Académique Documents
Professionnel Documents
Culture Documents
Content
1. Outdoor units lineup ..........................................................2
2. Nomenclature ....................................................................3
3.Features ..............................................................................4
4. Description of main components ....................................8
5. Specifications..................................................................10
6. Dimensions......................................................................14
7. Piping Diagram................................................................15
8. Wiring Diagram ...............................................................16
9. Electric Characteristics ..................................................19
10. Capacity Tables .............................................................20
11. Operation Limits ............................................................26
12. Water Pressure Drop ....................................................28
13. Sound Level...................................................................31
14. Exploded View ..............................................................32
15. Installation ....................................................................38
16. Checking and Starting Up the Unit .............................51
17. Running and Maintenance ..........................................53
18. Controller .......................................................................56
19.Troubleshooting .............................................................69
20. Optional Accessories ...................................................94
※ Manufacture reserves the right to discontinue, or change at any time, specifications or designs without notices
and without incurring obligations.
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
MGC-V5W/D2N1, MGC-V7W/D2N1
MGC-V10W/D2N1, MGC-V12W/D2RN1
MGC-V14W/D2RN1, MGC-V16W/D2RN1
2
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
2. Nomenclature
M G C - V 5 W / D2 R N1
Refrigerant Type
N1:R410A Omit for R22
Power Supply
R:380~415V, 3Ph ,50Hz
Omit for 220~240V,1Ph,50Hz
Compressor Type
D: Digital scroll compressor
F: Fixed scroll compressor
V: Inverter compressor
3
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
3.Features
3.1 High efficient DC inverter compressor
Full DC inverter mini chiller adopts highly intelligent inverter-driven compressor. This advanced technology
enables the output of the outdoor unit to be modulated by the real heat load demands..
This advanced system ensures precise temperature regulation and highly efficient energy usage, making a
significant contribution to limiting the impact on the environment.
exchange performance.
Hydrophilic film fins and inner-threaded copper pipes optimize heat High efficiency inner-thread pipe,
enhance heat transfer.
exchange efficiency.
Optimally design fan shape and new designed discharge air grille and air deflector, making higher air volume
and reduces running noise..
Air deflector
New grille
New fan
4
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
EER
3.39 3.31
3.5 3.23 3.21 3.20
3.11
2.5
1.5
0.5
0
5kW 7kW 10kW 12kW 14kW 16kW
COP
3.5
3.5 3.31 3.30
3.24 3.25
3.2
2.5
1.5
0.5
0
5kW 7kW 10kW 12kW 14kW 16kW
3.5 Wide operation temperature range
Stable and safe running at wide ambient temperature range, cooling performance from -5 ˚C to 46˚C,
heating from -15˚C to 27˚C.
COOLING MODE
-5°C 46°C
HEATING MODE
-15°C 27°C
By adopting high efficiency plate heat exchanger, the energy consumption can be reduced.
5
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
Switch SW4_1(10kW) or SW3_1(12-16kW) on the PCB to ON to enable the following remote control
functions. The setting is not default at factory.
Remote shut down
Remote cooling and heating
Note: When all controller controls together, the unit will work according to the last order.
5/7kW will be available soon.
Note: When connecting wired controller, outdoor unit control panel is mainly used for display which can
check parameters and inquiry, and can’t be used to set mode and temperature.
Built-in water pressure gauge. Inspect the water pressure all the time.
Fully integrated and built-in hydraulic module, such as expansion tank, plate type of heat exchanger,
water circulating pump, etc. It saves installation space and cost.
Patented liquid distribution components to maximize performance and minimize defrost impact.
Stable and accurate gas flow control. EXV achieves 500 pulses to adjust flow precisely. Ensure the
temperature-control precisely and steadily to provide a comfortable environment.
6
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
100%
95%
90%
85%
80%
75%
70%
65%
60%
55%
50%
45%
40%
35%
30%
25%
20%
15%
10%
Press “Check” button for 3 seconds to start the water pump operating when the unit is standby. Press
“Check” button for 3 seconds again to stop the water pump.
7
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
2
3
13
4
5
6
7
8
10
5/7KW
1 Electrical panel
2 Display panel
3 Plate heat exchanger
4 4-way valve
5 High pressure switch
6 Low pressure switch
7 Water Pump
8 Accumulator
9 Water flow switch
10 Compressor
11 Condenser
12 Expansion tank
13 Axial-flow fan
8
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
1
2
11
3
4
12
5 13
6 14
15
7 16
17
18
8 19
9
10
10~16KW
9
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
5. Specifications
Model MGC-V5W/D2N1 MGC-V7W/D2N1
Power supply V-Ph-Hz 220-240, 1, 50 220-240, 1, 50
Capacity kW 5.0 7.0
Cooling*(1)
Input kW 1.55 2.25
Capacity kW 6.57 7.88
Cooling*(2)
Input kW 1.27 1.84
Capacity kW 5.5 8.0
Heating*(3)
Input kW 1.7 2.5
Capacity kW 6.32 8.29
Heating*(4)
Input kW 1.52 2.13
EER*(1) kW/kW 3.23 3.11
EER*(2) kW/kW 5.16 4.28
Max. input consumption kW 2.8 3.0
Max. input current A 14.6 15.6
Model SNB172FJGMC SNB172FJGMC
Type ROTARY ROTARY
Brand Mitsubishi Electric Mitsubishi Electric
Capacity kW 5.46 5.46
Compressor Input kW 1.64 1.64
Rated load current A 8.1 8.1
Locked rotor Amp A 29.5 29.5
Thermal protector Inner Inner
Refrigerant oil ml FV50S,400 FV50S,400
Model WZDK170-38G-1 WZDK170-38G-1
Type DC Motor DC Motor
Outdoor fan Brand
motor NIDEC SHIBAURA NIDEC SHIBAURA
Input W 170 170
Speed r/min 820 820
Number of rows 2 2
Tube pitch(a)× row pitch(b) mm 22×19.05 22×19.05
Fin spacing mm 1.6 1.6
Fin type Hydrophilic aluminum foil Hydrophilic aluminum foil
Outdoor coil
Tube outside dia. and type mm φ7.94 φ7.94
Inner grooved copper tube Inner grooved copper tube
Coil length ×height mm 885×880 885×880
Number of circuits 6 6
Type RS15/6-3-WILO RS15/6-3-WILO
Water pump Input (H/M/L) W 93/67/46 93/67/46
Pumping head m 5.5 5.5
Outdoor air flow m3/h 5100 5100
Throttle EXV+capillary EXV+capillary
Outdoor noise level (sound pressure)*(3) dB(A) 58 58
Water flow m3/h 0.86 1.20
The plate heat-exchanger water pressure kPa 15 15
drop
The Max. and Min. water inlet pressure kPa 500/150 500/150
Net dimension (W×H×D) mm 990×966×354 990×966×354
Outdoor Packing dimension mm 1120×1100×435 1120×1100×435
unit (W×H×D)
Net/ Gross weight kg 81/91 81/91
Type R410A R410A
Refrigerant
Charged volume kg 2.5 2.5
Connection Power wire mm2 3×2.5 3×2.5
wiring Signal wire mm2 3×0.75 3×0.75
Pipe Water inlet/outlet inch 1’’ 1’’
diameter
Control Wired controller Wired controller
Ambient temperature ℃ Cooling: -5℃~46℃; Heating: -15-27℃(Antifreeze must be added below 5℃)
Water outlet temperature range ℃ Cooling: 4~20 ℃; Heating: 30~55 ℃
2. Heating: (*3) warm water inlet/outlet temperature: 40/45°C,outdoor ambient temperature 7°C DB/6°C WB .
(*4) warm water inlet/outlet temperature: 30/35°C,outdoor ambient temperature 7°C DB/6°C WB .
3. It is tested 1m away in front of the unit in a semi-anechoic room(sound pressure).
4. The above data may be changed without notice for future improvement on quality and performance.
1. Cooling: (*1) chilled water inlet/outlet temperature: 12/7°C,outdoor ambient temperature 35°C DB.
(*2) chilled water inlet/outlet temperature: 23/18°C,outdoor ambient temperature 35°C DB.
2. Heating: (*3) warm water inlet/outlet temperature: 40/45°C,outdoor ambient temperature 7°C DB/6°C WB .
(*4) warm water inlet/outlet temperature: 30/35°C,outdoor ambient temperature 7°C DB/6°C WB .
3. It is tested 1m away in front of the unit in a semi-anechoic room(sound pressure).
4. The above data may be changed without notice for future improvement on quality and performance.
12
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
13
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
6. Dimensions
MGC-V5W/D2N1,MGC-V7W/D2N1 (Unit: mm)
354
966
990
366
624
MGC-V10W/D2N1,MGC-V12W/D2RN1,MGC-V14W/D2RN1,MGC-V16W/D2RN1
(Unit : mm)
1327
900
970
600
360
400
348
320
14
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
7. Piping Diagram
MGC-V5W/D2N1,MGC-V7W/D2N1
HEAT PUMP
16 18
6
2 7 5 7
10 HP
13
LP 11 4
14
12
Cooling
1 3 Heating
15
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
8. Wiring Diagram
MGC-V5W/D2N1,MGC-V7W/D2N1
16
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
MGC-V10W/D2N1
17
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
MGC-V12W/D2RN1,MGC-V14W/D2RN1,
MGC-V16W/D2RN1
18
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
9. Electric Characteristics
19
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
EER
EER
EER
EER
EER
EER
temp.
