Vous êtes sur la page 1sur 42

13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Final Exam
Due Dec 7 at 1:59am Points 60 Questions 60
Available Dec 6 at 2am - Dec 15 at 1:59am 9 days Time Limit 120 Minutes

A empt History
Attempt Time Score
LATEST Attempt 1 109 minutes 52.5 out of 60

Score for this quiz: 52.5 out of 60


Submitted Dec 10 at 7:04pm
This attempt took 109 minutes.

Question 1 1 / 1 pts

Which approach is being used when network maintenance is performed in


order of urgency?

baseline

structured

Correct! interrupt-driven

regular maintenance cycle

Refer to Chapter 3.

Question 2 1 / 1 pts

Which structured maintenance methodology should a network engineer use?


https://1363293.netacad.com/courses/560444/quizzes/4846193 1/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

the methodology that is outlined by Cisco

the methodology that is approved by the ISO

the methodology that is suggested by the ITU-T

Correct! the methodology that is prescribed by the organization

Refer to Chapter 2.

Question 3 1 / 1 pts

What is a characteristic of network maintenance?

Network maintenance typically excludes consideration of network changes.

Correct!
Maintaining network documentation is an important element of network
maintenance.

The amount of resources expended on network maintenance is consistent


across all companies.

Proper network maintenance will eliminate network downtime.

Refer to Chapter 3.

Question 4 1 / 1 pts
https://1363293.netacad.com/courses/560444/quizzes/4846193 2/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Which backup mechanism presents the highest security risk?

HTTPS

FTP

SCP

Correct!
TFTP

Refer to Chapter 3.

Question 5 1 / 1 pts

What are two limitations of using buffered logging? (Choose two.)

Correct!
Log messages are removed when a device is powered down.

Only high severity messages can be captured.

Messages are lost when there is a connectivity issue.

Correct!
Oldest messages are overwritten when allocated memory is exceeded.

Message services may have messages filtered through a firewall.

Refer to Chapter 3.

Question 6 1 / 1 pts

https://1363293.netacad.com/courses/560444/quizzes/4846193 3/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

What is the highest logging severity level message that is displayed by


default on the console line?

informational (6)

warning (4)

error (3)

Correct!
debugging (7)

notification (5)

Refer to Chapter 3.

Question 7 1 / 1 pts

What best describes a stratum 3 time source?

The clock is synchronized to a stratum 1 time server.

The clock is synchronized to a stratum 0 time server.

The clock acts as a time source for other stratum 3 time servers.

The clock acts as a time source for stratum 2 time servers.

Correct!
The clock is synchronized to a time server that is in turn synchronized to a
stratum 1 time server.

https://1363293.netacad.com/courses/560444/quizzes/4846193 4/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to Chapter 3.

Question 8 1 / 1 pts

Which two advantages does scheduled maintenance offer over interrupt-


driven events? (Choose two.)

Correct!
reduced network downtime

simplified troubleshooting processes

Correct!
predictable lead times for change requests

maintenance windows during regular business hours

faster time to resolution of problems

Refer to Chapter 3.

Question 9 1 / 1 pts

Refer to the exhibit. Based on the output that is generated, which two
statements are true? (Choose two.)

https://1363293.netacad.com/courses/560444/quizzes/4846193 5/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

The $h and $t parameters will automatically add the device hostname and
version number to the archive filename.

The time-period parameter must be configured to enable the automatic


archiving of the running-configuration file everytime it is saved to NVRAM.

Correct!
Every time the running configuration file is saved to NVRAM, it will also be
automatically archived.

Use the archive config privileged EXEC mode command to replace the
running configuration file with the most recent archived file.

Correct!
The archive path is the only mandatory archive parameter that must be
configured.

Refer to Chapter 3.

Question 10 0 / 1 pts

Refer to the exhibit. Which two FTP-related statements are true? (Choose
two.)

https://1363293.netacad.com/courses/560444/quizzes/4846193 6/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

You Answered
The Configuration Rollback feature was preconfigured on router R1 via the
archive command.

orrect Answer
The ip ftp username and ip ftp password commands were issued on router
R1.

