
Set timer T3107
ASSIGNMENT_COMMAND
1049
1715 (3)
STOP_MEASUREMENT_REQUEST
STOP_MEASUREMENT_ACK
1601
1602
1603
1622
1623
1624
1625
1626
1805
1806
SABM 1807
1808 (4)
UA ESTABLISH_INDICATION
RF_CHANNEL RELEASE
Set timer TrfAck
1044
1045
RF_CHANNEL RELEASE_ACK
Reset timer TrfAck
1607(--1) (4)
1717
1718
1719
1720
1721
(1) When a TCH resource is successfully allocated internally in the BSC software,
the following counters are incremented:
1609/0 tchFrAllocatedTchAllocation (number of TCH/FR allocated for traffic in
the inner or outer zone of the cell)
1611/0 tchFrAveragedUsedTchAllocationMoy/Max/Cum/Ech (average number
of TCH/FR used for traffic in the inner or outer zone of the cell)
1812 allocatedCircuitTsMoy/Max/Cum/Ech (number of TS allocations for
traffic on circuit mode in the cell or
allocatedCircuitTsTrZoneMoy/Max/Cum/Ech (number of TS allocations for
traffic on circuit mode in the inner or the outer of the cell
(2) The counter incremented depends on the channel mode used (speech or data):
either 1197/0 (FR) or 1197/1 (EFR) for speech
or 1709 and 1705/n (n=0 to 6) for transparent data
or 1710 and 1707/n (n=0 to 2) for non--transparent data
(3) When the ASSIGNMENT_COMMAND message is received, 1049
attemptedTchFrSeizures (number of TCH/FR assignment requests) is incremented
and, if the MS is the dualband type, 1715 attempted TchFrSeizuresMsDualdb is also
incremented.
(4) When the STOP_MEASUREMENT message for the SDCCH channel is
received, if the BTS reports measurement counters, the BSC increments 1601,
1602, 1603, 1622, 1623, 1624, 1625, 1626, 1804, 1805, 1806, 1807 and 1808.
(5) The old (SDCCH) channel is released. 1050 successfulTchFrSeizures is
incremented and, if the MS is the dualband type, 1716
successfulTchFrSeizuresMsDualb is also incremented.
(6) When the old (SDCCH) channel has been released, 1607 counting the average
number of SDCCH used in the inner or outer zone of the cell is decremented.
List of counters incremented or decremented during this procedure:
1107 (1)
1503
1841/1
1094
1095
MODE_MODIFY_REQUEST
CHANNEL_MODE_MODIFY_ACK
CHANNEL_MODE_MODIFY
Reset timer TmodMS
1044
1045 ASSIGNMENT_COMPLETE
1108 (3)
1502
1108
1502 (5)
1107 (1)
1503
1841/0
1616/N
(2)
QUEUEING
1108 (3)
1502 Set timer T11
1616/n(--1)
1618/n(--1)
1744
1746
1609/0
1611/0
1812
1094
1095
CONNECTION_STATE_REQUEST Reset timer T11
Set timer Tcnx
STOP_MEASUREMENT_REQ_ACK
Reset timer T3107
1601 (7)
1602
1603
1622
1623
1624
1625
1626
1805 (8)
1806 (8)
1807 (8)
SABM 1808 (8)
ESTABLISH_INDICATION
UA
ASSIGNMENT_COMPLETE
ASSIGNMENT_COMPLETE
1607 (--1)
RF_CHANNEL RELEASE_ACK Reset timer TrfAck
1607 (--1)
1717
1718
1719
1720
1721
2.4 Handovers
2.4.1 Overview
Each handover procedure performed in a cell requires two phases, a selection phase
and an execution phase.
selection phase: choice of the target cell (outgoing handover) or radio channel
(incoming or intra-bts handover)
execution phase: switchover from one radio channel to another
The execution phase is not started unless the selection phase is successfully
completed as shown in the following diagram.
No No
call interrupted
SELECTION_FAILURE EXECUTION_FAILURE
The ratios between the following counters are used to evaluate the efficiency of the
procedures implemented in the BSS:
Number of handovers required (hoRequiredXxx)
Number of handover requests (hoRequestXxx)
Number of handovers executed (hoExecutionXxx)
Number of successful handovers (hoSuccessXxx)
The procedures call on the following counters in problem cases:
permanent bsc observation:
• hoIndicationNotTreatedTchoke
• hoIndicationNotTreatedTmtBtwHo
• hoUnsuccessReestIntraBts on TCH or SDCCH
• hoUnsuccessReestOutgoingIntraBss on TCH or SDCCH
request
cell N BSS 1 cell A BSS 1 refused
hoRequiredXxx cell N
hoRequestOutgoingIntra cell N
hoRequestIncomingIntra cell N
hoOutIntraFailureXxx cell N
hoInIntraFailureXxx cell A
request
cell N BSS 1 cell B BSS 2 accepted
EXECUTION
successful
hoRequiredXxx cell N
hoRequestOutgoingInter cell N
hoRequestIncomingInter cell B
hoExecutionOutgoingInter cell N
hoExecutionIncomingInter cell B
hoSuccessOutgoingInter cell N
hoSuccessIncomingInter cell B
STOP_MEASUREMENT_REQ_ACK
1198 (3)
1199
1600
1622
1623
1624
1625
1626
1805 (4)
1806 (4)
1807 (4)
1808 (4)
1809/n (4)
UA
ESTABLISHED_INDICATION
ASSIGNMENT_COMPLETE
Reset timer T3107
1083 or
1798 or
1802/n
START_MEASUREMENT_REQUEST
START_MEASUREMENT_REQ_ACK
RF_CHANNEL RELEASE
Set timer TrfAck HANDOVER_PERFORMED
1108
1502 1081 or 1796
1082 or 1797
RF_CHANNEL_RELEASE_ACK
Reset timer TrfAck
1812 (--1) (4)
1746 (--1)
1611 (--1)
(1) A TCH resource is successfully allocated internally in the BSC software on the
target cell. Then the following counters are incremented:
1609/0 tchFrAllocatedTchAllocationTrZone (number of TCH/FR allocated for
traffic in the inner of outer zone of the cell)
1611/0 tchFrAveragedUsedTchAllocationTrZoneMoy/Max/Cum/Ech (average
number of TCH/FR used for traffic in the inner or outer zone of the cell)
1812 allocatedCircuitTsMoy/Max/Cum/Ech (number of TS allocations for
traffic on circuit mode in the cell or
allocatedCircuitTsTrZoneMoy/Max/Cum/Ech (number of TS allocations for
traffic on circuit mode in the inner or the outer of the cell
(2) The counter incremented depends on the channel mode used (speech or data):
either 1197/0 (FR) or 1197/1 (EFR) for speech
1709 and 1705/n (n=0 to 6) for transparent data
1710 and 1707/n (n=0 to 2) for non transparent data
(3) When the STOP_MEASUREMENT message for the TCH channel is received,
if the BTS reports measurement counters, the BSC increments 1198, 1199, 1600,
1622, 1623, 1624, 1625, 1626, 1805, 1806, 1807, 1808 and 1809/n
(4) When the deallocation of TCH is successfully performed in the originating cell,
the following counters are decremented:
1812 allocatedCircuitTsMoy/Max/Cum/Ech (number of TS allocations for
traffic on circuit mode in the cell or
allocatedCircuitTsTrZoneMoy/Max/Cum/Ech (number of TS allocations for
traffic on circuit mode in the inner or the outer of the cell
1746 tchFrAveragedUsedMoy/Max/Cum/Ech (average number of TCH/FR
used in the cell) or tchFrAveragedUsedTrZoneMoy/Max/Cum/Ech (average
number of TCH/FR used in the inner or outer zone of the cell)
1611/0 tchFrAveragedUsedTchAllocationTrZoneMoy/Max/Cum/Ech (average
number of TCH/FR used for traffic in the inner or outer zone of the cell)
List of the counters incremented or decremented during this procedure:
An intra-bss handover request is initiated by the BSC. The MSC is informed of the
change by a HANDOVER PERFORMED message at the end of the procedure.
ASSIGNMENT_REQUEST
1776
1138/n
1744
1746
1609/0 (1)
1611/0 (1)
1812 (1)
CHANNEL_ACTIVATE
Set timer TchnAck
1197/0 or 1197/1
or 1709 and 1705/n (2)
or 1710 and 1707/n
CHANNEL_ACTIVATE_ACK
Reset timer TchnAck
HANDOVER_COMMAND Set timer T3103
STOP_MEASUREMENT_REQUEST
HANDOVER_COMMAND
STOP_MEASUREMENT_REQ_ACK
1198 (1)
1199
1600
1622
1623
1624
1625
1626
1805 (4)
1806 (4)
1807 (4)
1808 (4)
1806/n (4)
HANDOVER_ACCESS
HANDOVER_DETECT
SABM
ESTABLISH_INDICATION
UA
HANDOVER_COMPLETE
1780
1067
1781
1073
1065
1071
1075
1069
1200
1839/n (4)
1840/n (4)
1077
1793, 1794, 1795 and
1208, 1789, 1209 or
START_MEASUREMENT_REQUEST 1783, 1790, 1786 or
1784, 1791, 1787 or
1785, 1792, 1788
START_MEASUREMENT_REQ_ACK
RF_CHANNEL_RELEASE
Set timer TrfAck
1108
1502
RF_CHANNEL_RELEASE_ACK
Reset timer TrfAck
(1) A TCH resource is successfully allocated internally in the BSC software on the
target cell. Then the following counters are incremented:
1609/0 tchFrAllocatedTchAllocationTrZone (number of TCH/FR allocated for
traffic in the inner of outer zone of the cell)
1611/0 tchFrAveragedUsedTchAllocationTrZoneMoy/Max/Cum/Ech (average
number of TCH/FR used for traffic in the inner or outer zone of the cell)
1809/n timingAdvanceAverage for n=0 average timing advance value for the
[n= 0 to 1] or communication in the cell or
timingAdvanceAverageTrZone average timing advance value for the
for n=0 communication in the inner or outer
zone of the cell
timingAdvanceMaximum for maximum timing advance value for
n=1 the communication in the cell or
or maximum timing advance value for
timingAdvanceMaximumTr- the communication in the inner or
Zone for n=1 outer zone of the cell
Data Flow Diagram : inter BSS intra MSC handover procedure (normal completion
with communication on TRAFFIC phase)
The downlink DTAP messages sent by MSC to the target BSC between sending
HANDOVER REQUEST and receiving HANDOVER COMPLETE are ignored.
The uplink DTAP service is not inhibited on the channel being used until the channel
is released.
STOP_MEAS_
REQ_ACK
1198 (3)
1199
1600
1622
1623
1624
1625
1626
1805 (4)
1806 (4)
1807 (4)
1808 (4)
1809/n (4)
PHYSICAL_
INFORMATION
HANDOVER_
DETECT
SABM
ESTABLISH_
INDICATION
UA
START_MEAS_
REQUEST
START_MEAS_
REQ_ACK
1108
1500
HANDOVER_ 1107
COMPLETE 1501
HANDOVER_
COMPLETE
1108
1502
1780
1068
1066
1076
1200
1839/N
1840/N
1078
RF_CHANNEL_
RELEASE
Set timer TrfAck
RF_CHANNEL_
RELEASE_ACK
Reset timer TrfAck 1812 (5)
1746 (5)
1611 (5)
DISCONNECT_
INDICATION
1105 (--1)
(1) The counter incremented depends on the channel mode used (speech or data):
either 1197/0 (FR) or 1197/1 (EFR) for speech
1709 and 1705/n (n=0 to 6) for transparent data
1710 and 1707/n (n=0 to 2) for non transparent data
(2) DTAP is suspended.
(3) When the STOP_MEASUREMENT message for the TCH channel is received,
if the BTS reports measurement counters, the BSC increments 1198, 1199, 1600,
1622, 1623, 1624, 1625, 1626, 1805, 1806, 1807, 1808 and 1809/n
(4) ASCI counters are optional since they are related to the GSM--R functionality.
(5) When the deallocation of TCH is successfully performed in the originating cell,
the following counters are decremented:
1107 (1)
1503
1841/0
1616/n
QUEUEING
1108
1502
1094 Set timer T11
1095 (2)
HANDOVER_INDICATION
(4)
1776
1138/n (5)
Data Flow Diagram: Radio channel release procedure (release indication first with
communication on TRAFFIC phase)
STOP_MEASUREMENT_REQ_ACK
UA
1198
1199
1600
1622
1623
1624
1625
1626
1805 (1)
1806 (1)
1807 (1)
1808 (1)
1809/n (1)
DEACTIVATE_ACK Reset timer TDeacAck
timer T3111
RF_CHANNEL_RELEASE
Timer T3111 expires
Set timer TrfAck
RF_CHANNEL_RELEASE_ACK
Reset timer TrfAck
1607 (--1) DISCONNECT_INDICATION
1105 (--1)
(1) ASCI counters are optional since they are related to the GSM--R functionality.
Data Flow Diagram: Radio channel release procedure (deactivate SACCH Ack with
communication on TRAFFIC phase)
1105 (--1)
(1) ASCI counters are optional since they are related to the GSM--R functionality.
STOP_MEASUREMENT_ACK
1198 (1)
1199
1600
1622
1624
1625
1626
1805
1806
1807
1808
1809/n
DEACTIVATE_SACCH_ACK
Set timer TDeacAck
RELEASE_INDICATION
Set timer TrfAck
DISC
RF_CHANNEL_RELEASE_ACK
Reset timer T3111
1812 (2) DISCONNECT_INDICATION
1746 (3)
1611/0 (4) 1105 (5)
(1) When the STOP_MEASUREMENT message for the TCH channel is received,
if the BTS reports measurement counters, the BSC increments counters 1198, 1499,
1600, 1622, 1623, 1624, 1625, 1626, 1805, 1806, 1807 and 1809/n
(2) 1812 is decremented.
(3)When the deallocation of TCH happens, 1746 is decremented.
(4) 1611 is decremented.
(5)When the release of SCCP connection happens, 1105 is decremented.
List of the counters incremented or decremented during this procedure:
1108
1502
CHANNEL_RELEASE
CHANNEL_RELEASE 1044
1045
DEACTIVATE_SACCH
Set timer TchncAck
STOP_MEASUREMENT
STOP_MEASUREMENT_ACK
1601 (1)
1602
1603
1622
1623
1624
1625
1626
1805
1806
1807
1808
DEACTIVATE_SACCH_ACK
DISC Reset timer TchnAck
RELEASE_INDICATION
UA timer T3111
RF_CHANNEL_RELEASE_ACK
Reset timer TrfAck
DISCONNECT_INDICATION
1607 (--1)
1105 (--1)
CLEAR_COMMAND
Reset timer TclrCMD
1107
1503
1753
1164/20
1095 (--1)
CLEAR_COMPLETE
1108
CHANNEL_RELEASE 1502
CHANNEL_RELEASE
DEACTIVATE_SACCH
Set timer TDeacAck
STOP_MEASUREMENT
DISC
STOP_MEASUREMENT_ACK
UA 1198 (1)
1199
1600
1622
1623
1624
1625
1626
1805
1806
1807
1808
1809/n
DEACTIVATE_SACCH_ACK
Reset timer TDeacAck
RELEASE_INDICATION
Set timer T3111
(1) When the STOP_MEASUREMENT message for the TCH channel is received,
if the BTS report measurement counters, the BSC increments counters 1198, 1199,
1600, 1622, 1623, 1624, 1625, 1626, 1805, 1806, 1807 , 1808 and 1809/n
(2) 1812 is decremented.
(3) When the deallocation of TCH happens, 1746 is decremented.
(4) 1611 is decremented.
(5) When the release of SCCP connection happens, 1105 is decremented.
List of the counters incremented or decremented during this procedure:
1108
CHANNEL_RELEASE 1502
1044
CHANNEL_RELEASE 1045
DEACTIVATE_SACCH
Set timer TchnAck
STOP_MEASUREMENT
DISC
STOP_MEASUREMENT_ACK
UA
1601 (1)
1602
1603
1622
1623
1624
1625
1626
1805
1806
1807
1808
DEACTIVATE_SACCH_ACK
Reset timer TchnAck
RELEASE_INDICATION
Set timer T3111
1105 (--1)
1748
1191/n
1746
1606
1607
CHANNEL_ACTIVATE
Set timer TchnAck
1629
CHANNEL_ACTIVATE_ACK
Reset timer TchnAck
CHANNEL_ACTIVATE
Set timer T3111
IMMEDIAT_ASSIGN
1749
SABM 1192/n
(CM_SERVICE_REQUEST) ESTABLISH_INDICATION
(CM_SERVICE_REQUEST)
UA Reset timer T3111
1750
1193/n
1196 CONNECTION_REQUEST
1108
START_MEASUREMENT_REQUEST 1502
CONNECTION_CONFIRM
START_MEASUREMENT_REQUEST_ACK
DTAP
(CM_SERVICE_ACCEPT)
1107
DTAP (CM_SERVICE_ACCEPT)
1501
CM_SERVICE_ACCEPT
SABM (SAPI 3)
ESTABLISH_INDICATION (SAPI 3)
UA
1621 DTAP (CP_DATA)
DTAP (CP_DATA)
1107
1501
2.7 GPRS
The GPRS procedure described in the following diagram is the normal completion
of the preemption on PDTCH (in the case of Mobile Originating Call).
CHANNEL_REQUIRED
1748
1702
1191/n
1730
1606
1607
1744
1746
1609/2
1611/2
CHANNEL_ACTIVATE
Set timer TchnAck
1629/0
CHANNEL_ACTIVATE_ACK
Reset timer TchnAck
IMMEDIATE_ASSIGNMENT_CMD
Set timer T3101
IMMEDIATE_ASSIGN
1749
SABM 1192/n
(CM_SERVICE_REQUEST)
ESTABLISH_INDICATION Reset timer T3101
UA 1750
1193/n
1195 or 1196
CONNECTION REQUEST (L3 INFORMATION)
1108
1502
CONNECTION_CONFIRM
START_MEASUREMENT_REQUEST
1105
1104/0
START_MEASUREMENT_REQ_ACK
DTAP (AUTHENTIFICATION_REQUIRED)
DATP (AUTH_REQUIRED)
AUTH_REQUIRED 1107
1501
AUTH_RESPONSE
DTAP (AUTH_RESPONSE) DTAP (AUTHENTIFICATION_RESPONSE)
1108
1500
SETUP
SETUP
SETUP
1108
1500 DTAP (CALL_PROCEEDING)
1107
1501
DTAP (CALL_PROCEEDING)
CALL_PROCEEDING
DTAP (ALERTING)
ALERTING
DTAP (ALERTING)
1107
1501
ASSIGNMENT_REQUEST
1107
1503
1841/0
1094
1095
1744
1746
1609/0
1611/0 TDMA_TS_STATUS
TDMA_TS_STATUS_ACK
(1)
1814
1813
CONN_STATE_REQ 1812
CONN_STATE_REQ_ACK
CHANNEL_ACTIVATE_ACK
Reset timer TchnAck
ASSIGNMENT_COMMAND
Set timer T3107
1049
1715
STOP_MEASUREMENT_REQUEST
ASSIGNMENT_COMMAND
STOP_MEASUREMENT_REQ_ACK
1601
1602
1603
1622
1623
1624
1625
1626
1805
1806
1807
SABM 1808
ESTABLISH_INDICATION
UA
1195 or 1196
ASSIGNMENT_COMPLETE
Reset timer T3107
ASSIGNMENT_COMPLETE 1050 ASSIGNMENT_COMPLETE
1716
START_MEASUREMENT_REQUEST 1108
1502
START_MEASUREMENT_REQ_ACK
RF_CHANNEL_RELEASE
1044
1045
RE_CHANNEL_RELEASE_ACK
1607 (--1)
1717
1718
1719
1720
1721 ALERT
CONNECT
CONNECT_ACK
CLEAR_COMMAND
1107
1503
1754
1164/20
1095 (--1)
CLEAR_COMPLETE
CHANNEL_RELEASE 1108
1502
CHANNEL_RELEASE
RELEASE_INDICATION
RF_CHANNEL_RELEASE_ACK
Reset timer TrfAck
1812 (--1)
1746 DISCONNECT_INDICATION
1611 1105 (--1)
TDMA_TS_STATUS
TDMA_TS_STATUS
1813 (--1)
(1) Before sending the TDMA TS STATUS message, the BSC performs the
switching connection between Abis and Agprs interface.
(2) The counter incremented depends on the channel mode used (speech or data):
either 1197/0 (FR) or 1197/1 (EFR) for speech
or 1709 and 1705/n (n=0 to 6) for transparent data
or 1710 and 1707/n (n=0 to 2) for non--transparent data
(3) ASCI counters are optional since they are related to the GSM--R functionality.
List of the counters incremented or decremented during this procedure:
Data Flow Diagram: GPRS procedure (no available resource for a PDTCH
preemption)
TDMA_TS_STATUS
TDMA_TS_STATUS_ACK
1613
(1)
1815
1746 (--1)
1611/0 (--1)
1842/0
1095 (--1)
ASSIGNMENT_FAILURE
1108
1502
ASSIGNMENT_REQUEST
1107
1503
1841/0
1094
1095
1744
1746
1609/0
1611/0 TDMA_TS_STATUS
TDMA_TS_STATUS_ACK (1)
1613
1815
1746 (--1)
1611/0 (--1)
ASSIGNMENT_FAILURE
1842/0
1095 (--1)
1108
1502
CLEAR_COMMAND
1107
1503
1753
1163/20
CLEAR_COMPLETE
1108
1502
1044
1045
CHANNEL_RELEASE
CHANNEL_RELEASE
DEACTIVATE_SACCH
STOP_MEASUREMENT_REQUEST
DISC
STOP_MEASUREMENT_REQ_ACK
UA
1601
1602
1603
1623
1624
1625
1626
1805 (2)
1806 (2)
1807 (2)
1808 (2)
1809/n (2)
REACTIVATE_ACK
RELEASE_INDICATION
DEACTIVATE_SACCH
RF_CHANNEL_RELEASE_ACK
1607 (--1)
(1) When the BSC receives the TDMA TS STATUS NACK message with the error
cause, it aborts the current allocation procedure.
(2) ASCI counters are optional since they are related to the GSM--R functionality.
2.10 PCUSN
MS PCUSN SGSN
LLC_DL_FRAME_MS1
15004/0
15005/0
LLC_DL_FRAME_MS2
15004/0
15005/0
LLC_DL_FRAME_MS3
15004/0
15005/0
BVC_FLOW_CONTROL_REQUESTS
15010/0
BVC_FLOW_CONTROL_ACK
LLC_DL_FRAME_MS4
15004/0
15005/0
LLC_DL_FRAME_MS4
15004/0
15005/0
LLC_DL_FRAME_MS4
15004/0
15005/0
MS4_FLOW_CONTROL_REQUESTS
15010/1
MS4_FLOW_CONTROL_ACK
MS PCUSN SGSN
LLC_DL_FRAME_MS1
15004/0
15005/0
LLC_DL_FRAME_MS1
15004/0
15005/0
LLC_DL_FRAME_MS1
15004/0
15005/0
BSSGP_DISCARDED_PDU
15012/0
15012/1
Data Flow Diagram: Establishment of an UL TBF in two phases access with first
phase in CCCH
MS PCUSN SGSN
CHANNEL_REQUEST
15059/0
IMMEDIATE_ASSIGNMENT
15058/0
PACKET_RESOURCE_REQUEST
15056/1
15047/0
PACKET_UPLINK_ASSIGNMENT
15047/1
PACKET_CONTROL_ACK
15047/0
MS PCUSN SGSN
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK (1)
15049/1
15047/0
15034/0
PACKET_TIMESLOT_RECONFIG
15047/1
PACKET_CONTROL_ACK
15047/0
DL_DATA_BLOCK
15046/1
UL_DATA_BLOCK
15046/0
MS PCUSN SGSN
UL_DATA_BLOCK (1)
15046/0
PACKET_UPLINK_ACK/NACK
15047/1
UL_DATA_BLOCK
15046/0
PACKET_UPLINK_ACK/NACK (2)
15047/1
PACKET_CONTROL_ACK
15033/0
15055/0
15047/0
(1) CV= 0
(2) FAI = 1
MS PCUSN SGSN
UL_DATA_BLOCK
15046/0
PACKET_UPLINK_ACK/NACK (V(Q))
NN0002++
15047/1
UL_DATA_BLOCK
15046/0
UL_DATA_BLOCK
15046/0
PACKET_UPLINK_ACK/NACK (V(Q))
NN0002++
15047/1
UL_DATA_BLOCK
15046/0
UL_DATA_BLOCK
15046/0
PACKET_UPLINK_ACK/NACK (V(Q))
NN0002++
15047/1
UL_DATA_BLOCK
15046/0
UL_DATA_BLOCK
15046/0
PACKET_UPLINK_ACK/NACK (V(Q))
NN0002++=NN0002Max
15057/0
15033/0
15047/1
MS PCUSN SGSN
DL_DATA_BLOCK
15046/1
UL_DATA_BLOCK
15046/0
NN0002++
PACKET_UPLINK_ACK/NACK (V(Q))
15047/1
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK
15046/1
UL_DATA_BLOCK
15046/0
NN0002++
PACKET_UPLINK_ACK/NACK (V(Q))
15047/1
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK
15046/1
UL_DATA_BLOCK
NN0002++
15046/0
PACKET_UPLINK_ACK/NACK (V(Q))
15057/0 NN0002++=NN0002Max
15057/3
15033/0
15033/1
15047/1
This abnormal release occurs when the mobile station does not respond to USF.
Data Flow Diagram: Non response from the mobile station after N3101 scheduled
blocks (means with USF set in downlink)
MS PCUSN SGSN
DL_DATA_BLOCK (USF)
15046/1
UL_DATA_BLOCK
N3101++
DL_DATA_BLOCK (USF)
15046/1
UL_DATA_BLOCK
N3101++
DL_DATA_BLOCK (USF)
15046/1
UL_DATA_BLOCK
N3101++=N3101Max
15033/0
15057/1
15057/2
MS PCUSN SGSN
DL_DATA_BLOCK
15046/1
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK
15046/1
UL_DATA_BLOCK
N3101++
UL_DATA_BLOCK
N3101++
UL_DATA_BLOCK
N3101++=N3101Max
15033/0
15057/1
15057/2
15057/3
15033/1
MS PCUSN SGSN
CHANNEL_REQUEST (RACH)
15059/0
IMMEDIATE_ASSIGNMENT
15058/0
PACKET_RESOURCE_REQUEST
15056/1
15047/0
PACKET_UPLINK_ASSIGNMENT (POLLING)
15047/1
PACKET_CONTROL_ACK
Up_Nassign++
PACKET_UPLINK_ASSIGNMENT (POLLING)
15047/1
PACKET_CONTROL_ACK
Up_Nassign++
PACKET_UPLINK_ASSIGNMENT (POLLING)
15047/1
PACKET_CONTROL_ACK
Up_Nassign++
PACKET_UPLINK_ASSIGNMENT (POLLING)
15047/1
PACKET_CONTROL_ACK
Up_Nassign++
PACKET_UPLINK_ASSIGNMENT (POLLING)
15047/1
PACKET_CONTROL_ACK
Up_Nassign++=Up_NassignMax
15033/0
15057/1
15057/2
15036/0
This abnormal release occurs when the mobile station does not acknowledge uplink
assignment messages.
MS PCUSN SGSN
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK (1)
15047/0
15034/0
PACKET_TIMESLOT_RECONFIG
15047/1
PACKET_CONTROL_ACK
Up_Nassign++
PACKET_TIMESLOT_RECONFIG
15047/1
PACKET_CONTROL_ACK
Up_Nassign++
PACKET_TIMESLOT_RECONFIG
15047/1
PACKET_CONTROL_ACK
Up_Nassign++
PACKET_TIMESLOT_RECONFIG
15047/1
PACKET_CONTROL_ACK
Up_Nassign++
PACKET_TIMESLOT_RECONFIG
15047/1
PACKET_CONTROL_ACK
Up_Nassign++=Up_NassignMax
15033/0
15057/1
15057/2
15033/1
15057/3
MS PCUSN SGSN
UL_DATA_BLOCK (1)
15046/0
PACKET_UPLINK_ACK/NACK (2)
15047/1
UL_DATA_BLOCK
15046/0
PACKET_UPLINK_ACK/NACK (FAI=1)
15047/1
PACKET__CONTROL_ACK
N3103++
PACKET_UPLINK_ACK/NACK (FAI=1)
15047/1
PACKET__CONTROL_ACK
N3103++
PACKET_UPLINK_ACK/NACK (FAI=1)
15047/1
PACKET__CONTROL_ACK
N3103++
PACKET_UPLINK_ACK/NACK (FAI=1)
15047/1
PACKET__CONTROL_ACK
N3103++=N3103Max
15033/0
15057/1
(1) CV= 0
(2) V(Q) <> V(R)
MS PCUSN SGSN
DL_DATA_BLOCK
15046/1
UL_DATA_BLOCK (1)
15046/0
PACKET_UPLINK_ACK/NACK (2)
15047/1
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK
15046/1
PACKET_UPLINK_ACK/NACK (FAI=1)
15047/1
PACKET_CONTROL_ACK
N3103++
PACKET_UPLINK_ACK/NACK (FAI=1)
15047/1
PACKET_CONTROL_ACK
N3103++
PACKET_UPLINK_ACK/NACK (FAI=1)
15047/1
PACKET_CONTROL_ACK
N3103++
PACKET_UPLINK_ACK/NACK (FAI=1)
15047/1
PACKET_CONTROL_ACK
N3103++=N3103Max
15033/0
15057/1
15057/3
15033/1
(1) CV= 0
(2) V(Q) <> V(R)
MS PCUSN SGSN
PAGING
CHANNEL_REQUEST (RACH)
15059/0
IMMEDIATE_ASSIGNMENT
15058/0
PACKET_RESOURCE_REQUEST
15056/1
15047/0
PACKET_UPLINK_ASSIGNMENT
15047/1
PACKET_CONTROL_ACK
15047/1
15046/0 LLC_UL_FRAME
PACKET_CONTROL_ACK
15047/0
PACKET_UPLINK_ACK/NACK (1)
15047/1
PACKET_CONTROL_ACK
15047/1
DL_DATA_BLOCK
15046/1 LLC_DL_FRAME
15004/0
15005/0
15031/1
(1) Downlink pre--establishment
(2) FAI = 1
For a mobile station in Standby State, the network may initiate the paging procedure
for downlink packet transfer in order to obtain the mobile station cell location for
the downlink packet transfer. The mobile station performs a page response by
sending and LLC PDU to the network.
MS PCUSN SGSN
LLC_DL_FRAME
IMMEDIATE_ASSIGNMENT 15004/0
15005/0
15058/2 15031/1
DL_DATA_BLOCK (1)
15046/1
PACKET_POLLING_REQUEST
15047/1
PACKET_CONTROL_ACK
15047/0
PACKET_POWER_CONTROL_TIMING_
ADVANCE
15047/1
PACKET_DOWNLINK_ACK/NACK
15047/0
PACKET_DOWNLINK_ASSIGNMENT
15047/1
PACKET_CONTROL_ACK
15047/0
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK
15046/1
MS PCUSN SGSN
UL_DATA_BLOCK
15046/1
UL_DATA_BLOCK
15046/1 LLC_DL_FRAME
PACKET_TIMESLOT_RECONFIGURE 15004/0
15005/0
15047/1 15031/1
PACKET_CONTROL_ACK
15047/0
DL_DATA_BLOCK
15046/1
MS PCUSN SGSN
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK (1)
15046/1
PACKET_DOWNLINK_ACK/NACK (2)
15033/1
15047/0
15055/1
MS PCUSN SGSN
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK (V(A))
N0002++
15047/0
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK (V(A))
N0002++
15047/0
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK (V(A))
N0002++=NN0002Max
15047/0
15057/0
15033/1
MS PCUSN SGSN
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK (V(A))
N0002++
15047/0
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK
15046/1
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK (V(A))
N0002++
15047/0
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK (V(A))
N0002++=NN0002Max
15047/0
15057/0
15057/1
15033/1
15033/0
MS PCUSN SGSN
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK (V(A))
15047/0
DL_DATA_BLOCK
15046/1
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK
N3105++
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK
N3105++
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK
N3105++
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK
N3105++=N3105Max
15033/1
15057/3
MS PCUSN SGSN
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK
15047/0
DL_DATA_BLOCK
15046/1
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK
N3105++
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK
N3105++
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK
N3105++
DL_DATA_BLOCK (POLLING)
15046/1
PACKET_DOWNLINK_ACK/NACK
N3105++=N3105Max
15033/1
15057/3
15057/1
15033/0
MS PCUSN SGSN
PACKET_DOWNLINK_ASSIGNMENT
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++
PACKET_DOWNLINK_ASSIGNMENT
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++
PACKET_DOWNLINK_ASSIGNMENT
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++
PACKET_DOWNLINK_ASSIGNMENT
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++
PACKET_DOWNLINK_ASSIGNMENT
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++=Dn_NassignMax
15033/1
15057/3
This abnormal release occurs when the mobile station does not acknowledge
downlink assignment messages.
Data Flow Diagram: Non response from the mobile after DN_NASSIGNMAX
Packet Downlink Assignment messages during full duplex transfer, in the case that
the DL TBF is also released.
MS PCUSN SGSN
UL_DATA_BLOCK
15046/0
PACKET_UPLINK_ACK/NACK
15049/0
PACKET_TIMESLOT_RECONFIG
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++
PACKET_TIMESLOT_RECONFIG
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++
PACKET_TIMESLOT_RECONFIG
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++
PACKET_TIMESLOT_RECONFIG
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++
PACKET_TIMESLOT_RECONFIG
(POLLING)
15047/1
PACKET_CONTROL_ACK
Dn_Nassign++=Dn_NassignMax
15033/1
15057/3
15057/1
15033/0
MS PCUSN SGSN
DL_DATA_BLOCK (1)
15046/1
PACKET_DOWNLINK_ACK/NACK
NN0002++
DL_DATA_BLOCK (1)
15046/1
PACKET_DOWNLINK_ACK/NACK
NN0002++
DL_DATA_BLOCK (1)
15046/1
PACKET_DOWNLINK_ACK/NACK
NN0002++
DL_DATA_BLOCK (1)
15046/1
PACKET_DOWNLINK_ACK/NACK
NN0002++=NN0002Max
15057/4
15057/0
15033/1
This abnormal release occurs when the mobile station does not acknowledge the last
downlink data block (sent with FBI=1 and S/P=1).
Data Flow Diagram: there is no response from the mobile after NN0002 downlink
data blocks sent with FBI=1 and S/P=1 during full duplex transfer, in the case that
the UL TBF is also released.
MS PCUSN SGSN
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK (1)
15046/1
PACKET_DOWNLINK_ACK/NACK
NN0002++
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK (1)
15046/1
PACKET_DOWNLINK_ACK/NACK
NN0002++
UL_DATA_BLOCK
15046/0
DL_DATA_BLOCK (1)
15046/1
PACKET_DOWNLINK_ACK/NACK
NN0002++
DL_DATA_BLOCK (1)
15046/1
PACKET_DOWNLINK_ACK/NACK
NN0002++=NN0002Max
15057/3
15057/4
15057/1
15033/1
15033/0
15046/0
CHANNEL_
REQUEST
PCU_TDMA_TS_STATUS
PCU_TDMA_TS_STATUS_
NACK
1815
PCU_TDMA_TS_STATUS
PACKET_PDTCH_RELEASE
PACKET_PDTCH_RELEASE
PACKET_PDTCH_RELEASE
PCU_TDMA_TS_STATUS_
ACK
1814 BVC_FLOW_CONTROL_
REQUESTS
15010/0
BVC_FLOW_CONTROL_ACK
15046/0
CHANNEL_REQUEST
15059/0
DL_DATA_BLOCK
15046/1
IMMEDIATE_ASSIGNMENT
15058/0
PACKET_RESOURCE_REQUEST
15056/1
15047/0
PACKET_UPLINK_ASSIGNMENT
15047/1
PACKET_CONTROL_ACK
15047/0
UL_DATA_BLOCK
15046/0 LLC_UL_FRAME
15004/1
15005/1
FLUSH_LL_BTS--A
15014/0
FLUSH_LL_ACK
channel_activate (SDCCH)
channel_activate_ack
imm_ass imm_ass_command
2036 (8W)
CM_serv_acc
channel_activate_ack
assignment_command
SABM est_ind
UA
assignment_comp
assignment_comp
2037 (8W) RF_channel_release(SDCCH)
RF_channel_release_ack
SCCP_CC
VGCS/VBS_setup_ack
notification/NCH
(cyclic notification process)
Data Flow Diagram: Standard call termination (the originator releases the VBS/
VGCS call)
termination_request
termination
clear_command
channel_release
deactivate_SACCH
deactivate_SACCH_ack
DISC
Release_indication
2053 (8W)
RF_channel_release(SDCCH)
RF_channel_release_ack
clear_complete
SCCP_RLSD
Notification_command clear_command
UI(channel_release) Channel_release clear_complete
UI(channel_release) SCCP_RLSD
UI(channel_release)
Deactivate_SACCH
Deactivate_SACCH_ack
RF_channel_release
RF_channel_release_ack
BSC type
Observation type BSC BSC 3000
12000HC
OGS X X
OFS X X
ORT X X
Temporary Interference X
Temporary Abis Interface X
Temporary SS7 Link X
ODIAG X X
COUNTER TYPE
COUNTER IDENTIFIER
SCREENING CRITERIA
CUMULATED VALUE
CUMULATED VALUE
NUMBER OF SAMPLES
MAX VALUE (if required)
CUMULATED VALUE
NUMBER OF SAMPLES
MAX VALUE (if required)
MIN/MAX FLAG
Two major constraints must be taken into account when running observations:
the number of counter Ids per observation type
a threshold related to the use of BSC memory
Name Meaning
CUM_CELL number of screenings (couple id:subid) of
cumulative counters belonging to CELL
location and OFS, OGS and ORT
observations
CUM_CELL_ODIAG number of screenings (couple id:subid) of
cumulative counters belonging to CELL
location and ODIAG observation
VAL_CELL number of screenings (couple id:subid) of
value counters belonging to CELL location
and OFS, OGS and ORT observations
VAL_CELL_ODIAG number of screenings (couple id:subid) of
value counters belonging to CELL location
and ODIAG observation
LOAD_CELL number of screenings (couple id:subid) of
load counter belonging to CELL location and
OFS, OGS and ORT observations
LOAD_CELL_ODIAG number of screenings (couple id:subid) of
load counter belonging to CELL location and
ODIAG observation
CUM_TDMA_class number of screenings (couple id:subid) of
cumulative counters belonging to TDMA
class location and OFS, OGS and ORT
observations
CAUTION
GSM--R specific
“Toggling” counters provide the operator with statistics indexed by the MS power
class (2 W or 8 W or 2 W + 8 W).
The QoS is measured by type of application:
train control with 8 W mobiles, and with a high QoS
shunt with 2 W mobiles, and with a lower QoS
The operator can toggle between ignoring/taking into account the power class
criterium at the OMC-R. The incrementation of “toggling” counters depends on the
value of the msPowerClassToggle parameter (settable by the operator on the bts
object at the OMC--R). The default value of the msPowerClassToggle parameter is
“2W + 8W”. The operator can set it either to “2W” or to “8W”.
Note: A synthetic counter can be used as a “toggling” counter only if all the
counters that are part of the formula are “toggling” counters themselves.
Hence, if one counter is not a “toggling” counter, then the synthetic counter
is valid only if the msPowerClassToggle parameter is set to “2W + 8W”.
GPRS
GPRS on TrZone
Inter--bss handovers
Interferences
Intra--bss handovers
Intra--cell handovers
Layer One Management
Layer One Management on TrZone
Neighbor cells
OMC interface
PCM
Releases of communications in signalling phase
Releases of communications in traffic phase
SDCCH allocations on TrZone
SMS
TCH allocations
TCH allocations on TrZone
WPS
The permanent general observation covers the following counter classes:
general statistic observation (OGS) counters
fast statistic observation (OFS) counters
real time observation (ORT) counters
diagnostic observation (ODIAG) counters
4.1.3 A interface
Counter No. Q3 Name Type
1094/0 tcAllocated totalizer
1095/0 tcAveragedUsedMoy load
1095/0 tcAveragedUsedMax load
1095/0 tcAveragedUsedCum load
1095/0 tcAveragedUsedEch load
1104/0 sccpAllocated totalizer
1104/1 sccpAllocatedLcs totalizer
1105/0 sccpAveragedUsedMoy load
1105/0 sccpAveragedUsedMax load
1105/0 sccpAveragedUsedCum load
1105/0 sccpAveragedUsedEch load
1106/0 sccpRessourceFailure totalizer
1106/1 sccpRessourceFailureBscRefusal totalizer
4.1.4 AMR
Counter No. Q3 Name Type
1903/0 amrFrTchSuccessfullyAssigned totalizer
1903/1 amrHrTchSuccessfullyAssigned totalizer
1904/0 amrFrTchAssignFailure totalizer
1904/1 amrHrTchAssignFailure totalizer
1906/0 downlinkPowerCtrlMaxTchAmrFrCum value
1906/0 downlinkPowerCtrlMaxTchAmrFrEch value
1906/0 downlinkPowerCtrlMaxTchAmrFrMoy value
1906/0 downlinkPowerCtrlMaxTchAmrFrMax value
1907/0 uplinkPowerCtrlMaxTchAmrFrCum value
1907/0 uplinkPowerCtrlMaxTchAmrFrEch value
1907/0 uplinkPowerCtrlMaxTchAmrFrMoy value
1907/0 uplinkPowerCtrlMaxTchAmrFrMax value
1912/0 msPowerIncControlAmrFr totalizer
1913/0 msPowerDecControlAmrFr totalizer
1914/0 bsPowerIncControlAmrFr totalizer
1915/0 bsPowerDecControlAmrFr totalizer
1917/0 timingAdvanceAmrFrAvg totalizer
1917/1 timingAdvanceAmrFrMax totalizer
1918/0 downlinkPowerCtrlMaxTchAmrHrCum value
4.1.6 ASCI
Counter No. Q3 Name Type
1193/8 estabIndicSignallingPiggybacked totalizer
1504/0 vgcsAccessGrant totalizer
1505/0 vgcsMscReject totalizer
4.1.7 BSC
Counter No. Q3 Name Type
1121/0 chainStandByUpdate totalizer
1122/0 chainStandByResponse totalizer
1506/0 aintOverloadRejectedOpPageReq totalizer
1506/1 aintOverloadRejectedOpIncomingExtHoReq totalizer
1506/4 aintOverLoadRejectedOpPerformLocationReq totalizer
1803/0 cgOverloadRejectedOpPageReqCg0 totalizer
1803/0 cgOverloadRejectedOpPageReqCg1 totalizer
1803/0 cgOverloadRejectedOpPageReqCg2 totalizer
1803/1 cgOverloadRejectedOpChannelReqCg0 totalizer
1803/1 cgOverloadRejectedOpChannelReqCg1 totalizer
1803/1 cgOverloadRejectedOpChannelReqCg2 totalizer
1803/2 cgOverloadRejectedOpEstablishIndCg0 totalizer
1803/2 cgOverloadRejectedOpEstablishIndCg1 totalizer
1803/2 cgOverloadRejectedOpEstablishIndCg2 totalizer
1803/3 cgOverloadRejectedOpHoReqCg0 totalizer
1803/3 cgOverloadRejectedOpHoReqCg1 totalizer
1803/3 cgOverloadRejectedOpHoReqCg2 totalizer
1803/4 cgOverloadRejectedOpPageReqBtsCg0 totalizer
1803/4 cgOverloadRejectedOpPageReqBtsCg1 totalizer
1803/4 cgOverloadRejectedOpPageReqBtsCg2 totalizer
1803/5 cgOverloadRejectedOpSmsCbCg0 totalizer
1803/5 cgOverloadRejectedOpSmsCbCg1 totalizer
1803/5 cgOverloadRejectedOpSmsCbCg2 totalizer
1834/0 lapdOverloadRejectedOpSicd0 totalizer
4.1.8 BSC 3G
Counter No. Q3 Name Type
1507/0 e3OverloadRejectedOpPagingReq totalizer
1507/1 e3OverloadRejectedOpChannelReq totalizer
1507/2 e3OverloadRejectedOpEstablishInd totalizer
1507/3 e3OverloadRejectedOpHoReq totalizer
1507/4 e3OverloadRejectedOpPagingReqReject totalizer
1507/5 e3OverloadRejectedOpSmsCb totalizer
1508/0 pagingFilteredByBsc totalizer
3000/0 prLoadCne3OmuSbcMoy load
3000/0 prLoadCne3OmuSbcMax load
3000/0 prLoadCne3OmuSbcCum load
3000/0 prLoadCne3OmuSbcEch load
3001/0 prLoadCne3TmuSbcMoy load
3001/0 prLoadCne3TmuSbcMax load
3001/0 prLoadCne3TmuSbcCum load
3001/0 prLoadCne3TmuSbcEch load
3001/2 prLoadCne3TmuPmcMoy load
3001/2 prLoadCne3TmuPmcMax load
3001/2 prLoadCne3TmuPmcCum load
3001/2 prLoadCne3TmuPmcEch load
3004/0 e3PrMemCnOmuSbcMemCum value
3004/0 e3PrMemCnOmuSbcMemEch value
4.1.14 EDGE
Counter No. Q3 Name Type
1163/33 signallingReleaseCellTbcEdge totalizer
1164/33 trafficReleaseTbcEdge totalizer
2000/0 totalNumberOfEdgeTsMoy load
2000/0 totalNumberOfEdgeTsMax load
2000/0 totalNumberOfEdgeTsCum load
2000/0 totalNumberOfEdgeTsEch load
2000/0 totalNumberOfEdgeTsTrZoneMoy load
2000/0 totalNumberOfEdgeTsTrZoneMax load
2000/0 totalNumberOfEdgeTsTrZoneCum load
2000/0 totalNumberOfEdgeTsTrZoneEch load
2000/1 allocatedEdgeTsMoy load
2000/1 allocatedEdgeTsMax load
2000/1 allocatedEdgeTsCum load
2000/1 allocatedEdgeTsEch load
2000/1 allocatedEdgeTsTrZoneMoy load
2000/1 allocatedEdgeTsTrZoneMax load
2000/1 allocatedEdgeTsTrZoneCum load
2000/1 allocatedEdgeTsTrZoneEch load
2000/2 preemptedEdgeTsMoy load
2000/2 preemptedEdgeTsMax load
2000/2 preemptedEdgeTsCum load
2000/2 preemptedEdgeTsEch load
2000/2 preemptedEdgeTsTrZoneMoy load
2000/2 preemptedEdgeTsTrZoneMax load
2000/2 preemptedEdgeTsTrZoneCum load
2000/2 preemptedEdgeTsTrZoneEch load
2001/0 allocatedAbisJokerTSEdgeMoy load
4.1.15 Establishment
Counter No. Q3 Name Type
1191/0 channelRequestCause000 totalizer
1191/1 channelRequestCause001 totalizer
1191/2 channelRequestCause010 totalizer
1191/3 channelRequestCause011 totalizer
1191/4 channelRequestCause100 totalizer
1191/5 channelRequestCause101 totalizer
1191/6 channelRequestCause110 totalizer
4.1.17 GPRS
Counter No. Q3 Name Type
1086/0 gprsRachRejectedSicd0 totalizer
1086/0 gprsRachRejectedSicd1 totalizer
1086/0 gprsRachRejectedSicd2 totalizer
1086/0 gprsRachRejectedSicd3 totalizer
1086/0 gprsRachRejectedSicd4 totalizer
1086/0 gprsRachRejectedSicd5 totalizer
1086/0 gprsRachRejectedSicd6 totalizer
1086/0 gprsRachRejectedSicd7 totalizer
1086/0 gprsRachRejectedSicd8 totalizer
1086/0 gprsRachRejectedSicd9 totalizer
1087/0 gprsImmAssRejectedSicd0 totalizer
1087/0 gprsImmAssRejectedSicd1 totalizer
1087/0 gprsImmAssRejectedSicd2 totalizer
1087/0 gprsImmAssRejectedSicd3 totalizer
1087/0 gprsImmAssRejectedSicd4 totalizer
1087/0 gprsImmAssRejectedSicd5 totalizer
1087/0 gprsImmAssRejectedSicd6 totalizer
1087/0 gprsImmAssRejectedSicd7 totalizer
1087/0 gprsImmAssRejectedSicd8 totalizer
4.1.20 Interferences
Counter No. Q3 Name Type
1619/0 channelAveragedIdlePerInterfBand0Cum value
4.1.27 PCM
Counter No. Q3 Name Type
1114/0 pcmUnavailabilityCum value
1114/0 pcmUnavailabilityEch value
1114/0 pcmUnavailabilityMoy value
1114/0 pcmUnavailabilityMax value
1755/0 pcmFaultExternal totalizer
1755/1 pcmFaultInternal totalizer
1755/2 pcmFaultDDTIBoard totalizer
1755/3 pcmFaultOutOfService totalizer
4.1.31 SMS
Counter No. Q3 Name Type
1621/0 sapi3SessionEstablishment totalizer
4.1.34 WPS
Counter No. Q3 Name Type
1609/3 tchFrAllocatedWps totalizer
1609/3 tchFrAllocatedWpsTrZone totalizer
1610/1 tchHrAllocatedWps totalizer
1610/1 tchHrAllocatedWpsTrZone totalizer
1026/0 rachBusyCount/Ts2/Ts4/Ts6 - Y Y -
1027/0 rachAccessCount/Ts2/Ts4/Ts6 - Y Y -
1028/0 pchNoWait/Ts2/Ts4/Ts6 - Y Y -
1029/0 pchOneWait/Ts2/Ts4/Ts6 - Y Y -
1030/0 pchTwoWait/Ts2/Ts4/Ts6 - Y Y -
1031/0 pchMoreWait/Ts2/Ts4/Ts6 - Y Y -
1033/0 rachNonDecodedAvLevel[Cum,Ech,Moy,Max] - Y Y -
1033/0 rachNonDecodedAvLevelTs2[Cum,Ech,Moy,Max] - Y Y -
1033/0 rachNonDecodedAvLevelTs4[Cum,Ech,Moy,Max] - Y Y -
1033/0 rachNonDecodedAvLevelTs6[Cum,Ech,Moy,Max] - Y Y -
1044/0 signallingPhaseDuration[Cum,Ech,Moy,Max] - Y Y -
1045/0 signallingPhaseDurationHigh[Cum,Ech,Moy,Max] - Y Y -
1049/0 attemptedTchFrSeizures - Y Y -
1050/0 successfulTchFrSeizures - Y Y -
1055/0 assignFailure - Y Y -
1057/0 allTchFrAllocatedTime[Cum,Ech,Moy,Max] - Y Y -
1057/0 allTchFrAllocatedTimeTrZone[Cum,Ech,Moy,Max] - Y Y -
1060/0 allSdcchAllocatedTime[Cum,Ech,Moy,Max] - Y Y -
1060/0 allSdcchAllocatedTimeTrZone[Cum,Ech,Moy,Max] - Y Y -
1065/0 hoExecutionOutgoingIntraBss - Y Y -
1065/1 hoExecutionOutgoingIntraBssForDirectedRetry - Y Y -
1066/0 hoExecutionOutgoingInterBss - Y Y -
1066/1 hoExecutionOutgoingInterBssForDirectedRetry - Y Y -
1067/0 hoSuccessOutgoingIntraBss - Y Y -
1067/1 hoSuccessOutgoingIntraBssForDirectedRetry - Y Y -
1068/0 hoSuccessOutgoingInterBss - Y Y -
1068/1 hoSuccessOutgoingInterBssForDirectedRetry - Y Y -
1069/0 hoRequestIncomingIntraBss Y Y Y -
1070/0 hoRequestIncomingInterBss Y Y Y -
1071/0 hoExecutionIncomingIntraBss - Y Y -
1072/0 hoExecutionIncomingInterBss - Y Y -
1073/0 hoSuccessIncomingIntraBss - Y Y -
1074/0 hoSuccessIncomingInterBss - Y Y -
1075/0 hoRequestOutgoingIntraBss - Y Y -
1076/0 hoRequestOutgoingInterBss - Y Y -
1077/0 hoSuccessOutgoingFirstIntra - Y Y -
1078/0 hoSuccessOutgoingFirstInter - Y Y -
1081/0 hoRequestIntraBts - Y Y -
1082/0 hoExecutionIntraBts - Y Y -
1083/0 hoSuccessIntraBts - Y Y -
1084/0 abisLevel1ErrorsBadFrame[00..17] N N Y N
1084/0 abisLevel1ErrorsBadFrame[20..27] N N Y N
1084/0 abisLevel1ErrorsBadFrame[30..37] N N Y N
1084/0 abisLevel1ErrorsBadFrame[40..47] N N Y N
1084/0 abisLevel1ErrorsBadFrame[50..53] N N Y N
1084/0 abisLevel1ErrorsBadFrame[60..63] N N Y N
1084/0 abisLevel1ErrorsBadFrame[70..73] N N Y N
1084/0 abisLevel1ErrorsBadFrame[80..83] N N Y N
1084/0 abisLevel1ErrorsBadFrame[90..93] N N Y N
1084/3 abisLevel1ErrorsCrcError[00..07] N N Y N
1084/3 abisLevel1ErrorsCrcError[10..17] N N Y N
1084/3 abisLevel1ErrorsCrcError[20..27] N N Y N
1084/3 abisLevel1ErrorsCrcError[30..37] N N Y N
1084/3 abisLevel1ErrorsCrcError[40..47] N N Y N
1084/3 abisLevel1ErrorsCrcError[50..53] N N Y N
1084/3 abisLevel1ErrorsCrcError[60..63] N N Y N
1084/3 abisLevel1ErrorsCrcError[70..73] N N Y N
1084/3 abisLevel1ErrorsCrcError[80..83] N N Y N
1084/3 abisLevel1ErrorsCrcError[90..93] N N Y N
1084/4 abisLevel1ErrorsLostAlign[00..07] N N Y N
1084/4 abisLevel1ErrorsLostAlign[10..17] N N Y N
1084/4 abisLevel1ErrorsLostAlign[20..27] N N Y N
1084/4 abisLevel1ErrorsLostAlign[30..37] N N Y N
1084/4 abisLevel1ErrorsLostAlign[40..47] N N Y N
1084/4 abisLevel1ErrorsLostAlign[50..53] N N Y N
1084/4 abisLevel1ErrorsLostAlign[60..63] N N Y N
1084/4 abisLevel1ErrorsLostAlign[70..73] N N Y N
1084/4 abisLevel1ErrorsLostAlign[80..83] N N Y N
1084/4 abisLevel1ErrorsLostAlign[90..93] N N Y N
1086/0 gprsRachRejectedSicd[0..9] - - - -
1087/0 gprsImmAssRejectedSicd[0..9] - - - -
1088/0 gprsPagingRejectedSicd[0..9] - - - -
1094/0 tcAllocated - Y Y -
1095/0 tcAveragedUsed[Moy,Max,Cum,Ech] Y Y Y Y
1104/0 sccpAllocated - Y Y -
1104/1 sccpAllocatedLcs - Y Y -
1105/0 sccpAveragedUsed[Moy,Max,Cum,Ech] Y Y Y -
1106/0 sccpRessourceFailure - Y Y -
1106/1 sccpRessourceFailureBscRefusal - Y Y -
1106/2 sccpRessourceFailureLcs - Y Y -
1106/3 sccpRessourceFailureBscRefusalLcs - Y Y -
1107/0 aInputMessage Y Y Y -
1108/0 aOutputMessage Y Y Y -
1109/0 aMessageErrors - Y Y -
1114/0 pcmUnavailability[Cum,Ech,Moy,Max] - Y Y -
1115/0 omcLinkSwitchOver - Y Y -
1121/0 chainStandByUpdate N N N Y
1122/0 chainStandByResponse N N N Y
1134/0 hoUnsuccessReestIntraBtsTch - Y Y -
1135/0 hoUnsuccessReestOutgoingIntraBssTch - Y Y -
1136/0 hoUnsuccessReestOutgoingInterBssTch - Y Y -
1137/0 hoUnsuccessReestIncomingIntraBssTch - Y Y -
1138/0 hoRequiredTchUplinkStrength - Y Y -
1138/1 hoRequiredTchDownlinkStrength - Y Y -
1138/10 hoRequiredTchDirectedRetry - Y Y -
1138/11 hoRequiredTchTdmaClass0 - Y Y -
1138/12 hoRequiredTchTdmaClass1 - Y Y -
1138/13 hoRequiredTchInterBtsOm - Y Y -
1138/14 hoRequiredTchTraffic - Y Y -
1138/15 hoRequiredTchTieringLargeToSmallPattern - Y Y -
1138/16 hoRequiredTchTieringSmallToLargePattern - Y Y -
1138/2 hoRequiredTchUplinkQuality - Y Y -
1138/3 hoRequiredTchDownlinkQuality - Y Y -
1138/4 hoRequiredTchDistance - Y Y -
1138/5 hoRequiredTchPowerBudgetQuality - Y Y -
1138/6 hoRequiredTchCapture - Y Y -
1138/7 hoRequiredTchIntraBtsOm - Y Y -
1138/8 hoRequiredTchIntraBtsUplink - Y Y -
1138/9 hoRequiredTchIntraBtsDownlink - Y Y -
1139/0 hoRequiredSdcchUplinkStrength - Y - Y
1139/1 hoRequiredSdcchDownlinkStrength - Y - Y
1139/13 hoRequiredSdcchInterBtsOm - Y - Y
1139/14 hoRequiredSdcchTraffic - Y - Y
1139/2 hoRequiredSdcchUplinkQuality - Y - Y
1139/3 hoRequiredSdcchDownlinkQuality - Y - Y
1139/4 hoRequiredSdcchDistance - Y - Y
1139/5 hoRequiredSdcchPowerBudget - Y - Y
1139/6 hoRequiredSdcchCapture - Y - Y
1139/7 hoRequiredSdcchIntraBtsOm - Y - Y
1139/8 hoRequiredSdcchIntraBtsUplink - Y - Y
1139/9 hoRequiredSdcchIntraBtsDownlink - Y - Y
1140/0 hoExecutionOutgoingIntraBssSdcch - Y - Y
1141/0 hoExecutionOutgoingInterBssSdcch - Y - Y
1142/0 hoSuccessOutgoingIntraBssSdcch - Y - Y
1143/0 hoSuccessOutgoingInterBssSdcch - Y - Y
1144/0 hoRequestIncomingIntraBssSdcch - Y - Y
1145/0 hoRequestIncomingInterBssSdcch - Y - Y
1146/0 hoExecutionIncomingIntraBssSdcch - Y - Y
1147/0 hoExecutionIncomingInterBssSdcch - Y - Y
1148/0 hoSuccessIncomingIntraBssSdcch - Y - Y
1149/0 hoSuccessIncomingInterBssSdcch - Y - Y
1150/0 hoRequestOutgoingIntraBssSdcch - Y - Y
1151/0 hoRequestOutgoingInterBssSdcch - Y - Y
1152/0 hoSuccessOutgoingFirstIntraSdcch - Y - Y
1153/0 hoSuccessOutgoingFirstInterSdcch - Y - Y
1154/0 hoRequestIntraBtsSdcch - Y - Y
1155/0 hoExecutionIntraBtsSdcch - Y - Y
1156/0 hoSuccessIntraBtsSdcch - Y - Y
1157/0 hoUnsuccessReestIntraBtsSdcch - Y - Y
1158/0 hoUnsuccessReestOutgoingIntraBssSdcch - Y - Y
1159/0 hoUnsuccessReestOutgoingInterBssSdcch - Y - Y
1160/0 hoUnsuccessReestIncomingIntraBssSdcch - Y - Y
1161/0 immediateAssignmentRejectTraffMsc - Y Y -
1161/1 immediateAssignmentRejectRadioRes - Y Y -
1161/2 immediateAssignmentRejectChanActNack - Y Y -
1161/3 immediateAssignmentRejectChanActTimmack - Y Y -
1161/5 immediateAssignmentRejectOverload - Y Y -
1161/6 immediateAssignmentRejectTimingAdv - Y Y -
1161/7 immediateAssignmentRejectOthers - Y Y -
1162/0 signallingReleaseNoBtsSccpDiscInd - Y Y -
1162/1 signallingReleaseNoBtsReset - Y Y -
1162/26 signallingReleaseNoBtsTsccRel - Y Y -
1162/27 signallingReleaseNoBtsBadDataInd - Y Y -
1162/28 signallingReleaseNoBtsOthers - Y Y -
1162/3 signallingReleaseNoBtsSccpDataRefusal - Y Y -
1163/0 signallingReleaseBtsSccpDiscInd - Y Y -
1163/1 signallingReleaseBtsReset - Y Y -
1163/10 signallingReleaseBtsCicRemovalEqptFail - Y Y -
1163/11 signallingReleaseBtsOmRadioChanBloc - Y Y -
1163/12 signallingReleaseBtsCallClearing - Y Y -
1163/13 signallingReleaseBtsCnxFailRadioIntFail - Y Y -
1163/14 signallingReleaseBtsCnxFailRadioLinkFail - Y Y -
1163/16 signallingReleaseBtsReleaseInd - Y Y -
1163/17 signallingReleaseBtsErrorIndT200 - Y Y -
1163/18 signallingReleaseBtsErrorIndDm - Y Y -
1163/19 signallingReleaseBtsErrorIndSeq - Y Y -
1163/2 signallingReleaseBtsResetCirc - Y Y -
1163/20 signallingReleaseBtsClearCommand - Y Y -
1163/21 signallingReleaseBtsRfResInd - Y Y -
1163/22 signallingReleaseBtsSwitchOver - Y Y -
1163/23 signallingReleaseBtsTmodMs - Y Y -
1163/24 signallingReleaseBtsT3103 - Y Y -
1163/25 signallingReleaseBtsT8 - Y Y -
1163/28 signallingReleaseBtsOthers - Y Y -
1163/3 signallingReleaseBtsSccpDataRefusal - Y Y -
1163/30 signallingReleaseBtsT11 - Y Y -
1163/32 signallingReleaseBtsCnxFailRemTransFail - Y Y -
1163/33 signallingReleaseCellTbcEdge - Y Y -
1163/4 signallingReleaseBtsIncFirstL3 - Y Y -
1163/5 signallingReleaseBtsT3101 - Y Y -
1163/6 signallingReleaseBtsT3107CircDown - Y Y -
1163/7 signallingReleaseBtsOmTsRemoval - Y Y -
1163/8 signallingReleaseBtsTsRemovalEqptFail - Y Y -
1163/9 signallingReleaseBtsOmCicRemoval - Y Y -
1164/0 trafficReleaseSccpDiscInd - Y Y -
1164/1 trafficReleaseReset - Y Y -
1164/10 trafficReleaseCicRemovalEqptFail - Y Y -
1164/11 trafficReleaseOmRadioChanBloc - Y Y -
1164/12 trafficReleaseCallClearing - Y Y -
1164/13 trafficReleaseCnxFailRadioIntFail - Y Y -
1164/14 trafficReleaseCnxFailRadioLinkFail - Y Y -
1164/16 trafficReleaseReleaseInd - Y Y -
1164/17 trafficReleaseErrorIndT200 - Y Y -
1164/18 trafficReleaseErrorIndDm - Y Y -
1164/19 trafficReleaseErrorIndSeq - Y Y -
1164/2 trafficReleaseResetCirc - Y Y -
1164/20 trafficReleaseClearCommand - Y Y -
1164/21 trafficReleaseRfResInd - Y Y -
1164/23 trafficReleaseTmodMs - Y Y -
1164/24 trafficReleaseT3103 - Y Y -
1164/25 trafficReleaseT8 - Y Y -
1164/28 trafficReleaseOthers - Y Y -
1164/3 trafficReleaseSccpDataRefusal - Y Y -
1164/31 trafficReleaseSysInfoFail - Y Y -
1164/32 trafficReleaseCnxFailRemTransFail - Y Y -
1164/33 trafficReleaseTbcEdge - Y Y -
1164/6 trafficReleaseT3107CircDown - Y Y -
1164/7 trafficReleaseOmTsRemoval - Y Y -
1164/8 trafficReleaseTsRemovalEqptFail - Y Y -
1164/9 trafficReleaseOmCicRemoval - Y Y -
1165/0 hoIndicationNotTreatedTchoke - Y Y -
1167/0 hoUnsuccessOutgoingIntraBssNAttemptTch - Y Y -
1168/0 hoUnsuccessOutgoingIntraBssNAttemptSdcch - Y - Y
1169/0 hoUnsuccessOutgoingInterBssNAttemptTch - Y Y -
1170/0 hoUnsuccessOutgoingInterBssNAttemptSdcch - Y - Y
1172/0 dataNtRateFbTcbResLack - Y Y -
1172/1 dataNtRateFbTcbConfNotAllowed - Y Y -
1191/0 channelRequestCause[000...111] - Y Y -
1192/0 immediateAssignmentSuccessCause[000..111] - Y Y -
1193/0 estabIndicSignallingPagingRes - Y Y -
1193/1 estabIndicSignallingLocUpdate - Y Y -
1193/2 estabIndicSignallingReEstab - Y Y -
1193/3 estabIndicSignallingImsiDetach - Y Y -
1193/4 estabIndicSignallingMoc - Y Y -
1193/5 estabIndicSignallingEmergency - Y Y -
1193/6 estabIndicSignallingShortMsg - Y Y -
1193/7 estabIndicSignallingSuppService - Y Y -
1193/8 estabIndicSignallingPiggybacked - Y Y -
1195/0 estabIndicSigPhase1 - Y Y -
1196/0 estabIndicSigPhase2 - Y Y -
1197/0 channelActivateSpeechFullRate - Y Y -
1197/1 channelActivateSpeechEnhancedFullRate - Y Y -
1197/2 channelActivateSpeechAmrHr - Y Y -
1197/3 channelActivateSpeechAmrFr - Y Y -
1198/0 downlinkPowerCtrlMaxTch[Cum,Ech,Moy,Max] - Y Y -
1199/0 uplinkPowerCtrlMaxTch[Cum,Ech,Moy,Max] - Y Y -
1200/0 hoNcellsExecution - Y Y -
1202/0 hoNcellsExecutionSdcch - Y - Y
1204/0 hoNcellsUnsuccessTchChlR - Y Y -
1204/1 hoNcellsUnsuccessTchTimer - Y Y -
1204/2 hoNcellsUnsuccessTchOther - Y Y -
1205/0 hoNcellsUnsuccessSdcchChlR - Y - Y
1205/1 hoNcellsUnsuccessSdcchTimer - Y - Y
1205/2 hoNcellsUnsuccessSdcchOther - Y - Y
1206/0 speechAlgoFallBack - Y Y -
1206/1 amrFrSpeechAlgoFallBack - Y Y -
1207/0 immediateAssignmentMultiband - Y Y -
1208/0 hoRequestOutgoingMbandEbandMsDualb - Y Y -
1209/0 hoSuccessOutgoingMbandEbandMsDualb - Y Y -
1300/0 omcOutputIFrame N N N Y
1301/0 omcInputIFrame N N N Y
1302/0 omcOutputRepeatedIFrame N N N Y
1303/0 omcInputRepeatedIFrame N N N Y
1304/0 omcOutputRnrFrame N N N Y
1305/0 omcInputRnrFrame N N N Y
1400/0 prLoadCpue[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadCpue1[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadCpue2[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadCpum[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd0[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd1[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd2[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd3[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd4[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd5[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd6[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd7[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd8[Moy,Max,Cum,Ech] N N Y N
1400/0 prLoadSicd9[Moy,Max,Cum,Ech] N N Y N
1500/0 aTransparentUp - Y Y -
1501/0 aTransparentDown - Y Y -
1502/0 aNonTransparentUp - Y Y -
1503/0 aNonTransparentDown - Y Y -
1504/0 vgcsAccessGrant - - - -
1505/0 vgcsMscReject - - - -
1506/0 aintOverloadRejectedOpPageReq - Y Y -
1506/1 aintOverloadRejectedOpIncomingExtHoReq - Y Y -
1506/2 aintOverLoadRejectedOpVbsVgcsSetup - Y Y -
1506/3 aintOverLoadRejectedOpVbsVgcsAssignment - Y Y -
1506/4 aintOverLoadRejectedOpPerformLocationReq - Y Y -
1507/0 e3OverloadRejectedOpPagingReq - Y Y -
1507/1 e3OverloadRejectedOpChannelReq - Y Y -
1507/2 e3OverloadRejectedOpEstablishInd - Y Y -
1507/3 e3OverloadRejectedOpHoReq - Y Y -
1507/4 e3OverloadRejectedOpPagingReqReject - Y Y -
1507/5 e3OverloadRejectedOpSmsCb - Y Y -
1508/0 pagingFilteredByBsc - Y Y -
1600/0 connectionDurationTch[Cum,Ech,Moy,Max] - Y Y -
1600/0 connectionDurationTchTrZone[Cum,Ech,Moy,Max] - Y Y -
1601/0 downlinkPowerCtrlMaxSdcch[Cum,Ech,Moy,Max] - Y Y -
1602/0 uplinkPowerCtrlMaxSdcch[Cum,Ech,Moy,Max] - Y Y -
1603/0 connectionDurationSdcch[Cum,Ech,Moy,Max] - Y Y -
1603/0 connectionDurationSdcchTrZone[Cum,Ech,Moy,Max] - Y Y -
1604/0 pchAveragedQueueLength[Moy,Max,Cum,Ech] - Y Y -
1604/0 pchAveragedQueueLengthTs2[Moy,Max,Cum,Ech] - Y Y -
1604/0 pchAveragedQueueLengthTs4[Moy,Max,Cum,Ech] - Y Y -
1604/0 pchAveragedQueueLengthTs6[Moy,Max,Cum,Ech] - Y Y -
1605/0 pchQueuePagesDiscarded - Y Y -
1605/0 pchQueuePagesDiscardedTs2 - Y Y -
1605/0 pchQueuePagesDiscardedTs4 - Y Y -
1605/0 pchQueuePagesDiscardedTs6 - Y Y -
1606/0 sdcchAllocated - Y Y -
1606/0 sdcchAllocatedTrZone - Y Y -
1607/0 sdcchAveragedUsed[Moy,Max,Cum,Ech] Y Y Y -
1607/0 sdcchAveragedUsedTrZone[Moy,Max,Cum,Ech] Y Y Y -
1608/0 sdcchRessourceFailure - Y Y -
1608/0 sdcchRessourceFailureTrZone - Y Y -
1609/0 tchFrAllocatedTchAllocation - Y Y -
1609/0 tchFrAllocatedTchAllocationTrZone - Y Y -
1609/1 tchFrAllocatedPrimoAllocation - Y Y -
1609/1 tchFrAllocatedPrimoAllocationTrZone - Y Y -
1609/2 tchFrAllocatedOverflowAllocation - Y Y -
1609/2 tchFrAllocatedOverflowAllocationTrZone - Y Y -
1609/3 tchFrAllocatedWps - Y Y -
1609/3 tchFrAllocatedWpsTrZone - Y Y -
1610/0 tchHrAllocatedTchAllocation - Y Y -
1610/0 tchHrAllocatedTchAllocationTrZone - Y Y -
1610/1 tchHrAllocatedWps - Y Y -
1610/1 tchHrAllocatedWpsTrZone - Y Y -
1611/0 tchFrAveragedUsedTchAllocation[Moy,Max,Cum,Ech] - Y Y -
1611/0 tchFrAveragedUsedTchAllocation- - Y Y -
TrZone[Moy,Max,Cum,Ech]
1611/1 tchFrAveragedUsedPrimoAlloca- - Y Y -
tion[Moy,Max,Cum,Ech]
1611/1 tchFrAveragedUsedPrimoAllocation- - Y Y -
TrZone[Moy,Max,Cum,Ech]
1611/2 tchFrAveragedUsedOverflowAlloca- - Y Y -
tion[Moy,Max,Cum,Ech]
1611/2 tchFrAveragedUsedOverflowAllocation- - Y Y -
TrZone[Moy,Max,Cum,Ech]
1611/3 tchFrAveragedUsedWps[Moy,Max,Cum,Ech] - Y Y -
1611/3 tchFrAveragedUsedWpsTrZone[Moy,Max,Cum,Ech] - Y Y -
1612/0 tchHrAveragedUsedTchAllocation[Moy,Max,Cum,Ech] - - Y -
1612/0 tchHrAveragedUsedTchAllocation- - - Y -
TrZone[Moy,Max,Cum,Ech]
1612/1 tchHrAveragedUsedWps[Moy,Max,Cum,Ech] - - Y -
1612/1 tchHrAveragedUsedWpsTrZone[Moy,Max,Cum,Ech] - - Y -
1613/0 tchFrRessourceFailure - Y Y -
1613/0 tchFrRessourceFailureTrZone - Y Y -
1614/0 tchHrRessourceFailure - - Y -
1614/0 tchHrRessourceFailureTrZone - - Y -
1616/0 tchAveragedQueueLengthHighPrior- - Y Y -
ity[Moy,Max,Cum,Ech]
1616/1 tchAveragedQueueLengthOtherPrior- - Y Y -
ity[Moy,Max,Cum,Ech]
1617/0 tchQueuingExpirationHighPriority - Y Y -
1617/1 tchQueuingExpirationOtherPriority - Y Y -
1618/0 tchQueuingDurationHighPriority[Cum,Ech,Moy,Max] - Y Y -
1618/1 tchQueuingDurationOtherPriority[Cum,Ech,Moy,Max] - Y Y -
1619/0 channelAveragedIdlePerInterf- - Y Y -
Band0[Cum,Ech,Moy,Max]
1619/1 channelAveragedIdlePerInterf- - Y Y -
Band1[Cum,Ech,Moy,Max]
1619/2 channelAveragedIdlePerInterf- - Y Y -
Band2[Cum,Ech,Moy,Max]
1619/3 channelAveragedIdlePerInterf- - Y Y -
Band3[Cum,Ech,Moy,Max]
1619/4 channelAveragedIdlePerInterf- - Y Y -
Band4[Cum,Ech,Moy,Max]
1620/0 directedRetryUnsuccessNoBts - Y Y -
1621/0 sapi3SessionEstablishment - Y Y -
1622/0 msLostMeasurements - Y Y -
1622/0 msLostMeasurementsTrZone - Y Y -
1623/0 rxLevDownLink - Y Y -
1623/0 rxLevDownLinkTrZone - Y Y -
1624/0 rxLevUpLink - Y Y -
1624/0 rxLevUpLinkTrZone - Y Y -
1625/0 rxQualDownLink - Y Y -
1625/0 rxQualDownLinkTrZone - Y Y -
1626/0 rxQualUpLink - Y Y -
1626/0 rxQualUpLinkTrZone - Y Y -
1629/0 channelActivateSignallingFullRate - Y Y -
1629/1 channelActivateSignallingHalfRate - Y Y -
1700/0 tchFrAveragedAvailable[Moy,Max,Cum,Ech] Y Y Y -
1700/0 tchFrAveragedAvailableTrZone[Moy,Max,Cum,Ech] Y Y Y -
1701/0 sdcchAveragedAvailable[Moy,Max,Cum,Ech] - Y Y -
1701/0 sdcchAveragedAvailableTrZone[Moy,Max,Cum,Ech] - Y Y -
1702/0 channelRequestExtended - Y Y -
1705/0 channelActivateTchFrDataT16 - Y Y -
1705/1 channelActivateTchFrDataT600 - Y Y -
1705/2 channelActivateTchFrDataT1200 - Y Y -
1705/3 channelActivateTchFrDataT2400 - Y Y -
1705/4 channelActivateTchFrDataT4800 - Y Y -
1705/5 channelActivateTchFrDataT9600 - Y Y -
1705/6 channelActivateTchFrDataT14400 - Y Y -
1706/0 channelActivateTchHrDataT16 - - - -
1706/1 channelActivateTchHrDataT600 - - - -
1706/2 channelActivateTchHrDataT1200 - - - -
1706/3 channelActivateTchHrDataT2400 - - - -
1706/4 channelActivateTchHrDataT4800 - - - -
1707/0 channelActivateTchFrDataNT6000 - Y Y -
1707/1 channelActivateTchFrDataNT12000 - Y Y -
1707/2 channelActivateTchFrDataNT14500 - Y Y -
1708/0 channelActivateTchHrDataNT6000 - - - -
1709/0 channelActTchFrDataT - - - -
1710/0 channelActTchFrDataNT - - - -
1711/0 channelActTchHrDataT - - - -
1712/0 channelActTchHrDataNT - - - -
1714/0 btsOverloadDuration[Cum,Ech,Moy,Max] - Y Y -
1715/0 attemptedTchFrSeizuresMsDualb - Y Y -
1716/0 successfulTchFrSeizuresMsDualb - Y Y -
1717/0 abisTrauFrameDlReceived - Y Y -
1718/0 abisTrauFrameCorrected - Y Y -
1719/0 abisTrauFrameMuted - Y Y -
1720/0 radioFrameUlReceived - Y Y -
1721/0 ecuActivation - Y Y -
1722/0 asciCallInitiationVbs - - - -
1722/1 asciCallInitiationVgcs - - - -
1723/0 asciInbandPaging - - - -
1724/0 asciInbandNotification - - - -
1725/0 asciPreemptionPerformed - - - -
1726/0 dataNtRateFbTchResLack - Y Y -
1726/1 dataNtRateFbTchConfNotAllowed - Y Y -
1730/0 pagingResponse Y - - -
1744/0 tchFrAllocated - - - -
1744/0 tchFrAllocatedTrZone - - - -
1745/0 tchHrAllocated - - - -
1745/0 tchHrAllocatedTrZone - - - -
1746/0 tchFrAveragedUsed[Moy,Max,Cum,Ech] Y - - -
1746/0 tchFrAveragedUsedTrZone[Moy,Max,Cum,Ech] Y - - -
1747/0 tchHrAveragedUsed[Moy,Max,Cum,Ech] - - - -
1747/0 tchHrAveragedUsedTrZone[Moy,Max,Cum,Ech] - - - -
1748/0 channelRequest - - - -
1749/0 immediateAssignmentSuccess - - - -
1750/0 estabIndicSignalling Y - - -
1751/0 immediateAssignmentReject - - - -
1752/0 signallingReleaseNoBts - - - -
1753/0 signallingReleaseBts - - - -
1754/0 trafficRelease - - - -
1755/0 pcmFaultExternal - Y - -
1755/1 pcmFaultInternal - Y - -
1755/2 pcmFaultDDTIBoard - Y - -
1755/3 pcmFaultOutOfService - Y - -
1756/0 hoFailureIntraBtsTchRadioLack - Y - -
1756/1 hoFailureIntraBtsTchChannelActivateNack - Y - -
1756/2 hoFailureIntraBtsTchTchnAckTimerExp - Y - -
1757/0 hoFailureIntraBtsSdcchRadioLack - Y - -
1757/1 hoFailureIntraBtsSdcchChannelActivateNack - Y - -
1757/2 hoFailureIntraBtsSdcchTchnAckTimerExp - Y - -
1758/0 hoFailureIncomingIntraBssTchRadioLack - Y - -
1758/1 hoFailureIncomingIntraBssTchHoNotAllowed - Y - -
1758/2 hoFailureIncomingIntraBssTchChannelActivateNack - Y - -
1758/3 hoFailureIncomingIntraBssTchTchnAckTimerExp - Y - -
1758/4 hoFailureIncomingIntraBssTchIncompatible - Y - -
1759/0 hoFailureIncomingIntraBssSdcchRadioLack - Y - -
1759/1 hoFailureIncomingIntraBssSdcchHoNotAllowed - Y - -
1759/2 hoFailureIncomingIntraBssSdcchChannelActivateNack - Y - -
1759/3 hoFailureIncomingIntraBssSdcchTchnAckTimerExp - Y - -
1760/0 hoFailureIncomingInterBssTchRadioLack - Y - -
1760/1 hoFailureIncomingInterBssTchTerrestLack - Y - -
1760/2 hoFailureIncomingInterBssTchHoNotAllowed - Y - -
1760/3 hoFailureIncomingInterBssTchChannelActivateNack - Y - -
1760/4 hoFailureIncomingInterBssTchTchnAckTimerExp - Y - -
1760/5 hoFailureIncomingInterBssTchCICIncompatible - Y - -
1761/0 hoFailureIncomingInterBssSdcchRadioLack - Y - -
1761/1 hoFailureIncomingInterBssSdcchTerrestLack - Y - -
1761/2 hoFailureIncomingInterBssSdcchHoNotAllowed - Y - -
1761/3 hoFailureIncomingInterBssSdcchChannelActivateNack - Y - -
1761/4 hoFailureIncomingInterBssSdcchTchnAckTimerExp - Y - -
1762/0 hoFailureOutgoingIntraBssTchRadioLack - Y - -
1762/1 hoFailureOutgoingIntraBssTchHoNotAllowed - Y - -
1762/2 hoFailureOutgoingIntraBssTchChannelActivateNack - Y - -
1762/3 hoFailureOutgoingIntraBssTchTchnAckTimerExp - Y - -
1762/4 hoFailureOutgoingIntraBssTchIncompatible - Y - -
1763/0 hoFailureOutgoingIntraBssSdcchRadioLack - Y - -
1763/1 hoFailureOutgoingIntraBssSdcchHoNotAllowed - Y - -
1763/2 hoFailureOutgoingIntraBssSdcchChannelActivateNack - Y - -
1763/3 hoFailureOutgoingIntraBssSdcchTchnAckTimerExp - Y - -
1764/0 hoFailureOutgoingInterBssTchRadioLack - Y - -
1764/1 hoFailureOutgoingInterBssTchTerrestLack - Y - -
1764/2 hoFailureOutgoingInterBssTchHoNotAllowed - Y - -
1764/3 hoFailureOutgoingInterBssTchT7TimerExp - Y - -
1764/4 hoFailureOutgoingInterBssTchOtherCases - Y - -
1764/5 hoFailureOutgoingInterBssTchIncompatible - Y - -
1765/0 hoFailureOutgoingInterBssSdcchRadioLack - Y - -
1765/1 hoFailureOutgoingInterBssSdcchTerrestLack - Y - -
1765/2 hoFailureOutgoingInterBssSdcchHoNotAllowed - Y - -
1765/3 hoFailureOutgoingInterBssSdcchT7TimerExp - Y - -
1765/4 hoFailureOutgoingInterBssSdcchOtherCase - Y - -