W/
(℃) kW kW W/W kW kW kW kW W/W kW kW W/W kW kW W/W kW kW W/W
W
5.00 5.60 1.37 4.10 5.27 1.41 3.75 4.97 1.45 3.43 4.70 1.50 3.14 4.40 1.57 2.80 4.05 1.65 2.46
6.00 5.79 1.39 4.17 5.44 1.43 3.81 5.13 1.47 3.48 4.85 1.52 3.19 4.54 1.59 2.85 4.19 1.67 2.50
7.00 5.99 1.41 4.23 5.63 1.46 3.86 5.30 1.50 3.53 5.00 1.55 3.23 4.70 1.63 2.88 4.33 1.71 2.53
8.00 6.17 1.46 4.24 5.80 1.50 3.86 5.45 1.55 3.52 5.14 1.60 3.22 4.83 1.68 2.88 4.46 1.76 2.53
9.00 6.35 1.47 4.31 5.95 1.52 3.93 5.60 1.56 3.58 5.27 1.61 3.27 4.96 1.69 2.93 4.58 1.78 2.58
10.00 6.59 1.49 4.41 6.17 1.54 4.01 5.80 1.59 3.65 5.45 1.64 3.33 5.14 1.72 2.99 4.75 1.80 2.63
11.00 6.77 1.51 4.49 6.34 1.55 4.08 5.95 1.60 3.71 5.59 1.65 3.38 5.27 1.73 3.04 4.88 1.82 2.68
12.00 6.93 1.53 4.53 6.48 1.58 4.11 6.07 1.63 3.73 5.70 1.68 3.40 5.38 1.76 3.06 4.99 1.85 2.70
13.00 7.05 1.54 4.57 6.59 1.59 4.14 6.17 1.64 3.76 5.79 1.69 3.43 5.47 1.77 3.08 5.08 1.86 2.72
14.00 7.23 1.55 4.65 6.75 1.60 4.21 6.31 1.65 3.82 5.92 1.70 3.48 5.60 1.79 3.13 5.20 1.88 2.77
15.00 7.32 1.56 4.69 6.83 1.61 4.24 6.38 1.66 3.85 5.97 1.71 3.49 5.66 1.80 3.15 5.26 1.89 2.79
16.00 7.50 1.58 4.76 6.99 1.63 4.30 6.53 1.68 3.90 6.11 1.73 3.54 5.79 1.81 3.19 5.39 1.90 2.83
17.00 7.60 1.58 4.80 7.07 1.63 4.33 6.60 1.68 3.92 6.17 1.74 3.55 5.85 1.82 3.21 5.45 1.91 2.85
Heating
Ambient temp.(℃)
-10 -6 -2 2 7 10 13
Hot
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
Power
COP
COP
COP
COP
COP
COP
COP
temp.
41.00 3.30 1.09 3.04 4.13 1.23 3.35 4.87 1.37 3.55 5.42 1.49 3.64 5.89 1.57 3.76 6.59 1.66 3.97 7.57 1.80 4.21
42.00 3.21 1.11 2.90 4.02 1.26 3.19 4.74 1.40 3.39 5.28 1.52 3.47 5.75 1.60 3.59 6.42 1.70 3.78 7.36 1.83 4.02
43.00 3.13 1.13 2.77 3.93 1.28 3.06 4.64 1.43 3.25 5.17 1.55 3.33 5.64 1.63 3.45 6.28 1.73 3.63 7.19 1.87 3.84
44.00 3.07 1.15 2.66 3.86 1.31 2.94 4.56 1.46 3.13 5.09 1.58 3.21 5.56 1.67 3.33 6.18 1.77 3.50 7.05 1.91 3.70
45.00 3.03 1.18 2.57 3.81 1.34 2.85 4.50 1.49 3.03 5.03 1.62 3.12 5.50 1.70 3.24 6.11 1.80 3.39 6.96 1.95 3.58
46.00 2.97 1.19 2.50 3.74 1.35 2.77 4.43 1.50 2.95 4.95 1.63 3.04 5.42 1.72 3.16 6.00 1.82 3.30 6.83 1.97 3.48
47.00 2.88 1.21 2.37 3.63 1.38 2.64 4.31 1.53 2.81 4.82 1.66 2.90 5.28 1.75 3.02 5.84 1.86 3.15 6.64 2.00 3.31
48.00 2.77 1.25 2.21 3.49 1.42 2.46 4.15 1.58 2.63 4.65 1.71 2.71 5.10 1.80 2.83 5.63 1.91 2.94 6.38 2.07 3.09
49.00 2.61 1.30 2.01 3.31 1.48 2.24 3.93 1.64 2.40 4.41 1.78 2.48 4.84 1.88 2.58 5.34 1.99 2.68 6.04 2.15 2.81
50.00 2.45 1.36 1.79 3.10 1.55 2.00 3.69 1.72 2.14 4.14 1.87 2.21 4.55 1.97 2.31 5.01 2.09 2.40 5.66 2.26 2.51
20
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
MGC-V7W/D2N1
Cooling
Ambient temp.(℃)
21.00 25.00 30.00 35.00 40.00 46.00
Chilled
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
EER
EER
EER
EER
EER
EER
temp.
W/
(℃) kW kW W/W kW kW kW kW W/W kW kW W/W kW kW W/W kW kW W/W
W
5.00 7.84 1.98 3.95 7.38 2.04 3.61 6.96 2.11 3.31 6.58 2.17 3.03 6.17 2.28 2.70 5.67 2.39 2.37
6.00 8.10 2.01 4.03 7.62 2.07 3.67 7.18 2.14 3.36 6.78 2.21 3.08 6.36 2.32 2.75 5.86 2.43 2.41
7.00 8.38 2.05 4.08 7.88 2.12 3.72 7.42 2.18 3.40 7.00 2.25 3.11 6.57 2.36 2.78 6.06 2.48 2.44
8.00 8.64 2.12 4.09 8.12 2.18 3.72 7.63 2.25 3.40 7.20 2.32 3.11 6.76 2.43 2.78 6.24 2.56 2.44
9.00 8.89 2.14 4.16 8.34 2.20 3.79 7.84 2.27 3.45 7.38 2.34 3.15 6.94 2.46 2.83 6.42 2.58 2.49
10.00 9.22 2.17 4.26 8.64 2.23 3.87 8.12 2.30 3.52 7.64 2.38 3.22 7.19 2.49 2.88 6.65 2.62 2.54
11.00 9.48 2.19 4.33 8.88 2.26 3.93 8.33 2.33 3.58 7.83 2.40 3.26 7.38 2.52 2.93 6.83 2.64 2.58
12.00 9.70 2.22 4.37 9.07 2.29 3.96 8.50 2.36 3.60 7.98 2.43 3.28 7.54 2.56 2.95 6.99 2.68 2.60
13.00 9.87 2.24 4.41 9.23 2.31 4.00 8.64 2.38 3.63 8.10 2.45 3.30 7.66 2.58 2.97 7.11 2.70 2.63
14.00 10.12 2.25 4.49 9.45 2.32 4.06 8.84 2.40 3.69 8.28 2.47 3.35 7.83 2.59 3.02 7.28 2.72 2.67
15.00 10.25 2.27 4.52 9.56 2.34 4.09 8.93 2.41 3.71 8.36 2.48 3.37 7.92 2.61 3.04 7.37 2.74 2.69
16.00 10.50 2.29 4.59 9.79 2.36 4.15 9.14 2.43 3.76 8.55 2.51 3.41 8.10 2.63 3.08 7.54 2.76 2.73
17.00 10.64 2.30 4.63 9.90 2.37 4.18 9.24 2.44 3.78 8.63 2.52 3.43 8.19 2.65 3.10 7.64 2.78 2.75
Heating
Ambient temp.(℃)
-10 -6 -2 2 7 10 13
Hot
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
Power
COP
COP
COP
COP
COP
COP
COP
temp.
50.00 3.56 2.01 1.77 4.50 2.28 1.98 5.36 2.53 2.12 6.02 2.75 2.19 6.62 2.90 2.29 7.28 3.07 2.37 8.23 3.32 2.48
21
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
MGC-V10W/D2N1
Cooling
Ambient temp.(℃)
21.00 25.00 30.00 35.00 40.00 46.00
Chilled
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
EER
EER
EER
EER
EER
EER
temp.
W/
(℃) kW kW W/W kW kW kW kW W/W kW kW W/W kW kW W/W kW kW W/W
W
5.00 11.20 2.60 4.31 10.54 2.68 3.94 9.95 2.76 3.60 9.40 2.85 3.30 8.81 2.99 2.95 8.10 3.14 2.58
6.00 11.57 2.64 4.39 10.89 2.72 4.00 10.26 2.80 3.66 9.69 2.89 3.35 9.09 3.04 2.99 8.37 3.19 2.63
7.00 11.98 2.69 4.45 11.26 2.78 4.06 10.60 2.86 3.70 10.00 2.95 3.39 9.39 3.10 3.03 8.66 3.25 2.66
8.00 12.35 2.77 4.45 11.59 2.86 4.06 10.91 2.95 3.70 10.28 3.04 3.38 9.66 3.19 3.03 8.92 3.35 2.66
9.00 12.70 2.80 4.53 11.91 2.89 4.13 11.19 2.98 3.76 10.54 3.07 3.44 9.92 3.22 3.08 9.16 3.38 2.71
10.00 13.18 2.84 4.64 12.35 2.93 4.22 11.60 3.02 3.84 10.91 3.11 3.50 10.28 3.27 3.14 9.51 3.43 2.77
11.00 13.54 2.87 4.72 12.68 2.96 4.29 11.90 3.05 3.90 11.18 3.14 3.56 10.54 3.30 3.19 9.76 3.47 2.82
12.00 13.85 2.91 4.76 12.96 3.00 4.32 12.15 3.09 3.92 11.41 3.19 3.57 10.77 3.35 3.21 9.98 3.52 2.84
13.00 14.10 2.94 4.80 13.18 3.03 4.36 12.34 3.12 3.96 11.58 3.22 3.60 10.94 3.38 3.24 10.15 3.55 2.86
14.00 14.45 2.96 4.89 13.49 3.05 4.43 12.62 3.14 4.02 11.83 3.24 3.65 11.19 3.40 3.29 10.40 3.57 2.91
15.00 14.64 2.97 4.93 13.66 3.06 4.46 12.76 3.16 4.04 11.95 3.25 3.67 11.32 3.42 3.31 10.52 3.59 2.93
16.00 15.00 3.00 5.00 13.98 3.09 4.52 13.05 3.19 4.09 12.21 3.29 3.72 11.58 3.45 3.35 10.78 3.62 2.97
17.00 15.19 3.01 5.04 14.15 3.11 4.55 13.20 3.20 4.12 12.33 3.30 3.73 11.71 3.47 3.37 10.91 3.64 3.00
Heating
Ambient temp.(℃)
-10 -6 -2 2 7 10 13
Hot
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
Power
COP
COP
COP
COP
COP
COP
COP
temp.