The login credentials were sent to the FTP server in an encrypted format.

The R1-test.cfg configuration was successfully copied from the FTP server to
the startup configuration file of router R1.

The R1-test.cfg configuration was successfully copied from the FTP server to
the running configuration file of router R1.

Correct!

The configuration was copied using a method that is less secure than HTTPS.

Refer to Chapter 3.

Question 11 0 / 1 pts

What term refers to alleviating the symptoms of the problem without resolving
the root cause?

You Answered escalation

hypothesis

orrect Answer workaround

https://1363293.netacad.com/courses/560444/quizzes/4846193 7/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

solution

Refer to Chapter 2.

Question 12 1 / 1 pts

What is the final task in a structured troubleshooting process?

testing the hypothesis

Correct!
documenting the changes

gathering information

eliminating possible causes

Refer to Chapter 2.

Question 13 0 / 1 pts

RSPAN depends on which type of VLAN?

orrect Answer RSPAN VLAN

management VLAN

native VLAN

You Answered default VLAN

https://1363293.netacad.com/courses/560444/quizzes/4846193 8/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

private VLAN

black hole VLAN

Refer to Chapter 5.

Question 14 1 / 1 pts

Which command would a network administrator use to verify which VLANs


are allowed on a trunk?

show vlan interface

Correct! show interfaces trunk

show vlan

show mac address-table

Refer to Chapter 2.

Question 15 1 / 1 pts

Refer to the exhibit. A port channel link between a branch site and the main
site experiences an outage after a hardware upgrade at the branch site. The

https://1363293.netacad.com/courses/560444/quizzes/4846193 9/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

network administrator at the main site checks the log and sees a
%SPANTREE-2-CHNL_MISCFG message. What is a likely cause of this
message?

The main site has inconsistencies in the physical ports that are members of
the channel.

Correct!
The main site has been configured to bundle links into an EtherChannel and
the branch site has not.

The branch site is running a newer, incompatible version of the Spanning Tree
Protocol.

The branch site has been configured for the Spanning Tree Protocol, but the
main site has not.

Refer to Chapter 3.

Question 16 1 / 1 pts

What happens to the route connected to a routed port on a multilayer switch


when the port goes down?

It is tagged to be removed and the backup route is installed as the primary.

It remains in the routing table as unavailable.

Correct! It is immediately removed from the routing table.

https://1363293.netacad.com/courses/560444/quizzes/4846193 10/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

It is removed from the routing table at the next spanning-tree convergence.

Refer to Chapter 4.

Question 17 1 / 1 pts

Refer to the exhibit. Switch1 and Switch2 are unable to establish a trunk link.
Based on the information in the exhibit, what could be the reason for this
problem?

Correct! native VLAN mismatch

VTP mismatch

https://1363293.netacad.com/courses/560444/quizzes/4846193 11/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

MTU mismatch

switchport mode mismatch

encapsulation mismatch

DTP mismatch

Refer to Chapter 3.

Question 18 1 / 1 pts

Refer to the exhibit. In a converged spanning tree, how many blocked ports
will there be in VLAN 1 for the pictured topology?

https://1363293.netacad.com/courses/560444/quizzes/4846193 12/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Correct! 2

Refer to Chapter 6.

Question 19 0 / 1 pts

A network administrator is troubleshooting why hosts are taking a suboptimal


path to another network and suspects that it is an EIGRP routing problem.
Which command should be used to verify which neighbors sent routes, the
state of those neighbors, and the distance vector metrics associated with
those routes?

You Answered show ip eigrp neighbors

show ip eigrp interfaces

debug ip routing

debug eigrp packets

orrect Answer show ip eigrp topology

Refer to Chapter 7.

Question 20 1 / 1 pts

A network administrator is troubleshooting packet flow in a routed network


where there are two or more equal routes for a particular prefix. Why would

https://1363293.netacad.com/courses/560444/quizzes/4846193 13/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

the show ip cef exact-route source destination command be useful in this


scenario?

The output displays all redundant paths in the FIB.