1768/0 hoUnsuccessOutgoingIntraCellTchReturnOldChannel - Y - -
1768/1 hoUnsuccessOutgoingIntraCellTchT3103TimerExp - Y - -
1769/0 hoUnsuccessOutgoingIntraCellSdcchReturnOldChannel - Y - -
1769/1 hoUnsuccessOutgoingIntraCellSdcchT3103TimerExp - Y - -
1770/0 hoUnsuccessOutgoingInterCellTchReturnOldChannel - Y - -
1770/1 hoUnsuccessOutgoingInterCellTchT3103TimerExp - Y - -
1770/2 hoUnsuccessOutgoingInterCellTchOtherCases - Y - -
1771/0 hoUnsuccessOutgoingInterCellSdcchReturnOldChannel - Y - -
1771/1 hoUnsuccessOutgoingInterCellSdcchT3103TimerExp - Y - -
1771/2 hoUnsuccessOutgoingInterCellSdcchOtherCases - Y - -
1772/0 hoUnsuccessIncomingIntraCellTchReturnOldChannel - Y - -
1772/1 hoUnsuccessIncomingIntraCellTchT3103TimerExp - Y - -
1773/0 hoUnsuccessIncomingIntraCellSdcchReturnOldChannel - Y - -
1773/1 hoUnsuccessIncomingIntraCellSdcchT3103TimerExp - Y - -
1774/0 hoUnsuccessIncomingInterBssTchTimerExp - Y - -
1774/1 hoUnsuccessIncomingInterBssTchOtherCases - Y - -
1775/0 hoUnsuccessIncomingInterBssSdcchTimerExp - Y - -
1775/1 hoUnsuccessIncomingInterBssSdcchOtherCases - Y - -
1776/0 hoRequiredTch - - Y -
1777/0 hoRequiredSdcch - - - -
1778/0 signallingAbnormalReleaseCell - Y Y -
1779/0 trafficAbnormalRelease - Y Y -
1780/0 hoSuccessOutgoingTch Y - Y -
1780/1 amrFrHoSuccessOutgoingTch Y - Y -
1780/2 amrHrHoSuccessOutgoingTch Y - Y -
1781/0 hoSuccessIncomingTch Y - Y -
1782/0 hoBtsRejected - Y Y -
1783/0 hoRequestOutgoingMbandMbandMsDualb - Y Y -
1784/0 hoRequestOutgoingEbandEbandMsDualb - Y Y -
1785/0 hoRequestOutgoingEbandMbandMsDualb - Y Y -
1786/0 hoSuccessOutgoingMbandMbandMsDualb - Y Y -
1787/0 hoSuccessOutgoingEbandEbandMsDualb - Y Y -
1788/0 hoSuccessOutgoingEbandMbandMsDualb - Y Y -
1789/0 hoExecutionOutgoingMbandEbandMsDualb - Y Y -
1790/0 hoExecutionOutgoingMbandMbandMsDualb - Y Y -
1791/0 hoExecutionOutgoingEbandEbandMsDualb - Y Y -
1792/0 hoExecutionOutgoingEbandMbandMsDualb - Y Y -
1793/0 hoRequestIncomingIntraBssTchMsDualb - Y Y -
1794/0 hoExecutionIncomingIntraBssTchMsDualb - Y Y -
1795/0 hoSuccessIncomingIntraBssTchMsDualb - Y Y -
1796/0 hoRequestIntraBtsMsDualb - Y Y -
1797/0 hoExecutionIntraBtsMsDualb - Y Y -
1798/0 hoSuccessIntraBtsMsDualb - Y Y -
1799/0 assignToOtherBandOrZone - Y Y -
1800/0 asciTalkerHandoverVbs - - - -
1800/1 asciTalkerHandoverVgcs - - - -
1801/0 hoFailureTieringTchNorrLargeToSmallPattern - Y Y -
1801/1 hoFailureTieringTchNorrSmallToLargePattern - Y Y -
1802/0 hoSuccessTieringTchLargeToSmallPattern - Y Y -
1802/1 hoSuccessTieringTchSmallToLargePattern - Y Y -
1803/0 cgOverloadRejectedOpPageReqCg0 - Y Y -
1803/0 cgOverloadRejectedOpPageReqCg1 - Y Y -
1803/0 cgOverloadRejectedOpPageReqCg2 - Y Y -
1803/1 cgOverloadRejectedOpChannelReqCg0 - Y Y -
1803/1 cgOverloadRejectedOpChannelReqCg1 - Y Y -
1803/1 cgOverloadRejectedOpChannelReqCg2 - Y Y -
1803/2 cgOverloadRejectedOpEstablishIndCg0 - Y Y -
1803/2 cgOverloadRejectedOpEstablishIndCg1 - Y Y -
1803/2 cgOverloadRejectedOpEstablishIndCg2 - Y Y -
1803/3 cgOverloadRejectedOpHoReqCg0 - Y Y -
1803/3 cgOverloadRejectedOpHoReqCg1 - Y Y -
1803/3 cgOverloadRejectedOpHoReqCg2 - Y Y -
1803/4 cgOverloadRejectedOpPageReqBtsCg0 - Y Y -
1803/4 cgOverloadRejectedOpPageReqBtsCg1 - Y Y -
1803/4 cgOverloadRejectedOpPageReqBtsCg2 - Y Y -
1803/5 cgOverloadRejectedOpSmsCbCg0 - Y Y -
1803/5 cgOverloadRejectedOpSmsCbCg1 - Y Y -
1803/5 cgOverloadRejectedOpSmsCbCg2 - Y Y -
1804/0 deleteIndication - Y Y -
1805/0 msPowerIncControl - Y Y -
1806/0 msPowerDecControl - Y Y -
1807/0 bsPowerIncControl - Y Y -
1808/0 bsPowerDecControl - Y Y -
1809/0 timingAdvanceAverage - Y Y -
1809/0 timingAdvanceAverageTrZone - Y Y -
1809/1 timingAdvanceMaximum - Y Y -
1809/1 timingAdvanceMaximumTrZone - Y Y -
1810/0 tchFrAverageConfigurated[Moy,Max,Cum,Ech] - Y Y -
1810/0 tchFrAverageConfiguratedTrZone[Moy,Max,Cum,Ech] - Y Y -
1811/0 sdcchAverageConfigurated[Moy,Max,Cum,Ech] - Y Y -
1811/0 sdcchAverageConfiguratedTrZone[Moy,Max,Cum,Ech] - Y Y -
1812/0 allocatedCircuitTs[Moy,Max,Cum,Ech] - Y Y -
1812/0 allocatedCircuitTsTrZone[Moy,Max,Cum,Ech] - Y Y -
1813/0 allocatedPacketTs[Moy,Max,Cum,Ech] - Y Y -
1813/0 allocatedPacketTsTrZone[Moy,Max,Cum,Ech] - Y Y -
1813/1 totalNumberOfPacketTs[Moy,Max,Cum,Ech] - Y Y -
1813/1 totalNumberOfPacketTsTrZone[Moy,Max,Cum,Ech] - Y Y -
1813/2 totalNumberOfPacketTsUsedForCir- - Y Y -
cuit[Moy,Max,Cum,Ech]
1813/2 totalNumberOfPacketTsUsedForCircuitTr- - Y Y -
Zone[Moy,Max,Cum,Ech]
1814/0 gprsPreemption - Y Y -
1815/0 gprsPreemptionNack - Y Y -
1816/0 pathBalance[Cum,Ech,Moy,Max] - Y Y -
1817/0 burstToTransmit - - - Y
1818/0 burstTransmitted - - - Y
1819/0 burstToTransmitReqPwr - - - Y
1820/0 STPMAttenuation - - - Y
1821/0 allocatedCircuitTsCell[Moy,Max,Cum,Ech] - Y Y -
1822/0 allocatedPacketTsCell[Moy,Max,Cum,Ech] - Y Y -
1822/1 totalNumberOfPacketTsCell[Moy,Max,Cum,Ech] - Y Y -
1822/2 totalNumberOfPacketTsUsedForCircuit- - Y Y -
Cell[Moy,Max,Cum,Ech]
1823/0 allTchFrAllocatedTimeCell[Cum,Ech,Moy,Max] - Y Y -
1824/0 tchFrAveragedUsedTchAllocation- - Y Y -
Cell[Moy,Max,Cum,Ech]
1824/1 tchFrAveragedUsedPrimoAllocation- - Y Y -
Cell[Moy,Max,Cum,Ech]
1824/2 tchFrAveragedUsedOverflowAllocation- - Y Y -
Cell[Moy,Max,Cum,Ech]
1824/3 tchFrAveragedUsedWpsCell[Moy,Max,Cum,Ech] - Y Y -
1825/0 tchFrAveragedAvailableCell[Moy,Max,Cum,Ech] Y Y Y -
1826/0 tchFrAveragedUsedCell[Moy,Max,Cum,Ech] Y - - -
1827/0 tchFrAverageConfiguratedCell[Moy,Max,Cum,Ech] - Y Y -
1828/0 tchHrAveragedUsedCell[Moy,Max,Cum,Ech] - - Y -
1828/1 tchHrAveragedUsedWpsCell[Moy,Max,Cum,Ech] - - Y -
1829/0 tchHrAveragedUsedNscCell[Moy,Max,Cum,Ech] - - - -
1834/0 lapdOverloadRejectedOpSicd0 N N Y N
1834/0 lapdOverloadRejectedOpSicd1 N N Y N
1834/0 lapdOverloadRejectedOpSicd2 N N Y N
1834/0 lapdOverloadRejectedOpSicd3 N N Y N
1834/0 lapdOverloadRejectedOpSicd4 N N Y N
1834/0 lapdOverloadRejectedOpSicd5 N N Y N
1834/0 lapdOverloadRejectedOpSicd6 N N Y N
1834/0 lapdOverloadRejectedOpSicd7 N N Y N
1834/0 lapdOverloadRejectedOpSicd8 N N Y N
1834/0 lapdOverloadRejectedOpSicd9 N N Y N
1835/0 cardSynthLoadCpue0[Moy,Max,Cum,Ech] N N Y N
1835/0 cardSynthLoadCpue1[Moy,Max,Cum,Ech] N N Y N
1835/0 cardSynthLoadCpue2[Moy,Max,Cum,Ech] N N Y N
1835/0 cardSynthLoadCpum[Moy,Max,Cum,Ech] N N Y N
1835/0 cardSynthLoadSicd[0..9][Moy,Max,Cum,Ech] N N Y N
1839/0 hoNcellsRequestOutgoingUplinkStrength N Y N N
1839/1 hoNcellsRequestOutgoingDownlinkStrength N Y N N
1839/2 hoNcellsRequestOutgoingUplinkQuality N Y N N
1839/3 hoNcellsRequestOutgoingDownlinkQuality N Y N N
1839/4 hoNcellsRequestOutgoingDistance N Y N N
1839/5 hoNcellsRequestOutgoingPowerBudget N Y N N
1839/6 hoNcellsRequestOutgoingDirectedRetry N Y N N
1839/7 hoNcellsRequestOutgoingInterCellOM N Y N N
1839/8 hoNcellsRequestOutgoingTraffic N Y N N
1839/9 hoNcellsRequestOutgoingOther N Y N N
1840/0 hoNcellsSuccessOutgoingUplinkStrength N Y N N
1840/1 hoNcellsSuccessOutgoingDownlinkStrength N Y N N
1840/2 hoNcellsSuccessOutgoingUplinkQuality N Y N N
1840/3 hoNcellsSuccessOutgoingDownlinkQuality N Y N N
1840/4 hoNcellsSuccessOutgoingDistance N Y N N
1840/5 hoNcellsSuccessOutgoingPowerBudget N Y N N
1840/6 hoNcellsSuccessOutgoingDirectedRetry N Y N N
1840/7 hoNcellsSuccessOutgoingInterCellOM N Y N N
1840/8 hoNcellsSuccessOutgoingTraffic N Y N N
1840/9 hoNcellsSuccessOutgoingOther N Y N N
1841/0 assignRequestSdcchToTchChannel - Y Y -
1841/1 assignRequestOthers - Y Y -
1842/0 assignRequestAintSdcchToTchChannel - Y Y -
1842/1 assignRequestAintOthers - Y Y -
1900/0 amrFrTchAllocated - - Y -
1900/0 amrFrTchAllocatedTrZone - - Y -
1901/0 amrFrTchStdAveragedUsed[Moy,Max,Cum,Ech] - - Y -
1901/0 amrFrTchStdAveragedUsedTrZone[Moy,Max,Cum,Ech] - - Y -
1902/0 amrFrTchConnectionDuration[Cum,Ech,Moy,Max] - - Y -
1902/0 amrFrTchConnectionDuration- - - Y -
TrZone[Cum,Ech,Moy,Max]
1902/1 amrHrTchConnectionDuration[Cum,Ech,Moy,Max] - - Y -
1902/1 amrHrTchConnectionDuration- - - Y -
TrZone[Cum,Ech,Moy,Max]
1903/0 amrFrTchSuccessfullyAssigned - - Y -
1903/1 amrHrTchSuccessfullyAssigned - - Y -
1904/0 amrFrTchAssignFailure - - Y -
1904/1 amrHrTchAssignFailure - - Y -
1905/0 CIUplinkFr - - Y -
1905/0 CIUplinkFrTrZone - - Y -
1906/0 downlinkPowerCtrlMaxTchAmrFr[Cum,Ech,Moy,Max] - - Y -
1907/0 uplinkPowerCtrlMaxTchAmrFr[Cum,Ech,Moy,Max] - - Y -
1908/0 RxLevDownlinkAmrFr - - Y -
1908/0 RxLevDownlinkAmrFrTrZone - - Y -
1909/0 RxLevUplinkAmrFr - - Y -
1909/0 RxLevUplinkAmrFrTrZone - - Y -
1910/0 RxQualDownlinkAmrFr - - Y -
1910/0 RxQualDownlinkAmrFrTrZone - - Y -
1911/0 RxQualUplinkAmrFr - - Y -
1911/0 RxQualUplinkAmrFrTrZone - - Y -
1912/0 msPowerIncControlAmrFr - - Y -
1913/0 msPowerDecControlAmrFr - - Y -
1914/0 bsPowerIncControlAmrFr - - Y -
1915/0 bsPowerDecControlAmrFr - - Y -
1916/0 CIUplinkAmrFr - - Y -
1916/0 CIUplinkAmrFrTrZone - - Y -
1917/0 timingAdvanceAmrFrAvg - - Y -
1917/1 timingAdvanceAmrFrMax - - Y -
1918/0 downlinkPowerCtrlMaxTchAmrHr[Cum,Ech,Moy,Max] - - Y -
1919/0 uplinkPowerCtrlMaxTchAmrHr[Cum,Ech,Moy,Max] - - Y -
1920/0 RxLevDownlinkAmrHr - - Y -
1920/0 RxLevDownlinkAmrHrTrZone - - Y -
1921/0 RxLevUplinkAmrHr - - Y -
1921/0 RxLevUplinkAmrHrTrZone - - Y -
1922/0 RxQualDownlinkAmrHr - - Y -
1922/0 RxQualDownlinkAmrHrTrZone - - Y -
1923/0 RxQualUplinkAmrHr - - Y -
1923/0 RxQualUplinkAmrHrTrZone - - Y -
1924/0 msPowerIncControlAmrHr - - Y -
1925/0 msPowerDecControlAmrHr - - Y -
1926/0 bsPowerIncControlAmrHr - - Y -
1927/0 bsPowerDecControlAmrHr - - Y -
1928/0 CIUplinkAmrHr - - Y -
1928/0 CIUplinkAmrHrTrZone - - Y -
1929/0 timingAdvanceAmrHrAvg - - Y -
1929/1 timingAdvanceAmrHrMax - - Y -
1930/0 msLostMeasurementsAmrFr - - Y -
1930/0 msLostMeasurementsAmrFrTrZone - - Y -
1931/0 msLostMeasurementsAmrHr - - Y -
1931/0 msLostMeasurementsAmrHrTrZone - - Y -
1932/0 qualityHoFiltered - - Y -
1933/0 capacityHoFiltered - - Y -
1934/0 amrFrTchStdAveragedUsedCell[Moy,Max,Cum,Ech] - - Y -
1935/0 amrHrModeDuration - - Y -
1936/0 amrCellLoadStateModification - - Y -
1937/0 amrFilteredBusyTchRatio[Moy,Max,Cum,Ech] - - Y -
1938/0 amrCellLoadStateUnderevaluated - - Y -
1939/0 amrCellLoadStateOverevaluated - - Y -
1950/0 intracellAmrFrUpHoRequiredTch - - Y -
1950/1 intracellAmrFrDownHoRequiredTch - - Y -
1950/2 amrQualityFrUpHoRequiredTch - - Y -
1950/3 amrQualityFrDownHoRequiredTch - - Y -
1950/4 capacityFrToHrHoRequiredTch - - Y -
1951/0 alarmAmrHrToFrUpHoRequiredTch - - Y -
1951/1 alarmAmrHrToFrDownHoRequiredTch - - Y -
1951/2 amrQualityHrUpHoRequiredTch - - Y -
1951/3 amrQualityHrDownHoRequiredTch - - Y -
1952/0 amrFrHoRequestOutgoingTch - - Y -
1952/1 amrHrHoRequestOutgoingTch - - Y -
1953/0 amrFrHoRequestIntraCellTch - - Y -
1953/1 amrFrToHrHoRequestIntraCellTch - - Y -
1953/2 amrHrToFrHoRequestIntraCellTch - - Y -
1954/0 amrFrHoExecutionIntraCellTch - - Y -
1954/1 amrFrToHrHoExecutionIntraCellTch - - Y -
1954/2 amrHrToFrHoExecutionIntraCellTch - - Y -
1955/0 amrFrHoSuccessIntraCellTch - - Y -
1955/1 amrFrToHrHoSuccessIntraCellTch - - Y -
1955/2 amrHrToFrHoSuccessIntraCellTch - - Y -
1956/0 hoNCellsExecutionTchAmrHr - - Y -
1957/0 hoNCellsExecutionTchAmrFr - - Y -
1958/0 hoNCellsUnsuccessTchAmrHrHandoverFailure - - Y -
1958/1 hoNCellsUnsuccessTchAmrHrTimerExpiration - - Y -
1958/2 hoNCellsUnsuccessTchAmrHrClearCommand - - Y -
1959/0 hoNCellsUnsuccessTchAmrFrHandoverFailure - - Y -
1959/1 hoNCellsUnsuccessTchAmrFrTimerExpiration - - Y -
1959/2 hoNCellsUnsuccessTchAmrFrClearCommand - - Y -
1960/0 trafficReleaseAmrFrLapdmCause - - Y -
1960/1 trafficReleaseAmrFrRadioCause - - Y -
1960/2 trafficReleaseAmrFrOthersCause - - Y -
1961/0 trafficReleaseAmrHrLapdmCause - - Y -
1961/1 trafficReleaseAmrHrRadioCause - - Y -
1961/2 trafficReleaseAmrHrOthersCause - - Y -
1963/0 hoNCellsRequestOutgoingAmrHr - - Y -
1964/0 hoNCellsRequestOutgoingAmrFr - - Y -
1975/0 amrFrUplinkCodec475 - - - Y
1975/0 amrFrUplinkCodec475TrZone - - - Y
1975/1 amrFrUplinkCodec59 - - - Y
1975/1 amrFrUplinkCodec59TrZone - - - Y
1975/2 amrFrUplinkCodec67 - - - Y
1975/2 amrFrUplinkCodec67TrZone - - - Y
1975/3 amrFrUplinkCodec102 - - - Y
1975/3 amrFrUplinkCodec102TrZone - - - Y
1976/0 amrHrUplinkCodec475 - - - Y
1976/0 amrHrUplinkCodec475TrZone - - - Y
1976/1 amrHrUplinkCodec59 - - - Y
1976/1 amrHrUplinkCodec59TrZone - - - Y
1976/2 amrHrUplinkCodec67 - - - Y
1976/2 amrHrUplinkCodec67TrZone - - - Y
1977/0 amrFrDownlinkCodec475 - - - Y
1977/0 amrFrDownlinkCodec475TrZone - - - Y
1977/1 amrFrDownlinkCodec59 - - - Y
1977/1 amrFrDownlinkCodec59TrZone - - - Y
1977/2 amrFrDownlinkCodec67 - - - Y
1977/2 amrFrDownlinkCodec67TrZone - - - Y
1977/3 amrFrDownlinkCodec102 - - - Y
1977/3 amrFrDownlinkCodec102TrZone - - - Y
1978/0 amrHrDownlinkCodec475 - - - Y
1978/0 amrHrDownlinkCodec475TrZone - - - Y
1978/1 amrHrDownlinkCodec59 - - - Y
1978/1 amrHrDownlinkCodec59TrZone - - - Y
1978/2 amrHrDownlinkCodec67 - - - Y
1978/2 amrHrDownlinkCodec67TrZone - - - Y
1979/0 amrFrBadSpeechFramesCodec475 - - - Y
1979/0 amrFrBadSpeechFramesCodec475TrZone - - - Y
1979/1 amrFrBadSpeechFramesCodec59 - - - Y
1979/1 amrFrBadSpeechFramesCodec59TrZone - - - Y
1979/2 amrFrBadSpeechFramesCodec67 - - - Y
1979/2 amrFrBadSpeechFramesCodec67TrZone - - - Y
1979/3 amrFrBadSpeechFramesCodec102 - - - Y
1979/3 amrFrBadSpeechFramesCodec102TrZone - - - Y
1980/0 amrFrValidSpeechFramesCodec475 - - - Y
1980/0 amrFrValidSpeechFramesCodec475TrZone - - - Y
1980/1 amrFrValidSpeechFramesCodec59 - - - Y
1980/1 amrFrValidSpeechFramesCodec59TrZone - - - Y
1980/2 amrFrValidSpeechFramesCodec67 - - - Y
1980/2 amrFrValidSpeechFramesCodec67TrZone - - - Y
1980/3 amrFrValidSpeechFramesCodec102 - - - Y
1980/3 amrFrValidSpeechFramesCodec102TrZone - - - Y
1981/0 amrHrBadSpeechFramesCodec475 - - - Y
1981/0 amrHrBadSpeechFramesCodec475TrZone - - - Y
1981/1 amrHrBadSpeechFramesCodec59 - - - Y
1981/1 amrHrBadSpeechFramesCodec59TrZone - - - Y
1981/2 amrHrBadSpeechFramesCodec67 - - - Y
1981/2 amrHrBadSpeechFramesCodec67TrZone - - - Y
1982/0 amrHrValidSpeechFramesCodec475 - - - Y
1982/0 amrHrValidSpeechFramesCodec475TrZone - - - Y
1982/1 amrHrValidSpeechFramesCodec59 - - - Y
1982/1 amrHrValidSpeechFramesCodec59TrZone - - - Y
1982/2 amrHrValidSpeechFramesCodec67 - - - Y
1982/2 amrHrValidSpeechFramesCodec67TrZone - - - Y
1983/0 amrUplinkNoDataFrames - - - Y
1983/1 amrDownlinkNoDataFrames - - - Y
1984/0 incAmrFrUpModif - - - Y
1984/0 incAmrFrUpModifTrZone - - - Y
1984/1 decAmrFrUpModif - - - Y
1984/1 decAmrFrUpModifTrZone - - - Y
1985/0 incAmrFrDownModif - - - Y
1985/0 incAmrFrDownModifTrZone - - - Y
1985/1 decAmrFrDownModif - - - Y
1985/1 decAmrFrDownModifTrZone - - - Y
1986/0 incAmrHrUpModif - - - Y
1986/0 incAmrHrUpModifTrZone - - - Y
1986/1 decAmrHrUpModif - - - Y
1986/1 decAmrHrUpModifTrZone - - - Y
1987/0 incAmrHrDownModif - - - Y
1987/0 incAmrHrDownModifTrZone - - - Y
1987/1 decAmrHrDownModif - - - Y
1987/1 decAmrHrDownModifTrZone - - - Y
1988/0 amrReversalPhaseFailure - - - Y
2000/0 totalNumberOfEdgeTs[Moy,Max,Cum,Ech] - Y Y -
2000/0 totalNumberOfEdgeTsTrZone[Moy,Max,Cum,Ech] - Y Y -
2000/1 allocatedEdgeTs[Moy,Max,Cum,Ech] - Y Y -
2000/1 allocatedEdgeTsTrZone[Moy,Max,Cum,Ech] - Y Y -
2000/2 preemptedEdgeTs[Moy,Max,Cum,Ech] - Y Y -
2000/2 preemptedEdgeTsTrZone[Moy,Max,Cum,Ech] - Y Y -
2001/0 allocatedAbisJokerTSEdge[Moy,Max,Cum,Ech] - - Y Y
2001/0 allocatedAbisJokerTSEdgeTrZone[Moy,Max,Cum,Ech] - - Y Y
2002/0 totalNumberOfEdgeTsCell[Moy,Max,Cum,Ech] - Y Y -
2002/1 allocatedEdgeTsCell[Moy,Max,Cum,Ech] - Y Y -
2002/2 preemptedEdgeTsCell[Moy,Max,Cum,Ech] - Y Y -
2003/0 allocatedAbisJokerTsCell[Moy,Max,Cum,Ech] - - Y Y
2010/0 WQUEUED1 - Y Y -
2010/1 WQUEUED2 - Y Y -
2010/2 WQUEUED3 - Y Y -
2010/3 WQUEUED4 - Y Y -
2010/4 WQUEUED5 - Y Y -
2011/0 WQOVFL1 - Y Y -
2011/1 WQOVFL2 - Y Y -
2011/2 WQOVFL3 - Y Y -
2011/3 WQOVFL4 - Y Y -
2011/4 WQOVFL5 - Y Y -
2012/0 WQTOUT1 - Y Y -
2012/1 WQTOUT2 - Y Y -
2012/2 WQTOUT3 - Y Y -
2012/3 WQTOUT4 - Y Y -
2012/4 WQTOUT5 - Y Y -
2013/0 wpsAccessBarringDurationClass0to9 - Y Y -
2013/1 wpsAccessBarringDurationClass11 - Y Y -
2013/2 wpsAccessBarringDurationClass12 - Y Y -
2013/3 wpsAccessBarringDurationClass13 - Y Y -
2013/4 wpsAccessBarringDurationClass14 - Y Y -
2013/5 wpsAccessBarringDurationClass15 - Y Y -
2014/0 WPUBWPSQ - Y Y -
2015/0 WQABAND - Y Y -
2016/0 WQUEDHO - Y Y -
2025/0 downgradedL1mModeOnClassmark - Y Y -
2035/0 msClassSensitivityToggle - - - -
2036/0 attemptedTchFrSeizures8W - - - -
2037/0 successfulTchFrSeizures8W - - - -
2038/0 hoSuccessOutgoingIntraBss8W - - - -
2039/0 hoSuccessOutgoingInterBss8W - - - -
2040/0 hoRequestIncomingIntraBss8W - - - -
2041/0 hoRequestIncomingInterBss8W - - - -
2042/0 hoSuccessIncomingIntraBss8W - - - -
2043/0 hoSuccessIncomingInterBss8W - - - -
2044/0 hoRequestOutgoingIntraBss8W - - - -
2045/0 hoRequestOutgoingInterBss8W - - - -
2046/0 hoRequestIntraBts8W - - - -
2047/0 hoSuccessIntraBts8W - - - -
2048/0 hoSuccessOutgoingIntraBssSdcch8W - - - -
2049/0 hoSuccessOutgoingInterBssSdcch8W - - - -
2050/0 hoRequestOutgoingIntraBssSdcch8W - - - -
2051/0 hoRequestOutgoingInterBssSdcch8W - - - -
2052/0 signallingReleaseBts8w - - - -
2052/1 signallingReleaseBtsT3107CircDown8W - - - -
2053/0 trafficRelease8W - - - -
2054/0 estabIndicSignallingEmergency8W - - - -
2055/0 estabIndicSigPhase28W - - - -
2056/0 hoUnsuccessOutgoingIntraCellTchReturnOldChan- - - - -
nel8W
2056/1 hoUnsuccessOutgoingIntraCellTchT3103TimerExp8W - - - -
2057/0 hoUnsuccessOutgoingInterCellTchReturnOldChan- - - - -
nel8W
2057/1 hoUnsuccessOutgoingInterCellTchT3103TimerExp8W - - - -
2058/0 signallingAbnormalReleaseCell8W - - - -
2059/0 trafficAbnormalRelease8W - - - -
2060/0 uplinkFreeUplinkReply - - - -
2061/0 listenerDetectionExpiry - - - -
2066/0 suspendRequest - - Y -
2067/0 resumeSuccess - - Y -
2068/0 resumeFailureAfterHOInterRA - - Y -
2068/1 resumeFailureAfterHOInterBSC - - Y -
2071/0 agprsSuspendRequestProcedures - - Y -
2071/1 agprsSuspendRequestMessages - - Y -
2072/0 agprsSuspendNack - - Y -
2073/0 agprsResumeRequest - - Y -
2074/0 agprsResumeNack - - Y -
2096/0 saicTchSuccessfullyAssigned - Y Y -
2096/0 saicTchSuccessfullyAssignedTrZone - Y Y -
3000/0 prLoadCne3OmuSbc[Moy,Max,Cum,Ech] - Y Y -
3001/0 prLoadCne3TmuSbc[Moy,Max,Cum,Ech] - Y Y -
3001/2 prLoadCne3TmuPmc[Moy,Max,Cum,Ech] - Y Y -
3004/0 e3PrMemCnOmuSbcMem[Cum,Ech,Moy,Max] - Y Y -
3004/1 e3PrMemCnOmuSbcSwap[Cum,Ech,Moy,Max] - Y Y -
3005/0 e3PrMemCnTmuSbc[Cum,Ech,Moy,Max] - Y Y -
3005/2 e3PrMemCnTmuPmc[Cum,Ech,Moy,Max] - Y Y -
3008/0 e3PrDiskCnOmuLdW[Cum,Ech,Moy,Max] - Y Y -
3008/1 e3PrDiskCnOmuLdR[Cum,Ech,Moy,Max] - Y Y -
3008/2 e3PrDiskCnOmuMdW[Cum,Ech,Moy,Max] - Y Y -
3008/3 e3PrDiskCnOmuMdR[Cum,Ech,Moy,Max] - Y Y -
3004/0 e3PrMemCnOmuSbcMemMoy/Max/Cum
/Ech
3004/1 e3PrMemCnOmuSbcSwapMoy/Max/Cu
m/Ech
3005/0 e3PrMemCnTmuSbcMoy/Max/Cum/Ech
3005/2 e3PrMemCnTmuPmcMoy/Max/Cum/Ech
3008 /0 e3PrDiskCnOmuLdWMoy/Max/Cum/Ech
3008/1 e3PrDiskCnOmuLdRMoy/Max/Cum/Ech
3008/2 e3PrDiskCnOmuMdWMoy/Max/Cum/Ech
3008/3 e3PrDiskCnOmuMdRMoy/Max/Cum/Ech
4.6 Md counters
This section lists the md counters, grouped by counter family. Md counters belong
to the following families:
FMD--R disk usage
FTAM
MD--R activity
MD--R cpu
MD--R database
MD--R X25
4.6.2 FTAM
Counter No. Q3 Name Type
129/0 ftamFtiGet totalizer
130/0 ftamFtiGetConf totalizer
131/0 ftamFtiPut totalizer
132/0 ftamFtiPutConf totalizer
133/0 ftamFtiDelete totalizer
134/0 ftamFtiDeleteConf totalizer
135/0 ftamFtiDir totalizer
136/0 ftamFtiDirConf totalizer
137/0 ftamFtiRename totalizer
138/0 ftamFtiRenameConf totalizer
network
bsc pcusn
bts pModule
transceiverZone ccch
CDL CDL Attribute Id/SubId Type Class SDO name Created GPRS
Comp. in /
release EDGE
PcmLink octetsDn 15001/0 CUM PCM idem CDL Attribute V12.4C G/E
PcmLink octetsUp 15001/1 CUM PCM idem CDL Attribute V12.4C G/E
Bvc pduDataDn 15004/0 CUM CELL idem CDL Attribute V12.4C G/E
Bvc pduDataUp 15004/1 CUM CELL idem CDL Attribute V12.4C G/E
Bvc octetsDataDn 15005/0 CUM CELL idem CDL Attribute V12.4C G/E
Bvc octetsDataUp 15005/1 CUM CELL idem CDL Attribute V12.4C G/E
Bvc bvcBlockRequests 15007/0 CUM CELL octetDiscarded V14.2/3 G/E
Bvc maxSizeDataDn 15007/1 CUM CELL pcuDlThroughputCum V15.0 G
Bvc maxSizeDataUp 15007/1 NBS CELL pcuDlThroughputNbs V15.0 G
Bvc maxSizeDataUp 15007/1 AVG CELL AvgDlThroughput V14.2/3 G
Bvc bvct1TimeOuts 15008/0 MAX CELL MaxDlThroughput V14.2/3 G/E
Bvc bvcFlowControlRequests 15010/0 CUM CELL idem CDL Attribute V12.4C G/E
Bvc msFlowControlRequests 15010/1 CUM CELL idem CDL Attribute V12.4C G/E
Bvc llcDiscardedPdu 15012/0 CUM CELL idem CDL Attribute V12.4C G/E
Bvc llcDiscardedOctets 15012/1 CUM CELL idem CDL Attribute V12.4C G/E
Bvc msFlushLLRequest 15014/0 CUM CELL idem CDL Attribute V12.4C G/E
Lapd iFramesUp 15023/0 CUM LAPD CsPagingOnCcch V14.2/3 G/E
Lapd iFramesDn 15023/1 CUM LAPD PsPagingOnCcch V14.2/3 G/E
Lapd uiFramesUp 15024/0 CUM LAPD CsPagingOnPacch V14.2/3 G/E
CgiCell upMultiSlotRequests 15028/1 CUM CELL upMultiSlotRequest1 V12.4D G/E
CgiCell upMultiSlotRequests 15028/2 CUM CELL upMultiSlotRequest2 V12.4D G/E
CgiCell upMultiSlotRequests 15028/3 CUM CELL upMultiSlotRequest3 V12.4D G/E
CgiCell upMultiSlotRequests 15028/4 CUM CELL upMultiSlotRequest4 V12.4D G/E
CgiCell upMultiSlotAllocations 15029/1 CUM CELL upTbfGoldSatisfactMore90pCent V14.2/3 G/E
CgiCell upMultiSlotAllocations 15029/2 CUM CELL upTbfGoldSatisfactBet5090pCent V14.2/3 G/E
CDL CDL Attribute Id/SubId Type Class SDO name Created GPRS
Comp. in /
release EDGE
CgiCell upMultiSlotAllocations 15029/3 CUM CELL upTbfGoldSatisfactLess50pCent V14.2/3 G/E
CgiCell upMultiSlotAllocations 15029/4 CUM CELL upTbfGoldRejectedForMinTput V14.2/3 G/E
CgiCell dnMultiSlotRequests 15030/1 CUM CELL dwMultiSlotRequest1 V12.4D G/E
CgiCell dnMultiSlotRequests 15030/2 CUM CELL dwMultiSlotRequest2 V12.4D G/E
CgiCell dnMultiSlotRequests 15030/3 CUM CELL dwMultiSlotRequest3 V12.4D G/E
CgiCell dnMultiSlotRequests 15030/4 CUM CELL dwMultiSlotRequest4 V12.4D G/E
CgiCell dnMultiSlotAllocations 15031/1 CUM CELL FirstDlUnitDataFrame V12.4D G/E
CgiCell dnMultiSlotAllocations 15031/2 CUM CELL dlTBFAllocFailure V12.4D G/E
CgiCell dnMultiSlotAllocations 15031/3 CUM CELL dlTBFRadioFailure V12.4D G/E
CgiCell dnMultiSlotAllocations 15031/4 CUM CELL upTbfSilverSatisfactMore90pCent V14.2/3 G/E
CgiCell fullDuplexTbfEstablishment 15032/0 CUM CELL idem CDL Attribute V12.4C G/E
CgiCell closeEndedUpTbfEstablishment 15032/3 CUM CELL ulsecondPhaseAllocFailure V12.4D G/E
CgiCell upTbfReleases 15033/0 CUM CELL idem CDL Attribute V12.4C G/E
CgiCell dnTbfReleases 15033/1 CUM CELL idem CDL Attribute V12.4C G/E
CgiCell cumulativeTimeUpTbf 15034/0 CUM CELL PDANWithUlReq V12.4D G/E
CgiCell cumulativeTimeDnTbf 15034/1 CUM CELL upTbfSilverSatisfactBet5090pCent V14.2/3 G/E
CgiCell allocatedBlocksUpTbf 15036/0 CUM CELL ulsecondPhaseRadioFailure V12.4D G/E
Tdma localBusy 15038/0 CUM TDMA idem CDL Attribute V12.4C G/E
Tdma configuredTimeslots 15039/0 CUM TDMA cumulativeDnRxLev V14.2/3 G
Tdma cumulativeUpActiveTimeslots 15041/0 CUM TDMA upUserdatablocks V12.4D G
Tdma cumulativeUpTbfPerTimeslots 15043/0 CUM TDMA RequestedRetransmittedData- V12.4D G
BlocksDN
Tdma llcPacketsUp 15045/0 CUM TDMA idem CDL Attribute V12.4C G/E
Tdma llcPacketsDn 15045/1 CUM TDMA idem CDL Attribute V12.4C G/E
Tdma dataBlocksUp 15046/0 CUM TDMA idem CDL Attribute V12.4C G
Tdma dataBlocksDn 15046/1 CUM TDMA idem CDL Attribute V12.4C G
Tdma controlBlocksUp 15047/0 CUM TDMA idem CDL Attribute V12.4C G
Tdma controlBlocksDn 15047/1 CUM TDMA idem CDL Attribute V12.4C G
Tdma invalidBlocksUp 15048/0 CUM TDMA idem CDL Attribute V12.4C G
Tdma invalidProtocolErrorBlocksUp 15048/1 CUM TDMA idem CDL Attribute V12.4C G
Tdma outOfSequenceBlocksUp 15048/2 CUM TDMA idem CDL Attribute V12.4C G
Tdma packetAckNackUp 15049/0 CUM TDMA idem CDL Attribute V12.4C G
Tdma packetAckNackDn 15049/1 CUM TDMA idem CDL Attribute V12.4C G
Tdma totalRetransmissionRequested 15050/0 CUM TDMA idem CDL Attribute V12.4C G
Tdma cumulativeUpRxQual 15051/0 CUM TDMA idem CDL Attribute V12.4C G
Tdma cumulativeDnRxQual 15051/1 CUM TDMA idem CDL Attribute V14.2/3 G
Tdma cumulativeUpRxLev 15052/0 CUM TDMA idem CDL Attribute V14.2/3 G
Tdma nbSamplesUpQuality 15053/0 CUM TDMA idem CDL Attribute V14.2/3 G
Tdma nbSamplesDnQuality 15053/1 CUM TDMA idem CDL Attribute V14.2/3 G
Tdma retransmittedDataBlocksDn 15054/0 CUM TDMA idem CDL Attribute V12.4C G
CDL CDL Attribute Id/SubId Type Class SDO name Created GPRS
Comp. in /
release EDGE
Tdma tbfNormalReleaseUp 15055/0 CUM TDMA idem CDL Attribute V12.4C G/E
Tdma tbfNormalReleaseDn 15055/1 CUM TDMA idem CDL Attribute V12.4C G/E
Tdma noPacketResourceReq 15056/0 CUM TDMA idem CDL Attribute V12.4C G/E
Ccch packetResourceRequest 15056/1 CUM CCCH idem CDL Attribute V12.4C G/E
Tdma lossOfComNN002Max 15057/0 CUM TDMA idem CDL Attribute V12.4C G/E
Tdma lossOfComT3169 15057/1 CUM TDMA idem CDL Attribute V12.4C G/E
Tdma lossOfComNT0001 15057/2 CUM TDMA idem CDL Attribute V12.4C G/E
Tdma lossOfComT3195 15057/3 CUM TDMA idem CDL Attribute V12.4C G/E
Tdma lossOfComT3191 15057/4 CUM TDMA idem CDL Attribute V12.4C G/E
Ccch upTbfImmediateAssignment 15058/0 CUM CCCH idem CDL Attribute V12.4C G/E
Ccch upTbfImmAssigRejectNoPdch 15058/1 CUM CCCH idem CDL Attribute V14.2/3 G/E
Ccch dnTbfImmediateAssignment 15058/2 CUM CCCH idem CDL Attribute V12.4C G/E
Ccch upTbfImmAssigRejectNoTs 15058/3 CUM CCCH dnPipebetween11and22kbps V12.4D G
Ccch upTbfImmAssigRejectNoTbf 15058/4 CUM CCCH dnPipebetween22and33kbps V12.4D G
Ccch channelRequest 15059/0 CUM CCCH channelRequestCcch V12.4C G/E
Ccch deleteIndicationUp 15060/0 CUM CCCH dnPipeGreater33kbps V12.4D G
Ccch deleteIndicationDn 15060/1 CUM CCCH upTbfSilverRejectedForMinTput V14.2/3 G/E
Ccch packetUpAssignment 15061/0 CUM CCCH upPipeless11kbps V12.4D G
Ccch packetDnAssignment 15061/1 CUM CCCH upTbfBronzeSatisfact- V14.2/3 G/E
More90pCent
Ccch upTbfPacketAccessRejectNoPdch 15062/0 CUM CCCH upPipeGreater11kbps V12.4D G
Ccch upTbfPacketAccessRejectNoTs 15062/1 CUM CCCH dnPipeLess11kbps V12.4D G
Ccch upTbfPacketAccessRejectNoTbf 15062/2 CUM CCCH upTbfSilverSatisfactLess50pCent V14.2/3 G/E
Ccch dnTbfPacketAccessRejectNoPdch 15062/3 CUM CCCH upTbfBronzeSatisfact- V14.2/3 G/E
Bet5090pCent
Ccch dnTbfPacketAccessRejectNoTs 15062/4 CUM CCCH upTbfBronzeSatisfactLess50pCent V14.2/3 G/E
Ccch dnTbfPacketAccessRejectNoTbf 15062/5 CUM CCCH upTbfBronzeRejectedForMinTput V14.2/3 G/E
PBlock cpuPBlockUtilAvg 15063/0 AVG PBLK idem CDL Attribute V12.4D G/E
PBlock cpuPBlockUtilMax 15063/2 MAX PBLK idem CDL Attribute V12.4D G/E
Lp cpuUtilAvg 15066/0 AVG LP idem CDL Attribute V12.4C G/E
Lp cpuUtilAvgMin 15066/0 MIN LP idem CDL Attribute V12.4C G/E
Lp cpuUtilAvgMax 15066/0 MAX LP idem CDL Attribute V12.4C G/E
Lp memoryCapacity 15067/0 CUM LP memoryCapacityFastRam V12.4C G/E
Lp memoryCapacity 15067/1 CUM LP memoryCapacityNormalRam V12.4C G/E
Lp memoryCapacity 15067/2 CUM LP memoryCapacitySharedRam V12.4C G/E
Lp memoryUsageAvg 15068/0 AVG LP memoryUsageAvgFastRam V12.4C G/E
Lp memoryUsageAvgMin 15068/0 MIN LP memoryUsageAvgMinFastRam V12.4C G/E
Lp memoryUsageAvgMax 15068/0 MAX LP memoryUsageAvgMaxFastRam V12.4C G/E
Lp memoryUsageAvg 15068/1 AVG LP memoryUsageAvgNormalRam V12.4C G/E
Lp memoryUsageAvgMin 15068/1 MIN LP memoryUsageAvgMinNormalRam V12.4C G/E
CDL CDL Attribute Id/SubId Type Class SDO name Created GPRS
Comp. in /
release EDGE
Lp memoryUsageAvgMax 15068/1 MAX LP memoryUsageAvgMaxNormal- V12.4C G/E
Ram
Lp memoryUsageAvg 15068/2 AVG LP memoryUsageAvgSharedRam V12.4C G/E
Lp memoryUsageAvgMin 15068/2 MIN LP memoryUsageAvgMinSharedRam V12.4C G/E
Lp memoryUsageAvgMax 15068/2 MAX LP memoryUsageAvgMaxSharedRam V12.4C G/E
Lp sharedMsgBlockCapacity 15069/0 CUM LP idem CDL Attribute V12.4C G/E
Lp sharedMsgBlockUsageAvg 15069/1 AVG LP idem CDL Attribute V12.4C G/E
Lp sharedMsgBlockUsageAvgMin 15069/1 MIN LP idem CDL Attribute V12.4C G/E
Lp sharedMsgBlockUsageAvgMax 15069/1 MAX LP idem CDL Attribute V12.4C G/E
Lp localMsgBlockCapacity 15069/2 CUM LP idem CDL Attribute V12.4C G/E
Lp localMsgBlockUsageAvg 15069/3 AVG LP idem CDL Attribute V12.4C G/E
Lp localMsgBlockUsageMin 15069/3 MIN LP idem CDL Attribute V12.4C G/E
Lp localMsgBlockUsageMax 15069/3 MAX LP idem CDL Attribute V12.4C G/E
Framer rxBytes 15070/0 CUM FRAMR idem CDL Attribute V12.4C G/E
Framer txBytes 15070/1 CUM FRAMR idem CDL Attribute V12.4C G/E
Framer rxFrames 15071/0 CUM FRAMR idem CDL Attribute V12.4C G/E
Framer txFrames 15071/1 CUM FRAMR idem CDL Attribute V12.4C G/E
Framer rxTotalLinkUtil 15072/0 CUM FRAMR idem CDL Attribute V12.4C G/E
PcmLink psPaging 15073/0 CUM PCM idem CDL Attribute V14.2/3 G/E
PcmLink csPaging 15073/1 CUM PCM idem CDL Attribute V14.2/3 G/E
CgiCell dyAgprsNbModif 15075/0 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell nonAckUpTbfEstablishment 15075/1 CUM CELL pcuDyAgprsNbTimeslotsCum V15.0 G/E
CgiCell ackUpTbfEstablishment 15075/1 NBS CELL pcuDyAgprsNbTimeslotsNbs V15.0 G/E
CgiCell ackUpTbfEstablishment 15075/1 AVG CELL dyAgprsAvgNbTimeslots V15.0 G/E
CgiCell dyAgprsMinNbTimeslots 15075/2 MIN CELL idem CDL Attribute V14.2/3 G/E
CgiCell dyAgprsMaxNbTimeslots 15075/3 MAX CELL idem CDL Attribute V14.2/3 G/E
CgiCell nonAckDnTbfEstablishment 15076/0 CUM CELL pcuDyAgprsLoadCriterionCum V15.0 G/E
CgiCell ackDnTbfEstablishment 15076/0 NBS CELL pcuDyAgprsLoadCriterionNbs V15.0 G/E
CgiCell ackDnTbfEstablishment 15076/0 AVG CELL dyAgprsAvgLoadCriterion V14.2/3 G/E
CgiCell dyAgprsMaxLoadCriterion 15076/1 MAX CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfGoldSatisfactMore90pCent 15077/0 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfGoldSatisfactBet5090pCent 15077/1 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfGoldSatisfactLess50pCent 15077/2 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfGoldRejectedForMinTput 15077/3 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfSilverSatisfactMore90pCent 15078/0 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfSilverSatisfactBet5090pCent 15078/1 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfSilverSatisfactLess50pCent 15078/2 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfSilverRejectedForMinTput 15078/3 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfBronzeSatisfactMore90pCent 15079/0 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfBronzeSatisfactBet5090pCent 15079/1 CUM CELL idem CDL Attribute V14.2/3 G/E
CDL CDL Attribute Id/SubId Type Class SDO name Created GPRS
Comp. in /
release EDGE
CgiCell dnTbfBronzeSatisfactLess50pCent 15079/2 CUM CELL idem CDL Attribute V14.2/3 G/E
CgiCell dnTbfBronzeRejectedForMinTput 15079/3 CUM CELL idem CDL Attribute V14.2/3 G/E
Tdma pcuEdgeTdma15100s0 15100/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDataBlocksReceivedUp 15101/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnCum8PskMeanBep 15102/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnNbs8PskMeanBep 15102/0 NBS TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnNbs8PskMeanBep 15102/0 AVG TDMA pcuEdgeDnAvg8PskMeanBep V15.0 E
Tdma pcuEdgeDnCumGmskMeanBep 15103/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnNbsGmskMeanBep 15103/0 NBS TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnNbsGmskMeanBep 15103/0 AVG TDMA pcuEdgeDnAvgGmskMeanBep V15.0 E
Tdma pcuEdgeUpCumMeanBep 15104/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeUpNbsMeanBep 15104/0 NBS TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeUpNbsMeanBep 15104/0 AVG TDMA pcuEdgeUpAvgMeanBep V15.0 E
Tdma pcuEdgeTdma15105s0 15105/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeTdma15106s0 15106/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeTdma15107s0 15107/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeTdma15108s0 15108/0 CUM TDMA idem CDL Attribute V15.0 G/E
Tdma pcuEdgeTdma15109s0 15109/0 CUM TDMA idem CDL Attribute V15.0 G/E
CgiCell pcuAgprsMainNbofBlocksDn 15110/0 CUM CELL idem CDL Attribute V15.0 G/E
CgiCell pcuEdgeDowngradedTbf 15111/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeDowngradedTbf 15111/0 NBS CELL pcuEdgeDowngradedTbfNbs V15.0 E
CgiCell pcuEdgeDowngradedTbf 15111/0 AVG CELL pcuEdgeDowngradedTbfAvg V15.0 E
CgiCell pcuEdgeUpCumUsefulDataPerCell 15112/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeUpCumUsefulDataPerCell 15112/0 NBS CELL pcuEdgeUpNbsUsefulDataPerCell V15.0 E
CgiCell pcuEdgeUpCumUsefulDataPerCell 15112/0 AVG CELL pcuEdgeUpAvgUsefulDataPerCell V15.0 E
CgiCell pcuEdgeDnCumUsefulDataPerCell 15113/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeDnCumUsefulDataPerCell 15113/0 NBS CELL pcuEdgeDnNbsUsefulDataPerCell V15.0 E
CgiCell pcuEdgeDnCumUsefulDataPerCell 15113/0 AVG CELL pcuEdgeDnAvgUsefulDataPerCell V15.0 E
CgiCell pcuEdgeCell15114s0 15114/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeCell15115s0 15115/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeCell15116s0 15116/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeCell15117s0 15117/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuDynAgprsJokerCumNbTimeslot 15118/0 CUM CELL idem CDL Attribute V15.0 G/E
CgiCell pcuDynAgprsJokerCumNbTimeslot 15118/0 NBS CELL pcuDynAgprsJokerNbsNbTimes- V15.0 G/E
lot
CgiCell pcuDynAgprsJokerCumNbTimeslot 15118/0 AVG CELL pcuDynAgprsJokerAvgNbTimes- V15.0 G/E
lot
CgiCell pcuDynAgprsJokerMinNbTimeslot 15118/0 MIN CELL idem CDL Attribute V15.0 G/E
CgiCell pcuDynAgprsJokerMaxNbTimeslot 15118/0 MAX CELL idem CDL Attribute V15.0 G/E
CgiCell pcuAgprsJokerNbofBlocksDn 15119/0 CUM CELL idem CDL Attribute V15.0 G/E
CDL CDL Attribute Id/SubId Type Class SDO name Created GPRS
Comp. in /
release EDGE
CgiCell pcuEdgeCell15120s0 15120/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeCell15121s0 15121/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeTbfEstReq 15122/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeUpUsefulDataDurationPerCell 15123/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeDnUsefulDataDurationPerCell 15124/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeCell15125s0 15125/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuEdgeCell15126s0 15126/0 CUM CELL idem CDL Attribute V15.0 E
CgiCell pcuAgprsMainNbofBlocksUp 15127/0 CUM CELL idem CDL Attribute V15.0 G/E
CgiCell pcuAgprsJokerNbofBlocksUp 15128/0 CUM CELL idem CDL Attribute V15.0 G/E
Tdma pcuLackAbisJokerTSCum 15129/0 CUM TDMA idem CDL Attribute V15.0 G/E
Tdma pcuLackAbisJokerTSNbs 15129/0 NBS TDMA idem CDL Attribute V15.0 G/E
Tdma pcuLackAbisJokerTSNbs 15129/0 AVG TDMA pcuLackAbisJokerTSAvg V15.0 G/E
Tdma pcuEdgeDnTransmittedMcs2 15132/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnTransmittedMcs3 15133/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnTransmittedMcs5 15135/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnTransmittedMcs6 15136/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnTransmittedMcs7 15137/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnTransmittedMcs8 15138/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeDnTransmittedMcs9 15139/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeMcs2RequestRetransData- 15142/0 CUM TDMA idem CDL Attribute V15.0 E
BlockDn
Tdma pcuEdgeMcs3RequestRetransData- 15143/0 CUM TDMA idem CDL Attribute V15.0 E
BlockDn
Tdma pcuEdgeMcs5RequestRetransData- 15145/0 CUM TDMA idem CDL Attribute V15.0 E
BlockDn
Tdma pcuEdgeMcs6RequestRetransData- 15146/0 CUM TDMA idem CDL Attribute V15.0 E
BlockDn
Tdma pcuEdgeMcs7RequestRetransData- 15147/0 CUM TDMA idem CDL Attribute V15.0 E
BlockDn
Tdma pcuEdgeMcs8RequestRetransData- 15148/0 CUM TDMA idem CDL Attribute V15.0 E
BlockDn
Tdma pcuEdgeMcs9RequestRetransData- 15149/0 CUM TDMA idem CDL Attribute V15.0 E
BlockDn
Tdma pcuEdgeLADnTargetedTransmit- 15152/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs2
Tdma pcuEdgeLADnTargetedTransmit- 15153/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs3
Tdma pcuEdgeLADnTargetedTransmit- 15155/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs5
Tdma pcuEdgeLADnTargetedTransmit- 15156/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs6
Tdma pcuEdgeLADnTargetedTransmit- 15157/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs7
CDL CDL Attribute Id/SubId Type Class SDO name Created GPRS
Comp. in /
release EDGE
Tdma pcuEdgeLADnTargetedTransmit- 15158/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs8
Tdma pcuEdgeLADnTargetedTransmit- 15159/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs9
Tdma pcuEdgeUpTransmittedMcs2 15162/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeUpTransmittedMcs3 15163/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeUpTransmittedMcs5 15165/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeUpTransmittedMcs6 15166/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeUpTransmittedMcs7 15167/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeUpTransmittedMcs8 15168/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeUpTransmittedMcs9 15169/0 CUM TDMA idem CDL Attribute V15.0 E
Tdma pcuEdgeMcs2RequestRetransData- 15172/0 CUM TDMA idem CDL Attribute V15.0 E
BlockUp
Tdma pcuEdgeMcs3RequestRetransData- 15173/0 CUM TDMA idem CDL Attribute V15.0 E
BlockUp
Tdma pcuEdgeMcs5RequestRetransData- 15175/0 CUM TDMA idem CDL Attribute V15.0 E
BlockUp
Tdma pcuEdgeMcs6RequestRetransData- 15176/0 CUM TDMA idem CDL Attribute V15.0 E
BlockUp
Tdma pcuEdgeMcs7RequestRetransData- 15177/0 CUM TDMA idem CDL Attribute V15.0 E
BlockUp
Tdma pcuEdgeMcs8RequestRetransData- 15178/0 CUM TDMA idem CDL Attribute V15.0 E
BlockUp
Tdma pcuEdgeMcs9RequestRetransData- 15179/0 CUM TDMA idem CDL Attribute V15.0 E
BlockUp
Tdma pcuEdgeLAUpTargetedTransmit- 15182/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs2
Tdma pcuEdgeLAUpTargetedTransmit- 15183/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs3
Tdma pcuEdgeLAUpTargetedTransmit- 15185/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs5
Tdma pcuEdgeLAUpTargetedTransmit- 15186/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs6
Tdma pcuEdgeLAUpTargetedTransmit- 15187/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs7
Tdma pcuEdgeLAUpTargetedTransmit- 15188/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs8
Tdma pcuEdgeLAUpTargetedTransmit- 15189/0 CUM TDMA idem CDL Attribute V15.0 E
tedMcs9
Ccch pcuChannelRequestOnePhase 15190/0 CUM CCCH idem CDL Attribute V15.0 G/E
Ccch pcuUpTbfImmediateAssignmentOne- 15191/0 CUM CCCH idem CDL Attribute V15.0 G/E
Phase
Ccch pcuContentionFailureOnePhase 15192/0 CUM CCCH idem CDL Attribute V15.0 G/E
CgiCell pcuUpThroughputCum 15193/0 CUM CELL idem CDL Attribute V15.0 G
CgiCell pcuUpThroughputNbs 15193/0 NBS CELL idem CDL Attribute V15.0 G
CDL CDL Attribute Id/SubId Type Class SDO name Created GPRS
Comp. in /
release EDGE
15193/0 AVG CELL pcuUpThroughputAvg V15.0 G
CgiCell pcuUpPipeGreater22kbps 15194/0 CUM CELL idem CDL Attribute V15.0 G
CgiCell pcuDnPreEstWithLLCFrameTrans- 15195/0 CUM CELL idem CDL Attribute V15.0 G/E
mitted
The throughput counters and the satisfaction rate counters are computed as follow.
For each pipe (set of radio resources allocated to a MS), the following counters are
defined :
dnNbDataBytes: cumulative number of bytes in downlink RLC data block
received on the pipe
dnVerboseTime: cumulative time the PCU is ready to transmit downlink RLC
data blocks on the pipe (this excludes for instance MS reaction times after a
resource assignment, keep alive duration, ...)
upNbDataBytes: cumulative number of bytes in uplink RLC data blocks
transmitted on the pipe
upVerboseTime: cumulative time the PCU is ready to receive uplink RLC data
blocks on the pipe (this excludes for instance MS reaction times after a resource
assignment)
On pipe closure (and if <direction>VerboseTime is not null), for both directions the
following actions are done:
Compute the throughput as follow:
• <direction>Throughput=<direction>NbDataByte <direction>VerboseTime
· Increments the right <direction> throughput counter corresponding to the limits
including the <direction>Throughput value
· Compute the satisfaction rate as follow:
• <direction>SatisfactionRate=<direction>Throughput/<direction>PeakThro
ughput
· Increments the right <direction> satisfaction rate counter corresponding to the
limits including the <direction>SatisfactionRate value
A pipe closure occurs in the following cases:
at a normal or abnormal release of a half duplex transfer
at an abonormal release of a full duplex transfer
at transitions from half to full duplex transfer, in this case a new pipe is created
at allocation of new resources (after a TS pre--emption for instance), in this case a
new pipe is created
Note that the pipe is not necessary closed at transitions from full to half duplex
transfer.
Test Method:
Test Results:
SGSN sends a Paging Command which is broadcast over the whole routing area.
It triggers an uplink TBF establishment from the mobile with the signalling profile
parameters (UL signaling profile). The mobile is then located thanks to the empty
LLC frame transmitted to the SGSN.
PCU establishes a downlink TBF that will allow to transmit the ping request to the
client: the profile parameters received from SGSN (DL traffic profile) are then used.
Once the ping request has been received by the client, an uplink TBF is established
to transmit the ping response: the profile parameters received from the MS (UL
traffic profile) are used. Finally both TBF end.
Note: The traffic profile used to establish the downlink TBF depends on the
SGSN implementation.
Counter Incrementations:
1st Case: DL traffic profile ¸ UL traffic profile and DL traffic profile ¸ UL
signaling profile:
• UpPipeGreater11kbps +3
• dnPipeBetween22and33kbps +2
2nd Case: DL traffic profile = UL traffic profile and DL traffic profile ¸ UL
signaling profile:
• UpPipeGreater11kbps +3
• dnPipeBetween22and33kbps +1
3rd Case: DL traffic profile ¸ UL traffic profile and DL traffic profile = UL
signaling profile:
• UpPipeGreater11kbps +2
• dnPipeBetween22and33kbps +2
5 COUNTER DESCRIPTION
5.1 Dictionary presentation
Reminder
By definition, a raw counter contains raw measurements taken by the observed
entity whereas a synthetic counter contains the processed results calculated by the
OMC--R from raw measurements.
BSS temporary, permanent md, and permanent manager observations only use raw
counters.
The following fields describe each counter: Number, Title, Name Q3, Feature,
Object, Function, Formula (synthetic counter), Event (raw counter), Type, Class
(raw permanent bsc counters), Source, Precise incrementation conditions,
Exception conditions, Dataflows.
5.1.4.1 Resources
Allocation
Deallocation
5.1.4.3 Handover
Handover required
Handover requests
Executed handover
Successful handover
Name Q3 Location
abisLevel1ErrorsBadFrame<xx> LAPD--<xx>
Function : number of “errored frame” errors detected by Level 1
Event : number of incorrect frames received
Type : raw permanent
Class : Abis interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
l
1084/3 Number of LAPD Level 1 errors: CRC error
Name Q3 : abisLevel1ErrorsCrcError<xx>
Object : bsc
Location :
Name Q3 Location
abisLevel1ErrorsCrcError<xx> LAPD--<xx>
Function : number of “CRC error” errors detected by Level 1
Event : receipt of an indication that the frame is received with a wrong CRC
Type : raw permanent
Class : Abis interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
l
1084/4 Number of LAPD Level 1 errors: Loss of alignment
Name Q3 : abisLevel1ErrorsLostAlign<xx>
Object : bsc
Location :
Name Q3 Location
abisLevel1ErrorsLostAlign<xx> LAPD--<xx>
Function : number of “loss of frame alignment” errors detected by Level 1
Event : receipt of an indication that the alignment is lost
Type : raw permanent
Class : Abis interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
l
1086 Number of GPRS RACHs rejected due to SICD<x> board
overload
Name Q3 : gprsRachRejectedSicd<x>.....for x = 0 to 9
Object : bsc
Location :
Name Q3 Location
gprsRachRejectedSicd<x> SICD--<x>
Function : Number of GPRS RACHs rejected due to SICD<x> board overload
l
1087 Number of GPRS IMMEDIATE ASSIGNMENT messages
rejected due to SICD<x> board overload
Name Q3 : gprsImmAssRejectedSicd<x>.....for x = 0 to 9
Object : bsc
Location :
Name Q3 Location
gprsImmAssRejectedSicd<x> SICD--<x>
l
1088 Number of GPRS PAGING messages rejected due to SICD<x>
board overload
Name Q3 : gprsPagingRejectedSicd<x>.....for x = 0 to 9
Object : bsc
Location :
Name Q3 Location
gprsPagingRejectedSicd<x> SICD--<x>
l
1114 Average time of PCM unavailability
Name Q3 : pcmUnavailabilityMoy . . Average PCM unavailability time
pcmUnavailabilityMax . . Max PCM unavailability time
pcmUnavailabilityCum . . Total PCM unavailability time
pcmUnavailabilityEch . . . Number of samples
Object : pcmCircuit
Function : average (= total time divided by number of samples) and maximum
time of BSS external PCM unavailability in the observation period,
expressed in milliseconds
Event : PCM operational state changes (operationalState attribute):
leave “enabled” state: set timer
l
1121 Number of passive chain update messages
Name Q3 : chainStandByUpdate
Object : bsc
Function : number of messages sent from the active to the BSC passive chain
Event : transmission of a message to the BSC passive chain
Type : raw permanent
Class : BSC equipment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
l
1122 Number of passive chain response messages
Name Q3 : chainStandByResponse
Object : bsc
Function : number of response messages sent from the passive to the BSC active
chain
Event : reception of a response message from the BSC passive chain
Type : raw permanent
Class : BSC equipment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
l
1300 Number of I frames sent
Name Q3 : omcOutputIFrame
Object : bsc
Function : number of I (Information) frames sent by the BSC (local X.25
Level 2) to the OMC--R agent (remote X.25 Level 2)
Event : transmission of an I frame on the X.25 link by the BSC
Type : raw permanent
Class : BSS/OMC--R link
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Call or
Packet Calls.
Note : V12 counter
l
1301 Number of I frames received
Name Q3 : omcInputIFrame
Object : bsc
Function : number of I (Information) frames received by the BSC (local X.25
Level 2)
Event : receipt of an I frame on the X.25 link by the BSC
Type : raw permanent
Class : BSS/OMC--R link
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Call or
Packet Calls.
l
1302 Number of repeated I frames sent
Name Q3 : omcOutputRepeatedIFrame
Object : bsc
Function : number of repeated I (Information) frames sent by the BSC (local
X.25 Level 2) to the OMC--R agent (remote X.25 Level 2)
Event : transmission of a repeated I frame on the X.25 link by the BSC
Type : raw permanent
Class : BSS/OMC--R link
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Call or
Packet Calls.
l
1303 Number of repeated I frames received
Name Q3 : omcInputRepeatedIFrame
Object : bsc
Function : number of repeated I (Information) frames received by the BSC (local
X.25 Level 2)
Event : receipt of a repeated I frame on the X.25 link by the BSC
Type : raw permanent
Class : BSS/OMC--R link
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Call or
Packet Calls.
l
1304 Number of RNR frames sent
Name Q3 : omcOutputRnrFrame
Object : bsc
Function : number of RNR (Received Non Ready) frames sent by the BSC (local
X.25 Level 2) to the OMC--R agent (remote X.25 Level 2)
Event : transmission of a RNR frame on the X.25 link by the BSC
Type : raw permanent
Class : BSS/OMC--R link
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Call or
Packet Calls.
l
1305 Number of RNR frames received
Name Q3 : omcInputRnrFrame
Object : bsc
Function : number of RNR (Received Non Ready) frames received by the BSC
(local X.25 Level 2)
Event : receipt of a RNR frame on the X.25 link by the BSC
Type : raw permanent
Class : BSS/OMC--R link
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Call or
Packet Calls.
l
1400 Average load of CPUM board
Name Q3 : prLoadCpumMoy
prLoadCpumMax . . . . . . . . . . . . . . Maximum load of the CPUM
board
prLoadCpumCum . . . . . . . . . . . . . Total load of the CPUM board
prLoadCpumEch . . . . . . . . . . . . . . Number of samples
Object : bsc
Location :
Name Q3 Location
prLoadCpumMoy/Max/Cum/Ech CPUM--0
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
This counter gives the real load of the processor. And the load of a
BSC processor is impacted by GPRS messages treated by this
processor.
l
1400 Average load of CPUE x board
Name Q3 : prLoadCpueMoy
prLoadCpue1Moy
prLoadCpue2Moy
prLoadCpueMax . . . . . . . . Maximum load of the CPUE 0 board
prLoadCpue1Max . . . . . . . Maximum load of the CPUE 1 board
prLoadCpue2Max . . . . . . . Maximum load of the CPUE 2 board
prLoadCpueCum . . . . . . . . Total load of the CPUE 0 board
prLoadCpue1Cum . . . . . . . Total load of the CPUE 1 board
prLoadCpue2Cum . . . . . . . Total load of the CPUE 2 board
prLoadCpueEch . . . . . . . . . Number of samples
prLoadCpue1Ech . . . . . . . . Number of samples
prLoadCpue2Ech . . . . . . . . Number of samples
Object : bsc
Location :
Name Q3 Location
prLoadCpueMoy/Max/Cum/Ech CPUE--0
prLoadCpue1Moy/Max/Cum/Ech CPUE--1
prLoadCpue2Moy/Max/Cum/Ech CPUE--2
Name Q3 Location
prLoadSicd<x>Moy/Max/Cum/Ech SICD--<x>
1755/0 Number of faults relating to the PCM with cause external PCM
fault
Name Q3 : pcmFaultExternal
Object : pcmCircuit
Function : number of faults relating to PCM
Event : external PCM fault
Type : raw permanent
Class : PCM link
Source : recorded by the BSC
l
1755/1 Number of faults relating to the PCM with cause internal fault
Name Q3 : pcmFaultInternal
Object : pcmCircuit
Function : number of faults relating to PCM
Event : internal PCM fault
Type : raw permanent
Class : PCM link
Source : recorded by the BSC
l
1755/2 Number of faults relating to the PCM with cause DDTI/SLTI
board fault
Name Q3 : pcmFaultDDTIBoard
Object : pcmCircuit
Function : number of faults relating to PCM
Event : DDTI/SLTI board fault
Type : raw permanent
Class : PCM link
Source : recorded by the BSC
l
1755/3 Number of faults relating to the PCM with cause taken out of
service for an O&M reason
Name Q3 : pcmFaultOutOfService
Object : pcmCircuit
Function : number of faults relating to PCM
Event : taken out of service for an O&M reason
Type : raw permanent
Class : PCM link
Source : recorded by the BSC
l
1803/0 Number of rejected calls on paging requests due to overload
Name Q3 : cgOverloadRejectedOpPageReqCg0
cgOverloadRejectedOpPageReqCg1
cgOverloadRejectedOpPageReqCg2
Object : bsc
Location :
Q3 Name Location
cgOverloadRejectedOpPageReqCg0 CPUE--0
cgOverloadRejectedOpPageReqCg1 CPUE--1
cgOverloadRejectedOpPageReqCg2 CPUE--2
l
1803/1 Number of rejected calls on channel requests due to overload
Name Q3 : cgOverloadRejectedOpChannelReqCg0
cgOverloadRejectedOpChannelReqCg1
cgOverloadRejectedOpChannelReqCg2
Object : bsc
Location :
Q3 Name Location
cgOverloadRejectedOpChannelReqCg0 CPUE--0
cgOverloadRejectedOpChannelReqCg1 CPUE--1
cgOverloadRejectedOpChannelReqCg2 CPUE--2
l
1803/2 Number of rejected calls on establish indication due to overload
Name Q3 : cgOverloadRejectedOpEstablishIndCg0
cgOverloadRejectedOpEstablishIndCg1
cgOverloadRejectedOpEstablishIndCg2
Object : bsc
Location :
Q3 Name Location
cgOverloadRejectedOpEstablishIndCg0 CPUE--0
cgOverloadRejectedOpEstablishIndCg1 CPUE--1
cgOverloadRejectedOpEstablishIndCg2 CPUE--2
3
1803/3 Number of rejected calls on handover requests due to overload
Name Q3 : cgOverloadRejectedOpHoReqCg0
cgOverloadRejectedOpHoReqCg1
cgOverloadRejectedOpHoReqCg2
Object : bsc
Location :
Q3 Name Location
cgOverloadRejectedOpHoReqCg0 CPUE--0
cgOverloadRejectedOpHoReqCg1 CPUE--1
cgOverloadRejectedOpHoReqCg2 CPUE--2
3
1803/4 Number of rejections on paging requests due to an
overloaded cell
Name Q3 : cgOverloadRejectedOpPageReqBtsCg0
cgOverloadRejectedOpPageReqBtsCg1
cgOverloadRejectedOpPageReqBtsCg2
Object : bsc
Location :
Q3 Name Location
cgOverloadRejectedOpPageReqBtsCg0 CPUE--0
cgOverloadRejectedOpPageReqBtsCg1 CPUE--1
cgOverloadRejectedOpPageReqBtsCg2 CPUE--2
3
1803/5 number of rejected sms--cb messages due to overload situation
Name Q3 : cgOverloadRejectedOpSmsCbCg0
cgOverloadRejectedOpSmsCbCg1
cgOverloadRejectedOpSmsCbCg2
Object : bsc
Location :
Q3 Name Location
cgOverloadRejectedOpSmsCbCg0 CPUE--0
cgOverloadRejectedOpSmsCbCg1 CPUE--1
cgOverloadRejectedOpSmsCbCg2 CPUE--2
l
1834 Number of rejected calls on paging requests due to SICD<x>
board overload
Name Q3 : lapdOverloadRejectedOpSicd<x>.....for x = 0 to 9
Object : bsc
Location :
Name Q3 Location
lapdOverloadRejectedOpSicd<x> SICD--<x>
Function : Number of channel requests rejected due to SICD<x> board overload
Event : receipt of a channel request message
Type : raw permanent
Class : equipment
Source : recorded by the BSC
Feature : Overload defense mechanism based on real load (FM877-- V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
In case of rejection, no distinction is made between CHANNEL
REQUESTS messages dedicated to Circuit Call or Packet Calls.
l
1835 Synthetic load on CPUM, CPUE<x>, SICD<y> board
Name Q3 : cardSynthLoadCpumMoy
cardSynthLoadCpumMax
cardSynthLoadCpumCum
cardSynthLoadCpumEch
cardSynthLoadCpue<x>Moy.....for x = 0 to 2
cardSynthLoadCpue<x>Max
cardSynthLoadCpue<x>Cum
cardSynthLoadCpue<x>Ech
cardSynthLoadSicd<y>Moy.....for y = 0 to 9
cardSynthLoadSicd<y>Max
cardSynthLoadSicd<y>Cum
cardSynthLoadSicd<y>Ech
Object : bsc
Location :
Name Q3 Location
cardSynthLoadCpumMoy/Max/Cum/Ech CPUM--0
cardSynthLoadCpue<x>Moy/Max/Cum/Ech CPUE--<x>
cardSynthLoadSicd<y>Moy/Max/Cum/Ech SICD--<y>
5.3.1 Raw permanent BSS counters (BSC 3000) (from 1065/1 to 3008/3)
l
1065/1 Number of outgoing intra BSS handover execution attempts
from the cell for directed retry reason
Name Q3 : hoExecutionOutgoingIntraBssForDirectedRetry
Object : bts
Function : Number of outgoing intra BSS handover execution attempts from the
cell for directed retry reason
Event : Transmission of HANDOVER_COMMAND message (ABIS
message)
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1066/1 Number of outgoing inter BSS handover execution attempts from
the cell for directed retry reason
Name Q3 : hoExecutionOutgoingInterBssForDirectedRetry
Object : bts
Function : Number of outgoing inter BSS handover execution attempts from the
cell for directed retry reason
Event : Receipt of HANDOVER_COMMAND message from the MSC
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1067/1 Number of successful outgoing intra BSS handover from the cell
for directed retry reason
Name Q3 : hoSuccessOutgoingIntraBssForDirectedRetry
Object : bts
Function : Number of successful outgoing intra BSS handover from the cell for
directed retry reason
Event : Receipt of HANDOVER_COMPLETE message from the mobile
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1068/1 Number of successful outgoing inter BSS handover from the cell
for directed retry reason
Name Q3 : hoSuccessOutgoingInterBssForDirectedRetry
Object : bts
Function : Number of successful outgoing inter BSS handover from the cell for
directed retry reason
Event : Receipt of CLEAR_COMMAND message from the MSC with the
handover cause set to “handover successful”
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Note : For the number of successful outgoing inter handovers on TCH after
first attempt see counter 1078.
l
1164/33 Number of releases while the communication is in “traffic” phase.
Name Q3 : trafficReleaseTbcEdge
Object : bts
Function : number of releases while the communication is in “traffic” phase
Event : TDMA removal due to a EDGE TRX/TDMA optimization
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1206/1 Number of handovers or assignments in which the initial request
in EFR speech algorithm is degraded into FR speech algorithm
for AMR calls
Name Q3 : amrFrSpeechAlgoFallBack
Object : bsc
Function : Number of handovers or assignments in which the initial request in
EFR speech algorithm is degraded into FR speech algorithm for AMR
calls
Event : This counter is incremented on the reception of an
ASSIGN_REQUEST or an HANDOVER_REQUEST with a CIC
incompatible with the speech coding algorithm. In the case where the
BSC has got CIC bearing EFR and other CIC not bearing EFR and if
all CIC bearing EFR are already allocated
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Note : V14 counter
l
1507/0 Number of rejected paging requests due to overload situation
Name Q3 : e3OverloadRejectedOpPagingReq
Object : bsc
Function : number of rejected paging requests due to overload situation (this
counter is incremented if the local card is overloaded or the operation
family named paging request is overloaded)
Event : receipt of a paging request when at least one card concerning this
operation is in an overload situation
Precise
incrementation conditions :
CS--Paging and PS--Paging messages dropped in case of overload are
counted by this counter.
Type : raw permanent
Class : equipment
Source : recorded by the BSC
Note : V14 counter
l
1507/1 Number of rejected channel requests due to overload situation
Name Q3 : e3OverloadRejectedOpChannelReq
Object : bsc
Function : number of rejected channel requests due to overload situation
Event : receipt of a channel request when at least one card concerning this
operation is in an overload situation
Type : raw permanent
Class : equipment
Source : recorded by the BSC
Note : V14 counter
l
1507/2 Number of rejected establish indication messages due to overload
situation
Name Q3 : e3OverloadRejectedOpEstablishInd
Object : bsc
Function : number of rejected establish indication messages due to overload
situation
Precise
incrementation conditions :
CS--Paging and PS--Paging messages dropped in case of overload are
counted by this counter.
Type : raw permanent
Class : equipment
Source : recorded by the BSC
Note : V14 counter
l
1507/5 number of rejected sms--cb messages due to overload situation.
Name Q3 : e3OverloadRejectedOpSmsCb
Object : bsc
Function : number of rejected sms--cb message caused by an overloaded cell
Event : receipt of a sms--cb message rejection caused by an overloaded cell
when at least one card concerning this operation is in an overload
situation (for the same originating sms--cb message, this counter will
be increased each time the target cell is overloaded)
Type : raw permanent
Class : equipment
Source : recorded by the BSC
Note : V15.1R counter
l
1508/0 number of paging requests filtered by the BSC 3000
Name Q3 : pagingFilteredByBsc
Object : bsc
Function : Number of paging requests filtered by the A interface filter in the BSC
3000 independently of the overload condition (which lead to peg the
1506 and 1507 counters). Only paging for Circuit Service are
concerned.