41.00 6.61 2.00 3.30 8.27 2.28 3.63 9.74 2.53 3.85 10.83 2.75 3.94 11.79 2.90 4.07 13.18 3.07 4.29 15.13 3.32 4.56
42.00 6.42 2.05 3.14 8.04 2.32 3.46 9.48 2.58 3.67 10.56 2.81 3.76 11.50 2.96 3.89 12.84 3.13 4.10 14.71 3.38 4.35
43.00 6.26 2.09 3.00 7.86 2.37 3.31 9.28 2.64 3.52 10.34 2.86 3.61 11.28 3.02 3.74 12.56 3.20 3.93 14.37 3.45 4.16
44.00 6.14 2.13 2.88 7.71 2.42 3.19 9.12 2.69 3.39 10.18 2.92 3.48 11.11 3.08 3.61 12.35 3.26 3.79 14.11 3.52 4.00
45.00 6.05 2.17 2.78 7.61 2.47 3.08 9.01 2.74 3.28 10.07 2.98 3.37 11.00 3.14 3.50 12.21 3.33 3.67 13.92 3.59 3.87
46.00 5.93 2.20 2.70 7.47 2.49 3.00 8.85 2.77 3.19 9.90 3.01 3.29 10.84 3.17 3.42 12.01 3.36 3.57 13.66 3.63 3.76
47.00 5.76 2.24 2.57 7.26 2.54 2.85 8.61 2.83 3.05 9.65 3.07 3.14 10.56 3.23 3.27 11.68 3.43 3.41 13.27 3.70 3.58
48.00 5.53 2.31 2.40 6.98 2.62 2.66 8.29 2.91 2.85 9.30 3.17 2.94 10.19 3.33 3.06 11.25 3.53 3.19 12.76 3.81 3.35
49.00 5.23 2.40 2.18 6.61 2.73 2.43 7.86 3.03 2.60 8.82 3.29 2.68 9.68 3.47 2.79 10.67 3.67 2.91 12.08 3.97 3.05
50.00 4.89 2.52 1.94 6.19 2.86 2.16 7.37 3.18 2.32 8.28 3.46 2.40 9.10 3.64 2.50 10.01 3.86 2.60 11.32 4.17 2.72
22
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
MGC-V12W/D2RN1
Cooling
Ambient temp.(℃)
21.00 25.00 30.00 35.00 40.00 46.00
Chilled
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
EER
EER
EER
EER
EER
EER
temp.
W/
(℃) kW kW W/W kW kW kW kW W/W kW kW W/W kW kW W/W kW kW W/W
W
5.00 12.54 2.98 4.21 11.81 3.07 3.85 11.14 3.16 3.52 10.53 3.26 3.23 9.86 3.42 2.88 9.08 3.60 2.52
6.00 12.96 3.02 4.29 12.19 3.12 3.91 11.49 3.21 3.58 10.85 3.31 3.28 10.18 3.48 2.93 9.38 3.65 2.57
7.00 13.41 3.08 4.35 12.61 3.18 3.96 11.87 3.28 3.62 11.20 3.38 3.31 10.52 3.55 2.96 9.70 3.73 2.60
8.00 13.83 3.18 4.35 12.99 3.28 3.96 12.22 3.38 3.62 11.51 3.48 3.31 10.82 3.66 2.96 9.99 3.84 2.60
9.00 14.22 3.21 4.43 13.34 3.31 4.03 12.54 3.41 3.68 11.80 3.52 3.36 11.11 3.69 3.01 10.26 3.88 2.65
10.00 14.76 3.26 4.53 13.83 3.36 4.12 12.99 3.46 3.75 12.22 3.57 3.42 11.51 3.75 3.07 10.65 3.93 2.71
11.00 15.17 3.29 4.61 14.20 3.39 4.19 13.32 3.49 3.81 12.52 3.60 3.48 11.81 3.78 3.12 10.94 3.97 2.75
12.00 15.52 3.34 4.65 14.52 3.44 4.22 13.60 3.55 3.84 12.77 3.66 3.49 12.06 3.84 3.14 11.18 4.03 2.77
13.00 15.79 3.36 4.70 14.76 3.47 4.26 13.82 3.57 3.87 12.97 3.69 3.52 12.25 3.87 3.17 11.37 4.06 2.80
14.00 16.19 3.39 4.78 15.11 3.49 4.33 14.14 3.60 3.93 13.25 3.71 3.57 12.54 3.90 3.22 11.65 4.09 2.85
15.00 16.39 3.40 4.82 15.29 3.51 4.36 14.29 3.62 3.95 13.38 3.73 3.59 12.67 3.92 3.24 11.79 4.11 2.87
16.00 16.80 3.44 4.89 15.66 3.54 4.42 14.62 3.65 4.00 13.68 3.77 3.63 12.97 3.95 3.28 12.07 4.15 2.91
17.00 17.02 3.45 4.93 15.85 3.56 4.45 14.78 3.67 4.03 13.81 3.78 3.65 13.11 3.97 3.30 12.22 4.17 2.93
Heating
Ambient temp.(℃)
-10 -6 -2 2 7 10 13
Hot
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
Power
COP
COP
COP
COP
COP
COP
COP
temp.
42.00 7.17 2.42 2.96 8.99 2.75 3.26 10.60 3.06 3.46 11.81 3.33 3.55 12.86 3.50 3.67 14.35 3.71 3.87 16.45 4.01 4.10
43.00 7.00 2.47 2.83 8.78 2.81 3.13 10.37 3.12 3.32 11.56 3.39 3.41 12.61 3.57 3.53 14.05 3.79 3.71 16.07 4.09 3.93
44.00 6.87 2.52 2.72 8.63 2.87 3.01 10.20 3.19 3.20 11.38 3.46 3.29 12.42 3.65 3.41 13.81 3.86 3.57 15.78 4.17 3.78
45.00 6.77 2.58 2.63 8.51 2.93 2.91 10.07 3.25 3.10 11.25 3.53 3.18 12.30 3.72 3.31 13.65 3.94 3.46 15.56 4.26 3.65
46.00 6.63 2.60 2.55 8.36 2.96 2.83 9.90 3.28 3.01 11.07 3.57 3.10 12.12 3.76 3.22 13.42 3.98 3.37 15.28 4.30 3.55
47.00 6.44 2.65 2.43 8.12 3.01 2.69 9.63 3.35 2.88 10.78 3.64 2.96 11.81 3.83 3.08 13.06 4.06 3.22 14.84 4.39 3.38
48.00 6.18 2.73 2.26 7.81 3.10 2.51 9.27 3.45 2.69 10.40 3.75 2.77 11.40 3.95 2.89 12.58 4.18 3.01 14.27 4.52 3.16
49.00 5.85 2.84 2.06 7.39 3.23 2.29 8.79 3.59 2.45 9.87 3.90 2.53 10.83 4.11 2.64 11.93 4.35 2.74 13.51 4.70 2.87
50.00 5.47 2.98 1.83 6.93 3.39 2.04 8.24 3.77 2.19 9.26 4.09 2.26 10.18 4.31 2.36 11.20 4.57 2.45 12.65 4.93 2.56
23
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
Cooling
MGC-V14W/D2RN1
Ambient temp.(℃)
21.00 25.00 30.00 35.00 40.00 46.00
Chilled
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
EER
EER
EER
EER
EER
EER
temp.
W/
(℃) kW kW W/W kW kW kW kW W/W kW kW W/W kW kW W/W kW kW W/W
W
5.00 13.99 3.43 4.07 13.18 3.54 3.72 12.43 3.65 3.41 11.75 3.76 3.12 11.01 3.95 2.79 10.13 4.15 2.44
6.00 14.47 3.49 4.15 13.61 3.60 3.78 12.83 3.71 3.46 12.11 3.82 3.17 11.36 4.01 2.83 10.46 4.21 2.48
7.00 14.97 3.56 4.21 14.07 3.67 3.83 13.25 3.78 3.50 12.50 3.90 3.21 11.74 4.10 2.87 10.82 4.30 2.52
8.00 15.43 3.67 4.21 14.49 3.78 3.83 13.63 3.90 3.50 12.85 4.02 3.20 12.08 4.22 2.86 11.15 4.43 2.52
9.00 15.87 3.70 4.29 14.89 3.82 3.90 13.99 3.93 3.56 13.18 4.06 3.25 12.40 4.26 2.91 11.46 4.47 2.56
10.00 16.47 3.76 4.38 15.44 3.87 3.99 14.50 3.99 3.63 13.64 4.12 3.31 12.85 4.32 2.97 11.88 4.54 2.62
11.00 16.93 3.79 4.46 15.85 3.91 4.05 14.87 4.03 3.69 13.98 4.16 3.36 13.18 4.37 3.02 12.20 4.58 2.66
12.00 17.32 3.85 4.50 16.20 3.97 4.08 15.18 4.09 3.71 14.26 4.22 3.38 13.46 4.43 3.04 12.48 4.65 2.68
13.00 17.63 3.88 4.54 16.47 4.00 4.12 15.43 4.12 3.74 14.47 4.25 3.40 13.67 4.46 3.06 12.69 4.69 2.71
14.00 18.07 3.91 4.62 16.87 4.03 4.19 15.78 4.15 3.80 14.79 4.28 3.45 13.99 4.50 3.11 13.00 4.72 2.75
15.00 18.30 3.93 4.66 17.07 4.05 4.22 15.95 4.17 3.82 14.94 4.30 3.47 14.15 4.52 3.13 13.15 4.74 2.77
16.00 18.75 3.97 4.73 17.48 4.09 4.27 16.32 4.22 3.87 15.27 4.35 3.51 14.47 4.56 3.17 13.47 4.79 2.81
17.00 18.99 3.99 4.77 17.68 4.11 4.30 16.50 4.24 3.89 15.42 4.37 3.53 14.63 4.59 3.19 13.64 4.81 2.83
Heating
Ambient temp.(℃)
-10 -6 -2 2 7 10 13
Hot
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
Power
COP
COP
COP
COP
COP
COP
COP
temp.