The output displays all prefixes in the routing table that fall within the prefix
specified.

Correct! The output displays which of the paths a particular packet would take.

The output displays the contents of the routing table instead of the FIB.

Refer to Chapter 6.

Question 21 1 / 1 pts

A network administrator uses the clear ip arp * command on a router. What


type of issue is he likely troubleshooting?

Correct! IP address to Ethernet MAC address mappings

redundant paths on multipoint interfaces

routing table entries

the contents of the FIB

Refer to Chapter 6.

https://1363293.netacad.com/courses/560444/quizzes/4846193 14/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Question 22 1 / 1 pts

What are two problems that can occur when routes are redistributed in two
directions? (Choose two.)

Correct! routing loops

route filtering

Correct! suboptimal routing

lost external routes

lost seed metrics

Refer to Chapter 6.

Question 23 0 / 1 pts

Which two conditions could cause two routers to have trouble establishing a
neighbor relationship in an OSPF network? (Choose two.)

One of the routers is redistributing the OSPF routes into EIGRP.

You Answered Slow network connections cause OSPF advertisements to time out.

The network command has put the connected interfaces into the same OSPF
area.

Correct! Hello packets are not sent from either neighbor.

orrect Answer The interfaces have different network types.

https://1363293.netacad.com/courses/560444/quizzes/4846193 15/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to Chapter 7.

Question 24 0 / 1 pts

Which statement is true based on the show ip ospf neighbor command


output that is shown in the exhibit?

RTB has established an adjacency with RTA.

You Answered

RTB did not see its router ID in the hello packet that was received from RTA.

orrect Answer RTB did not receive a hello packet from RTA.

RTB is able to exchange routing updates with RTA.

Refer to Chapter 7.

Question 25 1 / 1 pts
https://1363293.netacad.com/courses/560444/quizzes/4846193 16/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

What are the three main data structures used by EIGRP? (Choose three.)

Correct!
interface table

routing table

Forwarding Information Base (FIB)

Routing Information Base (RIB)

Correct!
topology table

Correct!
neighbor table

Refer to Chapter 7.

Question 26 0 / 1 pts

What type of BGP message precedes the successful formation of a BGP


peering session?

orrect Answer open

keepalive

established

You Answered update

withdraw

https://1363293.netacad.com/courses/560444/quizzes/4846193 17/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to Chapter 7.

Question 27 1 / 1 pts

Which two pieces of information are displayed by the debug ip bgp


command? (Choose two.)

Correct!
BGP related events

route redistribution information

BGP updates

internal metrics of IBGP routes

Correct!
phases of BGP peering relationships

Refer to Chapter 7.

Question 28 1 / 1 pts

https://1363293.netacad.com/courses/560444/quizzes/4846193 18/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to the exhibit. A network administrator is unable to have two BGP


peers exchange routing information. Which solution would correct this
problem?

Change the neighbor x.x.x.x update-source command on R1 and R2 to refer


to the FastEthernet interfaces.

Remove the loopback interfaces on each router.

Enter the neighbor x.x.x.x ebgp-multihop 1 command on R1 and R2.

Correct!
Change the neighbor peer IP addresses on R1 and R2 to the loopback
interface IP address of the other router.

Refer to Chapter 7.

Question 29 1 / 1 pts

https://1363293.netacad.com/courses/560444/quizzes/4846193 19/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to the exhibit. A network administrator is unable to have two BGP


peers exchange routing information. Based on the output generated, which
solution would correct this problem?

Issue the neighbor x.x.x.x ebgp-multihop 1 command on both routers.

Issue the neighbor x.x.x.x update-source null command on both routers.

Issue the neighbor x.x.x.x update-source fastethernet0/0 command on both


routers.

Correct!
Issue the neighbor x.x.x.x update-source loopback0 command on both
routers.

Refer to Chapter 7.

Question 30 1 / 1 pts
https://1363293.netacad.com/courses/560444/quizzes/4846193 20/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to the exhibit and its partial output. During the testing of the network, it
was discovered that the workstations could ping the router but could not
reach any outside destinations. Troubleshooting revealed that proper
translations were being set up in the router, but communication still was not
occurring. What is the problem?