Event : paging request message is filtered by the A interface filter in the BSC
Type : raw permanent
Source : recorded by the BSC
Feature : 29479 Paging capacity increase - UI mode-- BSC 3000
l
1610/1 Number of half rate TCH allocations
Name Q3 : tchHrAllocatedWps
tchHrAllocatedWpsTrZone
Object : bts/transceiverZone
Function : Cumulative number of half rate TCH allocations.
Event : Allocation of a half rate TCH (including PDTCH) for a WPS call.
Type : raw permanent
Feature : WPS BSS2G and 3000 public access bandwidth protection (22465)
Source : recorded by the BSC
l
1612/1 Average and maximum number of half rate Primo allocations
Name Q3 : tchHrAveragedUsedWpsTrZoneMoy
tchHrAveragedUsedWpsTrZoneMax
tchHrAveragedUsedWpsTrZoneEch
tchHrAveragedUsedWpsTrZoneCum
Object : bts/transceiverZone
Function : Average and maximum number of WPS half rate TCH (including
PDTCH) allocations
Event : Allocation/de--allocation of a half rate TCH
Type : raw permanent
Class : allocation
Feature : 3000 public access bandwidth protection (22465)
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by CCT (Circuit
calls on TCH channel), but not by CCP (Circuit Calls on PDTCH
preempted to make a TCH channel). This is because this counter is
related to configured (static) TCH/FR channel. This counter is
pegged on the traffic channel allocation for a WPS call if the WPS
Management flag is enabled. This counter is pegged on the traffic
channel de--allocation for a call initiated as a WPS call.
l
1817/0 Average, maximum, mimium, and total number of half rate
TCH allocations
Name Q3 : burstToTransmit
Object : bts
Function :
Event : allocation/de--allocation of a half rate TCH.
Type : raw permanent
Class : setup
Source : recorded by the BSC
l
2000/0 Number of PDTCH available and preempted for EDGE services
Name Q3 : totalNumberOfEdgeTsCum
totalNumberOfEdgeTsTrZoneCum
totalNumberOfEdgeTsEch
totalNumberOfEdgeTsTrZoneEch
totalNumberOfEdgeTsMax
totalNumberOfEdgeTsTrZoneMax
totalNumberOfEdgeTsMoy
totalNumberOfEdgeTsTrZoneMoy
Object : bts/transceiverZone
Function : Maximum, average, and cumulative number of available PDTCH for
EDGE (all configured PDTCH not pre--empted for circuit calls and
available for EDGE)
Event : PDTCH configuration or preemption/release of the EDGE channel by
the BSC.
Type : LOAD
Feature : 19174 (EDGE dynamic Abis and Agprs backhaul)
Source : TBD
Note : V15 counter
l
2000/1 Number of PDTCH available and preempted for EDGE services
Name Q3 : allocatedEdgeTsMoy
allocatedEdgeTsMax
allocatedEdgeTsCum
allocatedEdgeTsEch
allocatedEdgeTsTrZoneMoy
allocatedEdgeTsTrZoneMax
allocatedEdgeTsTrZoneCum
allocatedEdgeTsTrZoneEch
Object : bts/transceiverZone
Function : Maximum, average, and cumulative number of available PDTCH for
EDGE allocated to the PCU
Event : PDTCH configuration or preemption/release of the EDGE channel by
the BSC.
Type : LOAD
Feature : 19174 (EDGE dynamic Abis and Agprs backhaul)
Source : TBD
Note : V15 counter
l
2000/2 Number of PDTCH available and preempted for EDGE services
Name Q3 : preemptedEdgeTsCum
preemptedEdgeTsTrZoneCum
preemptedEdgeTsMax
preemptedEdgeTsTrZoneMax
preemptedEdgeTsMoy
preemptedEdgeTsTrZoneMoy
preemptedEdgeTsEch
preemptedEdgeTsTrZoneEch
Object : bts/transceiverZone
Function : Minimum, maximum, average, and cumulative number of available
PDTCH for EDGE services preempted by circuit calls
Event : PDTCH configuration or preemption/release of the EDGE channel by
the BSC.
Type : LOAD
Feature : 19174 (EDGE dynamic Abis and Agprs backhaul)
Source : TBD
Note : V15 counter
l
2001 Number of joker DS0 TS allocated on the Abis interface.
Name Q3 : allocatedAbisJokerTSEdgeCum
allocatedAbisJokerTSEdgeTrZoneCum
allocatedAbisJokerTSEdgeEch
allocatedAbisJokerTSEdgeTrZoneEch
allocatedAbisJokerTSEdgeMax
allocatedAbisJokerTSEdgeTrZoneMax
allocatedAbisJokerTSEdgeMoy
allocatedAbisJokerTSEdgeTrZoneMoy
allocatedAbisJokerTS
Object : bts/transceiverZone
Function : Minimum, maximum, average, and cumulative number of joker DS0
TS allocated on the Abis interface
Event : Joker (dis) configuration at TDMA configuration (or removal).
Type : LOAD
Feature : 19174 (EDGE dynamic Abis and Agprs backhaul)
Source : TBD
Note : V15 counter
l
2002/0 Number of PDTCH available and preempted for EDGE services
Name Q3 : totalNumberOfEdgeTsCellMoy
totalNumberOfEdgeTsCellMax
totalNumberOfEdgeTsCellCum
totalNumberOfEdgeTsCellEch
Object : bts
Function : Maximum, average, and cumulative number of available PDTCH for
EDGE (all configured PDTCH not pre--empted for circuit calls and
available for EDGE)
Event : PDTCH configuration or preemption/release of the EDGE channel by
the BSC.
Type : LOAD
Feature : 19174 (EDGE dynamic Abis and Agprs backhaul)
Source : recorded by the BSC
Note : V15 counter
l
2002/1 Number of PDTCH available and preempted for EDGE services
Name Q3 : allocatedEdgeTsCellMoy
allocatedEdgeTsCellMax
allocatedEdgeTsCellCum
allocatedEdgeTsCellEch
Object : bts
Function : Maximum, average, and cumulative number of available PDTCH for
EDGE allocated to the PCU
Event : PDTCH configuration or preemption/release of the EDGE channel by
the BSC.
Type : LOAD
Feature : 19174 (EDGE dynamic Abis and Agprs backhaul)
Source : recorded by the BSC
Note : V15 counter
l
2002/2 Number of PDTCH available and preempted for EDGE services
Name Q3 : preemptedEdgeTsCellMoy
preemptedEdgeTsCellMax
preemptedEdgeTsCellCum
preemptedEdgeTsCellEch
Object : bts
Function : Minimum, maximum, average, and cumulative number of available
PDTCH for EDGE services preempted by circuit calls
Event : PDTCH configuration or preemption/release of the EDGE channel by
the BSC.
Type : LOAD
Feature : 19174 (EDGE dynamic Abis and Agprs backhaul)
Source : recorded by the BSC
Note : V15 counter
2072 Number of PCU MS suspend nack received by the BSC from the
PCU
Name Q3 : agprsSuspendNack
Object : bsc
Function : Number of PCU MS suspend nack received by the BSC from the
PCU.
Event : The BSC receives a suspend nack for a communication.
Type : raw permanent
Class : GPRS/EDGE
Source : recorded by the BSC
Feature : 25155 GPRS / EDGE Suspend and Resume
Precise
incrementation conditions :
In case of multiple messages relative to the same communication,
the counter is incremented only one time per communication.
Data flows : Refer to Chapter 2
GPRS / EDGE Suspend procedure with RAU message (failure
case)
Note : V15 counter
2073 number of PCU MS resume messages sent by the BSC to the PCU
Name Q3 : agprsResumeRequest
Object : bsc
Function : Number of PCU MS resume messages sent by the BSC to the PCU.
Event : The BSC sends a resume message for a communication.
Type : raw permanent
Class : GPRS/EDGE
Source : recorded by the BSC
Feature : 25155 GPRS / EDGE Suspend and Resume
Data flows : Refer to Chapter 2
GPRS / EDGE Suspend procedure with Resume message (nominal
procedure)
GPRS / EDGE Suspend procedure with Resume message (failure
case)
Note : V15 counter
2074 Number of PCU MS resume nack received by the BSC from the
PCU
Name Q3 : agprsResumeNack
Object : bsc
Function : Number of PCU MS resume nack received by the BSC from the PCU.
Event : The BSC receives a resume nack for a communication.
Type : raw permanent
Class : GPRS/EDGE
Source : recorded by the BSC
Feature : 25155 GPRS / EDGE Suspend and Resume
Data flows : Refer to Chapter 2
GPRS / EDGE Suspend procedure with Resume message (failure
case)
Note : V15 counter
3000/0 load of a OMU processor inside the Control Node of the sys-
tem: SBC
Name Q3 : prLoadCne3OmuSbcMoy
prLoadCne3OmuSbcMax
prLoadCne3OmuSbcCum
prLoadCne3OmuSbcEch
Object : omu
Function : Load of a given OMU processor inside the Control Node of the system
Event : Core system internal counting
Type : raw permanent
Class : BSC equipment
Source : recorded by BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit Calls on TCH channels
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com Packets on PDTCH channel
Note : Each counter has a value between 0 and 100 (the value 100 represents
a 100% load).
3001/0 Load of a given TMU processor inside the Control Node of the
system: SBC
Name Q3 : prLoadCne3TmuSbcMoy
prLoadCne3TmuSbcMax
prLoadCne3TmuSbcCum
prLoadCne3TmuSbcEch
Object : tmu
Function : Load of a given TMU processor inside the Control Node of the system
Event : Core system internal counting
Type : raw permanent
Class : BSC equipment
Source : recorded by BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit Calls on TCH channels
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com Packets on PDTCH channel
Note : V13.1 counter
Each counter has a value between 0 and 100 (the value 100 represents
a 100% load).
3001/2 Load of a given TMU processor inside the Control Node of the
system: PMC
Name Q3 : prLoadCne3TmuPmcMoy
prLoadCne3TmuPmcMax
prLoadCne3TmuPmcCum
prLoadCne3TmuPmcEch
Object : tmu
Function : Load of a given TMU processor inside the Control Node of the
system: PMC
Event : Core system internal counting
Type : raw permanent
Class : BSC equipment
Source : recorded by BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit Calls on TCH channels
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com Packets on PDTCH channel
Note : V13.1 counter
This counter has a value between 0 and 100 (the value 100 represents
a 100% load).
The PMC may be an option. In this case it has no significant value and
the result will be a succession “***…***” at the OMC level.
If the BSC 3000 is equipped with TMU2 boards, the PMC screening
value of counter 3001/2 is not significant either (because the PMC is
a TMU1 board processor)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit Calls on TCH channels
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com Packets on PDTCH channel
Note : V13.1 counter
This counter has a value between 0 and 100 (the value 100 represents
a 100% load).
3008/0 Disk usage on OMU processor inside the Control Node of the
system: local disk access for write operation
Name Q3 : e3PrDiskCnOmuLdWMoy
e3PrDiskCnOmuLdWMax
e3PrDiskCnOmuLdWCum
e3PrDiskCnOmuLdWEch
Object : omu
Function : Disk usage on OMU processor inside the Control Node of the system:
disk access on local disk for write operation (Kbyte/s)
Event : Core system internal counting
Type : raw permanent
Class : BSC equipment
Source : recorded by BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit Calls on TCH channels
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com Packets on PDTCH channel
Note : V13.1 counter
3008/1 Disk usage on OMU processor inside the Control Node of the
system: local disk access for read operation
Name Q3 : e3PrDiskCnOmuLdRMoy
e3PrDiskCnOmuLdRMax
e3PrDiskCnOmuLdRCum
e3PrDiskCnOmuLdREch
Object : omu
Function : Disk usage on OMU processor inside the Control Node of the system:
disk access on local disk for read operation (Kbyte/s)
Event : Core system internal counting
Type : raw permanent
Class : BSC equipment
Source : recorded by BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit Calls on TCH channels
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com Packets on PDTCH channel
Note : V13.1 counter
3008/2 Disk usage on OMU processor inside the Control Node of the
system: mirror disk access for write operation
Name Q3 : e3PrDiskCnOmuMdWMoy
e3PrDiskCnOmuMdWMax
e3PrDiskCnOmuMdWCum
e3PrDiskCnOmuMdWEch
Object : omu
Function : Disk usage on OMU processor inside the Control Node of the system:
disk access on mirror disk for write operation (Kbyte/s)
Event : Core system internal counting
Type : raw permanent
Class : BSC equipment
Source : recorded by BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit Calls on TCH channels
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com Packets on PDTCH channel
Note : V13.1 counter
3008/3 Disk usage on OMU processor inside the Control Node of the
system: mirror disk access for read operation
Name Q3 : e3PrDiskCnOmuMdRMoy
e3PrDiskCnOmuMdRMax
e3PrDiskCnOmuMdRCum
e3PrDiskCnOmuMdREch
Object : omu
Function : Disk usage on OMU processor inside the Control Node of the system:
disk access on mirror disk for read operation (Kbyte/s)
Event : Core system internal counting
Type : raw permanent
Class : BSC equipment
Source : recorded by BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit Calls on TCH channels
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com Packets on PDTCH channel
Note : V13.1 counter
l
1197/3 Number of channels activated for speech: AMR Full Rate
Algorithm
Name Q3 : channelActivateSpeechAmrFr
Object : bts
Function : number of speech channels using the AMR Full-Rate algorithm,
activated in the cell for the observation period
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “speech”
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1900/0 Number of AMR full rate TCH allocations
Name Q3 : amrFrTchAllocated
amrFrTchAllocatedTrZone
Object : bts/transceiverZone
Function : number of AMR full rate TCH allocations
Event : This counter is incremented when a AMR full rate TCH is allocated
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1901/0 Average and Maximum number of AMR full rate TCH
allocations
Name Q3 : amrFrTchStdAveragedUsedMoy
amrFrTchStdAveragedUsedMax
amrFrTchStdAveragedUsedCum
amrFrTchStdAveragedUsedEch
amrFrTchStdAveragedUsedTrZoneMoy
amrFrTchStdAveragedUsedTrZoneMax
amrFrTchStdAveragedUsedTrZoneCum
amrFrTchStdAveragedUsedTrZoneEch
Object : bts/transceiverZone
Function : Average and Maximum number of AMR full rate TCH allocations
Event : This counter is incremented when an AMR full rate TCH is allocated
or de--allocated
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1902/0 Duration of the AMR full rate TCH connections
Name Q3 : amrFrTchConnectionDurationMoy
amrFrTchConnectionDurationTrZoneMoy
amrFrTchConnectionDurationMax
amrFrTchConnectionDurationTrZoneMax
amrFrTchConnectionDurationCum
amrFrTchConnectionDurationTrZoneCum
amrFrTchConnectionDurationEch
amrFrTchConnectionDurationTrZoneEch
Object : bts/transceiverZone
Function : Duration of the AMR full rate TCH connections. This counter starts at
the beginning of transmission of SACCH blocks, and stops at the end
of SACCH blocks transmission.
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1902/1 Duration of the AMR half rate TCH connections
Name Q3 : amrHrTchConnectionDurationMoy
amrHrTchConnectionDurationTrZoneMoy
amrHrTchConnectionDurationMax
amrHrTchConnectionDurationTrZoneMax
amrHrTchConnectionDurationCum
amrHrTchConnectionDurationTrZoneCum
amrHrTchConnectionDurationEch
amrHrTchConnectionDurationTrZoneEch
Object : bts/transceiverZone
Function : Duration of the AMR half rate TCH connections. This counter starts
at the beginning of transmission of SACCH blocks, and stops at the
end of SACCH blocks transmission.
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1903/0 Number of Successful AMR full rate TCH assignations for any
kind of mobile
Name Q3 : amrFrTchSuccessfullyAssigned
Object : bts
Function : Number of Successful AMR full rate TCH assignations for any kind
of mobile
Event : See function
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1903/1 Number of Successful AMR half rate TCH assignations for any
kind of mobile
Name Q3 : amrHrTchSuccessfullyAssigned
Object : bts
Function : Number of Successful AMR half rate TCH assignations for any kind
of mobile
Event : See function
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1904/0 Number of Failures of the Dedicated Channel Assignment
Procedure for AMR full rate TCH
Name Q3 : amrFrTchAssignFailure
Object : bts
Function : Number of Failures of the Dedicated Channel Assignment Procedure
for AMR full rate TCH
Event : This counter is triggered on reception of an Assign_Fail message on
AMR TCH from the mobile
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1904/1 Number of Failures of the Dedicated Channel Assignment
Procedure for AMR half rate TCH
Name Q3 : amrHrTchAssignFailure
Object : bts
Function : Number of Failures of the Dedicated Channel Assignment Procedure
for AMR half rate TCH
Event : This counter is triggered on reception of an Assign_Fail message on
AMR TCH from the mobile
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1905 Total of the uplink C/I received from the L1m, for a non AMR
channel
Name Q3 : CIUplinkFr
CIUplinkFrTrZone
Object : bts/transceiverZone
Function : Total of the uplink C/I received from the L1m, for a non AMR channel
(i.e. classic TCH and SDCCH)
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1906 Amount of time the downlink power control was running at the
maximum level for the busy full rate AMR TCHs
Name Q3 : downlinkPowerCtrlMaxTchAmrFrCum
downlinkPowerCtrlMaxTchAmrFrEch
downlinkPowerCtrlMaxTchAmrFrMax
downlinkPowerCtrlMaxTchAmrFrMoy
Object : bts
Function : Minimum, maximum, average, and cumulative amount of time the
downlink power control was running at the maximum level for the
busy full rate AMR TCHs
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1907 Amount of time the uplink power control was running at the
maximum level for the busy full rate AMR TCHs
Name Q3 : uplinkPowerCtrlMaxTchAmrFrCum
uplinkPowerCtrlMaxTchAmrFrEch
uplinkPowerCtrlMaxTchAmrFrMax
uplinkPowerCtrlMaxTchAmrFrMoy
Object : bts
Function : Minimum, maximum, average, and cumulative amount of time the
uplink power control was running at the maximum level for the busy
full rate AMR TCHs
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1908 Number of downlink RXLEV received from the L1m for AMR
full rate TCH
Name Q3 : RxLevDownlinkAmrFr
RxLevDownlinkAmrFrTrZone
Object : bts/transceiverZone
Function : Number of downlink RXLEV received from the L1m for AMR full
rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1909 Number of uplink RXLEV received from the L1m for AMR full
rate TCH
Name Q3 : RxLevUplinkAmrFr
RxLevUplinkAmrFrTrZone
Object : bts/transceiverZone
Function : Number of uplink RXLEV received from the L1m for AMR full rate
TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1910 Number of downlink RXQUAL received from the L1m for AMR
full rate TCH
Name Q3 : RxQualDownlinkAmrFr
RxQualDownlinkAmrFrTrZone
Object : bts/transceiverZone
Function : Number of downlink RXQUAL received from the L1m for AMR full
rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1911 Number of uplink RXQUAL received from the L1m for AMR full
rate TCH
Name Q3 : RxQualUplinkAmrFr
RxQualUplinkAmrFrTrZone
Object : bts/transceiverZone
Function : Number of uplink RXQUAL received from the L1m for AMR full
rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1912 Number of MS increment power control ordered by the L1m for
AMR full rate TCH
Name Q3 : msPowerIncControlAmrFr
Object : bts
Function : Number of MS increment power control ordered by the L1m for AMR
full rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1913 Number of MS decrement power control ordered by the L1m for
AMR full rate TCH
Name Q3 : msPowerDecControlAmrFr
Object : bts
Function : Number of MS decrement power control ordered by the L1m for
AMR full rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1914 Number of BS increment power control ordered by the L1m for
AMR full rate TCH
Name Q3 : bsPowerIncControlAmrFr
Object : bts
Function : Number of BS increment power control ordered by the L1m for AMR
full rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1915 Number of BS decrement power control ordered by the L1m for
AMR full rate TCH
Name Q3 : bsPowerDecControlAmrFr
Object : bts
Function : Number of BS decrement power control ordered by the L1m for AMR
full rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1916 Total of the uplink C/I received from the L1m, for AMR full rate
calls
Name Q3 : CIUplinkAmrFr
CIUplinkAmrFrTrZone
Object : bts/transceiverZone
Function : Total of the uplink C/I received from the L1m, for AMR full rate calls
Event : This counter is triggered upon reception of uplink C/I from the L1m
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1917/0 Average timing advance values for AMR full rate calls in the cell
Name Q3 : timingAdvanceAmrFrAvg
Object : bts
Function : Average timing advance values for AMR full rate calls in the cell
Event : This counter is triggered upon reception of a STOP
MEASUREMENT ACK message from the BTS. The value given by
the BTS is the average timing advance per communication
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1917/1 Maximum timing advance values for AMR full rate calls in the
cell
Name Q3 : timingAdvanceAmrFrMax
Object : bts
Function : Maximum timing advance values for AMR full rate calls in the cell
Event : This counter is triggered upon reception of a STOP
MEASUREMENT ACK message from the BTS. The value given by
the BTS is the maximum timing advance per communication
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1918/0 Amount of time the downlink power control was running at the
maximum level for the busy half rate AMR TCHs
Name Q3 : downlinkPowerCtrlMaxTchAmrHrCum
downlinkPowerCtrlMaxTchAmrHrEch
downlinkPowerCtrlMaxTchAmrHrMax
downlinkPowerCtrlMaxTchAmrHrMoy
Object : bts
Function : Amount of time the downlink power control was running at the
maximum level for the busy half rate AMR TCHs
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1919/0 Amount of time the uplink power control was running at the
maximum level for the busy half rate AMR TCHs
Name Q3 : uplinkPowerCtrlMaxTchAmrHrCum
uplinkPowerCtrlMaxTchAmrHrEch
uplinkPowerCtrlMaxTchAmrHrMax
uplinkPowerCtrlMaxTchAmrHrMoy
Object : bts
Function : Amount of time the uplink power control was running at the
maximum level for the busy half rate AMR TCHs
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1920/0 Number of downlink RXLEV received from the L1m for AMR
half rate TCH
Name Q3 : RxLevDownlinkAmrHr
RxLevDownlinkAmrHrTrZone
Object : bts/transceiverZone
Function : Number of downlink RXLEV received from the L1m for AMR half
rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1921/0 Number of uplink RXLEV received from the L1m for AMR half
rate TCH
Name Q3 : RxLevUplinkAmrHr
RxLevUplinkAmrHrTrZone
Object : bts/transceiverZone
Function : Number of uplink RXLEV received from the L1m for AMR half rate
TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1922/0 Number of downlink RXQUAL received from the L1m for AMR
half rate TCH
Name Q3 : RxQualDownlinkAmrHr
RxQualDownlinkAmrHrTrZone
Object : bts/transceiverZone
Function : Number of downlink RXQUAL received from the L1m for AMR half
rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1923/0 Number of uplink RXQUAL received from the L1m for AMR
half rate TCH
Name Q3 : RxQualUplinkAmrHr
RxQualUplinkAmrHrTrZone
Object : bts/transceiverZone
Function : Number of uplink RXQUAL received from the L1m for AMR half
rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1924/0 Number of MS increment power control ordered by the L1m for
AMR half rate TCH
Name Q3 : msPowerIncControlAmrHr
Object : bts
Function : Number of MS increment power control ordered by the L1m for AMR
half rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1925/0 Number of MS decrement power control ordered by the L1m for
AMR half rate TCH
Name Q3 : msPowerDecControlAmrHr
Object : bts
Function : Number of MS decrement power control ordered by the L1m for
AMR half rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1926/0 Number of BS increment power control ordered by the L1m for
AMR half rate TCH
Name Q3 : bsPowerIncControlAmrHr
Object : bts
Function : Number of BS increment power control ordered by the L1m for AMR
half rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1927/0 Number of BS decrement power control ordered by the L1m for
AMR half rate TCH
Name Q3 : bsPowerDecControlAmrHr
Object : bts
Function : Number of BS decrement power control ordered by the L1m for AMR
half rate TCH
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1928/0 Total of the uplink C/I received from the L1m, for AMR half rate
calls
Name Q3 : CIUplinkAmrHr
CIUplinkAmrHrTrZone
Object : bts/transceiverZone
Function : Total of the uplink C/I received from the L1m, for AMR half rate calls
Event : This counter is triggered upon reception of uplink C/I from the L1m
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1929/0 Average timing advance values for AMR half rate calls in the cell
Name Q3 : timingAdvanceAmrHrAvg
Object : bts
Function : Average timing advance values for AMR half rate calls in the cell
Event : This counter is triggered upon reception of a STOP
MEASUREMENT ACK message from the BTS. The value given by
the BTS is the average timing advance per communication
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1929/1 Maximum timing advance values for AMR half rate calls in the
cell
Name Q3 : timingAdvanceAmrHrMax
Object : bts
Function : Maximum timing advance values for AMR half rate calls in the cell
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1933/0 Number of capacity intracell handovers filtered
Name Q3 : capacityHoFiltered
Object : bts
Function : Number of capacity intracell handovers filtered
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1934/0 Average and Maximum number of AMR full rate TCH
allocations
Name Q3 : amrFrTchStdAveragedUsedCellMoy
amrFrTchStdAveragedUsedCellMax
amrFrTchStdAveragedUsedCellCum
amrFrTchStdAveragedUsedCellEch
Object : bts
Function : Average and Maximum number of AMR full rate TCH allocations
Event : This counter is incremented when an AMR full rate TCH is allocated
or de--allocated
Type : raw permanent
Source : recorded by the BSC
1937/0 Average and maximum value of the filtered busy TCH ratio
Name Q3 : amrFilteredBusyTchRatioMoy
amrFilteredBusyTchRatioMax
amrFilteredBusyTchRatioCum
amrFilteredBusyTchRatioEch
Object : bts
Function : Average and maximum value of the filtered busy TCH ratio in %
Filtered_TCH_ration = a * (busy_TCH_TS /
available_TCH_TS)+ (1--a) * Filtered_TCH_ration-- 1
Filtered_TCH_ratio0 = 0
Filtered_TCH_ration is the busy TCH ratio managed by the cell at
second n
a is the filter coefficient (filteredTrafficCoefficient parameter)
busy_TCH_TS is the number of TCH TS allocated to a FR or a HR
TCH call (in case of multi--zones cell, traffic of both zones is taken
into account)
available_TCH_TS is the number of TCH TS configurated and
available in the cell (in case of multi--zones cell, traffic of both zones
is taken into account)
Event : Cell load evaluation
Type : raw permanent
Source : recorded by the BSC
Feature : 22688 AMR based on traffic
l
1952/0 Number of outgoing handovers (intra/inter_bss) requests by a
full rate AMR MS
Name Q3 : amrFrHoRequestOutgoingTch
Object : bts
Function : Number of outgoing handovers (intra/inter_bss) requests by a full rate
AMR MS
Event : See function
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1952/1 Number of outgoing handovers (intra/inter_bss) requests by a
half rate AMR MS
Name Q3 : amrHrHoRequestOutgoingTch
Object : bts
Function : Number of outgoing handovers (intra/inter_bss) requests by a half
rate AMR MS
Event : See function
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1953/0 Number of Intracell full rate handover requests for the cell, by an
AMR mobile
Name Q3 : amrFrHoRequestIntraCellTch
Object : bts
Function : Number of Intracell full rate handover requests for the cell, by an
AMR mobile. This counter is incremented at the end of the handover
(success, selection failure, execution, failure or end of call)
Event : This counter is triggered upon an attempt of selection in the cell
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1953/1 Number of Intracell full rate to half rate handover requests for
the cell, by an AMR mobile
Name Q3 : amrFrToHrHoRequestIntraCellTch
Object : bts
Function : Number of Intracell full rate to half rate handover requests for the cell,
by an AMR mobile. This counter is incremented at the end of the
handover (success, selection failure, execution, failure or end of call)
Event : This counter is triggered upon an attempt of selection in the cell
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1953/2 Number of Intracell half rate to full rate handover requests for
the cell, by an AMR mobile
Name Q3 : amrHrToFrHoRequestIntraCellTch
Object : bts
Function : Number of Intracell half rate to full rate handover requests for the cell,
by an AMR mobile. This counter is incremented at the end of the
handover (success, selection failure, execution, failure or end of call)
Event : This counter is triggered upon an attempt of selection in the cell
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1954/0 Number of Intracell full rate handover executions for the cell, by
an AMR mobile
Name Q3 : amrFrHoExecutionIntraCellTch
Object : bts
Function : Number of Intracell full rate handover executions for the cell, by an
AMR mobile. This counter is incremented at the end of the handover
(success, selection failure, execution, failure or end of call)
Event : This counter is triggered upon the transmission of
ASSIGN_COMMAND message
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1954/1 Number of Intracell full rate to half rate handover executions for
the cell, by an AMR mobile
Name Q3 : amrFrToHrHoExecutionIntraCellTch
Object : bts
Function : Number of Intracell full rate to half rate handover executions for the
cell, by an AMR mobile. This counter is incremented at the end of the
handover (success, selection failure, execution, failure or end of call)
Event : This counter is triggered upon the transmission of
ASSIGN_COMMAND message
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1954/2 Number of Intracell half rate to full rate handover executions for
the cell, by an AMR mobile
Name Q3 : amrHrToFrHoExecutionIntraCellTch
Object : bts
Function : Number of Intracell half rate to full rate handover executions for the
cell, by an AMR mobile. This counter is incremented at the end of the
handover (success, selection failure, execution, failure or end of call)
l
1956/0 Number of attempts of half rate AMR handover from a central
cell to a neighboring one
Name Q3 : hoNCellsExecutionTchAmrHr
Object : adjacentCellHandOver
Function : Number of attempts of half rate AMR handover from a central cell to a
neighboring one
Event : This counter is triggered upon reception of the HANDOVER
COMMAND message from the MSC (inter BSC handover), or
transmission of ABIS HANDOVER COMMAND message (intra
BSC handover)
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1957/0 Number of attempts of full rate ARM handover from a central
cell to a neighboring one
Name Q3 : hoNCellsExecutionTchAmrFr
Object : adjacentCellHandOver
Function : Number of attempts of full rate ARM handover from a central cell to a
neighboring one
Event : This counter is triggered upon reception of the HANDOVER
COMMAND message from the MSC (inter BSC handover), or
transmission of ABIS HANDOVER COMMAND message (intra
BSC handover)
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1958/0 Number of unsuccessful half rate AMR handovers from a central
cell to a neighboring one caused by the mobile returning to the old
channel
Name Q3 : hoNCellsUnsuccessTchAmrHrHandoverFailure
Object : adjacentCellHandOver
Function : Number of unsuccessful half rate AMR handovers from a central cell
to a neighboring one caused by the mobile returning to the old channel
Event : This counter is triggered upon reception of the HANDOVER
FAILURE message before T3103 timer expiration
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1958/1 Number of unsuccessful half rate AMR handovers from a central
cell to a neighboring one caused by the expiration of the T3103
timer
Name Q3 : hoNCellsUnsuccessTchAmrHrTimerExpiration
Object : adjacentCellHandOver
Function : Number of unsuccessful half rate AMR handovers from a central cell
to a neighboring one caused by the expiration of the T3103 mobile
Event : This counter is triggered upon the expiration of the T3103 timer. This
is relevant for intra BSS and inter BSS handovers
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1958/2 Number of unsuccessful half rate AMR handovers from a central
cell to a neighboring one caused by other causes
Name Q3 : hoNCellsUnsuccessTchAmrHrClearCommand
Object : adjacentCellHandOver
Function : Number of unsuccessful half rate AMR handovers from a central cell
to a neighboring one caused by other causes (i.e. not caused by those
mentioned in counters 1958/0 or 1958/1)
l
1959/0 Number of unsuccessful full rate AMR handovers from a central
cell to a neighboring one caused by the mobile returning to the old
channel
Name Q3 : hoNCellsUnsuccessTchAmrFrHandoverFailure
Object : adjacentCellHandOver
Function : Number of unsuccessful full rate AMR handovers from a central cell
to a neighboring one caused by the mobile returning to the old channel
Event : This counter is triggered upon reception of the HANDOVER
FAILURE message before T3103 timer expiration
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1959/1 Number of unsuccessful full rate AMR handovers from a central
cell to a neighboring one caused by the expiration of the T3103
timer
Name Q3 : hoNCellsUnsuccessTchAmrFrTimerExpiration
Object : adjacentCellHandOver
Function : Number of unsuccessful full rate AMR handovers from a central cell
to a neighboring one caused by the expiration of the T3103 mobile
Event : This counter is triggered upon the expiration of the T3103 timer. This
is relevant for intra BSS and inter BSS handovers
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1959/2 Number of unsuccessful full rate AMR handovers from a central
cell to a neighboring one caused by other causes
Name Q3 : hoNCellsUnsuccessTchAmrFrClearCommand
Object : adjacentCellHandOver
Function : Number of unsuccessful full rate AMR handovers from a central cell
to a neighboring one caused by other causes (i.e. not caused by those
mentioned in counters 1959/0 or 1959/1)
Event : This counter is triggered upon reception of the CLEAR COMMAND
message with a cause set to another value than “Handover Successful”
or “Call Control”, relevant for inter BSS handovers
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1960/0 Number of releases for full rate AMR mobile caused by Lapdm
Name Q3 : trafficReleaseAmrFrLapdmCause
Object : bts
Function : Number of releases for full rate AMR mobile caused by Lapdm
Event : See Function
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1960/1 Number of releases for full rate AMR mobile caused the radio
Name Q3 : trafficReleaseAmrFrRadioCause
Object : bts
Function : Number of releases for full rate AMR mobile caused by the radio
Event : See Function
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1960/2 Number of releases for full rate AMR mobile caused by other
causes
Name Q3 : trafficReleaseAmrFrOthersCause
Object : bts
Function : Number of releases for full rate AMR mobile caused by other causes
(i.e. not caused by those mentioned in counters 1960/0 or 1960/1)
Event : See Function
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1961/0 Number of releases for half rate AMR mobile caused by Lapdm
Name Q3 : trafficReleaseAmrHrLapdmCause
Object : bts
Function : Number of releases for half rate AMR mobile caused by Lapdm
Event : See Function
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1961/1 Number of releases for half rate AMR mobile caused the radio
Name Q3 : trafficReleaseAmrHrRadioCause
Object : bts
Function : Number of releases for half rate AMR mobile caused by the radio
Event : See Function
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1961/2 Number of releases for half rate AMR mobile caused by other
causes
Name Q3 : trafficReleaseAmrHrOthersCause
Object : bts
Function : Number of releases for half rate AMR mobile caused by other causes
(i.e. not caused by those mentioned in counters 1961/0 or 1961/1)
l
1963/0 Number of half rate AMR handovers requested from a central
cell to a neighboring one
Name Q3 : hoNCellsRequestOutgoingAmrHr
Object : adjacentCellHandOver
Function : Number of half rate AMR handovers requested from a central cell to a
neighboring one
Event : Attempt to select a target cell in the list of eligible cells on
transmission of HANDOVER REQUIRED on the A interface (inter
BSC handover) or attempt to select a target cell in the list of eligible
cells provided by the handover algorithm (intra BSC handover).
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1964/0 Number of full rate AMR handovers requested from a central cell
to a neighboring one
Name Q3 : hoNCellsRequestOutgoingAmrFr
Object : adjacentCellHandOver
Function : Number of full rate AMR handovers requested from a central cell to a
neighboring one
Event : Attempt to select a target cell in the list of eligible cells on
transmission of HANDOVER REQUIRED on the A interface (inter
BSC handover) or attempt to select a target cell in the list of eligible
cells provided by the handover algorithm (intra BSC handover).
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1975/0 Number of 40ms periods during which Codec 4.75 has been
applied on the uplink for full rate AMR
Name Q3 : amrFrUplinkCodec475
amrFrUplinkCodec475TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 4.75 has been applied
on the uplink for full rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1975/1 Number of 40ms periods during which Codec 5.9 has been
applied on the uplink for full rate AMR
Name Q3 : amrFrUplinkCodec59
amrFrUplinkCodec59TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 5.9 has been applied on
the uplink for full rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1975/2 Number of 40ms periods during which Codec 6.7 has been
applied on the uplink for full rate AMR
Name Q3 : amrFrUplinkCodec67
amrFrUplinkCodec67TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 6.7 has been applied on
the uplink for full rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1975/3 Number of 40ms periods during which Codec 10.2 has been
applied on the uplink for full rate AMR
Name Q3 : : amrFrUplinkCodec102
amrFrUplinkCodec102TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 10.2 has been applied
on the uplink for full rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1976/0 Number of 40ms periods during which Codec 4.75 has been
applied on the uplink for half rate AMR
Name Q3 : amrHrUplinkCodec475
amrHrUplinkCodec475TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 4.75 has been applied
on the uplink for half rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1976/1 Number of 40ms periods during which Codec 5.9 has been
applied on the uplink for half rate AMR
Name Q3 : amrHrUplinkCodec59
amrHrUplinkCodec59TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 5.9 has been applied on
the uplink for half rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1976/2 Number of 40ms periods during which Codec 6.7 has been
applied on the uplink for half rate AMR
Name Q3 : amrHrUplinkCodec67
amrHrUplinkCodec67TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 6.7 has been applied on
the uplink for half rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1977/0 Number of 40ms periods during which Codec 4.75 has been
applied on the downlink for full rate AMR
Name Q3 : amrFrDownlinkCodec475
amrFrDownlinkCodec475TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 4.75 has been applied
on the downlink for full rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1977/1 Number of 40ms periods during which Codec 5.9 has been
applied on the downlink for full rate AMR
Name Q3 : amrFrDownlinkCodec59
amrFrDownlinkCodec59TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 5.9 has been applied on
the downlink for full rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1977/2 Number of 40ms periods during which Codec 6.7 has been
applied on the downlink for full rate AMR
Name Q3 : amrFrDownlinkCodec67
amrFrDownlinkCodec67TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 6.7 has been applied on
the downlink for full rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1977/3 Number of 40ms periods during which Codec 10.2 has been
applied on the downlink for full rate AMR
Name Q3 : amrFrDownlinkCodec102
amrFrDownlinkCodec102TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 10.2 has been applied
on the downlink for full rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1978/0 Number of 40ms periods during which Codec 4.75 has been
applied on the downlink for half rate AMR
Name Q3 : amrHrDownlinkCodec475
amrHrDownlinkCodec475TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 4.75 has been applied
on the downlink for half rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1978/1 Number of 40ms periods during which Codec 5.9 has been
applied on the downlink for half rate AMR
Name Q3 : amrHrDownlinkCodec59
amrHrDownlinkCodec59TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 5.9 has been applied on
the downlink for half rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1978/2 Number of 40ms periods during which Codec 6.7 has been
applied on the downlink for half rate AMR
Name Q3 : amrHrDownlinkCodec67
amrHrDownlinkCodec67TrZone
Object : bts/transceiverZone
Function : Number of 40ms periods during which Codec 6.7 has been applied on
the downlink for half rate AMR
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1979/0 Number of bad speech frames (BFI KO) received at the BTS level
for full rate AMR at Codec 4.75
Name Q3 : amrFrBadSpeechFramesCodec475
amrFrBadSpeechFramesCodec475TrZone
Object : bts/transceiverZone
Function : Number of bad speech frames (BFI KO) received at the BTS level for
full rate AMR at Codec 4.75
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1979/1 Number of bad speech frames (BFI KO) received at the BTS level
for full rate AMR at Codec 5.9
Name Q3 : amrFrBadSpeechFramesCodec59
amrFrBadSpeechFramesCodec59TrZone
Object : bts/transceiverZone
Function : Number of bad speech frames (BFI KO) received at the BTS level for
full rate AMR at Codec 5.9
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1979/2 Number of bad speech frames (BFI KO) received at the BTS level
for full rate AMR at Codec 6.7
Name Q3 : amrFrBadSpeechFramesCodec67
amrFrBadSpeechFramesCodec67TrZone
Object : bts/transceiverZone
Function : Number of bad speech frames (BFI KO) received at the BTS level for
full rate AMR at Codec 6.7
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1979/3 Number of bad speech frames (BFI KO) received at the BTS level
for full rate AMR at Codec 10.2
Name Q3 : amrFrBadSpeechFramesCodec102
amrFrBadSpeechFramesCodec102TrZone
Object : bts/transceiverZone
Function : Number of bad speech frames (BFI KO) received at the BTS level for
full rate AMR at Codec 10.2
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1980/0 Received speech frames AMR FR at Codec 4.75
Name Q3 : amrFrValidSpeechFramesCodec475
amrFrValidSpeechFramesCodec475TrZone
Object : bts/transceiverZone
Function : Number of correct and bad speech frames received at the BTS level
for full rate AMR at Codec 4.75
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1980/1 Received speech frames AMR FR at Codec 5.9
Name Q3 : amrFrValidSpeechFramesCodec59
amrFrValidSpeechFramesCodec59TrZone
Object : bts/transceiverZone
Function : Number of correct and bad speech frames received at the BTS level
for full rate AMR at Codec 5.9
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1980/2 Received speech frames AMR FR at Codec 6.7
Name Q3 : amrFrValidSpeechFramesCodec67
amrFrValidSpeechFramesCodec67TrZone
Object : bts/transceiverZone
Function : Number of correct and bad speech frames received at the BTS level
for full rate AMR at Codec 6.7
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1980/3 Received speech frames AMR FR at Codec 10.2
Name Q3 : amrFrValidSpeechFramesCodec102
amrFrValidSpeechFramesCodec102TrZone
Object : bts/transceiverZone
Function : Number of correct and bad speech frames received at the BTS level
for full rate AMR at Codec 10.2
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1981/0 Number of bad speech frames (BFI KO) received at the BTS level
for half rate AMR at Codec 4.75
Name Q3 : amrHrBadSpeechFramesCodec475
amrHrBadSpeechFramesCodec475TrZone
Object : bts/transceiverZone
Function : Number of bad speech frames (BFI KO) received at the BTS level for
half rate AMR at Codec 4.75
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1981/1 Number of bad speech frames (BFI KO) received at the BTS level
for half rate AMR at Codec 5.9
Name Q3 : amrHrBadSpeechFramesCodec59
amrHrBadSpeechFramesCodec59TrZone
Object : bts/transceiverZone
Function : Number of bad speech frames (BFI KO) received at the BTS level for
half rate AMR at Codec 5.9
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1981/2 Number of bad speech frames (BFI KO) received at the BTS level
for half rate AMR at Codec 6.7
Name Q3 : amrHrBadSpeechFramesCodec67
amrHrBadSpeechFramesCodec67TrZone
Object : bts/transceiverZone
Function : Number of bad speech frames (BFI KO) received at the BTS level for
half rate AMR at Codec 6.7
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1982/0 Received speech frames AMR HR at Codec 4.75
Name Q3 : amrHrValidSpeechFramesCodec475
amrHrValidSpeechFramesCodec475TrZone
Object : bts/transceiverZone
Function : Number of correct and bad speech frames received at the BTS level
for half rate AMR at Codec 4.75
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1982/1 Received speech frames AMR HR at Codec 5.9
Name Q3 : amrHrValidSpeechFramesCodec59
amrHrValidSpeechFramesCodec59TrZone
Object : bts/transceiverZone
Function : Number of correct and bad speech frames received at the BTS level
for half rate AMR at Codec 5.9
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1982/2 Received speech frames AMR HR at Codec 6.7
Name Q3 : amrHrValidSpeechFramesCodec67
amrHrValidSpeechFramesCodec67TrZone
Object : bts/transceiverZone
Function : Number of correct and bad speech frames received at the BTS level
for half rate AMR at Codec 6.7
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1983/0 Number of no data frames received or sent on the Abis interface
on the uplink for AMR calls
Name Q3 : amrUplinkNoDataFrames
Object : bts
Function : Number of no data frames received or sent on the Abis interface on the
uplink for AMR calls
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1983/1 Number of no data frames received or sent on the Abis interface
on the downlink for AMR calls
Name Q3 : amrDownlinkNoDataFrames
Object : bts
Function : Number of no data frames received or sent on the Abis interface on the
downlink for AMR calls
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1984/0 Number of Codec increment modifications for full rate AMR in
uplink
Name Q3 : incAmrFrUpModif
incAmrFrUpModifTrZone
Object : bts/transceiverZone
Function : Number of Codec increment modifications for full rate AMR in
uplink
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1984/1 Number of Codec decrement modifications for full rate AMR in
uplink
Name Q3 : decAmrFrUpModif
decAmrFrUpModifTrZone
Object : bts/transceiverZone
Function : Number of Codec decrement modifications for full rate AMR in
uplink
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1985/0 Number of Codec increment modifications for full rate AMR in
downlink
Name Q3 : incAmrFrDownModif
incAmrFrDownModifTrZone
Object : bts/transceiverZone
Function : Number of Codec increment modifications for full rate AMR in
downlink
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1985/1 Number of Codec decrement modifications for full rate AMR in
downlink
Name Q3 : decAmrFrDownModif
decAmrFrDownModifTrZone
Object : bts/transceiverZone
Function : Number of Codec decrement modifications for full rate AMR in
downlink
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1986/0 Number of Codec increment modifications for half rate AMR in
uplink
Name Q3 : incAmrHrUpModif
incAmrHrUpModifTrZone
Object : bts/transceiverZone
Function : Number of Codec increment modifications for half rate AMR in
uplink
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1986/1 Number of Codec decrement modifications for half rate AMR in
uplink
Name Q3 : decAmrHrUpModif
decAmrHrUpModifTrZone
Object : bts/transceiverZone
Function : Number of Codec decrement modifications for half rate AMR in
uplink
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1987/0 Number of Codec increment modifications for half rate AMR in
downlink
Name Q3 : incAmrHrDownModif
incAmrHrDownModifTrZone
Object : bts/transceiverZone
Function : Number of Codec increment modifications for half rate AMR in
downlink
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1987/1 Number of Codec decrement modifications for half rate AMR in
downlink
Name Q3 : decAmrHrDownModif
decAmrHrDownModifTrZone
Object : bts/transceiverZone
Function : Number of Codec decrement modifications for half rate AMR in
downlink
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
l
1988/0 Number of RATSCCH procedure failures for AMR Calls (FR
and HR)
Name Q3 : amrReversalPhaseFailure
Object : bts
Function : number of RATSCCH procedure failures for AMR Calls (FR and
HR). The RATSCCH procedure fails when there is no respose from
the MS after 2 repetitions or negative response received from the MS.
Event : This counter is triggered when data is received by the BSC from the
BTS in STOP MEASUREMENT ACK messages
Type : raw permanent
Source : recorded by the BSC
Note : V14 counter
Name Q3 Location
rachBusyCount CCCH--0
rachBusyCount2 CCCH--2
rachBusyCount4 CCCH--4
rachBusyCount6 CCCH--6
Function : number of RACH bursts received by the BTS that have been decoded;
this internal BTS counter is sent to the BSC in
CCCH_LOAD_INDICATION message.
Event : receipt of a RACH burst decoded by the BTS; receipt of a
CCCH_LOAD_INDICATION message by the BSC.
Type : raw permanent
Class : monitoring
Source : detected by the BTS, recorded by the BSC
Feature : Extended CCCH (TF184 - V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Calls or
Packet Calls.
Note : Counter multiplexed on TSs 0, 2, 4 and 6 for Extended CCCH feature.
l
1027 Number of decoded RACH access forwarded to the BSC
Name Q3 : rachAccessCount
rachAccessCountTs2
rachAccessCountTs4
rachAccessCountTs6
Object : bts
Location :
Name Q3 Location
rachAccessCount CCCH--0
rachAccessCount2 CCCH--2
rachAccessCount4 CCCH--4
rachAccessCount6 CCCH--6
Function : number of RACH bursts that have been decoded and forwarded to the
BSC; this internal BTS counter is sent to the BSC in
CCCH_LOAD_INDICATION message.
Event : transmission of CHANNEL REQUEST to the BSC; receipt of a
CCCH_LOAD_INDICATION message from the BTS
Type : raw permanent
Class : monitoring
Source : detected by the BTS, recorded by the BSC
Feature : Extended CCCH (TF184 - V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Calls or
Packet Calls.
Note : Counter multiplexed on TSs 0, 2, 4 and 6 for Extended CCCH feature.
l
1028 Number of paging messages sent without delay
Name Q3 : pchNoWait
pchNoWaitTs2
pchNoWaitTs4
pchNoWaitTs6
Object : bts
Location :
Name Q3 Location
pchNoWait CCCH--0
pchNoWait2 CCCH--2
pchNoWait4 CCCH--4
pchNoWait6 CCCH--6
Function : number of paging requests which have got a free TS immediately; this
internal BTS counter is sent to the BSC in a
CCCH_LOAD_INDICATION message.
Event : immediate transmission of a PAGING_REQUEST to the MS; receipt
of a CCCH_LOAD_INDICATION message from the BTS.
Type : raw permanent
Class : monitoring
Source : detected by the BTS, recorded by the BSC
Feature : Extended CCCH (TF184 - V12)
Precise
incrementation conditions :
The counter C1028 is related to the Abis paging and also to the paging
that is being sent on radio interface for the first time (the bts paging
repetition is not counted).
The counter C1028 counts the paging messages that have found a free
PCH on the first paging slot occurrence.
That means that C1028 paging messages have waited less than
NoOfMultiframesBetweenPaging multiframes.
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Calls or
Packet Calls.
Data flows : The following data flow presents the Layer 3 messages related to the
paging:
Paging Cmd
PAGING_REQUEST1
+C1028
PAGING_REQUEST2
Est Ind
PAGING_REQUEST3
The BTS repeats NbOfRepeat times all the paging messages coming
from the MSC but the counter C1028 is incremented for the fresh
paging only.
The counter C1028 will be incremented when a free PCH on the first
paging is available.
l
1029 Number of paging messages sent with one slot delay
Name Q3 : pchOneWait
pchOneWaitTs2
pchOneWaitTs4
pchOneWaitTs6
Object : bts
Location :
Name Q3 Location
pchOneWait CCCH--0
pchOneWait2 CCCH--2
pchOneWait4 CCCH--4
pchOneWait6 CCCH--6
Function : number of paging requests which had to wait once before finding a
free TS; this internal BTS counter is sent to the BSC in a
CCCH_LOAD_INDICATION message.
Event : transmission of a PAGING_REQUEST to the MS after one wait;
receipt of a CCCH_LOAD_INDICATION message from the BTS.
Type : raw permanent
Class : monitoring
Source : detected by the BTS, recorded by the BSC
Feature : Extended CCCH (TF184 - V12)
Precise
incrementation conditions :
The counter C1029 is related to the Abis paging and also to the paging
that is being sent on radio interface for the first time (the bts paging
repetition is not counted).
The counter C1029 counts the paging messages that have found a free
PCH on the second paging slot occurrence. It means that C1029
paging messages have waited more than
NbOfMultiframesBetweenPaging multiframes and less than 2x
NbOfMultiframesBetweenPaging multiframes.
For example:
If NbOfMultiframesBetweenPaging = 8 (8 multiframes of 240ms
between the same paging group), C1029 paging messages have
waited between 1x8x240 ms (about 2 sec) and 2x8x240 ms (about 4
sec).
Paging Cmd
(1 ST PAGING SLOT OCCUR-
RENCE IS BUSY)
PAGING_REQUEST1
+C1029
PAGING_REQUEST2
Est Ind
PAGING_REQUEST3
The BTS repeats NbOfRepeat times all the paging messages coming
from the MSC but the counter C1029 is incremented for the fresh
paging only.
The fresh paging message has to wait for the next paging group slot as
the first paging group presented was busy.
l
1030 Number of paging messages sent with two slots delay
Name Q3 : pchTwoWait
pchTwoWaitTs2
pchTwoWaitTs4
pchTwoWaitTs6
Object : bts
Location :
Name Q3 Location
pchTwoWait CCCH--0
pchTwoWait2 CCCH--2
pchTwoWait4 CCCH--4
pchTwoWait6 CCCH--6
Function : number of paging requests which had to wait twice before finding a
free TS; this internal BTS counter is sent to the BSC in a
CCCH_LOAD_INDICATION message.
Event : transmission of a PAGING_REQUEST to the MS after two waits;
receipt of a CCCH_LOAD_INDICATION message from the BTS.
Type : raw permanent
Class : monitoring
Source : detected by the BTS, recorded by the BSC
Feature : Extended CCCH (TF184 - V12)
Precise
incrementation conditions :
The counter C1030 is related to the Abis paging and also to the paging
that is being sent on radio interface for the first time (the bts paging
repetition is not counted).
The counter C1030 counts the paging messages that have found a free
PCH on the third paging group occurrence because the 2 previous
ones were busy. It means that the counter C1030 fresh paging
messages from the MSC have waited more than
2xNbOfMultiframesBetweenPaging multiframes and less than
3xNbOfMultiframesBetweenPaging multiframe to get its free PCH.
PAGING_REQUEST1
+C1030
PAGING_REQUEST2
Est Ind
PAGING_REQUEST3
The BTS repeats NbOfRepeat times all the paging messages coming
from the MSC but the counter C1030 is incremented for the fresh
paging only.
The fresh paging message has to wait for the next paging group slot as
the first and second paging groups presented were busy.
l
1031 Number of paging messages sent with more than two slots delay
Name Q3 : pchMoreWait
pchMoreWaitTs2
pchMoreWaitTs4
pchMoreWaitTs6
Object : bts
Location :
Name Q3 Location
pchMoreWait CCCH--0
pchMoreWait2 CCCH--2
pchMoreWait4 CCCH--4
pchMoreWait6 CCCH--6
Function : number of paging requests which had to wait twice before finding a
free TS; this internal BTS counter is sent to the BSC in a
CCCH_LOAD_INDICATION message.
Event : transmission of a PAGING_REQUEST to the MS; receipt of a
CCCH_LOAD_INDICATION message from the BTS.
Type : raw permanent
Class : monitoring
Source : detected by the BTS, recorded by the BSC
Feature : Extended CCCH (TF184 - V12)
Precise
incrementation conditions :
The counter C1031 is related to the Abis paging and also to the paging
that is being sent on radio interface for the first time (the bts paging
repetition is not counted).
The counter C1031 counts the paging messages that need to wait
more than 2 paging group slots. It means that the counter C1031 fresh
paging messages from the MSC have waited for more than
3xNbOfMultiframesBetweenPaging multiframes.
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Calls or
Packet Calls.
Data flows : The following dataflow presents the Layer 3 messages related to the
paging:
Paging Cmd
(1 ST, 2 ND, AND 3 RD PAGING SLOT
OCCURRENCES ARE BUSY)
PAGING_REQUEST1
+C1031
PAGING_REQUEST2
Est Ind
PAGING_REQUEST3
The BTS repeats NbOfRepeat times all the paging messages coming
from the MSC but the counter C1031 is incremented for the fresh
paging only.
The fresh paging message has to wait for the next paging group slot as
the first, second, and third paging groups presented were busy.
l
1033 Average level of non-decoded RACH access
Name Q3 : rachNonDecodedAvLevelMoy
rachNonDecodedAvLevelTs2Moy
rachNonDecodedAvLevelTs4Moy
rachNonDecodedAvLevelTs6Moy
rachNonDecodedAvLevelMax = Max RACH access level
rachNonDecodedAvLevelTs2Max = Max RACH access level
rachNonDecodedAvLevelTs4Max = Max RACH access level
rachNonDecodedAvLevelTs6Max = Max RACH access level
rachNonDecodedAvLevelCum = Total RACH access level
rachNonDecodedAvLevelTs2Cum = Total RACH access level
rachNonDecodedAvLevelTs4Cum = Total RACH access level
rachNonDecodedAvLevelTs6Cum = Total RACH access level
rachNonDecodedAvLevelEch = Number of samples
rachNonDecodedAvLevelTs2Ech = Number of samples
rachNonDecodedAvLevelTs4Ech = Number of samples
rachNonDecodedAvLevelTs6Ech = Number of samples
Object : bts
Location :
Name Q3 Location
rachNonDecodedAvLevelMoy/Max/Cum/Ech CCCH--0
rachNonDecodedAvLevelTs2Moy/Max/Cum/Ech CCCH--2
rachNonDecodedAvLevelTs4Moy/Max/Cum/Ech CCCH--4
rachNonDecodedAvLevelTs6Moy/Max/Cum/Ech CCCH--6
l
1045 Average time of a signaling channel seizure > 25 s
Name Q3 : signallingPhaseDurationHighMoy . Average time of seizure > 25 s
signallingPhaseDurationHighMax . Max time of seizure > 25 s
signallingPhaseDurationHighCum Total time of seizure > 25 s
signallingPhaseDurationHighEch . Number of samples
Object : bts
Function : average (= total seizure divided by number of samples) and maximum
seizure of signaling channels expressed in milliseconds, calculated on
all allocations lasting more than 25 seconds
Event : signaling channel allocation on reception of CONNECTION
CONFIRM (first establishment in the BSS) or HANDOVER
COMPLETE (incoming inter handover in signaling phase) /
deallocation on reception of ASSIGN COMPLETE or when the call is
released
allocation: start timer
deallocation: stop and read timer. When the value read is greater
than 25 seconds, do the following:
• store its peak value
• add measured value to the total number of allocations lasting
more than 25 seconds for the observation period
• step up by one the number of samples
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1050 Number of TCH/FR or a preempted PDTCH successfully
assigned
Name Q3 : successfulTchFrSeizures
Object : bts
Function : number of TCH/FR or a preempted PDTCH assignments in the
observation period
Event : receipt of ASSIGNMENT COMPLETE message by the BSC
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “Direct retry handover procedure”
l
1055 Number of ASSIGN FAILURE messages received on TCH
Name Q3 : assignFailure
Object : bts
Function : number of ASSIGNMENT FAILURE messages sent by the cell
Event : receipt of an ASSIGNMENT FAILURE messages sent on TCH or
preempted PDTCH from the MS
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1057 Average duration to allocate all TCH/FR and preempted PDTCH
resources
Name Q3 : allTchFrAllocatedTimeMoy . . . . . . Average allocation duration
allTchFrAllocatedTimeMax . . . . . . Maximum allocation duration
allTchFrAllocatedTimeCum . . . . . Total allocation duration
allTchFrAllocatedTimeEch . . . . . . Number of samples
allTchFrAllocatedTimeTrZoneMoy Average allocation duration
allTchFrAllocatedTimeTrZoneMax Maximum allocation duration
allTchFrAllocatedTimeTrZoneCum Total allocation duration
allTchFrAllocatedTimeTrZoneEch Number of samples
Object : bts/transceiverZone
Class : allocation
Source : calculated by the OMC--R agent
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
When new counter 1823 is received, its value is copied in counter
1057.
Note : A blocked resource is neither considered as used nor available.
l
1060/0 Average allocation duration of all SDCCH resources
Name Q3 : allSdcchAllocatedTimeMoy . . . . . Average allocation duration
allSdcchAllocatedTimeMax . . . . . . Maximum allocation duration
allSdcchAllocatedTimeCum . . . . . Total allocation duration
allSdcchAllocatedTimeEch . . . . . . Number of samples
allSdcchAllocatedTimeTrZoneMoy Average allocation duration
allSdcchAllocatedTimeTrZoneMax Maximum allocation duration
allSdcchAllocatedTimeTrZoneCum Total allocation duration
allSdcchAllocatedTimeTrZoneEch Number of samples
Object : bts/transceiverZone
Function : average (= total duration divided by number of samples) and
maximum allocation duration of all available SDCCHs used in the
cell for the observation period, expressed in milliseconds
Event : Start and stop events are the following:
starts when the last available SDCCH resource in the cell is
allocated
stops as soon as a SDCCH resource is freed
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1065/0 Number of outgoing intra--bss handovers on TCH executed
Name Q3 : hoExecutionOutgoingIntraBss
Object : bts
Function : number of attempts to execute outgoing intra-bss handovers on TCH
Event : transmission of HANDOVER COMMAND to the serving cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
l
1068/0 Number of successful outgoing inter--bss handovers on TCH
except those after first attempt
Name Q3 : hoSuccessOutgoingInterBss
Object : bts
Function : number of successful outgoing inter-bss handovers on TCH except
those after first attempt
Event : receipt of CLEAR COMMAND from the MSC with cause “Handover
Successful”
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Note : For the number of successful outgoing inter handovers on TCH after
first attempt see counter 1078.
l
1069 Number of incoming intra--bss handovers on TCH requested
Name Q3 : hoRequestIncomingIntraBss
Object : bts
Function : number of incoming intra-bss handover requests on TCH in the cell
for any kind of the mobile
Event : attempt to select a target cell in the list of eligible cells on transmission
of HANDOVER REQUIRED on the A interface
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Note : the counter is incremented at the end of the handover (success,
selection failure, execution failure or end of call)
l
1070 Number of incoming inter--bss handovers on TCH requested
Name Q3 : hoRequestIncomingInterBss
Object : bts
Function : number of incoming inter-bss handover requests on TCH in the cell
Event : receipt of HANDOVER REQUEST from the MSC on the A interface
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1071 Number of incoming intra--bss handovers on TCH execution
attempts
Name Q3 : hoExecutionIncomingIntraBss
Object : bts
Function : number of attempts to execute incoming intra-bss handovers on TCH
in the cell for any kind of the mobile
Event : transmission of HANDOVER COMMAND to the serving cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Note : the counter is incremented at the end of the handover (success,
selection failure execution failure or end of call)
l
1072 Number of incoming inter--bss handovers on TCH executed
Name Q3 : hoExecutionIncomingInterBss
Object : bts
Function : number of attempts to execute incoming inter-bss handovers on TCH
Event : transmission of HANDOVER REQUEST ACKNOWLEDGE from
the target BSS to the MSC
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1073 Number of successful incoming intra--bss handovers on TCH
Name Q3 : hoSuccessIncomingIntraBss
Object : bts
Function : number of successful incoming intra-bss handovers on TCH in the
cell
Event : receipt of HANDOVER COMPLETE from the target cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1074 Number of successful incoming inter--bss handovers on TCH
Name Q3 : hoSuccessIncomingInterBss
Object : bts
Function : number of successful incoming inter-bss handovers on TCH
l
1076 Number of outgoing inter--bss handovers on TCH requested
Name Q3 : hoRequestOutgoingInterBss
Object : bts
Function : number of outgoing inter-bss handover requests on TCH in the cell
Event : attempt to select a target cell in the list of eligible cells on transmission
of HANDOVER REQUIRED on the A interface
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1077 Number of successful outgoing intra--bss handovers on TCH
after first attempt
Name Q3 : hoSuccessOutgoingFirstIntra
Object : bts
Function : number of successful outgoing intra-bss handovers on TCH to the first
cell from the list of eligible cells
Event : receipt of HANDOVER COMPLETE from the target cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1078 Number of successful outgoing inter--bss handovers on TCH after
first attempt
Name Q3 : hoSuccessOutgoingFirstInter
Object : bts
Function : number of successful outgoing inter-bss handovers on TCH to the first
cell from the list of eligible cells
Event : receipt of CLEAR COMMAND from the MSC with cause “Handover
Successful”
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Note : the list is reorganized by the BSC Ho decision according to the cell
priority feature (TF716). It may not be the same order as the one
received from the L1M.
l
1081 Number of intra-bts handovers on TCH requested
Name Q3 : hoRequestIntraBts
Object : bts
Function : number of intra-bts handovers on TCH requested in the cell
Event : transmission of HANDOVER INDICATION
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1082 Number of intra-bts handovers on TCH executed
Name Q3 : hoExecutionIntraBts
Object : bts
Function : number of attempts to execute intra-bts handovers on TCH in the cell
Event : transmission of ASSIGN COMMAND to the cell during the intra-bts
handover procedure
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1083 Number of successful intra-bts handovers on TCH
Name Q3 : hoSuccessIntraBts
Object : bts
Function : number of successful intra-bts handovers on TCH in the cell
Event : receipt of ASSIGN COMPLETE from the cell during the intra-bts
handover procedure
Type : raw permanent
Class : handover
Source : recorded by the BSC
Note : This counter is the sum of the 1073 and 1077 counters.
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1094 Number of terrestrial circuits allocated
Name Q3 : tcAllocated
Object : bsc
Function : number of terrestrial circuit allocations (CIC) in the BSC
Event : allocation of a terrestrial circuit
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (no resource available for a PDTCH
preemption)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “Dedicated channel assignment modify procedure (normal
completion)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
DFD “Radio channel release RELEASE INDICATION procedure
(normal completion)”
DFD “Connection clearing required by the BSC procedure
(communication on TRAFFIC phase)”
l
1104/0 Number of SCCP connections established for SSN BSSMAP
Name Q3 : sccpAllocated
Object : bsc
Function : number of SCCP connections for SSN BSSMAP in the BSC
Event : successful SCCP connection request
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
This counter is concerned by the following calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Dedicated channel assignment modify procedure (normal
completion)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Connection clearing required by the BSC procedure
(communication on SIGNALING phase)”
DFD “SMS procedure (SMS established by the MS)”
l
1104/1 Number of SCCP connections established for SSN LCS
Name Q3 : sccpAllocatedLcs
Object : bsc
Function : number of SCCP connections for SSN LCS in the BSC
Event : successful SCCP connection request
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
This counter is concerned by the location procedure beginning, for
BSS hybrid solution.
l
1105 Average number of SCCP connections established
Name Q3 : sccpAveragedUsedMoy . . Average SCCP connections established
sccpAveragedUsedMax . . Max SCCP connections established
sccpAveragedUsedCum . . Total SCCP connections established
sccpAveragedUsedEch . . . Number of samples
Object : bsc
Function : average (= total number divided by number of samples) and
maximum number of SCCP connections established in the BSC,
obtained through internal sampling.
Event : SCCP connection establishment/release, internal sampling time-out
elapse:
establishment: step up by one the instantaneous value of SCCP
connections established
release: step down by one the instantaneous value of SCCP
connections established
sampling time-out elapse:
• read the instantaneous value of SCCP connections established
• store its peak value
• add it to the total number of SCCP connections established for
the observation period
• step up by one the number of samples
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1106/1 Number of SCCP connections refused by the BSC
Name Q3 : sccpRessourceFailureBscRefusal
Object : bsc
Function : number of SCCP connection establishments refused
Event : SCCP connection establishment refusal due to the following causes:
MSC request refused by the BSC
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1106/2 Number of SCCP connections with SSN LCS, refused by the
MSC or the local SCCP layer
Name Q3 : sccpRessourceFailureLcs
Object : bsc
Function : number of SCCP connections with SSN LCS, refused by the MSC or
the local SCCP layer
Event : SCCP connection establishment (with SSN LCS) refusal due to the
following causes:
BSC request refused by local SCCP layer
BSC request refused by the MSC
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
This counter is concerned by the location procedure beginning, for
BSS hybrid solution.
l
1106/3 Number of SCCP connections with SSN LCS, refused by the BSC
Name Q3 : sccpRessourceFailureBscRefusalLcs
Object : bsc
Function : number of SCCP connections with SSN LCS refused by the BSC
Event : SCCP connection establishment (with SSN LCS) refusal due to the
following causes:
MSC request refused by the BSC
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
This counter is concerned by the location procedure beginning, for
BSS hybrid solution.
l
1107 Number of BSSAP messages received
Name Q3 : aInputMessage
Object : bsc
Function : number of BSSAP messages received by the BSC
Event : receipt of SCCP CONNECTION REQUEST, or SCCP DATA
REQUEST, or SCCP UNIT DATA REQUEST message
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion)”
DFD “GPRS procedure (no available resource for a PDTCH
preemption)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “Immediate assignment procedure (normal completion)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “dedicated channel assignment procedure (no Resource
available and queuing not activated)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
DFD “Connection clearing required by the BSC procedure
(communication on TRAFFIC phase)”
DFD “Connection clearing required by the BSC procedure
(communication on SIGNALING phase)”
DFD “SMS procedure (SMS established by the MS)”
l
1109 Number of erroneous BSSAP messages received
Name Q3 : aMessageErrors
Object : bsc
Function : number of errored BSSAP messages received by the BSC at
application level
Event : receipt of SCCP CONNECTION INDICATION, or SCCP DATA
INDICATION, or SCCP UNIT DATA INDICATION, with incorrect
format
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1134 Number of unsuccessful intra-bts handovers on TCH for which
the communication has been re--established on starting channel
Name Q3 : hoUnsuccessReestIntraBtsTch
Object : bts
Function : number of unsuccessful intra-bts handovers on TCH for which the
communication has been re--established on starting channel
Event : receipt of ASSIGN FAILURE before T3107 time-out elapse
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1135 Number of unsuccessful outgoing intra--bss handovers on TCH
for which the communication has been re--established on starting
channel
Name Q3 : hoUnsuccessReestOutgoingIntraBssTch
Object : bts
Function : number of unsuccessful outgoing intra-bss handovers for which the
communication has been re--established on starting channel
Event : receipt of HANDOVER FAILURE before T3103 time-out elapse
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1136 Number of unsuccessful outgoing inter--bss handovers on TCH
for which the communication has been re--established on starting
channel
Name Q3 : hoUnsuccessReestOutgoingInterBssTch
Object : bts
Function : number of unsuccessful outgoing inter-bss handovers on TCH for
which the communication has been re--established on starting channel
l
1138/9 Number of intra-bts handovers on TCH required: Loss of
Downlink quality
Name Q3 : hoRequiredTchIntraBtsDownlink
Object : bts
Function : number of intra-bts handovers on TCH required because of loss of
Downlink quality (BTS-to-MS direction)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“downlink signal quality” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1138/10 Number of directed retry handovers on TCH required
Name Q3 : hoRequiredTchDirectedRetry
Object : bts
Function : number of directed retry handovers on TCH required
Event : receipt of HANDOVER INDICATION (internal message) attempt of
directed retry: receipt of CONNECTION REQUEST ACK message
or autonomously in case of directed retry from a micro--cell receipt of
a CONNECTION REQUEST ACK with an eligible cells list, after
Tchoke expiry
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1138/11 intra--cell handover into a class 0 TDMA for downlink power
level or distance, for a multi--class cell (concentric cell...) (only for
HO_REQUIRED_TCH)
Name Q3 : hoRequiredTchTdmaClass0
Object : bts (concentric cell)
Function : TDMA_class_0: intra--cell handover into a class 0 TDMA for
downlink power level or distance, for a multi--class cell (concentric
cell...) (only for HO_REQUIRED_TCH)
Event : receipt of HANDOVER INDICATION (internal message) with cause
downlink power level or distance reason from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1138/15 Number of handovers on TCH required: Tiering handover from
large pattern to small pattern
Name Q3 : hoRequiredTchTieringLargeToSmallPattern
Object : bts
Function : number of tiering handovers on TCH from large pattern to small
pattern (non--hopping channel to hopping channel)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“tiering handover from large pattern to small pattern” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Feature : Cell Tiering (TF995 - V12)
l
1138/16 Number of handovers on TCH required: Tiering handover from
small pattern to large pattern
Name Q3 : hoRequiredTchTieringSmallToLargePattern
Object : bts
Function : number of tiering handovers on TCH from small pattern to large
pattern (hopping channel to non--hopping channel)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“tiering handover from large small to large pattern” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Feature : Cell Tiering (TF995 - V12)
l
1139/0 Number of handovers on SDCCH required: Loss of Uplink power
Name Q3 : hoRequiredSdcchUplinkStrength
Object : bts
Function : number of handovers on SDCCH required because of loss of Uplink
power (MS-to-BTS direction)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“uplink signal strength” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/1 Number of handovers on SDCCH required: Loss of Downlink
power
Name Q3 : hoRequiredSdcchDownlinkStrength
Object : bts
Function : number of handovers on SDCCH required because of loss of
Downlink power (BTS-to-MS direction)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“downlink signal strength” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/2 Number of handovers on SDCCH required: Loss of Uplink
quality
Name Q3 : hoRequiredSdcchUplinkQuality
Object : bts
Function : number of handovers on SDCCH required because of loss of Uplink
quality (MS-to-BTS direction)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“uplink signal quality” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/3 Number of handovers on SDCCH required: Loss of Downlink
quality
Name Q3 : hoRequiredSdcchDownlinkQuality
Object : bts
Function : number of handovers on SDCCH required because of loss of
Downlink quality (BTS-to-MS direction)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“downlink signal quality” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/4 Number of handovers on SDCCH required: Distance
Name Q3 : hoRequiredSdcchDistance
Object : bts
Function : number of handovers on SDCCH required because of distance
Event : receipt of HANDOVER INDICATION (internal message) with cause
“distance” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/5 Number of handovers on SDCCH required: Power budget
Name Q3 : hoRequiredSdcchPowerBudget
Object : bts
Function : number of handovers on SDCCH required because of power budget
Event : receipt of HANDOVER INDICATION (internal message) with cause
“power budget” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/6 Number of handovers on SDCCH required: Microcell capture
Name Q3 : hoRequiredSdcchCapture
Object : bts
Function : number of handovers on SDCCH required because of microcell
capture
Event : receipt of HANDOVER INDICATION (internal message) with cause
“microcell capture” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/7 Number of intra-bts handovers on SDCCH required: TRX out of
service O&M
Name Q3 : hoRequiredSdcchIntraBtsOm
Object : bts
Function : number of intra-bts handovers on SDCCH required because of a
TRX/DRX taken out of service (O&M action)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“TRX out of service” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/8 Number of intra-bts handovers on SDCCH required: Loss of
Uplink quality
Name Q3 : hoRequiredSdcchIntraBtsUplink
Object : bts
Function : number of intra-bts handovers on SDCCH required because of loss of
Uplink quality (MS-to-BTS direction)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“uplink signal quality” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/9 Number of intra-bts handovers on SDCCH required: Loss of
Downlink quality
Name Q3 : hoRequiredSdcchIntraBtsDownlink
Object : bts
Function : number of intra-bts handovers on SDCCH required because of loss of
Downlink quality (BTS-to-MS direction)
Event : receipt of HANDOVER INDICATION (internal message) with cause
“downlink signal quality” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/13 Number of handovers on SDCCH required: Forced handover
O&M
Name Q3 : hoRequiredSdcchInterBtsOm
Object : bts
Function : number of handovers on SDCCH forced towards the neighbor cells of
the serving cell
Event : receipt of HANDOVER INDICATION (internal message) with cause
“forced handover” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1139/14 Number of handovers on SDCCH required: Traffic
Name Q3 : hoRequiredSdcchTraffic
Object : bts
Function : number of handovers on SDCCH forced towards the neighbor cells of
the serving cell
Event : receipt of HANDOVER INDICATION (internal message) with cause
“traffic” from the L1M
Type : raw permanent
Class : handover
Source : recorded by the BSC
Feature : Handover for traffic reasons (TF132 - V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1140 Number of outgoing intra--bss handovers on SDCCH executed
Name Q3 : hoExecutionOutgoingIntraBssSdcch
Object : bts
Function : number of attempts to execute outgoing intra-bss handovers on
SDCCH
Event : transmission of HANDOVER COMMAND to the serving cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1141 Number of outgoing inter handovers on SDCCH executed
Name Q3 : hoExecutionOutgoingInterBssSdcch
Object : bts
Function : number of attempts to execute outgoing inter-bss handovers on
SDCCH
Event : receipt of HANDOVER COMMAND from the MSC
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1142 Number of successful outgoing intra--bss handovers on SDCCH
Name Q3 : hoSuccessOutgoingIntraBssSdcch
Object : bts
Function : number of successful attempts to execute outgoing intra-bss
handovers on SDCCH
Event : receipt of HANDOVER COMPLETE from the target cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1143 Number of successful outgoing inter--bss handovers on SDCCH
Name Q3 : hoSuccessOutgoingInterBssSdcch
Object : bts
Function : number of successful outgoing inter-bss handovers on SDCCH
Event : receipt of CLEAR COMMAND with cause “ Handover Successful ”
from the MSC
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1144 Number of incoming intra--bss handovers on SDCCH requested
Name Q3 : hoRequestIncomingIntraBssSdcch
Object : bts
Function : number of incoming intra-bss handovers on SDCCH requested in the
cell for any kind of the mobile
Event : attempt to select the cell as the serving cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : the counter is incremented at the end of the handover (success,
selection failure, execution failure or end of call)
l
1145 Number of incoming inter--bss handovers on SDCCH requested
Name Q3 : hoRequestIncomingInterBssSdcch
Object : bts
Function : number of incoming inter-bss handovers on SDCCH requested
Event : receipt of HANDOVER REQUEST from the MSC on the A interface
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1146 Number of incoming intra--bss handovers on SDCCH execution
attempt
Name Q3 : hoExecutionIncomingIntraBssSdcch
Object : bts
Function : number of attempts to execute incoming intra-bss handovers on
SDCCH in the cell for any kind of the mobile
Event : transmission of HANDOVER COMMAND to the serving cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : the counter is incremented at the end of the handover (success,
selection failure, execution failure or end of call)
l
1147 Number of incoming inter--bss handovers on SDCCH executed
Name Q3 : hoExecutionIncomingInterBssSdcch
Object : bts
Function : number of attempts to execute incoming inter-bss handovers on
SDCCH
Event : transmission of HANDOVER REQUEST ACKNOWLEDGE from
the target BSS to the MSC
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1148 Number of successful incoming intra--bss handovers on SDCCH
Name Q3 : hoSuccessIncomingIntraBssSdcch
Object : bts
Function : number of successful incoming intra-bss handovers on SDCCH in the
cell
Event : receipt of HANDOVER COMPLETE from the target cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1149 Number of successful incoming inter--bss handovers on SDCCH
Name Q3 : hoSuccessIncomingInterBssSdcch
Object : bts
Function : number of successful incoming inter-bss handovers on SDCCH
Event : receipt of HANDOVER COMPLETE from the target cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1150 Number of outgoing intra--bss handovers on SDCCH requested
Name Q3 : hoRequestOutgoingIntraBssSdcch
Object : bts
Function : number of outgoing intra-bss handovers on SDCCH requested
Event : attempt to select a target cell from the list of eligible cells sent by the
handover algorithm
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1151 Number of outgoing inter--bss handovers on SDCCH requested
Name Q3 : hoRequestOutgoingInterBssSdcch
Object : bts
Function : number of outgoing inter-bss handovers on SDCCH requested
Event : attempt to select a cell in the list of eligible cells on transmission of
HANDOVER REQUIRED on the A interface
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1152 Number of successful outgoing intra--bss handovers on SDCCH
after first attempt
Name Q3 : hoSuccessOutgoingFirstIntraSdcch
Object : bts
Function : number of successful outgoing intra-bss handovers on SDCCH to the
first cell from the list of eligible cells
Event : receipt of HANDOVER COMPLETE from the target cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : the list is reorganized by the BSC Ho decision according tot he cell
priority feature (TF716). It may not be the same order as the one
received from the L1M
l
1153 Number of successful outgoing inter--bss handovers on SDCCH
after first attempt
Name Q3 : hoSuccessOutgoingFirstInterSdcch
Object : bts
Function : number of successful outgoing inter-bss handovers on SDCCH to the
first cell from the list of eligible cells
Event : receipt of CLEAR COMMAND with cause “Handover Successful”
from the MSC
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : the list is reorganized by the BSC Ho decision according tot he cell
priority feature (TF716). It may not be the same order as the one
received from the L1M
l
1154 Number of intra-bts handovers on SDCCH requested
Name Q3 : hoRequestIntraBtsSdcch
Object : bts
Function : number of intra-bts handovers on SDCCH requested in the cell
Event : receipt of ASSIGN COMPLETE from the cell during the intra-bts
handover procedure
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1157 Number of unsuccessful intra-bts handovers on SDCCH for
which the communication has been re--established on starting
channel
Name Q3 : hoUnsuccessReestIntraBtsSdcch
Object : bts
Function : number of unsuccessful intra-bts handovers on SDCCH for which the
communication has been re--established on starting channel
Event : receipt of ASSIGN FAILURE before T3107 time-out elapse
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1158 Number of unsuccessful outgoing intra--bss handovers on
SDCCH for which the communication has been re--established
on starting channel
Name Q3 : hoUnsuccessReestOutgoingIntraBssSdcch
Object : bts
Function : number of unsuccessful outgoing intra-bss handovers on SDCCH for
which the communication has been re--established on starting channel
Event : receipt of HANDOVER FAILURE before T3103 time-out elapse
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1159 Number of unsuccessful outgoing inter--bss handovers on
SDCCH for which the communication has been re--established
on starting channel
Name Q3 : hoUnsuccessReestOutgoingInterBssSdcch
Object : bts
Function : number of unsuccessful outgoing inter-bss handovers on SDCCH for
which the communication has been re--established on starting channel
Event : receipt of HANDOVER FAILURE before T3103 time-out elapse
(T3103 < bssMapT8) with transmission to the MSC
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1160 Number of unsuccessful incoming intra--bss handovers on
SDCCH for which the communication has been re--established
on starting channel
Name Q3 : hoUnsuccessReestIncomingIntraBssSdcch
Object : bts
Function : number of unsuccessful incoming intra-bss handovers on SDCCH for
which the communication has been re--established on starting channel
Event : receipt of HANDOVER FAILURE
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1161/0 Number of immediate assignments rejected: Traffic with MSC
interrupted
Name Q3 : immediateAssignmentRejectTraffMsc
Object : bts
Function : number of immediate assignments rejected because the traffic with
the MSC is interrupted
Event : transmission of IMMEDIATE ASSIGN REJECT to a mobile on
transmission or receipt of RESET by the MSC
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1161/1 Number of immediate assignments rejected: Lack of radio
resource
Name Q3 : immediateAssignmentRejectRadioRes
Object : bts
Function : number of immediate assignments rejected for lack of radio resources
Event : transmission of IMMEDIATE ASSIGN REJECT to a mobile due to a
lack of radio resource
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1161/2 Number of immediate assignments rejected: CHANNEL
ACTIVATE NACK received
Name Q3 : immediateAssignmentRejectChanActNack
Object : bts
Function : number of immediate assignments rejected because a CHANNEL
ACTIVATE NACK message is received
Event : transmission of IMMEDIATE ASSIGN REJECT to a mobile on
receipt of CHANNEL ACTIVATE NACK from the BTS
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1161/3 Number of immediate assignments rejected: Time-out elapse
Name Q3 : immediateAssignmentRejectChanActTimmack
Object : bts
Function : number of immediate assignments rejected because of TimmAck
time-out elapse
Event : transmission of IMMEDIATE ASSIGN REJECT to a mobile on
TchnAck time-out elapse
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1161/5 Number of immediate assignments rejected: Traffic overload
Name Q3 : immediateAssignmentRejectOverload
Object : bts
Function : number of immediate assignments rejected for overload reasons
Event : transmission of IMMEDIATE ASSIGN REJECT to a mobile because
a call originating from a mobile (MOC) or a Mobile Terminating Call
(MTC) is blocked by the BSC for traffic management general
overload
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1161/6 Number of immediate assignments rejected: Excessive timing
advance
Name Q3 : immediateAssignmentRejectTimingAdv
Object : bts
Function : number of immediate assignments rejected for distance reasons
Event : receipt of CHANNEL REQUIRED with a timing advance value
above the O&M threshold (no IMMEDIATE ASSIGN REJECT is
sent to the mobile)
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1161/7 Number of immediate assignments rejected: Other cases
Name Q3 : immediateAssignmentRejectOthers
Object : bts
Function : number of immediate assignments rejected for other reasons
Event : transmission of IMMEDIATE ASSIGN REJECT to a mobile for
another reason
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1162/0 Number of SCCP releases before HANDOVER REQUEST
acknowledging: SCCP disconnection
Name Q3 : signallingReleaseNoBtsSccpDiscInd
Object : bsc
Function : number of communications in signaling phase released before
HANDOVER REQUEST ACKNOWLEDGE is received in the
incoming handover procedure, because of SCCP disconnection
Event : receipt of SCCP DISCONNECTION INDICATION from the MSC
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : This counter is only incremented in case of incoming external
handovers.
l
1162/1 Number of SCCP releases before HANDOVER REQUEST
acknowledging: Reset
Name Q3 : signallingReleaseNoBtsReset
Object : bsc
Function : number of communications in signaling phase released before
HANDOVER REQUEST ACKNOWLEDGE is received in the
incoming handover procedure, because of reset
l
1162/3 Number of SCCP releases before HANDOVER REQUEST
acknowledging: SCCP DATA REFUSAL received
Name Q3 : signallingReleaseNoBtsSccpDataRefusal
Object : bsc
Function : number of communications in signaling phase released before
HANDOVER REQUEST ACKNOWLEDGE is received in the
incoming handover procedure, because of SCCP data refusal
Event : receipt of SCCP DATA REFUSAL from the MSC
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : This counter is only incremented in case of incoming external
handovers.
l
1162/26 Number of SCCP releases before HANDOVER REQUEST
acknowledging: TsccRel elapse
Name Q3 : signallingReleaseNoBtsTsccRel
Object : bsc
Function : number of communications in signaling phase released before
HANDOVER REQUEST ACKNOWLEDGE is received in the
incoming handover procedure, because of TsccRel time-out elapse
Event : TsccRel time-out elapse
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : This counter is only incremented in case of incoming external
handovers.
l
1162/27 Number of SCCP releases before HANDOVER REQUEST
acknowledging: Incorrect DATA INDICATION received
Name Q3 : signallingReleaseNoBtsBadDataInd
Object : bsc
Function : number of communications in signaling phase released before
HANDOVER REQUEST ACKNOWLEDGE is received in the
incoming handover procedure, because of incorrect DATA
INDICATION message received
Event : receipt of DATA INDICATION other than HANDOVER REQUEST
after receipt of SCCP CONNECTION INDICATION
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : This counter is only incremented in case of incoming external
handovers.
l
1162/28 Number of SCCP releases before HANDOVER REQUEST
acknowledging: Other cases
Name Q3 : signallingReleaseNoBtsOthers
Object : bsc
Function : number of communications in signaling phase released before
HANDOVER REQUEST ACKNOWLEDGE is received in the
incoming handover procedure for other reasons
Event : call in signaling phase released for another reason
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : This counter is only incremented in case of incoming external
handovers.
l
1163/0 Number of communications in signaling phase released: SCCP
disconnection
Name Q3 : signallingReleaseBtsSccpDiscInd
Object : bts
Function : number of communications in signaling phase released because of
SCCP disconnection when a cell is associated with the
communication
l
1163/5 Number of communications in signaling phase released: T3101
elapse
Name Q3 : signallingReleaseBtsT3101
Object : bts
Function : number of communications in signaling phase released because of
T3101 time-out elapse when a cell is associated with the
communication
Event : T3101 time-out elapse before ESTABLISH INDICATION is
received in the immediate assignment procedure
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/6 Number of communications in signaling phase released: T3107
elapse
Name Q3 : signallingReleaseBtsT3107CircDown
Object : bts
Function : number of communications in signaling phase released because of
T3107 time-out elapse when a cell is associated with the
communication
Event : T3107 time-out elapse before ESTABLISH INDICATION is
received in the dedicated channel assignment or intra-bts handover on
SDCCH procedure
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/7 Number of communications in signaling phase released: Ts out of
service (O&M)
Name Q3 : signallingReleaseBtsOmTsRemoval
Object : bts
Function : number of communications in signaling phase released because the
associated with the call is taken out of service
Event : radio time slot withdrawal due to the cell being taken out of service
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/8 Number of communications in signaling phase released: Ts out of
service (faulty equipment)
Name Q3 : signallingReleaseBtsTsRemovalEqptFail
Object : bts
Function : number of communications in signaling phase released because of a
faulty equipment when a cell is associated with the call
Event : radio time slot withdrawal due to a faulty equipment (PCM, etc.)
