Vous êtes sur la page 1sur 72

SERVICE MANUAL

LCD COLOUR TELEVISION

MODEL LC-22LE420M
In the interests of user-safety(Required by safety regulations in some countries) the set should be
restored to its original condition and only parts identical to those specified should be used.

CONTENTS

CHAPTER 1. SPECIFICATIONS………….….…………………………………………………….1

CHAPTER 2. REMOVING OF MAJOR PARTS…………..……………………………………….3

CHAPTER 3. ADJUSTMENT PROCEDURE……………..……………………………………….7

CHAPTER 4. TROUBLESHOOTING TABLE………...…….……………………………...…….18

CHAPTER 5. MAJOR IC INFORMATIONS……….....….........…………………………...……..35

CHAPTER 6. BLOCK DIAGRAM/ WIRING DIAGRAM……..…….……………………..……..46

CHAPTER 7. PRINTED WIRING DIAGRAM…..…………...……………………………………49

CHAPTER 8. SCHEMATIC DIAGRAM………..………………..………………………...………53

CHAPTER 9. EXPLODED PARTS & PARTS GUIDE ……….……..………………………66

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts
with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for after


sales service only.
The contents are subject to change without notice.
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS
Item Model: LC-22LE420M

LCD screen size 21.5”

Resolution 2,073,600 pixels(1920x1080)

TV-standard PAL: B/G, D/K, I SECAM: B/G, D/K, K/K1 NTSC: M

Receiving VHF/UHF 44.25 — 863.25 MHz


TV
channel CATV S1 — S41ch (including Hyperband)
function
TV-Tuning System Auto Preset 99 ch

STEREO/BILINGUAL NICAM: B/G, I, D/K A2 stereo: B/G

Audio out 3W*2 16ohm


ANT./CABLE UHF/VHF 75 ohm DIN type

HDMI in with HDCP (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz,
INPUT2
1080I/60Hz, 1080P/50Hz, 1080P/60Hz, 1080P/24Hz)

AUDIO in , COMPONENT in (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz,1080I/


Rear INPUT3
50Hz,1080I/60Hz)

OUTPUT VIDEO out, AUDIO out

Terminal INPUT5 PC IN Analog RGB (PC) in (15-pin mini D-sub female connector)
Audio IN PC/HDMI Audio in (Ø 3.5mm jack)
Headphone out Headphone out

HDMI in with HDCP (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz,
INPUT1
Side 1080I/60Hz, 1080P/50Hz, 1080P/60Hz, 1080P/24Hz)

INPUT4 VIDEO in, AUDIO in

USB Photo/Music/Video mode, Software update


English, Portuguese, Russian, Arabian, Persian, Thailand,
OSD language
Indonesian, Vietnamese, French, Chinese(simplified)
Power Requirement AC 110V ~240V / 50/60 Hz
Power Consumption 35W(1W Standby)

TV + stand 5.4kg
Weight
TV only 4.8 kg
Dimension TV + stand 532.8/383.9/187.9mm

(W/H/D) TV only 532.8/350.3/44.2mm

Operating Temperature 0°C — 45°C

[2] DIMENSIONS and VESA wall mount

1
2
CHAPTER 2. Removing of Major Parts
Step 1. Remove the BASE ASSY, after loose 4 screws,

Step 2. Remove AC COVER, after loose 10 screws,

Step 3. Remove BACK COVER, after loose 1 screw,

3
Step 4. Remove LVDS CABLE and SPEAKER, after remove 2 yellow tapes and
disconnect 4 connectors,

Step 5. Remove the base support and 2 top vesa, after loose 8 screws and remove 2
foils.

4
Step 6. Remove KEY ASSY/ IR BD/ IR&KEY CABLE, after loose 3 screws and
disconnect 2 cables.

Step 7. Remove POWER BD and MAIN BD with EMI shielding, after loose 12 screws.

5
Step 8. Get the panel with main chassis away front bezel.

Step 9. Remove MAIN CHASSIS, after loose 4 screws at left and right side.