The access list should be placed on fa0/1 instead of on fa0/0.

The NAT address mapping statement is incorrect.

Correct!
The inbound access list is incorrect and should allow the 192.168.10.1
address.

The ip nat inside and ip nat outside commands are on the wrong interfaces.

https://1363293.netacad.com/courses/560444/quizzes/4846193 21/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to Chapter 6.

Question 31 1 / 1 pts

Refer to the exhibit. Based on the output of the debug ip nat command in
the exhibit, which two statements are true? (Choose two.)

The IP address 172.31.233.209 is the configured IP address on the remote


PC.

Correct!
Packets that are destined for 172.31.2.132 from source 192.168.1.95 are
translated into 172.31.233.209.

Packets were not translated for the return path from source 192.168.1.95.

Correct!
Entries that are indicated with NAT* have been translated via the fast path.

Entries with NAT* have the ToS value 5.

Refer to Chapter 6.

https://1363293.netacad.com/courses/560444/quizzes/4846193 22/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Question 32 1 / 1 pts

What is the correct sequence for the DHCP negotiation process?

Correct!
DHCPDISCOVER, DHCPOFFER, DHCPREQUEST, DHCPACK

DHCPREQUEST, DHCPOFFER, DHCPDISCOVER, DHCPACK

DHCPACK, DHCPOFFER, DHCPREQUEST, DHCPDISCOVER

DHCPDISCOVER, DHCPACK, DHCPREQUEST, DHCPOFFER

Refer to Chapter 6.

Question 33 1 / 1 pts

https://1363293.netacad.com/courses/560444/quizzes/4846193 23/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to the exhibit. A network administrator is troubleshooting a NAT


translation issue on router R2. The IP addresses of hosts on the R2 LAN are
not being translated by R2. Based on the information in the exhibit, what is
the issue?

The NAT pool is exhausted.

Correct!
The R2 LAN is not configured as an inside interface.

The ACL is using a wrong pool reference.

The static translation prevents any new dynamic translations.

Refer to Chapter 6.

Question 34 1 / 1 pts

Refer to the exhibit. A network administrator is troubleshooting a connectivity


issue between LAN clients on routers R1 and R3. Connectivity tests from R2
to the R1 and R3 LAN segments are successful. The administrator confirms
that a routing issue exists. Based on the information that is presented in the
exhibit, which configuration command would correct the problem?

Correct!
R1(config)# ip route 172.16.6.0 255.255.255.0 172.16.7.10

R1(config)# ip route 0.0.0.0 0.0.0.0 172.16.7.1

R2(config)# ip route 0.0.0.0 0.0.0.0 172.16.7.9

R2(config)# ip route 172.16.6.0 255.255.255.0 172.16.7.9

R3(config)# ip route 0.0.0.0 0.0.0.0 172.16.7.9

https://1363293.netacad.com/courses/560444/quizzes/4846193 24/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

R3(config)# ip route 172.16.6.0 255.255.255.0 172.16.7.10

Refer to Chapter 6.

Question 35 1 / 1 pts

Which Cisco IOS router configuration mode is used to enter the command ip
dhcp excluded-address 10.1.1.1?

user EXEC

interface configuration

Correct! global configuration

DHCP pool configuration

privileged EXEC

Refer to Chapter 6.

Question 36 1 / 1 pts

Refer to the exhibit. A network engineer is investigating a reported issue of


Computer1 not receiving its IP configuration from the DHCP server.
Computer2 is receiving its configuration from the DHCP server. What is a
plausible reason for this issue?

https://1363293.netacad.com/courses/560444/quizzes/4846193 25/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

The S0/0/0 interface of router East should be configured to provide DHCP


relay.

The WAN segment between routers East and North should be replaced with a
LAN.

Correct!

The DHCP server does not have a DHCP pool for 192.168.0.0 /24 network.

An ACL is blocking broadcasts into the F0/0 interface of router North .

Refer to Chapter 6.