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/9 Number of communications in signaling phase released: CIC out
of service (O&M)
Name Q3 : signallingReleaseBtsOmCicRemoval
Object : bts
Function : number of communications in signaling phase released because a
terrestrial circuit is taken out of service when a cell is associated with
the communication
Event : CIC withdrawal due to the terrestrial circuit being taken out of service
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/10 Number of communications in signaling phase released: CIC out
of service (faulty equipment)
Name Q3 : signallingReleaseBtsCicRemovalEqptFail
Object : bts
Function : number of communications in signaling phase released because of a
faulty equipment when a cell is associated with the communication
Event : CIC withdrawal due to a faulty equipment (PCM, etc.)
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/11 Number of communications in signaling phase released: Radio
channel blocked (O&M)
Name Q3 : signallingReleaseBtsOmRadioChanBloc
Object : bts
Function : number of communications in signaling phase released because of
radio channel blocking when a cell is associated with the
communication
Event : radio channel blocking by O&M action
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/12 Number of communications in signaling phase released: CALL
CLEARING received
Name Q3 : signallingReleaseBtsCallClearing
Object : bts
Function : number of communications in signaling phase released because of
call clearing when a cell is associated with the communication
Event : receipt of CALL CLEARING because the maximum authorized
distance is exceeded
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/13 Number of communications in signaling phase released: Radio
interface failure
Name Q3 : signallingReleaseBtsCnxFailRadioIntFail
Object : bts
Function : number of communications in signaling phase released because of
radio interface failures when a cell is associated with the
communication
Name Q3 : signallingReleaseBtsReleaseInd
Object : bts
Class : release
Precise
incrementation conditions :
This counter is incremented when the BSC receives a RELEASE
INDICATION on a channel and the channel is not in a release phase.
That means that on A interface, no disconnection has been started (no
CLEAR COMMAND received nor SCCP disconnection).
The RELEASE INDICATION message sent by the BTS is due to the
reception of a DISC frame (LAPDm message) by the BTS from the
mobile (MS).
In the Nortel Networks implementation:
At the BTS level, each time a LAPDm DISC frame is received by the
BTS, a message RELEASE INDICATION is sent by the BTS to the
BSC, unless the link layer is in idle mode (as indicated in
recommendation 08.58).
At the BSC level, in normal release scenario, the counter 1163/16 is
not incremented. In all other cases, the counter 1163/16 is
incremented.
So, the counter C1163/16 takes into account each RELEASE
INDICATION message sent on the SDCCH channel from the BTS
when the BSC is in a state where it has not send to this BTS a RR
CHANNEL RELEASE (triggered by the reception of BSSMAP
CLEAR COMMAND from the MSC).
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Exception conditions : channel in a release phase
Data flows : The following data flow presents the links between signalling
messages exchanged at CM level (between the MSC and the MS),
when the release is initiated by the MS:
MS BSS NSS
CC DISCONNECT
CC RELEASE
CC RELEASE COMPLETE
DESACTIVATE SACCH
DISK
RELEASE INDICATION
UA
RF CHANNEL RELEASE
BSSMAP CLEAR COMPLETE
SCCP RELEASED
l
1163/17 Number of communications in signaling phase released: T200
elapse
Name Q3 : signallingReleaseBtsErrorIndT200
Object : bts
Function : number of communications in signaling phase released because of
T200 time-out elapse in the cell associated with the communication
Event : receipt of ERROR INDICATION: T200 elapsed (N200 + 1) times
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
This counter is related to the Layer2 LAPDm protocol (error
detection + repetition protocol between the BTS and the mobile
(MS)).
When a Layer 2 frame is not acknowledged by the MS before T200
expiration, the BTS sends an Error indication message to the BSC.
After (N200+1) Error indication consecutive messages received for
a call in signaling phase, the BSC increments by one the counter
1163/17.
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : The dataflow below presents an example of Layer 2 LAPDm
exchange. The Level3 messages (measurements reports in SD,
EstInd, SMS, Cyphering, SMS....) are encapsuled in the Layer 2.
MS BTS BSC
SABM
UA
frame1
Ack frame1
frame2
Error indication
T200 expiration
frame2
Error indication
T200 expiration
frame2
Error indication
T200 expiration N200 + 1 error indication + C1163/17
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/20 Number of communications in signaling phase released: CLEAR
COMMAND received
Name Q3 : signallingReleaseBtsClearCommand
Object : bts
Function : number of communications in signaling phase released because of
CLEAR COMMAND received when a cell is associated with the
communication
Event : receipt of CLEAR COMMAND from the MSC on normal end of call
or outgoing inter-bss handover
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “Connection clearing required by the MSC procedure
(communication on SIGNALLING phase)”
DFD “Connection clearing required by the BSC procedure
(communication on SIGNALING phase)”
l
1163/21 Number of communications in signaling phase released: RF
RESOURCE INDICATION received
Name Q3 : signallingReleaseBtsRfResInd
Object : bts
Function : number of communications in signaling phase released because of RF
RESOURCE INDICATION received when a cell is associated with
the communication
Event : receipt of three RF RESOURCE INDICATION messages
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/22 Number of communications in signaling phase released: BSC
chain switchover
Name Q3 : signallingReleaseBtsSwitchOver
Object : bts
Function : number of communications in signaling phase released because of
BSC chain switchovers when a cell is associated with the
communication
Event : BSC chain switchover on receipt of ESTABLISH INDICATION
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/23 Number of communications in signaling phase released: Double
TmodMs elapse
Name Q3 : signallingReleaseBtsTmodMs
Object : bts
Function : number of communications in signaling phase released because of
double TmodMs time-out elapse in the CHANNEL MODE MODIFY
procedure when a cell is associated with the communication
Event : double TmodMs time-out elapse
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/24 Number of communications in signaling phase released: T3103
elapse
Name Q3 : signallingReleaseBtsT3103
Object : bts
Function : number of communications in signaling phase released because of
T3103 time-out elapse in the handover procedure when a cell is
associated with the communication
Event : T3103 time-out elapse
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/25 Number of communications in signaling phase released: T8
elapse
Name Q3 : signallingReleaseBtsT8
Object : bts
Function : number of communications in signaling phase released because of T8
time-out elapse in the inter-bss handover procedure when a cell is
associated with the communication
Event : T8 time-out elapse
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/28 Number of communications in signaling phase released: Other
cases
Name Q3 : signallingReleaseBtsOthers
Object : bts
Function : number of communications in signaling phase released for other
reasons when a cell is associated with the communication
Event : communication in signaling phase released for another reason
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/30 Number of communications in signaling phase released: T11
elapse
Name Q3 : signallingReleaseBtsT11
Object : bts
Function : number of communications in signaling phase released because of
T11 time-out elapse in the queuing procedure when a cell is associated
with the communication
Event : T11 time-out elapse during the queuing procedure
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/32 Number of communications in signaling phase released: TCU
failure
Name Q3 : signallingReleaseBtsCnxFailRemTransFail
Object : bts
Function : number of communications in signaling phase released because of a
TCU failure when a cell is associated with the communication
Event : receipt of CONNECTION FAILURE INDICATION with cause
“remote transcoder failure”
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1163/33 Number of releases while the communication is in “signalling”
phase and cell associated to the communication.
Name Q3 : signallingReleaseCellTbcEdge
Object : bts
Function : Number of releases while the communication is in “signalling” phase
and cell associated to the communication.
Event : TDMA removal due to a EDGE TRX/TDMA optimization
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/0 Number of communications in traffic phase released: SCCP
disconnection
Name Q3 : trafficReleaseSccpDiscInd
Object : bts
Function : number of communications in traffic phase released because of SCCP
disconnection
Event : receipt of SCCP DISCONNECTION INDICATION from the MSC
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/1 Number of communications in traffic phase released: Reset from
the MSC
Name Q3 : trafficReleaseReset
Object : bts
Function : number of communications in traffic phase released because of reset
from the MSC
Event : receipt of RESET from the MSC
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/2 Number of communications in traffic phase released: Reset
circuit downlink
Name Q3 : trafficReleaseResetCirc
Object : bts
Function : number of communications in traffic phase released because of reset
circuit in the Downlink direction
Event : receipt of RESET CIRCUIT DOWNLINK from the MSC
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/3 Number of communications in traffic phase released: SCCP
DATA REFUSAL received
Name Q3 : trafficReleaseSccpDataRefusal
Object : bts
Function : number of communications in traffic phase released because of SCCP
data refusal
Event : receipt of SCCP DATA REFUSAL from the MSC
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/6 Number of communications in traffic phase released: T3107
elapse
Name Q3 : trafficReleaseT3107CircDown
Object : bts
Function : number of communications in traffic phase released because of T3107
time-out elapse
Event : T3107 time-out elapse in the traffic establishment procedure
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/7 Number of communications in traffic phase released: Ts out of
service (O&M)
Name Q3 : trafficReleaseOmTsRemoval
Object : bts
Function : number of communications in traffic phase released because of the
cell being taken out of service
Event : radio time slot withdrawal due to the cell being taken out of service
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/8 Number of communications in traffic phase released: Ts out of
service (faulty equipment)
Name Q3 : trafficReleaseTsRemovalEqptFail
Object : bts
Function : number of communications in traffic phase released because of a
faulty equipment
Event : radio time slot withdrawal due to a faulty equipment (PCM, etc.)
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/9 Number of communications in traffic phase released: CIC out of
service (O&M)
Name Q3 : trafficReleaseOmCicRemoval
Object : bts
Function : number of communications in traffic phase released because of a
terrestrial circuit being taken out of service
Event : CIC withdrawal due to the terrestrial circuit being taken out of service
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/10 Number of communications in traffic phase released: CIC out of
service (faulty equipment)
Name Q3 : trafficReleaseCicRemovalEqptFail
Object : bts
Function : To list the number of communications in traffic phase released
because of a faulty equipment. Creating a synthetic counter to work
on a ration, not on absolute values.
Event : CIC withdrawal due to a faulty equipment (PCM, etc.)
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/11 Number of communications in traffic phase released: Radio
channel blocked (O&M)
Name Q3 : trafficReleaseOmRadioChanBloc
Object : bts
Function : number of communications in traffic phase released because of radio
channel blocking
Event : radio channel blocking by O&M action
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/12 Number of communications in traffic phase released: CALL
CLEARING received
Name Q3 : trafficReleaseCallClearing
Object : bts
Function : number of communications in traffic phase released because of call
clearing
Event : receipt of a call clearing request
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/13 Number of communications in traffic phase released: Radio
interface failure
Name Q3 : trafficReleaseCnxFailRadioIntFail
Object : bts
Function : number of communications in traffic phase released because of radio
interface failures
Event : receipt of CONNECTION FAILURE INDICATION with Abis cause
“radio interface failure”
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/14 Number of communications in traffic phase released: Radio link
failure
Name Q3 : trafficReleaseCnxFailRadioLinkFail
Object : bts
Function : number of communications in traffic phase released because of radio
link failures
Event : receipt of CONNECTION FAILURE INDICATION with Abis cause
“radio link failure”
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/16 Number of communications in traffic phase released: RELEASE
INDICATION received
Name Q3 : trafficReleaseReleaseInd
Object : bts
Function : number of communications in traffic phase released because of
RELEASE INDICATION received
Event : receipt of RELEASE INDICATION from the BTS
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
This counter is incremented when the BSC receives a RELEASE
INDICATION on a channel and the channel is not in a release phase.
That means that on A interface, no disconnection has been started (no
CLEAR COMMAND received nor SCCP disconnection).
The RELEASE INDICATION message sent by the BTS is due to the
reception of a DISC frame (LAPDm message) by the BTS from the
mobile (MS).
In the Nortel Networks implementation:
At the BTS level, each time a LAPDm DISC frame is received by the
BTS, a message RELEASE INDICATION is sent by the BTS to the
BSC, unless the link layer is in idle mode (as indicated in
recommendation 08.58).
At the BSC level, in normal release scenario, the counter 1164/16 is
not incremented. In all other cases, the counter 1164/16 is
incremented.
So, the counter C1164/16 takes into account each RELEASE
INDICATION message sent on the TCH channel from the BTS when
the BSC is in a state where it has not send to this BTS a RR
CHANNEL RELEASE (triggered by the reception of BSSMAP
CLEAR COMMAND from the MSC).
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : The following data flow presents the links between signalling
messages exchanged at CM level (between the MSC and the MS),
when the release is initiated by the MS:
MS BSS NSS
CC DISCONNECT
CC RELEASE
CC RELEASE COMPLETE
DESACTIVATE SACCH
DISK
RELEASE INDICATION
UA
RF CHANNEL RELEASE
BSSMAP CLEAR COMPLETE
SCCP RELEASED
l
1164/17 Number of communications in traffic phase released: T200 elapse
Name Q3 : trafficReleaseErrorIndT200
Object : bts
Function : number of communications in traffic phase released because of T200
time-out elapse
Event : receipt of ERROR INDICATION: T200 elapsed (N200 + 1) times
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
This counter is related to the Layer2 LAPDm protocol (error
detection + repetition protocol between the BTS and the mobile
(MS)).
When a Layer 2 frame is not acknowledged by the MS before T200
expiration, the BTS sends an Error indication message to the BSC.
After (N200+1) Error indication consecutive messages received for
a call in traffic phase, the BSC increments by one the counter
1164/17.
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : The dataflow below presents an example of Layer 2 LADm exchange.
The Level3 messages (measurements reports in SD, EstInd, SMS,
Cyphering, SMS....) are encapsuled in the Layer 2.
MS BTS BSC
SABM
UA
frame1
Ack frame1
frame2
Error indication
T200 expiration
frame2
Error indication
T200 expiration
frame2
Error indication
T200 expiration N200 + 1 error indication + C1164/17
Event : receipt of CLEAR COMMAND from the MSC on normal end of call
or outgoing inter-bss handover
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Connection clearing required by the MSC procedure
(communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Connection clearing required by the BSC procedure
(communication on TRAFFIC phase)”
l
1164/21 Number of communications in traffic phase released: RF
RESOURCE INDICATION received
Name Q3 : trafficReleaseRfResInd
Object : bts
Function : number of communications in traffic phase released because of RF
RESOURCE INDICATION received
Event : receipt of three RF RESOURCE INDICATION messages
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/23 Number of communications in traffic phase released: TmodMs
elapse
Name Q3 : trafficReleaseTmodMs
Object : bts
Function : number of communications in traffic phase released because of
TmodMs time-out elapse
Event : double TmodMs time-out elapse in the CHANNEL MODE MODIFY
procedure
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/24 Number of communications in traffic phase released: T3103
elapse
Name Q3 : trafficReleaseT3103
Object : bts
Function : number of communications in traffic phase released because of T3103
time-out elapse
Event : T3103 time-out elapse in the handover procedure
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/25 Number of communications in traffic phase released: T8 elapse
Name Q3 : trafficReleaseT8
Object : bts
Function : number of communications in traffic phase released because of T8
time-out elapse
Event : T8 time-out elapse in the inter-bss handover procedure
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1164/28 Number of communications in traffic phase released: Other cases
Name Q3 : trafficReleaseOthers
Object : bts
Function : To list the number of communications in traffic phase released
because of lack of Ater uplink TRAU frame synchronization. These
counters are the indications of a loss of frame synchronization either
because of a loopback on the transmission line, or poor quality of the
backhaul facilities.
Event : Receipt of a Release Indication message from the TCU with cause set
to ”Synchro frame error “.
Type : raw permanent
Class : release
Source : recorded by the BSC. Counter 1164/28 increments on the uplink
(BTS-->TCU) when the TCU detects the fault.
Precise
incrementation conditions :
Mechanism of Counter
This is managed by the TCU 3000; A TRAU can be in one of two
states, Idle or Active, and is considered to be synchronized, depending
on its state, when:
Release mechanism: At the fault detection, the TCU 3000 sends to the
BSC a Release Indication message (cause= ”Synchro trame error”). At
reception of this message, the BSC:
TRM fault,
PCM A or ATER fault,
Lock of PCM A or ATER.
Detection process :
BSC 3000 Notifications:
On the BSC 3000, an anomaly is recorded for each kind of call drop:
5620 for calls dropped by the TCU (recorded once per 20
drops)
5621 for calls dropped by the BTS (recorded once per
100 drops)
To check for these errors, retrieve from the BSC the fault files located
in /OMU/share/fault (with the .txt extension) for the relevant days.
Please contact GNTS to get these files and analyze them.
Counters also exist on the BSC 3000/TCU 3000 which can be used to detect
scenarios where calls are being abnormally dropped.
1. On the active server under omc login, save the original synthetic counter formulae
configuration file to the default browsed with Synthetic Counters Editor location
by applying the following command:
(omc)% cp -p /OMC/data/custo_config/config/bss_operator_formulas.cfg
/OMC/data/custo_config/obs/synthetic/
Note: This command is used for safety reasons. It avoids overwriting any
synthetic counters that were previously created.
This translates to the syntax below, which is used to set up Synthetic Counters.
<Desired Name> bts [:on,Threshold_Alarm_Cleared,Threshold_Alarm_Raised]=<Formula>
3. Check raw counters used in the synthetic counter formula (on the server). List the
raw counters used in the synthetic counter formula.
a) Select the concerned bsc, click on the mouse right button, and choose
“display”
b) On the list proposed choose bsc counter list 2 for OFS (fast statistic
counter)
c) In the Mmi window displayed or in sessionlog result, check that all raw
counters are present
4. Make PM tasks calculate values of synthetic counter (on the server).
a) Select “Performance menu”, item “load formula”, and choose
“Observation type: faststatistics” and then “apply”
5. Control results:
a) Check that observation files are generated (on the server) under:
/MD/obs/os_ftam/<currentday>/<bsc number>
b) Control that alarms are raised (use alarm Criteria to generate alarms)
• Click on “Apply”
6. Set CriteriaEventtype to alarmNotification
7. If OMC--R is V14.3 then:
• Set startAlarm filter to faultNumber = 31200
• Set endAlarm filter to perceived severity = CLEARED
Examples
The above Syntax will raise an Alarm if the Counter Value is more than or equal to
50 and will Clear the alarm if the Counter Value is less than or equal to 20.
In this example a major alarm is raised if counter 1164/28
(trafficReleaseCnxFailRemTrans) value is greater than 50:
Common Causes:
Failing PCM or Timeslot in the path between the BTS and TCU.
Trap of DSP that manages the call (TRM board): Check if you
have any 2032 fault on TRM of your BSC.
Synchronization of BSC/TCU with the MSC clock: Check the
synchronization of BSC 3000/TCU/MSC
- V15.0 using a ”display dynamic data” on BSC 3000 and on
TCU 3000 objects.
- Prior to V15.0, using notifications 2019.
The problem could be caused by the ABIS or ATER PCM, (or the BSC), and
may affect an entire PCM or, one or more individual Timeslots. Each
64Kbps ABIS PCM timeslot is divided into four 16Kbps sub--channels.
Therefore each TDMA, consisting of 8 channels, uses two adjacent ABIS
64Kbps TS.
ABIS
X X X X Y Y Y Y
Timeslot
Channel 3 4 5 6 7 0 1 2
Therefore: A failure of one 64Kbps timeslot will affect four radio channels.
PCM.
c. For the failing PCM, check which 16Kbps sub--channels are
impacted: Is it all 4 sub--channels associated with one
timeslot, or only 1 or 2 sub--channels?
2. Check for any PCM related notifications for the PCM’s found in
step 1, treat these symptoms first then verify if counters are still incremented
3. Confirm failing path:
a. Try to swap PCMs, or lock one PCM at a time.
b. Try to lock impacted Radio Channels.
c. Determine if the counters are still incremented.
a. Check the DACS board that manages the PCM and the DACS
configuration.
b. The DACS (and many other types of transmission equipment)
will often have counters indicating errors, errored seconds,
BPV’s, slips, or Frame errors. Use these to localize the source of
the problem. Note that, depending on the type of DACS, it may
re--frame the signal, which would tend to ”mask” alarms and
some types of errors (slips, notably).
c. All transmission facilities should be configured to use
appropriate zero--code suppression (i.e., B8ZS for DS1
facilities).
5. Using suitable test equipment, perform end--to--end quality test
of failing PCM.( i.e. BERT test etc). Ensuring that all Timeslots
are checked.
6. If the failing PCM’s are associated with the same LSA perform
a SWACT of the associated IEM.
NOTES:
If layer 1 does not detect a fault, (for example a looped PCM) and there is no
LAPD carried on the failing timeslot(s), then there may be no other
indication of a PCM problem other than the counters 1164/28 and 1164/32.
A call dropped by the TCU could also lead to the BTS detecting a problem
and incrementing 1164/32, therefore it is not unusual to see both counters
incrementing.
Due to the fact that the call is dropped after 6 secs it can be difficult to
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Mechanism of Counter
The BTS is synchronized when the following frames are received on
the ABIS PCM:
Correct speech frames (FS, EFR, FR and HR AMR,
circuit data, PEC frames)
SID, idle speech, idle data.
The BTS loses or does not find its frame synchronization in the
following cases:
Detection process :
BSC 3000 Notifications:
On the BSC 3000, an anomaly is recorded for each kind of call drop:
5620 for calls dropped by the TCU (recorded once per 20 drops)
5621 for calls dropped by the BTS (recorded once per 100
drops)
To check for these errors, retrieve from the BSC the fault files located in
/OMU/share/fault (with the .txt extension) for the relevant days. Please
contact GNTS to get these files and analyze them.
Common Causes:
Failing PCM or Timeslot in the path between the TCU and the
BTS.
The problem could be caused by the ABIS or ATER PCM, (or the BSC), and
may affect an entire PCM or, one or more individual Timeslots. Each
64Kbps ABIS PCM timeslot is divided into four 16Kbps sub--channels.
Therefore each TDMA, consisting of 8 channels, uses two adjacent ABIS
64Kbps TS.
ABIS
X X X X Y Y Y Y
Timeslot
Channel 3 4 5 6 7 0 1 2
Therefore: A failure of one 64Kbps timeslot will affect four radio channels.
a. Check the DACS board that manages the PCM and the DACS
configuration.
b. The DACS (and many other types of transmission equipment)
will often have counters indicating errors, errored seconds,
BPV’s, slips, or Frame errors. Use these to localize the source of
the problem. Note that, depending on the type of DACS, it may
re--frame the signal, which would tend to ”mask” alarms and
some types of errors (slips, notably).
c. All transmission facilities should be configured to use
appropriate zero--code suppression (i.e., B8ZS for DS1
facilities).
5. Using suitable test equipment, perform end--to--end quality test
of failing PCM.( i.e. BERT test etc). Ensuring that all Timeslots
are checked.
6. If the failing PCM’s are associated with the same LSA perform
a SWACT of the associated IEM.
NOTES:
If layer 1 does not detect a fault, (for example a looped PCM) and there is no
A call dropped by the TCU could also lead to the BTS detecting a problem
and incrementing 1164/32, therefore it is not unusual to see both counters
incrementing.
Due to the fact that the call is dropped after 6 secs it can be difficult to
identify a failing PCM/TS in real--time.
Counters also exist on the BSC 3000/TCU 3000 which can be used to detect
scenarios where calls are being abnormally dropped.
8713 (callDropTrafficRadio) provides the ratio of the number of
communications abnormally released within the signalling phase in the cell.
8714 (signallingReleaseRatio) provides the ratio of the number of
communications abnormally released within the traffic phase in the cell.
To ensure OMC--R notification when calls are being abnormally dropped, use the
following procedures.
1. On the active server under omc login, save the original synthetic counter formulae
configuration file to the default browsed with Synthetic Counters Editor location
by applying the following command:
(omc)% cp -p /OMC/data/custo_config/config/bss_operator_formulas.cfg
/OMC/data/custo_config/obs/synthetic/
Note: This command is used for safety reasons. It avoids overwriting any
synthetic counters that were previously created.
This translates to the syntax below, which is used to set up Synthetic Counters.
<Desired Name> bts [:on,Threshold_Alarm_Cleared,Threshold_Alarm_Raised]=<Formula>
3. Check the raw counters used in the synthetic counter formula (on the server). List
the raw counters used in the synthetic counter formula.
a) Select the concerned bsc, click on the mouse right button, and choose
“display”
b) On the list proposed choose bsc counter list 2 for OFS (fast statistic
counter)
c) In the Mmi window displayed or in sessionlog result, check that all raw
counters are present
4. Make PM tasks calculate values of synthetic counter (on the server).
a) Select “Performance menu”, item “load formula”, and choose
“Observation type: faststatistics” and then “apply”
5. Control results:
a) Check that observation files are generated (on the server) under:
/MD/obs/os_ftam/<currentday>/<bsc number>
b) Control that alarms are raised (use alarm Criteria to generate alarms)
• day intervention
• night intervention
• particular intervention
5. In Object Instance:
• Set Exploration type object instance
• Click on “addItem” and then “Modify”
• Set:
– bsc all
– btsSm all
– bts all
• Click on “Apply”
• Click on “Apply”
6. Set CriteriaEventtype to alarmNotification
7. If OMC--R is V14.3 then:
• Set startAlarm filter to faultNumber = 31200
• Set endAlarm filter to perceived severity = CLEARED
If OMC--R is v15.0 then:
• Set startAlarm filter to faultNumber = 31200 & (!perceived severity =
CLEARED)
• Set endAlarm filter to perceived severity = 31200 & perceived severity =
CLEARED
8. Click on “Apply”
How to make the Alarm Criteria active
1. Select “OMC--R object” in Mmi
2. Click on right button choose “Display/set”
3. Select “Mode/Set”
4. Change alarm criteria from day configuration to night configuration, then click
on “Apply”
5. Change alarm criteria from night configuration to day configuration, then click
on “Apply”
Examples
The above Syntax will raise an Alarm if the Counter Value is more than or equal to
50 and will Clear the alarm if the Counter Value is less than or equal to 20.
l
1165 Number of handover requests not processed: Tchoke in-progress
Name Q3 : hoIndicationNotTreatedTchoke
Object : bts
Function : number of handover requests not processed by the BSC because of
Tchoke timer active
Event : receipt of HANDOVER INDICATION while the Tchoke timer is
running
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1167 Number of unsuccessful outgoing intra handovers on TCH to a
non-heading cell without reestablishment in the serving cell
Name Q3 : hoUnsuccessOutgoingIntraBssNAttemptTch
Object : bts
Function : number of unsuccessful outgoing intra-bss handovers on TCH
towards a cell that is not heading the list of eligible cells without
reestablishment in the current serving cell
Event : receipt of HANDOVER FAILURE on T3103 time-out elapse
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : the list is reorganized by the BSC since Ho decision function. It may
not be the same order as the one received from the L1M
l
1168 Number of unsuccessful outgoing intra handovers on SDCCH to
a non-heading cell without reestablishment in the serving cell
Name Q3 : hoUnsuccessOutgoingIntraBssNAttemptSdcch
Object : bts
Function : number of unsuccessful outgoing intra-bss handovers on SDCCH
towards a cell that is not heading the list of eligible cells without
reestablishment in the current serving cell
Event : receipt of HANDOVER FAILURE on T3103 time-out elapse
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Note : the list is reorganized by the BSC since Ho decision function. It may
not be the same order as the one received from the L1M
l
1169 Number of unsuccessful outgoing inter handovers on TCH to a
non-heading cell without reestablishment in the serving cell
Name Q3 : hoUnsuccessOutgoingInterBssNAttemptTch
Object : bts
Function : number of unsuccessful outgoing inter-bss handovers on TCH
towards a cell that is not heading the list of eligible cells without
reestablishment in the current serving cell
l
1172/0 Number of fallbacks from a data rate to other data rates for TCB
lack of resources cause
Name Q3 : dataNtRateFbTcbResLack
Object : bsc
Function : number of fallbacks from a data rate to other data rates for TCB lack
of resources cause
Event : response from terrestrial allocator
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1172/1 Number of fallbacks from a data rate to other data rates for non
allowed TCB configuration cause
Name Q3 : dataNtRateFbTcbConfNotAllowed
Object : bsc
Function : number of fallbacks from a data rate to other data rates for non
allowed TCB configuration cause
Event : configuration mismatch
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1191/0 Number of channel allocation requests: Cause 000
Name Q3 : channelRequestCause000
Object : bts
Function : number of channel allocation requests in the cell with cause 000
Event : receipt of CHANNEL REQUIRED:
Phase I = all other cases
Phase II = location update request (0000), other procedures using
an SDCCH (0001)
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1191/1 Number of channel allocation requests: Cause 001
Name Q3 : channelRequestCause001
Object : bts
Function : number of channel allocation requests in the cell with cause 001
Event : receipt of CHANNEL REQUIRED:
Phase I = nonsignificant
Phase II = reply to a paging request
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1191/2 Number of channel allocation requests: Cause 010
Name Q3 : channelRequestCause010
Object : bts
Function : number of channel allocation requests in the cell with cause 010
Event : receipt of CHANNEL REQUIRED:
Phase I = nonsignificant
Phase II = transmission of speech (0100) or data (0101) on a
TCH/FR by a mobile
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1191/3 Number of channel allocation requests: Cause 011
Name Q3 : channelRequestCause011
Object : bts
Function : number of channel allocation requests in the cell with cause 011
Event : receipt of CHANNEL REQUIRED:
Phase I = nonsignificant
Phase II = call reestablishment on a TCH/FR
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1191/4 Number of channel allocation requests: Cause 100
Name Q3 : channelRequestCause100
Object : bts
Function : number of channel allocation requests in the cell with cause 100
Event : receipt of CHANNEL REQUIRED for a reply to a paging request
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1191/5 Number of channel allocation requests: Cause 101
Name Q3 : channelRequestCause101
Object : bts
Function : number of channel allocation requests in the cell with cause 100
Event : receipt of CHANNEL REQUIRED for an emergency call
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1191/6 Number of channel allocation requests: Cause 110
Name Q3 : channelRequestCause110
Object : bts
Function : number of channel allocation requests in the cell with cause 110
Event : receipt of CHANNEL REQUIRED for a call reestablishment
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1191/7 Number of channel allocation requests: Cause 111
Name Q3 : channelRequestCause111
Object : bts
Function : number of channel allocation requests in the cell with cause 111
Event : receipt of CHANNEL REQUIRED with the following cause:
Phase I = any services requested by the mobile (MOC, SMS, SS)
Phase II = MOC (Mobile Originating Call) service on TCH/FR
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1192/2 Number of successful immediate assignments: Cause 010
Name Q3 : immediateAssignmentSuccessCause010
Object : bts
Function : number of immediate assignments with cause 010 satisfied
Event : transmission of IMMEDIATE ASSIGNMENT with the following
cause:
Phase I = nonsignificant
Phase II = transmission of speech (0100) or data (0101) on a
TCH/FR by a mobile
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Immediate assignment procedure (normal completion)”
DFD “GPRS procedure preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “SMS procedure (SMS established by the MS)”
l
1192/3 Number of successful immediate assignments: Cause 011
Name Q3 : immediateAssignmentSuccessCause011
Object : bts
Function : number of immediate assignments with cause 011 satisfied
l
1192/4 Number of successful immediate assignments: Cause 100
Name Q3 : immediateAssignmentSuccessCause100
Object : bts
Function : number of immediate assignments with cause 100 satisfied
Event : transmission of IMMEDIATE ASSIGNMENT on receipt of
CHANNEL REQUEST with cause “paging request”
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Immediate assignment procedure (normal completion)”
DFD “GPRS procedure preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “SMS procedure (SMS established by the MS)”
l
1192/5 Number of successful immediate assignments: Cause 101
Name Q3 : immediateAssignmentSuccessCause101
Object : bts
Function : number of immediate assignments with cause 101 satisfied
Event : transmission of IMMEDIATE ASSIGNMENT on receipt of
CHANNEL REQUEST with cause “emergency call”
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1192/6 Number of successful immediate assignments: Cause 110
Name Q3 : immediateAssignmentSuccessCause110
Object : bts
Function : number of immediate assignments with cause 110 satisfied
Event : transmission of IMMEDIATE ASSIGNMENT on receipt of
CHANNEL REQUEST with cause “call reestablishment”
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Immediate assignment procedure (normal completion)”
DFD “GPRS procedure preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “SMS procedure (SMS established by the MS)”
l
1192/7 Number of successful immediate assignments: Cause 111
Name Q3 : immediateAssignmentSuccessCause111
Object : bts
Function : number of immediate assignments with cause 111 satisfied
Event : transmission of IMMEDIATE ASSIGNMENT on receipt of
CHANNEL REQUEST with the following cause:
Phase I = all services requested by the mobile (MOC, SMS, SS)
Phase II = MOC (Mobile Originating Call) service on TCH/FR
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Immediate assignment procedure (normal completion)”
DFD “GPRS procedure preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “SMS procedure (SMS established by the MS)”
l
1193/0 Number of ESTABLISH INDICATION messages in
establishment phase received for paging requests
Name Q3 : estabIndicSignallingPagingRes
Object : bts
Function : number of ESTABLISH INDICATION messages received on
SDCCH or TCH if no SDCCH is available, for replies to paging
requests
l
1193/2 Number of ESTABLISH INDICATION messages in
establishment phase received for call reestablishments
Name Q3 : estabIndicSignallingReEstab
Object : bts
Function : number of ESTABLISH INDICATION messages received on
SDCCH or TCH in primo-allocations, for call reestablishments
Event : receipt of ESTABLISH INDICATION for a call reestablishment
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Immediate assignment procedure (normal completion)”
DFD “GPRS procedure preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Dedicated channel assignment modify procedure (normal
completion)”
l
1193/3 Number of ESTABLISH INDICATION messages in
establishment phase received for IMSI detachments
Name Q3 : estabIndicSignallingImsiDetach
Object : bts
Function : number of ESTABLISH INDICATION messages received on
SDCCH or TCH if no SDCCH is available, for IMSI detachments
Event : receipt of ESTABLISH INDICATION for an IMSI detach request
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Immediate assignment procedure (normal completion)”
DFD “GPRS procedure preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Dedicated channel assignment modify procedure (normal
completion)”
l
1193/4 Number of ESTABLISH INDICATION messages in
establishment phase received for mobile originating calls
Name Q3 : estabIndicSignallingMoc
Object : bts
Function : number of ESTABLISH INDICATION messages received on
SDCCH or TCH if no SDCCH is available, for mobile originating
calls
Event : receipt of ESTABLISH INDICATION for a mobile originating call
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Dedicated channel assignment modify procedure (normal
completion)”
l
1193/5 Number of ESTABLISH INDICATION messages in
establishment phase received for urgent calls
Name Q3 : estabIndicSignallingEmergency
Object : bts
Function : number of ESTABLISH INDICATION messages received on
SDCCH or TCH if no SDCCH is available, for emergency calls
Event : receipt of ESTABLISH INDICATION for an emergency call
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1193/7 Number of ESTABLISH INDICATION messages in
establishment phase received for other services
Name Q3 : estabIndicSignallingSuppService
Object : bts
Function : number of ESTABLISH INDICATION messages received on
SDCCH or TCH if no SDCCH is available, for supplementary service
Event : receipt of ESTABLISH INDICATION for a supplementary service
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Immediate assignment procedure (normal completion)”
DFD “GPRS procedure preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Dedicated channel assignment modify procedure (normal
completion)”
l
1196 Number of ESTABLISH INDICATION messages in
establishment phase received for Phase II mobiles
Name Q3 : estabIndicSigPhase2
Object : bts
Function : number of ESTABLISH INDICATION messages received on
SDCCH, or TCH in primo-allocations, or TCH if no SDCCH is
available, for Phase II mobiles
Event : receipt of ESTABLISH INDICATION for a Phase II mobile
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1197/0 Number of channels activated for speech: Full Rate Algorithm
Name Q3 : channelActivateSpeechFullRate
Object : bts
Function : number of speech channels using the Full-Rate algorithm, activated in
the cell for the observation period
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “speech”
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1197/1 Number of channels activated for speech: Enhanced Full Rate
Algorithm
Name Q3 : channelActivateSpeechEnhancedFullRate
Object : bts
Function : number of speech channels using the Enhanced Full-Rate algorithm,
activated in the cell for the observation period
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “speech”
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1198 Duration of maximum Downlink power use on busy TCH/FRs or
preempted PDTCHs
Name Q3 : downlinkPowerCtrlMaxTchMoy
downlinkPowerCtrlMaxTchMax Maximum duration
downlinkPowerCtrlMaxTchCum Total duration
downlinkPowerCtrlMaxTchEch Number of samples
Object : bts
Function : average duration ( = total duration divided by the number of samples)
and maximum duration of maximum Downlink power use on the cell
TCH/FRs or preempted PDTCHs in the observation period
Event : start/end of maximum TCH Downlink power use:
start: start timer
end:
• stop and read timer
• store its peak value
• add it to the total of maximum Downlink power use durations
on TCH/FRs or preempted PDTCHs in the observation period
• step up by one the number of samples
Type : raw permanent
Class : L1M
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “queuing of the assignment procedure (normal completion)
DFD “connection clearing required by the MSC procedure
(normal completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Connection clearing required by the BSC procedure
(communication on TRAFFIC phase)”
l
1199 Duration of maximum Uplink power use on busy TCH/FRs or
preempted PDTCHs
Name Q3 : uplinkPowerCtrlMaxTchMoy
uplinkPowerCtrlMaxTchMax . . . . Maximum duration
uplinkPowerCtrlMaxTchCum . . . . Total duration
uplinkPowerCtrlMaxTchEch . . . . . Number of samples
Object : bts
Function : average duration ( = total duration divided by the number of samples)
and maximum duration of maximum Uplink power use on the cell
TCH/FRs or preempted PDTCHs for the observation period
Event : start/end of maximum TCH Uplink power use:
start: start timer
end:
• stop and read timer
• store its peak value
• add it to the total of maximum Uplink power use durations on
TCH/FRs or preempted PDTCHs in the observation period
• step up by one the number of samples
Type : raw permanent
Class : L1M
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “queuing of the assignment procedure (normal completion)
DFD “connection clearing required by the MSC procedure
(normal completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Radio channel release RELEASE INDICATION procedure
(normal completion)”
DFD “Radio channel release RELEASE INDICATION procedure
(normal completion)”
DFD “Connection clearing required by the BSC procedure
(communication on TRAFFIC phase)”
l
1200 Number of handovers on TCH executed
Name Q3 : hoNcellsExecution
Object : adjacentCellHandOver
Function : number of attempts to execute handovers on TCH from a serving cell
to its neighbors
l
1204/1 Number of unsuccessful outgoing handovers on TCH: Time-out
elapse
Name Q3 : hoNcellsUnsuccessTchTimer
Object : adjacentCellHandOver
Function : number of unsuccessful outgoing intra- and inter-bss handovers on
TCH because of T3103 time-out elapse
Event : T3103 time-out elapse
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1204/2 Number of unsuccessful outgoing handovers on TCH: Other
cases
Name Q3 : hoNcellsUnsuccessTchOther
Object : adjacentCellHandOver
Function : number of unsuccessful outgoing intra- and inter-bss handovers on
TCH because of other reasons
Event : receipt of CLEAR COMMAND from the MSC with a cause different
from “Handover successful” or “Call Control”
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1205/0 Number of unsuccessful outgoing handovers on SDCCH: Back to
old channel
Name Q3 : hoNcellsUnsuccessSdcchChlR
Object : adjacentCellHandOver
Function : number of unsuccessful outgoing intra- and inter-bss handovers on
SDCCH with the mobile returning to the old channel
Event : receipt of HANDOVER FAILURE before T3103 time-out elapse (the
serving cell is unable to transfer the mobile to the new channel)
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1205/1 Number of unsuccessful outgoing handovers on SDCCH:
Time-out elapse
Name Q3 : hoNcellsUnsuccessSdcchTimer
Object : adjacentCellHandOver
Function : number of unsuccessful outgoing intra- and inter-bss handovers on
SDCCH because of T3103 time-out elapse
Event : T3103 time-out elapse
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1205/2 Number of unsuccessful outgoing handovers on SDCCH: Other
cases
Name Q3 : hoNcellsUnsuccessSdcchOther
Object : adjacentCellHandOver
Function : number of unsuccessful outgoing intra- and inter-bss handovers on
SDCCH for other reasons
Event : receipt of CLEAR_COMMAND with a cause different from
“Handover successful” or “Call Control” coming from the MSC
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1206/0 Number of handovers and assignment for which the initial
request in EFR speech algorithm is degraded into FR speech
algorithm
Name Q3 : speechAlgoFallBack
Object : bsc
Function : number of handovers and assignment for which the initial request in
EFR speech algorithm is degraded into FR speech algorithm only in
case of the BSC has a CIC bearing EFR and other CICs not bearing
EFR and if all CICs bearing EFR are already allocated
l
1207 Number of immediate assignments for multiband mobiles
Name Q3 : immediateAssignmentMultiband
Object : bts
Function : number of call establishments for multiband mobiles (external
incoming handover requests are not included)
Event : receipt of the first CLASSMARK_CHANGE message from a mobile
with classmark 3 multiband data, when
Early_Classmark_Sending_Controlled is “true”
Type : raw permanent
Class : assignation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1208 Number of outgoing handovers requested by dualband mobiles
from the main frequency band to the second frequency band of
the network
Name Q3 : hoRequestOutgoingMbandEbandMsDualb (V12)
hoRequestOutgoingMultiband (V10 & V11)
Object : bts
Function : number of outgoing, intra-bss or inter-bss handovers, on TCH,
requested from the main frequency band to the second frequency
band of the network
Event : attempt to select a cell that belongs to the second frequency band in
the list of eligible cells
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Note : The target resource is in the second frequency band whereas the
originated resource is in the main frequency band of the network.
l
1209 Number of successful outgoing handovers for dualband mobiles
from the main frequency band to the second frequency band of
the network
Name Q3 : hoSuccessOutgoingMbandEbandMsDualb (V12)
hoSuccessOutgoingMultiband (V10 & V11)
Object : bts
Function : number of successful outgoing, intra-bss or inter-bss handovers, on
TCH, from the main frequency band to the second frequency band of
the network
l
1502 Number of BSSMAP messages sent
Name Q3 : aNonTransparentUp
Object : bsc
Function : number of non transparent messages sent by the BSC to the MSC
Event : transmission of SCCP CONNECTION REQUEST, SCCP DATA
REQUEST, or SCCP UNIT DATA REQUEST
Type : raw permanent
Class : A interface
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (no available resource for a PDTCH
preemption)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “immediate assignment procedure (normal completion)
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “dedicated channel assignment procedure (no Resource
available and queuing not activated)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “Immediate assignment paging procedure (normal
completion)”
l
1506/1 Number of rejected incoming external handover requests due to
overload situation
Name Q3 : aintOverloadRejectedOpIncomingExtHoReq
Object : bsc
Function : number of rejected external handover requests due to overload
situation
Event : receipt of an incoming external handover request when at least one
SS7 TMU, interface Node, or local TMU board is in overload
situation
Type : raw permanent
Class : equipment
Source : recorded by the BSC
Feature : Overload defense mechanism based on real load (FM877-- V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1506/2 Number of rejected VBS/VGCS setup requests.
Name Q3 : aintOverLoadRejectedOpVbsVgcsSetup
Object : bsc
Function : number of rejected VBS/VGCS setup requests due to overload
situation
Event : receipt of a VBS/VGCS setup request when at least one SS7 TMU,
interface Node, or local TMU board is in overload situation
Type : raw permanent
Class : equipment
Source : recorded by the BSC
Feature : Overload defense mechanism based on real load (FM877-- V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1506/3 number of rejected VBS/VGCS assignment requests
Name Q3 : aintOverLoadRejectedOpVbsVgcsAssignment
Object : bsc
Function : number of rejected VBS/VGCS assignment requests.
Event : receipt of a VBS/VGCS assignment request when at least one SS7
TMU, interface Node, or local TMU board is in overload situation
Type : raw permanent
Class : equipment
Source : recorded by the BSC
Feature : Overload defense mechanism based on real load (FM877-- V12)
l
1506/4 number of perform location requests due to overload situation
Name Q3 : aintOverLoadRejectedOpPerformLocationReq
Object : bsc
Function : number of perform location requests requests.
Event : receipt of a perform location request when at least one SS7 TMU,
interface Node, or local TMU board is in overload situation
Type : raw permanent
Class : equipment
Source : recorded by the BSC
Feature : CRe Q00590141
Note : V15.1R counter
l
1600 Connection duration of TCH/FRs or preempted PDTCH
Name Q3 : connectionDurationTchMoy
connectionDurationTchMax . . . . . Maximum connection duration
connectionDurationTchCum . . . . . Total connection duration
connectionDurationTchEch . . . . . . Number of samples
connectionDurationTchTrZoneMoy
connectionDurationTchTrZoneMax Maximum connection duration
connectionDurationTchTrZoneCum Total connection duration
connectionDurationTchTrZoneEch Number of samples
Object : bts/transceiverZone
Function : average duration ( = total duration divided by the number of samples)
and maximum duration of TCH/FR or preempted PDTCH
connections in the inner or the outer zone of the cell, for the
observation period, expressed in ms
Event : TCH/FR or preempted PDTCH connection/disconnection
connection: start timer
disconnection:
• stop and read timer
• store its peak value
• add it to the total of maximum TCH/FR or preempted PDTCH
connection durations in the observation period
• step up by one the number of samples
Type : raw permanent
Class : L1M
Source : recorded by the BSC
Note : This counter starts at the beginning of transmission of the SACCH
blocks on TCH/FR or preempted PDTCH, and stops at the end of
SACCH blocks transmission.
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1601 Duration of maximum Downlink power use on busy SDCCHs
Name Q3 : downlinkPowerCtrlMaxSdcchMoy
downlinkPowerCtrlMaxSdcchMax Maximum duration
downlinkPowerCtrlMaxSdcchCum Total duration
downlinkPowerCtrlMaxSdcchEch . Number of samples
Object : bts
Function : average duration ( = total duration divided by the number of samples)
and maximum duration of maximum Downlink power use on the cell
SDCCHs for the observation period
Event : start/end of maximum SDCCH Downlink power use:
start: start timer
end:
• stop and read timer
• store its peak value
• add it to the total of maximum Downlink power use durations
on SDCCHs in the observation period
• step up by one the number of samples
Type : raw permanent
Class : L1M
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “Direct retry handover procedure”
DFD “Radio channel release DEACTIVATE SACCH ACK
procedure (normal completion)”
DFD “Connection clearing required by the BSC procedure
(communication on SIGNALING phase)”
l
1602 Duration of maximum Uplink power use on busy SDCCHs
Name Q3 : uplinkPowerCtrlMaxSdcchMoy
uplinkPowerCtrlMaxSdcchMax . . Maximum duration
uplinkPowerCtrlMaxSdcchCum . . Total duration
uplinkPowerCtrlMaxSdcchEch . . . Number of samples
Object : bts
Function : average duration ( = total duration divided by the number of samples)
and maximum duration of maximum Uplink power use on the cell
SDCCHs for the observation period
Event : start/end of maximum SDCCH Uplink power use:
start: start timer
end:
• stop and read timer
• store its peak value
l
1603/0 Connection duration of SDCCHs
Name Q3 : connectionDurationSdcchTrZoneMoy
connectionDurationSdcchTrZoneMax Maximum connection
duration
connectionDurationSdcchTrZoneCum Total connection duration
connectionDurationSdcchTrZoneEch Number of samples
Object : bts/transceiverZone
Function : average duration ( = total duration divided by the number of samples)
and maximum duration of SDCCH connections in the inner or the
outer zone of the cell, for the observation period, expressed in
multiples of 470 ms
Event : SDCCH connection/disconnection
connection: start timer
disconnection:
• stop and read timer
• store its peak value
• add it to the total of maximum SDCCH connection durations in
the observation period
• step up by one the number of samples
Type : raw permanent
Class : L1M
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
Location :
Name Q3 Location
pchAveragedQueueLengthMoy/Max/Cum/Ech CCCH--0
pchAveragedQueueLengthTs2Moy/Max/Cum/Ech CCCH--2
pchAveragedQueueLengthTs4Moy/Max/Cum/Ech CCCH--4
pchAveragedQueueLengthTs6Moy/Max/Cum/Ech CCCH--6
Precise
incrementation conditions :
l
1605 Number of paging messages queued up not transmitted
Name Q3 : pchQueuePagesDiscarded
pchQueuePagesDiscardedTs2
pchQueuePagesDiscardedTs4
pchQueuePagesDiscardedTs6
Object : bts
Location :
Name Q3 Location
pchQueuePagesDiscarded CCCH--0
pchQueuePagesDiscarded2 CCCH--2
pchQueuePagesDiscarded4 CCCH--4
pchQueuePagesDiscarded6 CCCH--6
Function : number of paging messages removed from the paging queue before
being transmitted on PCH in the observation period
Event : receipt of a paging message queuing request that leads to remove the
latest request from the queue (the maximum number of paging
messages that can be queued is reached); receipt of a
CCCH_LOAD_INDICATION message from the BTS
Type : raw permanent
Class : monitoring
Source : detected by the BTS, recorded by the BSC
Feature : Extended CCCH (TF184 - V12)
Precise
incrementation conditions :
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
CP: Com packet on PDTCH channel
No distinction is made between RACH dedicated to Circuit Call or
Packet Calls.
l
1606 Number of SDCCHs allocated in the zone (concentric cell)
Name Q3 : sdcchAllocated
sdcchAllocatedTrZone
Object : bts/transceiverZone
Function : number of SDCCH allocations in the zone
Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of SDCCH allocations for the transceiver zone
counter value that appears in the “BTS report”: number of SDCCH
allocations for the entire cell (cell = sum of the cell transceiver
zones)
For a monozone network, the zone is the entire cell
Event : allocation of an SDCCH in the zone (transceiver zone or entire cell)
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
Object : bts/transceiverZone
Class : allocation
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “Radio channel release DEACTIVATE SACCH ACK
procedure (normal completion)”
DFD “Radio channel release RELEASE INDICATION procedure
(normal completion)”
DFD “Connection clearing required by the BSC procedure
(communication on SIGNALING phase)”
DFD “SMS procedure (SMS established by the MS)”
l
1608 Number of SDCCH allocation failures in the zone (concentric
cell)
Name Q3 : sdcchRessourceFailure
sdcchRessourceFailureTrZone
Object : bts/transceiverZone
Function : number of SDCCH allocation failures due to a lack of SDCCH in the
zone
Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of SDCCH allocation failures for the transceiver zone
counter value that appears in the “BTS report”: number of SDCCH
allocation failures for the entire cell (cell = sum of the cell
transceiver zones)
For a monozone network, the zone is the entire cell
Event : SDCCH allocation refusal with cause “out of stock”
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1609/0 Number of TCH/FR or preempted PDTCH allocated for traffic
in the zone (concentric cell)
Name Q3 : tchFrAllocatedTchAllocationTrZone
tchFrAllocatedTchAllocation
Object : bts/transceiverZone
Function : number of TCH/FR or preempted PDTCH allocated in the zone for
traffic
Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of TCH/FR or preempted PDTCH allocated the
trasnceiver zone
counter value that appears in the “BTS report”: number of TCH/FR
or preempted PDTCH allocated for the entire cell (cell = sum of the
cell transceiver zones)
For a monozone network, the zone is the entire cell
Event : TCH/FR or preempted PDTCH allocation in the zone for traffic
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by CCT (Circuit
calls on TCH channel), but not by CCP (Circuit Calls on PDTCH
preempted to make a TCH channel) or CP (Com packet on PDTCH
channel).
This is because this counter is related to configured (static) TCH/FR
channel only, and does not take into account preempted PDTCH.
Data flows : Refer to Chapter 2
DFD “Immediate assignment procedure (normal completion)”
l
1609/2 Number of TCH/FR allocated because of SDCCH unavailability
in the zone (concentric cell)
Name Q3 : tchFrAllocatedOverflowAllocationTrZone
tchFrAllocatedOverflowAllocation
Object : bts/transceiverZone
Function : number of TCH/FR allocated in the zone because of SDCCH
unavailability Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of TCH/FR allocated for the transceiver zone
counter value that appears in the “BTS report”: number of TCH/FR
allocated for the entire cell (cell = sum of the cell transceiver zones)
For a monozone network, the zone is the entire cell
Event : TCH/FR allocation in the zone because of SDCCH unavailability
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
l
1609/3 Number of WPS full rate TCH allocations
Name Q3 : tchFrAllocatedWps
tchFrAllocatedWpsTrZone
Object : bts/transceiverZone
Function : Number of WPS full rate TCH (including PDTCH) allocations
Event : Allocation of a full rate TCH
Type : raw permanent
Class : allocation
Feature : WPS BSS2G and 3000 public access bandwidth protection (22465)
Source : recorded by the BSC
l
1610/0 Number of half rate TCH allocations in Transciever Zone
Name Q3 : tchHrAllocatedTchAllocation
tchHrAllocatedTchAllocationTrZone
Object : bts/transceiverZone
Function : Cumulative number of half rate TCH allocations.
Event : Allocation of a half rate TCH (including PDTCH) for a WPS call.
Type : raw permanent
Feature : WPS BSS2G and 3000 public access bandwidth protection (22465)
Source : recorded by the BSC
l
1611/0 Average number of TCH/FR or preempted PDTCH used for
traffic in the zone (concentric cell)
Name Q3 : tchFrAveragedUsedTchAllocationMoy
tchFrAveragedUsedTchAllocationEch
tchFrAveragedUsedTchAllocationCum
tchFrAveragedUsedTchAllocationMax
tchFrAveragedUsedTchAllocationTrZoneMoy
tchFrAveragedUsedTchAllocationTrZoneMax
tchFrAveragedUsedTchAllocationTrZoneCum
tchFrAveragedUsedTchAllocationTrZoneEch
Object : bts/transceiverZone
Function : average (= total number divided by number of samples) and
maximum number of TCH/FR or preempted PDTCH used for traffic
in the zone of the cell, obtained through internal sampling
Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of TCH/FR or preempted PDTCH used for traffic for the
transceiver zone
counter value that appears in the “BTS report”: number of TCH/FR
or preempted PDTCH used for traffic for the entire cell
For a monozone network, the zone is the entire cell
Event : TCH/FR or preempted PDTCH allocation/deallocation for traffic in a
zone, internal sampling time-out elapse:
allocation: step up by one the instantaneous value of the number of
TCH/FR or preempted PDTCH used for traffic in the zone
deallocation: step down by one the instantaneous value of the
number of TCH/FR or preempted PDTCH used for traffic in the
zone
sampling time-out elapse:
• read the instantaneous value of the number of TCH/FR or
preempted PDTCH used for traffic in the zone
• store its peak value
• add it to the total number of TCH/FR or preempted PDTCH
allocations for traffic in the zone for the observation period
• step up by one the number of samples
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
When new counter 1824 is received, its value is copied in counter
1611.
Data flows : Refer to Chapter 2
DFD “GPRS procedure (no resource available for a PDTCH
preemption)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on TRAFFIC phase)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
DFD “Connection clearing required by the BSC procedure
(communication on TRAFFIC phase)”
l
1611/1 Average number of TCH/FR used for call reestablishments in the
zone (concentric cell) (primo-allocation)
Name Q3 : tchFrAveragedUsedPrimoAllocationMoy
tchFrAveragedUsedPrimoAllocationMax
tchFrAveragedUsedPrimoAllocationCum
tchFrAveragedUsedPrimoAllocationEch
tchFrAveragedUsedPrimoAllocationTrZoneMoy
tchFrAveragedUsedPrimoAllocationTrZoneMax
tchFrAveragedUsedPrimoAllocationTrZoneCum
tchFrAveragedUsedPrimoAllocationTrZoneEch
Object : bts/transceiverZone
Function : average (= total number divided by number of samples) and
maximum number of TCH/FR used for call reestablishments in the
zone, obtained through internal sampling
Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of TCH/FR used for call reestablisment for the transceiver
zone
counter value that appears in the “BTS report”: number of TCH/FR
used for call reestablishment for the entire cell
For a monozone network, the zone is the entire cell
Event : TCH/FR allocation/deallocation for call reestablishment in a zone,
internal sampling time-out elapse:
allocation: step up by one the instantaneous value of the number of
TCH/FR used for call reestablishment in the zone
deallocation: step down by one the instantaneous value of the
number of TCH/FR used for call reestablishment in the zone
sampling time-out elapse:
• read the instantaneous value of the number of TCH/FR used for
call reestablishment in the zone
• store its peak value
• add it to the total number of TCH/FR allocations for call
reestablishment in the zone for the observation period
• step up by one the number of samples
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by CCT (Circuit
calls on TCH channel), but not by CCP (Circuit Calls on PDTCH
preempted to make a TCH channel) or CP (Com packet on PDTCH
channel).
This is because this counter is related to configured (static) TCH/FR
channel only, and does not take into account preempted PDTCH.
Data flows : Refer to Chapter 2
DFD “Immediate assignment procedure (normal completion)”
l
1611/2 Average number of TCH/FR used because of SDCCH
unavailability in the zone (concentric cell)
Name Q3 : tchFrAveragedUsedOverflowAllocationMoy
tchFrAveragedUsedOverflowAllocationMax
tchFrAveragedUsedOverflowAllocationCum
tchFrAveragedUsedOverflowAllocationEch
tchFrAveragedUsedOverflowAllocationTrZoneMoy
tchFrAveragedUsedOverflowAllocationTrZoneMax
tchFrAveragedUsedOverflowAllocationTrZoneCum
tchFrAveragedUsedOverflowAllocationTrZoneEch
Object : bts/transceiverZone
Function : average (= total number divided by number of samples) and
maximum number of TCH/FR used because of SDCCH
unavailability in the zone, obtained through internal sampling
Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of TCH/FR used because of SDCCH unavailability the
transceiver zone
counter value that appears in the “BTS report”: number of
TCH/FR because of SDCCH unavailabillity for the entire cell
For a monozone network, the zone is the entire cell
l
1611/3 Average and maximum number of WPS full rate TCH allocations
Name Q3 : tchFrAveragedUsedWpsCum
tchFrAveragedUsedWpsEch
tchFrAveragedUsedWpsMax
tchFrAveragedUsedWpsMoy
tchFrAveragedUsedWpsTrZoneCum
tchFrAveragedUsedWpsTrZoneEch
tchFrAveragedUsedWpsTrZoneMax
tchFrAveragedUsedWpsTrZoneMoy
Object : bts/transceiverZone
Function : Average and maximum number of WPS full rate TCH (including
PDTCH) allocations
Event : Allocation/de--allocation of a full rate TCH
Type : raw permanent
Class : allocation
Feature : WPS BSS2G and 3000 public access bandwidth protection (22465)
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by CCT (Circuit
calls on TCH channel), but not by CCP (Circuit Calls on PDTCH
preempted to make a TCH channel).
This is because this counter is related to configured (static) TCH/FR
channel. This counter is pegged on the traffic channel allocation for a
WPS call if the WPS Management flag is enabled. This counter is
pegged on the traffic channel de--allocation for a call inititiated as a
WPS call.
l
1612/0 Average and maximum number of half rate TCH allocations
Name Q3 : tchHrAveragedUsedTchAllocationCum
tchHrAveragedUsedTchAllocationEch
tchHrAveragedUsedTchAllocationMax
tchHrAveragedUsedTchAllocationMoy
tchHrAveragedUsedTchAllocationTrZoneCum
tchHrAveragedUsedTchAllocationTrZoneEch
tchHrAveragedUsedTchAllocationTrZoneMax
tchHrAveragedUsedTchAllocationTrZoneMoy
Object : bts/transceiverZone
Function : Average and maximum number of half rate TCH (including PDTCH)
allocations
Class : allocation
l
1613 Number of TCH/FR and preemptable PDTCH allocation failures
in the zone (concentric cell)
Name Q3 : tchFrRessourceFailure
tchFrRessourceFailureTrZone
Object : bts/transceiverZone
Function : number of allocation failures due to a lack of TCH/FR and
preemptable PDTCH in the zone, and due to a lack of free entries in
the queue
Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of TCH/FR and preemptable PDTCH allocation failures
for the transceiver zone
counter value that appears in the “BTS report”: number of TCH/FR
and preemptable PDTCH allocation failures for the entire cell
For a monozone network, the zone is the entire cell
Event : TCH/FR and preemptable PDTCH allocation refusal in the zone with
cause “out of stock”
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Note : This counter is also incremented if there are free TCHs, that are
reserved for allocation requests with the maximum priority
(allocPriorityThreshold attribute).
Also see C1039 counter for summation count at bts level.
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure (no available resource for a PDTCH
preemption)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (no resource
available and queuing not activated)”
l
1614 Number of TCH/HR and preemptable PDTCH allocation
failures in the zone (concentric cell)
Name Q3 : tchHrRessourceFailure
tchHrRessourceFailureTrZone
Object : bts/transceiverZone
Function : number of failures caused by the lack of half rate TCH in a tdma_class
of the cell and a lack of free entries in the queue.
Event : Immediate refusal of allocation or refusal of queuing a TCH request.
Type : totalization
Class : TDMA
Source : recorded by the BSC
Note : The object identifier is used to set a mdCounterIdArray field.
l
1616/0 Average number of TCHs with highest priority queued up
Name Q3 : tchAveragedQueueLengthHighPriorityMoy
tchAveragedQueueLengthHighPriorityMax
tchAveragedQueueLengthHighPriorityCum
tchAveragedQueueLengthHighPriorityEch
Object : bts
Function : average (= total number divided by number of samples) and
maximum number of TCH allocation requests with maximum
priority queued for the cell, obtained through internal sampling
Event : TCH allocation request queued with cause “out of stock”, TCH
allocation, internal sampling time-out elapse:
queuing: step up by one the instantaneous value of the number of
TCHs with maximum priority queued
allocation: step down by one the instantaneous value of the number
of TCHs with maximum priority queued
sampling time-out elapse:
• read the instantaneous value of the number of TCHs with
maximum priority queued
• store its peak value
• add it to the total number of TCH allocation requests with
maximum priority queued for the observation period
• step up by one the number of samples
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “queuing of the assignment procedure (normal completion)”
DFD “Direct retry handover procedure”
l
1616/1 Average number of TCHs without highest priority queued up
Name Q3 : tchAveragedQueueLengthOtherPriorityMoy
tchAveragedQueueLengthOtherPriorityMax
tchAveragedQueueLengthOtherPriorityCum
tchAveragedQueueLengthOtherPriorityEch
Object : bts
Function : average (= total number divided by number of samples) and
maximum number of TCH allocation requests with non-maximum
priority queued for the cell, obtained through internal sampling
Event : TCH allocation request queued with cause “out of stock”, TCH
allocation, internal sampling time-out elapse:
queuing: step up by one the instantaneous value of the number of
TCHs with non-maximum priority queued
allocation: step down by one the instantaneous value of the number
of TCHs with non-maximum priority queued
sampling time-out elapse:
• read the instantaneous value of the number of TCHs with
non-maximum priority queued
• store its peak value
• add it to the total number of TCH allocation requests with
non-maximum priority queued for the observation period
• step up by one the number of samples
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “queuing of the assignment procedure (normal completion)”
DFD “Direct retry handover procedure”
l
1617/0 Number of TCH allocation requests with highest priority queued
up unsatisfied
Name Q3 : tchQueuingExpirationHighPriority
Object : bts
Function : number of TCH allocation requests with maximum priority queued
and unsatisfied because of time-out elapse
Event : time-out elapse of a TCH allocation request with maximum priority
queued
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1617/1 Number of TCH allocation requests without highest priority
queued up unsatisfied
Name Q3 : tchQueuingExpirationOtherPriority
Object : bts
Function : number of TCH allocation requests with non-maximum priority
queued and unsatisfied because of time-out elapse
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “queuing of the assignment procedure (normal completion)”
DFD “Direct retry handover procedure”
l
1618/1 Average waiting time of TCH allocation requests without highest
priority
Name Q3 : tchQueuingDurationOtherPriorityMoy
tchQueuingDurationOtherPriorityMax . . . . . . Max wait durations
tchQueuingDurationOtherPriorityCum . . . . . . Total wait durations
tchQueuingDurationOtherPriorityEch . . . . . . . Number of samples
Object : bts
Function : average waiting duration ( = total duration divided by the number of
samples) and maximum waiting duration of TCH allocation requests
with non-maximum priority in the cell, obtained through internal
sampling. Counts both requests which are served, aborted or extracted
on timer expiration
Event : TCH allocation request with non-maximum priority queued,
allocated, removed from the queue, sampling time-out elapse:
queuing: start timer
allocation/removal: stop timer
sampling time-out elapse:
• read timer
• store its peak value
• add it to the total of waiting durations of TCH allocation
requests with non-maximum priority in the observation period
• step up by one the number of samples
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “queuing of the assignment procedure (normal completion)”
DFD “Direct retry handover procedure”
l
1619/0 Average number of free channels in interference band No.0
Name Q3 : channelAveragedIdlePerInterfBand0Moy
channelAveragedIdlePerInterfBand0Max . . . . Max in Band No.0
channelAveragedIdlePerInterfBand0Cum . . . . Total in Band No.0
channelAveragedIdlePerInterfBand0Ech . . . . . Number of samples
Object : bts
Function : average (= total number divided by number of samples) and
maximum number of radio idle channels in Interference band No.0,
obtained through internal sampling
Event : SDCCH or TCH allocation/deallocation, sampling time-out elapse
Type : raw permanent
Class : interference
Source : recorded by the BSC
Precise
incrementation conditions :
Measurement of interference is performed when in Idle mode. Before
the preemption, the PDTCH is assigned to the PCU and thus
considered as used from the BSS side. During the preemption, the
PDTCH is re--configured as TCH/FR and then assigned to a Circuit
Call. As a result, measurement of interferences involves configured
(static) TCH/FR only.
Note : In case of concentric cells (2 TDMAs in one cell):
The maximum value is the maximum number of radio channels in
the interference band of the TDMA which supports the greater
number of channels.
The cumulative value, which is relative to one TDMA, is therefore
the sum of numbers of radio channels in the interference band
divided by the number of TDMAs in the cell (i.e. 2).
l
1619/1 Average number of free channels in interference band No.1
Name Q3 : channelAveragedIdlePerInterfBand1Moy
channelAveragedIdlePerInterfBand1Max . . . . Max in Band No.1
channelAveragedIdlePerInterfBand1Cum . . . . Total in Band No.1
channelAveragedIdlePerInterfBand1Ech . . . . . Number of samples
Object : bts
Function : average (= total number divided by number of samples) and
maximum number of radio idle channels in Interference band No.1,
obtained through internal sampling
Event : SDCCH or TCH allocation/deallocation, sampling time-out elapse
Type : raw permanent
Class : interference
Source : recorded by the BSC
Precise
incrementation conditions :
Measurement of interference is performed when in Idle mode. Before
the preemption, the PDTCH is assigned to the PCU and thus
considered as used from the BSS side. During the preemption, the
PDTCH is re--configured as TCH/FR and then assigned to a Circuit
Call. As a result, measurement of interferences involves configured
(static) TCH/FR only.
Note : In case of concentric cells (2 TDMAs in one cell):
The maximum value is the maximum number of radio channels in
the interference band of the TDMA which supports the greater
number of channels.
The cumulative value, which is relative to one TDMA, is therefore
the sum of numbers of radio channels in the interference band
divided by the number of TDMAs in the cell (i.e. 2).
l
1619/2 Average number of free channels in interference band No.2
Name Q3 : channelAveragedIdlePerInterfBand2Moy
channelAveragedIdlePerInterfBand2Max . . . . Max in Band No.2
channelAveragedIdlePerInterfBand2Cum . . . . Total in Band No.2
channelAveragedIdlePerInterfBand2Ech . . . . . Number of samples
Object : bts
Function : average (= total number divided by number of samples) and
maximum number of radio idle channels in Interference band No.2,
obtained through internal sampling
Precise
incrementation conditions :
Measurement of interference is performed when in Idle mode. Before
the preemption, the PDTCH is assigned to the PCU and thus
considered as used from the BSS side. During the preemption, the
PDTCH is re--configured as TCH/FR and then assigned to a Circuit
Call. As a result, measurement of interferences involves configured
(static) TCH/FR only.
Class : interference
Source : recorded by the BSC
Precise
incrementation conditions :
Measurement of interference is performed when in Idle mode. Before
the preemption, the PDTCH is assigned to the PCU and thus
considered as used from the BSS side. During the preemption, the
PDTCH is re--configured as TCH/FR and then assigned to a Circuit
Call. As a result, measurement of interferences involves configured
(static) TCH/FR only.
Note : In case of concentric cells (2 TDMAs in one cell):
The maximum value is the maximum number of radio channels in
the interference band of the TDMA which supports the greater
number of channels.
The cumulative value, which is relative to one TDMA, is therefore
the sum of numbers of radio channels in the interference band
divided by the number of TDMAs in the cell (i.e. 2).
l
1619/4 Average number of free channels in interference band No.4
Name Q3 : channelAveragedIdlePerInterfBand4Moy
channelAveragedIdlePerInterfBand4Max . . . . Max in Band No.4
channelAveragedIdlePerInterfBand4Cum . . . . Total in Band No.4
channelAveragedIdlePerInterfBand4Ech . . . . . Number of samples
Object : bts
Function : average (= total number divided by number of samples) and
maximum number of radio idle channels in Interference band No.4,
obtained through internal sampling
Event : SDCCH or TCH allocation/deallocation, sampling time-out elapse
Type : raw permanent
Class : interference
Source : recorded by the BSC
Precise
incrementation conditions :
Measurement of interference is performed when in Idle mode. Before
the preemption, the PDTCH is assigned to the PCU and thus
considered as used from the BSS side. During the preemption, the
PDTCH is re--configured as TCH/FR and then assigned to a Circuit
Call. As a result, measurement of interferences involves configured
(static) TCH/FR only.
Note : In case of concentric cells (2 TDMAs in one cell):
The maximum value is the maximum number of radio channels in
the interference band of the TDMA which supports the greater
number of channels.