42.00 8.05 2.77 2.91 10.09 3.15 3.21 11.90 3.50 3.40 13.25 3.80 3.49 14.43 4.00 3.61 16.10 4.24 3.80 18.46 4.58 4.03
43.00 7.86 2.83 2.78 9.86 3.21 3.07 11.64 3.57 3.26 12.97 3.88 3.35 14.15 4.08 3.47 15.76 4.33 3.64 18.03 4.67 3.86
44.00 7.70 2.88 2.67 9.68 3.28 2.95 11.44 3.64 3.14 12.77 3.96 3.23 13.94 4.17 3.35 15.50 4.41 3.51 17.70 4.77 3.71
45.00 7.59 2.94 2.58 9.55 3.34 2.86 11.30 3.71 3.04 12.63 4.04 3.13 13.80 4.25 3.25 15.32 4.51 3.40 17.46 4.87 3.59
46.00 7.44 2.97 2.51 9.37 3.38 2.78 11.11 3.75 2.96 12.42 4.08 3.05 13.59 4.29 3.17 15.06 4.55 3.31 17.14 4.91 3.49
47.00 7.22 3.03 2.38 9.11 3.44 2.64 10.81 3.83 2.82 12.10 4.16 2.91 13.25 4.38 3.03 14.66 4.64 3.16 16.65 5.01 3.32
48.00 6.94 3.12 2.22 8.76 3.55 2.47 10.40 3.94 2.64 11.66 4.28 2.72 12.79 4.51 2.84 14.12 4.78 2.95 16.01 5.16 3.10
49.00 6.56 3.25 2.02 8.29 3.69 2.25 9.86 4.10 2.41 11.07 4.46 2.48 12.15 4.69 2.59 13.39 4.97 2.69 15.16 5.37 2.82
50.00 6.14 3.41 1.80 7.77 3.87 2.01 9.25 4.30 2.15 10.39 4.68 2.22 11.42 4.92 2.32 12.56 5.22 2.41 14.20 5.64 2.52
24
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
MGC-V16W/D2RN1
Cooling
Ambient temp.(℃)
21.00 25.00 30.00 35.00 40.00 46.00
Chilled
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
EER
EER
EER
EER
EER
EER
temp.
W/
(℃) kW kW W/W kW kW kW kW W/W kW kW W/W kW kW W/W kW kW W/W
W
5.00 16.23 3.99 4.07 15.29 4.11 3.72 14.42 4.24 3.40 13.63 4.37 3.12 12.77 4.59 2.78 11.75 4.82 2.44
6.00 16.78 4.05 4.14 15.79 4.18 3.78 14.88 4.31 3.46 14.05 4.44 3.16 13.18 4.66 2.83 12.14 4.89 2.48
7.00 17.37 4.13 4.20 16.32 4.26 3.83 15.37 4.39 3.50 14.50 4.53 3.20 13.62 4.76 2.86 12.55 4.99 2.51
8.00 17.90 4.26 4.20 16.81 4.39 3.83 15.82 4.53 3.49 14.91 4.67 3.19 14.01 4.90 2.86 12.93 5.14 2.51
9.00 18.41 4.30 4.28 17.27 4.43 3.90 16.23 4.57 3.55 15.28 4.71 3.24 14.38 4.95 2.91 13.29 5.19 2.56
10.00 19.11 4.36 4.38 17.91 4.50 3.98 16.81 4.64 3.63 15.82 4.78 3.31 14.90 5.02 2.97 13.78 5.27 2.61
11.00 19.64 4.41 4.46 18.39 4.54 4.05 17.25 4.68 3.68 16.21 4.83 3.36 15.29 5.07 3.02 14.16 5.32 2.66
12.00 20.09 4.47 4.49 18.79 4.61 4.08 17.61 4.75 3.71 16.54 4.90 3.38 15.61 5.14 3.03 14.47 5.40 2.68
13.00 20.45 4.51 4.54 19.11 4.65 4.11 17.89 4.79 3.74 16.79 4.94 3.40 15.86 5.19 3.06 14.72 5.45 2.70
14.00 20.96 4.54 4.62 19.57 4.68 4.18 18.30 4.82 3.79 17.15 4.97 3.45 16.23 5.22 3.11 15.08 5.48 2.75
15.00 21.23 4.56 4.65 19.80 4.70 4.21 18.50 4.85 3.82 17.33 5.00 3.47 16.41 5.25 3.13 15.26 5.51 2.77
16.00 21.75 4.61 4.72 20.27 4.75 4.27 18.93 4.90 3.87 17.71 5.05 3.51 16.79 5.30 3.17 15.63 5.57 2.81
17.00 22.03 4.63 4.76 20.51 4.77 4.30 19.14 4.92 3.89 17.88 5.07 3.53 16.97 5.33 3.19 15.82 5.59 2.83
Heating
Ambient temp.(℃)
-10 -6 -2 2 7 10 13
Hot
water
outlet
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Capacity
Power
Power
Power
Power
Power
Power
Power
COP
COP
COP
COP
COP
COP
COP
temp.
25
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
46
O U T SID E A IR T EM PERAT U RE
35
20
-5
-10 45 7 15 20 C
DELIVERY WATER TEMPERATURE
HEATING
C
27
O U T SID E A IR T EM PERAT U RE
20
-3
-15
30 35 45 55 C
DELIVERY WATER TEMPERATURE
Water and ethylene glycol solutions used as a thermal vector in the place of water reduce the performance
of the unit. Multiply the performance figures by the values given in the following table.
26
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
Note:
1. During winter leaving the unit unused, please drain water out completely from unit if no anti-freeze were
charged into pipeline, or keep power on (at standby or off status) and ensure that water is contained inside
of unit.
2. When ambient temperature lower 5℃, running cooling mode must be charged antifreeze. Refers to upper
parameters for the charged volume.
b) Fouling Factors
The performance data given refer to conditions with clean evaporator plates (fouling factor=1). For different
fouling factors, multiply the figures in the performance tables by the coefficient given in the following table.
Fouling factors Evaporator
2
(m °C/W) f1 fk1 fx1
-5
4.4×10 - - -
-4
0.86×10 0.96 0.99 0.99
-4
1.72×10 0.93 0.98 0.98
f1 correction factor of capacity
fk1 power input correction factor of compressor
fx1 correction factor of total power input
27
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
MGC-V10W/D2N1
28
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
MGC-V12W/D2RN1
MGC-V14W/D2RN1
29
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
MGC-V16W/D2RN1
30
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
O u td o o r U n it
M ic r o
1 .4 m
1 .0 m
31
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
MGC-V5W/D2N1, MGC-V7W/D2N1
32
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
28.4
28.5 28.6
28.7 28.3
28.1 28.2
33
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
MGC-V10W/D2N1
34
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
25.6
25.9
25.1
25.2 25.7
25.3
25.8
25.4 25.5
35
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
36
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
25.4
25.9
25.1
25.5
25.2
25.3
25.6
25.10 25.8
25.7
25.11
37
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
15. Installation
a) Installation of general information
General warning
1. These units have been designed to chilled and hot water and must be used in applications compatible with
their performance characteristics; these appliances are designed for residential or similar applications.
2. Incorrect installation, regulation and maintenance or improper use absolves the manufacturer from all
liability, whether contractual or otherwise, for damage to people, animals or things. Only those
applications specifically indicated in this list are permitted.
3. Read this manual carefully. All work must be carried out by qualified personnel in conformity with
legislation in force in the country concerned.
4. The guarantee is invalidated if the above instructions are not respected and if the unit is started up for the
first time without the presence of personnel authorized by the Company (where specified in the supply
contract) who should draw up a“ start-up” report.
5. The documentation supplied with the unit must be consigned to the owner who should keep it carefully for
future consultation in the event of maintenance or service.
6. All repair or maintenance work must be carried out by the Company’s Technical Service or qualified
personnel following the instructions in this manual. The air-conditioner must under no circumstances be
modified or tampered with as this may create situations of risk. Failure to observe this condition absolves
the manufacturer of all liability for resulting damage.
Prohibition
1. This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
2. Do not touch the unit with bare feet or with wet or damp parts of the body.
3. Do not carry out cleaning operations without first disconnecting the system from the electricity supply.
4. Do not modify safety or regulation devices without authorization and instructions from the manufacturer.
5. Do not pull, detach or twist the electrical cables coming from the unit, even when disconnected from the
mains electricity supply.
6. Do not open doors or panels providing access to the internal parts of the unit without first ensuring that the
mains switch is in the off position.
7. Do not introduce pointed objects through the air intake and outlet grills.
8. Do not dispose of, abandon or leave within reach of children packaging materials (cardboard, staples,
plastic bags, etc.) as they may represent a hazard.
Important
1. The chiller appliances are supplied without the main switch. The power supply to the unit must be
disconnected using a suitable main switch that must be supplied and installed by the installer.
2. Respect safety distances between the unit and other equipment or structures. Guarantee adequate space
for access to the unit for maintenance and/or service operations.
Power supply: the cross section of the electrical cables must be adequate for the power of the unit and the
power supply voltage must correspond with the value indicated on the respective units. All units must be
earthed in conformity with legislation in force in the country concerned.