Question 37 1 / 1 pts

Refer to the exhibit. Users are complaining that they are receiving duplicate
address error messages when they start their machines. What should the
administrator do to correct this problem?

Correct!
Use the ip dhcp excluded-address command to exclude any statically
assigned addresses from the DHCP pool.

Change the netmask to 255.0.0.0 to agree with the class A network that is
used in the DHCP pool.

Change the address assigned to the default router and dns server.

https://1363293.netacad.com/courses/560444/quizzes/4846193 26/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Decrease the DHCP lease time to make more addresses available at one
time.

Refer to Chapter 6.

Question 38 1 / 1 pts

Refer to the exhibit. Users are complaining that they are unable to connect to
resources outside of their corporate network during peak hours. What action
should the administrator take to correct this problem?

Remove the ACL because it is blocking connections.

Disable static NAT because it is interfering with the dynamic translations.

Change the FastEthernet 0/1 interface to an inside NAT interface.

Disable CEF because it is sending packets to the CPU for processing.

Correct!
Increase the size of the NAT pool to provide more IP addresses for translation.

Refer to Chapter 6.

Question 39 1 / 1 pts

https://1363293.netacad.com/courses/560444/quizzes/4846193 27/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to the exhibit. To verify network performance a network administrator


issued the show platform tcam utilization command on one of the
distribution switches. On the basis of the output provided, what conclusion
can be made?

TCAM will punt any unicast frames for directly connected routes to the CPU
for forwarding.

Subject to the QoS policy to the CPU for forwarding, TCAM will punt any
frames.

Subject to the security policy to the CPU for forwarding, TCAM will punt any
frames.

Correct!
TCAM will punt any additional unicast frames for remote networks to the CPU
for forwarding.

Refer to Chapter 4.

Question 40 1 / 1 pts

Refer to the exhibit. What is occurring with the ARP process on the South1-
1.10 switch?

https://1363293.netacad.com/courses/560444/quizzes/4846193 28/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

ARP has caused TCAM to punt packets to be process-switched.

ARP is using excessive CPU time.

ARP requests are indicating malicious network traffic.

Correct!
ARP is operating normally.

Refer to Chapter 4.

Question 41 1 / 1 pts

What are two reasons why a switch port would have a status of errdisable?
(Choose two.)

incorrect VLAN

misconfigured MLS

Correct!
late collisions

trunk mismatch

Correct!
duplex mismatch

Refer to Chapter 6.

Question 42 1 / 1 pts

https://1363293.netacad.com/courses/560444/quizzes/4846193 29/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to the exhibit. You have been asked to correct the configuration on R1
so that the Tunnel 0 interface does not flap and R3 can be consistently
reached from R1. What command would you issue on R1 to accomplish this?

ip route 172.16.25.3 255.255.255.255 Tunnel0

ip route 172.16.25.0 255.255.255.0 Serial0/0/0

ip route 10.3.3.3 255.255.255.255 Tunnel0

ip route 172.16.15.2 255.255.255.255 Tunnel0

Correct! ip route 10.3.3.3 255.255.255.255 Serial0/0/0

ip route 172.16.25.3 255.255.255.0 Serial0/0/0

Refer to Chapter 9.

Question 43 1 / 1 pts

Refer to the exhibit. You have been asked to troubleshoot a connectivity


issue between R3 and R1. From the partial output of the show running-
config command on both routers, what configuration change is required?

A static route should be added to R3 to point to the 192.168.1.0/24 network.

The tunnel destination for Tunnel0 on R1 should be the IP address of


Serial0/0/1 on R3.

https://1363293.netacad.com/courses/560444/quizzes/4846193 30/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

The tunnel source for Tunnel0 on R3 should be the IP address of Serial0/0/1


on R1.

A static route should be added to R1 to point to the 192.168.1.0/24 network.

Correct!
The tunnel destination for Tunnel0 on R3 should be the IP address of
Loopback0 on R1.

The tunnel source for Tunnel0 on R1 should be the IP address of Loopback0


on R3.

Refer to Chapter 9.