The cumulative value, which is relative to one TDMA, is therefore
the sum of numbers of radio channels in the interference band
divided by the number of TDMAs in the cell (i.e. 2).
l
1620 Number of unsuccessful “directed retry” handovers because the
list of eligible cells is empty
Name Q3 : directedRetryUnsuccessNoBts
Object : bts
Function : number of unsuccessful directed retry handovers because the list of
eligible cells is empty
Event : no reception of HANDOVER INDICATION with cause “directed
retry” after receipt of CONNECTION STATE RESPONSE from the
BTS (with an empty list of eligible cells and in the directed retry
handover procedure) and before the end of queuing phase
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1621 Number of SAPI 3 session establishments for SMS
Name Q3 : sapi3SessionEstablishment
Object : bts
Function : number of SAPI sessions established to satisfy a short message
broadcast request in the cell
Event : receipt of one of the following messages from the BTS:
ESTABLISH INDICATION on SAPI3 (establishment requested
by a mobile)
ESTABLISH CONFIRM on transmission of ESTABLISH
REQUEST with SAPI3 value (receipt of a DTAP message on
SAPI3 from the MSC when no SAPI3 session is in-progress)
Type : raw permanent
Class : SMS service
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “SMS procedure (SMS established by the MS)”
DFD “SMS procedure (SMS established by the MSC)”
l
1622 Number of MS measurement messages not received
Name Q3 : msLostMeasurements
msLostMeasurementsTrZone
Object : bts/transceiverZone
Function : number of mobile measurement messages not received by the inner or
the outer zone of the cell
Event : BSC receipt of STOP MEASUREMENT ACK with no measurement
message from a mobile
Type : raw permanent
Class : L1M
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
DFD “Radio channel release DEACTIVATE SACCH ACK
procedure (normal completion)”
DFD “Radio channel release RELEASE INDICATION procedure
(normal completion)”
DFD “Connection clearing required by the BSC procedure
(communication on TRAFFIC phase)”
DFD “Connection clearing required by the BSC procedure
(communication on SIGNALING phase)”
Object : bts/transceiverZone
Class : L1M
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1624 Sum of Uplink signal strength measurements
Name Q3 : rxLevUpLink
Object : bts/transceiverZone
Function : sum of the uplink signal strength measurements performed by the
BTS on the cell in the observation period, expressed in GSM values
[0 to 63]
Event : BSC receipt of STOP MEASUREMENT ACK from the BTS
Type : raw permanent
Class : L1M
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
DFD “Radio channel release DEACTIVATE SACCH ACK
procedure (normal completion)”
DFD “Radio channel release RELEASE INDICATION procedure
(normal completion)”
DFD “Connection clearing required by the BSC procedure
(communication on TRAFFIC phase)”
DFD “Connection clearing required by the BSC procedure
(communication on SIGNALLING phase)”
l
1626 Sum of Uplink signal quality measurements
Name Q3 : rxQualUpLinkTrZone
Object : transceiverZone
Function : sum of the uplink signal quality measurements performed by the BTS
on the inner or the outer zone of the cell in the observation period,
expressed in 100xBER
l
1629/0 Number of Full-Rate channels activated for signaling
Name Q3 : channelActivateSignallingFullRate
Object : bts
Function : number of full-rate channels (SDCCH or TCH/FR) activated for
signaling in the cell
Event : transmission of CHANNEL ACTIVATE with CHANNEL
MODE = “signalling”
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Oritinating Calls)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1629/1 Number of Half-Rate channels activated for signaling
Name Q3 : channelActivateSignallingHalfRate
Object : bts
Function : number of half-rate channels (TCH/HR) activated for signaling in the
cell
Event : transmission of CHANNEL ACTIVATE with CHANNEL
MODE = “signalling”
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Oritinating Calls)”
DFD “Immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
DFD “SMS procedure (SMS established by the MS)”
l
1700 Average number of TCH/FR and preemptable PDTCH available
in multizone cell
Name Q3 : tchFrAveragedAvailable
tchFrAveragedAvailableMoy
tchFrAveragedAvailableMax
tchFrAveragedAvailableCum
tchFrAveragedAvailableEch
tchFrAveragedAvailableTrZoneMoy
tchFrAveragedAvailableTrZoneMax Max TCH/FR available
tchFrAveragedAvailableTrZoneCumTotal TCH/FR available
tchFrAveragedAvailableTrZoneEch Number of samples
Object : bts/transceiverZone
Function : average (= total number divided by number of samples) and
maximum number of available radio TS for circuit calls, on a TDMA
class basis. Used resources are:
radio TS used for circuit call only
radio TS shared between circuit services and packet data services
Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of TCH/FR and preemptable PDTCH available for the
transceiver zone
counter value that appears in the “BTS report”: number of TCH/FR
and preemptable PDTCH available for the entire cell
For a monozone network, the zone is the entire cell
Formula : due to the minNbrGprsTS parameter defined on a cell basis, the exact
implementation of this counter is as follows:
Outer zone:
if the number of PDTCH in the cell is less than minNbrGprsTS, then
C1700_oz = Number_of_TCH_oz + Number_of_PDTCH_oz –
Number_of_PDTCH_cell
else
C1700_oz = Number_of_TCH_oz + Number_of_PDTCH_oz –
minNbrGprsTS
Inner zone:
C1700_iz = Number_of_TCH_iz + Number_of_PDTCH_iz
Where oz = outer zone and iz = inner zone
l
1701 Average number of SDCCH available in the zone (concentric cell)
Name Q3 : sdcchAveragedAvailableMoy
sdcchAveragedAvailableMax . . . . . Max available SDCCHs
sdcchAveragedAvailableCum . . . . Total available SDCCHs
sdcchAveragedAvailableEch . . . . . Number of samples
sdcchAveragedAvailableTrZoneMoy
sdcchAveragedAvailableTrZoneMax . . . . Max SDCCH available
sdcchAveragedAvailableTrZoneCum . . . Total SDCCH available
sdcchAveragedAvailableTrZoneEch . . . . Number of samples
Object : bts/transceiverZone
Function : average (= total number divided by number of samples) and
maximum number of available SDCCHs -- allocated or available
obtained by internal sampling
Counter value calculation:
counter value that appears in the “Transceiver zone report”:
number of SDCCH averaged available for the transceiver zone
counter value that appears in the “BTS report”: number of SDCCH
averaged available for the entire cell (cell = sum of the cell
transceiver zones)
For a monozone network, the zone is the entire cell
Event : SDCCH allocation/deallocation in the zone (transceiver zone or
entire cell), radio channel blocking, SYS INFO 5 and 6
acknowledgement not received, internal sampling time-out elapse:
allocation: step up by one the instantaneous value of the number of
available SDCCHs in the zone (transceiver zone or entire cell)
deallocation/blocking/non-acknowledgement: step down by one
the instantaneous value of the number of available SDCCHs in the
zone (transceiver zone or entire cell)
sampling time-out elapse:
• read the instantaneous value of the number of available
SDCCHs in the zone
• store its peak value
• add it to the total number of available SDCCHs in the zone for
the observation period
• step up by one the number of samples
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1702 Number of channel allocation requests for mobiles over 35 km
(extended mode)
Name Q3 : channelRequestExtended
Object : bts
Function : number of channel allocation requests in the cell because of timing
advance greater than 63
Event : receipt of CHANNEL REQUEST containing a timing advance value
greater than 63
Type : raw permanent
Class : setup
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
l
1705/0 Number of TCH/FR activation for transparent data service with
a 1200/75 b/s transmission rate
Name Q3 : channelActivateTchFrDataT16
Object : bts
Function : number of full–rate channels activated for transparent data service
messages in the cell with a 1200/75 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a transparent service on a full--rate
TCH with a 1200/75 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1705/1 Number of TCH/FR activation for transparent data service with
a 600 b/s transmission rate
Name Q3 : channelActivateTchFrDataT600
Object : bts
Function : number of full–rate channels activated for transparent data service
messages in the cell with a 600 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a transparent service on a full--rate
TCH with a 600 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1705/2 Number of TCH/FR activation for transparent data service with
a 1200 b/s transmission rate
Name Q3 : channelActivateTchFrDataT1200
Object : bts
Function : number of full–rate channels activated for transparent data service
messages in the cell with a 1200 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a transparent service on a full--rate
TCH with a 1200 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1705/3 Number of TCH/FR activation for transparent data service with
a 2400 b/s transmission rate
Name Q3 : channelActivateTchFrDataT2400
Object : bts
Function : number of full–rate channels activated for transparent data service
messages in the cell with a 2400 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a transparent service on a full--rate
TCH with a 2400 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1705/4 Number of TCH/FR activation for transparent data service with
a 4800 b/s transmission rate
Name Q3 : channelActivateTchFrDataT4800
Object : bts
Function : number of full–rate channels activated for transparent data service
messages in the cell with a 4800 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a transparent service on a full--rate
TCH with a 4800 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1705/5 Number of TCH/FR activation for transparent data service with
a 9600 b/s transmission rate
Name Q3 : channelActivateTchFrDataT9600
Object : bts
Function : number of full–rate channels activated for transparent data service
messages in the cell with a 9600 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a transparent service on a full--rate
TCH with a 9600 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1705/6 Number of TCH/FR activation for transparent data service with
a 14400 b/s transmission rate
Name Q3 : channelActivateTchFrDataT14400
Object : bts
Function : number of full–rate channels activated for transparent data service
messages in the cell with a 14400 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a transparent service on a full--rate
TCH with a 14400 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1706/0 Number of channel activation for transparent data service on
half rate TCH
Name Q3 : channelActivateTchHrDataT16
Object : bts
Function : Number of channel activation for transparent data service on half rate
TCH.
Event : transmission of a CHANNEL_ACTIVATE message or of a
MODE_MODIFY message with a CHANNEL MODE record set to
“data” for a transparent service on a half rate TCH.
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1706/1 Number of channel activation for transparent data service on
half rate TCH with a 600 b/s transmission rate.
Name Q3 : channelActivateTchHrDataT600
Object : bts
Function : Number of channel activation for transparent data service on half rate
TCH with a 600 b/s transmission rate.
Event : transmission of a CHANNEL_ACTIVATE message or of a
MODE_MODIFY message with a CHANNEL MODE record set to
“data” for a transparent service on a half rate TCH.
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1706/2 Number of channel activation for transparent data service on
half rate TCH with a 1200 b/s transmission rate.
Name Q3 : channelActivateTchHrDataT1200
Object : bts
Function : Number of channel activation for transparent data service on half rate
TCH with a 1200 b/s transmission rate.
Event : transmission of a CHANNEL_ACTIVATE message or of a
MODE_MODIFY message with a CHANNEL MODE record set to
“data” for a transparent service on a half rate TCH.
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1706/3 Number of channel activation for transparent data service on
half rate TCH with a 2400 b/s transmission rate
Name Q3 : channelActivateTchHrDataT2400
Object : bts
Function : Number of channel activation for transparent data service on half rate
TCH with a 2400 b/s transmission rate.
Event : transmission of a CHANNEL_ACTIVATE message or of a
MODE_MODIFY message with a CHANNEL MODE record set to
“data” for a transparent service on a half rate TCH.
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1706/4 Number of channel activation for transparent data service on
half rate TCH with a 4800 b/s transmission rate
Name Q3 : channelActivateTchHrDataT4800
Object : bts
Function : Number of channel activation for transparent data service on half rate
TCH with a 4800 b/s transmission rate.
Event : transmission of a CHANNEL_ACTIVATE message or of a
MODE_MODIFY message with a CHANNEL MODE record set to
“data” for a transparent service on a half rate TCH.
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “immediate assignment procedure (normal completion)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1707/0 Number of TCH/FR activation for non--transparent data service
with a 6000 b/s transmission rate
Name Q3 : channelActivateTchFrDataNT6000
Object : bts
Function : number of full–rate channels activated for non--transparent data
service messages in the cell with a 6000 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a non--transparent service on a
full--rate TCH with a 6000 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1707/1 Number of TCH/FR activation for non--transparent data service
with a 12000 b/s transmission rate
Name Q3 : channelActivateTchFrDataNT12000
Object : bts
Function : number of full–rate channels activated for non--transparent data
service messages in the cell with a 12000 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a non--transparent service on a
full--rate TCH with a 12000 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1707/2 Number of TCH/FR activation for non--transparent data service
with a 14500 b/s transmission rate
Name Q3 : channelActivateTchFrDataNT14500
Object : bts
Function : number of full–rate channels activated for non--transparent data
service messages in the cell with a 14500 b/s transmission rate
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a non--transparent service on a
full--rate TCH with a 14500 b/s transmission rate
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR and preempted
PDTCH channels (circuit calls).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1708/0 Number of channel activation for non transparent data service on
half rate TCH.
Name Q3 : channelActivateTchHrDataNT6000
Object : bts
Function : Cumulative number of channel activation for non transparent data
service on half rate TCH.
Event : Transmission of a CHANNEL_ACTIVATE message or of a
MODE_MODIFY message with a
CHANNEL MODE record set to data for a non transparent
service on a half rate TCH.
Type : CUM
Source : TBD
l
1709 Number of TCH/FR activation for transparent data service
Name Q3 : channelActTchFrDataT
Object : bts
Function : number of full–rate channels activated for transparent data service
messages in the cell
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a transparent service on a full--rate
TCH
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1710 Number of TCH/FR activation for non--transparent data service
Name Q3 : channelActTchFrDataNT
Object : bts
Function : number of full–rate channels activated for non--transparent data
service messages in the cell
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for a non--transparent service on a
full--rate TCH
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Direct retry handover procedure”
l
1711/0 Number of TCH/HR activation for transparent data service
Name Q3 : channelActTchHrDataT
Object : bts
Function : number of half–rate channels activated for transparent data service
messages in the cell
Event : transmission of CHANNEL ACTIVATE or MODE MODIFY with
CHANNEL MODE = “data” for atransparent service on a full--rate
TCH
Type : raw permanent
Class : assignment
Source : recorded by the BSC
l
1714 Duration of the overload situation
Name Q3 : btsOverloadDurationMoy
btsOverloadDurationMax
btsOverloadDurationCum
btsOverloadDurationEch
Object : bts
Function : duration of the overload situation: the number of free TCHs in the cell
is lower than the minimum threshold, or the number of queued TCH
requests is greater than the threshold.
Note that the number of free TCHs does not take preemptable PDTCH
into account.
Event : allocation/de--allocation of a TCH, queueing of a TCH request,
liberation of a queued TCH request, block/unblock of a TCH, or
TDMA attribution/removal
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Feature : Handover for traffic reasons (TF132 - V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
But it is not concerned by CCP (Circuit Calls on PDTCH preempted
to make a TCH channel) or CP calls (Com packet on PDTCH
channel).
l
1715 Number of attempts of assignation of a TCH/FR or a preempted
PDTCH for dualband mobiles
Name Q3 : attemptedTchFrSeizuresMsDualb
Object : bts
Function : number of attempts of assignation of a TCH/FR or a preempted
PDTCH for dualband mobiles
Event : transmission of ASSIGNMENT COMMAND to the mobile
Type : raw permanent
Class : assignment
Source : recorded by the BSC
l
1721/0 Number of erroneous frames
Name Q3 : ecuActivation
Object : bts
Function : number of erroneous frames
l
1722/0 Number of VBS (Voice Broadcast Service) call initiations
Name Q3 : asciCallInitiationVbs
Object : bts
Function : number of VBS (Voice Broadcast Service) call initiations
Event : receipt of a CM SERVICE REQUEST, IMMEDIATE_SETUP,
IMMEDIATE_SETUP2 or HO_REQUEST message
Type : raw permanent
Class : asci
Source : recorded by the BSC
Feature : GSM--R
Precise
incrementation conditions :
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
l
1722/1 Number of VGCS (Voice Group Call Service) call initiations
Name Q3 : asciCallInitiationVgcs
Object : bts
Function : number of VGCS (Voice Group Call Service) call initiations
Event : receipt of a CM SERVICE REQUEST, IMMEDIATE_SETUP,
IMMEDIATE_SETUP2, or HO_REQUEST message
Type : raw permanent
Class : asci
Source : recorded by the BSC
Feature : GSM--R
Precise
incrementation conditions :
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
l
1723 Number of inband pagings taken into account
Name Q3 : asciInbandPaging
Object : bts
Function : number of inband pagings taken into account
Event : receipt of a PAGING message if:
eMLPP present
eMLPP precedence > O&M threshold
VBS call in progress
Type : raw permanent
Class : asci
Source : recorded by the BSC
Feature : GSM--R
Precise
incrementation conditions :
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
Note : If several calls are in progress, only one counter update is performed.
l
1724 Number of inband notifications taken into account
Name Q3 : asciInbandNotification
Object : bts
Function : number of inband notifications taken into account
Event : receipt of a VBS_ASSIGNMENT_REQUEST message if:
eMLPP present
eMLPP precedence > O&M threshold
call in progress
Type : raw permanent
Class : asci
Source : recorded by the BSC
Feature : GSM--R
Precise
incrementation conditions :
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
Note : If several calls are in progress, only one counter update is performed.
l
1725 Number of preemptions performed on a call in progress in the cell
Name Q3 : asciPreemptionPerformed
Object : bts
Function : number of preemptions performed on a call in progress in the cell
Event : preemption of a call (i.e. conditions on GSM priority satisfied)
Type : raw permanent
Class : asci
Source : recorded by the BSC
Feature : GSM--R
Precise
incrementation conditions :
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
l
1726/0 Number of fallbacks from a required data rate to another data
rate with cause lack of resources
Name Q3 : dataNtRateFbTchResLack
Object : bts
Function : number of fallbacks from a required data rate to another data rate with
cause lack of resources
Event : configuration mismatch or response from radio allocator
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1726/1 Number of fallbacks from a required data rate to another data
rate with cause configuration not allowed
Name Q3 : dataNtRateFbTchConfNotAllowed
Object : bts
Function : number of fallbacks from a required data rate to another data rate with
cause configuration not allowed
Event : configuration mismatch or response from radio allocator
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1730 Number of signaling channels allocated for replies to paging
Name Q3 : pagingResponse
Object : bts
Function : number of signaling channel allocation requests for “reply to paging
request” in the cell (cause = xx001 or xx100)
Event : receipt of CHANNEL REQUEST with cause “reply to paging
request”
Type : raw permanent
Class : establishment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “immediate assignment procedure (normal completion)”
DFD “Immediate assignment paging procedure (normal
completion)”
l
1744 Number of TCH/FR or preempted PDTCH allocated in the cell
Name Q3 : tchFrAllocated
Object : bts/transceiverZone
Function : number of TCH/FR or preempted PDTCH allocated in the cell
Event : TCH/FR or preempted PDTCH allocation in the cell
Type : raw permanent
Class : allocation
Source : recorded by the BSC
l
1746 Average number of TCH/FR or preempted PDTCH used in the
concentric cell and zone
Name Q3 : tchFrAveragedUsedMoy
tchFrAveragedUsedMax
tchFrAveragedUsedCum
tchFrAveragedUsedEch
tchFrAveragedUsedTrZoneMax
tchFrAveragedUsedTrZoneMoy
tchFrAveragedUsedTrZoneCum
tchFrAveragedUsedTrZoneEch
Object : bts/transceiverZone
Function : average (= total number divided by number of samples) and
maximum number of TCH/FR or preempted PDTCH used in the inner
or outer zone of the cell, obtained through internal sampling.
Event : TCH/FR or preempted PDTCH allocation/deallocation:
allocation: step up by one the instantaneous value of the number of
TCH/FR or preempted PDTCH used in the cell or zone.
deallocation: step down by one the instantaneous value of the
number of TCH/FR or preempted PDTCH used in the cell or zone.
Type : raw permanent
Class : allocation
Source : recorded by the BSC
Precise
incrementation conditions :
When new counter 1826 is received, its value is copied in counter
1746.
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (no available resource for a PDTCH
preemption)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “dedicated channel assignment procedure (normal
completion)”
DFD “queuing of the assignment procedure (normal completion)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1756/0 Number of refusals to accept an intra--cell handover in the cell on
TCH with cause lack of radio resources
Name Q3 : hoFailureIntraBtsTchRadioLack
Object : bts
Object : number of refusals to accept an intra--cell handover on TCH in the cell
with cause lack of radio resources
Event : lack of radio resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1756/1 Number of refusals to accept an intra--cell handover on TCH in
the cell with cause receipt from the BTS of a CHANNEL ACTI-
VATE NACK message
Name Q3 : hoFailureIntraBtsTchChannelActivateNack
Object : bts
Function : number of refusals to accept an intra--cell handover on TCH in the cell
with cause receipt from the BTS of CHANNEL ACTIVATE NACK
message
Event : receipt from the BTS of a CHANNEL ACTIVATE NACK message
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1756/2 Number of refusals to accept an intra--cell handover on TCH in
the cell with cause expiration of TchnAck timer
Name Q3 : hoFailureIntraBtsTchTchnAckTimerExp
Object : bts
Function : number of refusals to accept an intra--cell handover on TCH in the cell
with cause expiration of TchnAck timer
Event : expiration of TchnAck timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1757/0 Number of refusals to accept an intra--cell handover in the cell on
SDCCH with cause lack of radio resources
Name Q3 : hoFailureIntraBtsSdcchRadioLack
Object : bts
Function : number of refusals to accept an intra--cell handover on SDCCH in the
cell with cause lack of radio resources
Event : lack of radio resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1757/1 Number of refusals to accept an intra--cell handover on SDCCH
in the cell with cause receipt from the BTS of a CHANNEL
ACTIVATE NACK message
Name Q3 : hoFailureIntraBtsSdcchChannelActivateNack
Object : bts
Function : number of refusals to accept an intra--cell handover on SDCCH in the
cell with cause receipt from the BTS of CHANNEL ACTIVATE
NACK message
Event : receipt from the BTS of a CHANNEL ACTIVATE NACK message
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1757/2 Number of refusals to accept an intra--cell handover on TCH in
the cell with cause expiration of TchnAck timer
Name Q3 : hoFailureIntraBtsSdcchTchnAckTimerExp
Object : bts
Function : number of refusals to accept an intra--cell handover on SDCCH in the
cell with cause expiration of TchnAck timer
Event : expiration of TchnAck timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1758/0 Number of incoming intra BSS handover requests, on TCH with
cause lack of radio resources, which have been refused
Name Q3 : hoFailureIncomingIntraBssTchRadioLack
Object : bts
Function : number of incoming intra BSS handover requests, on TCH with cause
lack of radio resources, which have been refused
Event : lack of radio resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1758/1 Number of incoming intra BSS handover requests, on TCH with
cause incoming handover not allowed in the cell, which have been
refused
Name Q3 : hoFailureIncomingIntraBssTchHoNotAllowed
Object : bts
Function : number of incoming intra BSS handover requests, on TCH with cause
incoming handover not allowed in the cell, which have been refused
Event : incoming handover not allowed in the cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1758/2 Number of incoming intra BSS handover requests, on TCH with
cause receipt from the BTS of a CHANNEL ACTIVATE NACK
message, which have been refused
Name Q3 : hoFailureIncomingIntraBssTchChannelActivateNack
Object : bts
Function : number of incoming intra BSS handover requests, on TCH with cause
receipt from the BTS of a CHANNEL ACTIVATE NACK message,
which have been refused
Event : receipt from the BTS of a CHANNEL ACTIVATE NACK message
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1758/3 Number of incoming intra BSS handover requests, on TCH with
cause expiration of TchnAck timer, which have been refused
Name Q3 : hoFailureIncomingIntraBssTchTchnAckTimerExp
Object : bts
Function : number of incoming intra BSS handover requests, on TCH with cause
expiration of TchnAck timer, which have been refused
Event : expiration of TchnAck timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1758/4 Number of incoming intra BSS handover requests, on TCH with
cause target cell and speech coding algorithm incompatible OR
target cell and channel mode incompatible AND no possible
fallback
Name Q3 : hoFailureIncomingIntraBssTchIncompatible
Object : bts
Function : number of incoming intra BSS handover requests, on TCH with cause
target cell and speech coding algorithm incompatible OR target cell
and channel mode incompatible AND no possible fallback
Event : target cell and speech coding algorithm incompatible OR target cell
and channel mode incompatible AND no possible fallback
Type : raw permanent
Class : handover
Source : recorded by the BSC
Note: Incompatibility for target cell can be hardware (14K5 or HSCSD) or
configuration (EFR & 14K5 & HSCSD).
l
1759/0 Number of incoming intra BSS handover requests, on SDCCH
with cause lack of radio resources, which have been refused
Name Q3 : hoFailureIncomingIntraBssSdcchRadioLack
Object : bts
Function : number of incoming intra BSS handover requests, on SDCCH with
cause lack of radio resources, which have been refused
l
1759/3 Number of incoming intra BSS handover requests, on SDCCH
with cause expiration of TchnAck timer, which have been refused
Name Q3 : hoFailureIncomingIntraBssSdcchTchnAckTimerExp
Object : bts
Function : number of incoming intra BSS handover requests, on SDCCH with
cause expiration of TchnAck timer, which have been refused
Event : expiration of TchnAck timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1760/0 Number of incoming inter BSS handover requests, on TCH with
cause lack of radio resources, which have been refused
Name Q3 : hoFailureIncomingInterBssTchRadioLack
Object : bts
Function : number of incoming inter BSS handover requests, on TCH with cause
lack of radio resources, which have been refused
Event : lack of radio resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1760/1 Number of incoming inter BSS handover requests, on TCH with
cause lack of terrestrial resources, which have been refused
Name Q3 : hoFailureIncomingInterBssTchTerrestLack
Object : bts
Function : number of incoming inter BSS handover requests, on TCH with cause
lack of terrestrial resources, which have been refused
Event : lack of terrestrial resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1760/2 Number of incoming inter BSS handover requests, on TCH with
cause incoming handover not allowed in the cell, which have been
refused
Name Q3 : hoFailureIncomingInterBssTchHoNotAllowed
Object : bts
Function : number of incoming inter BSS handover requests, on TCH with cause
incoming handover not allowed in the cell, which have been refused
Event : incoming handover not allowed in the cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1760/3 Number of incoming inter BSS handover requests, on TCH with
cause receipt from the BTS of a CHANNEL ACTIVATE NACK
message, which have been refused
Name Q3 : hoFailureIncomingInterBssTchChannelActivateNack
Object : bts
Function : number of incoming inter BSS handover requests, on TCH with cause
receipt from the BTS of a CHANNEL ACTIVATE NACK message,
which have been refused
Event : receipt from the BTS of a CHANNEL ACTIVATE NACK message
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1760/4 Number of incoming inter BSS handover requests, on TCH with
cause expiration of TchnAck timer, which have been refused
Name Q3 : hoFailureIncomingInterBssTchTchnAckTimerExp
Object : bts
Function : number of incoming inter BSS handover requests, on TCH with cause
expiration of TchnAck timer, which have been refused
Event : expiration of TchnAck timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1760/5 Number of incoming inter BSS handover requests, on TCH with
cause CIC and speech coding algorithm incompatible OR target
cell and speech coding algorithm incompatible OR CIC and
channel mode incompatible OR target cell and channel mode
incompatible AND no possible fallback
Name Q3 : hoFailureIncomingInterBssTchCICIncompatible
Object : bts
Function : number of incoming inter BSS handover requests, on TCH with cause
CIC and speech coding algorithm incompatible OR target cell and
speech coding algorithm incompatible OR CIC and channel mode
incompatible OR target cell and channel mode incompatible AND no
possible fallback
Event : CIC and speech coding algorithm incompatible OR target cell and
speech coding algorithm incompatible OR CIC and channel mode
incompatible OR target cell and channel mode incompatible AND no
possible fallback
Type : raw permanent
Class : handover
Source : recorded by the BSC
Note : Incompatibility for CIC can be hardware or configuration.
Incompatibility for target cell can be hardware or configuration.
l
1761/0 Number of incoming inter BSS handover requests, on SDCCH
with cause lack of radio resources, which have been refused
Name Q3 : hoFailureIncomingInterBssSdcchRadioLack
Object : bts
Function : number of incoming inter BSS handover requests, on SDCCH with
cause lack of radio resources, which have been refused
Event : lack of radio resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1761/1 Number of incoming inter BSS handover requests, on SDCCH
with cause lack of terrestrial resources, which have been refused
Name Q3 : hoFailureIncomingInterBssSdcchTerrestLack
Object : bts
Function : number of incoming inter BSS handover requests, on SDCCH with
cause lack of terrestrial resources, which have been refused
Event : lack of terrestrial resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1761/2 Number of incoming inter BSS handover requests, on SDCCH
with cause incoming handover not allowed in the cell, which have
been refused
Name Q3 : hoFailureIncomingInterBssSdcchHoNotAllowed
Object : bts
Function : number of incoming inter BSS handover requests, on SDCCH with
cause incoming handover not allowed in the cell, which have been
refused
Event : incoming handover not allowed in the cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1761/3 Number of incoming inter BSS handover requests, on SDCCH
with cause receipt from the BTS of a CHANNEL ACTIVATE
NACK message, which have been refused
Name Q3 : hoFailureIncomingInterBssSdcchChannelActivateNack
Object : bts
Function : number of incoming inter BSS handover requests, on SDCCH with
cause receipt from the BTS of a CHANNEL ACTIVATE NACK
message, which have been refused
Event : receipt from the BTS of a CHANNEL ACTIVATE NACK message
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1761/4 Number of incoming inter BSS handover requests, on SDCCH
with cause expiration of TchnAck timer, which have been refused
Name Q3 : hoFailureIncomingInterBssSdcchTchnAckTimerExp
Object : bts
Function : number of incoming inter BSS handover requests, on SDCCH with
cause expiration of TchnAck timer, which have been refused
Event : expiration of TchnAck timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1762/0 Number of outgoing intra BSS handover requests, on TCH with
cause lack of radio resources, which have been refused
Name Q3 : hoFailureOutgoingIntraBssTchRadioLack
Object : bts
Function : number of outgoing intra BSS handover requests, on TCH with cause
lack of radio resources, which have been refused
Event : lack of radio resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1762/1 Number of outgoing intra BSS handover requests, on TCH with
cause incoming handover not allowed in the cell, which have been
refused
Name Q3 : hoFailureOutgoingIntraBssTchHoNotAllowed
Object : bts
Function : number of outgoing intra BSS handover requests, on TCH with cause
incoming handover not allowed in the cell, which have been refused
Event : incoming handover not allowed in the cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1762/2 Number of outgoing intra BSS handover requests, on TCH
with cause receipt from the BTS of a CHANNEL ACTIVATE
NACK message, which have been refused
Name Q3 : hoFailureOutgoingIntraBssTchChannelActivateNack
Object : bts
Function : number of outgoing intra BSS handover requests, on TCH with cause
receipt from the BTS of a CHANNEL ACTIVATE NACK message,
which have been refused
Event : receipt from the BTS of a CHANNEL ACTIVATE NACK message
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1762/3 Number of outgoing intra BSS handover requests, on TCH with
cause expiration of TchnAck timer, which have been refused
Name Q3 : hoFailureOutgoingIntraBssTchTchnAckTimerExp
Object : bts
Function : number of outgoing intra BSS handover requests, on TCH with cause
expiration of TchnAck timer, which have been refused
Event : expiration of TchnAck timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1762/4 Number of outgoing intra BSS handover requests, on TCH with
cause expiration of TchnAck timer, which have been refused
Name Q3 : hoFailureOutgoingIntraBssTchIncompatible
Object : bts
Function : number of outgoing intra BSS handover requests, on TCH with cause
target cell and speech coding algorithm incompatible OR target cell
and channel mode incompatible AND no possible fallback, which
have been refused
Event : target cell and speech coding algorithm incompatible OR target cell
and channel mode incompatible AND no possible fallback
Type : raw permanent
Class : handover
Source : recorded by the BSC
Note : Incompatibility for target cell can be hardware or configuration
l
1763/0 Number of outgoing intra BSS handover requests, on SDCCH
with cause lack of radio resources, which have been refused
Name Q3 : hoFailureOutgoingIntraBssSdcchRadioLack
Object : bts
Function : number of outgoing intra BSS handover requests, on SDCCH with
cause lack of radio resources, which have been refused
Event : lack of radio resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1763/1 Number of outgoing intra BSS handover requests, on SDCCH
with cause incoming handover not allowed in the cell, which have
been refused
Name Q3 : hoFailureOutgoingIntraBssSdcchHoNotAllowed
Object : bts
Function : number of outgoing intra BSS handover requests, on SDCCH with
cause incoming handover not allowed in the cell, which have been
refused
Event : incoming handover not allowed in the cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1763/2 Number of outgoing intra BSS handover requests, on SDCCH
with cause receipt from the BTS of a CHANNEL ACTIVATE
NACK message, which have been refused
Name Q3 : hoFailureOutgoingIntraBssSdcchChannelActivateNack
Object : bts
Function : number of outgoing intra BSS handover requests, on SDCCH with
cause receipt from the BTS of a CHANNEL ACTIVATE NACK
message, which have been refused
Event : receipt from the BTS of a CHANNEL ACTIVATE NACK message
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1763/3 Number of outgoing intra BSS handover requests, on SDCCH
with cause expiration of TchnAck timer, which have been refused
Name Q3 : hoFailureOutgoingIntraBssSdcchTchnAckTimerExp
Object : bts
Function : number of outgoing intra BSS handover requests, on SDCCH with
cause expiration of TchnAck timer, which have been refused
Event : expiration of TchnAck timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1764/0 Number of outgoing inter BSS handover requests, on TCH with
cause lack of radio resources, which have been refused
Name Q3 : hoFailureOutgoingInterBssTchRadioLack
Object : bts
Function : number of outgoing inter BSS handover requests, on TCH with cause
lack of radio resources, which have been refused
Event : lack of radio resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1764/1 Number of outgoing inter BSS handover requests, on TCH with
cause lack of terrestrial resources, which have been refused
Name Q3 : hoFailureOutgoingInterBssTchTerrestLack
Object : bts
Function : number of outgoing inter BSS handover requests, on TCH with cause
lack of terrestrial resources, which have been refused
Event : lack of terrestrial resources
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1764/2 Number of outgoing inter BSS handover requests, on TCH with
cause incoming handover not allowed in the cell, which have been
refused
Name Q3 : hoFailureOutgoingInterBssTchHoNotAllowed
Object : bts
Function : number of outgoing inter BSS handover requests, on TCH with cause
incoming handover not allowed in the cell, which have been refused
Event : incoming handover not allowed in the cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1764/3 Number of outgoing inter BSS handover requests, on TCH with
cause T7 timer expiration, which have been refused
Name Q3 : hoFailureOutgoingInterBssTchT7TimerExp
Object : bts
Function : number of outgoing inter BSS handover requests, on TCH with cause
T7 timer expiration, which have been refused
Event : T7 timer expiration
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1764/4 Number of outgoing inter BSS handover requests, on TCH with
cause “every other cases”, which have been refused
Name Q3 : hoFailureOutgoingInterBssTchOtherCases
Object : bts
Function : number of outgoing inter BSS handover requests, on TCH with cause
“every other cases”, which have been refused
Event : “every other cases”
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1764/5 Number of outgoing inter BSS handover requests, on TCH with
cause CIC and speech coding algorithm incompatible OR target
cell and speech coding algorithm incompatible OR CIC and
channel mode incompatible OR target cell and channel mode
incompatible AND no possible fallback, which have been
refused
Name Q3 : hoFailureOutgoingInterBssTchIncompatible
Object : bts
Function : number of outgoing inter BSS handover requests, on TCH with cause
CIC and speech coding algorithm incompatible OR target cell and
speech coding algorithm incompatible OR CIC and channel mode
incompatible OR target cell and channel mode incompatible AND no
possible fallback, which have been refused
l
1765/2 Number of outgoing inter BSS handover requests, on SDCCH
with cause incoming handover not allowed in the cell, which
have been refused
Name Q3 : hoFailureOutgoingInterBssSdcchHoNotAllowed
Object : bts
Function : number of outgoing inter BSS handover requests, on SDCCH with
cause incoming handover not allowed in the cell, which have been
refused
Event : incoming handover not allowed in the cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1765/3 Number of outgoing inter BSS handover requests, on SDCCH
with cause T7 timer expiration, which have been refused
Name Q3 : hoFailureOutgoingInterBssSdcchT7TimerExp
Object : bts
Function : number of outgoing inter BSS handover requests, on SDCCH with
cause T7 timer expiration, which have been refused
Event : T7 timer expiration
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1765/4 Number of outgoing inter BSS handover requests, on SDCCH
with cause “every other cases”, which have been refused
Name Q3 : hoFailureOutgoingInterBssSdcchOtherCase
Object : bts
Function : number of outgoing inter BSS handover requests, on SDCCH with
cause “every other cases”, which have been refused.
Event : “every other cases”
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1768/0 Number of failures to execute intra_bss handover from the cell
on TCH.
Name Q3 : hoUnsuccessOutgoingIntraCellTchReturnOldChannel
Object : bts
Function : number of failures to execute intra_bss handover from the cell caused
by a mobile that returns to the old channel (HANDOVER FAILURE
before T3103 timer expiration).
Event : mobile returns to the old channel (HANDOVER FAILURE before
T3103 timer expiration)
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1768/1 Number of failures to execute intra_bss handover from the cell
on TCH.
Name Q3 : hoUnsuccessOutgoingIntraCellTchT3103TimerExp
Object : bts
Function : number of failures to execute intra_bss handover from the cell caused
by T3103 timer expiration.
Event : T3103 timer expiration
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1769/0 Number of failures to execute intra_bss handover from the cell on
SDCCH.
Name Q3 : hoUnsuccessOutgoingIntraCellSdcchReturnOldChannel
Object : bts
Function : number of failures to execute intra_bss handover from the cell caused
by a mobile that returns to the old channel (HANDOVER FAILURE
before T3103 timer expiration).
Event : mobile returns to the old channel (HANDOVER FAILURE before
T3103 timer expiration)
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1769/1 Number of failures to execute intra_bss handover from the cell
on SDCCH.
Name Q3 : hoUnsuccessOutgoingIntraCellSdcchT3103TimerExp
Object : bts
Function : number of failures to execute intra_bss handover from the cell caused
by T3103 timer expiration.
Event : T3103 timer expiration
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1770/0 Number of refusals to accept an outgoing inter--cell handover on
TCH in the cell with cause mobile returns to the old channel
Name Q3 : hoUnsuccessOutgoingInterCellTchReturnOldChannel
Object : bts
Function : number of refusals to accept an outgoing inter--cell handover on TCH
in the cell with cause mobile returns to the old channel
Event : mobile returns to the old channel
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1770/1 Number of refusals to accept an outgoing inter--cell handover on
TCH in the cell with cause T3103 timer expiration
Name Q3 : hoUnsuccessOutgoingInterCellTchT3103TimerExp
hoUnsuccessOutgoingInterCellTchT3107TimerExp8w
Object : bts
Function : number of refusals to accept an outgoing inter--cell handover on TCH
in the cell with cause T3103 timer expiration
Event : T3103 timer expiration
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1770/2 Number of refusals to accept an outgoing inter--cell handover on
TCH in the cell with cause “every other cases”
Name Q3 : hoUnsuccessOutgoingInterCellTchOtherCases
Object : bts
Function : number of refusals to accept an outgoing inter--cell handover on TCH
in the cell with cause “every other cases”
Event : “every other cases”
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1771/0 Number of refusals to accept an outgoing inter--cell handover on
SDCCH in the cell with cause mobile returns to the old channel
Name Q3 : hoUnsuccessOutgoingInterCellSdcchReturnOldChannel
Object : bts
Function : number of refusals to accept an outgoing inter--cell handover on
SDCCH in the cell with cause mobile returns to the old channel
Event : mobile returns to the old channel
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1771/1 Number of refusals to accept an outgoing inter--cell handover on
SDCCH in the cell with cause T3103 timer expiration
Name Q3 : hoUnsuccessOutgoingInterCellSdcchT3103TimerExp
Object : bts
Function : number of refusals to accept an outgoing inter--cell handover on
SDCCH in the cell with cause T3103 timer expiration
Event : T3103 timer expiration
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1771/2 Number of refusals to accept an outgoing inter--cell handover on
SDCCH in the cell with cause “every other cases”
Name Q3 : hoUnsuccessOutgoingInterCellSdcchOtherCases
Object : bts
Function : number of refusals to accept an outgoing inter--cell handover on
SDCCH in the cell with cause “every other cases”
Event : “every other cases”
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1772/0 Number of failures to execute intra_bss handover to the cell on
TCH.
Name Q3 : hoUnsuccessIncomingIntraCellTchReturnOldChannel
Object : bts
Function : number of failures to execute intra_bss handover to the cell on TCH
caused by a mobile that returns to the old channel (HANDOVER
FAILURE before T3103 timer expiration).
Event : mobile returns to the old channel (HANDOVER FAILURE before
T3103 timer expiration)
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1772/1 Number of failures to execute intra_bss handover to the cell on
TCH.
Name Q3 : hoUnsuccessIncomingIntraCellTchT3103TimerExp
Object : bts
Function : number of failures to execute intra_bss handover to the cell on TCH
caused by T3103 timer expiration.
Event : T3103 timer expiration
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1773/0 Number of failures to execute intra_bss handover to the cell on
SDCCH.
Name Q3 : hoUnsuccessIncomingIntraCellSdcchReturnOldChannel
Object : bts
Function : number of failures to execute intra_bss handover to the cell on
SDCCH caused by a mobile that returns to the old channel
(HANDOVER FAILURE before T3103 timer expiration).
Event : mobile returns to the old channel (HANDOVER FAILURE before
T3103 timer expiration)
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1773/1 Number of failures to execute intra_bss handover to the cell on
SDCCH.
Name Q3 : hoUnsuccessIncomingIntraCellSdcchT3103TimerExp
Object : bts
Function : number of failures to execute intra_bss handover to the cell on
SDCCH caused by T3103 timer expiration.
Event : T3103 timer expiration
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1774/0 Number of refusals to accept an incoming inter--bss handover on
TCH in the cell with cause timer expiration
Name Q3 : hoUnsuccessIncomingInterBssTchTimerExp
Object : bts
Function : number of refusals to accept an incoming inter--bss handover on TCH
in the cell with cause timer expiration
Event : timer expiration (expiration of ThndCom timer before receipt of
ABIS HANDOVER COMPLETE from the MSC or receipt of
CLEAR COMMAND message from the MSC)
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1774/1 Number of refusals to accept an incoming inter--bss handover on
TCH in the cell with cause “every other cases”
Name Q3 : hoUnsuccessIncomingInterBssTchOtherCases
Object : bts
Function : number of refusals to accept an incoming inter--bss handover on TCH
in the cell with cause “every other cases”
Event : “every other cases” (receipt of a CLEAR COMMAND message with
a cause set to a different value than “handover successful” or “Call
control”
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1775/0 Number of refusals to accept an incoming inter--bss handover on
SDCCH in the cell with cause timer expiration
Name Q3 : hoUnsuccessIncomingInterBssSdcchTimerExp
Object : bts
Function : number of refusals to accept an incoming inter--bss handover on
SDCCH in the cell with cause timer expiration
Event : timer expiration (expiration of ThndCom timer before receipt of
ABIS HANDOVER COMPLETE from the MSC or receipt of
CLEAR COMMAND message from the MSC)
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
1775/1 Number of refusals to accept an incoming inter--bss handover on
SDCCH in the cell with cause “every other cases”
Name Q3 : hoUnsuccessIncomingInterBssSdcchOtherCases
Object : bts
Function : number of refusals to accept an incoming inter--bss handover on
SDCCH in the cell with cause “every other cases”
l
1778 Number of abnormal releases while the communication is in “sig-
nalling phase” and a cell associated to the communication
Name Q3 : signallingAbnormalReleaseCell
Object : bts
Function : number of abnormal releases while the communication is in
“signalling phase” and a cell associated to the communication
Event : All the event causes of 1163/n counters except those of 1163/5 and
1163/24 counters
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1779 Number of abnormal releases while the communication is in
“traffic phase”
Name Q3 : trafficAbnormalRelease
Object : bts
Function : number abnormal releases while the communications is in “traffic
phase”
Event : All the event causes of 1164/n counters except the one of 1164/20
counter
Type : raw permanent
Class : release
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1783 Number of outgoing handovers requested by dualband mobiles
from the main frequency band to the same frequency band of the
network
Name Q3 : hoRequestOutgoingMbandMbandMsDualb
Object : bts
Function : number of outgoing, intra-bss or inter-bss handovers, on TCH,
requested from the main frequency band to the same frequency band
of the network
Event : attempt to select a resource of an eligible cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Feature : Dualband cell management (TF875 - V12)
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Note : The originated and target resources are in the main frequency band of
the network.
l
1784 Number of outgoing handovers requested by dualband mobiles
from the second frequency band to the same frequency band of
the network
Name Q3 : hoRequestOutgoingEbandEbandMsDualb
Object : bts
Function : number of outgoing, intra-bss or inter-bss handovers, on TCH,
requested from the second frequency band to the same frequency
band of the network
l
1785 Number of outgoing handovers requested by dualband mobiles
from the second frequency band to the main frequency band of
the network
Name Q3 : hoRequestOutgoingEbandMbandMsDualb
Object : bts
Function : number of outgoing, intra-bss or inter-bss handovers, on TCH,
requested from the second frequency band the main frequency band of
the network
Event : attempt to select a resource of an eligible cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Feature : Dualband cell management (TF875 - V12)
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Note : The target resource is in the main frequency band of the network
whereas the originated resource is in the second frequency band.
l
1786 Number of successful outgoing handovers for dualband mobiles
from the main frequency band to the same frequency band of the
network
Name Q3 : hoSuccessOutgoingMbandMbandMsDualb
Object : bts
Function : number of successful outgoing, intra-bss or inter-bss handovers, on
TCH, from the main frequency band to the same frequency band of
the network
Event : receipt of CLEAR COMMAND with cause “handover successful”
(inter-bss handover) or receipt of HANDOVER COMPLETE from
the MS (intra-bss handover)
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1788 Number of successful outgoing handovers for dualband mobiles
from the second frequency band to the main frequency band of
the network
Name Q3 : hoSuccessOutgoingEbandMbandMsDualb
Object : bts
Function : number of successful outgoing, intra-bss or inter-bss handovers, on
TCH, from the second frequency band to the main frequency band of
the network
Event : receipt of CLEAR COMMAND with cause “handover successful”
(inter-bss handover) or receipt of HANDOVER COMPLETE from
the MS (intra-bss handover)
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Feature : Dualband cell management (TF875 - V12)
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1789 Number of outgoing handover executions by dualband mobiles
for the cell from the main frequency band to the second
frequency band of the network
Name Q3 : hoExecutionOutgoingMbandEbandMsDualb
Object : bts
Function : number of outgoing handover (intra-bss or inter-bss) executions by
dualband mobiles for the cell, from the main frequency band to the
second frequency band of the network
l
1792 Number of outgoing handover executions by dualband mobiles
for the cell from the second frequency band to the main
frequency band of the network
Name Q3 : hoExecutionOutgoingEbandMbandMsDualb
Object : bts
Function : number of outgoing handover (intra-bss or inter-bss) executions by
dualband mobiles for the cell, from the second frequency band to the
main frequency band of the network
Event : transmission of ASSIGN COMMAND message
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Feature : Dualband cell management (TF875 - V12)
Data flows : Refer to Chapter 2
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1793 Number of incoming intra BSS handovers on TCH requested by
dualband mobiles
Name Q3 : hoRequestIncomingIntraBssTchMsDualb
Object : bts
Function : number of incoming intra BSS handover requests on TCH in the cell
for dualband mobiles
l
1796 Number of intra-bts handovers on TCH requested by dualband
mobiles
Name Q3 : hoRequestIntraBtsMsDualb
Object : bts
Function : number of intra-bts handovers on TCH requested in the cell by
dualband mobiles
Event : attempt to select a TCH in the cell
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Feature : Dualband cell management (TF875 - V12)
Note : This counter is incremented at the end of the handover.
l
1797 Number of intra-bts handovers on TCH executed for dualband
mobiles
Name Q3 : hoExecutionIntraBtsMsDualb
Object : bts
Function : number of attempts to execute intra-bts handovers on TCH in the cell
by dualband mobiles
Event : transmission of ASSIGN COMMAND message
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
l
1798 Number of successful intra-bts handovers on TCH for dualband
mobiles
Name Q3 : hoSuccessIntraBtsMsDualb
Object : bts
Function : number of successful intra-bts handovers on TCH in the cell for
dualband mobiles
Event : receipt of ASSIGN COMPLETE from the mobile
Type : raw permanent
Class : handover
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Feature : Dualband cell management (TF875 - V12)
l
1799 Number of direct allocations of TCHs in the second band (or
zone) of a dualband (or concentric or dual--coupling) cell
Name Q3 : assignToOtherBandOrZone
Object : bts
Function : number of direct allocations of TCHs in the second band (or zone) of a
dualband (or concentric or dual--coupling) cell
Event : receipt of an ASSIGN COMPLETE message on TCH or preempted
PDTCH from the mobile
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Feature : Dualband cell management (TF875 - V12)
l
1800/0 Number of handovers performed on the talker side of a VBS call
in the cell
Name Q3 : asciTalkerHandoverVbs
Object : bts
Function : number of handovers performed on the talker side of a VBS call in the
cell
Event : receipt of HO_COMPLETE, CLEAR_COMMAND,
ASSIGN_COMPLETE messages
Type : raw permanent
Class : asci
Source : recorded by the BSC
Feature : GSM--R (V12)
Precise
incrementation conditions :
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
l
1800/1 Number of handovers performed on the talker side of a VGCS
call in the cell
Name Q3 : asciTalkerHandoverVgcs
Object : bts
Function : number of handovers performed on the talker side of a VGCS call in
the cell
l
1806 Number of MS decrement power controls ordered by the Layer
One Management
Name Q3 : msPowerDecControl
Object : bts
Function : number of MS decrement power controls ordered by the Layer One
Management
l
1809/0 Average timing advance value for the communications in the cell
Name Q3 : timingAdvanceAverage
timingAdvanceAverageTrZone
Object : bts/transceiverZone
Function : average timing advance value for the communications in the the cell
(only for communications on TCH channel)
Event : receipt of a STOP MEASUREMENT ACK message from the BTS
Type : raw permanent
Class : asci
Source : recorded by the BSC
Feature : GSM--R (V12)
Precise
incrementation conditions :
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Radio channel release DEACTIVATE SACCH ACK
procedure (normal completion)”
DFD “Radio channel release RELEASE INDICATION procedure
(normal completion)
DFD “Connection clearing required by the BSC procedure
(communication on TRAFFIC phase)”
Note : The value given by the BTS is the average timing advance per
communication (this value is multiplied by the C1600 value:
connectionDurationTch)
l
1809/1 Maximum timing advance value for the communications in the
cell
Name Q3 : timingAdvanceMaximum
timingAdvanceMaximumTrZone
Object : bts/transceiverZone
Function : maximum timing advance value for the communications in the inner
or the outer zone of the cell (only for communications on TCH
channel)
Event : receipt of a STOP MEASUREMENT ACK message from the BTS
Type : raw permanent
Class : asci
Source : recorded by the BSC
Feature : GSM--R (V12)
Precise
incrementation conditions :
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “inter--cell intra BSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “connection clearing required by the MSC procedure
(normal completion with communication on SIGNALLING
phase)”
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
DFD “Radio channel release DEACTIVATE SACCH ACK
procedure (normal completion)”
l
1811 Average and maximum numbers of configurated SDCCH
resource
Name Q3 : sdcchAverageConfiguratedMoy
sdcchAverageConfiguratedMax
sdcchAverageConfiguratedCum
sdcchAverageConfiguratedEch
sdcchAverageConfiguratedTrZoneMoy
sdcchAverageConfiguratedTrZoneMax
sdcchAverageConfiguratedTrZoneCum
sdcchAverageConfiguratedTrZoneEch
Object : bts/transceiverZone
Function : average and maximum numbers of configurated SDCCH resource
(= resource configured by the OMC; it can be available or
unavailable)
Event : receipt of a TGE from the OMC modifying the number of SDCCH
resources in the inner or the outer zone of the cell
Type : raw permanent
Class : asci
Source : recorded by the BSC
Feature : GSM--R (V12)
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
Note : This resource configured by the OMC may be available or not.
l
1812 Number of activated and non activated circuit TS for traffic in
circuit mode in the inner or the outer zone of the cell
Name Q3 : allocatedCircuitTsMoy
allocatedCircuitTsMax
allocatedCircuitTsCum
allocatedCircuitTsEch
allocatedCircuitTsTrZoneCum
allocatedCircuitTsTrZoneMax
allocatedCircuitTsTrZoneMoy
allocatedCircuitTsTrZoneEch
Object : bts/transceiverZone
Function : Minimum, maximum, average, and cumulative number of activated
and non activated circuit TS (all TCHs and PDTCHs activated for
traffic in circuit mode) in the inner or outer zone of the cell
Event : allocation of a TCH or a PDTCH for traffic in circuit mode
Type : raw permanent
Class : GPRS
Source : recorded by the BSC
Feature : GPRS (TF1121 and TF1128 - V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
When new counter 1821 is received, its value is copied in counter
1812.
l
1814 Number of GPRS preemption successes
Name Q3 : gprsPreemption
Object : bts
Function : number of PDTCH preemption successes
Event : successful preemption of a PDTCH in circuit mode
Type : raw permanent
Class : GPRS
Source : recorded by the BSC
Feature : GPRS (TF1121 - V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by CCP only
(Circuit Calls on PDTCH preempted to make a TCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure - preemption on PDTCH (normal
completion in the case of Mobile Originating Call)”
DFD “GPRS procedure (no resource available for a PDTCH
preemption)”
l
1815 Number of GPRS preemption failures (requests nacked by the
PCU)
Name Q3 : gprsPreemptionNack
Object : bts
Function : number of PDTCH preemption failures (requests nacked by the PCU)
Event : receipt of a refusal message from the PCU to release its PDTCH
channel
Type : raw permanent
Class : GPRS
Source : recorded by the BSC
Feature : GPRS (TF1121 - V12)
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by CCP only
(Circuit Calls on PDTCH preempted to make a TCH channel).
1824/3 Average and maximum number of WPS full rate TCH allocations
Name Q3 : tchFrAveragedUsedWpsCellMoy,
tchFrAveragedUsedWpsCellMax,
tchFrAveragedUsedWpsCellCum,
tchFrAveragedUsedWpsCellEch.
Object : bts
Function : average and maximum number of full rate TCH allocations or
preempted PDTCH (for screening 0 and 3). This counter has the same
definition as the counter 1611, only the location is different.
Event : allocation of a TCH channel or a preempted PDTCH for a WPS call.
Type : raw permanent
Class : GPRS
Precise
incrementation conditions : When GPRS is activated, this counter is
concerned by CCT (Circuit calls on TCH channel), but not by CCP (Circuit Calls on
PDTCH preempted to make a TCH channel). This is because this counter is related
to configured (static) TCH/FR channel. This counter is pegged on the traffic channel
allocation for a WPS call if the WPS Management flag is enabled. This counter is
pegged on the traffic channel de--allocation for a call inititiated as a WPS call.
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
To sum it up, this counter is related to TCH/FR channel, preemptable
PDTCH and PDTCH not allocated to PCUSN.
Event : Reception of a TGE from the OMC modifying the number of TCH
resources in the cell.
Type : raw permanent
Class : GPRS
Precise
incrementation conditions :
This counter is concerned by CCT (Circuit Calls on TCH channels)
but not by CCP (Circuit Calls on PDTCH preempted to make a TCH
channel) or by CP (Com packet on PDTCH channel), merely because
GPRS and GSM--R cannot be activated at the same time.
Note : V15.1R counter
l
1828/0 Allocation of a half rate TCH or a preempted PDTCH
Name Q3 : tchHrAveragedUsedCellMoy
tchHrAveragedUsedCellMax
tchHrAveragedUsedCellCum
tchHrAveragedUsedCellEch
Object : bts
Function : Average and maximum number of half rate TCH (including PDTCH)
allocations
Event : Allocation/de--allocation of a half rate TCH
Type : raw permanent
Class : allocation
Feature : 3000 public access bandwidth protection (22465)
Source : recorded by the BSC
l
1828/1 Allocation of a half rate TCH or a preempted PDTCH for a WPS
call
Name Q3 : tchHrAveragedUsedWpsCellMoy
tchHrAveragedUsedWpsCellMax
tchHrAveragedUsedWpsCellCum
tchHrAveragedUsedWpsCellEch
Object : bts
Function : Average and maximum number of half rate TCH (including PDTCH)
allocations
Event : Allocation/de--allocation of a half rate TCH
Type : raw permanent
Class : allocation
l
1840/5 Number of outgoing intra--bss or inter--bss handover successes
from a central cell to a neighboring one: Distance
Name Q3 : hoNcellsSuccessOutgoingPowerBudget
Object : adjacentCellHandOver
Function : number of outgoing intra--bss or inter--bss handover successes from a
central cell to a neighboring one because of power budget
Event : receipt of a CLEAR COMMAND message from the MSC with a
cause set to “handover successful” (inter--bss handovers) or receipt of
a HANDOVER COMPLETE message (intra--bss handovers)
Type : raw permanent
Class : asci
Source : recorded by the BSC
Data flows : Refer to Chapter 2
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Feature : GSM--R (V12)
Object : This counter only applies on TCH channel.
l
1840/6 Number of outgoing intra--bss or inter--bss handover successes
from a central cell to a neighboring one: Directed retry
Name Q3 : hoNcellsSuccessOutgoingDirectedRetry
Object : adjacentCellHandOver
Function : number of outgoing intra--bss or inter--bss handover successes from a
central cell to a neighboring one because of directed retry
Event : receipt of a CLEAR COMMAND message from the MSC with a
cause set to “handover successful” (inter--bss handovers) or receipt of
a HANDOVER COMPLETE message (intra--bss handovers)
Type : raw permanent
Class : asci
Source : recorded by the BSC
Data flows : Refer to Chapter 2
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
Feature : GSM--R (V12)
Object : This counter only applies on TCH channel.
l
1840/7 Number of outgoing intra--bss or inter--bss handover successes
from a central cell to a neighboring one: Forced handover O&M
Name Q3 : hoNcellsSuccessOutgoingInterCellOM
Object : adjacentCellHandOver
Function : number of outgoing intra--bss or inter--bss handover successes from a
central cell to a neighboring one with cause “forced handover” from
the L1M
Event : receipt of a CLEAR COMMAND message from the MSC with a
cause set to “handover successful” (inter--bss handovers) or receipt of
a HANDOVER COMPLETE message (intra--bss handovers)
Type : raw permanent
Class : asci
Source : recorded by the BSC
Data flows : Refer to Chapter 2
DFD “Intra cell handover procedure (normal completion with
communication on TRAFFIC phase)”
DFD “Inter BSS intra MSC handover procedure (normal
completion with communication on TRAFFIC phase)”
l
1842/0 Number of emission of ASSIGNMENT FAILURE messages on
the A interface: Modification from an SDCCH channel to a TCH
or a preempted PDTCH channel
Name Q3 : assignRequestAintSdcchToTchChannel
Object : bts
Function : number of ASSIGNMENT FAILURE messages sent on the
A interface because of a modification from a SDCCH channel to a
TCH or a preempted PDTCH channel
Event : sending of an ASSIGNMENT FAILURE message to the MSC
because of a modification from a SDCCH channel to a TCH or a
preempted PDTCH channel
Type : raw permanent
Class : assignment
Source : recorded by the BSC
Precise
incrementation conditions :
When GPRS is activated, this counter is concerned by the following
calls:
CCT: Circuit calls on TCH channel
CCP: Circuit Calls on PDTCH preempted to make a TCH channel
But it is not concerned by CP calls (Com packet on PDTCH channel).
Data flows : Refer to Chapter 2
DFD “GPRS procedure (negative acknowledgement by the PCU
for a PDTCH preemption)”
DFD “GPRS procedure (no resource available for a PDTCH
preemption)”
DFD “dedicated channel assignment procedure (no resource
available and queuing not activated)”
l
1842/1 Number of emission of ASSIGNMENT FAILURE messages on
the A interface: Cause other than modification from a SDCCH
channel to a TCH or a preempted PDTCH channel
Name Q3 : assignRequestAintOthers
Object : bts
Function : number of ASSIGNMENT FAILURE messages sent on the
A interface because of a cause other than a modification from a
SDCCH channel to a TCH or a preempted PDTCH channel
Object : bts
Function : Total number of priority 1 WPS requests dropped when the time spent
by WPS request exceeds the maximum queue timer.
Event : WPS global flag is activated
Type : raw permanent
2012/1 Total number of priority 2 WPS requests dropped when the time
spent by WPS request exceeds the maximum queue timer.
Name Q3 : WQTOUT2
Object : bts
Function : Total number of priority 2 WPS requests dropped when the time spent
by WPS request exceeds the maximum queue timer.
Event : WPS global flag is activated
Type : raw permanent
Feature : WPS BSS2G and 3000 queuing mechanism enhancement (22463)
Source : recorded by the BSC
Note : V15 counter
l
2012/2 Total number of priority 3 WPS requests dropped when the time
spent by WPS request exceeds the maximum queue timer.
Name Q3 : WQTOUT3
Object : bts
Function : Total number of priority 3 WPS requests dropped when the time spent
by WPS request exceeds the maximum queue timer.
Event : WPS global flag is activated
Type : raw permanent
Feature : WPS BSS2G and 3000 queuing mechanism enhancement (22463)
Source : recorded by the BSC
Note : V15 counter
l
2012/3 Total number of priority 4 WPS requests dropped when the time
spent by WPS request exceeds the maximum queue timer.
Name Q3 : WQTOUT4
Object : bts
Function : Total number of priority 4 WPS requests dropped when the time spent
by WPS request exceeds the maximum queue timer.
l
2013/1 Duration that access class 11 has been barred during cell
congestion.
Name Q3 : wpsAccessBarringDurationClass11
Object : bts
Function : An access class is barred during cell congestion. Barred access classes
in the notAllowedAccessClasses parameter exclude the counter
triggering. Number of minutes the access class number 11 has been
barred.
Event : At each rotation of access classes (every 1 minute).
Type : raw permanent
Feature : WPS BSS2G and 3000 access class barring with class periodic
rotation. (22464)
Source : recorded by the BSC
Note : V15 counter
l
2013/2 Duration that access class 12 has been barred during cell
congestion.
Name Q3 : wpsAccessBarringDurationClass12
Object : bts
Function : An access class is barred during cell congestion. Barred access classes
in the notAllowedAccessClasses parameter exclude the counter
triggering. Number of minutes the access class number 12 has been
barred.
Event : At each rotation of access classes (every 1 minute).
Type : raw permanent
Feature : WPS BSS2G and 3000 access class barring with class periodic
rotation. (22464)
Source : recorded by the BSC
Note : V15 counter
l
2013/3 Duration that access class 13 has been barred during cell
congestion.
Name Q3 : wpsAccessBarringDurationClass13
Object : bts
Function : An access class is barred during cell congestion. Barred access classes
in the notAllowedAccessClasses parameter exclude the counter
triggering. Number of minutes the access class number 13 has been
barred.
Event : At each rotation of access classes (every 1 minute).
Type : raw permanent
Feature : WPS BSS2G and 3000 access class barring with class periodic
rotation. (22464)
Source : recorded by the BSC
Note : V15 counter
l
2013/4 Duration that access class 14 has been barred during cell
congestion.
Name Q3 : wpsAccessBarringDurationClass14
Object : bts
Function : An access class is barred during cell congestion. Barred access classes
in the notAllowedAccessClasses parameter exclude the counter
triggering. Number of minutes the access class number 14 has been
barred.
Event : At each rotation of access classes (every 1 minute).
Type : raw permanent
Feature : WPS BSS2G and 3000 access class barring with class periodic
rotation. (22464)
Source : recorded by the BSC
Note : V15 counter
l
2013/5 Duration that access class 15 has been barred during cell
congestion.
Name Q3 : wpsAccessBarringDurationClass15
Object : bts
Function : An access class is barred during cell congestion. Barred access classes
in the notAllowedAccessClasses parameter exclude the counter
triggering. Number of minutes the access class number 15 has been
barred.
Event : At each rotation of access classes (every 1 minute).
Type : raw permanent
Feature : WPS BSS2G and 3000 access class barring with class periodic
rotation. (22464)
Source : recorded by the BSC
Note : V15 counter
l
2014 Average and maximum number of WPS half rate TCH
allocations
Name Q3 : WPUBWPSQ
Object : bts
Function : Average and maximum number of WPS half rate TCH (including
PDTCH) allocations
Event : TCHA traffic channel becomes free and is allocated to a public call
while a WPS request is queued.
Type : raw permanent
Feature : WPS BSS2G and 3000 public access bandwidth protection (22465)
Source : recorded by the BSC
Note : V15 counter
l
2015 Total number of WPS requests removed from the queue
Name Q3 : WQABAND
Object : bts
Function : total number of WPS requests removed from the queue because of:
-- loss of radio contact with the MS Object Instance cell|
-- Clear command cause “call control” received from the MSC while
the WPS request is queued and no clear request previously sent
l
2035/0 Value of the msPowerClassToggle parameter
Name Q3 : msClassSensitivityToggle
Object : bts
Function : A msPowerClassToggle parameter is defined at the OMC--R level in
order to report MS 2W, MS 8W or MS 2W + 8W (no check on the
power class).
A list of ”toggling counters” is defined for which the BSC must take
into account the msPowerClassToggle.
Value of the msPowerClassToggle parameter :
0 : MS 2W
1 : MS 8W
2 : MS 2+8W
Event : At T2 expiration
Type : raw permanent
Source : recorded by BSC
Note : V15 counter
l
2036/0 Number of attempts of assignation of a TCH full rate or a
preempted PDTCH for MS 8W.
Name Q3 : attemptedTchFrSeizures8W
Object : bts
Function : number of attempts of assignation of a TCH full rate or a preempted
PDTCH for MS 8W
Event : transmission of an ASSIGN_COMMAND message to a MS 8W.
Type : raw permanent
Source : recorded by BSC
Note : V15 counter
l
2037/0 Number of successful TCH full rate or preempted PDTCH
assignations for MS 8W.
Name Q3 : successfulTchFrSeizures8W
Object : bts
Function : number of successful TCH full rate or preempted PDTCH
assignations for MS 8W
l
2050 Number of successful outgoing inter_bss handovers from the cell
for MS 8W only
Name Q3 : hoRequestOutgoingIntraBssSdcch8W
Object : bts
Function : number of outgoing intra_bss handover requests from the cell. The
counter is incremented at the end of the handover (success, selection
failure, execution failure or end of call) for MS 8W only.
Event : receipt of a CLEAR COMMAND message from the MSC with
handover cause set to hand_over successful
Type : raw permanent
Source : recorded by the BSC
Note : V15 counter
l
2051 Number of outgoing inter_bss handover requests from the cell
Name Q3 : hoRequestOutgoingInterBssSdcch8W
Object : bts
Function : Number of outgoing inter_bss handover requests from the cell. The
counter is incremented at the end of the handover (success, selection
failure, execution failure or end of call) for MS 8W only.
Event : attempt of selection of one of the cells of the list of the eligible cells
Type : raw permanent
Source : recorded by the BSC
Note : V15 counter
l
2052/0 Number of releases while the communication is in signalling
phase and cell associated to the communication, for MS 8W only
Name Q3 : signallingReleaseBts8w
Object : bts
Function : Number of releases while the communication is in signalling phase
and cell associated to the communication, for MS 8W only
l
2054 Number of receipts of an ESTABLISHMENT_INDICATION
message in call establishment phase (on SDCCH, or on TCH in
primo allocation (call re--establishment) or on overflowing), for
MS 8W only
Name Q3 : estabIndicSignallingEmergency8W
Object : bts
Function : Number of receipts of an ESTABLISHMENT_INDICATION
message in call establishment phase (on SDCCH, or on TCH in primo
allocation (call re--establishment) or on overflowing), for MS 8W
only
Event : receipt of a CM SERVICE REQUEST first L3 information message,
with a service type set to emergency call establishment
Type : raw permanent
Source : recorded by the BSC
Note : V15 counter
l
2056/0 Number of failures to execute intra--bss handover from the cell
for MS 8W only
Name Q3 : hoUnsuccessOutgoingIntraCellTchReturnOldChannel8W
Object : bts
Function : number of failures to execute intra--bss handover from the cell for
MS 8W only
Event : a MS 8W returns to the old channel (HANDOVER FAILURE) before
T3103 timer expiration)
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
2056/1 Number of failures to execute intra--bss handover from the cell
for MS 8W only
Name Q3 : hoUnsuccessOutgoingIntraCellTchT3103TimerExp8W
Object : bts
Function : number of failures to execute intra--bss handover from the cell for
MS 8W only.
Event : expiration of T3103 timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
2057/0 Number of refusals to accept an outgoing inter--cell handover on
TCH in the cell with cause mobile returns to the old channel
Name Q3 : hoUnsuccessOutgoingInterCellTchReturnOldChannel8W
Object : bts
Function : number of refusals to accept an outgoing inter--cell handover on TCH
in the cell with cause mobile returns to the old channel
Event : mobile returns to the old channel
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
2057/1 Number of refusals to accept an outgoing inter--cell handover on
TCH in the cell with cause T3103 (respectively T3107) timer
expiration for V12 (respectively V11)
Name Q3 : hoUnsuccessOutgoingInterCellTchT3103TimerExp8W
Object : bts
Function : number of refusals to accept an outgoing inter--cell handover on TCH
in the cell with cause T3103 (respectively T3107) timer expiration for
V12 (respectively V11)
Event : expiration of the T3103 timer
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
2058/0 Number of abnormal releases while the communication is in
“signalling” phase and cell associated to the communication, for
MS 8W only.
Name Q3 : signallingAbnormalReleaseCell8W
Object : bts
Function : number of abnormal releases while the communication is in
“signalling” phase and cell associated to the communication, for MS
8W only.
Event : All the previous screening except Expiration of T3101 timer before
receipt of ESTABLISHMENT INDICATION message, during an
Immediate Assignment procedure and “Receipt of a
CLEAR_COMMAND message from the MSC” (considered as
normal release).
Type : raw permanent
Class : handover
Source : recorded by the BSC
l
2059 Number of abnormal releases while the communication is in
“traffic” phase, for MS 8W only.
Name Q3 : trafficAbnormalRelease8W
Object : bts
Function : number of abnormal releases while the communication is in “traffic”
phase, for MS 8W only.
l
2061 At expiration of the listener detection timer, the group call
channel is released in the cell
Name Q3 : listenerDetectionExpiry
Object : bts
Function : At expiration of the listener detection timer, the group call channel is
released in the cell.
Event : at expiration of the listener detection timer
Type : raw permanent
Source : recorded by the BSC
Note : V15 counter
2068/0 Number of times the BSC does not perform a GPRS Resume proc.
Name Q3 : resumeFailureAfterHOInterRA
Object : bts
Function : Number of times the BSC does not perform a GPRS resume procedure
after a successful GPRS suspension. The GPRS attached MS has
performed an inter--RA handover (intra--BSC).
Event : The counter is increased when the BSC sends the RF Channel Release
on the initial RA after the HO Complete.
Type : raw permanent
Class : GPRS/EDGE
Source : recorded by the BSC
Feature : 25155 GPRS / EDGE Suspend and Resume
Precise
incrementation conditions :
The counter is increased in the cell of the initial RA where the RF
Channel Release is sent.
The counter is not incremented when the communication was not
successfully suspended.
In case of successive inter--RA HO, the counter is increased only
once, in the last cell of the initial RA.
Data flows : Refer to Chapter 2
GPRS / EDGE Suspend procedure with Resume message (failure
case)
Note : V15 counter
2068/1 Number of times the BSC does not perform a GPRS Resume proc.
Name Q3 : resumeFailureAfterHOInterBSC
Object : bts
Function : Number of times the BSC does not perform a GPRS resume procedure
after a successful GPRS suspension. The GPRS attached MS has
performed an inter--BSC handover.
Event : The BSC sends the RF Channel Release on the initial BSC after the
HO complete.
Type : raw permanent
Class : GPRS/EDGE
Source : recorded by the BSC
Feature : 25155 GPRS / EDGE Suspend and Resume
Precise
incrementation conditions :
The counter is increased in the cell of the initial BSC where the RF
Channel Release is sent.
The counter is not incremented when the communication was not
successfully suspended.
In case of successive inter--BSC HO, the counter is increased only
once, in the last cell of the initial BSC.