3. Hydraulic connections should be carried out as indicated in the instructions to guarantee correct operation
of the unit. Empty the water circuit or add glycol if the unit is not used during the winter.
Handle the unit with the utmost care to avoid damage.
38
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
Positioning
Before handling the unit, check the capacity of the lifting equipment used, respecting the instructions on the
packaging.
To move the unit in the horizontal, make appropriate use of a lift truck or similar, bearing in mind the weight
distribution of the unit. To lift the unit, insert tubes long enough to allow positioning of the lifting slings and
safety pins in the feet on the unit.
To avoid the slings damaging the unit, place protection between the slings and the unit. Position the unit in
the site indicated by the customer. Place either a layer of rubber (min. thickness 10 mm) or vibration damper
feet (optional) between the base and support surface. Fix the unit, making sure it is level and that there is
easy access to hydraulic and electrical components. If the site of installation is exposed to strong winds, fix
the unit adequately to the support surface using tie rods if necessary. If a heat pump unit is being installed,
make sure the condensate is drained using the drain hose supplied as standard. Prevent leaves, branches
or snow from accumulating around the unit. These could reduce the efficiency of the unit.
39
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
>60cm
Air inlet
>300 Maintain
channel
Air inlet >600
>2000
Air outlet
>300
>600
>2000
All the pictures in this manual are for explanation purpose only. They may be slightly different from the air conditioner you
purchased (depend on model).The actual shape shall prevail.
40
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
d) Hydraulic connection
The choice and installation of components is the responsibility of the installer who should follow good
working practice and current legislation. Before connecting the pipes, make sure they do not contain stones,
sand, rust, or others which might damage the unit. Construction of a bypass is recommended to enable the
pipes to be washed through without having to disconnect the unit (see drain valves). The connection piping
should be supported in such a way as to avoid it weighing on the unit. It is recommended that the following
devices are installed in the water circuit of the evaporator. A hydraulic safety valve shall be mounted in water
system, which should open constantly.
2 1
4
7
11
10 6 13 WATER INLET
A
5
9
8 7 14
11
10 12 F WATER OUTLET
9 9
If the installation requires a useful head higher than that obtained by installing a pump assembly and storage
tank, it is recommended that an additional pump is installed on the unit. Provided the additional pump
installed inside of unit, the pump must connected close to plate heat exchanger. Provided the pump installed
outside of unit, the pump shall be connected at water pipe’s outlet. The pump can be easily installed on the
unit by removing the pump connection pipe. Connect to terminal PL,PN on the electric panel.
Important
1) The chillers must be provided with a filling/top-up system connected to the return line and a drain cock in
the lowest part of the installation. Installations containing anti-freeze or covered by specific legislation
must be fitted with hydraulic disconnections.
2) The manufacturer is not liable for obstruction, breakage or noise resulting from the failure to install filters
or vibration dampers. Particular types of water used for filling or topping up must be treated with
appropriate treatment systems. For reference values, see the table.
kW is the unit for cooling capacity, L is the unit for (G) minimum water flow volume in the formula.
Comfortable type air conditioner
G= cooling capacity×2.6L
Process type cooling
G= cooling capacity×7.4L
In certain occasion (especially in manufacture cooling process), for conforming the system water
content requirement, it’s necessary to mount a tank equipping with a cut-off baffle at the system to avoid
water short-circuit, Please see the following schemes:
Error Recommendation
Error Recommendation
42
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
For minimum chilled water flow rate For maximum chilled water flow rate
Evaporator
Evaporator
Recirculation
Recirculation
If a closed expansion tank with its filled volume of air is too small, the system pressure will easily exceed the
maximum allowable pressure and cause water to discharge from the pressure relief valve, thus wasting
water. If the closed tank is too large, when the water temperature drops, the system pressure may decrease
to a level below the minimum allowable value and cause trouble in the air vent. Therefore, accurate sizing of
a closed expansion tank is essential.
For diaphragm expansion tanks, the minimum volume of the water tank, Vt, gal(m3),can be calculated by the
following formula, recommended by ASHRAE Handbook 1996, HVAC Systems and Equipment:
Vt=Vs v2/v1-1-3α(T2-T1)
1-p1/p2
T1=lower temperature,oF (℃)
T2=higher temperature, oF (℃)
Vs=volume of water in system, gal(m3)
p1=absolute pressure at lower temperature,psia(kPa abs.)
p2=absolute pressure at higher temperature,paia(kPa abs.)
v1,v2=specific volume of water at lower and higher temperature, respectively, ft3/lb(m3/kg)
α=linear coefficient of thermal expansion; for steel, α=6.5x10-6in./in·oF(1.2x10-5per ℃); for copper,
α=9.5x10-6in./in·oF(1.7x10-5per ℃)
In a chilled water system, the higher temperature T2 is the highest anticipated ambient temperature when
43
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
the chilled water system shuts down during summer. The lower temperature in a heating system is often the
ambient temperature at fill conditions(for example, 50 oF or 10℃).
PH 6-8
Total hardness less than 50 ppm
Electrical conductivity less than 200 mV/cm (25°C)
Sulfide ion none
Chlorine ions less than 50 ppm
Ammonia ions none
Sulfate ion less than 50 ppm
Silicon less than 30 ppm
Total iron less than 0.3 ppm
Sodium ion No requirement
Calcium ion less than 50 ppm
44
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
security discharge
water outlet
D
C
F
B
G
A
Water outlet of plate heat exchanger E
H
auto-water
replenishing orifice
water outlet
water inlet security discharge
A
B
C
D
E
F
Water
A B C D E F Auto-water Security
Model inlet/outlet
(mm) (mm) (mm) (mm) (mm) (mm) replenishing (Ø) discharge (Ø)
(Ø)
MGC-V10W/D2N1
MGC-V12W/D2RN1
300 195 155 105 68 105 R5/4 G1/2 G1/2
MGC-V14W/D2RN1
MGC-V16W/D2RN1
Important
a) The installation must be filled to a pressure of between 1 and 2 bars.
b) It is recommended that this operation be repeated after the unit has been operating for a number of hours.
The pressure of the installation should be checked regularly and if it drops below 1 bar, the water content
should be topped-up.
c) Check the hydraulic tightness of joints.
d) An all-pole disconnection device which has at least 3mm separation distance in all pole and a residual
current device (RCD) with the rating of above 10mA shall be incorporated in the fixed wiring according to
the national rule the appliance shall be installed in accordance with national wiring regulations.
e) If the fluid in the circuit contains anti-freeze, it should not be allowed to drain freely as it is pollutant. It
should be collected for possible reuse. When draining after heat pump operation, take care as the water
may be hot (up to 50°).
45
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
Important
Power to the unit must be turned on only after installation work (hydraulic and electrical) has been
completed.
All electrical connections must be carried out by qualified personnel in accordance with legislation in
force in the country concerned.
Respect instructions for connecting phase, neutral and earth conductors.
The power line should be fitted upstream with a suitable device to protect against short-circuits and
leakage to earth, isolating the installation from other equipment.
Voltage must be within a tolerance of ±10% of the rated power supply voltage for the unit (for three
phase units, the unbalance between the phases must not exceed 3%).If these parameters are not
respected, contact the electricity supply company.
For electrical connections, use double insulation cable in conformity with current legislation in the
country concerned.
An omnipolar thermal overload switch and a lockable mains disconnecting switch, in compliance with
the CEI-EN standards (contact opening of at least 3mm), with adequate switching and residual
current protection capacity based on the electrical data table shown below, must be installed as near
as possible to the appliance.
The devices on the unit must be lockable. An efficient earth connection is obligatory. Failure to earth
the appliance absolves the manufacturer of all liability for damage.
Do not use water pipes to earth the unit.
Electrical Panel
The electrical panel is located inside the unit at the top of the technical compartment where the various
components of the refrigerant circuit are also to be found.
To access the electrical panel, remove the front panel of the unit by undoing the screws.
5/7kW 10~16kW
46
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
1) MGC-V5W/D2N1, MGC-V7W/D2N1
Power Cable
Power Supply
L
N
Outdoor units GND
Residual Current
CIrcuit-breaker
For the functional connection of the unit, bring the power supply cable to the electrical panel inside the unit
and connect it to terminals L-N and respecting the (L) phase, (N) neutral and earth in the case of
single phase units (220-240V~50Hz).
2) MGC-V10W/D2N1
L N GND 1 2 3 4 5 6 7 8 9 10 11
L N GND
Residual Current
Circuit-breaker
L N GND
AC 220-240V 50Hz
NOTE: The outdoor units must be installed with an Residual Current Circuit-breaker near the power supply
and must be effectively earthed.
47
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
A B C N GND 1 2 3 4 5 6 7 8 9 10 11
A B C N GND
Residual Current
Circuit-breaker
A B C N GND
AC 380-415V 50Hz
Auxiliary Connection
1) MGC-V5W/D2N1, MGC-V7W/D2N1
1 2 1 2 L 1
PUMP2 BOIL ON/OFF
L
220~240 V
N
L
220~240 V
N
AC CAN TACTOR
1.“PUMP2”wiring terminal supplies ON/OFF signals only. Standby water pump must be controlled by the AC
contactor.
2.“ON/OFF” wiring terminal L supplies 220V voltage.
The unit must be powered off when connecting the remote control switch.
When the remote control switch is closed, the unit is forced to shut down.
48
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
a. Additional pump
Main control board
1 2
L
220-240V
N
L
220-240V
N A1
AC contactor
A2
Additional pump
b. Remote alarm
3 4
c. Remote shutdown
5 6
SWITCH
49
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
d. Remote cooling/heating
7 8
SWITCH 2
If switch 2 is closed, the unit will shift to heating mode forcibly;
If switch 2 breaks, the unit will shift to cooling mode forcibly.
Note:
● Remote shutdown and Remote cooling/heating is optional function.
● Choose this function by DIP switch SW4_1(SW3_1 for 12/14/16kW) on PCB board.
Factory default has no remote cooling/heating.