Question 44 1 / 1 pts

Which feature serves to offset the lack of authentication available with IEEE
802.1D Spanning Tree Protocol?

loop guard

root guard

DHCP snooping

Dynamic ARP Inspection

Correct!
BPDU guard

https://1363293.netacad.com/courses/560444/quizzes/4846193 31/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to Chapter 10.

Question 45 1 / 1 pts

Refer to the exhibit. What could be concluded about the TACACS+ failure
based on the exhibited command output from debug tacacs and debug aaa
authentication?

The TACACS+ server IP address has been incorrectly configured on the


router.

Correct!
The TACACS+ server key of the router does not match that of the TACACS+
server.

The TACACS+ server is not operational.

The username and password that were supplied by the user were rejected by
the TACACS+ server.

Refer to Chapter 9.

Question 46 1 / 1 pts

https://1363293.netacad.com/courses/560444/quizzes/4846193 32/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to the exhibit. A network administrator is trying to secure the remote


administration of the router by enabling the use of the SSH protocol. Which
changes should be made on the partial configuration as shown in the
graphic?

Correct!
The transport input telnet command should be changed to transport input
ssh.

The enable password must be encrypted.

The commands listed under the VTY line should be listed under the Console
line.

The transport input telnet command should be changed to transport input


none.

Refer to Chapter 8.

Question 47 1 / 1 pts

Which IPv6 protocol provides Layer 2 address mapping, Duplicate Address


Detection (DAD), and stateless autoconfiguration?

Address Resolution Protocol (ARP)

classless interdomain routing (CIDR)

Correct!
Neighbor Discovery (ND)

link-state advertisement (LSA)

https://1363293.netacad.com/courses/560444/quizzes/4846193 33/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to Chapter 6.

Question 48 1 / 1 pts

Refer to the exhibit. BPDU guard and PortFast have been configured on all
edge ports on the access switches. A junior network administrator tested a
new switch in the lab and verified that the bridge ID is 32887. What would
happen when the administrator plugs this switch into port Fa0/20 on ASW_1
in an attempt to extend the LAN?

Port Fa0/20 will become a root port.

Port Fa0/20 will start forwarding traffic immediately.

Correct!
Port Fa0/20 will be shut down.

Port Fa0/20 will transition from blocking to forwarding state after the spanning
tree convergence.

Refer to Chapter 6.

Question 49 1 / 1 pts

During a network security audit, the auditors indicated a security issue with
the transactions between the network devices and the authentication server.
The audit concluded that the content of the transactions is not being
encrypted. How can this security issue be corrected?
https://1363293.netacad.com/courses/560444/quizzes/4846193 34/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Change the authentication method to use UDP.

Change the authentication protocol to CHAP.

Correct! Change the authentication process and server to use TACACS.

Change the authentication server location to the network DMZ.

Refer to Chapter 8.

Question 50 1 / 1 pts

An administrator has just implemented two-way route redistribution between


an OSPF and EIGRP domain. However, network performance between
domains quickly degraded and an investigation revealed routing loops. What
action could be used to solve this issue?

Redistribute all subnets in both EIGRP and OSPF domains.

Change the seed metric of the routes being redistributed.

Configure an additional router to be a secondary point of route redistribution.

Correct! Filter the routes being redistributed between the protocols.

Refer to Chapter 9.

Question 51 1 / 1 pts

https://1363293.netacad.com/courses/560444/quizzes/4846193 35/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

How can you prevent the forming of an EIGRP adjacency on a specific


segment while still including the interfaces address in the EIGRP routing
updates?

By issuing the passive-interface default command.

Correct!
By issuing the passive-interface ethernet slot/number command.

By issuing the no auto-summary command.

By issuing the proper no network network [mask] command.

Refer to Chapter 6.

Question 52 1 / 1 pts

What can go wrong with BGP session on Layer 4?

Correct!
Access lists or firewalls are dropping relevant TCP packets.

Clock is not synchronized between BGP routers.

BGP authentication is failing.

BGP neighbors do not agree on session parameters.

Refer to Chapter 8.

Question 53 1 / 1 pts

https://1363293.netacad.com/courses/560444/quizzes/4846193 36/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Where is the outbound distribute list applied in the configuration?