Data flows : Refer to Chapter 2
GPRS / EDGE Suspend procedure with Resume message (failure
case)
Note : V15 counter
ll
5102/0 Number of SS7 Level 2 errors: Negative ACK received
Name Q3 : ss7Level2ErrorNegAckRec
Object : signallingLink
Function : number of errors detected by Level 2 due to receipt of negative
acknowledgement of frames
Event : receipt by the BSC link of a request for retransmission on the SS7 link
from the remote MTP2
Type : raw temporary
Source : recorded by the BSC
l
5102/1 Number of SS7 Level 2 errors: Negative ACK sent
Name Q3 : ss7Level2ErrorNegAckTrans
Object : signallingLink
Function : number of errors detected by Level 2 due to transmission of negative
acknowledgement of frames
Event : transmission by the BSC of a request for retransmission on the SS7
link to the remote MTP2
Type : raw temporary
Source : recorded by the BSC
ll
5102/2 Number of SS7 Level 2 errors: MSU rejected for congestion
Name Q3 : ss7Level2ErrorMsuCongest
Object : signallingLink
Function : number of MSU frames rejected by MTP2 because of lack of internal
memory
Event : rejection of an MSU frame by MTP2 because of lack of internal
memory
Type : raw temporary
Source : recorded by the BSC
ll
5102/3 Number of SS7 Level 2 errors: SU error
Name Q3 : ss7Level2ErrorSuErr
Object : signallingLink
Function : number of errors detected by Level 2 because of errored SU
Event : receipt by the MTP2 of one of the following:
a frame with a false CRC
a frame too short (length equal or inferior to 2 bytes)
16 bytes in “OCM” byte counting mode
Type : raw temporary
Source : recorded by the BSC
ll
5103/0 Number of SS7 Level 3 errors: ACK delay exceeded
Name Q3 : ss7Level3ErrorDelay
Object : signallingLink
Function : number of errors detected by Level 3 because of lengthy delay in
acknowledgement messages
Event : Level 3 bssMapT7 time-out elapse
Type : raw temporary
Source : recorded by the BSC
ll
5103/1 Number of SS7 Level 3 errors: High error rate
Name Q3 : ss7Level3ErrorHighErrRate
Object : signallingLink
Function : number of errors detected by monitoring the error rate of SS7 frames
Event : detection by MTP2 of an excessive error rate, according to the
definition of the CCITT Q703 recommendation (Paragraph 10,
page 67)
Type : raw temporary
Source : recorded by the BSC
l
5603/0 Number of I frames received on sapi RSL
Name Q3 : abisInputIFrame
Object : bts
Function : number of I (Information) frames received from the cell TDMA
frames on RSL SAPI
Event : reception of an I frame on a RSL by the BSC
Type : raw temporary
Source : recorded by the BSC
l
5604/0 Number of UI bytes received on sapi RSL
Name Q3 : abisOutputUiByte
Object : bts
Function : number of UI (Unnumbered Information) bytes sent to the cell
TDMA frames on RSL SAPI
Event : transmission of a UI frame on a RSL by the BSC
Type : raw temporary
Source : recorded by the BSC
l
5605/0 Number of UI bytes sent on sapi RSL
Name Q3 : abisInputUiByte
Object : bts
Function : number of UI (Unnumbered Information) bytes received from the cell
TDMA frames on RSL SAPI
Event : receipt of a UI frame on a RSL by the BSC
Type : raw temporary
Source : recorded by the BSC
l
5606/0 Number of I bytes sent on sapi RSL
Name Q3 : abisOutputIByte
Object : bts
Function : number of I (Information) bytes sent to the cell TDMA frames on RSL
SAPI
Event : transmission of an I frame on a RSL by the BSC
Type : raw temporary
Source : recorded by the BSC
l
5607/0 Number of I bytes received on sapi RSL
Name Q3 : abisInputIByte
Object : bts
Function : number of I (Information) bytes received from the cell TDMA frames
on RSL SAPI
Event : receipt of an I frame on a RSL by the BSC
Type : raw temporary
Source : recorded by the BSC
l
5608/0 Number of Abis Level 2 errors: SUP received with PF 1
Name Q3 : abisLevel2ErrorRxSup1
Object : bts
Function : number of SUP (supervision) frames with the final bit set to 1 received
in established multiframe mode
Event : receipt of a SUP frame with the final bit set to 1 in established
multiframe mode by the BSC
Type : raw temporary
Source : recorded by the BSC
l
5608/1 Number of Abis Level 2 errors: DM received with PF 1
Name Q3 : abisLevel2ErrorRxDm1
Object : bts
Function : number of DM (Disconnected Mode) frames with the final bit set to 1
received in established multiframe mode
Event : receipt of a DM frame with the final bit set to 1 in established
multiframe mode by the BSC
Type : raw temporary
Source : recorded by the BSC
l
5608/2 Number of Abis Level 2 errors: UA received with PF 1
Name Q3 : abisLevel2ErrorRxUa1
Object : bts
Function : number of UA (Unnumbered Acknowledge) frames with the final bit
set to 1 received in one of the states listed below
Event : receipt by the BSC of a UA frame with the final bit set to 1 in one of the
following states:
a TEI is allocated
the multiframe mode is established
a multiframe mode time-out is running
Type : raw temporary
Source : recorded by the BSC
l
5608/3 Number of Abis Level 2 errors: UA received with PF 0
Name Q3 : abisLevel2ErrorRxUa0
Object : bts
Function : number of UA (Unnumbered Acknowledge) frames with the final bit
set to 0 received in one of the states listed below
Event : receipt by the BSC of a UA frame with the final bit set to 0 in one of the
following states:
a TEI is allocated
the multiframe mode is established
a multiframe mode time-out is running
waiting for establishment
waiting for clear
Type : raw temporary
Source : recorded by the BSC
l
5608/4 Number of Abis Level 2 errors: DM received with PF 0
Name Q3 : abisLevel2ErrorRxDm0
Object : bts
Function : number of DM (Disconnected Mode) frames with the final bit set to 0
received in one of the states listed below
Event : receipt by the BSC of a DM frame with the final bit set to 0 in one of
the following states:
the multiframe mode is established
a multiframe mode time-out is running
Type : raw temporary
Source : recorded by the BSC
l
5608/5 Number of Abis Level 2 errors: SABME received
Name Q3 : abisLevel2ErrorRxSabme
Object : bts
Function : number of SABME (Set in Asynchronous Balance Mode Extended)
frames received in one of the states listed below
Event : receipt by the BSC of a SABME frame in one of the following states:
the multiframe mode is established
a multiframe mode time-out is running
Type : raw temporary
Source : recorded by the BSC
l
5608/6 Number of Abis Level 2 errors: SABME retransmitted
Name Q3 : abisLevel2ErrorTxNSabme
Object : bts
Function : number of SABME frames unsuccessfully retransmitted N150 times
during an establishment period
Event : N150 unsuccessful retransmissions of an SABME frame during an
establishment period
Type : raw temporary
Source : recorded by the BSC
l
5608/7 Number of Abis Level 2 errors: DISC retransmitted
Name Q3 : abisLevel2ErrorTxNDisc
Object : bts
Function : number of DISC (Disconnect) frames unsuccessfully retransmitted
N150 times during a clearing period
Event : N150 unsuccessful retransmissions of a DISC frame during a clearing
period
Type : raw temporary
Source : recorded by the BSC
l
5608/8 Number of Abis Level 2 errors: I frame with PF 1 retransmitted
Name Q3 : abisLevel2ErrorReqOutState
Object : bts
Function : number of I frames with final bit set to 1 (state request) retransmitted
while a multiframe mode time-out is running
Event : receipt by the BSC of an I frame with final bit set to 1 (state request)
retransmitted while a multiframe mode time-out is running
Type : raw temporary
Source : recorded by the BSC
l
5608/9 Number of Abis Level 2 errors: Wrong NR received
Name Q3 : abisLevel2ErrorBadRxNr
Object : bts
Function : number of errored NR (Not Ready) frames received in one of the
states listed below
Event : receipt by the BSC of an errored NR frame in one of the following
states:
the multiframe mode is established
a multiframe mode time-out is running
Type : raw temporary
Source : recorded by the BSC
l
5608/10 Number of Abis Level 2 errors: FRMR received
Name Q3 : abisLevel2ErrorRxFrmr
Object : bts
Function : number of FRMR (frame reject) frames received in one of the states
listed below
Event : receipt by the BSC of an FRMR frame in one of the following states:
the multiframe mode is established
a multiframe mode time-out is running
Type : raw temporary
Source : recorded by the BSC
l
5608/11 Number of Abis Level 2 errors: Unknown frame
Name Q3 : abisLevel2ErrorRxNoImpl
Object : bts
Function : number of unknown frames with final bit set to 0 received in one of the
states listed below
Event : receipt by the BSC of an unknown frame with final bit set to 0 in one of
the following states:
a TEI is allocated
the multiframe mode is established
a multiframe mode time-out is running
waiting for establishment
waiting for clear
Type : raw temporary
Source : recorded by the BSC
l
5608/12 Number of Abis Level 2 errors: Wrong length
Name Q3 : abisLevel2ErrorBadLg
Object : bts
Function : number of wrong length frames received in one of the states listed
below
Event : receipt by the BSC of a wrong length frame in one of the following
states:
a TEI is allocated
the multiframe mode is established
a multiframe mode time-out is running
waiting for establishment
waiting for clear
Type : raw temporary
Source : recorded by the BSC
l
5609 Duration of Abis resource unavailability
Name Q3 : abisUnavailabilityTimeMoy
abisUnavailabilityTimeMax . . . . . . Maximum unavailability
duration
abisUnavailabilityTimeCum . . . . . Total unavailability duration
abisUnavailabilityTimeEch . . . . . . Number of samples
Object : bts
Function : average unavailability duration (= total duration divided by the
number of samples) and maximum unavailability duration of the RSL
LAPD links used by the cell TRX/DRXs, expressed in milliseconds
Event : LAPD link unavailability/availability, internal sampling time-out
elapse:
unavailability: start timer
availability: stop timer
sampling time-out elapse:
• read the instantaneous value of LAPD unavailability duration
• store its peak value
• add it to the total duration of LAPD unavailability in the
observation period
• step up by one the number of samples
Type : raw temporary
Source : recorded by the BSC
l
5610 Duration of Abis resource congestion
Name Q3 : abisCongestionTimeMoy
abisCongestionTimeMax . . . . . . . . Maximum congestion duration
abisCongestionTimeCum . . . . . . . . Total congestion duration
abisCongestionTimeEch . . . . . . . . Number of samples
Object : bts
Function : average congestion duration (= total duration divided by the number
of samples) and maximum congestion duration of the RSL LAPD
links used by the cell TRX/DRXs, expressed in milliseconds
Event : LAPD link congestion/non-congestion, internal sampling time-out
elapse:
congestion: start timer
non-congestion: stop timer
sampling time-out elapse:
• read the instantaneous value of LAPD congestion duration
• store its peak value
• add it to the total duration of LAPD congestion in the
observation period
• step up by one the number of samples
Type : raw temporary
Source : recorded by the BSC
5.6.1 Constants
The following named constants are defined for use in synthetic counters:
signif1bts (its value is 10)
signif1bsc (its value is 20)
This section contains counter definitions for synthetic BSS counters that have a
defined counter number at the OMC--R. In this section, counters are arranged in
numerical order.
l
8000 Global failure rate of outgoing handovers on TCH
Name Q3 : hoOutTchGlobalFailRate
hoOutTchGlobalFailRateV11
Object : bts
Function : global failure rate, in selection and execution, of outgoing intra-bss,
inter-bss, and intra-bts handovers on TCH in the cell
Formula :
successful outgoing intra handovers on TCH +
successful outgoing inter handovers on TCH +
successful intra-bts handovers on TCH
(1 - ---------------------------------------------)
handovers on TCH required (by cause)
*
greaterperc(hoReq, signif1bts)
=
(1067 + 1068 + 1083)
(1 - --------------------------------------)
∑(1138/i), i = each-possible-screening
*
greaterperc(∑(1138/i), 10)
l
8001 Global failure rate of outgoing handovers on SDCCH
Name Q3 : hoOutSdcchGlobalFailRate
hoOutSdcchGlobalFailRateV11
Object : bts
Function : global failure rate, in selection and execution, of outgoing intra-bss,
inter-bss, and intra-bts handovers required on SDCCH in the cell
Formula :
successful outgoing intra handovers on SDCCH +
successful outgoing inter handovers on SDCCH +
successful intra-bts handovers on SDCCH
(1 - ----------------------------------------------)
handovers on SDCCH required (by cause)
*
greaterperc(hoReqSdcch, signif1bts)
=
(1142 + 1143 + 1156)
(1 - ---------------------------------------)
∑(1139/i), i = each-possible-screening
*
greaterperc(∑(1139/i), 10)
Formula :
outgoing intra handovers on TCH requested +
outgoing inter handovers on TCH requested +
intra-bts handovers on TCH requested
(-------------------------------------------)
handovers on TCH required (by cause)
*
greaterperc(hoReq, signif1bts)
=
(1075 + 1076 + 1081)
(----------------------------------------)
∑(1138/i), i = each-possible-screening
*
greaterperc(∑(1138/i), 10)
=
(1150 + 1151 + 1154)
(-----------------------------------------)
∑(1139/i), i = each-possible-screening
*
greaterperc(∑(1139/i), 10)
l
8004 Selection failure rate of outgoing handovers on TCH
Name Q3 : hoOutTchSelectionFailRate
Object : bts
Function : selection failure rate of outgoing intra-bss, inter-bss, and intra-bts
handovers on TCH in the cell
Formula : V12
=
(1065 + 1066 + 1082)
(1 - ---------------------)
〈 1075 + 1076 + 1081)
*
greaterperc((1075 + 1076 + 1081), 10)
l
8005 Selection failure rate of outgoing handovers on SDCCH
Name Q3 : hoOutSdcchSelectionFailRate
Object : bts
Function : selection failure rate of outgoing intra-bss, inter-bss, and intra-bts
handovers on SDCCH in the cell
Formula : V12
=
(1140 + 1141 + 1155)
(1 - ---------------------)
1150 + 1151 + 1154
*
greaterperc((1150 + 1151 + 1154), 10)
=
(1067 + 1068 + 1083)
(1 - --------------------)
(1065 + 1066 + 1082)
*
greaterperc((1065 + 1066 + 1082), 10)
=
(1142 + 1143 + 1156)
(1 - --------------------)
(1140 + 1141 + 1155)
*
greaterperc((1140 + 1141 + 1155), 10)
l
8008 Selection failure rate of incoming handovers on TCH
Name Q3 : hoInTchSelectionFailRate
Object : bts
Function : selection failure rate of incoming intra- and inter-bss handovers on
TCH in the cell
Formula :
incoming intra handovers on TCH executed +
incoming inter handovers on TCH executed
(1 - -------------------------------------------)
incoming intra handovers on TCH requested +
incoming inter handovers on TCH requested
*
greaterperc(hoRequestIncoming, signif1bts)
=
(1071 + 1072)
(1 - -------------)
(1069 + 1070)
*
greaterperc((1069 + 1070), 10)
l
8009 Selection failure rate of incoming handovers on SDCCH
Name Q3 : hoInSdcchSelectionFailRate
Object : bts
Function : selection failure rate of incoming intra- and inter-bss handovers on
SDCCH in the cell
Formula :
incoming intra handovers on SDCCH executed +
incoming inter handovers on SDCCH executed
(1 - ---------------------------------------------)
incoming intra handovers on SDCCH requested +
incoming inter handovers on SDCCH requested
*
greaterperc(hoExecutionIncomingSdcch, signif1bts)
=
(1146 + 1047)
(1 - -------------)
(1144 + 1145)
*
greaterperc((1144 + 1145), 10)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
l
8010 Execution failure rate of incoming handovers on TCH
Name Q3 : hoInTchExecutionFailRate
Object : bts
Function : execution failure rate of incoming intra- and inter-bss handovers on
TCH in the cell
Formula :
successful incoming intra handovers on TCH +
successful incoming inter handovers on TCH
(1 - --------------------------------------------)
incoming intra handovers on TCH executed +
incoming inter handovers on TCH executed
*
greaterperc(hoExecutionIncoming, signif1bts)
=
(1073 + 1074)
(1 - -------------) * greaterperc((1071 + 1072), 10)
(1071 + 1072)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
l
8011 Execution failure rate of incoming handovers on SDCCH
Name Q3 : hoInSdcchExecutionFailRate
Object : bts
Function : execution failure rate of incoming intra- and inter-bss handovers on
SDCCH in the cell
Formula :
successful incoming intra handovers on SDCCH +
successful incoming inter handovers on SDCCH
(1 - ----------------------------------------------)
incoming intra handovers on SDCCH executed +
incoming inter handovers on SDCCH executed
*
greaterperc(hoSuccessIncomingSdcch, signif1bts)
=
(1148 + 1149)
(1 - -------------) * greaterperc((1146 + 1147), 10)
(1146 + 1147)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
l
8012 Ratio of successful outgoing handovers on TCH after first
attempt
Name Q3 : hoOutTchFirstAttemptSuccessRatio
Object : bts
Function : ratio of successful outgoing intra- and inter-bss handovers to the first
cell in the list of eligible cells to successful outgoing handovers on
TCH in the cell
Formula :
successful outgoing (intra + inter)
handovers on TCH after first attempt
(-----------------------------------------------------)
successful outgoing (intra + inter) handovers on TCH
*
greaterperc(hoSuccessOutgoingIntraBss
+hoSuccessOutgoingInterBss, signif1bts)
(1077 + 1078)
= (-------------) * greaterperc((1067 + 1068), 10)
(1067 + 1068)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
l
8013 Ratio of successful outgoing handovers on SDCCH after first
attempt
Name Q3 : hoOutSdcchFirstAttemptSuccessRatio
Object : bts
Function : ratio of successful outgoing intra- and inter-bss handovers to the first
cell in the list of eligible cells to successful outgoing handovers on
SDCCH in the cell
Formula :
successful outgoing (intra + inter)
handovers on SDCCH after first attempt
(-------------------------------------------------------)
successful outgoing (intra + inter) handovers on SDCCH
*
greaterperc(hoSuccessOutgoingIntraBssSdcch
+hoSuccessOutgoingInterBssSdcch, signif1bts)
(1152 + 1153)
(-------------) * greaterperc((1142 + 1143), 10)
(1142 + 1143)
l
8016 Total number of establishment indications received for call
initialization
Name Q3 : AllEstabIndicSignalling
Object : bts
Function : number of establishment indications received for call initialization
Formula :
IMMEDIATE ASSIGNMENT messages transmitted on SDCCH
= [∑(1193/i)], i = each-possible-screening
l
8017 Number of t3107 time-out elapse: Changing from SDCCH to
TCH or preempted PDTCH
Name Q3 : t3107ExpAssign
Object : bts
Function : number of mobiles lost during a change from SDCCH to TCH or
preempted PDTCH because of T3107 time-out elapse
Formula :
TCH/FR or preempted PDTCH assignment requests -
TCH/FR successfully assigned -
ASSIGN FAILURE messages received -
intra-bts handovers on TCH executed +
successful intra-bts handovers on TCH +
unsuccessful intra-bts handovers on TCH with
reestablishment in the serving cell
= 1049 - (1050 + 1055)- (1082 - (1083 + 1134))
l
8019 Number of t3107 time-out elapse: Intra-bts handover on TCH
Name Q3 : t3107ExpIntraBtsHoTch
Object : bts
Function : number of mobiles lost during intra-bts handovers on TCH because of
T3107 time-out elapse
Formula :
intra-bts handovers on TCH executed -
successful intra-bts handovers on TCH -
unsuccessful intra-bts handovers on TCH
l
8021 Number of t3103 time-out elapse: Handover on SDCCH
Name Q3 : t3103ExpSdcch
Object : bts
Function : number of mobiles lost during a handover on SDCCH because of
T3103 time-out elapse. This counter also tallies - for rare cases-- the
receipt of CLEAR COMMAND during an inter-bss handover with a
cause different from “handover successful” or “call control”
Formula :
outgoing intra handovers on SDCCH executed -
successful outgoing intra handovers on SDCCH -
unsuccessful outgoing intra handovers on SDCCH
+
outgoing inter handovers on SDCCH executed -
successful outgoing inter handovers on SDCCH -
unsuccessful outgoing inter handovers on SDCCH
8037 Total TCH seizure attempts (not including handovers) at cell level
Name Q3 : attemptedTchFrSeizureNotInclHo
Object : bts
Function : number of TCH seizure attempts not including handovers = Mobile
originating call attempt(s) + Mobile terminating call attempt(s) +
Re--establishment attempt(s) + Directed Retry attempt(s)
Formula : (1609/0 + 1609/1 + 1613) - (1069 + 1070 + 1081)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V11 counter
In V12, 1841/0 counter is more accurate.
l
8050 Ratio of maximum Downlink power use on TCHs
Name Q3 : relativeTimeDLPowerCtrlMaxTch
Object : bts
Function : ratio of maximum Downlink power use duration on busy TCHs to
TCH connection duration in the cell
Formula :
duration of maximum Downlink power use on busy TCHs
---------------------------------------------------
connection duration of TCHs
1198Cum
= -------
1600Cum
with 1600Cum = ∑(1600) on all transceiverZones
l
8051 Ratio of maximum Uplink power use on TCHs
Name Q3 : relativeTimeULPowerCtrlMaxTch
Object : bts
Function : ratio of maximum Uplink power use duration on busy TCHs to TCH
connection duration in the cell
Formula :
duration of maximum Uplink power use on busy TCHs
-------------------------------------------------
connection duration of TCHs
1199Cum
= -------
1600Cum
with 1600Cum = ∑(1600) on all transceiverZones
l
8052 Ratio of maximum Downlink power use on SDCCHs
Name Q3 : relativeTimeDLPowerCtrlMaxSdcch
Object : bts
Function : ratio of maximum Downlink power use duration on busy SDCCHs to
SDCCH connection durations in the cell
Formula :
duration of maximum Downlink power use on busy SDCCHs
-----------------------------------------------------
connection duration of SDCCHs
1601Cum
= -------
1603Cum
with 1603Cum = ∑(1603) on all transceiverZones
l
8053 Ratio of maximum Uplink power use on SDCCHs
Name Q3 : relativeTimeULPowerCtrlMaxSdcch
Object : bts
Function : ratio of maximum Uplink power use duration on busy SDCCHs to
SDCCH connection durations in the cell
Formula :
duration of maximum Uplink power use on busy SDCCHs
---------------------------------------------------
connection duration of all SDCCHs
1602Cum
= -------
1603Cum
with 1603Cum = ∑(1603) on all transceiverZones
l
8104 Ratio of number of requested handovers by dualband MSs to
second frequency band to the number of requested handover for
dualband MS to main frequency band
Name Q3 : requestedHandoverForDualBandMSToSecondVersusMainBand
Object : bts
Function : ratio of number of requested handovers by dualband MSs to second
frequency band to the number of requested handover by dualband
MSs to main frequency band
Formula :
outgoing handovers requested by dualband MSs from
main to second frequency band +
outgoing handovers requested by dualband MSs from
second to same frequency band
---------------------------------------------------
outgoing handovers requested by dualband MSs from
main to same frequency band +
outgoing handovers requested by dualband MSs from
second to main frequency band
1208 + 1784
= ------------
1783 + 1785
Formula :
immediate assignments for dualband MS
--------------------------------------
ESTABLISH INDICATION messages in
establishment phase received (by cause)
=
1207
--------------------------------------
∑(1193/i), i = each-possible-screening
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8110 Failure rate of cell tiering from large pattern to small pattern
Name Q3 : hoIntraBtsFailRateTchTieringLargeToSmallPattern
Object : bts
Function : failure rate in selection and execution of intra--bts handovers in the
cell for cell tiering from large pattern to small pattern
Formula :
1802/0
1 - -----------
1138/15
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Feature : Cell Tiering (TF995 - V12)
Note : V12 counter
l
8111 Failure rate of cell tiering from small pattern to large pattern
Name Q3 : hoIntraBtsFailRateTchTieringSmallToLargePattern
Object : bts
Function : failure rate in selection and execution of intra--bts handovers in the
cell for cell tiering from small pattern to large pattern
Formula :
1802/1
1 - -----------
1138/16
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
l
8502 Maximum ratio of outgoing handover requests on TCH
Name Q3 : hoOutTchRequestMaxRatio
hoOutTchRequestMaxRatioV11
Object : bsc
Function : maximum ratio of outgoing intra-bss, inter-bss, and intra-bts
handover requests to handovers on TCH required in the BSS
Formula :
max_cell(ratio of outgoing handover requests on TCH)
= max_cell(8002)
l
8504 Maximum selection failure rate of outgoing handovers on TCH
Name Q3 : hoOutTchSelectionFailMaxRate
Object : bsc
Function : maximum selection failure rate of outgoing intra-bss, inter-bss, and
intra-bts handovers on TCH in the BSS
Formula :
max_cell(selection failure rate of
outgoing handovers on TCH)
= max_cell(8004)
l
8506 Maximum execution failure rate of outgoing handovers on TCH
Name Q3 : hoOutTchExecutionFailMaxRate
Object : bsc
Function : maximum execution failure rate of outgoing intra-bss, inter-bss, and
intra-bts handovers on TCH in the BSS
Formula :
max_cell(execution failure rate of
outgoing handovers on TCH)
= max_cell(8006)
l
8508 Maximum selection failure rate of incoming handovers on TCH
Name Q3 : hoInTchSelectionFailMaxRate
Object : bsc
Function : maximum selection failure rate of incoming intra- and inter-bss
handovers on TCH in the BSS
Formula :
max_cell(selection failure rate of
incoming handovers on TCH)
= max_cell(8008)
l
8510 Maximum execution failure rate of incoming handovers on TCH
Name Q3 : hoInTchExecutionFailMaxRate
Object : bsc
Function : maximum execution failure rate of incoming intra- and inter-bss
handovers on TCH in the BSS
Formula :
max_cell(execution failure rate of
incoming handovers on TCH)
= max_cell(8010)
l
8512 Minimum ratio of successful outgoing handovers on TCH after
first attempt
Name Q3 : hoOutTchFirstAttemptSuccessMinRatio
Object : bsc
Function : minimum ratio of successful outgoing intra- and inter-bss handovers
after first attempt on TCH in the BSS
Formula :
min_cell(ratio of successful outgoing
handovers on TCH after first attempt)
= min_cell(8012)
l
8550 BSC global failure rate of outgoing handovers on TCH
Name Q3 : hoOutTchBscGlobalFailRate
hoOutTchBscGlobalFailRateV11
Object : bsc
Function : global failure rate, in selection and execution, of outgoing intra-bss,
inter-bss, and intra-bts handovers on TCH in the BSS
Formula :
sum_cell (successful outgoing
intra + inter + intra-bts
handovers on TCH)
(1 - ----------------------------------------------)
sum_cell(handovers on TCH required (by cause))
*
greaterperc(sum(hoReq), signif1bsc)
=
sum_cell(1067 + 1068 + 1083)
(1 - -------------------------------------------------)
sum_cell(∑(1138/i)), i = each-possible-screening
*
greaterperc(sum_cell(∑(1138/i)), 20)
Formula :
sum_cell (successful outgoing
intra + inter + intra-bts
handovers on SDCCH)
(1 - ------------------------------------------------)
sum_cell(handovers on SDCCH required (by cause))
*
greaterperc(sum(hoReqSdcch), signif1bsc)
=
sum_cell(1142 + 1143 +1156)
(1 - -------------------------------------------------)
sum_cell(∑(1139/i)), i = each-possible-screening
*
greaterperc(sum_cell(∑(1139/i), 20)
l
8552 BSC ratio of outgoing handover requests on TCH
Name Q3 : hoOutTchRequestBscRatio
hoOutTchRequestBscRatioV11
Object : bsc
Function : ratio of outgoing intra-bss, inter-bss, and intra-bts handovers
requested to handovers on TCH required in the BSS
Formula :
sum_cell
(outgoing intra handovers on TCH requested +
outgoing inter handovers on TCH requested +
intra-bts handovers on TCH requested)
(-----------------------------------------------)
sum_cell(handovers on TCH required (by cause))
*
greaterperc(sum(hoReq), signif1bsc)
=
sum_cell(1075 + 1076 + 1081)
(------------------------------------------------)
sum_cell(∑(1138/i)), i = each-possible-screening
*
greaterperc(sum_cell(∑(1138/i), 20)
l
8553 BSC ratio of outgoing handover requests on SDCCH
Name Q3 : hoOutSdcchRequestBscRatio
hoOutSdcchRequestBscRatioV11
Object : bsc
Function : ratio of outgoing intra-bss, inter-bss, and intra-bts handovers
requested to handovers on SDCCH in the BSS
Formula :
sum_cell
(outgoing intra handovers on SDCCH requested +
outgoing inter handovers on SDCCH requested +
intra-bts handovers on SDCCH requested)
(--------------------------------------------------)
sum_cell(handovers on SDCCH required (by cause))
*
greaterperc(sum(hoReqSdcch), signif1bsc)
=
sum_cell(1150 + 1151 + 1154)
(--------------------------------------------------)
sum_cell(∑(1139/i)), i = each-possible-screening
*
greaterperc(sum_cell(∑(1139/i)), 20)
l
8554 BSC selection failure rate of outgoing handovers on TCH
Name Q3 : hoOutTchSelectionBscFailRate
Object : bsc
Function : selection failure rate of outgoing intra-bss, inter-bss, and intra-bts
handovers on TCH in the BSS
Formula : V12
=
sum_cell(1065 + 1066 + 1082)
(1 - -------------------------------)
sum_cell (1075 + 1076 + 1081)
*
greaterperc(sum_cell (1075 + 1076 + 1081), 20)
Formula : V12
=
sum_cell(1140 + 1141 + 1155)
(1 - -----------------------------)
sum_cell(1150 + 1151 + 1154)
*
greaterperc(sum_cell(1150 + 1151 + 1154), 20)
=
sum_cell(1067 +1068 +1083)
(1 - --------------------------)
sum_cell(1065 +1066 +1082)
*
greaterperc(sum_cell(1065 +1066 +1082), 20)
=
sum_cell(1142 + 1143 + 1156)
(1 - ----------------------------)
sum_cell(1140 + 1141 + 1155)
*
greaterperc(sum_cell(1140 + 1141 + 1155), 20)
l
8558 BSC selection failure rate of incoming inter handovers on TCH
Name Q3 : hoInInterTchSelectionBscFailRate
Object : bsc
Function : selection failure rate of incoming inter-bss handovers on TCH in the
BSS
Formula :
sum_cell(incoming inter-bss HOs on TCH executed)
(1 - -------------------------------------------------)
sum_cell(incoming inter-bss HOs on TCH requested)
*
greaterperc(sum(hoRequestIncomingInterBss), signif1bsc)
=
sum_cell(1072)
(1 - --------------)
sum_cell(1070)
*
greaterperc(sum_cell(1070), 20)
l
8560 BSC execution failure rate of incoming inter handovers on TCH
Name Q3 : hoInInterTchExecutionBscFailRate
Object : bsc
Function : execution failure rate of incoming inter-bss handovers on TCH in the
BSS
Formula :
sum_cell(successful incoming inter-bss HOs on TCH)
(1 - -------------------------------------------------)
sum_cell(incoming inter-bss HOs on TCH executed)
*
greaterperc(sum(hoExecutionIncomingInterBss), signif1bsc)
=
sum_cell(1074)
(1 - --------------) * greaterperc(sum_cell(1072), 20)
sum_cell(1072)
=
sum_cell(1149)
(1 - --------------) * greaterperc(sum_cell(1147), 20)
sum_cell(1147)
l
8562 BSC execution failure rate of incoming intra handovers on TCH
Name Q3 : hoInIntraTchExecutionBscFailRate
Object : bsc
Function : execution failure rate of incoming intra-bss handovers on TCH in the
BSS
Formula :
sum_cell(successful incoming intra-bss HOs on TCH)
(1 - --------------------------------------------------)
sum_cell(incoming intra-bss HOs on TCH executed)
*
greaterperc(sum(hoExecutionIncomingIntraBss), signif1bsc)
=
sum_cell(1073)
(1 - --------------) * greaterperc(sum_cell(1071), 20)
sum_cell(1071)
=
sum_cell(1148)
(1 - --------------) * greaterperc(sum_cell(1146), 20)
sum_cell(1146)
l
8564 BSC execution failure rate of outgoing inter handovers on TCH
Name Q3 : hoOutInterTchExecutionBscFailRate
Object : bsc
Function : execution failure rate of outgoing inter-bss handovers on TCH in the
BSS
Formula :
sum_cell(successful outgoing inter-bss HOs on TCH)
(1 - --------------------------------------------------)
sum_cell(outgoing inter-bss HOs on TCH executed)
*
greaterperc(sum(hoExecutionOutgoingInterBss), signif1bsc)
=
sum_cell(1068)
(1 - --------------) * greaterperc(sum_cell(1066), 20)
sum_cell(1066)
=
sum_cell(1143)
(1 - --------------) * greaterperc(sum_cell(1141), 20)
sum_cell(1141)
l
8566 BSC ratio of successful outgoing handovers on TCH after first
attempt
Name Q3 : hoOutFirstSuccessTchRatio
Object : bsc
Function : ratio of successful outgoing intra- and inter-bss handovers after first
attempt to successful handovers on TCH in the BSS
Formula :
sum_cell (successful outgoing (intra + inter)
handovers on TCH after first attempt)
(-----------------------------------------------)
sum_cell (successful outgoing (intra + inter)
handovers on TCH)
*
greaterperc(sum(hoSuccessOutgoingIntraBss)
+sum(hoSuccessOutgoingInterBss), signif1bsc)
=
sum_cell(1077 + 1078)
(--------------------)
sum_cell(1067 + 1068)
*
greaterperc(sum_cell(1067 + 1068), 20)
l
8567 BSC ratio of successful outgoing handovers on SDCCH after first
attempt
Name Q3 : hoOutFirstSuccessSdcchRatio
Object : bsc
Function : ratio of successful outgoing intra- and inter-bss handovers after first
attempt to successful handovers on SDCCH in the BSS
Formula :
sum_cell (successful outgoing (intra + inter)
handovers on SDCCH after first attempt)
(--------------------------------------------------)
sum_cell (successful outgoing (intra + inter)
handovers on SDCCH)
*
greaterperc(sum(hoSuccessOutgoingIntraBssSdcch)
+sum(hoSuccessOutgoingInterBssSdcch), signif1bsc)
=
sum_cell(1152 + 1153)
(---------------------)
sum_cell(1142 + 1143)
*
greaterperc(sum_cell(1142 + 1143), 20)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
l
8568 Rate of erroneous messages on the A interface
Name Q3 : aMessageErroneousRate
Object : bsc
Function : rate of erroneous messages on the A interface (applicative level)
Formula :
number of erroneous BSSAP messages received
----------------------------------------------
number of erroneous BSSAP messages received +
number of BSSAP messages received
=
1109
-------------
(1109 + 1107)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V11-- counter
l
8569 Ratio of SCCP failure
Name Q3 : sccpResourceFailureRatio
Object : bsc
Function : ratio of the number of SCCP connection refusals (by BSC or MSC) to
the number of SCCP connections allocated (refer to the following
formula)
Formula :
sccpResourceFailureRatio bsc
=
((sccpRessourceFailure+sccpRessourceFailureBscRefusal) /
(sccpAllocated+sccpRessourceFailure+sccpRessourceFailure
BscRefusal))
*
greaterperc (sccpAllocated+sccpRessourceFailure+sccp
RessourceFailureBscRefusal,signif1bsc)
1106/0 + 1106/1
= (-----------------------)
1104/0 + 1106/0 + 1106/1
*
greaterperc((1104/0 + 1106/0 + 1106/1), 20)
l
8601 Average number of TCH/FR used in the BSS because of SDCCH
unavailability
Name Q3 : bscTchFrAveragedUsedOverflowAllocationMoy
Object : bsc
Function : average number of TCH/FR allocated because of SDCCH
unavailability in all cells controlled by the BSC
Formula :
sum_cell(average number of TCH/FR used)
= sum_cell(1611/2)
with 1611/2= ∑(1611/2) on all transceiverZones
l
8602 Average number of TCH/FR used in the BSS for call
reestablishments
Name Q3 : TchFrAveragedUsedPrimoAllocation
Object : bsc
Function : average number of TCH/FR allocated for call reestablishments in all
cells controlled by the BSC
Formula :
sum_cell(average number of TCH/FR used)
= sum_cell(1611/1)
with 1611/1 = ∑(1611/1) on all transceiverZones
l
8605 Number of signaling channels allocated in the BSS for access
other than paging
Name Q3 : bscOtherThanPaging
Object : bsc
Function : number of signalling channel allocation requests with cause different
from “reply to paging request” in all cells controlled by the BSC
Formula :
sum_cell
(number of signalling channel requests for non
urgent calls = other services + call
reestablishments + urgent calls))
= sum_cell (1191/0 + 1191/2 + 1191/3 + 1191/5 + 1191/6
+ 1191/7)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V11-- counter
l
8606 Number of outgoing handovers on TCH executed in the BSS
Name Q3 : hoOutExecutionBscTch
Object : bsc
Function : number of attempts to execute outgoing intra- and inter-bss handovers
on TCH in all cells controlled by the BSC
Formula :
sum_cell
(outgoing intra handovers on TCH executed +
outgoing inter handovers on TCH executed +
intra-bts handovers on TCH executed)
Formula :
sum_cell
(outgoing intra handovers on SDCCH executed +
outgoing inter handovers on SDCCH executed +
intra-bts handovers on SDCCH executed)
= sum_cell(1071 + 1072)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V11-- counter
l
8609 Number of incoming handovers on SDCCH executed in the BSS
Name Q3 : hoInExecutionBscSdcch
Object : bsc
Function : number of attempts to execute incoming intra- and inter-bss
handovers on SDCCH in all cells controlled by the BSC
Formula :
sum_cell
(incoming intra handovers on SDCCH executed
incoming inter handovers on SDCCH executed)
= sum_cell(1146 + 1147)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V11-- counter
l
8610 Total number of SDCCHs allocated in the BSS
Name Q3 : bscSdcchAllocated
Object : bsc
Function : total number of SDCCH allocations in the BSS
Formula :
sum_cell(number of SDCCHs allocated)
= sum_cell(1606)
with 1606 = ∑(1606) on all transceiverZones
Formula :
sum_cell(number of TCH/FR allocated)
for call reestablishments
= sum_cell(1609/1)
with 1609/1 = ∑(1609/1) on all transceiverZones
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V11-- counter
l
8613 Total number of TCH/FR allocated in the BSS for traffic
Name Q3 : bscTchFrAllocatedTchAllocation
Object : bsc
Function : total number of TCH allocations for traffic in all cells controlled by
the BSC
Formula :
sum_cell(number of TCH/FR allocated) for traffic
= sum_cell(1609/0)
with 1609/0 = ∑(1609/0) on all transceiverZones
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V11-- counter
l
8623 Average downlink RxLev in dBm
Name Q3 : averageDLRxLev
Object : bts
Function : average downlink RxLev for the cell, in dBm
Formula :
1623/0/Cum/Cell
------------------------------------------------- - 110
1600/0/Cum/Cell/480 + 1603/0/Cum/Cell/470 - 1622/0/Cum/Cell
= -110 +(rxLevDownlink /
(connectionDurationTchCum / 480
+ connectionDurationSdcchCum / 470
- msLostMeasurements) )
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V11-- counter
l
8624 Average uplink RxLev in dBm
Name Q3 : averageULRxLev
Object : bts
Function : average uplink RxLev for the cell, in dBm
Formula :
1624/0/Cum/Cell
----------------------------------------------- - 110
1600/0/Cum/Cell/480 + 1603/0/Cum/Cell/470
= -110 + (rxLevUplink /
(connectionDurationTchCum / 480
+ connectionDurationSdcchCum / 470) )
l
8626 Average uplink RxQual in BER
Name Q3 : averageULRxQual
Object : bts
Function : average uplink RxQual for the cell, in BER
Formula :
1626/0/Cum/Cell
----------------------------------------------- / 110
1600/0/Cum/Cell/480 + 1603/0/Cum/Cell/470
=
1718 + 1719
(------------) * greaterperc(1717, 10000)
1717
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8629 Correction rate of downlink Abis TRAU frame
Name Q3 : pcmErrCorrEfficiency
Object : bts
Function : ratio of the number of downlink Abis TRAU frames corrected to the
number of downlink Abis TRAU frames received
Formula :
1718
--------
1717
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8637 Total TCH seizure attempts (not including handovers) at BSC
level
Name Q3 : bscAttemptedTchFrSeizureNotInclHo
Object : bsc
Function : number of TCH seizure attempts not including handovers
Formula : Σ 1841/0
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8639 Total TCH seizure attempts (including handovers) at bsc level
Name Q3 : bscAttemptedTchFrSeizureInclHo
Object : bsc
Function : number of TCH seizure attempts including handovers
Formula : Σ 8039
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8640 TCH allocation failures at bsc level
Name Q3 : bscAllocationFailureTchFrSeizureInclHo
Object : bsc
Function : number of TCH allocation failures including handovers
Formula : Σ 8040
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8644 G14 consolidated at bsc level
Name Q3 : bscClearRequestTraffic
Object : bsc
Function : number of calls dropped by a CLEAR_REQUEST after TCH
assignment completed
Formula : Σ 8044
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8700 PCM unavailability in the BSS in seconds
Name Q3 : pcminsecondsMoy
pcminsecondsMax
pcminsecondsCum
pcminsecondsEch
Object : bsc
Function : PCM unavailability in the BSS, expressed in seconds
Formula :
average time of PCM availability
--------------------------------
1000
Formula :
average duration to allocate all TCH/FR resources
and PDTCH resources configured as preemptable
-------------------------------------------------
1000
l
8706 Ratio of SDCCH resource failures in the cell
Name Q3 : cellSdcchResourceFailureRatio
Object : bts
Function : ratio of the number of SDCCH allocation failures in the cell to the
number of SDCCH allocation attempts
Formula :
C1608
(---------------------) * greaterperc(1606, 20)
1606 + 1608 + 1609/2
l
8707 Ratio of TCH resource failures in the cell
Name Q3 : cellTchResourceFailureRatio
Object : bts
Function : ratio of the number of TCH allocation failures in the cell to the number
of TCH or preempted PDTCH allocation attempts
Formula :
1613 + 1163/30
(--------------------------------) * greaterperc(1609/0, 20)
1613 + 1163/30 + 1609/0 + 1609/1 + 1609/2 + 1609/3
l
8713 Ratio of the number of communications abnormally released in
signalling phase in the cell
Name Q3 : signallingReleaseRatio
Object : bts
Function : ratio of the number true communications released in signalling phase
in the cell, except release by standard CLEAR_COMMAND or on
phantom requests, to the number of communications established in a
signalling channel (initial call establishment or successful incoming
handover on SDCCH)
Formula :
∑(1163/i), i for each possible cause (i#5,6,20)
(-----------------------------------------------)
1195 + 1196
*
greaterperc(estabIndicSig, 20)
1778 - 1163/6
= (---------------) * greaterperc((1195 + 1196), 20)
1195 + 1196
Formula :
∑(1164/i), i for each possible cause
(--------------------------------------)
1050 - 1083 + 1073 + 1074
*
greaterperc(successfulTchFrSeizures, 20)
1779
= (--------------------------)
1050 - 1083 + 1073 + 1074
*
greaterperc(1050, 20)
l
8726 Number of decoded random accesses received by the BTS from
the MS for all the cells
Name Q3 : rachBusyCountCell
Object : bts
Function : sum for each CCCH occurrence of decoded random accesses received
by the BTS from the MS
Formula :
∑(1026), for each CCCH occurence
=rachBusyCount + rachBusyCount2
+ rachBusyCount4 + rachBusyCount6
l
8727 Number of random accesses transmitted to the BSC for all the
cells
Name Q3 : rachAccessCountCell
Object : bts
Function : sum for each CCH occurrence of transmitted random accesses
Formula :
∑(1027), for each CCCH occurrence
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8728 Number of paging requests immediately served for all the cells
Name Q3 : pchNoWaitCell
Object : bts
Function : sum for each CCCH occurrence of immediately served pagings
Formula :
∑(1028), for each CCCH occurrence
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8729 Number of paging requests served after one wait for all the cells
Name Q3 : pchOneWaitCell
Object : bts
Function : sum for each CCCH occurrence of served pagings after one wait
Formula :
∑(1029), for each CCCH occurrence
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8730 Number of paging requests served after two waits for all the cells
Name Q3 : pchTwoWaitCell
Object : bts
Function : sum for each CCCH occurrence of served pagings after two waits
Formula :
∑(1030), for each CCCH occurence
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8731 Number of paging requests served after more than two waits for
all the cells
Name Q3 : pchMoreWaitCell
Object : bts
Function : sum for each CCCH occurrence of served pagings after more than two
waits
Formula :
∑(1031), for each CCCH occurence
Formula :
∑(1604cum)/ ∑(1604ech), for each CCCH occurence
= MAX (1604max), for each CCCH occurrence
l
8735 Number of pagings discarded in the PAGCH queue for all the
cells
Name Q3 : pchQueuePagesDiscardedCell
Object : bts
Function : sum for each CCCH occurrence of discarded pagings
Formula :
∑(1605), for each CCCH occurrence
l
8757 Ratio of TCH or preempted PDTCH resource failures in the
TDMA class
Note : This counter is not implemented on the OMC--R.
Name Q3 : tdmaClassTchResourceFailureRatio
Object : transceiverZone
Function : ratio of the number of TCH or preempted PDTCH allocation failures
in the TDMA class
Formula :
1613
----------------------
1613 + 1609/0 + 1609/1
l
8760 Ratio between BIFP0 load and BIFP load average
Note : This counter is not implemented on the OMC--R.
Name Q3 : cpue0LoadRatio
Object : bts
Function : ratio between BIFP0 load and BIFP load average
Formula :
1835Moy (cpue0)
------------------------------------
1835Moy (cpue0) + 1835Moy (cpue1)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
l
8761 Ratio between BIFP1 load and BIFP load average
Note : This counter is not implemented on the OMC--R.
Name Q3 : cpue1LoadRatio
Object : bts
Function : ratio between BIFP1 load and BIFP load average
Formula :
1835Moy (cpue1)
------------------------------------
1835Moy (cpue0) + 1835Moy (cpue1)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
8803 AlltchFrAllocated
Name Q3 : tchOccupancy
Object : bts
Function : ratio of average number of tch used to the average of tch available
Formula :
AlltchFrAveragedUsedMoy
------------------------------------
tchFrAveragedAvailableMoy
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
*
greaterperc(attemptedTchFrSeizures,tchFrAveragedAvailableMoy)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
9504 : hoExecutionOutgoing
Name Q3 : hoExecutionOutgoing
Object : bts
Function : number of attempts to execute outgoing intra and inter--bss handovers
on TCH in all cells controlled by the BSC
Formula : hoExecutionOutgoingIntraBss
+ hoExecutionOutgoingInterBss
+ hoExecutionIntraBts
= 1065/0 + 1066/0 + 1082/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
9505 : hoExecutionOutgoingSdcch
Name Q3 : hoExecutionOutgoingSdcch
Object : bts
Function : Total number of outgoing handovers on TCH executed in the BSS on
SDCCH
Formula : hoExecutionOutgoingIntraBssSdcch
+ hoExecutionOutgoingInterBssSdcch
+ hoExecutionIntraBtsSdcch
= 1140/0 + 1141/0 + 1155/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
9506 : hoExecutionIncoming
Name Q3 : hoExecutionIncoming
Object : bts
Function : number of attempts to execute incoming intra-- and inter--bss
handovers on TCH in all cells controlled by the BSC
Formula : (1 -- (hoExecutionIncoming / hoRequestIncoming))
* greaterperc(hoRequestIncoming, signif1bts)
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
9507 : hoExecutionIncomingSdcch
Name Q3 : hoExecutionIncomingSdcch
Object : bts
Function : number of attempts to execute incoming intra-- and inter--bss
handovers on SDCCH in all cells controlled by the BSC
Formula : hoExecutionIncomingIntraBssSdcch
+ hoExecutionIncomingInterBssSdcch
= 1146/0 + 1147/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Formula :
sum (tchFrAveragedUsedMoy)
------------------------------------
sum (tchFrAveragedAvailableTrZoneMoy)
Type : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : V12 counter
Name Q3 : AllrachNonDecodedAvLevelCum/Ech
Object : bts
Function : Average level of non--decoded RACH access summed over all time
slots
Formula : rachNonDecodedAvLevelCum
+ rachNonDecodedAvLevelTs2Cum
+ rachNonDecodedAvLevelTs4Cum
+ rachNonDecodedAvLevelTs6Cum;
= sum(1033/0)
where the sum is calculated over all time slots (CUM only)
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : AlltchFrAllocated
Object : bts
Function : Number of TCH/FR or preempted PDTCH allocated for traffic in the
zone (concentric cell)
Formula : tchFrAllocatedTchAllocation
+ tchFrAllocatedPrimoAllocation
+ tchFrAllocatedOverflowAllocation
+ tchFrAllocatedWps
= 1609/0 + 1609/1 + 1609/2 + 1609/3
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : AlltchFrAveragedUsedMoy
Object : bts
Function : Average number of TCH/FR or pre--empted PDTCH used for traffic
in the zone (concentric cell)
Formula : tchFrAveragedUsedTchAllocationMoy
+ tchFrAveragedUsedPrimoAllocationMoy
+ tchFrAveragedUsedOverflowAllocationMoy
= 1611/0 + 1611/1 + 1611/2
(MOY values only)
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : connectionDurationCum
Object : bts
Function : Cumulative connection duration as derived from the total duration of
TCH/FR (or pre--empted PDTCH) and SDCCH
Formula : (connectionDurationTchCum / 480 - 1)
+ (connectionDurationSdcchCum / 470 -- 1)
1600/0 1603/0
= (-- - - - - - - - 1) + (-- - - - - - - - 1)
480 470
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Note : The value provided by this counter is expressed as a number of 480 ms
(or 470 ms) periods.
Name Q3 : estabIndicSig
Object : bts
Function : Number of ESTABLISH INDICATION messages in establishment
phase received (both phase 1 and phase 2)
Formula : estabIndicSigPhase1 + estabIndicSigPhase2
= 1195/0 + 1196/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : failedTchFrSeizures
Object : bts
Function : Ratio of the number unsuccessful TCH/FR seizures to the number of
all TCH/FR seizures attempted
Formula : 1 -- (successfulTchFrSeizures
/ attemptedTchFrSeizures)
1716/0
= 1 - -------
1049/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoReq
Object : bts
Function : Total number of handovers on TCH required: all causes
Formula : hoRequiredTchUplinkStrength
+ hoRequiredTchDownlinkStrength
+ hoRequiredTchUplinkQuality
+ hoRequiredTchDownlinkQuality
+ hoRequiredTchDistance
+ hoRequiredTchPowerBudgetQuality
+ hoRequiredTchCapture
+ hoRequiredTchIntraBtsOm
+ hoRequiredTchIntraBtsUplink
+ hoRequiredTchIntraBtsDownlink
+ hoRequiredTchDirectedRetry
+ hoRequiredTchTdmaClass0
+ hoRequiredTchTdmaClass1
+ hoRequiredTchInterBtsOm
+ hoRequiredTchTraffic
+ hoRequiredTchTieringLargeToSmallPattern
+ hoRequiredTchTieringSmallToLargePattern
= sum(1138/n)
where 0 < n < 16
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoReqV11
Object : bts
Function : Total number of handovers on TCH required. This formula does not
take into account the addition of screenings 1138/14, 1138/15, or
1138/16.
Formula : hoRequiredTchUplinkStrength
+ hoRequiredTchDownlinkStrength
+ hoRequiredTchUplinkQuality
+ hoRequiredTchDownlinkQuality
+ hoRequiredTchDistance
+ hoRequiredTchPowerBudgetQuality
+ hoRequiredTchCapture
+ hoRequiredTchIntraBtsOm
+ hoRequiredTchIntraBtsUplink
+ hoRequiredTchIntraBtsDownlink
+ hoRequiredTchDirectedRetry
+ hoRequiredTchTdmaClass0
+ hoRequiredTchTdmaClass1
+ hoRequiredTchInterBtsOm
= sum(1138/n)
where 0 < n < 13
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoReqSdcch
Object : bts
Function : Total number of handovers required on SDCCH: all causes
Formula : hoRequiredSdcchUplinkStrength
+ hoRequiredSdcchDownlinkStrength
+ hoRequiredSdcchUplinkQuality
+ hoRequiredSdcchDownlinkQuality
+ hoRequiredSdcchDistance
+ hoRequiredSdcchPowerBudget
+ hoRequiredSdcchCapture
+ hoRequiredSdcchIntraBtsOm
+ hoRequiredSdcchInterBtsOm
+ hoRequiredSdcchIntraBtsUplink
+ hoRequiredSdcchIntraBtsDownLink
+ hoRequiredSdcchTraffic
= 1139/0 + 1139/1 + 1139/2 + 1139/3 +
1139/4 + 1139/5 + 1139/6 + 1139/7 +
1139/13 + 1139/8 + 1139/9 + 1139/14
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoReqSdcchV11
Object : bts
Function : Total number of handovers required on SDCCH. This formula does
not take into account the introduction of the screening 1139/14.
Formula : hoRequiredSdcchUplinkStrength
+ hoRequiredSdcchDownlinkStrength
+ hoRequiredSdcchUplinkQuality
+ hoRequiredSdcchDownlinkQuality
+ hoRequiredSdcchDistance
+ hoRequiredSdcchPowerBudget
+ hoRequiredSdcchCapture
+ hoRequiredSdcchIntraBtsOm
+ hoRequiredSdcchInterBtsOm
+ hoRequiredSdcchIntraBtsUplink
+ hoRequiredSdcchIntraBtsDownLink
= 1139/0 + 1139/1 + 1139/2 + 1139/3 +
1139/4 + 1139/5 + 1139/6 + 1139/7 + 1139/13
+ 1139/8 + 1139/9
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoRequestIncoming
Object : bts
Function : Number of incoming intra-- and inter--BSS handovers on TCH
requested
Formula : hoRequestIncomingIntraBss
+ hoRequestIncomingInterBss
= 1069/0 + 1070/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoRequestIncomingSdcch
Object : bts
Function : Number of incoming intra-- and inter--BSS handovers on SDCCH
requested
Formula : hoRequestIncomingIntraBssSdcch
+ hoRequestIncomingInterBssSdcch
= 1144/0 + 1145/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoRequestOutgoing
Object : bts
Function : Number of outgoing intra-- and inter--BSS handovers on TCH
requested
Formula : hoRequestOutgoingIntraBss
+ hoRequestOutgoingInterBss
+ hoRequestIntraBts
= 1075/0 + 1076/0 + 1081/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoRequestOutgoingSdcch
Object : bts
Function : Number of outgoing intra-- and inter--BSS handovers requested on
SDCCH
Formula : hoRequestOutgoingIntraBssSdcch
+ hoRequestOutgoingInterBssSdcch
+ hoRequestIntraBtsSdcch
= 1150/0 + 1151/0 + 1154/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoSuccessIncoming
Object : bts
Function : Ratio of successful incoming handovers on TCH relative to all
handover execution attempts on TCH.
Formula : (1 -- (hoSuccessIncoming / hoExecutionIncoming))
* greaterperc(hoExecutionIncoming, signif1bts)
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoSuccessIncomingSdcch
Object : bts
Function : Ratio of successful incoming SDCCH handovers relative to all
incoming handover execution attempts on SDCCH
Formula : hoSuccessIncomingIntraBssSdcch
+ hoSuccessIncomingInterBssSdcch
= 1148/0 + 1149/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoSuccessOutgoing
Object : bts
Function : Ratio of successful outgoing handovers on TCH relative to all
handover execution attempts on TCH
Formula : hoSuccessOutgoingIntraBss
+ hoSuccessOutgoingInterBss
+ hoSuccessIntraBts
= 1067/0 + 1068/0 + 1083/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoSuccessOutgoingFirst
Object : bts
Function : Number of successful outgoing inter-- and intra--BSS handovers on
TCH after first attempt
Formula : hoSuccessOutgoingFirstIntra
+ hoSuccessOutgoingFirstInter
= 1077/0 + 1078/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoSuccessOutgoingFirstSdcch
Object : bts
Function : Number of successful outgoing intra-- and inter--BSS handovers on
SDCCH after first attempt
Formula : hoSuccessOutgoingFirstIntraSdcch
+ hoSuccessOutgoingFirstInterSdcch
= 1152/0 + 1153/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : hoSuccessOutgoingSdcch
Object : bts
Function : Ratio of successful outgoing handovers on SDCCH, relative
to all outgoing handover execution attempts on SDCCH
Formula : hoSuccessOutgoingIntraBssSdcch
+ hoSuccessOutgoingInterBssSdcch
+ hoSuccessIntraBtsSdcch
= 1142/0 + 1143/0 + 1156/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : contentionFailureRatioOnePhaseAccess
Object : ccch
Function : Ratio of the number of failures of the contention resolution procedure
in case to the cumulative number of Immediate Assignment Uplink
messages sent by the PCU in the case of one phase access, scaled to the
cumulative number of one phase access RACH (Channel Request)
received by the PCU
Formula : (pcuContentionFailureOnePhase
/ pcuUpTbfImmediateAssignmentOnePhase) *
100
* greater (pcuChannelRequestOnePhase,
100
* greater (pcuUpTbfImmediateAssignmentOnePhase, 0)
15192/0
= ------ - - - - * 100
15191/0
* greater (15190/0, 100)
* greater (15191/0, 0)
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
Name Q3 : gprsFailureRatioOnePhaseAccess
Object : ccch
Function : Ratio of the number of Immediate Assignment Uplink messages sent
by the PCU to establish a one phase access UL TBF relative to the
cumulative number of one phase access RACH (Channel Request)
received by the PCU
Formula : (1 - (pcuUpTbfImmediateAssignmentOnePhase
/ pcuChannelRequestOnePhase) ) * 100
* greater (pcuChannelRequestOnePhase, 100)
* greater (pcuUpTbfImmedaiteAssignmentOnePhase, 0)
15191/0
= (1 ------------ - ) * 100
15190/0
* greater (15190/0, 100)
* greater (15191/0, 0)
Name Q3 : gprsFailureRatioTwoPhaseAccess
Object : ccch
Function : The ratio of the total number of PACKET RESOURCE REQUEST
messages received by the PCU from the MS in the second phase of the
2--phase access uplink TBF establishment, relative to the number of
IMMEDIATE ASSIGNMENT messages sent in the first phase of
two--phase assignment
Formula : (1 - (packetResourceRequest
/ tpaImmediateAssignment)) * 100
* greater (tpaImmedaiteAssignment, 100)
15056/1
= ( 1 -- ------ - - - - - - - - - - - - - ) * 100
15058/0 -- 15191/0
Name Q3 : tpaImmediateAssignment
Object : ccch
Function : The number of IMMEDIATE ASSIGNMENT messages sent in the
first phase of two--phase assignment
Formula : upTbfImmediateAssignment
- pcuUpTbfImmediateAssignmentOnePhase
= 15058/0 -- 15191/0
Class : synthetic permanent
Source : calculated by the OMC when the user asks for an observation report
These totalizer counters are provided by the SYBASE OMC--R agent server. They
are read by the OMC--R agent self-observation task at the end of each
mdGranularityPeriod.
ll
9940 Total number of SYBASE errors
Name Q3 : sybaseTotalError
Object : SYBASE agent server
Function : number of anomalies detected by the SYBASE server during disk
read/write operations in the observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
9941 Total number of SYBASE read operations
Name Q3 : sybaseTotalRead
Object : SYBASE agent server
Function : number of disk read operations performed by the SYBASE server in
the observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
9942 Total number of SYBASE write operations
Name Q3 : sybaseTotalWrite
Object : SYBASE agent server
Function : number of disk write operations performed by the SYBASE server in
the observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
9943 CPU time used by the SYBASE server (1/10 s)
Name Q3 : sybaseCpuBusy
Object : SYBASE agent server
Function : CPU time used by the SYBASE server in the observation period,
expressed in 1/10th of a second
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
9944 I/O time used by the SYBASE server (1/10 s)
Name Q3 : sybaseIoBusy
Object : SYBASE agent server
Function : time spent by the SYBASE server in input/output operations during
the observation period, expressed in 1/10th of a second
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
9945 SYBASE server idle time (s)
Name Q3 : sybaseIdle
Object : SYBASE agent server
Function : time of SYBASE server unoccupancy in the observation period,
expressed in seconds
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
9946 Number of packets received by the SYBASE server
Name Q3 : sybasePacketIn
Object : SYBASE agent server
Function : number of data packets received by the SYBASE server in the
observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
9947 Number of packets sent by the SYBASE server
Name Q3 : sybasePacketOut
Object : SYBASE agent server
Function : number of data packets sent by the SYBASE server in the observation
period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
9948 Number of erroneous packets sent or received by the SYBASE
server
Name Q3 : sybasePacketErr
Object : SYBASE agent server
Function : number of anomalies detected by the SYBASE server when sending
or receiving data packets in the observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
10047 Average filling rate of configuration database cm_db
Name Q3 : cmDatabaseUsed
cmDatabaseUsedCum . . . . . . . . . . Total filling rate
cmDatabaseUsedEch . . . . . . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of
configuration “cm_db” database used, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
10048 Average filling rate of fault database fm_db
Name Q3 : fmDatabaseUsed
fmDatabaseUsedCum . . . . . . . . . . Total filling rate
fmDatabaseUsedEch . . . . . . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of fault
“fm_db” database used, calculated at the end of the observation
period, expressed in %
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
10049 Average filling rate of configuration log cm_db
Name Q3 : cmLogUsed
cmLogUsedCum . . . . . . . . . . . . . . Total filling rate
cmLogUsedEch . . . . . . . . . . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of
configuration “cm_db” log used, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
10050 Average filling rate of fault log fm_db
Name Q3 : fmLogUsed
fmLogUsedCum . . . . . . . . . . . . . . . Total filling rate
fmLogUsedEch . . . . . . . . . . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of fault
“fm_db” log used, calculated at the end of the observation period,
expressed in %
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R agent
ll
9974 Total number of association release requests sent by the BSC
Name Q3 : scseTotAssocFree
Object : active OMC--R agent server
Function : number of association release requests sent by the BSC in the
observation period
Type : raw permanent
Source : SCSE service, calculated by the OMC--R agent
ll
9988 Average filling rate of NMC server SWAP area
Name Q3 : unixSwapNMCSrv
unixSwapNMCSrvCum . . . . . . . . . Total filling rate of SWAP area
unixSwapNMCSrvEch . . . . . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of swap
memory used in the server, calculated at the end of the observation
period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
9990 Average filling rate of NMC server “/” partition
Name Q3 : unixRootPartitionNMCSrv
unixRootPartitionNMCSrvCum . . Total partition filling rate
unixRootPartitionNMCSrvEch . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
root partition used in the server, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
9991 Average filling rate of NMC server “/tmp” partition
Name Q3 : unixTmpPartitionNMCSrv
unixTmpPartitionNMCSrvCum . . Total partition filling rate
unixTmpPartitionNMCSrvEch . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/tmp” partition used in the server, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
9993 Average filling rate of “/MD/obs” partition
Name Q3 : unixObsPartition
unixObsPartitionCum . . . . . . . . . . Total partition filling rate
unixObsPartitionEch . . . . . . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/MD/obs” partition used in the server, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
9994 Average filling rate of “/MD/notif” partition
Name Q3 : unixNotifPartition
unixNotifPartitionCum . . . . . . . . . Total partition filling rate
unixNotifPartitionEch . . . . . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/MD/notif” partition used in the server, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
9995 Average filling rate of “/MD/restored/obs” partition
Name Q3 : unixRestoredObsPartition
unixRestoredObsPartitionCum . . . Total partition filling rate
unixRestoredObsPartitionEch . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/MD/restored/obs” partition used in the server, calculated at the end
of the observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
9996 Average filling rate of “/MD/restored/notif” partition
Name Q3 : unixRestoredNotifPartition
unixRestoredNotifPartitionCum . . Total partition filling rate
unixRestoredNotifPartitionEch . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/MD/restored/notif” partition used in the server, calculated at the end
of the observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
9997 Average filling rate of “/MD/trace_function” partition
Name Q3 : unixTracePartition
unixTracePartitionCum . . . . . . . . . Total partition filling rate
unixTracePartitionEch . . . . . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/MD/trace_function” partition used in the server, calculated at the
end of the observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
9998 Average filling rate of “/MD/data/ssn” partition
Name Q3 : unixDataSsnPartition
unixDataSsnPartitionCum . . . . . . . Total partition filling rate
unixDataSsnPartitionEch . . . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/MD/data/ssn” partition used in the server, calculated at the end of
the observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
9999 Average filling rate of “/MD/restored/trace_function” partition
Name Q3 : unixRestoredTracePartition
unixRestoredTracePartitionCum . . Total partition filling rate
unixRestoredTracePartitionEch . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/MD/restored/trace_function” partition used in the server, calculated
at the end of the observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
10043 Average filling rate of NMC server “/MD/base” partition
Name Q3 : unixMdrBasePartitionNMCSrv
unixMdrBasePartitionNMCSrvCum . . . . . Total partition filling rate
unixMdrBasePartitionNMCSrvEch . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/MD/base” partition used in the server, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
10044 Average filling rate of NMC server “/MD/data” partition
Name Q3 : unixMdrDataPartitionNMCSrv
unixMdrDataPartitionNMCSrvCum . . . . . Total partition filling rate
unixMdrDataPartitionNMCSrvEch . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/MD/data” partition used in the server, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
10045 Average filling rate of NMC server “/CMN/base” partition
Name Q3 : unixCmnBasePartitionNMCSrv
unixCmnBasePartitionNMCSrvCum . . . . Total partition filling rate
unixCmnBasePartitionNMCSrvEch . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/CMN/base” partition used in the server, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
10046 Average filling rate of NMC server “/CMN/data” partition
Name Q3 : unixCmnDataPartitionNMCSrv
unixCmnDataPartitionNMCSrvCum . . . . Total partition filling rate
unixCmnDataPartitionNMCSrvEch . . . . . . Number of samples
Object : active OMC--R agent server
Function : average rate (= total rate divided by the number of samples) of disk
“/CMN/data” partition used in the server, calculated at the end of the
observation period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R agent
ll
10001 Number of CMIS GET confirmations sent for the md subtree
Name Q3 : ommdGetConf
Object : active OMC--R agent server
Function : number of CMIS GET confirmations about md subtree objects sent in
the observation period
Event : transmission of a CMIS GET confirmation about an md subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10002 Number of CMIS CREATE requests received for the md subtree
Name Q3 : ommdCreRequest
Object : active OMC--R agent server
Function : number of CMIS CREATE requests about md subtree objects
received in the observation period
Event : receipt of a CMIS CREATE request about an md subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10003 Number of CMIS CREATE confirmations sent for the md
subtree
Name Q3 : ommdCreConf
Object : active OMC--R agent server
Function : number of CMIS CREATE confirmations about md subtree objects
sent in the observation period
Event : transmission of a CMIS CREATE confirmation about an md subtree
object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10004 Number of CMIS SET requests received for the md subtree
Name Q3 : ommdSetRequest
Object : active OMC--R agent server
Function : number of CMIS SET requests about md subtree objects received in
the observation period
Event : receipt of a CMIS SET request about an md subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10005 Number of CMIS SET confirmations sent for the md subtree
Name Q3 : ommdSetConf
Object : active OMC--R agent server
Function : number of CMIS SET confirmations about md subtree objects sent in
the observation period
Event : transmission of a CMIS SET confirmation about an md subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10006 Number of CMIS DELETE requests received for the md subtree
Name Q3 : ommdDelRequest
Object : active OMC--R agent server
Function : number of CMIS DELETE requests about md subtree objects
received in the observation period
Event : receipt of a CMIS DELETE request about an md subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10007 Number of CMIS DELETE confirmations sent for the md
subtree
Name Q3 : ommdDelConf
Object : active OMC--R agent server
Function : number of CMIS DELETE confirmations about md subtree objects
sent in the observation period
Event : transmission of a CMIS DELETE confirmation about an md subtree
object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10008 Number of CMIS ACTION requests received for the md subtree
Name Q3 : ommdActRequest
Object : active OMC--R agent server
Function : number of CMIS ACTION requests about md subtree objects
received in the observation period
Event : receipt of a CMIS ACTION request about an md subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10009 Number of CMIS ACTION confirmations sent for the md subtree
Name Q3 : ommdActConf
Object : active OMC--R agent server
Function : number of CMIS ACTION confirmations about md subtree objects
sent in the observation period
Event : transmission of a CMIS ACTION confirmation about an md subtree
object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10010 Number of CMIS CANCEL GET requests received for the md
subtree
Name Q3 : ommdCancelGetRequest
Object : active OMC--R agent server
Function : number of CMIS CANCEL GET requests about md subtree objects
received in the observation period
Event : receipt of a CMIS CANCEL GET request about an md subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10011 Number of CMIS CANCEL GET confirmations sent for the md
subtree
Name Q3 : ommdCancelGetConf
Object : active OMC--R agent server
Function : number of CMIS CANCEL GET confirmations about md subtree
objects sent in the observation period
Event : transmission of a CMIS CANCEL GET confirmation about an md
subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10012 Number of CMIS GET requests received for the network subtree
Name Q3 : omnetGetRequest
Object : active OMC--R agent server
Function : number of CMIS GET requests about network subtree objects
received in the observation period
Event : receipt of a CMIS GET request about a network subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10013 Number of CMIS GET confirmations sent for the network
subtree
Name Q3 : omnetGetConf
Object : active OMC--R agent server
Function : number of CMIS GET confirmations about network subtree objects
sent in the observation period
Event : transmission of a CMIS GET confirmation about a network subtree
object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10014 Number of CMIS CREATE requests received for the network
subtree
Name Q3 : omnetCreRequest
Object : active OMC--R agent server
Function : number of CMIS CREATE requests about network subtree objects
received in the observation period
Event : receipt of a CMIS CREATE request about a network subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10015 Number of CMIS CREATE confirmations sent for the network
subtree
Name Q3 : omnetCreConf
Object : active OMC--R agent server
Function : number of CMIS CREATE confirmations about network subtree
objects sent in the observation period
Event : transmission of a CMIS CREATE confirmation about a network
subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
l
10016 Number of CMIS SET requests received for the network subtree
Name Q3 : omnetSetRequest
Object : active OMC--R agent server
Function : number of CMIS SET requests about network subtree objects
received in the observation period
Event : receipt of a CMIS SET request about a network subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10017 Number of CMIS SET confirmations sent for the network
subtree
Name Q3 : omnetSetConf
Object : active OMC--R agent server
Function : number of CMIS SET confirmations about network subtree objects
sent in the observation period
Event : transmission of a CMIS SET confirmation about a network subtree
object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10018 Number of CMIS DELETE requests received for the network
subtree
Name Q3 : omnetDelRequest
Object : active OMC--R agent server
Function : number of CMIS DELETE requests about network subtree objects
received in the observation period
Event : receipt of a CMIS DELETE request about a network subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10019 Number of CMIS DELETE confirmations sent for the network
subtree
Name Q3 : omnetDelConf
Object : active OMC--R agent server
Function : number of CMIS DELETE confirmations about network subtree
objects sent in the observation period
Event : transmission of a CMIS DELETE confirmation about a network
subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10020 Number of CMIS ACTION requests received for the network
subtree
Name Q3 : omnetActRequest
Object : active OMC--R agent server
Function : number of CMIS ACTION requests about network subtree objects
received in the observation period
Event : receipt of a CMIS ACTION request about a network subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10021 Number of CMIS ACTION confirmations sent for the network
subtree
Name Q3 : omnetActConf
Object : active OMC--R agent server
Function : number of CMIS ACTION confirmations about network subtree
objects sent in the observation period
Event : transmission of a CMIS ACTION confirmation about a network
subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10022 Number of CMIS CANCEL GET requests received for the
network subtree
Name Q3 : omnetCancelGetRequest
Object : active OMC--R agent server
Function : number of CMIS CANCEL GET requests about network subtree
objects received in the observation period
Event : receipt of a CMIS CANCEL GET request about a network subtree
object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10023 Number of CMIS CANCEL GET confirmations sent for the
network subtree
Name Q3 : omnetCancelGetConf
Object : active OMC--R agent server
Function : number of CMIS CANCEL GET confirmations about network
subtree objects sent in the observation period
Event : transmission of a CMIS CANCEL GET confirmation about a network
subtree object
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10024 Number of notifications received
Name Q3 : notifsReceived
Object : active OMC--R agent server
Function : number of notifications received by the secured notification server of
the OMC--R agent in the observation period
Event : receipt of a notification by the secured notification server
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10025 Number of notifications sent for the first time
Name Q3 : notifsSentOnce
Object : active OMC--R agent server
Function : number of notifications transmitted a first time to the managers in the
observation period
Event : first transmission of a notification to the managers
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10026 Number of notifications sent a second time
Name Q3 : notifsTransmitAgainOnce
Object : active OMC--R agent server
Function : number of notifications transmitted a second time to the managers in
the observation period
Event : second transmission of a notification to the managers
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10027 Number of notifications sent more than two times
Name Q3 : notifsTransmitAgainTwiceAndMore
Object : active OMC--R agent server
Function : number of notifications transmitted more than two times to the
managers in the observation period
Event : more than two transmissions of a notification to the managers
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10028 Number of notifications that were not sent to all managers
Name Q3 : notifsReachMaxTransmit
Object : active OMC--R agent server
Function : number of notifications that cannot be transmitted to all the managers
in the observation period
Event : stop transmitting a same notification to the managers
Type : raw permanent
Source : CMIS service, calculated by the OMC--R agent
ll
10029 Number of FTAM GET transfer requests
Name Q3 : ftamFtiGet
Object : active OMC--R agent server
Function : number of FTAM GET transfers requested in the observation period
Event : start of an FTAM GET transfer
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
ll
10030 Number of successful FTAM GET transfers
Name Q3 : ftamFtiGetConf
Object : active OMC--R agent server
Function : number of successful FTAM GET transfers in the observation period
Event : normal completion of an FTAM GET transfer
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
ll
10031 Number of FTAM PUT transfer requests
Name Q3 : ftamFtiPut
Object : active OMC--R agent server
Function : number of FTAM PUT transfers requested in the observation period
Event : start of an FTAM PUT transfer
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
ll
10032 Number of successful FTAM PUT transfers
Name Q3 : ftamFtiPutConf
Object : active OMC--R agent server
Function : number of successful FTAM PUT transfers in the observation period
Event : normal completion of an FTAM PUT transfer
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
ll
10033 Number of FTAM DELETE requests
Name Q3 : ftamFtiDelete
Object : active OMC--R agent server
Function : number of FTAM DELETE requests in the observation period
Event : transmission of an FTAM DELETE request
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
ll
10034 Number of successful FTAM DELETE requests
Name Q3 : ftamFtiDeleteConf
Object : active OMC--R agent server
Function : number of successful FTAM DELETE requests in the observation
period
Event : normal completion of an FTAM DELETE request
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
ll
10035 Number of FTAM DIR transfer requests
Name Q3 : ftamFtiDir
Object : active OMC--R agent server
Function : number of FTAM DIR transfers requested in the observation period
Event : start of an FTAM DIR transfer
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
ll
10036 Number of successful FTAM DIR transfers
Name Q3 : ftamFtiDirConf
Object : active OMC--R agent server
Function : number of successful FTAM DIR transfers in the observation period
Event : normal completion of an FTAM DIR transfer
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
ll
10037 Number of FTAM RENAME requests
Name Q3 : ftamFtiRename
Object : active OMC--R agent server
Function : number of FTAM RENAME requests in the observation period
Event : transmission of an FTAM RENAME request
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
ll
10038 Number of successful FTAM RENAME requests
Name Q3 : ftamFtiRenameConf
Object : active OMC--R agent server
Function : number of successful FTAM RENAME requests in the observation
period
Event : normal completion of an FTAM RENAME request
Type : raw permanent
Source : FTAM service, calculated by the OMC--R agent
These totalizer counters are provided by the SYBASE server. They are read by the
OMC--R manager self-observation task at the end of each observation period (static
configuration data).
ll
Total number of SYBASE errors
Name : omcSybaseTotalError
Object : SYBASE server (OMC--R manager and connected workstations)
Function : number of anomalies detected by the SYBASE server during disk
read/write operations in the observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R manager
ll
Total number of SYBASE read operations
Name : omcSybaseTotalRead
Object : SYBASE server (OMC--R manager and connected workstations)
Function : number of disk read operations performed by the SYBASE server in
the observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R manager
ll
Total number of SYBASE write operations
Name : omcSybaseTotalWrite
Object : SYBASE server (OMC--R manager and connected workstations)
Function : number of disk write operations performed by the SYBASE server in
the observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R manager
ll
CPU time used by the SYBASE server (1/10 s)
Name : omcSybaseCpuBusy
Object : SYBASE server (OMC--R manager and connected workstations)
Function : CPU time used by the SYBASE server in the observation period,
expressed in 1/10th of a second
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R manager
ll
I/O time used by the SYBASE server (1/10 s)
Name : omcSybaseIoBusy
Object : SYBASE server (OMC--R manager and connected workstations)
Function : time spent by the SYBASE server in input/output operations during
the observation period, expressed in 1/10th of a second
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R manager
ll
SYBASE server idle time (s)
Name : omcSybaseIdle
Object : SYBASE server (OMC--R manager and connected workstations)
Function : time of SYBASE server unoccupancy in the observation period,
expressed in seconds
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R manager
ll
Number of packets received by the SYBASE server
Name : omcSybasePacketIn
Object : SYBASE server (OMC--R manager and connected workstations)
Function : number of data packets received by the SYBASE server in the
observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R manager
ll
Number of packets sent by the SYBASE server
Name : omcSybasePacketOut
Object : SYBASE server (OMC--R manager and connected workstations)
Function : number of data packets sent by the SYBASE server in the observation
period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R manager
ll
Number of erroneous packets sent or received by the SYBASE server
Name : omcSybasePacketErr
Object : SYBASE server (OMC--R manager and connected workstations)
Function : number of anomalies detected by the SYBASE server when sending
or receiving data packets in the observation period
Type : raw permanent
Source : SYBASE server, calculated by the OMC--R manager
ll
Average filling rate of omc_db database
Name : omcDatabaseUsed
omcDatabaseUsedCum . . . . . . . . . Total filling rate
omcDatabaseUsedEch . . . . . . . . . . Number of samples
Object : active OMC--R manager server
Function : average rate (= total rate divided by the number of samples) of
“cm_db” database used, calculated at the end of the observation
period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R manager
ll
Average filling rate of segment 0 of trace_db database
Name : traceDatabaseSeg0Used
traceDatabaseSeg0UsedCum . . . . . Total filling rate
traceDatabaseSeg0UsedEch . . . . . . Number of samples
Object : active OMC--R manager server
l
Number of abort requests received on port x
Name : omcX25AbortsPort0
omcX25AbortsPort1
omcX25AbortsPort2
omcX25AbortsPort3
Object : active server (OMC--R manager and connected workstations)
Function : number of aborted frames received on the X.25 port 0 or 1 in the
observation period
Event : receipt 8 consecutive times on the X.25 port of a frame that does not
comply with HDLC frame numbering
Type : raw permanent
Source : X.25--2 layer, calculated by the OMC--R manager
ll
Average filling rate of SWAP area
Name : omcUnixSwap
omcUnixSwapCum . . . . . . . . . . . . Total filling rate of SWAP area
omcUnixSwapEch . . . . . . . . . . . . . Number of samples
Object : active server (OMC--R manager and connected workstations)
Function : average rate (= total rate divided by the number of samples) of swap
memory used in the server, calculated at the end of the observation
period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R manager
ll
Average filling rate of “/” partition
Name : omcUnixRootPartition
omcUnixRootPartitionCum . . . . . . Total partition filling rate
omcUnixRootPartitionEch . . . . . . . Number of samples
Object : active server (OMC--R manager and connected workstations)
Function : average rate (= total rate divided by the number of samples) of disk
root partition used, calculated at the end of the observation period,
expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R manager
ll
Average filling rate of “/tmp” partition
Name : omcUnixTmpPartition
omcUnixTmpPartitionCum . . . . . . Total partition filling rate
omcUnixTmpPartitionEch . . . . . . . Number of samples
Object : active server (OMC--R manager and connected workstations)
Function : average rate (= total rate divided by the number of samples) of disk
“/tmp” partition used, calculated at the end of the observation period,
expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R manager
ll
Average filling rate of “/OMC/obs” partition
Name : omcUnixObsPartition
omcUnixObsPartitionCum . . . . . . . Total partition filling rate
omcUnixObsPartitionEch . . . . . . . Number of samples
Object : active OMC--R manager server
Function : average rate (= total rate divided by the number of samples) of disk
“/OMC/obs” partition used, calculated at the end of the observation
period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R manager
ll
Average filling rate of “/OMC/mail” partition
Name : omcUnixMailPartition
omcUnixMailPartitionCum . . . . . . Total partition filling rate
omcUnixMailPartitionEch . . . . . . . Number of samples
Object : active OMC--R manager server
Function : average rate (= total rate divided by the number of samples) of disk
“/OMC/mail” partition used, calculated at the end of the observation
period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R manager
ll
Average filling rate of “/OMC/base” partition
Name : omcUnixBasePartition
omcUnixBasePartitionCum . . . . . . Total partition filling rate
omcUnixBasePartitionEch . . . . . . . Number of samples
Object : active OMC--R manager server
Function : average rate (= total rate divided by the number of samples) of disk
“/OMC/base” partition used, calculated at the end of the observation
period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R manager
ll
Average filling rate of “/OMC/data” partition
Name : omcUnixDataPartition
omcUnixDataPartitionCum . . . . . . Total partition filling rate
omcUnixDataPartitionEch . . . . . . . Number of samples
Object : active OMC--R manager server
Function : average rate (= total rate divided by the number of samples) of disk
“/OMC/data” partition used, calculated at the end of the observation
period, expressed in %
Type : raw permanent
Source : SUNOS system, calculated by the OMC--R manager
l
15004/0 Number of UNIT--DATA PDUs received downlink by the BVC
Name Q3 : pduDataDn
Value range : [0 to 4294967295]
Object : bts
Function : Number of BSSGP DL--UNITDATA PDU received by the BVC
(SGSN-->PCU).
Event : Receiving of a DL--UNITDATA PDU
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15004/1 Number of UNIT--DATA PDUs sent uplink by the BVC
Name Q3 : pduDataUp
Value range : [0 to 4294967295]
Object : bts
Function : Number of BSSGP UL--UNITDATA PDU sent by the BVC
(PCU-->SGSN).
Event : Sending of a UL--UNITDATA PDU
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15005/0 Number of bytes received by the BVC in DL--UNIT--DATA PDUs
Name Q3 : octetsDataDn
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative size (in bytes) of all the LLC PDU in the BSSGP
DL--UNITDATA PDU received by the BVC (SGSN-->PCU).
Event : Receiving of a DL--UNITDATA PDU
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Data flows : Refer to Chapter 2
DFD “PCUSN: Flow Control”
DFD “PCUSN: LLC Discarded”
Note : V12.4b and c counter
l
15005/1 Number of bytes sent by the BVC in the UL--UNIT--DATA PDUs
Name Q3 : octetsDataUp
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative size (in bytes) of all the BSSGP UL--UNITDATA PDU
sent by the BVC (PCU-->SGSN). The size does not include the FR,
NS, and BSSGP header sizes.
Event : Sending of a UL--UNITDATA PDU
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15007/0 Number of times octets discarded because the number of received
PDUs exceeds the bucket size
Name Q3 : octetDiscarded
Value range : 0 to 65535
Object : bts
Function : Number of octets discarded, because the number of received PDUs
exceeds the bucket size
Event : This counter is incremented after the deletion of a PDU at the PCU
level
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15007/1 Cumulative size and time of all the GPRS RLC data blocks sent for
the first time on a pipe
Name Q3 : pcuDlThroughputCum
Function : Cumulated size in bytes of all the GPRS RLC data blocks sent for the
first time (i.e. fresh block) on a pipe.
For cumulative time:
T0 = Time of the first block sent in downlink for that mobile
T1 = Time of the last FRESH or NACKED block
T2 = Time of the PDAN which acknowledge all the downlink blocks
(or PCA in unacknowledged mode). Note that if the PDAN is never
received, T1 corresponds to the release of the DL TBF (in that case the
PCU computes T1 - T0 + 1).
Event : The event for the cumulative size function is a GPRS RLC data block
is sent for the first time (i.e. fresh block) on a pipe by a GPRS DL TBF.
For the cumulative time function, T2 which increments the counter
with the result of T1--T0+1=T2--T0--(RTD + RRBP) +1
Name Q3 : pcuD1ThroughputNbs
Function : Cumulated time in multiple of 20 ms where the MS is in GPRS DL
data transfer.
T0 = Time of the first FRESH block sent to the mobile
T1 = Time of the last FRESH or NACK block sent to the mobile
Each time the last temporary FRESH or NACK block is sent, the PCU
stores the time T1, when the last PDAN (which acknowledged all the
DL blocks or PCA in unacknowledged block) is received the PCU
increments the counter with T1--T0+1 (by using the last T1 value
stored in memory).
Event : A GPRS RLC data block is sent for the first time (i.e. fresh block) on a
pipe by a GPRS DL TBF.
Name Q3 : AvgDlThroughput
Function : To allow the computation of the AvgDlThroughput counter, the
PCUOAM will receive 2 PCU counters from the PCUSN, { Bvc,
maxSizeDataDn } and { Bvc, maxSizeDataUp } and will transform
them to pcuDlThroughputCum (15007/1 CUM CELL) and
pcuDlThroughputNbs (15007/1 NBS CELL).
The current transformation { Bvc, bvcUnBlockRequests } =>
AvgDlThroughput (15007/1 AVG CELL), performed by the
PCUOAM, will have to be removed. The SDO will create itself
AvgDlThroughput (15007/1 AVG CELL).
Event : A GPRS RLC data block is sent for the first time (i.e. fresh block) on a
pipe by a GPRS DL TBF.
Note : There are three counters with an irregular sampling:
AvgDlThroughput (15007/1 AVG CELL), dyAgprsAvgNbTimeslots
(15075/1 AVG CELL), dyAgprsAvgLoadCriterion (15076/0 AVG
CELL). After modification, these counters will have the same SDO
names; there is no interface rupture.
Value range : 0 to 4294967295
Object : bts
Unit : bytes
Source : recorded by the PCU
l
15008/0 Maximum value of Downlink radio throughput calculated by the
flow control algorithm. (No longer relevant at the PCU level; it is
always set to 0.)
Name Q3 : MaxDlThroughput
Value range : 0 to 65535
Object : bts
Function : This counter is not relevant at the PCU level anymore; it is always set
to 0.
Event : This counter is incremented after the emission of 3 Kbytes on the
radio
Unit : 100 Bits per second
Source : recorded by the PCU
Feature : GPRS
Note : The lie factor is a feature that is used to exaggerate the leak rate when
the bucket is near starvation, and to minimize the leak rate when the
bucket is almost full. This counter calculates the true maximum value
of the downlink radio throughput without using the lie factor
l
15010/0 Number of FLOW--CONTROL--BVC PDUs sent by the BVC
Name Q3 : bvcFlowControlRequests
Value range : [0 to 65535]
Object : bts
Function : Number of BSSGP FLOW--CONTROL--BVC PDU sent by the BVC
(PCU-->SGSN).
Event : Sending of a FLOW--CONTROL--BVC PDU
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15010/1 Number of FLOW--CONTROL--MS PDUs sent by the BVC
Name Q3 : msFlowControlRequests
Value range : [0 to 32767]
Object : bts
Function : Number of BSSGP FLOW--CONTROL--MS PDU sent by the BVC
(PCU-->SGSN).
Event : Sending of a FLOW--CONTROL--MS PDU
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15012/0 Number of LLC--DISCARDED PDUs sent by the BVC
Name Q3 : llcDiscardedPdu
Value range : [0 to 65535]
Object : bts
Function : Number of BSSGP LLC--DISCARDED PDU sent for the BVC
(PCU-->SGSN).
Event : Sending of a LLC--DISCARDED PDU
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15012/1 Cumulative amount of the all the bytes discarded in the BVC
Name Q3 : llcDiscardedOctets
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative amount of the all the bytes discarded in the BVC (i.e.
number of bytes discarded from the bucket if not empty)
Event : This counter is triggered by the:
sending of a BSSGP LLC DISCARDED PDU to the SGSN
sending of a BSSGP RADIO STATUS to the SGSN
reception of a BSSGP FLUSH--LL from the SGSN
Source : recorded by the PCU
l
15023/1 Total Number of PS Paging messages sent by the PCU to the BTS on
this LAPD link
Name : PsPagingOnCCCH
Value range : 0 to 4294967295
Object : pcmCircuit
Function : Total Number of PS Paging messages sent by the PCU to the BTS on
this LAPD link
Event : This counter is incremented after the sending of a PS Paging message
to the BTS on the LAPD link
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
Reserved for future use
l
15024/0 Total Number of CS Paging messages sent by the PCU to the MS on
PACCH
Name Q3 : CsPagingOnPACCH
Value range : 0 to 4294967295
Object : pcmCircuit
Function : Total Number of CS Paging messages sent by the PCU to the MS on
PACCH (on this SPM card)
Event : This counter is incremented after the sending of a CS Paging message
to the MS on PACCH
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
Reserved for future use
l
15028/1 Cumulative number of uplink and/or downlink radio resource
assignments for a mobile whose multislot class requires 1 uplink
timeslot
Name Q3 : upMultiSlotRequest1
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class requires 1
uplink timeslot
Event : End of the packet transfer for the MS, if the MSC is known.
Source : recorded by the PCU
Precise
incrementation conditions :
The counter is not incremented if the multislot class is unknown.
The counter is incremented in case of normal or abnormal
termination.
Feature : GPRS
Note : V12.4d counter
Note : I/F PCU--PCUOAM: The counter upMultiSlotRequest is of type
vector using Index from 1 to 4.