● When the remote control and wired controller used at the same time, the unit will carry out the last
command of arbitrary terminal.
● Remote shutdown has the highest priority. In the status of remote shutdown, other controllers can’t start
the unit.
e. Remote controller
9 10 11
P Q E
Important
The power cord type designation is H07RN-F.
Connecting cable between indoor unit and outdoor unit shall be approved poly-chloroprene sheathed flexible
cord, type designation H07RN-F or heavier cord.
The means for disconnection from a power supply shall be incorporated in the fixed wiring and have an air
gap.
50
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
51
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
1
3 2
se
t
3
To access the control panel, open the door:
52
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
Pump
The electronic board includes a pump control output. The pump starts when the assembly is powered up
and at least 285 seconds before the compressor starts up and stops 120 seconds after the assembly shuts
down. After the first 120 seconds of pump operation when the water flow is at full speed, the water flow
alarm functions are activated (differential pressure switch and flow switch). With a pump connected to
terminals PL and PN on the installer terminal board.
53
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
b) Routine maintenance
Never perform any cleaning operations before having disconnected the unit from the mains power supply.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified manufacturer or its service agent or a similarly qualified.
Regular maintenance is fundamental to maintain the efficiency of the unit both in terms of operation and
energy consumption. The Technical Assistance Service maintenance plan must be observed, with an
annual service which includes the following operations and checks:
- Filling of the water circuit.
- Presence of air bubbles in the water circuit.
- Efficiency of safety devices.
- Power supply voltage.
- Power input.
- Tightness of electrical and hydraulic connections.
- Condition of the compressor contactor.
- Efficiency of the plate heat exchanger heater.
- Checking of operating pressure, superheating and sub cooling.
- Efficiency of compressor heater.
- Cleaning of finned coil (*).
- Cleaning of fan grills.
- Cleaning of condensate drain pan (if installed).
(*) For “Heat pump” appliances, the checks are to be performed quarterly.
For units installed near the sea, the intervals between maintenance should be halved.
c) Extraordinary maintenance
Never perform any cleaning operations before having disconnected the unit from the mains power supply.
Chemical washing
You are recommended to chemically wash the plate heat exchanger after every 3 years of operation.
Important
In the event of partial leaks, the circuit must be completely emptied before being refilled
The R410a refrigerant must only be filled in the liquid state. Operating conditions other than nominal
conditions may produce considerably different values.
Seal testing or identification of leaks must only be carried out using R410a refrigerant gas, checking with a
suitable leak detector.
54
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
Prohibition
1. The refrigerant circuit must not be filled with a refrigerant other than that indicated of specification.
2. The use of a different refrigerant may cause serious damage to the compressor.
3. Oxygen, acetylene or other inflammable or poisonous gases must never be used in the refrigerant circuit
as they may cause explosion or poisoning.
4. Oils other than those indicated on manual before must not be used. The use of different oils may cause
serious damage to the compressor.
Important
If there is a possibility that the outside temperature may drop below zero, there is the risk of freezing.
The water circuit MUST BE EMPTIED AND SHUT OFF POWER (when draining after heat pump operation
take care as the water may be hot) or antifreeze must be added in the proportion recommended by the
manufacturer.
55
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
18. Controller
18.1 Standard controller
It is built-in with the chiller at the factory.
The front panel of the device functions as the user interface and is used to perform all operations relating to
the device.
11 ① ② ③ ④ ⑤ ⑥
17
23 22
⑧ 18
19
⑨
24 21
20
⑩
7.1 7.2
12 13 14 15 16
The last 2 digits of the nixie tube “ ” icon. If “ ” is constantly light, it will display the current
inlet water temperature. Its’unit is ℃ .When customers do the water temperature setting, icon will
7.2
display the setting water temperature. When checking, “ ” will display the result of checking. When
water heating is broken down or in protection, “ ” display the error code and protection code.
Clock icon
⑧
It will display when finish setting the clock and be extinguished when the clock setting work is done.
Timing on function icon
⑨
will flash when setting timing on. The icon will be constantly light when finish setting.
Timing off function icon
⑩
will flash when setting timing off. The icon will be constantly light when finish setting.
Breakdown light icon
11 When the unit is broken down or under protection, this icon will flash and will be off when malfunction
and protection are eliminated.
Compressor booting indicator icon
12 When booting the compressor, this icon will be constantly light. It will be off when the compressor is
shut down
E-heater booting indicator icon(Reserved)
13 When booting the external E-heater, this icon will be constantly light. It will be off when the external
E-heater is shut down.
Fan booting indicator icon
14
When booting the fan, this icon will be constantly light. It will be off when the fan is shut down.
Water pump booting indicator icon
15 When booting the water pump, this icon will be constantly light. It will be off when the water pump is
shut down.
16 Key freezing icon
56
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
When freezing the keys, this icon will be constantly light. It will be off when unfreezing keys.
Temperature unit icon
17 When the control panel displays temperature, this icon will be constantly light.
Current unit icon
18
When the control panel displays current, this icon will be constantly light.
Time format icon
19 The unit is 12-hour format. “ ”will be constantly light when it is forenoon.
“ ” will be constantly light when it is afternoon
Frequency unit icon
20
It will be constantly light when the control panel displays frequency of the compressor.
ON/OFF and OK button
21 1.Long press “ ” for 3S will power on or off the controller.
2.Press “ ” to confirm the former operation when finishing the setting work.
Mode choice function/Function choice/Back function button
1.Mode choice function. Choose operation mode.
2.Function choice. Long press it for 3s to enter function setting in the main interface.(Clock setting,
22 Timing on and timing off setting)
3.Back to the previous menu. Long press it for 3s to back to previous menu in the function setting
interface. Top menu is the main interface.
Up
23 1.(Value increase)
2.Forward to the previous interface.
Down
24 1.(Value decrease)
2.Backward to the next interface.
1) ON/OFF
The first time to powered on the unit, operation panel displays “OFF”. Long press “ ” for 3s, to unlock
“OFF” status and enter into standby status.
Power on: In the standby status, press “ ” to enter mode choice function. Press “ ” circularly
to choose one kind of “power on” mode, the mode icon will flicker at the moment. Press “ ” to confirm
the power on mode. The unit will run as the chosen mode when the mode icon will be constantly light.
Power off: Press “ ” in the main interface to enter mode choice function and the icon which indicate
the current mode will flicker. Press “ ” circularly to choose power off mode,
“ ” will flicker at this moment. Press “ ” button to confirm the power off mode. By this time, “ ”
will be constantly light and the unit stops.
4) Timing setting
a. Timing on setting
① Long press “ ” for 3s to enter function interface. “ ” clock icon will flicker. Press “ ”again
to enter timing on function. “ ” will flicker and press “ ” to enter timing on setting.
57
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
② At this moment, last 2 digits of the nixie tube display “01” which means the first group setting begins.
Press “ ” to the next step.
③ By this time, mode icon will flicker and press “ ”to choose timing on mode. Press “ ” to confirm
your choice and go to the next step.
④ By this time, the last 2 digits of the nixie tube will flicker and press “ ” or “ ” to adjust temperature
and set the temperature of the inlet water. Press “ ” to confirm and move to the next step.
⑤ By this time, the first 2 digits of the nixie tube will flicker and press “ ” or “ ” to adjust time of timing
on. Press “ ” to confirm and switch to minute setting automatically. The last 2 digits of the nixie
tube will flicker and press “ ” or “ ” to adjust minute setting of timing on.(minimal unit of minute
adjustment: 15 minutes) .
⑥ Press “ ” to confirm. The first group setting is finished and “ ” will be constantly light.
When processing the second timing setting, repeat the 1-2 operation above. When the nixie tube displays
“01” and flicker, press“ ” or “ ” to choose the timing on group. When the nixie tube displays “ 02 ”
which means setting timing on function of the second group.
Refers the timing on setting operation of group 1 to set that of group 2.
● Long press “ ” for 3s to return to the previous interface to reset the parameter during setting clock
timing.
58
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
59
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
Features
a. Touch key operation;
b. LCD displays operation parameters;
c. Multiple timer;
d. Real-time clock (battery life:5~8 years).
18.2.1 Overview
5
1
6
2
7
3
8
4
9
16 MODE 10
11 FUNCTIONS 11
15 12
(Press for 3sec to (Press for 3sec to
cancel timer) unlock)
14 13
①.Operation icon
②.Code area
③.Setting temperature
④.Timing On/Off
⑤.Function Icon
⑥.Unit number
⑦.Water Level Indication(reserved)
⑧.Clock
⑨.Water temp.
⑩.ON/OFF Key
⑪.Left Right Key
⑫.Confirm Key
⑬.Function key
⑭.Add and Reduce key
⑮.Cancel key
⑯.Mode key
1. Operation icon : Indicate unit ON and OFF status; the icon displays when the unit is on and does not
display when the unit is off;
60
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
2. Mode area: Indicate the main unit operating mode; details refer to its’ manual;
5. Function icon
3) : Displays when the unit is needed. Press and hold “MODE” key for 3 seconds to cancel the icon
and timing will restart until next maintenance;
7) : Displays when ambient temperature is low which means the main unit need anti-freezing action;
8) : Displays when no key operation for 2 minutes and all keys are locked. Press and hold “OK” key for
3 seconds to unlock;
9) : Displays when error or protection occurs and means the unit need maintenance by professionals.