On the outbound interface.

Correct! Under BGP configuration with the neighbor command.

In the global configuration.

None of the above.

Refer to Chapter 8.

Question 54 1 / 1 pts

Which NTP server is used for clock synchronization in the output below?

Router# show ntp associations

address ref clock st when poll reach delay offset disp

~192.165.100.101 .INIT. 16 - 1024 0 0.000 0.000 15937.

*~192.165.100.102 .LOCL. 1 615 1024 377 0.000 0.000 2.036

+~192.165.100.103 .LOCL. 1 509 1024 377 0.000 0.000 2.016

127.127.0.1

Correct! 192.165.100.102

192.165.100.101

192.165.100.103

https://1363293.netacad.com/courses/560444/quizzes/4846193 37/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to Chapter 8.

Question 55 1 / 1 pts

A DNS query was sent by the 10.0.3.33 host to a DNS server at 8.8.8.8.
Which access list line will be matched when the response arrives?

access-list 100 permit udp host 8.8.8.8 eq 53 10.0.3.33 0.0.0.255 eq 53

access-list 100 permit udp any 10.0.3.33 0.0.0.31 eq 53


access-list 100 permit udp any eq 53 10.0.3.3 0.0.0.31

access-list 100 permit udp any 10.0.3.32 0.0.0.31

Correct!
Line 4.

Line 1.

Line 2.

Line 3.

Refer to Chapter 8.

Question 56 0.5 / 1 pts

What does this output of the traceroute command mean? (Choose two.)

RouterPC> traceroute 209.165.201.45

https://1363293.netacad.com/courses/560444/quizzes/4846193 38/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Type escape sequence to abort.

Tracing the route to 209.165.201.45

VRF info: (vrf in name/id, vrf out name/id)

1 192.168.0.253 0 msec 0 msec 1 msec

2 192.168.0.253 !H !H *

* - Network unreachable.

Correct!
!H Host is unreachable.

Router with an IP address of 192.168.0.253 has responded to the ICMP


request.

!H Host interrupted test.

orrect Answer
* - The probe timed out.

Refer to Chapter 9.

Question 57 1 / 1 pts

Which show ip sla command displays number of succeed and failed tests?

show ip sla configuration

Correct!
show ip sla statistics

show ip sla application

https://1363293.netacad.com/courses/560444/quizzes/4846193 39/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

show ip sla results

Refer to Chapter 9.

Question 58 1 / 1 pts

A router is configured with a link-local address using ipv6 address fe80::123


link-local command. When you ping another link-local address, the router
prompts you to provide the source interface. Why?

This is the default behavior for ping when IPv6 addresses are used. It
determines which IPv6 address to use as the source address.

It uses interface information to permit the traffic returning from link-local


address in the access list, in case one is configured on the interface.

Correct!
The router does not know which interface leads to the link-local address you
want to ping, therefore the source interface must be manually set.

The configured link-local address belongs to the device and not particular
interface. This is the only way for the router to determine which interface and
link-local address to ping from.

Refer to Chapter 9.

https://1363293.netacad.com/courses/560444/quizzes/4846193 40/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Question 59 1 / 1 pts

Which protocol and port are used by TACACS+?

UDP/1812

Correct!
TCP/49

UDP/1645

TCP/47

Refer to Chapter 9.

Question 60 1 / 1 pts

Which best describes GRE protocol?

GRE uses original IP header and adds GRE header at the end of the packet.

GRE uses original IP header and inserts GRE header between IP header and
payload.

Correct!
GRE adds new IP header, inserts GRE header and encapsulates original IP
packet.

GRE adds new IP header, encapsulates original IP packet and adds GRE
header at the end of the IP packet.

https://1363293.netacad.com/courses/560444/quizzes/4846193 41/42
13/12/2017 Final Exam: 2017-3-TLM04-12_G1_TLM_BQ-PMV

Refer to Chapter 9.

Quiz Score: 52.5 out of 60

https://1363293.netacad.com/courses/560444/quizzes/4846193 42/42

Vous aimerez peut-être aussi