Note : An EDGE--capable MS can have a different MCS in EDGE and in
GPRS. If the EDGE MS is allocated in EDGE mode, the EDGE MCS
will be considered for this counter. If the EDGE MS is allocated in
GPRS mode, the GPRS MCS will be considered for this counter.
Function : Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class requires
up to 2 uplink timeslots. If more than 4 timeslots are allocated in
uplink, the counter upMultislotRequest4 is incremented.
Index 0 is formatted in the Passport spooled statistic record but its
corresponding value must not be interpreted.
Index 2 corresponds to upMultiSlotRequests (2)
Index 3 corresponds to upMultiSlotRequests (3)
Index 4 corresponds to upMultiSlotRequests (4)
Event : End of the packet transfer for the MS, if the MSC is known.
Source : recorded by the PCU
Precise
incrementation conditions :
The counter is not incremented if the multislot class is unknown.
The counter is incremented in case of normal or abnormal
termination.
Feature : GPRS
Note : V12.4d counter
l
15028/3 Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class
requires up to 3 uplink timeslots
Name Q3 : upMultiSlotRequest3
Value range : [0 to 4294967295]
Object : bts
Feature : GPRS
Note : V12.4d counter
l
15028/4 Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class
requires up to 4 and more than 4 uplink timeslots
Name Q3 : upMultiSlotRequest4
Value range : [0 to 4294967295]
Object : bts
Feature : GPRS
Note : V12.4d counter
Note : I/F PCU--PCUOAM: The counter upMultiSlotRequest is of type
vector using Index from 1 to 4.
Note : If more than 4 timeslots are allocated in uplink, the counter
upMultislotRequest4 is incremented.
Note : A EDGE capable MS can have a different MCS in EDGE and in
GPRS. If the EDGE MS is allocated in EDGE mode, the EDGE MCS
will be considered for this counter. If the EDGE MS is allocated in
GPRS mode, the GPRS MCS will be considered for this counter.
l
15029/1 Cumulative number of gold users’ uplink allocations with a
satisfaction rate equal or better than 90%
Name Q3 : upTbfGoldSatisfactMore90pCent
Value range : 0 to 4294967295
Object : bts
Function : Cumulative number of gold users uplink allocations with a
satisfaction rate equal or better than 90 %. Refer to Section 4.7
Event : Modification of an allocation belonging to a gold user. Refer to
Section 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15029/2 Cumulative number of gold users’ uplink allocations with a
satisfaction rate equal or more than 50% and strictly less than
90%
Name Q3 : upTbfGoldSatisfactBet5090pCent
Value range : 0 to 4294967295
Object : bts
Function : Cumulative number of gold users’ uplink allocations with a
satisfaction rate equal or more than 50% and strictly less than 90%
Refer to Section 4.7
Event : Modification of an allocation belonging to a gold user. Refer to
Section 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15029/3 Cumulative number of gold users’ uplink allocations with a
satisfaction rate strictly less than 50%
Name Q3 : upTbfGoldSatisfactLess50pCent
Value range : 0 to 4294967295
Object : bts
Function : Cumulative number of gold users’ uplink allocations with a
satisfaction rate strictly less than 50%. Refer to Section 4.7
Event : Modification of an allocation belonging to a gold user. Refer to
Section 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15029/4 Cumulative number of gold users’ uplink allocations rejected due
to the admittance control
Name Q3 : upTbfGoldRejectedForMinTput
Value range : 0 to 4294967295
Object : bts
Function : Cumulative number of gold users’ uplink allocations rejected due to
the admittance control
Event : This counter is incremented after the rejection of a new allocation to a
gold user due to admittance control
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15030/1 Cumulative number of uplink and/or downlink radio resource
assignments for a mobile whose multislot class requires 1
downlink timeslot
Name Q3 : dnMultiSlotRequest1
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class requires
up to 1 downlink timeslot.
If more than 4 timeslots are allocated in downlink, the counter
dnMultiSlotRequest4 is incremented.
Note : Index 0 is formatted in the Passport spooled statistic record but its
corresponding value must not be interpreted.
Index 2 corresponds to dnMultiSlotRequests2
Index 3 corresponds to dnMultiSlotRequests3
Index 4 corresponds to dnMultiSlotRequests4
Event : End of the packet transfer for the MS, if the MSC is known.
Source : recorded by the PCU
Precise
incrementation conditions :
The counter is not incremented if the multislot class is unknown.
The counter is incremented in case of normal or abnormal
termination.
Feature : GPRS
Note : V12.4d counter
Note : On I/F PCU--PCUOAM, the counter dnMultiSlotRequests is of type
vector using Index from 1 to 4.
Note : EGPRS: An EDGE capable MS can have a different MCS in EDGE
and in GPRS. If the EDGE MS is allocated in EDGE mode, the EDGE
MCS will be considered for this counter. If the EDGE MS is allocated
in GPRS mode, the GPRS MCS will be considered for this counter.
l
15030/2 Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class
requires up to 2 downlink timeslots
Name Q3 : dnMultiSlotRequest2
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class requires
up to 2 downlink timeslot.
If more than 4 timeslots are allocated in downlink, the counter
dnMultiSlotRequest4 is incremented.
Note : Index 0 is formatted in the Passport spooled statistic record but its
corresponding value must not be interpreted.
Index 2 corresponds to dnMultiSlotRequests2
Index 3 corresponds to dnMultiSlotRequests3
Index 4 corresponds to dnMultiSlotRequests4
Event : End of the packet transfer for the MS, if the MSC is known.
Source : recorded by the PCU
Precise
incrementation conditions :
The counter is not incremented if the multislot class is unknown.
The counter is incremented in case of normal or abnormal
termination.
Feature : GPRS
Note : V12.4d counter
Note : On I/F PCU--PCUOAM, the counter dnMultiSlotRequests is of type
vector using Index from 1 to 4.
Note : EGPRS: An EDGE capable MS can have a different MCS in EDGE
and in GPRS. If the EDGE MS is allocated in EDGE mode, the EDGE
MCS will be considered for this counter. If the EDGE MS is allocated
in GPRS mode, the GPRS MCS will be considered for this counter.
l
15030/3 Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class
requires up to 3 downlink timeslots
Name Q3 : dnMultiSlotRequest3
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class requires
up to 3 downlink timeslots
Note : Index 0 is formatted in the Passport spooled statistic record but its
corresponding value must not be interpreted.
Index 2 corresponds to dnMultiSlotRequests2
Index 3 corresponds to dnMultiSlotRequests3
Index 4 corresponds to dnMultiSlotRequests4
Event : End of the packet transfer for the MS, if the MSC is known.
Source : recorded by the PCU
Precise
incrementation conditions :
The counter is not incremented if the multislot class is unknown.
The counter is incremented in case of normal or abnormal
termination.
Feature : GPRS
Note : V12.4d counter
Note : On I/F PCU--PCUOAM, the counter dnMultiSlotRequests is of type
vector using Index from 1 to 4.
Note : Note on EGPRS: An EDGE capable MS can have a different MCS in
EDGE and in GPRS. If the EDGE MS is allocated in EDGE mode, the
EDGE MCS will be considered for this counter. If the EDGE MS is
allocated in GPRS mode, the GPRS MCS will be considered for this
counter.
l
15030/4 Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class
requires up to 4 and more than 4 downlink timeslots
Name Q3 : dnMultiSlotRequest4
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of uplink and/or downlink radio resource
assignments on PACCH for a mobile whose multislot class requires
up to 4 and more than 4 downlink timeslots
Note : Index 0 is formatted in the Passport spooled statistic record but its
corresponding value must not be interpreted.
Index 2 corresponds to dnMultiSlotRequests2
Index 3 corresponds to dnMultiSlotRequests3
Index 4 corresponds to dnMultiSlotRequests4
Event : End of the packet transfer for the MS, if the MSC is known.
Source : recorded by the PCU
Precise
incrementation conditions :
The counter is not incremented if the multislot class is unknown.
The counter is incremented in case of normal or abnormal
termination.
Feature : GPRS
Note : V12.4d counter
Note : On I/F PCU--PCUOAM, the counter dnMultiSlotRequests is of type
vector using Index from 1 to 4.
Note : EGPRS: An EDGE capable MS can have a different MCS in EDGE
and in GPRS. If the EDGE MS is allocated in EDGE mode, the EDGE
MCS will be considered for this counter. If the EDGE MS is allocated
in GPRS mode, the GPRS MCS will be considered for this counter.
l
15031/1 First Downlink Unit Data Frame
Name Q3 : FirstDlUnitDataFrame
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of pre--established downlink TBF without
reception of DL--UNITDATA for this TBF.
l
15031/2 Number of downlink allocation failures
Name Q3 : dlTBFAllocFailure
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of downlink TBF establishment failures (half
and full duplex transfer), due to lack of radio resources.
Event : Reception of DL--UNITDATA(with a new TLLI), if the number of
MS in transfer is greater or equal to NB_MAX (SPM capacity
limitation set by Nortel Controlled Feature). The PCU tries to
establish the downlink TBF every 5 sec. up to 3 times, so with the
same DL--UNITDATA, the PCU may increment the counter up to 4
times.
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
Note : This counter is also incremented in case of failure of
DL--Preestablishment.
l
15031/3 Number of downlink radio link failures
Name Q3 : dlTBFRadioFailure
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of downlink TBF establishment failures (half
and full duplex), due to radio link failure
l
15033/0 Number of uplink TBFs released
Name Q3 : upTbfReleases
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of UL TBF released in the cell (related to half
duplex or full duplex transfers). This counter counts the normal and
abnormal releases due to loss of communication, OAM event, TS
sharing event.
Event : Release of an UL TBF (related to half duplex or full duplex transfer
and due to normal or abnormal release). No reception of the first PRR.
Resources requested for establishing the uplink TBF rejected by
allocator (because no radio resources available, admission control).
Reception of a first Packet Resource Request (with a new TLLI), if the
number of MS in transfer is greater or equal to the value specified by
the SPM capacity limitation. One phase access contention resolution
fails.
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15033/1 Number of downlink TBFs released
Name Q3 : dnTbfReleases
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of DL TBF released in the cell (related to half
duplex or full duplex transfers). This counter counts the normal and
abnormal releases due to loss of communication, OAM event, TS
sharing event.
Event : Release of a UL TBF (related to half duplex or full duplex transfer and
due to normal or abnormal release). Resources requested for
establishing the downlink TBF rejected by allocator (because no radio
resources available, Admission Control) Reception of
DL--UNITDATA (with a new TLLI), if the number of MS in transfer
is greater or equal to NB_MAXMS (SPM capacity limitation set by
Nortel Controlled feature). The PCU tries to establish the downlink
TBF every 5 sec. up to 3 times, so with the same DL--UNITDATA the
PCU may increment the counter up to 4 times.
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15034/0 Number of Packet Downlink Ack/Nack with Uplink Request
Name Q3 : PDANWithUlReq
cumulativeTimeUpTbf
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of Packet Downlink Ack/Nack messages, with
the Channel Request Description included
Event : This counter is incremented when a Packet Downlink Ack/Nack
message is received, with the Channel Request Description included
Source : recorded by the PCU
Feature : GPRS
Data flows : Refer to Chapter 2
DFD “PCUSN: Abnormal UL TBF Release (Full Duplex):
UP_NASSIGNMAX”
DFD “PCUSN: UL TBF Establishment during DL transfer”
Note : V12.4d counter
l
15034/1 Cumulative number of silver users’ uplink allocations with a
satisfaction rate equal or more than 50% and strictly less than 90%
Name Q3 : upTbfSilverSatisfactBet5090pCent
Value range : 0 to 4294967295
Object : bts
Function : Cumulative number of silver users uplink allocations with a
satisfaction rate equal or more than 50 and strictly less than 90 %.
Refer to section 4.7
Event : Pipe modification. Refer to section 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15036/0 Number of second phase uplink radio link failures
Name Q3 : ulsecondPhaseRadioFailure
Value range : [0 to 4294967295]
Object : bts
Function : Cumulative number of abnormal releases during second phase uplink
TBF establishment (half and full duplex transfer)
Event : This counter is incremented in the following cases:
Non--reception of 6 consecutive non--acknowledgements of the
first Packet Uplink Assignment.
Non--reception of 6 consecutive non--acknowledgments of the
Packet Timeslot Reconfigure sent for the establishment of an
uplink TBF on downlink TBF.
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
l
15038/0 Total number of RLC data blocks sent by the PCU in astalled
window condidtion
Name Q3 : localBusy
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number RLC data blocks sent by the PCU in a stalled
window condition during a downlink transfer on this TDMA.
l
15043/0 Number of retransmitted data blocks by the PCUSN due to
negative acknowledgement
Name Q3 : RequestedRetransmittedDataBlocksDN
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of downlink data blocks retransmitted by the
PCUSN due to negative acknowledgement from the mobile. All
blocks resent due to the Keep Alive feature and Preventive
Retransmission are not counted in this case.
Event : Retransmission of data blocks in NACKed state.
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
Note : The cdl name of the corresponding operational counter is
dnActiveTimeslots.
l
15045/0 Total number of LLC packets reassembled and transmitted to the
LLC Relay
Name Q3 : llcPacketsUp
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of UL LLC frames reassembled by the PCU on
this TDMA.
Event : Reassembly of LLC frames
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15045/1 Total number of LLC packets segmented into RLC data blocks
Name Q3 : llcPacketsDn
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of LLC DL frames segmented by the PCU in
RLC data blocks on this TDMA.
l
15047/0 Total number of uplink RLC control blocks received
Name Q3 : controlBlocksUp
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of RLC/MAC control blocks received in uplink
by the PCU on this TDMA.
Event : This counter is incremented when a TBF is in progress and on
reception of a TRAU frame (without BFI) containing:
an RLC/MAC block including a valid RLC/MAC control block
an RLC/MAC block including an invalid RLC/MAC control block
a valid Stealing Frame (PCA 4--burst access mode)
an invalid Stealing Frame (PCA 4--burst access mode)
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Data flows : Refer to Chapter 2
DFD “PCUSN: UL TBF Establishment”
DFD “PCUSN: UL TBF Establishment during DL transfer”
DFD “PCUSN: Normal UL TBF Release”
DFD “PCUSN: Abnormal UL TBF Release:
UP_NASSIGNMAX”
DFD “PCUSN: Abnormal UL TBF Release (FULL Duplex):
UP_NASSIGNMAX”
DFD “PCUSN: Abnormal UL TBF Release: N3103”
DFD “PCUSN: DL TBF Establisment: MS in StandBy State”
DFD “PCUSN: DL TBF Establisment: MS in Ready State”
DFD “PCUSN: Normal DL TBF Release”
DFD “PCUSN: Abnormal DL TBF Release: lossOfComNN0002”
DFD “PCUSN: Abnormal DL TBF Release (FULL Duplex):
lossOfComNN0002”
DFD “PCUSN: Abnormal DL TBF Release: N3105”
DFD “PCUSN: Abnormal DL TBF Release (FULL Duplex):
N3105”
DFD “PCUSN: Abnormal DL TBF Release:
DN_NASSIGNMAX”
DFD “PCUSN: Cell Update: Packet Transfer”
Note : The term valid/invalid is linked to the protocol integrity. This means
that the block has been correctly received on the radio by the BTS, and
after decoding by the PCU the block is declared valid/invalid
according to the header contents
l
15047/1 Total number of downlink RLC control blocks transmitted
Name Q3 : controlBlocksDn
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of RLC/MAC control block sent by the PCU on
this TDMA.
Event : Sending of a DL RLC control block by a GPRS UL or DL TBF on this
TDMA.
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
Note : This counter does not count the Downlink Dummy Control blocks
sent by the PCU.
l
15048/0 Total number of uplink invalid radio blocks received
Name Q3 : invalidBlocksUp
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of RLC/MAC blocks received with BFI (Bad
Frame Indicator set by the BTS when no correct block has been
decoded on the radio) by the PCU on this TDMA
Event : This counter is incremented when a TBF is in progress and on
reception of a TRAU frame with BFI
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15048/1 Total number of invalid RLC/MAC blocks triggering a protocol
error
Name Q3 : invalidProtocolErrorBlocksUp
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of invalid RLC/MAC blocks triggering a
protocol error, received by the PCU on this TDMA
Source : recorded by the PCU
l
15049/1 Total number of PACKET DOWNLINK ACK/NACK messages
Name Q3 : packetAckNackDn
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of PACKET DOWNLINK ACK/NACK
messages received by the PCU on this TDMA.
Event : This counter is incremented after the reception of a Packet Downlink
Ack/Nack by a GPRS DL TBF on this TDMA.
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
Note : The counter is not incremented if the Packet Downlink Ack/Nack is
received after the release of the downlink TBF (specially up to RTD
after the release of the downlink TBF)
l
15050/0 Total number of RLC/MAC block retransmission requests
Name Q3 : totalRetransmissionRequested
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of UL RLC data blocks badly received by the
PCU on this TDMA and where it requested a retransmission.
Event : Sending of a Packet Uplink Ack/Nack requesting for the
retransmission of UL RCL data blocks
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15051/0 Cumulative uplink rxQual value
Name Q3 : cumulativeUpRxQual
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative value “upRxQual” received by the PCU in each valid
RLC/MAC block on this TDMA. The PCU uses the “assumed value”
X 100 (refer to 3GPP 05.08)
Event : Receipt of a valid TRAU frame by a GPRS UL TBF on this TDMA
(valid means without BFI). Note that the counter is not incremented
upon receipt of a stealing frame.
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
The average is calculated by dividing this counter value by the
nbSamples value.
The counter is not incremented if the RLC/MAC block is received
after the release of the uplink TBF (specially up to RTD after an
abnormal release).
l
15051/1 Cumulative value “RxQual” in Channel Quality Report received
by the PCU in the message Packet Downlink Ack/Nack
Name Q3 : cumulativeDnRxQual
Value range : 0 to 4294967295
Object : transceiver
Function : Cumulative value “RxQual” in Channel Quality Report received by
the PCU in the message Packet Downlink Ack/Nack
Event : This counter is incremented after the reception of a Packet Downlink
Ack/Nack by a TBF on this TDMA containing the Channel Quality
Report set by the mobile
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15052/0 Cumulative value “upRxLev” received by the PCU in each valid
RLC/MAC block on this TDMA
Name Q3 : cumulativeUpRxLev
Value range : 0 to 4294967295
Object : transceiver
Function : Cumulative value “upRxLev” received by the PCU in each valid
RLC/MAC block on this TDMA
Event : Receipt of a valid TRAU frame by a GPRS UL TBF on this TDMA
(valid means without BFI).
Event : This counter is incremented after the reception of a valid RLC/MAC
block by a TBF on this TDMA (valid means without BFI)
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
Note : The counter is not incremented if the RLC/MAC block is received
after the release of the uplink TBF (specially up to RTD after an
abnormal release).
Note : The counter is not incremented upon receipt of a stealing frame.
l
15053/0 Number of sampling for uplink rxQual and uplink rxLev
cumulative values
Name Q3 : nbSamplesUpQuality
Value range : 0 to 4294967295
Object : tranceiver
Function : Cumulative number of valid RLC/MAC blocks received by the PCU
on this TDMA
Event : Receipt of a valid TRAU frame (and different from a stealing frame)
by a TBF on this TDMA (valid means without BFI)
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
The counter is not incremented if the RLC/MAC block is received
after the release of the uplink TBF (specially up to RTD after an
abnormal release)
l
15053/1 Cumulative number of Packet Downlink Ack/Nack messages
received by the PCU on this TDMA, containing the Channel
Quality Report
Name Q3 : nbSamplesDnQuality
Value range : 0 to 4294967295
Object : transceiver
Function : Cumulative number of Packet Downlink Ack/Nack messages
received by the PCU on this TDMA, containing the Channel Quality
Report
Event : This counter is incremented after the reception of a Packet Downlink
Ack/Nack by a TBF on this TDMA, containing the Channel Quality
Report set by the mobile
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15054/0 Total number of data blocks retransmitted downlink
Name Q3 : retransmittedDataBlocksDn
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of RLC data blocks retransmitted by the PCU on
this TDMA. This number includes all the transmission causes (round
trip delay, preventive retransmission, etc.)
Event : Retransmission of a DL RLC data block
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15055/0 Total number of uplink TBFs terminated normally
Name Q3 : tbfNormalReleaseUp
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of normal releases of UL TBFs (related to half
duplex or full duplex transfer).
l
15055/1 Total number of downlink TBFs terminated normally
Name Q3 : tbfNormalReleaseDn
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of normal releases of DL TBFs (related to half
duplex or full duplex transfer).
Event : Normal release of a DL TBF
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
Note : This counter is not relevant in case of CCCH management at BTS.
l
15056/0 Number of TBF abnormal releases due to non receipt of Packet
Resource Request
Name Q3 : noPacketResourceReq
Value range : [0 to 4294967295]
Object : transceiver
Function : Cumulative number of time the PCU has allocated a block for a PRR
(in an IMMEDIATE ASSIGN UL message) and has not received the
PRR from the mobile on this TDMA.
Event : Non receipt of a PRR in the block allocated for this purpose in the
immediate assignment
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15056/1 Total number of PACKET RESOURCE REQUEST messages
received by the PCU from the MS in the second phase of the
2--phase access uplink TBF establishment
Name Q3 : packetResourceRequest
Value range : [0 to 4294967295]
Object : ccch
Function : Cumulative number of PACKET RESOURCE REQUEST messages
received by the PCU in this cell for the second phase of an uplink
establishment.
Event : Receipt of a PRR related to the second phase of an UL TBF
establishment
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15057/0 Number of TBF abnormal releases due to V(Q) and V(A) non
progression
Name Q3 : lossOfComNN002Max
Value range : [0 to 4294967295]
Object : transceiver
Function : Number of abnormal releases due to non progression of V(Q) in
uplink and V(A) in downlink. This means the number of abnormal
releases with a mobile in uplink TBF or downlink TBF because the
received or transmitted window doesn’t progression.
Event : Trigger
For uplink TBF, NN002 consecutive Packet Uplink Ack/Nack is
sent to the mobile without evolution of V(Q).
For downlink TBF, NN002 consecutive Packet Downlink
Ack/Nack (or EGPRS Packet Downlink Ack/Nack) is received
from the mobile without evolution of V(A).
Source : recorded by the PCU
l
15057/2 Number of TBF abnormal releases due to timer NT0001 expiry
Name Q3 : lossOfComNT0001
l
15058/0 Total number of IMMEDIATE ASSIGNMENT messages
generated by the PCU to the MS in the first phase of the 2--phase
access uplink TBF establishment
Name Q3 : upTbfImmediateAssignment
Value range : [0 to 4294967295]
Object : ccch
Function : Cumulative number of IMMEDIATE ASSIGNMENT UPLINK
messages sent by the PCU to establish an UL TBF in this cell. In the
case of CCCH management at the BTS, this counter corresponds to
the cumulative values periodically received from the BTS in the
CCCH information message.
Event : Sending of an IMMEDIATE ASSIGNMENT UPLINK message if
managed by the PCU or receipt of a CCCH information message if
managed by the CCCH at the BTS.
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15058/1 Total number of UL and DL TBF establishment rejected because
the number of MS in transfer is greater or equal ro
NB_MAX_MS
Name Q3 : upTbfImmAssigRejectNoPdch
Value range : [0 to 4294967295]
Object : ccch
Function : Cumulative number of UL and DL TBF establishment rejected
because the number of MS in transfer is greater than or equal to the
value specified by SPM capacity limitation (set by Nortel Controlled
Feature).
SPM capacity limitation is either defined by a max number of MS
reached or by CPU overload.
Event : Reception of a first Packet Resource Request (with a new TLLI), if the
number of MS in transfer is greater than or equal to the value specified
by SPM capacity limitation
Reception of DL--UNITDATA (with a new TLLI), if the number of
MS in transfer is greater or equal to the value specified by the SPM
capacity limitation (set by Nortel Controlled Feature). The PCU will
re--try to establish the downlink TBF every 5 sec up to 3 times, so with
the same DLUNITDATA the PCU may increment the counter up to 4
times.
Source : recorded by the PCU
Note : V14 counter
The PCU will re--try to establish the downlink TBF every 5 sec up to 3
times, so with the same DL--UNITDATA the PCU may increment the
counter up to 4 times.
l
15058/2 Total number of IMMEDIATE ASSIGNMENT messages sent for
a downlink TBF establishment from the PCU to the MS
Name Q3 : dnTbfImmediateAssignment
Value range : [0 to 4294967295]
Object : ccch
Function : Cumulative number of IMMEDIATE ASSIGNMENT DOWNLINK
messages sent by the PCU to establish a DL TBF.
Event : Sending of an IMMEDIATE ASSIGNMENT DOWNLINK message
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15058/3 Number of times a downlink bandwidth, between 1 and 2
timeslots, has been allocated for some mobiles in the cell
Name Q3 : dnPipeBetween11and22kbps
Object : ccch
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
l
15058/4 Number of times a downlink bandwidth, between 2 and 3
timeslots, has been allocated for some mobiles in the cell
Name Q3 : dnPipebetween22and33kbps
Object : ccch
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
l
15059/0 Total number of RACH (Channel Request) messages received in
the PCU in this cell
Name Q3 : channelRequestCcch
Value range : [0 to 4294967295]
Object : ccch
Function : Cumulative number of RACH (Channel Request) received by the
PCU or BTS (in case of CCCH at BTS) in this cell.
In case of CCCH at BTS, this counter corresponds to the cumulative
values periodically received from the BTS in the CCCH information
message (field Number of RACH, for single block and one phase
access.)
Event : Receipt of a Channel Request Message if managed by PCU.
Receipt of a CCCH information message in case of CCCH at BTS.
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
Note : When the CCCH at BTS and the one phase access features are
activated, the one phase access RACH are forwarded to the PCU by
the BTS and the field (RACH for one phase access) in the CCCH
information is not incremented by the BTS.
Note : When CCCH at BTS and one phase access features are activated,
one phase access RACH are forwarded to the PCU by the BTS,
the field ”RACH for one phase access” in CCCH information is
not incremented by the BTS.
l
15060/0 Number of times a downlink bandwidth, of more than 3 timeslots,
has been allocated for some mobiles in the cell
Name Q3 : dnPipeGreater33kbps
Object : ccch
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
l
15060/1 Cumulative number of silver users’ uplink allocations rejected due
to the admittance control
Name Q3 : upTbfSilverRejectedForMinTput
Value range : 0 to 4294967295
Object : CCCH
Function : Cumulative number of silver users’ uplink allocations rejected due to
the admittance control
Event : This counter is incremented after the rejection of a new allocation to a
silver user due to admittance control
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
l
15061/0 Number of times an uplink bandwidth, of less than 1 timeslot, has
been allocated for some mobiles in the cell
Name Q3 : upPipeless11kbps
Object : ccch
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
l
15061/1 Cumulative number of bronze users’ uplink allocations with a
satisfaction rate equal or better than 90%
Name Q3 : upTbfBronzeSatisfactMore90pCent
Value range : 0 to 4294967295
Object : CCCH
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15062/0 Number of times an uplink bandwidth, of more than 1 timeslot,
has been allocated for some mobiles in the cell
Name Q3 : upPipeGreater11kbps
Object : ccch
Function : Cumulative number of times a throughput equal or greater than 11
kbps and strictly less than 22 kbps is reached in uplink direction by a
MS in the cell.
This downlink throughput counter provides a downlink
throughput histogram in the related cell. It represents the
cumulative number of times a throughput between the specified
limits is reached in downlink direction by an MS in the cell.
This uplink throughput counter provides an uplink throughput
histogram in the related cell. Each one represents the cumulative
number of times a throughput between the specified limits is
reached in uplink direction by an MS in the cell.
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
Note : This throughput counters is computed using the number of bytes sent
or received in a pipe (GPRS), and is adapted to the CS used during the
transfer.
Note : Description updated due to introduction of counter
pcuUpPipeGreater22kbps
l
15062/1 Number of times a downlink bandwidth, of less than 1 timeslot,
has been allocated for some mobiles in the cell
Name Q3 : dnPipeLess11kbps
Object : ccch
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
l
15062/2 Cumulative number of silver users’ uplink allocations with a
satisfaction rate strictly less than 50%
Name Q3 : upTbfSilverSatisfactLess50pCent
Value range : 0 to 4294967295
Object : CCCH
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15062/3 Cumulative number of bronze users’ uplink allocations with a
satisfaction rate equal or more than 50% and strictly less than 90%
Name Q3 : upTbfBronzeSatisfactBet5090pCent
Value range : 0 to 4294967295
Object : CCCH
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15062/4 Cumulative number of bronze users’ uplink allocations with a
satisfaction rate strictly less than 50%
Name Q3 : upTbfBronzeSatisfactLess50pCent
Value range : 0 to 4294967295
Object : CCCH
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15062/5 Cumulative number of bronze users’ uplink allocations rejected
due to the admittance control
Name Q3 : upTbfBronzeRejectedForMinTput
Value range : 0 to 4294967295
Object : CCCH
Function : Cumulative number of bronze user’s uplink allocations rejected due
to the admittance control.
Event : This counter is incremented after the rejection of a new allocation to a
bronze user due to admittance control.
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15063/0 Average MPC load
Name Q3 : cpuPBlockUtilAvg
Value range : [0 to 100%]
Object : pBlock
Function : This counter indicates the average CPU load (range 0 to 100%). The
average CPU load is the percentage of time the application has
something to since the last reset of this counter. Note that both the
spooled and operational counters are reset when either the spooled
counters are retrieved or when the operational counters are reset by
the operator.
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
l
15063/2 Max MPC load
Name Q3 : cpuPBlockUtilMax
Value range : [0 to 100%]
Object : pBlock
Function : This counter indicates the maximum CPU load (range 0 to 100%).
Every “durationPeriod” (50 ms +/-- 8 ms (random)) the CPU load is
computed (percentage of time the application has something to do
during the “durationPeriod”). The maximum CPU load is the
maximum value of these computed CPU loads since the last reset of
this counter. Note that both the spooled and the operational counters
are reset when either the spooled counters are retrieved or when the
operational counters are reset by the operator.
Source : recorded by the PCU
Feature : GPRS
Note : V12.4d counter
l
15066/0 Average CPU load
Name Q3 : cpuUtilAvg
Value range : [0 to 100] %
Object : logicalProcessor
Function : This counter indicates an average processor utilization level over a the
specified collection interval. This average is calculated based on one
minute CPU utilization averages.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15066/1 Minimum CPU load
Name Q3 : cpuUtilAvgMin
Value range : [0 to 100] %
Object : logicalProcessor
Function : This counter indicates the minimum processor utilization level over a
specified collection interval. The computing is based on one minute
CPU utilization averages.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15066/2 Maximum CPU load
Name Q3 : cpuUtilAvgMax
Value range : [0 to 100] %
Object : logicalProcessor
Function : This counter indicates the maximum processor utilization level over a
specified collection interval. This is based on one minute CPU
utilization averages.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15067/0 Fast RAM memory capacity
Name Q3 : memoryCapacityFastRam
Value range : [0 to 2147483647]
Object : logicalProcessor
Function : This counter indicates the processor’s memory capacity (in kilobytes)
for fast ram memory.
Event : Refer to “function”
Source : recorded by the PCU
l
15068/0 Average, maximum, and minimum Fast RAM utilization
Name Q3 : memoryUsageAvgFastRam
memoryUsageAvgMaxFastRam
memoryUsageAvgMinFastRam
Value range : [0 to 2147483647]
Object : logicalProcessor
Function : This attribute indicates the processors memory utilization (in
kilobytes) for fast ram memory in the specified collection interval.
This is calculated using 15 second samples.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15068/1 Average, maximum, and minimum Normal RAM utilization
Name Q3 : memoryUsageAvgNormalRam
memoryUsageAvgMaxNormalRam
memoryUsageAvgMinNormalRam
Value range : [0 to 2147483647]
Object : logicalProcessor
Function : This attribute indicates the processor’s memory utilization (in
kilobytes) for normal ram memory in the specified collection interval.
This is calculated using 15 second samples.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15068/2 Average, maximum, and minimum Shared RAM utilization
Name Q3 : memoryUsageAvgSharedRam
memoryUsageAvgMaxSharedRam
memoryUsageAvgMinSharedRam
Value range : [0 to 2147483647]
Object : logicalProcessor
Function : This attribute indicates the processor’s memory utilization (in
kilobytes) for shared ram memory in the specified collection interval.
This is calculated using 15 second samples.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15069/0 Memory capacity of the processor card’s shared message blocks
Name Q3 : sharedMsgBlockCapacity
Value range : [0 to 2147483647]
Object : logicalProcessor
Function : This attribute indicates the processor’s shared message block memory
capacity (in kilobytes).
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15069/1 Average, maximum, and minimum utilization of the processor
card’s shared message blocks
Name Q3 : sharedMsgBlockUsageAvg
sharedMsgBlockUsageAvgMax
sharedMsgBlockUsageAvgMin
Value range : [0 to 2147483647]
Object : logicalProcessor
Function : This attribute indicates the processor’s shared message block memory
utilization (in kilobytes) over a specified collection interval. This is
calculated using 15 second samples.
l
15070/0 Number of bytes received on the link by the Framer
Name Q3 : rxBytes
Value range : [long integer]
Object : framer
Function : Number of bytes received on the link by the Framer in the last
collection interval.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15070/1 Number of bytes transmitted to the link by the Framer
Name Q3 : txBytes
Value range : [long integer]
Object : framer
Function : This counter provides the number of bytes transmitted to the link by
the Framer in the last collection interval. This value could be zero if
the application sends the frames directly to the link.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15071/0 Number of frames received on the link interface by the Framer
Name Q3 : rxFrames
Value range : [long integer]
Object : framer
Function : This counter provides the number of frames received on the link
interface by the Framer in the last collection interval.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15071/1 Number of frames transmitted to the link interface by the
Framer
Name Q3 : txFrames
Value range : [long integer]
Object : framer
Function : This counter provides the number of frames transmitted to the link
interface by the Framer in the last collection interval. This value could
be zero if the application sends the frames directly to the link.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15072 Average total link utilization, based on the computation of the
total number of bytes received on the link
Name Q3 : rxTotalLinkUtil
Value range : [0 to 100]
Object : framer
Function : This counter provides the average total link utilization computed
based on the total number of bytes received on the link in the last
collection interval.
Event : Refer to “function”
Source : recorded by the PCU
Feature : GPRS (SV407 - V12)
Note : V12.4b and c counter
l
15073/0 Cumulative number of BSSGP PAGING PS PDU received on the
SPM and related to this PCM link
Name Q3 : psPaging
Value range : 0 to 4294967295
Object : pcmCircuit
Function : Cumulative number of BSSGP PAGING PS PDU received on the
SPM and related to this PCM link (received either on BVCI0 or BVCI
PTP).
The PS PAGING received on BVCI0 and broadcast by the frame
relay to the SPM cards are only counted on the master SPM which
manages the message (note that when the feature “paging load
distribution” is deactivated all the psPaging are counted on the
master SPM).
The PS PAGING received on BVCI PTP are counted on the
corresponding SPM which manages the message.
Event : This counter is incremented upon reception of a BSSGP PS PAGING
PDU, by any BVC, from the SGSN.
Source : recorded by the PCU
Feature : GPRS -- 26257 Paging load distribution on several LAPD
Note : V14 counter
l
15073/1 Cumulative number of BSSGP PAGING CS PDU received on the
SPM and related to this PCM link
Name Q3 : csPaging
Value range : 0 to 4294967295
Object : pcmCircuit
Function : Cumulative number of BSSGP PAGING CS PDU received on the
SPM and related to this PCM link (received either on BVCI0 or BVCI
PTP).
The CS PAGING received on BVCI0 and broadcast by the frame
relay to the SPM cards are only counted on the SPM which
manages the message (note that when the feature “paging load
distribution” is deactivated all the csPaging are counted on the
master SPM).
The CS PAGING received on BVCI PTP are counted on the
corresponding SPM which manages the message.
Event : This counter is incremented upon reception of a BSSGP CS PAGING
PDU, by any BVC, from the SGSN.
Source : recorded by the PCU
Name Q3 : pcuDyAgprsNbTimeslotsCum
Function : Number of iteration samples for pcuDyAgprsNbTimeslotsCum
Name Q3 : pcuDyAgprsNbTimeslotsNbs
Function : Cumulative number of Agprs timeslots allocated in the cell by the
BSC.
This corresponds to the formula: sum (dyAgprsNbTs<i>). The value
dyAgprsNbTs<i> is the number of Agprs TS allocated in the cell at the
<i>th sample.
Value range : 0 to 4294967295
Object : bts
Function : Cumulative number of Agprs timeslots allocated in the cell by the
BSC.
This corresponds to the formula: sum (dyAgprsNbTs<i>). The value
dyAgprsNbTs<i> is the number of Agprs TS allocated in the cell at the
<i>th sample.
Note: When the cell is set as the most or least loaded cell several times in
a row (to exchange jYeser TS following main TS), the load
criterion is not computed each time. In that case the counter is not
incremented.
l
15078/3 Cumulative number of silver users’ downlink allocations rejected
due to the admittance control
Name Q3 : dnTbfSilverRejectedForMinTput
Value range : 0 to 4294967295
Object : bts
Function : Cumulative number of silver users’ downlink allocations rejected due
to the admittance control.
Event : This counter is incremented after the rejection of a new allocation to a
silver user due to admittance control.
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
Note : Reject counters with minimum throughput for gold, silver, and bronze
by indicating that these counters are not incremented in case of
DL--Preestablishment.
l
15079/0 Cumulative number of bronze users’ downlink allocations with a
satisfaction rate equal or better than 90%
Name Q3 : dnTbfBronzeSatisfactMore90pCent
Value range : 0 to 4294967295
Object : bts
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15079/1 Cumulative number of bronze users’ downlink allocations with a
satisfaction rate equal or more than 50% and strictly less than 90%
Name Q3 : dnTbfBronzeSatisfactBet5090pCent
Value range : 0 to 4294967295
Object : bts
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15079/2 Cumulative number of bronze users’ downlink allocations with a
satisfaction rate strictly less than 50%
Name Q3 : dnTbfBronzeSatisfactLess50pCent
Value range : 0 to 4294967295
Object : bts
Function : Refer to Paragraph 4.7
Event : Refer to Paragraph 4.7
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
l
15079/3 Cumulative number of bronze users’ downlink allocations rejected
due to the admittance control
Name Q3 : dnTbfBronzeRejectedForMinTput
Value range : 0 to 4294967295
Object : bts
Function : Cumulative number of bronze users’ downlink allocations rejected
due to the admittance control.
Event : This counter is incremented after the rejection of a new allocation to a
bronze user due to admittance control.
Source : recorded by the PCU
Feature : GPRS
Note : V14 counter
Note : Reject counters with minimum throughput for gold, silver, and bronze
by indicating that these counters are not incremented in case of
DL--Preestablishment.
l
15100/0 Spare counter, 0 by default
Name Q3 : pcuEdgeTdma15100s0
Value range : 0 to 4294967295
Object : TDMA
Function : NA
Event : NA
Source : recorded by the PCU
Feature : EDGE traffic management
Note : V14.4 counter
l
15101/0 Cumulative number of EGPRS RLC data blocks received by
the PCU on a TDMA.
Name Q3 : pcuEdgeDataBlocksReceivedUp
Value range : 0 to 4294967295
Object : TDMA
Function : Cumulative number of EGPRS RLC data blocks received by the PCU
on this TDMA.
Event : Reception of an EGPRS UL TBF in progress of a TRAU frame
without BFI
- a valid RLC data block in sequence received for the first time
-- a valid RLC data block in sequence already received
- a valid RLC data block out of sequence
-- an invalid RLC data block
Source : recorded by the PCU
Feature : GPRS
Note : In case of receipt of an EGPRS Header Stealing Frame, this counter is
not incremented.
l
15102/0 Average, cumulative, and sampling number of 8PSK_BEP
(assumed value) derived from the 8PSK_MEAN_BEP received
from an MS in this TDMA in the EGPRS BEP Link Quality
Measurements (8PSK_MEAN_BEP).
Name Q3 : pcuEdgeDnAvg8PskMeanBep
pcuEdgeDnCum8PskMeanBep
Function : Cumulative value of the 8PSK_BEP (assumed value) derived from
the 8PSK_MEAN_BEP received from a MS in this TDMA in the
EGPRS BEP Link Quality Measurements (8PSK_MEAN_BEP).
Measurement result: BEP in % * 100
Note : MEAN_BEP is calculated and filtered in a linear scale but mapped to
a logarithmic scale for reporting as defined in 3GPP 05.08, so for the
processing of the average value, the log10 (actual BEP) is used (the
value is between 0.60 and 3.60).
Note : The MEAN_BEP is used to derive the BEP (assumed value) reported
in the counter.
Event : Reception of an EGPRS Packet Downlink Ack/Nack by a EGPRS DL
TBF on this TDMA, containing a 8PSK_MEAN_BEP value set in the
EGPRS BEP link quality measurements.
Note : The EGPRS BEP link quality measurement is optional and may not be
reported by MS (the counter is not incremented).
Note : The 8PSK_MEAN_BEP may not be included in the EGPRS BEP link
quality measurements (the counter is not incremented).
Name Q3 : pcuEdgeDnNbs8PskMeanBep
Function : Number of values of the 8PSK_MEAN_BEP received from an MS in
this TDMA in the EGPRS BEP Link Quality Measurements
(8PSK_MEAN_BEP).
Event : Reception of an EGPRS Packet Downlink Ack/Nack by a EGPRS DL
TBF on this TDMA, containing a 8PSK_MEAN_BEP value set in the
EGPRS BEP link quality measurements.
Value range : 0 to 4294967295
Object : TDMA
Source : recorded by the PCU
Feature : GPRS TBF establishment improvement - one phase access (15015)
Note : V14.4 counter
l
15103/0 Average, cumulative, and sampling number of GMSK_BEP
(assumed value) derived from the GMSK_MEAN_BEP received
from an MS in this TDMA in the EGPRS BEP Link Quality
Measurements (GMSK_MEAN_BEP).
Name Q3 : pcuEdgeDnAvgGmskMeanBep
pcuEdgeDnCumGmskMeanBep
Value range : 0 to 4294967295
Object : TDMA
Function : This counter has 3 possible functions and can be used to determine the
average or cumulative value, or the sampling number of the
GMSK_BEP derived from the GMSK_MEAN_BEP received from a
MS in this TDMA in the EGPRS BEP Link Quality Measurements
(GMSK_MEAN_BEP).
Note : MEAN_BEP is calculated and filtered in a linear scale but mapped to
a logarithmic scale for reporting as defined in 3GPP 05.08, so for the
processing of the average value, the log10 (actual BEP) is used (the
value is between 0.60 and 3.60).
Note : The MEAN_BEP is used to derive the BEP (assumed value)
reported in the counter.
Event : Reception of an EGPRS Packet Downlink Ack/Nack by an EGPRS
DL TBF on this TDMA, containing a GSMK_MEAN_BEP value set
in the EGPRS BEP link quality measurements.
Note : The EGPRS BEP link quality measurement is optional and may not be
reported by MS (the counter is not incremented).
Note : The GMSK_MEAN_BEP may not be included in the EGPRS BEP
link quality measurements (the counter is not incremented).
Name Q3 : pcuEdgeDnNbsGmskMeanBep
Function : Number of values of the GMSK_MEAN_BEP received from an MS
in this TDMA in the EGPRS BEP Link Quality Measurements
(GMSK_MEAN_BEP).
Event : Reception of an EGPRS Packet Downlink Ack/Nack by an EGPRS
DL TBF on this TDMA, containing a GSMK_MEAN_BEP value set
in the EGPRS BEP link quality measurements.
Value range : 0 to 4294967295
Object : TDMA
Source : recorded by the PCU
l
15105/0 Spare counter, 0 by default
Name Q3 : pcuEdgeTdma15105s0
Value range : 0 to 4294967295
Object : TDMA
Function : NA
Event : NA
Source : recorded by the PCU
Feature : GPRS TBF establishment improvement -- one phase access (15015)
Note : V15 counter
l
15106/0 Spare coumter, 0 by default
Name Q3 : pcuEdgeTdma15106s0
Value range : 0 to 4294967295
Object : TDMA
Function : NA
Event : NA
Source : recorded by the PCU
Feature : GPRS TBF establishment improvement -- one phase access (15015)
Note : V15 counter
l
15107/0 Spare counter, 0 by default
Name Q3 : pcuEdgeTdma15107s0
Value range : 0 to 4294967295
Object : TDMA
Function : NA
Event : NA
Source : recorded by the PCU
Feature : GPRS TBF establishment improvement -- one phase access (15015)
Note : V15 counter
l
15108/0 Cumulated number of radio blocks sent by the PCU
Name Q3 : pcuEdgeTdma15108s0
Value range : 0 to 4294967295
Object : TDMA
Function : Cumulated number of radio blocks sent by the PCU on this TDMA for
downlink pipes in verbose state (data blocks + control blocks)
Event : Downlink pipe closure
Source : recorded by the PCU
Feature : GPRS TBF establishment improvement - one phase access (15015)
Note : V15 counter
l
15110/0 Total number of TRAU data blocks and control blocks (GPRS or
EGPRS) snet on the Agprs Main channels in the DL direction
Name Q3 : pcuAgprsMainNbofBlocksDn
Value range : 0 to 4294967295
Object : bts
Function : Total number of TRAU EDGE data blocks sent on the Agprs Main
channels in the DL direction.
Event : This counter is incremented after a TRAU data block or control block
sent on the Agprs Main Channel by a GPRS or EGPRS TBF.
Source : recorded by the PCU
Feature : Data backhaul evolution (19174)
Note : V15 counter
l
15111/0 Average, cumulative, and sampling number of EGPRS TBF
downgraded in GPRS
Name Q3 : pcuEdgeDowngradedTbfAvg
pcuEdgeDowngradedTbf
pcuEdgeDowngradedTbfNbs
Value range : 0 to 4294967295
Object : bts
Function : These counters are used to determine the average or cumulative value,
or the sampling number of EGPRS TBF downgraded in GPRS.
Event : In the UL direction, when a Packet Resource Request including an
EDGE request is received by PCU.
In the DL direction, when a first DL unit data including an EDGE
request is received for a MS with no ongoing TBF (note that the
counter is incremented for each attempt to establish the DL TBF).
In those cases, and if the PCU allocates the MS on a GPRS TDMA, the
counter is incremented.
Source : recorded by the PCU
Event : An RLC EDGE data block is received for the first time (i.e. fresh
block) on a pipe by a EGPRS UL TBF.
Precise
incrementation conditions :
If there is loss of communication, the duration counters are not
incremented.
The pcuEdgeUpAvgUsefulDataPerCell represents the average
throughput at RLC level and cell level for every EGPRS transfer.
pcuEdgeUpAvgUsefulDataPerCell = ratio between
pcuEdgeUpCumUsefulDataPerCell and
pcuEdgeUpNbsUsefulDataPerCell
T0 = Time of the first valid TRAU frame received in uplink for that
mobile (i.e. without BFI)
T1 = Time of the reception of the last block with CV=0 (when all
the blocks have been correctly received). The counter is equal to
T1--T0+1
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
Note : If there is loss of communication, the duration counters are not
incremented.
l
15113/0 Average, cumulative, and sampling size in bytes of all the RLC
EDGE data blocks sent for the first time (i.e. fresh block)
Name Q3 : pcuEdgeDnAvgUsefulDataPerCell
pcuEdgeDnCumUsefulDataPerCell
pcuEdgeDnNbsUsefulDataPerCell
Value range : 0 to 4294967295
Object : bts
Function : This counter has 3 possible functions and can be used to determine the
average, cumulative, or sampling size in bytes of all the RLC EDGE
data blocks sent for the first time on a pipe.
The pcuEdgeUpAvgUsefulDataPerCell represents the average
throughput at RLC level and cell level for every EGPRS transfer.
– pcuEdgeUpAvgUsefulDataPerCell = ratio between
pcuEdgeUpCumUsefulDataPerCell and
pcuEdgeUpNbsUsefulDataPerCell
– pcuEdgeUpCumUsefulDataPerCell = Cumulated size in bytes of
all the EGPRS data blocks received for the first time (i.e. fresh
block) on a pipe.
– pcuEdgeUpNbsUsefulDataPerCell = Cumulated time in multiples
of 20 ms where the MS is in EGPRS UL data transfer.
T0 = Time of the first valid TRAU frame received in uplink for that
mobile (i.e. without BFI)
T1 = Time of the reception of the last block with CV=0 (when all the
blocks have been correctly received). The counter is equal to
T1--T0+1
Event : An RLC EDGE data block is sent for the first time (i.e. fresh block) on
a pipe by a EGPRS DL TBF.
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
4
15114/0 Spare counter, 0 by default
Name Q3 : pcuEdgeCell15114s0
Value range : 0 to 4294967295
Object : bts
Function : NA
Event : NA
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
Event : This counter is incremented after a TRAU data block is sent on the
Agprs Joker Channel by a GPRS or EGPRS DL TBF.
Source : recorded by the PCU
Feature : Data backhaul evolution (19174)
Note : V15 counter
l
15120/0 Spare counter, 0 by default
Name Q3 : pcuEdgeCell15120s0
Value range : 0 to 4294967295
Object : bts
Function : NA
Event : NA
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15121/0 Spare counter, 0 by default
Name Q3 : pcuEdgeCell15121s0
Value range : 0 to 4294967295
Object : bts
Function : NA
Event : NA
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15122/0 Number of EGPRS TBF establishment requests.
Name Q3 : pcuEdgeTbfEstReq
Value range : 0 to 4294967295
Object : bts
Function : Cumulative number of EGPRS TBF establishment requests.
Event : In the UL direction, when a Packet Resource Request including an
EDGE request is received by PCU.
In the DL direction, when a first DL unit data including an EDGE
request is received for an MS with no on--going TBF (note that the
counter is incremented for each attempt to establish the DL TBF).
Precise
incrementation conditions :
The counter is incremented for each attempt to establish the DL
TBF.
The counter is not incremented during a full duplex TBF
establishment.
The counter is not incremented if EDGE is not activated in the cell
(through the flag EGPRSServices).
The counter is not incremented when The value specified by the
SPM capacity limitation is reached.
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
Note : The counter is not incremented during a Full--Duplex establishment.
Note : The counter is not incremented if EDGE is not activated in the cell
(through the flag EGPRSServices).
Note : Note also that the value of this counter cannot be linked the value of
counters upTbfReleases and dnTbfReleases.
l
15123/0 Cumulated time in multiple of 20ms where the MS is in EDGE UL
data transfer.
Name Q3 : pcuEdgeUpUsefulDataDurationPerCell
Value range : 0 to 4294967295
Object : bts
Function : Cumulative time in multiples of 20 ms where the MS is in EDGE UL
data transfer.
Event : NA
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15126/0 Spare counter, 0 by default
Name Q3 : pcuEdgeCell15126s0
Value range : 0 to 4294967295
Object : bts
Function : NA
Event : NA
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15127/0 Total number of TRAU EDGE data blocks sent on the Agprs Main
channels in the UL direction
Name Q3 : pcuAgprsMainNbofBlocksUp
Value range : 0 to 4294967295
Object : bts
Function : Number of TRAU data blocks or control blocks (GPRS or EGPRS)
received on the Agprs Main TS in the UL direction.
This counter is equal to:
up data block EDGE + up control block EDGE + invalid block up
EDGE + up data block GPRS + up control block GPRS + up invalid
block up GPRS
Note : A TRAU frame is invalid if:
It is received with a BFI (Bad Frame Indicator set by the BTS when
no correct block has been decoded on the radio).
Then when a TRAU frame is valid, the contents can be invalid
(depending on the type of the frame).
Note : A stealing frame is invalid if:
One of its fields (class, type, length, ta, rach info) is erroneous.
the access burst type (8 or 11 bits format) used is inconsistent with
the Access Burst Type parameter received in message CELL
AVAILABLE or CELL BROADCAST INFO MODIFY.
Event : This counter is incremented after a TRAU data block or control block
is received on the Agprs Main TS by a GPRS or EGPRS TBF.
Source : recorded by the PCU
Feature : Data backhaul evolution (19174)
Note : V15 counter
Note : The UL blocks (data or control) are counted when allocated to that
mobile (by USF, polling).
The first PRR are also counted (with or without CCCH@BTS).
l
15128/0 Total number of TRAU EDGE data blocks sent on the Agprs Joker
channels in the UL direction
Name Q3 : pcuAgprsJokerNbofBlocksUp
Value range : 0 to 4294967295
Object : bts
Function : Total number of TRAU EDGE data blocks (GPRS or EGPRS)
received on the Agprs Joker TS in the UL direction.
Note : Unexpected blocks are NOT counted.
Event : This counter is incremented after a TRAU data block is received on
the Agprs Joker TS by a GPRS or EGPRS UL TBF.
Source : recorded by the PCU
Feature : Data backhaul evolution (19174).
Note : V15 counter
l
15129/0 Number of periods of 20ms when missing jokers in the DL direction
to reach the MCS targeted by the Link Adaptation
Name Q3 : pcuLackAbisJokerTSNbs
Function : Number of periods of 20 ms when there was missing Abis Jokers TS in
the DL direction to reach the MCS targeted by the Link Adaptation.
l
15132/0 Number of 1/2 EDGE RLC Data Blocks transmitted in MCS2 by
PCU in the DL direction
Name Q3 : pcuEdgeDnTransmittedMcs2
Value range : 0 to 4294967295
Object : TDMA
Function : Number of 1/2 EDGE RLC Data Blocks that are transmitted in MCS2
by PCU in the DL direction.
Event : An EDGE DL RLC Data Block sent by PCU in MCS2 (for the first
time (i.e. fresh block) or restransmitted).
Precise
incrementation conditions :
The counter is only incremented by 1 unit when the MCS2 data
block is a re--segmented data block (this means it is half a RLC data
block).
When one EDGE DL radio block is sent by the PCU in the DL
direction using MCS2, the counter is incremented by 2 units (1
RLC data block per radio block).
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15133/0 Number of 1/2 EDGE RLC Data Blocks transmitted in MCS3 by
PCU in the DL direction
Name Q3 : pcuEdgeDnTransmittedMcs3
Value range : 0 to 4294967295
Object : TDMA
Function : Number of 1/2 EDGE RLC Data Blocks transmitted in MCS3 by PCU
in the DL direction.
Event : An EDGE DL radio data block sent by PCU in MCS3 (for the first
time (i.e. fresh block) or restransmitted).
Precise
incrementation conditions :
The counter is only incremented by 1 unit when the MCS3 data
block is a re-- - segmented data block (this means it is half a RLC
data block).
When one EDGE DL radio block is sent by the PCU in the DL
direction using MCS3, the counter is incremented by 2 units (1
RLC data block per radio block).
l
15135/0 Number of 1/2 EDGE RLC Data Blocks transmitted in MCS5 by
PCU in the DL direction
Name Q3 : pcuEdgeDnTransmittedMcs5
Value range : 0 to 4294967295
Object : TDMA
Function : Number of 1/2 EDGE RLC Data Blocks transmitted in MCS5 by
PCU in the DL direction.
Event : An EDGE DL RLC Data Block sent by PCU in MCS5 (for the first
time (i.e. fresh block) or restransmitted).
Precise
incrementation conditions :
When one EDGE DL radio block is sent by the PCU in the DL
direction using MCS5, the counter is incremented by 2 units (1 RLC
data block per radio data block).
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15136/0 Number of 1/2 EDGE RLC Data Blocks transmitted in MCS6 by
PCU in the DL direction
Name Q3 : pcuEdgeDnTransmittedMcs6
Value range : 0 to 4294967295
Object : TDMA
Function : Number of 1/2 EDGE RLC Data Blocks transmitted in MCS6 by
PCU in the DL direction.
Event : An EDGE DL RLC Data Block sent by PCU in MCS6 (for the first
time (i.e. fresh block) or restransmitted).
Precise
incrementation conditions :
When one EDGE DL radio block is sent by the PCU in the DL
direction using MCS6, the counter is incremented by 2 units (1 RLC
data block per radio data block).
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15137/0 Number of 1/2 EDGE RLC Data Blocks transmitted in MCS7 by
PCU in the DL direction
Name Q3 : pcuEdgeDnTransmittedMcs7
Value range : 0 to 4294967295
Object : bts
Function : Number of 1/2 EDGE RLC Data Blocks transmitted in MCS7 by PCU
in the DL direction.
Event : An EDGE DL RLC Data Block sent by PCU in MCS7 (for the first
time (i.e. fresh block) or restransmitted).
Precise
incrementation conditions :
When one EDGE DL radio block is sent by the PCU in the DL
direction using MCS7, the counter is incremented by 4 units (2 RLC
data blocks per radio data block).
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15138/0 Number of 1/2 EDGE RLC Data Blocks transmitted in MCS8 by
PCU in the DL direction.
Name Q3 : pcuEdgeDnTransmittedMcs8
Value range : 0 to 4294967295
Object : TDMA
Function : Number of 1/2 EDGE RLC Data Blocks transmitted in MCS8 by PCU
in the DL direction.
Event : An EDGE DL RLC Data Block sent by PCU in MCS8 (for the first
time (i.e. fresh block) or restransmitted).
Precise
incrementation conditions :
When one EDGE DL radio block is sent by the PCU in the DL
direction using MCS8, the counter is incremented by 4 units (2 RLC
data blocks per radio data block).
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15139/0 Number of 1/2 EDGE RLC Data Blocks transmitted in MCS9 by
PCU in the DL direction
Name Q3 : pcuEdgeDnTransmittedMcs9
Value range : 0 to 4294967295
Object : TDMA
Function : Number of 1/2 EDGE RLC Data Blocks transmitted in MCS9 by PCU
in the DL direction.
Event : An EDGE DL RLC Data Block sent by PCU in MCS9 (for the first
time (i.e. fresh block) or restransmitted).
Precise
incrementation conditions :
When one EDGE DL radio block is sent by the PCU in the DL
direction using MCS9, the counter is incremented by 4 units (2 RLC
data blocks per radio data block).
Source : recorded by the PCU
Feature : EDGE traffic management (20231) - one phase access (15015)
Note : V15 counter
l
15142/0 Number of 1/2 EDGE radio data blocks that were commanded by
the Link Adaptation in MCS2 AND sent in MCS2 by PCU in the DL
direction AND NACK by the MS.
Name Q3 : pcuEdgeMcs2RequestRetransDataBlockDn
Value range : 0 to 4294967295
Object : TDMA
Function : When an E--GPRS PACKET DOWNLINK ACK/NACK is received
by PCU, the list of NACK blocks to be repeated is updated. The
counter is incremented by 2 units for each of these repeated blocks that
were targeted in MCS2 in the previous transmission.
Event : An EDGE Radio Data Block targeted by LA in MCS2 and sent in
MCS2 (for the first time (i.e. fresh block) or retransmitted) is NACK
by MS in PDAN.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : EDGE link adaptation (20219)
Note : 1 to 7 applicable to pcuEdgeMcs9RequestRetransDataBlockDn
(15149) also apply to this counter.
l
15143/0 Number of 1/2 EDGE radio data blocks that were commanded by
the Link Adaptation in MCS3 AND sent in MCS3 by PCU in the DL
direction AND NACK by the MS.
Name Q3 : pcuEdgeMcs3RequestRetransDataBlockDn
Value range : 0 to 4294967295
Object : TDMA
Function : When an E--GPRS PACKET DOWNLINK ACK/NACK is received
by PCU, the list of NACK blocks to be repeated is updated. The
counter is incremented by 2 units for each of these repeated blocks that
were targeted in MCS3 in the previous transmission.
Event : An EDGE DL radio data block targeted by LA in MCS3 and sent in
MCS3 (for the first time (i.e. fresh block) or retransmitted) is NACK
by MS in PDAN.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : EDGE link adaptation (20219)
Note : V15 counter
l
15147/0 Number of 1/2 EDGE radio data blocks that were commanded by
the Link Adaptation in MCS7 AND sent in MCS7 by PCU in the DL
direction AND NACK by the MS.
Name Q3 : pcuEdgeMcs7RequestRetransDataBlockDn
Value range : 0 to 4294967295
Object : TDMA
Function : When an E--GPRS PACKET DOWNLINK ACK/NACK is received
by PCU, the list of NACK blocks to be repeated is updated. The
counter is incremented by 2 units for each of these repeated blocks that
were targeted in MCS7 in the previous transmission.
Event : An EDGE DL RLC Data Block targeted by LA in MCS7 and sent in
MCS7 (for the first time (i.e. fresh block) or retransmitted) is NACK
by MS in PDAN.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : EDGE link adaptation (20219)
Note : V15 counter
Note: 1 to 8 applicable to pcuEdgeMcs9RequestRetransDataBlockDn (15149)
also apply to this counter.
l
15148/0 Number of 1/2 EDGE radio data blocks that were commanded by
the Link Adaptation in MCS8 AND sent in MCS8 by PCU in the DL
direction AND NACK by the MS.
Name Q3 : pcuEdgeMcs8RequestRetransDataBlockDn
Value range : 0 to 4294967295
Object : TDMA
Function : When an E--GPRS PACKET DOWNLINK ACK/NACK is received
by PCU, the list of NACK blocks to be repeated is updated. The
counter is incremented by 2 units for each of these repeated blocks that
were targeted in MCS8 in the previous transmission.
l
15149/0 Number of 1/2 EDGE radio data blocks that were commanded by
the Link Adaptation in MCS9 AND sent in MCS9 by PCU in the DL
direction AND NACK by the MS.
Name Q3 : pcuEdgeMcs9RequestRetransDataBlockDn
Value range : 0 to 4294967295
Object : TDMA
Function : When an E--GPRS PACKET DOWNLINK ACK/NACK is received
by PCU, the list of NACK blocks to be repeated is updated. The
counter is incremented by 2 units for each of these repeated blocks that
were targeted in MCS9 in the previous transmission.
Event : An EDGE DL RLC Data Block targeted by LA in MCS9 and sent in
MCS9 (for the first time (i.e. fresh block) or retransmitted) is NACK
by MS in PDAN.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
l
15152/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS2 AND sent in MCS2 by PCU in the DL
direction.
Name Q3 : pcuEdgeLADnTargetedTransmittedMcs2
Value range : 0 to 4294967295
Object : TDMA
Function : When one EDGE radio data block is sent by PCU in the DL direction
using the MCS2, commanded by the nominal Link Adaptation tables,
the counter is incremented by 2 units.
Event : An EDGE DL radio data block targeted by LA in MCS2 and sent in
MCS2 (for the first time (i.e. fresh block) or retransmitted).
Unit : 1/2 EDGE radio data block
Function : Number of 1/2 EDGE RLC Data Blocks transmitted in MCS2 by PCU
in the DL direction.
l
15153/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS3 AND sent in MCS3 by PCU in the DL
direction.
Name Q3 : pcuEdgeLADnTargetedTransmittedMcs3
Value range : 0 to 4294967295
Object : TDMA
Function : When one EDGE radio data block is sent by PCU in the DL direction
using the MCS3, commanded by the nominal Link Adaptation tables,
the counter is incremented by 2 units.
Event : An EDGE DL radio data block targeted by LA in MCS3 and sent in
MCS3 (for the first time (i.e. fresh block) or retransmitted).
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : EDGE link adaptation (20219)
Note : V15 counter
Note : Notes 1 to 6 applicable to pcuEdgeLADnTargetedTransmittedMcs9
(15159/0) also apply to this counter.
l
15155/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS5 AND sent in MCS5 by PCU in the DL
direction.
Name Q3 : pcuEdgeLADnTargetedTransmittedMcs5
Value range : 0 to 4294967295
Object : TDMA
Function : When one EDGE radio data block is sent by PCU in the DL direction
using the MCS5, commanded by the nominal Link Adaptation tables,
the counter is incremented by 2 units.
l
15177/0 Number of 1/2 EDGE radio data blocks that were commanded by
the Link Adaptation in MCS7 AND sent in MCS7 by MS in the UL
direction AND badly received by BTS.
Name Q3 : pcuEdgeMcs7RequestRetransDataBlockUp
Value range : 0 to 4294967295
Object : TDMA
Function : When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a Block is badly received by
PCU (E--GPRS Header with cause ”Bad CRC on the radio” or a
Semi--frame or a TRAU Data frame with Frame Validity set to ’0’ on
both BSN), and if this Radio Data Block was targeted in MCS7, the
counter is incremented by 2 units.
When a Block is partially received (”Semi--frame with cause 1st or
2nd block lost or a TRAU Data frame with one of the 2 Frame Validity
set to ’0’), and if this Radio Data Block was targeted in MCS7, the
counter is incremented by 1 unit.
Event : Block badly received by PCU while targeted in MCS7 by link
adaptation.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : 20219 (EDGE link adaptation)
Note : V15 counter
Note : Notes 1 to 7 applicable to
pcuEdgeMcs9RequestRetransDataBlockUp (15179/0) also apply to
this counter.
l
15178/0 Number of 1/2 EDGE Radio Data Blocks that were commanded by
the Link Adaptation in MCS8 AND sent in MCS8 by MS in the UL
direction AND badly received by BTS.
Name Q3 : pcuEdgeMcs8RequestRetransDataBlockUp
Value range : 0 to 4294967295
Object : TDMA
Function : When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a Block is badly received by
PCU (E--GPRS Header with cause ”Bad CRC on the radio” or a
Semi--frame or a TRAU Data frame with Frame Validity set to ’0’ on
both BSN), and if this Radio Data Block was targeted in MCS8, the
counter is incremented by 2 units.
When a Block is partially received (”Semi--frame with cause 1st or
2nd block lost or a TRAU Data frame with one of the 2 Frame Validity
set to ’0’), and if this Radio Data Block was targeted in MCS8, the
counter is incremented by 1 unit.
Event : Block badly received by PCU while targeted in MCS8 by link
adaptation.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : 20219 (EDGE link adaptation)
Note : V15 counter
Note : Notes 1 to 7 applicable to
pcuEdgeMcs9RequestRetransDataBlockUp (15179/0) also apply to
this counter.
l
15179/0 Number of 1/2 EDGE Radio Data Blocks that were commanded by
the Link Adaptation in MCS9 AND sent in MCS9 by MS in the UL
direction AND badly received by BTS.
Name Q3 : pcuEdgeMcs9RequestRetransDataBlockUp
Value range : 0 to 4294967295
Object : TDMA
Function : Number of 1/2 EDGE Radio Data Blocks that were commanded by
the Link Adaptation in MCS9 AND sent in MCS9 by MS in the UL
direction AND badly received by BTS.
When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a Block is badly received by
PCU (E--GPRS Header with cause ”Bad CRC on the radio” or a
Semi--frame or a TRAU Data frame with Frame Validity set to ’0’ on
both BSN), and if this Radio Data Block was targeted in MCS9, the
counter is incremented by 2 units.
When a Block is partially received (”Semi--frame with cause 1st or
2nd block lost or a TRAU Data frame with one of the 2 Frame Validity
set to ’0’), and if this Radio Data Block was targeted in MCS9, the
counter is incremented by 1 unit.
Event : Block badly received by PCU while targeted in MCS9 by link
adaptation.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
l
15182/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS2 AND sent in MCS2 by MS in the UL
direction.
Name Q3 : pcuEdgeLAUpTargetedTransmittedMcs2
Value range : 0 to 4294967295
Object : TDMA
Function : When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a data block (with frame
validity bits = 0 or 1) or a “Semi--Frame” or an “EGPRS--Header” or a
TRAU Data frame with Frame Validity set to ’0’ is received by PCU,
and if the MCS is equal to the MCS commanded by LA, the counter is
increased by 2 units.
l
15183/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS3 AND sent in MCS3 by MS in the UL
direction.
Name Q3 : pcuEdgeLAUpTargetedTransmittedMcs3
Value range : 0 to 4294967295
Object : TDMA
Function : When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a data block (with frame
validity bits = 0 or 1) or a ”Semi--Frame” or an “EGPRS--Header” or a
TRAU Data frame with Frame Validity set to ’0’ is received by PCU,
and if the MCS is equal to the MCS commanded by LA, the counter is
increased by 2 units.
Event : Transmission by the MS of a data block in MCS3 when MCS3 is the
coding scheme commanded by the LA.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : EDGE link adaptation (20219)
Note : V15 counter
Note: Notes 1 to 5 on pcuEdgeLAUpTargetedTransmittedMcs9 (15189/0) also
apply to this counter.
l
15185/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS5 AND sent in MCS5 by MS in the UL
direction.
Name Q3 : pcuEdgeLAUpTargetedTransmittedMcs5
Value range : 0 to 4294967295
Object : TDMA
Function : When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a data block (with frame
validity bits = 0 or 1) or a ”Semi--Frame” or an ”EGPRS--Header” or a
TRAU Data frame with Frame Validity set to ’0’ is received by PCU,
and if the MCS is equal to the MCS commanded by LA, the counter is
increased by 2 units.
Event : Transmission by the MS of a data block in MCS5 when MCS5 is the
coding scheme commanded by the LA.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : EDGE link adaptation (20219)
Note : V15 counter
Note : Notes 1 to 5 on pcuEdgeLAUpTargetedTransmittedMcs9 (15189/0)
also apply to this counter.
l
15186/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS6 AND sent in MCS6 by MS in the UL
direction.
Name Q3 : pcuEdgeLAUpTargetedTransmittedMcs6
Value range : 0 to 4294967295
Object : TDMA
Function : When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a data block (with frame
validity bits = 0 or 1) or a “Semi--Frame” or an “EGPRS--Header” or a
TRAU Data frame with Frame Validity set to ’0’ is received by PCU,
and if the MCS is equal to the MCS commanded by LA, the counter is
increased by 2 units.
l
15187/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS7 AND sent in MCS7 by MS in the UL
direction.
Name Q3 : pcuEdgeLAUpTargetedTransmittedMcs7
Value range : 0 to 4294967295
Object : TDMA
Function : When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a data block (with frame
validity bits = 0 or 1) or a ”Semi--Frame” or an “EGPRS--Header” or a
TRAU Data frame with Frame Validity set to ’0’ is received by PCU,
and if the MCS is equal to the MCS commanded by LA, the counter is
increased by 2 units.
Event : Transmission by the MS of a data block in MCS7 when MCS7 is the
coding scheme commanded by the LA.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : EDGE link adaptation (20219)
Note : V15 counter
Note: Notes 1 to 5 on pcuEdgeLAUpTargetedTransmittedMcs9 (15189/0) also
apply to this counter.
l
15188/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS8 AND sent in MCS8 by MS in the UL
direction.
Name Q3 : pcuEdgeLAUpTargetedTransmittedMcs8
Value range : 0 to 4294967295
Object : TDMA
Function : When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a data block (with frame
validity bits = 0 or 1) or a “Semi--Frame” or an “EGPRS--Header” or a
TRAU Data frame with Frame Validity set to ’0’ is received by PCU,
and if the MCS is equal to the MCS commanded by LA, the counter is
increased by 2 units.
Event : Transmission by the MS of a data block in MCS8 when MCS8 is the
coding scheme commanded by the LA.
Unit : 1/2 EDGE radio data block
Source : recorded by the PCU
Feature : EDGE link adaptation (20219)
Note : V15 counter
Note: Notes 1 to 5 on pcuEdgeLAUpTargetedTransmittedMcs9 (15189/0) also
apply to this counter.
l
15189/0 Number of 1/2 EDGE radio data blocks that are commanded by the
Link Adaptation in MCS9 AND sent in MCS9 by MS in the UL
direction.
Name Q3 : pcuEdgeLAUpTargetedTransmittedMcs9
Value range : 0 to 4294967295
Object : TDMA
Function : When an USF is scheduled for a MS in the DL direction, the PCU
internally associates that block with the MCS commanded by the Link
Adaptation in the UL direction. When a data block (with frame
validity bits = 0 or 1) or a ”Semi--Frame” or an ”EGPRS--Header” or a
TRAU Data frame with Frame Validity set to ’0’ is received by PCU,
and if the MCS is equal to the MCS commanded by LA, the counter is
increased by 2 units.
l
15190/0 Cumulative number of “one phase access” RACH (Channel
Request) received by the PCU in this cell.
Name Q3 : pcuChannelRequestOnePhase
Value range : 0 to 4294967295
Object : CCCH
Function : Cumulative number of “one phase Channel Request” received at the
PCU level.
This counter is only incremented when the PCU receives a channel
request one phase.
Event : Receipt of a Channel Request message, one phase by PCU.
Source : recorded by the PCU
Name Q3 : pcuUpThroughputNbs
Function : Cumulated time in multiple of 20 ms where the MS is in GPRS UL
data transfer.
T0 = Time of the first valid TRAU frame received in uplink for that
mobile (i.e. without BFI)
T1 = Time of the reception of the last block with CV=0 (when all
the blocks have been correctly received). The counter is equal to
T1--T0+1
The pcuUpThroughputAvg represents the average throughput at
RLC level and cell level for every GPRS transfer.
pcuUpThroughputAvg = ratio between pcuUpThroughputCum
and pcuUpThroughputNbs
pcuUpThroughputCum = Cumulated size in bytes of all the GPRS
data blocks received for the first time (i.e. fresh block) on a pipe.
pcuUpThroughputNbs = Cumulated time in multiples of 20 ms
where the MS is in GPRS UL data transfer.
Event : A RLC GPRS data block is received for the first time (that is fresh
block) on a pipe by a GPRS UL TBF.
Name Q3 : pcuUpThroughputCum
Function : Cumulated size in bytes of all the RLC GPRS data blocks received for
the first time (i.e. fresh block) on a pipe.
Event : A RLC GPRS data block is received for the first time (that is fresh
block) on a pipe by a GPRS UL TBF.
Value range : 0..4294967295
Object : bts
Source : recorded by the PCU
Counters Function
15007/0 Number of octets discarded, because the number of received PDUs exceeds
the bucket size
15007/1 Cumulated size in bytes of all the GPRS RLC data blocks sent for the first
time (i.e. fresh block) on a pipe
15007/1 Cumulated time in multiple of 20ms where the MS is in GPRS DL data
transfer.
TO = Time of the first block sent in downlink for that mobile
T1 = Time of the last FRESH or NACKED block
T2 = Time of the PDAN which acknowledged all the downlink blocks
The counter is equal to T1--T0+1=T2-- T0--(RTD + RRBP)+1
15075/1 Cumulative number of Agprs timeslots allocated in the cell by the BSC.
This correspond to the formula: sum (dyAgprsNbTs<i>). The value
dyAgprsNbTs<i> is the number of Agprs TS allocated in the cell at the <i>th
sample.
15075/1 Number of iteration samples for pcuDyAgprsNbTimeslotsCum.
15075/1 This counter is no more relevant at the PCU level; it is always set to 0.
15076/0 Cumulative value of Agprs load criterion for the related cell.
The average value is calculated since the last reset PCU.
15076/0 Number of iteration samples for pcuDyAgprsLoadCriterionCum.
15076/0 This counter is no more relevant at the PCU level; it is always set to 0.
15100/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum
15101/0 Cumulative number of EGPRS RLC data blocks received by the PCU on this
TDMA.
15102/0 Cumulative value of the 8PSK_BEP derived from the 8PSK_MEAN_BEP
received from a MS in this TDMA in the EGPRS BEP Link Quality
Measurements (8PSK_MEAN_BEP).
15102/0 Number of values of the 8PSK_MEAN_BEP received from a MS in this
TDMA in the EGPRS BEP Link Quality Measurements (8PSK_MEAN_BEP).
15103/0 Cumulative value of the GMSK_BEP derived from the
GMSK_MEAN_BEP received from a MS in this TDMA in
the EGPRS BEP Link Quality Measurements
(GMSK_MEAN_BEP).
15103/0 Number of values of the GMSK_MEAN_BEP received from a MS in this
TDMA in the EGPRS BEP Link Quality Measurements
(GMSK_MEAN_BEP).
Counters Function
15104/0 Cumulated value of the assumed BEP received by the PCU in
each EGPRS RLC data block on this TDMA.
15104/0 Number of MEAN_BEP values received by the PCU in each EGPRS RLC
data block on this TDMA.
15105/0 Spare counter, 0 by default.
15106/0 Spare counter, 0 by default.
15107/0 Spare counter, 0 by default.
15108/0 Spare counter, 0 by default.
15109/0 Spare counter, 0 by default.
15110/0 Total number of TRAU EDGE data blocks sent on the Agprs Main channels in
the DL direction.
15111/0 Number of EGPRS TBF downgraded in GPRS.
15112/0 Accumulative size in octets of all the RLC EDGE data blocks received for the
first time on a pipe.
15113/0 Accumulated size in octets of all the RLC EDGE data blocks
sent for the first time on a pipe.
15114/0 Spare counter, 0 by default.
15115/0 Spare counter, 0 by default.
15116/0 Spare counter, 0 by default.
15117/0 Spare counter, 0 by default.
15118/0 Cumulative number of Agprs Joker TS allocated to the cell by the BSC.
15118/0 Minimum number of Agprs Joker TS allocated to the cell by the BSC.
15118/0 Maximum number of Agprs Joker TS allocated to the cell by the BSC.
15119/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of TRAU data blocks sent to th Agprs Joker Channel
15120/0 Spare counter, 0 by default.
15121/0 Spare counter, 0 by default.
15122/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EGPRS TBF establishment requests.
15123/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of times in multiples of 20ms where the pipes for UL EGPRS TBF
are in “verbose” state.
15124/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Accumulative
times in multiples of 20ms where the pipes for DL EGPRS TBF are in
“verbose” state.
15125/0 Spare counter, 0 by default.
15126/0 Spare counter, 0 by default.
Counters Function
15127/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Total number
of TRAU EDGE data blocks sent on the Agprs Main channels in the UL
direction.
15128/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Total number
of TRAU EDGE data blocks sent on the Agprs Joker channels in the UL
direction.
15129/0 Number of period of 20ms when there were missing Agprs Jokers TS in the
DL direction to reach the MCS targeted by the Link Adaptation.
15129/0 Number of Missing Agprs Jokers TS in the DL direction to reach the MCS
targeted by the Link adaptation.
15132/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS2 by PCU in the DL
direction.
15133/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS3 by PCU in the DL
direction.
15135/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS5 by PCU in the DL
direction.
15136/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS6 by PCU in the DL
direction.
15137/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS7 by PCU in the DL
direction.
15138/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS8 by PCU in the DL
direction.
15139/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS9 by PCU in the DL
direction.
15142/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS2 by PCU in the DL
direction.
15143/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS3 by PCU in the DL
direction.
15145/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS5 by PCU in the DL
direction.
Counters Function
15146/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS6 by PCU in the DL
direction.
15147/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS7 by PCU in the DL
direction.
15148/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS8 by PCU in the DL
direction.
15149/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS9 by PCU in the DL
direction.
15152/0 Number of 1/2 EDGE radio data blocks that are commanded by the Link
Adaptation in MCS2 AND sent in MCS2 by PCU in the DL direction.
15153/0 Number of 1/2 EDGE radio data blocks that are commanded by the Link
Adaptation in MCS3 AND sent in MCS3 by PCU in the DL direction.
15155/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS5 by PCU in the DL
direction.
15156/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS6 by PCU in the DL
direction.
15157/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS7 by PCU in the DL
direction.
15158/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS8 by PCU in the DL
direction.
15159/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS9 by PCU in the DL
direction.
15162/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks that are transmitted in MCS2 by MS in
the UL direction.
15163/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks that are transmitted in MCS3 by MS in
the UL direction.
15165/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks that are transmitted in MCS5 by MS in
the UL direction.
Counters Function
15166/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS6 by MS in the UL
direction.
15167/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS7 by MS in the UL
direction.
15168/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum
Cumulative number of EDGE RLC Data Blocks transmitted in MCS8 by MS
in the UL direction.
15169/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS9 by MS in the UL
direction.
15172/0 Number of 1/2 EDGE radio data blocks that were commanded by the Link
Adaptation in MCS2 AND sent in MCS2 by MS in the UL direction AND badly
received by BTS.
15173/0 Number of 1/2 EDGE radio data blocks that were commanded by the Link
Adaptation in MCS3 AND sent in MCS3 by MS in the UL direction AND badly
received by BTS.