6The unit number: The user can set the number, details refer to page 16 of the manual;
7. Water level indication: The reserved icon;
8. Clock: Under normal status displays clock; Under timing setting displays the setting timing, details refer to
page 15 of the manual;
9. Water temperature: Under normal status display water temperature; Under water temperature setting
status displays the setting value; Under check status displays check parameter, details refer to Page 9, 18 of
the manual;
10. ON/OFF key: Turn on and turn off functions, details refer to page 7 of the manual.
11. Right and Left key: Press these keys to check setting water temperature; Press right key to shift to the
next step setting under timing setting status; Press these keys to turn over the unit parameter information
under check status;
12. OK key: Press this key to confirm settings. Press and hold this key for 3 seconds to unlock under
locking status;
13. Function key: Setting water temperature, timing and clock etc, details refer to Page 9-17; Press and hold
this key for 3 seconds to enter check status, details refer to page 18 of the manual;
14. Add and Reduce key: Move up or move down values of temperature, timing etc;
15. Cancel key: Press this key to cancel parameter setting under setting status; Press and hold this key for 3
seconds to cancel timing when timing is valid;
16. Mode key: Power on the cooling function, heating function or water pump function, details refer to Page 8
of the manual.
61
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
1) Press the On/Off key to control On and Off status of the main unit.
2) Under Off status, press the On/Off key “ ” to run the main unit, at that time the LCD of wired controller
will display the operation icon “ ”. The main unit will running as the current setting of the wired controller.
3) Under On status, press the On/Off key “ ” to turn off the main unit and the operation icon “ ” on the
LCD will disappear.
ONLINE
QUANTIT Y
RUN
WATER
TEM P.
TIMER
FUNCTIONS
Cooling
→ Heating → Water pump
Press “OK” key or wait for 7 seconds to confirm. During the setting process pressing the “CANCEL” key
to exit without saving.
RUN
WATER
TEMP.
TIMER
MODE
FUNCTIONS
62
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
RUN
WATER
TEMP.
TIMER
ON
MODE
Press
once
FUNCTIONS
Water temperature setting check: To check the water temperature setting value, press the “ ” or “ ”key
▲
under the main page(the page displayed after the controller is powered on).
Water temperature
→ Timing → Clock → Unit NO.
→ Water pump forced
1) Timing setting: 3 timing periods can be set on the wired controller: Timer 1, Timer 2, Timer 3. These 3
timers can control the main unit to be turned ON and OFF 3 times at most during a day.
2) Setting method: press “FUNCTIONS” key under main page twice to enter timing setting. Then the LCD
will display as the following:
TIMER 1
ON
63
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
RUN
WATER
TEMP.
TIMER
ON
MODE
Press
twice
FUNCTIONS
At this time the hour of the clock will flash, which means the current setting is the hour of Timer 1 “On”,
press the “▲” or “▼” to adjust, press “ ” key when finished, and then the minute of the clock will
▲
flash, which means the current setting is the minute of Timer 1 “On”, press the “▲” or “ ▼ ” to adjust,
press “ ” key when finished, the LCD will display as the following:
▲
TIMER 1
OFF
At this time the hour of the clock will flash, which means the current setting is the hour of Timer 1 “Off”,
press the “▲” or “▼” to adjust, press “ ” key when finished, and then the minute of the clock will
▲
flash, which means the current setting is the minute of Timing 1 “Off”, press the “▲” or “▼” to adjust,
press “ ” key when finished, the LCD will display as the following:
▲
TIMER
ON
At this time the hour of the clock will flash, it means the current setting is the hour of the Timer 2 “On”.
And the follow setting method will be the same as the Timer 1. Similarly, the setting of Timing 3 is the
same as this method. After setting is finished, press “OK” key or wait for 7 seconds to confirm the setting,
and the LCD will display the effective timing information, as the following display:
TIMER
64
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
▼
Press “ ” key to enter minute setting interface of
“Timer 1 On”, adjust the minute number to be 10
▼
Press “ ” key to enter hour setting interface of
“Timer 1 Off”, adjust the hour number of “Timer 1 “Timer 1” setting
Off” to be 12 failed, after 7
seconds, the
page shift to the
▼
No No
▼
Whether press “OK” key Whether press “ ” key
Yes Yes
Successfully set the On time of Finish setting the On time of
“Timer 1” to be 07:10 and Off time “Timer 1” to be 07:10 and Off
of “Timer 1 Off ” to be 12:30, then time to be 12:30, then enter the
back to the main page. setting of “Timer 2”.
The setting steps of “Timer 2” and “Timer 3” are the same as “Timer 1”,
after setting all the settings then press “OK” key, the 3 timing periods will
be effective.
During any period of timing setting to press “OK” key , the timing periods which have been set will be
effective (only if the “On” and “Off” of one timing period have been set, the setting is effective).
Check timing information: to check the timing which has been set, press “ ” or “ ” key under main page,
▲
the “ On ”and “ Off ” time of Timer1, Timer 2 and Timer3 will be displayed in turns.
Cancel timing: press and hold “CANCEL” key for 3 seconds, then all the effective timing periods will be
cancelled.
Note: Correct: To avoid timing error, each period of timing should not be crossed. E.g.:
Correct:
TIMER 1 TIMER 2 TIMER 3
65
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
d. Setting clock
RUN
WATER
TEMP.
TIMER
ON
MODE
Press 3
times
FUNCTIONS
Press the “FUNCTION” key 3 times to enter clock setting. The hour of the clock will flash, which means
the current setting is the hour of the clock, press the “▲” or “▼” to adjust, press “ ” key when
▲
finished, and then the minute of the clock will flash, it means the current setting is the minute of the clock,
press the “▲” or “▼” to adjust, press “ OK ” key when finished or wait for 7 seconds to confirm.
During the setting process pressing the “CANCEL” key to exit without saving.
NOTE: To get the correct timing On and timing Off time, please correctly set the clock!
RUN
WATER
TEMP.
TIMER
ON
MODE
Press 4
times
FUNCTIONS
Press the “FUNCTIONS” key 4 times to enter the unit number setting. Press “▲” or “▼” to adjust
the unit number. press “ OK ”key when finished or wait for 7 seconds to confirm. During the setting
process pressing the “CANCEL” key to exit without saving. The setting value is 0-18.
66
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
WATER
TEMP.
TIMER
ON
MODE
Press 5
times
FUNCTIONS
Press the “FUNCTIONS” key 5 times to force open the water pump. The water pump icon will flash.
Press “ OK ”key to confirm. During the setting process pressing the “CANCEL” key to exit without saving.
Note:
a. Forcing water pump function is only limited to stand-by mode, others modes not response.
b. Under forcing water pump function, other settings will not responsible, except stopping
c. When communication disconnects, it will show E2 error in 2 minutes, the wired controller will
automatically cancel the forcing water pump function; while connected, the wired controller keeps
synchronizing with the unit( If forcing water pump function is still on-going, the controller keeping showing
its status).
d. The outdoor unit does not response after activating the forcing water pump function, (eg: forcing water
pump function cannot be activated under forcing heating in stand-by mode),the function will be
automatically stopped if it is not activated within 5 minutes.
check CHECK
icon
Unit number
RUN
check
parameter
check sequence
number
MODE
Press
FUNCTIONS
3 seconds
67
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
68
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
19.Troubleshooting
19.1 PCB parts instructions
MGC-V5W/D2N1, MGC-V7W/D2N1
PFC&IPM panel
7 8 9
6
5
4
3
10
2 1 12 11
1. Input rectifier bridge port 1
2. Input rectifier bridge port 2
3. PFC inductance port 1
4. P-OUT
5. PFC inductance por 2
6. N-OUT
7. PFC control port
8. +18V port
9. IPDU communication port
10. IPM power port N
11. Compressor connection port U/V/W
12. IPM power port P
69
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
70
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
DC filter panel
1
2
3
5
4
71
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
MGC-V10W/D2N1
Main control panel
27 28 30 31 33
29 32
1
26
2
25
3
4
24
5.1
5.2
23 6
7.1
22 7.2
21 8
20 9
19 10
18
11
17
16
12
15 13
14
72
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
PFC Module
12
1
2
3
4
5
11
10
9 8 7 6
73
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
MGC-V12W/D2RN1, MGC-V14W/D2RN1&MGC-V16W/D2RN1
Main control panel
230
29
28
1
27
26 2
3
25
4
8
24 9
23
22 5
6.1
21
6.2
20 7.1
7.2
19 10
18 11
17
12
16
15 14 13
74
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
75
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
IPM
module
1
8
2
7 6 5 4 3
76
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
Filter
board
11
1
10
9 2
8
3
7 6
5 4
1. Power supply port L3
2. Power supply port L2
3. Power input port L1
4. Power input port N
5. Ground wire
6. Loaded power supply port for main control board
7. Power supply port for main control board
8. Power output port L1 after filtering
9. Power output port L2 after filtering
10. Power output port L3 after filtering
11. Ground wire
For 5/7kW
For 10kW
77
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
For 12-16kW
5/7kW
No. Content Note
Show inlet water temperature when the unit is in standby mode and
water pump mode. Display operating frequency when the unit is in
1 Frequency
cooling mode and heating mode. When defrosting displays dF. Pb
displays when anti-freezing mode running.
2 Operating mode 0-Power off,1-water pump,2-cooling,3-heating,4-force cooling
3 Operating fan speed level 0—Power off (1-7)
4 The total required capacity before revised Actual value (Force cooling displays 5)
5 Capacity requirements after revised Actual value (Force cooling displays 5)
6 Temperature set Actual setting temperature under cooling or heating mode
7 T3 Actual value(Outlet temperature of outdoor heat exchanger)
8 T4 Actual value(Outdoor ambient temperature)
9 Tp Actual value(Compressor discharged temperature)
10 Tin Actual value(Water inlet temperature of plate heat exchanger)
11 Tout Actual value(Water outlet temperature of plate heat exchangers)
12 Tb1 Actual value (Temperature 1 of plate heat exchangers)
13 Tb2 Actual value (Temperature 2 of plate heat exchangers(equals to Tb1 )
14 T6 Reserved (Cooling fin surface temperature(reserved)
15 Operation current Actual value
16 Power supply voltage Actual AD value
17 EXV Opening degrees Actual value×8
18 Model 5kW:5; 7kW:7
19 Version number ----
20 Err 1 The last one malfunction code
21 Err 2 The last second malfunction code
22 Err 3 The last third malfunction code
78
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
10-16kW
79
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
5/7kW
Error Note
Content
Code
E9 EEPROM malfunction
H0 Communication malfunction between main chip and IPDU.