15175/0 Number of 1/2 EDGE radio data blocks that were commanded by the Link
Adaptation in MCS5 AND sent in MCS5 by MS in the UL direction AND badly
received by BTS.
15176/0 Number of 1/2 EDGE radio data blocks that were commanded by the Link
Adaptation in MCS6 AND sent in MCS6 by MS in the UL direction AND badly
received by BTS.
15177/0 Number of 1/2 EDGE radio data blocks that were commanded by the Link
Adaptation in MCS7 AND sent in MCS7 by MS in the UL direction AND badly
received by BTS.
15178/0 Number of 1/2 EDGE radio data blocks that were commanded by the Link
Adaptation in MCS8 AND sent in MCS8 by MS in the UL direction AND badly
received by BTS.
15179/0 Number of 1/2 EDGE radio data blocks that were commanded by the Link
Adaptation in MCS9 AND sent in MCS9 by MS in the UL direction AND badly
received by BTS.
15182/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS2 by MS in the UL
direction.
15183/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS3 by MS in the UL
direction.
15185/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS5 by MS in the UL
direction.
Counters Function
15186/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS6 by MS in the UL
direction.
15187/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS7 by MS in the UL
direction.
15188/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS8 by MS in the UL
direction.
15189/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of EDGE RLC Data Blocks transmitted in MCS9 by MS in the UL
direction.
15190/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of “one phase Channel Request” received at the PCU level.
15191/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of “Immediate Assignment Uplink” messages sent by the PCU to
establish a one phase access UL TBF in this cell.
15192/0 Number of iteration samples for pcuDyAgprsNbTimeslotsCum|Cumulative
number of failures of the contention resolution procedure in case of one
phase access.
15193/0 Cumulated size in bytes of all the RLC GPRS data blocks received for the
first time (i.e. fresh block) on a pipe.
15193/0 Cumulated time in multiples of 20ms where the MS is in GPRS UL data
transfer.
15194/0 Cumulative number of times a throughput equal or greater than 22 kbps is
reached in uplink direction by a MS in the cell.
15195/0 Cumulative number of DL TBF pre--established and effectively used for the
transmission of a DL--UNIDATA received from the SGSN.
A
abisCongestionTimeMoy/Max/Cum/Ech, 5--472
abisInputIByte, 5--466
abisInputIFrame, 5--465
abisInputUiByte, 5--465
abisInputUiFrame, 5--464
abisLevel1ErrorsBadFrame, 5--7
abisLevel1ErrorsCrcError, 5--7
abisLevel1ErrorsLostAlign, 5--8
abisLevel2ErrorBadLg, 5--471
abisLevel2ErrorBadRxNr, 5--469
abisLevel2ErrorReqOutState, 5--469
abisLevel2ErrorRxDm0, 5--468
abisLevel2ErrorRxDm1, 5--466
abisLevel2ErrorRxFrmr, 5--470
abisLevel2ErrorRxNoImpl, 5--470
abisLevel2ErrorRxSabme, 5--468
abisLevel2ErrorRxSup1, 5--466
abisLevel2ErrorRxUa0, 5--467
abisLevel2ErrorRxUa1, 5--467
abisLevel2ErrorTxNDisc, 5--469
abisLevel2ErrorTxNSabme, 5--468
abisOutputIByte, 5--465
abisOutputIFrame, 5--464
abisOutputUiByte, 5--465
abisOutputUiFrame, 5--464
abisTrauFrameCorrected, 5--342
abisTrauFrameDlReceived, 5--342
abisTrauFrameMuted, 5--343
abisUnavailabilityTimeCum, 5--471
abisUnavailabilityTimeEch, 5--471
abisUnavailabilityTimeMax, 5--471
abisUnavailabilityTimeMoy, 5--471
ackDnTbfEstablishment, 5--637
agprsResumeNack, 5--45
agprsResumeRequest, 5--45
agprsSuspendNack, 5--44
agprsSuspendRequestMessages, 5--43
agprsSuspendRequestProcedures, 5--43
amrCellLoadStateOverevaluated, 5--73
amrCellLoadStateUnderevaluated, 5--73
amrDownlinkNoDataFrames, 5--98
amrFilteredBusyTchRatioMoy/Max/Cum/Ech, 5--72
amrFrBadSpeechFramesCodec102, 5--94
amrFrBadSpeechFramesCodec102TrZone, 5--94
amrFrBadSpeechFramesCodec475, 5--93
amrFrBadSpeechFramesCodec475TrZone, 5--93
amrFrBadSpeechFramesCodec59, 5--94
amrFrBadSpeechFramesCodec59TrZone, 5--94
amrFrBadSpeechFramesCodec67, 5--94
amrFrBadSpeechFramesCodec67TrZone, 5--94
amrFrDownlinkCodec102, 5--92
amrFrDownlinkCodec102TrZone, 5--92
amrFrDownlinkCodec475, 5--90
amrFrDownlinkCodec475TrZone, 5--90
amrFrDownlinkCodec59, 5--91
amrFrDownlinkCodec59TrZone, 5--91
amrFrDownlinkCodec67, 5--91
amrFrDownlinkCodec67TrZone, 5--91
amrFrHoExecutionIntraCellTch, 5--80
amrFrHoRequestIntraCellTch, 5--79
amrFrHoRequestOutgoingTch, 5--78
amrFrHoSuccessIntraCellTch, 5--81
amrFrHoSuccessOutgoingTch, 5--37
amrFrSpeechAlgoFallBack, 5--32
amrFrTchAllocated, 5--56
amrFrTchAllocatedTrZone, 5--56
amrFrTchAssignFailure, 5--58
amrFrTchConnectionDurationMoy/Max/Cum/Ech, 5--57
amrFrTchConnectionDurationTrZoneMoy/Max/Cum/Ech, 5--57
amrFrTchStdAveragedUsedMoy/Max/Cum/Ech, 5--56
amrFrTchStdAveragedUsedCellMoy/Max/Cum/Ech, 5--71
amrFrTchStdAveragedUsedTrZoneMoy/Max/Cum/Ech, 5--56
amrFrTchSuccessfullyAssigned, 5--58
amrFrToHrHoExecutionIntraCellTch, 5--80
amrFrToHrHoRequestIntraCellTch, 5--79
amrFrToHrHoSuccessIntraCellTch, 5--81
amrFrUplinkCodec102, 5--89
amrFrUplinkCodec102TrZone, 5--89
amrFrUplinkCodec475, 5--88
amrFrUplinkCodec475TrZone, 5--88
amrFrUplinkCodec59, 5--88
amrFrUplinkCodec59TrZone, 5--88
amrFrUplinkCodec67, 5--88
amrFrUplinkCodec67TrZone, 5--88
amrFrValidSpeechFramesCodec102, 5--96
amrFrValidSpeechFramesCodec102TrZone, 5--96
amrFrValidSpeechFramesCodec475, 5--95
amrFrValidSpeechFramesCodec475TrZone, 5--95
amrFrValidSpeechFramesCodec59, 5--95
amrFrValidSpeechFramesCodec59TrZone, 5--95
amrFrValidSpeechFramesCodec67, 5--95
amrFrValidSpeechFramesCodec67TrZone, 5--95
amrHrBadSpeechFramesCodec475, 5--96
amrHrBadSpeechFramesCodec475TrZone, 5--96
amrHrBadSpeechFramesCodec59, 5--96
amrHrBadSpeechFramesCodec59TrZone, 5--96
amrHrBadSpeechFramesCodec67, 5--97
amrHrBadSpeechFramesCodec67TrZone, 5--97
amrHrDownlinkCodec475, 5--92
amrHrDownlinkCodec475TrZone, 5--92
amrHrDownlinkCodec59, 5--92
amrHrDownlinkCodec59TrZone, 5--92
amrHrDownlinkCodec67, 5--93
amrHrDownlinkCodec67TrZone, 5--93
amrHrHoRequestOutgoingTch, 5--78
amrHrHoSuccessOutgoingTch, 5--37
amrHrModeDuration, 5--71
amrHrTchAssignFailure, 5--59
amrHrTchConnectionDurationMoy/Max/Cum/Ech, 5--57
amrHrTchConnectionDurationTrZoneMoy/Max/Cum/Ech, 5--57
amrHrTchSuccessfullyAssigned, 5--58
amrHrToFrHoExecutionIntraCellTch, 5--80
amrHrToFrHoRequestIntraCellTch, 5--79
amrHrToFrHoSuccessIntraCellTch, 5--81
amrHrUplinkCodec475, 5--89
amrHrUplinkCodec475TrZone, 5--89
amrHrUplinkCodec59, 5--90
amrHrUplinkCodec59TrZone, 5--90
amrHrUplinkCodec67, 5--90
amrHrUplinkCodec67TrZone, 5--90
amrHrValidSpeechFramesCodec475, 5--97
amrHrValidSpeechFramesCodec475TrZone, 5--97
amrHrValidSpeechFramesCodec59, 5--97
amrHrValidSpeechFramesCodec59TrZone, 5--97
amrHrValidSpeechFramesCodec67, 5--98
amrHrValidSpeechFramesCodec67TrZone, 5--98
amrQualityFrDownHoRequiredTch, 5--75
amrQualityFrUpHoRequiredTch, 5--74
amrQualityHrDownHoRequiredTch, 5--77
amrQualityHrUpHoRequiredTch, 5--77
amrReversalPhaseFailure, 5--102
amrUplinkNoDataFrames, 5--98
aNonTransparentDown, 5--266
aNonTransparentUp, 5--265
aOutputMessage, raw permanent, 5--138
asciCallInitiationVbs, 5--345
asciCallInitiationVgcs, 5--346
asciInbandNotification, 5--347
asciInbandPaging, 5--346
asciPreemptionPerformed, 5--347
asciTalkerHandoverVbs, 5--396
asciTalkerHandoverVgcs, 5--396
assignFailure, 5--117
assignRequestAintOthers, 5--434
assignRequestAintSdcchToTchChannel, 5--434
assignRequestOthers, 5--433
assignRequestSdcchToTchChannel, 5--432
assignToOtherBandOrZone, 5--395, 5--457, 5--458
aTransparentDown, 5--264
aTransparentUp, 5--263
attemptedTchFrSeizureInclHo, 5--486
attemptedTchFrSeizureNotInclHo, 5--485
attemptedTchFrSeizures, 5--116
attemptedTchFrSeizures8W, 5--445
attemptedTchFrSeizuresMsDualb, 5--340
averageDLRxLev, 5--516
averageDLRxQual, 5--517
averageULRxLev, 5--517
averageULRxQual, 5--518
B
bscAllocationFailureTchFrSeizureInclHo, 5--519
bscAttemptedTchFrSeizureInclHo, 5--519
bscAttemptedTchFrSeizureNotInclHo, 5--519
bscClearRequestTraffic, 5--520
bscHoExecutionIncomingSdcch, 5--530, 5--531
bscOtherThanPaging, 5--513
bscPagingResponse, synthetic permanent, 5--512
bscSdcchAllocated, 5--515
bscSdcchAveragedUsedMax, synthetic permanent bsc, 5--510
bscSdcchAveragedUsedMoy, synthetic permanent bsc, 5--510
bscTchFrAllocatedOverflowAllocation, 5--515
bscTchFrAllocatedPrimoAllocation, 5--515
bscTchFrAllocatedTchAllocation, 5--516
bscTchFrAveragedUsedOverflowAllocationMoy, 5--511
bscTchFrAveragedUsedPrimoAllocationMoy, 5--511
bscTchFrAveragedUsedTchAllocationMoy, 5--512
bsPowerDecControl, 5--402
bsPowerDecControlAmrFr, 5--64
bsPowerDecControlAmrHr, 5--68
bsPowerIncControl, 5--401
bsPowerIncControlAmrFr, 5--63
bsPowerIncControlAmrHr, 5--68
btsOverloadDuration, 5--340
burstToTransmit, 5--38
bvcFlowControlRequests, 5--581
C
callDropTrafficRatio, 5--523
capacityFrToHrHoRequiredTch, 5--75
capacityHoFiltered, 5--71
cardSynthLoadCpue0Moy/Max/Cum/Ech, 5--27
cardSynthLoadCpue1Moy/Max/Cum/Ech, 5--27
cardSynthLoadCpue2Moy/Max/Cum/Ech, 5--27
cardSynthLoadCpumMoy/Max/Cum/Ech, 5--27
cardSynthLoadSicdxMoy/Max/Cum/Ech, 5--27
cellLoadTch, 5--531
cellSdcchResourceFailureRatio, 5--522
cellTchResourceFailureRatio, 5--522
cgOverloadRejectedOpChannelReqCg0/1/2, 5--22
cgOverloadRejectedOpEstablishIndCg0/1/2, 5--23
cgOverloadRejectedOpPageReqBtsCg0/1/2, 5--25
cgOverloadRejectedOpPageReqCg0/1/2, 5--21
cgOverloadRejectedOpHoReqCg0/1/2, 5--24
chainStandbyResponse, 5--12
chainStandbyUpdate, 5--12
channelActivateSignallingFullRate, 5--316
channelActivateSpeechAmrFr, 5--55
channelActivateSpeechAmrHr, 5--54
channelActivateSpeechEnhancedFullRate, 5--254
channelActivateSpeechFullRate, 5--253
channelActivateTchFrDataNT12000, 5--335
channelActivateTchFrDataNT14500, 5--336
channelActivateTchFrDataNT6000, 5--334
channelActivateTchFrDataT1200, 5--324
channelActivateTchFrDataT14400, 5--328
channelActivateTchFrDataT16, 5--322
channelActivateTchFrDataT2400, 5--325
channelActivateTchFrDataT4800, 5--326
channelActivateTchFrDataT600, 5--323
channelActivateTchFrDataT9600, 5--327
channelActivateTchHrDataNT6000, 5--337
channelActivateTchHrDataT16, 5--329
channelActivateTchHrDataT2400, 5--332
ChannelActivateTchHrDataT4800, 5--333
channelActivateTchHrDataT600, 5--330, 5--331
channelActTchFrDataNT, 5--338
channelActTchFrDataT, 5--337
channelActTchHrDataNT, 5--339
channelActTchHrDataT, 5--338
channelAveragedIdlePerInterfBand0, 5--301
channelAveragedIdlePerInterfBand1, 5--302
channelAveragedIdlePerInterfBand2, 5--302
channelAveragedIdlePerInterfBand3, 5--303
channelAveragedIdlePerInterfBand4, 5--304
channelIdleLevelCum, 5--461
channelIdleLevelEch, 5--461
channelIdleLevelMax, 5--461
channelIdleLevelMoy, 5--461
channelRequest, 5--353
channelRequestCause000, 5--234
channelRequestCause001, 5--234
channelRequestCause010, 5--235
channelRequestCause011, 5--236
channelRequestCause100, 5--236
channelRequestCause101, 5--237
channelRequestCause110, 5--238
channelRequestCause111, 5--238
channelRequestCcch, 5--619
channelRequestExtended, 5--321
CIUplinkAmrFr, 5--64
CIUplinkAmrFrTrZone, 5--64
CIUplinkAmrHr, 5--69
CIUplinkAmrHrTrZone, 5--69
CIUplinkFr, 5--59
CIUplinkFrTrZone, 5--59
clearRequestTraffic, 5--486
cmDatabaseUsed, 5--546
cmDatabaseUsedCum, 5--546
cmDatabaseUsedEch, 5--546
cmLogUsed, 5--547
cmLogUsedCum, 5--547
cmLogUsedEch, 5--547
connectionDurationSdcch, 5--274
connectionDurationSdcchTrZoneCum, 5--276
connectionDurationSdcchTrZoneEch, 5--276
connectionDurationSdcchTrZoneMax, 5--276
connectionDurationSdcchTrZoneMoy, 5--276
connectionDurationTchTrZoneCum, 5--271
connectionDurationTchTrZoneEch, 5--271
connectionDurationTchTrZoneMax, 5--271
connectionDurationTchTrZoneMoy, 5--271
controlBlocksDn, 5--605
controlBlocksUp, 5--604
cpue0LoadRatio, 5--528
cpue1LoadRatio, 5--528
cpuPBlockUtilAvg, 5--623
cpuPBlockUtilMax, 5--624
cpuUtilAvg, 5--624
cpuUtilAvgMax, 5--625
cpuUtilAvgMin, 5--625
csPaging, 5--632
CsPagingOnCcch, 5--583
CsPagingOnPACCH, 5--584
configuredTimeslots, 5--600
cumulativeDnRxLev, 5--600
cumulativeDnRxQual, 5--608
cumulativeTimeDnTbf, 5--599
cumulativeTimeUpTbf, 5--598
cumulativeUpActiveTimeslots, 5--600
cumulativeUpRxLev, 5--609
cumulativeUpRxQual, 5--608
D
dataBlocksDn, 5--603
dataBlocksUp, 5--602
dataNtRateFbTcbConfNotAllowed, 5--233
dataNtRateFbTcbResLack, 5--233
dataNtRateFbTchConfNotAllowed, 5--348
dataNtRateFbTchResLack, 5--348
decAmrFrDownModif, 5--100
decAmrFrDownModifTrZone, 5--100
decAmrFrUpModif, 5--99
decAmrFrUpModifTrZone, 5--99
decAmrHrDownModif, 5--102
decAmrHrDownModifTrZone, 5--102
decAmrHrUpModif, 5--101
decAmrHrUpModifTrZone, 5--101
deleteIndication, 5--399
directedRetryUnsuccessNoBts, 5--305
dlMutedAbisTrauFrameRate, 5--518
dnMultiSlotAllocations1, 5--593
dnMultiSlotAllocations2, 5--594
dnMultiSlotAllocations3, 5--594
dnMultiSlotAllocations4, 5--595
dnMultiSlotRequest1, 5--590
dnMultiSlotRequest2, 5--591
dnMultiSlotRequest3, 5--592
dnMultiSlotRequest4, 5--593
dnPipeBetween11and22kbps, 5--618
dnPipebetween22and33kbps, 5--619
dnPipeGreater33kbps, 5--620
dnPipeLess11kbps, 5--622
dnTbfBronzeRejectedForMinTput, 5--642
dnTbfBronzeSatisfactBet5090pCent, 5--642
dnTbfBronzeSatisfactLess50pCent, 5--642
dnTbfBronzeSatisfactMore90pCent, 5--641
dnTbfGoldRejectedForMinTput, 5--639
dnTbfGoldSatisfactBet5090pCent, 5--639
dnTbfGoldSatisfactLess50pCent, 5--639
dnTbfGoldSatisfactMore90pCent, 5--638
dnTbfImmediateAssignment, 5--618
dnTbfReleases, 5--598
dnTbfSilverRejectedForMinTput, 5--641
dnTbfSilverSatisfactBet5090pCent, 5--640
dnTbfSilverSatisfactLess50pCent, 5--640
dnTbfSilverSatisfactMore90pCent, 5--640
downgradedL1mModeOnClassmark, 5--444
downlinkPowerCtrlMaxSdcchCum, 5--272
downlinkPowerCtrlMaxSdcchEch, 5--272
downlinkPowerCtrlMaxSdcchMax, 5--272
downlinkPowerCtrlMaxSdcchMoy, 5--272
downlinkPowerCtrlMaxTchMoy/Max/Cum/Ech, 5--255
downlinkPowerCtrlMaxTchAmrFrMoy/Max/Cum/Ech, 5--60
downlinkPowerCtrlMaxTchAmrHrMoy/Max/Cum/Ech, 5--65
dyAgprsAvgLoadCriterionCum, 5--636
dyAgprsMaxLoadCriterion, 5--638
dyAgprsMaxNbTimeslots, 5--636
dyAgprsMinNbTimeslots, 5--635
dyAgprsNbModif, 5--633
E
e3OverloadRejectedOpChannelReq, 5--33
e3OverloadRejectedOpEstablishInd, 5--33
e3OverloadRejectedOpHoReq, 5--34
e3OverloadRejectedOpPagingReq, 5--33
e3OverloadRejectedOpPagingReqReject, 5--34
e3OverloadRejectedOpSmsCb, 5--35
e3PrDiskCnOmuLdRMoy/Max/Cum/Ech, 5--51
e3PrDiskCnOmuLdWMoy/Max/Cum/Ech, 5--51
e3PrDiskCnOmuMdRMoy/Max/Cum/Ech, 5--53
e3PrDiskCnOmuMdWMoy/Max/Cum/Ecch, 5--52
e3PrMemCnOmuSbcMemMoy/Max/Cum/Ech, 5--48
e3PrMemCnOmuSbcSwapMoy/Max/Cum/Ech, 5--49
e3PrMemCnTmuPmcMoy/Max/Cum/Ech, 5--50
e3PrMemCnTmuSbcMoy/Max/Cum/Ech, 5--49
ecuActivation, 5--344
estabIndicSignalling, 5--354
estabIndicSignallingEmergency, 5--249
estabIndicSignallingEmergency8W, 5--452
estabIndicSignallingEmergency8w, 5--354
estabIndicSignallingImsiDetach, 5--248
estabIndicSignallingLocUpdate, 5--246
estabIndicSignallingMoc, 5--248
estabIndicSignallingPagingRes, 5--245
estabIndicSignallingPiggybacked, 5--354
estabIndicSignallingReEstab, 5--247
estabIndicSignallingShortMsg, 5--250
estabIndicSignallingSuppService, 5--251
estabIndicSigPhase1, 5--252
estabIndicSigPhase2, 5--253
estabIndicSigPhase28W, 5--452
F
faultyTrxNoBcch, 5--529
fmDatabaseUsed, 5--547
fmDatabaseUsedCum, 5--547
fmDatabaseUsedEch, 5--547
fmLogUsed, 5--547
fmLogUsedCum, 5--547
fmLogUsedEch, 5--547
ftamFtiDelete, 5--565
ftamFtiDeleteConf, 5--565
ftamFtiDir, 5--565
ftamFtiDirConf, 5--565
ftamFtiGet, 5--564
ftamFtiGetConf, 5--564
ftamFtiPut, 5--564
ftamFtiPutConf, 5--564
ftamFtiRename, 5--566
ftamFtiRenameConf, 5--566
fullDuplexTbfEstablishment, 5--595
G
gprsImmAssRejectedSicd, 5--9
gprsPagingRejectedSicd, 5--10
gprsPreemption, 5--412
gprsPreemptionNack, 5--412
gprsRachRejectedSicd, 5--8
H
hoBtsRejected, 5--383
hoExecutionIncoming, 5--530
hoExecutionIncomingInterBss, raw permanent, 5--124
hoExecutionIncomingInterBssSdcch, raw permanent, 5--164
hoExecutionIncomingIntraBss, raw permanent, 5--124
hoExecutionIncomingIntraBssSdcch, raw permanent, 5--163
hoExecutionIncomingIntraBssTchMsDualb, 5--392
hoExecutionIncomingSdcch, 5--530
hoExecutionIntraBts, raw permanent, 5--129
hoExecutionIntraBtsMsDualb, 5--394
hoExecutionIntraBtsSdcch, raw permanent, 5--168
hoExecutionOutgoing, 5--529
hoExecutionOutgoingEbandEbandMsDualb, 5--390
hoExecutionOutgoingEbandMbandMsDualb, 5--391
hoExecutionOutgoingInterBss, raw permanent, 5--120
hoExecutionOutgoingInterBssForDirectedRetry, raw permanent, 5--30
hoExecutionOutgoingInterBssSdcch, raw permanent, 5--161
hoExecutionOutgoingIntraBss, raw permanent, 5--120
hoExecutionOutgoingIntraBssForDirectedRetry, raw permanent, 5--29
hoExecutionOutgoingIntraBssSdcch, raw permanent, 5--160
hoExecutionOutgoingMbandEbandMsDualb, 5--388
hoExecutionOutgoingMbandMbandMsDualb, 5--389
hoExecutionOutgoingSdcch, 5--529
hoFailureIncomingInterBssSdcchChannelActivateNack, 5--365
hoFailureIncomingInterBssSdcchHoNotAllowed, 5--365
hoFailureIncomingInterBssSdcchRadioLack, 5--364
hoFailureIncomingInterBssSdcchTchnAckTimerExp, 5--366
hoFailureIncomingInterBssSdcchTerrestLack, 5--365
hoFailureIncomingInterBssTchChannelActivateNack, 5--363
hoFailureIncomingInterBssTchCICIncompatible, 5--364
hoFailureIncomingInterBssTchHoNotAllowed, 5--363
hoFailureIncomingInterBssTchRadioLack, 5--362
hoFailureIncomingInterBssTchTchnAckTimerExp, 5--363
hoFailureIncomingInterBssTchTerrestLack, 5--362
hoFailureIncomingIntraBssSdcchChannelActivateNack, 5--361
hoFailureIncomingIntraBssSdcchHoNotAllowed, 5--361
hoFailureIncomingIntraBssSdcchRadioLack, 5--360
hoFailureIncomingIntraBssSdcchTchnAckTimerExp, 5--362
hoFailureIncomingIntraBssTchChannelActivateNack, 5--359
hoFailureIncomingIntraBssTchHoNotAllowed, 5--359
hoFailureIncomingIntraBssTchIncompatible, 5--360
hoFailureIncomingIntraBssTchRadioLack, 5--359
hoFailureIncomingIntraBssTchTchnAckTimerExp, 5--360
hoFailureIntraBtsSdcchChannelActivateNack, 5--358
hoFailureIntraBtsSdcchRadioLack, 5--358
hoFailureIntraBtsSdcchTchnAckTimerExp, 5--358
hoFailureIntraBtsTchChannelActivateNack, 5--357
hoFailureIntraBtsTchRadioLack, 5--357
hoFailureIntraBtsTchTchnAckTimerExp, 5--357
hoFailureOutgoingInterBssSdcchHoNotAllowed, 5--373
hoFailureOutgoingInterBssSdcchOtherCases, 5--373
hoFailureOutgoingInterBssSdcchRadioLack, 5--372
hoFailureOutgoingInterBssSdcchT7TimerExp, 5--373
hoFailureOutgoingInterBssSdcchTerrestLack, 5--372
hoFailureOutgoingInterBssTchHoNotAllowed, 5--370
hoFailureOutgoingInterBssTchIncompatible, 5--371
hoFailureOutgoingInterBssTchOtherCases, 5--371
hoFailureOutgoingInterBssTchRadioLack, 5--370
hoFailureOutgoingInterBssTchT7TimerExp, 5--371
hoFailureOutgoingInterBssTchTerrestLack, 5--370
hoFailureOutgoingIntraBssSdcchChannelActivateNack, 5--369
hoFailureOutgoingIntraBssSdcchHoNotAllowed, 5--369
hoFailureOutgoingIntraBssSdcchRadioLack, 5--368
hoFailureOutgoingIntraBssSdcchTchnAckTimerExp, 5--369
hoFailureOutgoingIntraBssTchChannelActivateNack, 5--367
hoFailureOutgoingIntraBssTchHoNotAllowed, 5--366
hoFailureOutgoingIntraBssTchIncompatible, 5--368
hoFailureOutgoingIntraBssTchRadioLack, 5--366
hoFailureOutgoingIntraBssTchTchnAckTimerExp, 5--367
hoFailureTieringTchNorrLargeToSmallPattern, 5--397
hoFailureTieringTchNorrSmallToLargePattern, 5--397
hoIndicationNotTreatedTchoke, 5--230
hoInExecutionBscSdcch, 5--514
hoInExecutionBscTch, 5--514
hoInInterSdcchExecutionBscFailRate, 5--505
hoInInterSdcchSelectionBscFailRate, 5--504
hoInInterTchExecutionBscFailRate, 5--505
hoInInterTchSelectionBscFailRate, 5--504
hoInIntraSdcchExecutionBscFailRate, 5--506
hoInIntraTchExecutionBscFailRate, 5--506
hoInSdcchExecutionFailMaxRate, 5--496
hoInSdcchExecutionFailRate, 5--481
hoInSdcchSelectionFailMaxRate, 5--495
hoInSdcchSelectionFailRate, 5--480
hoInTchExecutionFailMaxRate, 5--496
hoInTchExecutionFailRate, 5--480
hoInTchSelectionFailMaxRate, 5--495
hoInTchSelectionFailRate, 5--479
hoIntraBtsFailRateTchTieringLargeToSmallPattern, 5--490
hoIntraBtsFailRateTchTieringSmallToLargePattern, 5--490
hoNcellsExecution, 5--257
hoNcellsExecutionSdcch, 5--258
hoNCellsExecutionTchAmrFr, 5--82
hoNCellsExecutionTchAmrHr, 5--82
hoNCellsRequestOutgoingAmrFr, 5--87
hoNCellsRequestOutgoingAmrHr, 5--87
hoNcellsRequestOutgoingDirectedRetry, 5--424
hoNcellsRequestOutgoingDistance, 5--423
hoNcellsRequestOutgoingDownlinkQuality, 5--423
hoNcellsRequestOutgoingDownlinkStrength, 5--422
hoNcellsRequestOutgoingInterCellOM, 5--425
hoNcellsRequestOutgoingOther, 5--426
hoNcellsRequestOutgoingPowerBudget, 5--424
hoNCellsRequestOutgoingTraffic, 5--425
hoNcellsRequestOutgoingUplinkQuality, 5--422
hoNcellsRequestOutgoingUplinkStrength, 5--421
hoNcellsSuccessOutgoingDirectedRetry, 5--430
hoNcellsSuccessOutgoingDistance, 5--428
hoNcellsSuccessOutgoingDownlinkQuality, 5--428
hoNcellsSuccessOutgoingDownlinkStrength, 5--427
hoNcellsSuccessOutgoingInterCellOM, 5--430
hoNcellsSuccessOutgoingOther, 5--431
hoNcellsSuccessOutgoingPowerBudget, 5--429
hoNcellsSuccessOutgoingTraffic, 5--431
hoNcellsSuccessOutgoingUplinkQuality, 5--427
hoNcellsSuccessOutgoingUplinkStrength, 5--426
hoNcellsUnsuccessSdcchChlR, 5--259
hoNcellsUnsuccessSdcchOther, 5--260
hoNcellsUnsuccessSdcchTimer, 5--260
hoNCellsUnsuccessTchAmrFrClearCommand, 5--85
hoNCellsUnsuccessTchAmrFrHandoverFailure, 5--84
hoNCellsUnsuccessTchAmrFrTimerExpiration, 5--84
hoNCellsUnsuccessTchAmrHrClearCommand, 5--83
hoNCellsUnsuccessTchAmrHrHandoverFailure, 5--83
hoNCellsUnsuccessTchAmrHrTimerExpiration, 5--83
hoNcellsUnsuccessTchChlR, 5--258
hoNcellsUnsuccessTchOther, 5--259
hoNcellsUnsuccessTchTimer, 5--259
hoOutExecutionBscSdcch, 5--513
hoOutExecutionBscTch, 5--513
hoOutFirstSuccessSdcchRatio, 5--509
hoOutFirstSuccessTchRatio, 5--508
hoOutInterSdcchExecutionBscFailRate, 5--507
hoOutInterTchExecutionBscFailRate, 5--507
hoOutSdcchBscGlobalFailRate, 5--498
hoOutSdcchBscGlobalFailRateV11, 5--498
hoOutSdcchExecutionBscFailRate, 5--503
hoOutSdcchExecutionFailMaxRate, 5--494
hoOutSdcchExecutionFailRate, 5--478
hoOutSdcchFirstAttemptSuccessMinRatio, 5--497
hoOutSdcchFirstAttemptSuccessRatio, 5--482
hoOutSdcchGlobalFailRate, 5--474
hoOutSdcchGlobalFailRateV11, 5--474
hoOutSdcchMaxFailRate, 5--491
hoOutSdcchMaxFailRateV11, 5--491
hoOutSdcchRequestBscRatio, 5--500
hoOutSdcchRequestBscRatioV11, 5--500
hoOutSdcchRequestMaxRatio, 5--492
hoOutSdcchRequestMaxRatioV11, 5--492
hoOutSdcchRequestRatio, 5--475
hoOutSdcchRequestRatioV11, 5--475
hoOutSdcchSelectionBscFailRate, 5--501
hoOutSdcchSelectionFailMaxRate, 5--493
hoOutSdcchSelectionFailRate, 5--477
hoOutTchBscGlobalFailRate, 5--498
hoOutTchBscGlobalFailRateV11, 5--498
hoOutTchExecutionBscFailRate, 5--502
hoOutTchExecutionFailMaxRate, 5--494
hoOutTchExecutionFailRate, 5--477
hoOutTchFirstAttemptSuccessMinRatio, 5--497
hoOutTchFirstAttemptSuccessRatio, 5--481
hoOutTchGlobalFailRate, 5--473
hoOutTchGlobalFailRateV11, 5--473
hoOutTchMaxFailRate, 5--491
hoOutTchMaxFailRateV11, 5--491
hoOutTchRequestBscRatio, 5--499
hoOutTchRequestBscRatioV11, 5--499
hoOutTchRequestMaxRatio, 5--492
hoOutTchRequestMaxRatioV11, 5--492
hoOutTchRequestRatio, 5--474
hoOutTchRequestRatioV11, 5--474
hoOutTchSelectionBscFailRate, 5--501
hoOutTchSelectionFailMaxRate, 5--493
hoOutTchSelectionFailRate, 5--476
hoRequestIncomingInterBss, raw permanent, 5--123
hoRequestIncomingInterBss8W, 5--447
hoRequestIncomingInterBssSdcch, raw permanent, 5--163
hoRequestIncomingIntraBss, raw permanent, 5--122
hoRequestIncomingIntraBss8W, 5--446
hoRequestIncomingIntraBssSdcch, raw permanent, 5--162
hoRequestIncomingIntraBssTchMsDualb, 5--391
hoRequestIntraBts, raw permanent, 5--129
hoRequestIntraBts8W, 5--448
hoRequestIntraBtsMsDualb, 5--394
hoRequestIntraBtsSdcch, raw permanent, 5--167
hoRequestOutgoingEbandEbandMsDualb, 5--384
hoRequestOutgoingEbandMbandMsDualb, 5--385
hoRequestOutgoingInterBss, raw permanent, 5--127
hoRequestOutgoingInterBss8W, 5--448
hoRequestOutgoingInterBssSdcch, raw permanent, 5--166
hoRequestOutgoingInterBssSdcch8W, 5--450
hoRequestOutgoingIntraBss, raw permanent, 5--126
hoRequestOutgoingIntraBss8W, 5--448
hoRequestOutgoingIntraBssSdcch, raw permanent, 5--165
hoRequestOutgoingIntraBssSdcch8W, 5--450
hoRequestOutgoingMbandEbandMsDualb, 5--262
hoRequestOutgoingMbandMbandMsDualb, 5--384
hoRequestOutgoingMultiband, 5--262
hoRequiredSdcch, 5--380
hoRequiredSdcchCapture, raw permanent, 5--157
hoRequiredSdcchDistance, raw permanent, 5--156
hoRequiredSdcchDownlinkQuality, raw permanent, 5--156
hoRequiredSdcchDownlinkStrength, raw permanent, 5--155
hoRequiredSdcchInterBtsOm, raw permanent, 5--159
hoRequiredSdcchIntraBtsDownlink, raw permanent, 5--159
hoRequiredSdcchIntraBtsOm, raw permanent, 5--158
hoRequiredSdcchIntraBtsUplink, raw permanent, 5--158
hoRequiredSdcchPowerBudget, raw permanent, 5--157
hoRequiredSdcchTraffic, 5--160
hoRequiredSdcchUplinkQuality, raw permanent, 5--155
hoRequiredSdcchUplinkStrength, raw permanent, 5--154
hoRequiredTch, 5--380
hoRequiredTchCapture, raw permanent, 5--146
hoRequiredTchDirectedRetry, raw permanent, 5--149
hoRequiredTchDistance, raw permanent, 5--145
hoRequiredTchDownlinkQuality, raw permanent, 5--144
hoRequiredTchDownlinkStrength, raw permanent, 5--143
hoRequiredTchInterBtsOm, raw permanent, 5--151
hoRequiredTchIntraBtsDownlink, raw permanent, 5--149
hoRequiredTchIntraBtsOm, raw permanent, 5--147
hoSuccessOutgoingTch, 5--382
hoSuccessTieringTchLargeToSmallPattern, 5--398
hoSuccessTieringTchSmallToLargePattern, 5--398
hoUnsuccessIncomingInterBssSdcchOtherCases, 5--379
hoUnsuccessIncomingInterBssSdcchTimerExp, 5--379
hoUnsuccessIncomingInterBssTchOtherCases, 5--379
hoUnsuccessIncomingInterBssTchTimerExp, 5--378
hoUnsuccessIncomingIntraCellSdcchReturnOldChannel, 5--378
hoUnsuccessIncomingIntraCellSdcchT3103TimerExp, 5--378
hoUnsuccessIncomingIntraCellTchReturnOldChannel, 5--377
hoUnsuccessIncomingIntraCellTchT3103TimerExp, 5--377
hoUnsuccessOutgoingInterBssNAttemptSdcch, 5--232
hoUnsuccessOutgoingInterBssNAttemptTch, 5--231
hoUnsuccessOutgoingInterCellSdcchOtherCases, 5--377
hoUnsuccessOutgoingInterCellSdcchReturnOldChannel, 5--376
hoUnsuccessOutgoingInterCellSdcchT3103TimerExp, 5--376
hoUnsuccessOutgoingInterCellTchOtherCases, 5--376
hoUnsuccessOutgoingInterCellTchReturnOldChannel, 5--375
hoUnsuccessOutgoingInterCellTchReturnOldChannel8W, 5--453
hoUnsuccessOutgoingInterCellTchT3103TimerExp8w, 5--454
hoUnsuccessOutgoingInterCellTchT3107TimerExp, 5--375
hoUnsuccessOutgoingInterCellTchT3107TimerExp8w, 5--375
hoUnsuccessOutgoingIntraBssNAttemptSdcch, 5--231
hoUnsuccessOutgoingIntraBssNAttemptTch, 5--230
hoUnsuccessOutgoingIntraCellSdcchReturnOldChannel, 5--374
hoUnsuccessOutgoingIntraCellSdcchT3103TimerExp, 5--375
hoUnsuccessOutgoingIntraCellTchReturnOldChannel, 5--374
hoUnsuccessOutgoingIntraCellTchReturnOldChannel8W, 5--453
hoUnsuccessOutgoingIntraCellTchT3103TimerExp, 5--374
hoUnsuccessOutgoingIntraCellTchT3107TimerExp8w, 5--453
hoUnsuccessReestIncomingIntraBssSdcch, 5--171
hoUnsuccessReestIncomingIntraBssTch, 5--142
hoUnsuccessReestIntraBtsSdcch, 5--169
hoUnsuccessReestIntraBtsTch, 5--140
hoUnsuccessReestOutgoingInterBssSdcch, 5--170
hoUnsuccessReestOutgoingInterBssTch, 5--141
hoUnsuccessReestOutgoingIntraBssSdcch, 5--170
hoUnsuccessReestOutgoingIntraBssTch, 5--141
I
immAssignDualBandMSRate, 5--489
immediateAssignmentMultiband, 5--261
immediateAssignmentReject, 5--355
immediateAssignmentRejectChanActNack, 5--172
immediateAssignmentRejectChanActTimmack, 5--173
immediateAssignmentRejectOthers, 5--174
immediateAssignmentRejectOverload, 5--173
immediateAssignmentRejectRadioRes, 5--172
immediateAssignmentRejectTimingAdv, 5--174
immediateAssignmentRejectTraffMsc, 5--171
immediateAssignmentSuccess, 5--354
immediateAssignmentSuccessCause000, 5--239
immediateAssignmentSuccessCause001, 5--240
immediateAssignmentSuccessCause010, 5--241
immediateAssignmentSuccessCause011, 5--241
immediateAssignmentSuccessCause100, 5--242
immediateAssignmentSuccessCause101, 5--243
immediateAssignmentSuccessCause110, 5--244
immediateAssignmentSuccessCause111, 5--245
incAmrFrDownModif, 5--100
incAmrFrDownModifTrZone, 5--100
incAmrFrUpModif, 5--99
incAmrFrUpModifTrZone, 5--99
incAmrHrDownModif, 5--101
incAmrHrDownModifTrZone, 5--101
incAmrHrUpModif, 5--100
incAmrHrUpModifTrZone, 5--100
intracellAmrFrDownHoRequiredTch, 5--74
intracellAmrFrUpHoRequiredTch, 5--73
invalidBlocksUp, 5--605
invalidProtocolErrorBlocksUp, 5--605
L
lapdOverloadRejectedOpSicd0, 5--27
listenerDetectionExpiry, 5--456
llcDiscardedOctets, 5--582
llcDiscardedPdu, 5--582
llcPacketsDn, 5--601
llcPacketsUp, 5--601
localBusy, 5--599
localMsgBlockCapacity, 5--629
localMsgBlockUsageAvg, 5--629
localMsgBlockUsageMax, 5--629
localMsgBlockUsageMin, 5--629
lossOfComNN002Max, 5--612
lossOfComNT0001, 5--614
lossOfComT3169, 5--613
lossOfComT3191, 5--616
lossOfComT3195, 5--615
M
MaxDlThroughput, 5--581
memoryCapacityFastRam, 5--625
memoryCapacityNormalRam, 5--626
memoryCapacitySharedRam, 5--626
memoryUsageAvgFastRam, 5--627
memoryUsageAvgMaxFastRam, 5--627
memoryUsageAvgMaxNormalRam, 5--627
memoryUsageAvgMaxSharedRam, 5--628
memoryUsageAvgMinFastRam, 5--627
memoryUsageAvgMinNormalRam, 5--627
memoryUsageAvgMinSharedRam, 5--628
memoryUsageAvgNormalRam, 5--627
memoryUsageAvgSharedRam, 5--628
msClassSensitivityToggle, 5--445
msFlowControlRequests, 5--582
msFlushLLRequest, 5--583
msLostMeasurements, 5--306
msLostMeasurementsAmrFr, 5--70
msLostMeasurementsAmrFrTrZone, 5--70
msLostMeasurementsAmrHr, 5--70
msLostMeasurementsAmrHrTrZone, 5--70
msLostMeasurementsTrZone, 5--306
msPowerDecControl, 5--400
msPowerDecControlAmrFr, 5--63
msPowerDecControlAmrHr, 5--68
msPowerIncControl, 5--399
msPowerIncControlAmrFr, 5--63
msPowerIncControlAmrHr, 5--67
N
nbSamplesDnQuality, 5--610
nbSamplesUpQuality, 5--609
noPacketResourceReq, 5--611
notifsReachMaxTransmit, 5--563
notifsReceived, 5--562
notifsSentOnce, 5--563
notifsTransmitAgainOnce, 5--563
notifsTransmitAgainTwiceAndMore, 5--563
O
octetDiscarded, 5--578
octetsDataDn, 5--577
octetsDataUp, 5--578
octetsDn, 5--576
octetsUp, 5--576
omcDatabaseUsed, 5--569
omcDatabaseUsedCum, 5--569
omcDatabaseUsedEch, 5--569
omcInputIFrame, 5--13
omcInputRepeatedIFrame, 5--14
omcInputRnrFrame, 5--15
omcLinkSwitchOver, 5--11
omcOutputIFrame, 5--13
omcOutputRepeatedIFrame, 5--14
omcOutputRnrFrame, 5--15
omcSybaseCpuBusy, 5--568
omcSybaseIdle, 5--568
omcSybaseIoBusy, 5--568
omcSybasePacketErr, 5--569
omcSybasePacketIn, 5--568
omcSybasePacketOut, 5--569
omcSybaseTotalError, 5--567
omcSybaseTotalRead, 5--567
omcSybaseTotalWrite, 5--567
omcUnixBasePartition, 5--574
omcUnixBasePartitionCum, 5--574
omcUnixBasePartitionEch, 5--574
omcUnixCpu0Used, 5--572
omcUnixCpu0UsedCum, 5--572
omcUnixCpu1Used, 5--572
omcUnixCpu1UsedCum, 5--572
omcUnixCpu1UsedEch, 5--572
omcUnixDataPartition, 5--575
omcUnixDataPartitionCum, 5--575
omcUnixDataPartitionEch, 5--575
omcUnixMailPartition, 5--574
omcUnixMailPartitionCum, 5--574
omcUnixMailPartitionEch, 5--574
omcUnixObsPartition, 5--574
omcUnixObsPartitionCum, 5--574
omcUnixRootPartition, 5--573
omcUnixRootPartitionCum, 5--573
omcUnixRootPartitionEch, 5--573
omcUnixSwap, 5--573
omcUnixSwapCum, 5--573
omcUnixSwapEch, 5--573
omcUnixTmpPartition, 5--573
omcUnixTmpPartitionCum, 5--573
omcUnixTmpPartitionEch, 5--573
omcX25AbortsPort0, 5--572
omcX25AbortsPort1, 5--572
omcX25AbortsPort2, 5--572
omcX25AbortsPort3, 5--572
omcX25CrcErrorsPort0, 5--571
omcX25CrcErrorsPort1, 5--571
omcX25CrcErrorsPort2, 5--571
omcX25CrcErrorsPort3, 5--571
omcX25PacketInPort0, 5--571
omcX25PacketInPort1, 5--571
omcX25PacketInPort2, 5--571
omcX25PacketInPort3, 5--571
omcX25PacketOutPort0, 5--571
omcX25PacketOutPort1, 5--571
omcX25PacketOutPort2, 5--571
omcX25PacketOutPort3, 5--571
ommdActConf, 5--557
ommdActRequest, 5--557
ommdCancelGetConf, 5--558
ommdCancelGetRequest, 5--558
ommdCreConf, 5--555
ommdCreRequest, 5--555
ommdDelConf, 5--557
ommdDelRequest, 5--556
ommdGetConf, 5--555
ommdGetRequest, 5--554
ommdSetConf, 5--556
ommdSetRequest, 5--556
omnetActConf, 5--561
omnetActRequest, 5--561
omnetCancelGetConf, 5--562
omnetCancelGetRequest, 5--562
omnetCreConf, 5--559
omnetCreRequest, 5--559
omnetDelConf, 5--561
omnetDelRequest, 5--560
omnetGetConf, 5--559
omnetGetRequest, 5--558
omnetSetConf, 5--560
omnetSetRequest, 5--560
outOfSequenceBlocksUp, 5--606
P
packetAckNackDn, 5--607
packetAckNackUp, 5--606
packetResourceRequest, 5--612
pagingFilteredByBsc, 5--35
pagingResponse, raw instrument panel, 5--349
pathBalanceMoy/Max/Cum/Ech, 5--38
pchAveragedQueueLength, 5--277
pchAveragedQueueLengthCell, 5--526
pchAveragedQueueLengthCellCum, 5--526
pchAveragedQueueLengthCellEch, 5--526
pchAveragedQueueLengthCellMax, 5--526
pchAveragedQueueLengthCellMoy, 5--526
pchAveragedQueueLengthEch, 5--277
pchAveragedQueueLengthMax, 5--277
pchAveragedQueueLengthTs2Ech, 5--277
pchAveragedQueueLengthTs2Moy, 5--277
pchAveragedQueueLengthTs4Cum, 5--277
pchAveragedQueueLengthTs4Ech, 5--277
pchAveragedQueueLengthTs4Moy, 5--277
pchAveragedQueueLengthTs6Cum, 5--277
pchAveragedQueueLengthTs6Ech, 5--277
pchAveragedQueueLengthTs6Moy, 5--277
pchMoreWait/Ts2/Ts4/Ts6, 5--110
pchMoreWaitCell, 5--526
pchNoWait/Ts2/Ts4/Ts6, 5--105
pchNoWaitCell, 5--525
pchOneWait/Ts2/Ts4/Ts6, 5--107
pchOneWaitCell, 5--525
pchQueuePagesDiscarded, 5--279
pchQueuePagesDiscardedCell, 5--527
pchQueuePagesDiscardedTs2, 5--279
pchQueuePagesDiscardedTs4, 5--279
pchQueuePagesDiscardedTs6, 5--279
pchTwoWait/Ts2/Ts4/Ts6, 5--109
pchTwoWaitCell, 5--525
pcmErrCorrEfficiency, 5--518
pcmFaultDDTIBoard, 5--20
pcmFaultExternal, 5--19
pcmFaultInternal, 5--20
pcmFaultOutOfService, 5--20
pcminsecondsMoy/Max/Cum/Ech, 5--520
pcmUnavailabilityMoy/Max/Cum/Ech, 5--10
pcuAgprsJokerNbofBlocksDn, 5--655
pcuAgprsJokerNbofBlocksUp, 5--660
pcuAgprsMainNbofBlocksDn, 5--649
pcuAgprsMainNbofBlocksUp, 5--659
pcuChannelRequestOnePhase, 5--691
pcuContentionFailureOnePhase, 5--692, 5--694
pcuDlThroughput, 5--579
pcuDlThroughputCum, 5--578
pcuDlThroughputNbs, 5--579
pcuDyAgprsLoadCriterionNbs, 5--637
pcuDyAgprsNbTimeslots, 5--634
pcuDyAgprsNbTimeslotsCun, 5--634
pcuDyAgprsNbTimeslotsNbs, 5--634
pcuDynAgprsJokerAvgNbTimeslot, 5--655
pcuDynAgprsJokerCumNbTimeslot, 5--654
pcuDynAgprsJokerMaxNbTimeslot, 5--655
pcuDynAgprsJokerMinNbTimeslot, 5--654
pcuEdgeCell15114s0, 5--652
pcuEdgeCell15115s0, 5--653
pcuEdgeCell15116s0, 5--653
pcuEdgeCell15117s0, 5--653
pcuEdgeCell15120s0, 5--656
pcuEdgeCell15121s0, 5--656
pcuEdgeCell15125s0, 5--658
pcuEdgeCell15126s0, 5--659
pcuEdgeDataBlocksReceivedUp, 5--643
pcuEdgeDnAvg8PskMeanBep, 5--644
pcuEdgeDnAvgUsefulDataPerCell, 5--652
pcuEdgeDnCum8PskMeanBep, 5--644
pcuEdgeDnAvgGmskMeanBep, 5--645
pcuEdgeDnCumGmskMeanBep, 5--645
pcuEdgeDnCumUsefulDataPerCell, 5--652
pcuEdgeDnNbs8PskMeanBep, 5--644
pcuEdgeDnNbsGmskMeanBep, 5--645
pcuEdgeDnNbsUsefulDataPerCell, 5--652
pcuEdgeDnTransmittedMcs2, 5--662
pcuEdgeDnTransmittedMcs3, 5--662
pcuEdgeDnTransmittedMcs5, 5--663
pcuEdgeDnTransmittedMcs6, 5--663
pcuEdgeDnTransmittedMcs7, 5--664
pcuEdgeDnTransmittedMcs8, 5--664
pcuEdgeDnTransmittedMcs9, 5--665
pcuEdgeDnUsefulDataDurationPerCell, 5--658
pcuEdgeDowngradedTbf, 5--649
pcuEdgeDowngradedTbfAvg, 5--649
pcuEdgeDowngradedTbfNbs, 5--649
pcuEdgeLADnTargetedTransmittedMcs2, 5--670
pcuEdgeLADnTargetedTransmittedMcs3, 5--671
pcuEdgeLADnTargetedTransmittedMcs5, 5--671
pcuEdgeLADnTargetedTransmittedMcs6, 5--672
pcuEdgeLADnTargetedTransmittedMcs7, 5--672
pcuEdgeLADnTargetedTransmittedMcs8, 5--673
pcuEdgeLADnTargetedTransmittedMcs9, 5--673
pcuEdgeLAUpTargetedTransmittedMcs2, 5--686
pcuEdgeLAUpTargetedTransmittedMcs3, 5--687
pcuEdgeLAUpTargetedTransmittedMcs5, 5--688
pcuEdgeLAUpTargetedTransmittedMcs6, 5--688
pcuEdgeLAUpTargetedTransmittedMcs7, 5--689
pcuEdgeLAUpTargetedTransmittedMcs8, 5--690
pcuEdgeLAUpTargetedTransmittedMcs9, 5--690
pcuEdgeMcs2RequestRetransDataBlockDn, 5--666
pcuEdgeMcs2RequestRetransDataBlockUp, 5--680
pcuEdgeMcs3RequestRetransDataBlockDn, 5--666
pcuEdgeMcs3RequestRetransDataBlockUp, 5--680
pcuEdgeMcs5RequestRetransDataBlockDn, 5--667
pcuEdgeMcs5RequestRetransDataBlockUp, 5--681
pcuEdgeMcs6RequestRetransDataBlockDn, 5--667
pcuEdgeMcs6RequestRetransDataBlockUp, 5--682
pcuEdgeMcs7RequestRetransDataBlockDn, 5--668
pcuEdgeMcs7RequestRetransDataBlockUp, 5--683
pcuEdgeMcs8RequestRetransDataBlockDn, 5--668
pcuEdgeMcs8RequestRetransDataBlockUp, 5--684
pcuEdgeMcs9RequestRetransDataBlockDn, 5--669
pcuEdgeMcs9RequestRetransDataBlockUp, 5--685
pcuEdgeTbfEstReq, 5--657
pcuEdgeTdma15100s0, 5--643
pcuEdgeTdma15105s0, 5--647
pcuEdgeTdma15106s0, 5--647
pcuEdgeTdma15107s0, 5--647
pcuEdgeTdma15108s0, 5--648
pcuEdgeTdma15109s0, 5--648
pcuEdgeUpAvgMeanBep, 5--646
pcuEdgeUpAvgUsefulDataPerCell, 5--650
pcuEdgeUpCumMeanBep, 5--646
pcuEdgeUpCumUsefulDataPerCell, 5--650
pcuEdgeUpNbsMeanBep, 5--646
pcuEdgeUpNbsUsefulDataPerCell, 5--650
pcuEdgeUpTransmittedMcs2, 5--674
pcuEdgeUpTransmittedMcs3, 5--675
pcuEdgeUpTransmittedMcs5, 5--676
pcuEdgeUpTransmittedMcs6, 5--677
pcuEdgeUpTransmittedMcs7, 5--678
pcuEdgeUpTransmittedMcs8, 5--678
pcuEdgeUpTransmittedMcs9, 5--679
pcuEdgeUpUsefulDataDurationPerCell, 5--657
pcuLackAbisJokerTSAvg, 5--660
pcuLackAbisJokerTSCum, 5--660
pcuLackAbisJokerTSNbs, 5--660
pcuUpPipeGreater22kbps, 5--694
pcuUpTbfImmediateAssignmentOnePhase, 5--692
pcuUpThroughputAvg, 5--693
pcuUpThroughputCum, 5--693
pcuUpThroughputNbs, 5--693
pduDataDn, 5--577
pduDataUp, 5--577
preemptedEdgeTsMoy/Max/Cum/Ech, 5--40
preemptedEdgeTsCellMoy/Max/Cum/Ech, 5--42
preemptedEdgeTsTrZoneMoy/Max/Cum/Ech, 5--40
prLoadCne3OmuSbcMoy/Max/Cum/Ech, 5--46
prLoadCne3TmuPmcMoy/Max/Cum/Ech, 5--47
prLoadCne3TmuSbcMoy/Max/Cum/Ech, 5--47
prLoadCpueMoy/Max/Cum/Ech, 5--17
prLoadCpue1Moy/Max/Cum/Ech, 5--17
prLoadCpue2Moy/Max/Cum/Ech, 5--17
prLoadCpumMoy/Max/Cum/Ech, 5--16
prLoadSicd[x], 5--18
psPaging, 5--632
PsPagingOnCCCH, 5--584
Q
qualityHoFiltered, 5--70
R
rachAccessCount/Ts2/Ts4/Ts6, 5--104
rachAccessCountCell, 5--524
rachBusyCount/Ts2/Ts4/Ts6, 5--103
rachBusyCountCell, 5--524
rachNonDecodedAvLevelMoy/Max/Cum/Ech, 5--112
rachNonDecodedAvLevelCell, 5--526
rachNonDecodedAvLevelCum, 5--112
rachNonDecodedAvLevelEch, 5--112
rachNonDecodedAvLevelMax, 5--112
rachNonDecodedAvLevelTs2, 5--112
rachNonDecodedAvLevelTs2Cum, 5--112
rachNonDecodedAvLevelTs2Ech, 5--112
rachNonDecodedAvLevelTs2Max, 5--112
rachNonDecodedAvLevelTs4, 5--112
rachNonDecodedAvLevelTs4Cum, 5--112
rachNonDecodedAvLevelTs4Ech, 5--112
rachNonDecodedAvLevelTs4Max, 5--112
rachNonDecodedAvLevelTs6, 5--112
rachNonDecodedAvLevelTs6Cum, 5--112
rachNonDecodedAvLevelTs6Ech, 5--112
radioFrameUlReceived, 5--344
rafficRelease8W, 5--451
relativeTimeDLPowerCtrlMaxSdcch, 5--488
relativeTimeDLPowerCtrlMaxTch, 5--487
relativeTimeULPowerCtrlMaxSdcch, 5--488
relativeTimeULPowerCtrlMaxTch, 5--487
requestedHandoverForDualBandMSToSecondVersusMainBand, 5--489
RequestedRetransmittedDataBlocksDN, 5--601
resumeFailureAfterHOInterBSC, 5--459, 5--460
retransmittedDataBlocksDn, 5--610
rsttraceDatabaseUsed, 5--570
rsttraceDatabaseUsedCum, 5--570
rsttraceDatabaseUsedEch, 5--570
rxBytes, 5--630
rxFrames, 5--630
rxLevDownLink, 5--308
RxLevDownlinkAmrFr, 5--61
RxLevDownlinkAmrFrTrZone, 5--61
RxLevDownlinkAmrHr, 5--66
RxLevDownlinkAmrHrTrZone, 5--66
rxLevDownLinkTrZone, 5--308
rxLevUpLink, 5--309
RxLevUplinkAmrFr, 5--61
RxLevUplinkAmrFrTrZone, 5--61
RxLevUplinkAmrHr, 5--66
RxLevUplinkAmrHrTrZone, 5--66
rxLevUpLinkTrZone, 5--310
rxQualDownLink, 5--311
RxQualDownlinkAmrFr, 5--62
RxQualDownlinkAmrFrTrZone, 5--62
RxQualDownlinkAmrHr, 5--67
RxQualDownlinkAmrHrTrZone, 5--67
rxQualDownLinkTrZone, 5--312
rxQualUpLink, 5--313
RxQualUplinkAmrFr, 5--62
RxQualUplinkAmrFrTrZone, 5--62
RxQualUplinkAmrHr, 5--67
RxQualUplinkAmrHrTrZone, 5--67
rxQualUpLinkTrZone, 5--314
rxTotalLinkUtil, 5--631
S
saicTchSuccessfullyAssigned, 5--46
saicTchSuccessfullyAssignedTrZone, 5--46
sapi3SessionEstablishment, 5--306
sccpAllocated, 5--132
sccpAllocatedLcs, 5--133
sccpAveragedUsed, raw permanent, 5--134
sccpResourceFailureRatio, 5--510
sccpRessourceFailure, 5--135
sccpRessourceFailureBscRefusal, 5--136
sccpRessourceFailureBscRefusalLcs, 5--137
sccpRessourceFailureLcs, 5--136
scseFailConnect, 5--548
scseRgeIn, 5--548
scseTgeOut, 5--548
scseTotAssocFree, 5--549
scseTotTgeRefused, 5--548
sdcchAllocated, 5--281
sdcchAllocatedTrZone, 5--281
sdcchAverageConfiguratedCum, 5--407
sdcchAverageConfiguratedEch, 5--407
sdcchAverageConfiguratedMax, 5--407
sdcchAverageConfiguratedMoy, 5--407
sdcchAverageConfiguratedTrZoneCum, 5--407
sdcchAverageConfiguratedTrZoneEch, 5--407
sdcchAverageConfiguratedTrZoneMax, 5--407
sdcchAverageConfiguratedTrZoneMoy, 5--407
sdcchAveragedAvailableCum, 5--320
sdcchAveragedAvailableEch, 5--320
sdcchAveragedAvailableMax, 5--320
sdcchAveragedAvailableMoy, 5--320
sdcchAveragedAvailableTrZone, 5--320
sdcchAveragedAvailableTrZoneCum, 5--320
sdcchAveragedAvailableTrZoneEch, 5--320
sdcchAveragedAvailableTrZoneMax, 5--320
sdcchAveragedUsedCum, 5--282
sdcchAveragedUsedEch, 5--282
sdcchAveragedUsedMax, 5--282
sdcchAveragedUsedMoy, 5--282
sdcchAveragedUsedTrZoneCum, 5--282
sdcchAveragedUsedTrZoneEch, 5--282
sdcchAveragedUsedTrZoneMax, 5--282
sdcchAveragedUsedTrZoneMoy, 5--282
sdcchRessourceFailure, 5--284
sdcchRessourceFailureTrZone, 5--284
sharedMsgBlockCapacity, 5--628
sharedMsgBlockUsageAvg, 5--628
sharedMsgBlockUsageAvgMax, 5--628
sharedMsgBlockUsageAvgMin, 5--628
signallingAbnormalReleaseCell, 5--381
signallingPhaseDurationHighMoy/Max/Cum/Ech, 5--115
signallingPhaseDurationMoy/Max/Cum/Ech, 5--113
signallingReleaseBts, 5--355
signallingReleaseBts8W, 5--450
signallingReleaseBtsCallClearing, 5--185
signallingReleaseBtsCicRemovalEqptFail, 5--184
signallingReleaseBtsClearCommand, 5--192
signallingReleaseBtsCnxFailRadioIntFail, 5--185
signallingReleaseBtsCnxFailRadioLinkFail, 5--186
signallingReleaseBtsCnxFailRemTransFail, 5--196
signallingReleaseBtsErrorIndDm, 5--191
signallingReleaseBtsErrorIndSeq, 5--191
signallingReleaseBtsErrorIndT200, 5--189
signallingReleaseBtsIncFirstL3, 5--180
signallingReleaseBtsOmCicRemoval, 5--183
signallingReleaseBtsOmRadioChanBloc, 5--184
signallingReleaseBtsOmTsRemoval, 5--182
signallingReleaseBtsOthers, 5--195
signallingReleaseBtsReleaseInd, 5--187
signallingReleaseBtsReset, 5--179
signallingReleaseBtsResetCirc, 5--179
signallingReleaseBtsRfResInd, 5--193
signallingReleaseBtsSccpDataRefusal, 5--180
signallingReleaseBtsSccpDiscInd, 5--178
signallingReleaseBtsSwitchOver, 5--193
signallingReleaseBtsT11, 5--196
signallingReleaseBtsT3101, 5--181
signallingReleaseBtsT3103, 5--194
signallingReleaseBtsT3107CircDown, 5--182
signallingReleaseBtsT3107CircDown8W, 5--451
signallingReleaseBtsT8, 5--195
signallingReleaseBtsTmodMs, 5--194
signallingReleaseBtsTsRemovalEqptFail, 5--183
signallingReleaseCellTbcEdge, 5--197
signallingReleaseNoBts, 5--355
signallingReleaseNoBtsBadDataInd, 5--177
signallingReleaseNoBtsOthers, 5--178
signallingReleaseNoBtsReset, 5--175
signallingReleaseNoBtsSccpDataRefusal, 5--176
signallingReleaseNoBtsSccpDiscInd, 5--175
signallingReleaseNoBtsTsccRel, 5--177
signallingReleaseRatio, 5--523
speechAlgoFallBack, 5--260
ss7InputMsu, 5--461
ss7Level2ErrorMsuCongest, 5--462
ss7Level2ErrorNegAckRec, 5--462
ss7Level2ErrorNegAckTrans, 5--462
ss7Level2ErrorSuErr, 5--463
ss7Level3ErrorDelay, 5--463
ss7Level3ErrorHighErrRate, 5--463
ss7OutputMsu, 5--461
successfulTchFrSeizures, 5--117
successfulTchFrSeizures8W, 5--445
successfulTchFrSeizuresMsDualb, 5--341
sybaseCpuBusy, 5--545
sybaseIdle, 5--545
sybaseIoBusy, 5--545
sybasePacketErr, 5--546
sybasePacketIn, 5--545
sybasePacketOut, 5--546
sybaseTotalError, 5--544
sybaseTotalRead, 5--544
sybaseTotalWrite, 5--544
T
t3103ExpSdcch, 5--485
t3103ExpTch, 5--484
t3107ExpAssign, 5--483
t3107ExpIntraBtsHoSdcch, 5--483
t3107ExpIntraBtsHoTch, 5--484
tbfNormalReleaseDn, 5--611
tbfNormalReleaseUp, 5--610
tcAllocated, 5--130
tcAveragedUsed, raw permanent, 5--131
tchAveragedQueueLengthHighPriorityCum, 5--296
tchAveragedQueueLengthHighPriorityEch, 5--296
tchAveragedQueueLengthHighPriorityMax, 5--296
tchAveragedQueueLengthHighPriorityMoy, 5--296
tchAveragedQueueLengthOtherPriority, 5--297
tchFrAllocated, 5--349
tchFrAllocatedOverflowAllocation, 5--287
tchFrAllocatedOverflowAllocationTrZone, 5--287
tchFrAllocatedPrimoAllocation, 5--286
tchFrAllocatedPrimoAllocationTrZone, 5--286
tchFrAllocatedTchAllocation, 5--285
tchFrAllocatedTchAllocationTrZone, 5--285
tchFrAllocatedTrZone, 5--350
tchFrAllocatedWps, 5--288
tchFrAllocatedWpsTrZone, 5--288
tchFrAverageConfigurated, 5--406
tchFrAverageConfiguratedCellMoy/Max/Cum/Ech, 5--419
tchFrAverageConfiguratedCum, 5--406
tchFrAverageConfiguratedEch, 5--406
tchFrAverageConfiguratedMax, 5--406
tchFrAverageConfiguratedMoy, 5--406
tchFrAverageConfiguratedTrZoneCum, 5--406
tchFrAverageConfiguratedTrZoneEch, 5--406
tchFrAverageConfiguratedTrZoneMax, 5--406
tchFrAverageConfiguratedTrZoneMoy, 5--406
tchFrAveragedAvailable, 5--318
tchFrAveragedAvailableCellMoy/Max/Cum/Ech, 5--418
tchFrAveragedAvailableCum, 5--318
tchFrAveragedAvailableEch, 5--318
tchFrAveragedAvailableMax, 5--318
tchFrAveragedAvailableMoy, 5--318
tchFrAveragedAvailableTrZoneCum, 5--318
tchFrAveragedAvailableTrZoneEch, 5--318
tchFrAveragedAvailableTrZoneMax, 5--318
tchFrAveragedAvailableTrZoneMoy, 5--318
tchFrAveragedUsedAllocationMax, 5--291
tchFrAveragedUsedCellMoy/Max/Cum/Ech, 5--419
tchFrAveragedUsedCum, 5--352
tchFrAveragedUsedEch, 5--352
tchFrAveragedUsedMax, 5--352
tchFrAveragedUsedMoy, 5--352
tchFrAveragedUsedNsc, 5--352
tchFrAveragedUsedOverflowAllocationCellMoy/Max/Cum/Ech, 5--417
tchFrAveragedUsedOverflowAllocationCum, 5--292
tchFrAveragedUsedOverflowAllocationEch, 5--292
tchFrAveragedUsedOverflowAllocationMax, 5--292
tchFrAveragedUsedOverflowAllocationMoy, 5--292
tchFrAveragedUsedOverflowAllocationTrZoneCum, 5--292
tchFrAveragedUsedOverflowAllocationTrZoneEch, 5--292
tchFrAveragedUsedOverflowAllocationTrZoneMax, 5--292
tchFrAveragedUsedOverflowAllocationTrZoneMoy, 5--292
tchFrAveragedUsedPrimoAllocation, 5--511
tchFrAveragedUsedPrimoAllocationCellMoy/Max/Cum/Ech, 5--416
tchFrAveragedUsedPrimoAllocationMoy, 5--291
tchFrAveragedUsedPrimoAllocationTrZoneCum, 5--291
tchFrAveragedUsedPrimoAllocationTrZoneEch, 5--291
tchFrAveragedUsedPrimoAllocationTrZoneMax, 5--291
tchFrAveragedUsedPrimoAllocationTrZoneMoy, 5--291
tchFrAveragedUsedTchAllocationCellMoy/Max/Cum/Ech, 5--415
tchFrAveragedUsedTchAllocationMoy/Max/Cum/Ech, 5--289
tchFrAveragedUsedTchAllocationTrZoneMoy/Max/Cum/Ech, 5--289
tchFrAveragedUsedTrZoneCum, 5--352
tchFrAveragedUsedTrZoneEch, 5--352
tchFrAveragedUsedTrZoneMax, 5--352
tchFrAveragedUsedTrZoneMoy, 5--352
tchFrAveragedUsedWpsCellMoy/Max/Cum/Ech, 5--417
tchFrAveragedUsedWpsMoy/Max/Cum/Ech, 5--293
tchFrAveragedUsedWpsTrZoneMoy/Max/Cum/Ech, 5--293
tchFrRessourceFailure, 5--295
tchFrRessourceFailureTrZone, 5--295
tchHrAllocated, 5--351
tchHrAllocatedNsc, 5--351
tchHrAllocatedTchAllocation, 5--288
tchHrAllocatedTchAllocationTrZone, 5--288
tchHrAllocatedTrZone, 5--351
tchHrAllocatedWps, 5--36
tchHrAllocatedWpsTrZone, 5--36
tchHrAveragedUsedCellMoy/Max/Cum/Ech, 5--420
tchHrAveragedUsedMoy/Max/Cum/Ech, 5--353
tchHrAveragedUsedNscCellMoy/Max/Cum/Ech, 5--421
tchHrAveragedUsedTchAllocationMoy/Max/Cum/Ech, 5--294
tchHrAveragedUsedTchAllocationTrZoneMoy/Max/Cum/Ech, 5--294
tchHrAveragedUsedTrZoneMoy/Max/Cum/Ech, 5--353
tchHrAveragedUsedWpsCellMoy/Max/Cum/Ech, 5--420
tchHrAveragedUsedWpsTrZoneMoy/Max/Cum/Ech, 5--36
tchHrRessourceFailure, 5--296
tchHrRessourceFailureTrZone, 5--296
tchOccupancy, 5--533
tchQueuingDurationHighPriority, 5--299
tchQueuingDurationOtherPriority, 5--300
tchQueuingExpirationHighPriority, 5--298
tchQueuingExpirationOtherPriority, 5--298
tdmaClassTchResourceFailureRatio, 5--527
timingAdvanceAmrFrAvg, 5--64
timingAdvanceAmrFrMax, 5--65
timingAdvanceAmrHrAvg, 5--69
timingAdvanceAmrHrMax, 5--69
timingAdvanceAverage, 5--404
timingAdvanceAverageTrZone, 5--404
timingAdvanceMaximum, 5--405
timingAdvanceMaximumTrZone, 5--405
totalNumberOfEdgeTsMoy/Max/Cum/Ech, 5--39
totalNumberOfEdgeTsCellMoy/Max/Cum/Ech, 5--41
totalNumberOfEdgeTsTrZoneMoy/Max/Cum/Ech, 5--39
totalNumberOfPacketTsMoy/Max/Cum/Ech, 5--410
totalNumberOfPacketTsCellMoy/Max/Cum/Ech, 5--414
totalNumberOfPacketTsUsedForCircuitMoy/Max/Cum/Ech, 5--411
totalNumberOfPacketTsUsedForCircuitCellMoy/Max/Cum/Ech, 5--414
totalNumberOfPacketTsUsedForCircuitTrZoneMoy/Max/Cum/Ech, 5--411
totalRetransmissionRequested, 5--607
traceDatabaseSeg0Used, 5--569
traceDatabaseSeg0UsedCum, 5--569
traceDatabaseSeg0UsedEch, 5--569
traceDatabaseSeg1Used, 5--570
traceDatabaseSeg1UsedCum, 5--570
traceDatabaseSeg1UsedEch, 5--570
trafficAbnormalRelease, 5--381
trafficAbnormalRelease8w, 5--454
trafficRelease, 5--356
trafficReleaseAmrFrLapdmCause, 5--85
trafficReleaseAmrFrOthersCause, 5--86
trafficReleaseAmrFrRadioCause, 5--85
trafficReleaseAmrHrLapdmCause, 5--86
trafficReleaseAmrHrOthersCause, 5--86
trafficReleaseAmrHrRadioCause, 5--86
trafficReleaseCallClearing, 5--202
trafficReleaseCicRemovalEqptFail, 5--201
trafficReleaseClearCommand, 5--208
trafficReleaseCnxFailRadioIntFail, 5--203
trafficReleaseCnxFailRadioLinkFail, 5--203
trafficReleaseCnxFailRemTransFail, 5--221
trafficReleaseErrorIndDm, 5--207
trafficReleaseErrorIndSeq, 5--208
trafficReleaseErrorIndT200, 5--206
trafficReleaseOmCicRemoval, 5--201
trafficReleaseOmRadioChanBloc, 5--202
trafficReleaseOmTsRemoval, 5--200
trafficReleaseOthers, 5--211
trafficReleaseReleaseInd, 5--204
trafficReleaseReset, 5--198
trafficReleaseResetCirc, 5--198
trafficReleaseRfResInd, 5--209
trafficReleaseSccpDataRefusal, 5--199
trafficReleaseSccpDiscInd, 5--197
trafficReleaseSysInfoFail, 5--221
trafficReleaseT3103, 5--210
trafficReleaseT3107CircDown, 5--199
trafficReleaseT8, 5--211
trafficReleaseTbcEdge, 5--32
trafficReleaseTmodMs, 5--210
trafficReleaseTsRemovalEqptFail, 5--200
txBytes, 5--630
txFrames, 5--631
U
ulsecondPhaseAllocFailure, 5--596
ulsecondPhaseRadioFailure, 5--599
unixCmnBasePartitionNMCSrv, 5--554
unixCmnBasePartitionNMCSrvCum, 5--554
unixCmnBasePartitionNMCSrvEch, 5--554
unixCmnDataPartitionNMCSrv, 5--554
unixCmnDataPartitionNMCSrvCum, 5--554
unixCmnDataPartitionNMCSrvEch, 5--554
unixCpu0UsedNMCSrv, 5--549
unixCpu0UsedNMCSrvCum, 5--549
unixCpu0UsedNMCSrvEch, 5--549
unixCpu1UsedNMCSrv, 5--549
unixCpu1UsedNMCSrvCum, 5--549
unixCpu1UsedNMCSrvEch, 5--549
unixDataSsnPartition, 5--552
unixDataSsnPartitionCum, 5--552
unixDataSsnPartitionEch, 5--552
unixMdrBasePartitionNMCSrv, 5--553
unixMdrBasePartitionNMCSrvCum, 5--553
unixMdrBasePartitionNMCSrvEch, 5--553
unixMdrDataPartitionNMCSrv, 5--553
unixMdrDataPartitionNMCSrvCum, 5--553
unixMdrDataPartitionNMCSrvEch, 5--553
unixNotifPartition, 5--551
unixNotifPartitionCum, 5--551
unixNotifPartitionEch, 5--551
unixObsPartition, 5--551
unixObsPartitionCum, 5--551
unixObsPartitionEch, 5--551
unixRestoredNotifPartition, 5--552
unixRestoredNotifPartitionCum, 5--552
unixRestoredNotifPartitionEch, 5--552
unixRestoredObsPartition, 5--551
unixRestoredObsPartitionCum, 5--551
unixRestoredObsPartitionEch, 5--551
unixRestoredTracePartition, 5--553
unixRestoredTracePartitionCum, 5--553
unixRestoredTracePartitionEch, 5--553
unixRootPartitionNMCSrv, 5--550
unixRootPartitionNMCSrvCum, 5--550
unixRootPartitionNMCSrvEch, 5--550
unixSwapNMCSrv, 5--550
unixSwapNMCSrvCum, 5--550
unixSwapNMCSrvEch, 5--550
unixTmpPartitionNMCSrv, 5--550
unixTmpPartitionNMCSrvCum, 5--550
unixTmpPartitionNMCSrvEch, 5--550
unixTracePartition, 5--552
unixTracePartitionCum, 5--552
unixTracePartitionEch, 5--552
uplinkPowerCtrlMaxSdcchCum, 5--273
uplinkPowerCtrlMaxSdcchEch, 5--273
uplinkPowerCtrlMaxSdcchMax, 5--273
uplinkPowerCtrlMaxSdcchMoy, 5--273
uplinkPowerCtrlMaxTchAmrFrMoy/Max/Cum/Ech, 5--60
uplinkPowerCtrlMaxTchAmrHrMoy/Max/Cum/Ech, 5--65
uplinkPowerCtrlMaxTchCum, 5--256
uplinkPowerCtrlMaxTchEch, 5--256
uplinkPowerCtrlMaxTchMax, 5--256
uplinkPowerCtrlMaxTchMoy, 5--256
upMultiSlotRequest1, 5--584
upMultiSlotRequest3, 5--586
upMultiSlotRequest4, 5--587
upPipeGreater11kbps, 5--621
upPipeless11kbps, 5--620
upTbfBronzeRejectedForMinTput, 5--623
upTbfBronzeSatisfactBet5090pCent, 5--622
upTbfBronzeSatisfactLess50pCent, 5--623
upTbfBronzeSatisfactMore90pCent, 5--621
upTbfGoldRejectedForMinTput, 5--589
upTbfGoldSatisfactBet5090pCent, 5--588
upTbfGoldSatisfactLess50pCent, 5--589
upTbfGoldSatisfactMore90pCent, 5--588
upTbfImmAssigRejectNoPdch, 5--617
upTbfImmediateAssignment, 5--617
upTbfReleases, 5--597
upTbfSilverRejectedForMinTput, 5--620
upTbfSilverSatisfactLess50pCent, 5--622
upUserdatablocks, 5--600
V
vgcsAccessGrant, 5--267
vgcsMscReject, 5--267
W
wpsAccessBarringDurationClass0to9, 5--440, 5--441, 5--442, 5--443
wpsAccessBarringDurationClass11, 5--441
wpsAccessBarringDurationClass12, 5--441
wpsAccessBarringDurationClass13, 5--442
wpsAccessBarringDurationClass14, 5--442
wpsAccessBarringDurationClass15, 5--443
WPUBWPSQ, 5--443
WQABAND, 5--443
WQOVFL1, 5--437
WQOVFL2, 5--437
WQOVFL3, 5--437
WQOVFL4, 5--438
WQOVFL5, 5--438
WQTOUT1, 5--438, 5--439, 5--440
WQTOUT2, 5--439
WQTOUT3, 5--439
WQTOUT4, 5--439
WQTOUT5, 5--440
WQUEDHO, 5--444, 5--455
WQUEUED1, 5--435, 5--436
WQUEUED2, 5--435
WQUEUED3, 5--436
WQUEUED4, 5--436
WQUEUED5, 5--436
NORTEL CONFIDENTIAL:
The information contained in this document is the property of Nortel For more information, please contact:
Networks. Except as specifically authorized in writing by Nortel
Networks, the holder of this document shall keep the information For all countries, except USA:
contained herein confidential and shall protect same in whole or in part
NORTEL
from disclosure and dissemination to third parties and use for evaluation,
operation and maintenance purposes only. Documentation Department
Parc d’activité de Magny--Chateaufort
You may not reproduce, represent, or download through any means, the CHATEAUFORT
information contained herein in any way or in any form without prior 78928 YVELINES CEDEX 9
written consent of Nortel Networks. FRANCE
The following are trademarks of Nortel Networks: *NORTEL , the Email : umts--gsm.ntp@nortel.com
NORTEL corporate logo, the NORTEL Globemark, UNIFIED Fax : (33) (1) 39--44--50--29
NETWORKS, S2000, S4000, S8000.
GSM is a trademark of France Telecom. In the USA:
All other brand and product names are trademarks or registered
NORTEL
trademarks of their respective holders.
Global Knowledge Services
Publication Reference
PE/DCL/DD/0125 411--9001--125 2221 Lakeside Boulevard
15.154/EN Richardson TX 75082
May 2006 USA
Originated in France Tel: 1--800--4 NORTEL
1--(800)--466--7838 or (972) 684--5935
Internet Address:
http://www.nortel.com