E4 T3,T4 sensor malfunction
The same as
E5 Voltage protection malfunction
10-16kW
E6 DC fan motor malfunction
EA A fan in the A region run for more than 5 minutes in heating mode
Eb There are two times E6 fault in 10 minutes (recovery after power off)
HH Inlet water temperature sensor malfunction for 5/7kW models.
EC Outlet water temperature sensor malfunction (5/7kW) 5/7kW
C0 Temperature sensor malfunction of plate heat exchanger for 5/7kW.
P1 High pressure protection
P2 Low pressure protection
P3 Current protection of the compressor
The same as
P4 Discharged temperature protection
10-16kW
P5 T3 high temperature protection of outdoor condenser
P6 IPDU module protection
P8 Typhoon protection
Protection when temperature difference between inlet & outlet water in heating mode is too
CH
large for 5/7kW
Protection when temperature difference between inlet & outlet water in cooling mode is too 5/7kW
CL
large for 5/7kW.
CP Anti-freeze protection of plate heat exchanger for 5/7kW
Pb System anti-freeze protection The same
C8 Water flow switch protection malfunction as 10-16kW
PH Protection when water temperature in heating mode is too high for 5/7kW. 5/7kW
dF Defrosting The same as
d8 Remote control 10-16kW
80
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
10-16kW
81
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
LED displays E9
EEPROM malfunction
NO
Check whether EEPROM is installed properly. Installed properly again.
Yes
LED displays H0
NO
Whether the signal wire is connected normally between module board . Connect wire again.
YES
NO
Replace main PCB.
Judge whether LED on the module board flash normally or not
when powered on.
YES
82
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
NO
YES
Judge whether the wire body is broken and the terminal is fall off. Connect wire again.
NO
YES
Judge whether the port of temperature sensor connected wrong. Connect properly again.
NO
YES
Use a multi-meter to check the resistance value of the temperature sensor Replace temperature sensor.
is normal or not.
NO
LED displays E5
Voltage protection
YES
83
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
LED displays E6
YES
Check the voltage
Check whether the power and voltage of the DC between “+”,”-” port NO Replace PFC
fan motor is normal or not and whether the NO
of PFC module is within module board..
voltage between red and black terminal of DC 277-354V.
motor is from 277V to 354V in waiting state. 是
YES
YES
NO
Check whether the power and voltage of the DC fan
motor is normal or not and whether the voltage between Replace IPM module.
white and black terminal of DC motor is from 15V in
waiting state.
Check voltage
YES between yellow YES
NO and black
Whether the outdoor fan will work after the indoor fan terminal of the Replace fan.
operates for 3 minutes. fan is over 2.4V
YES
NO
84
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
LED displays P1
NO
Judge whether the wiring connection is correct. Connect again.
YES
YES
YES
Check whether pressure of the system is too high. Stop the system.
NO
NO
Rectify the air duct
Whether side air duct of outdoor unit meets the standard.
YES
YES
Whether the heat exchanger needs cleaning. Clean.
NO
YES
Whether the pipeline is blocked. Rectify the pipeline.
NO
YES
Judge the circulation water pump is damaged or not.
Repair or replace the water pump
NO
YES
Whether plate heat exchanger is fouling or blocked severely Clean or replace heat exchanger .
NO
85
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
LED displays P2
NO
Whether wiring connection between low pressure switch and PCB is Connect well again.
connected well or properly.
YES
NO
YES
Short-circuit low pressure switch and check whether the
Replace low pressure switch .
system can work normally.
NO
YES
Check whether the outdoor ambient temperature is too low. Stop the unit.
NO
YES Replace the EXV, then use high
Whether EXV works properly or stuck or blocked pressure nitrogen to clean and air the
pipeline, add the refrigerant at last.
NO
86
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
LED displays P3
NO
Check whether the input current of the power wire is more than 22A.
(31A for 10-16kW ) Replace main PCB
YES
YES
YES
Stop the unit.
Check whether the outdoor ambient temperature is too high.
NO
YES
Check whether the outdoor unit ventilates well. Make the outdoor unit
ventilates well.
NO
` YES
Whether the heat exchanger needs cleaning or not. Clean heat exchanger.
NO
YES Remove the refrigerant pipe and then use high
If the refrigerant pipe is blocked or not? pressure nitrogen or refrigerant to blow the pipe.
NO Vacuumed the pipe then add the refrigerant again.
NO
YES
Whether the circulation water pump is damaged. Repair or replace the water pump
NO
NO
YES
Whether plate heat exchanger is fouling or blocked severely Clean or replace heat exchanger.
NO
87
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
P4: Compressor discharged temperature protection
When the discharged temperature of the compressor is higher than 115°C, the unit will stop running. When the
discharged temperature of the compressor is lower than 83°C , the unit resumes normal operation automatically.
LED displays P4
YES
Check whether the discharged temperature of the compressor is higher than 115°C.
NO
Whether the discharged temperature sensor is damaged or not. Stop leaking and then add the refrigerant again.
NO
Check whether resistance of compressor discharged Replace compressor discharged
temperature sensor is correct or not . temperature sensor.
YES
88
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
LED displays P5
YES
Check whether condenser temperature is higher than 62
degrees
NO
NO
Check whether the resistance of condenser
temperature sensor is correct. Replace the temperature sensor
YES
NO
YES
Clean heat exchanger Whether heat exchanger needs cleaning.
NO
Replace EXV and then use high pressure YES
nitrogen to blow the pipe. Vacuumed the Check if the EXV is blocked or not.
pipe then add the refrigerant again.
NO
89
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
LED displays P6
NO
YES Connect firmly YES
NO again and check
Check if wiring connection NO Connect firmly again and
whether it is Check whether power
between DC filter and IPM module check whether it is
connected wiring is connected
is fasten or not. connected right.
correctly and firmly.
correctly.
NO
YES NO
YES
Replace IPM module and Solve the problem YES
check
whether the system
can operate normally or not..
Check if it is connected NO
normally before entering bridge Connect wire correctly..
NO rectifier . If wire body terminal is
connected firmly.
YES YES
Replace compressor and check Solve the NO
whether the system can Replace the
malfunction.
operate normally or not. Replace the main PCB. same model
fuse.
90
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
LED displays P8
Typhoon protection
Check if strong wind blows outdoor unit or two YES Stop the unit to prevent strong wind
outdoor units blows each other. to blow the outdoor fan.
NO
NO Replace the outdoor main PCB
Check whether the fan motor is damaged.
YES
CH malfunction: Protection when temperature difference between inlet & outlet water in heating
mode is too large for 5/7kW
CL malfunction: Protection when temperature difference between inlet & outlet water in cooling
mode is too large for 5/7kW.
CP malfunction: Anti-freeze protection of plate heat exchanger for 5/7kW.
PH malfunction: Protection when water temperature in heating mode is too high for 5/7kW.
CH malfunction: Protection when water temperature in heating mode is too high for 10-16kW.
PH malfunction: Protection when temperature difference between inlet water & outlet water is too
large for 10-16kW.
① Protection when temperature difference between inlet & outlet water in heating/cooling mode is too large;
② Anti-freeze protection of plate heat exchanger③Protection when water temperature in heating mode is too high
YES
Whether actual measured temperature difference between outdoor outlet water
temperature minus inlet water temperature is higher than 14°C
NO
YES
Check whether the volume of water flow is
Place temperature sensor to the related position or replace it. enough or not.
YES
NO Whether gear of water pump NO
Adjust to high
level is chosen right. Whether water system is stuck.
YES
YES
Water flow pump head of external water pump choices Replace water system component.
91
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
Note: when the ambient temperature is less than 8℃, inlet water temperature and temperature of plate heat exchanger is less
than 2℃, crankcase heater of plate works. CP appears. If inlet water temperature and temperature of plate heat exchanger is
more than 7℃, crankcase heater stops working and CP code disappears.
LED displays CL
To low water temperature protection in heating mode. Determine the location again.
YES
YES
Whether the 4-way valve switch can switch normally Whether the thermometer bulb of water
outlet and inlet location are right.
NO
YES NO
Plug well
Check whether the 4-way valve coil fall off and the valve body jammed.
again Replace main
PCB
NO
NO
Check whether 4-way valve coil and body jammed. Replace main PCB
YES
LED displays Pb
Anti-freeze protection
The actual measured temperature of outdoor water outlet temperature and plate heat YES Normal system
protection
exchanger temperature is less than 3 ℃ in cooling mode. Water inlet temperature and
plate heat exchanger temperature is less than 5 ℃ in heating mode and waiting mode.
NO
YES
Note:
1) The actual measured temperature of outdoor water outlet temperature and plate heat exchanger temperature is less
than 3 ℃ in cooling mode, the compressor stops running. But the water pump continue operating. If the temperature is
more than 8℃, Pb code disappears.
2) The actual measured temperature of outdoor water inlet temperature and plate heat exchanger temperature is less
than 8℃ in waiting state, water pump works. The actual measured temperature of outdoor water inlet temperature and
plate heat exchanger temperature is less than 5℃, the unit enter heating mode in force. Compressor works too. This is
normal.
92
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
YES
Whether system water flow leaks. Repair the leaks and add the water again.
NO
YES
Whether the water pipe is too long and not To configure external water pump
connected to water pump.
NO
YES
Whether water system is stuck. Wash or replace the stuck components and
pipeline.
NO
YES
Whether water pump is damaged. Replace water pump.
NO
YES
Remove the water flow switch and close
the fin manually to check whether Replace water flow switch.
malfunction still exists
YES
93
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
94
MCAC-ATSM-2014-09 Aqua Mini Full DC Inverter Unitary Chiller 50Hz
Appendix
Accessories
Item Name of accessory Qty Shape
Installation and
1 1
operation manual
95
Aqua Mini Full DC Inverter Unitary Chiller 50Hz MCAC-ATSM-2014-09
96