6
CHAPTER 3. ADJUSTMENT PROCEDURE
[1]ADJUSTMENT PROCEDURE

1. Main Menu (The default value is marked in red)

Layer1 Layer2 Layer3 Layer4 Layer5 Remark


Video AV mode User
Standard When
Location=Home
Dynamic When
Location=Store
Movie
Power Saver
0~100 Only Adaptive
Backlight Backlight is "Off"
Or in VGA
Brightness 0~100
Contrast 0~100
Saturation 0~100
In VGA, this item
Hue -50~50 is hidden
Sharpness -10~10
Adaptive Luma Off
Control
On

Color Color User


Temperature Temperature Cool When AV
Mode=Dynamic
Standard When AV
Mode=Standard
Warm
R Gain 0~255
G Gain 0~255
B Gain 0~255
Advanced Video Adaptive Off VGA except
Backlight On

7
Off
Low
DNR Medium
Strong
Auto
Flesh Tone Off
On
Auto Only enable in
HDMI Mode Graphic HDMI 480p, 576p,
Video 720p, 1080p

VGA Auto Adjust


H.Position 50~50
V.Position -20~20 VGA only
Phase -20~20
Clock -90~90
Audio Balance -50~50(0)
Bass 0~100(50)
Treble 0~100(50)
Surround On/Off
Equalizer Off/Rock/Pop/Live
/Classic
Speaker On/Off
Audio Select Auto/HDMI/PC
HDMI only
Line In
TV Audio Channel Mono/Stereo/Dual
TV only
1/Dual2
Channels Channel Scan Color System Auto/PAL/SECAM
/NTSC
Sound System B/G / I / D/K / M
Channel Scan Scan All
Channels.
Status:Scanning
…/Scan
Complete(Chann
el not found)/Scan
Cancel
Frequency:

8
Analog Channels:
Update Scan Color System Auto/PAL/SECAM
/NTSC
Sound System B/G / I / D/K / M
Channel Scan Scan All
Channels.
Status:Scanning
…/Scan
Complete(Chann
el not found)/Scan
Cancel
Frequency:
Analog Channels:
Analog Manual Search for analog
Scan channels
Start Frequency
(MHz)
End Frequency
(MHz)
Start Search Scan All
Channels.
Status:Scanning
…/Scan
Complete/Scan
Cancel
Frequency:

Analog Channels:
Channel Edit Channel Number:
(Next page is Channel Name:
Channel list) Frequency
Color System Auto/PAL/SECAM
[
/NTSC
Num.
Sound system B/G / I / D/K / M
Type
Finetune Channel Number:
Freq.
Channel Name:
System
Frequency:
Name
Skip On/Off

9
Analog Store
Swap
Are you sure?
Insert
(Confirm dialog)
Delete
]
Clean Channel Are you sure?
OK/Cancel
List (Confirm dialog)
Favorite Channels R
G
Y
B
All data clear Are you sure?
OK/Cancel
(Confirm dialog)
Setup OSD Language English

简体中文
‫اﻟﻌﺮﺑﯿﺔ‬
Français
ไทย
Português
Việt Nam
Bahasa Indonesia
Русский
‫ﻓﺎرﺳﯽ‬
View Mode Normal

Panorama
Available options
Full
depend on input
Zoom
timing.
Underscan
Cinema
Dot by Dot
Time Setup Time Date
Time
Power On Timer Off/On/Once
Timer
Power Off Timer Off/On/Once

10
Timer
Sleep Timer Off
10 Minutes
20 Minutes
30 Minutes
40 Minutes
50 Minutes
60 Minutes
90 Minutes
120 Minutes
Auto Sleep Off
1 Hour
2 Hours
5 Hours
DivX(R)Registrati You must register
on your device to
play DivX
protected videos.
Registration
Code:532J7VZU
DF
Register at
http://vod.divx.co
m
DivX(R) Deregistration You must register
Deregistration code:5DCF8NHI your device to
Deregister at play DivX
http://vod.divx.co protected videos.
m Registration
Continue with Code:532J7VZU
registration? DF
Register at
(OK/Cancel) http://vod.divx.co
m
(OK)

Teletext Decoding Page WEST EUR


Language Arab

11
Farsian
Home
Location
Store
Version Info Model Name:
Version:
Release Date:
Are you sure?
Reset Default OK/Cancel
(Confirm dialog)
Parental Password
Channel Block Analog Block/UnBlock
Input Block TV Block/UnBlock
INPUT1 HDMI1 Block/UnBlock
INPUT2 HDMI2 Block/UnBlock
INPUT3 COMP Block/UnBlock
INPUT4 AV Block/UnBlock
INPUT5 PC IN Block/UnBlock
New Password

Change
Password
Confirm
Password
Are you sure?
Clean All OK/Cancel
(Confirm dialog)

2. Display adjustment

Only adjust HDMI Mode and copy to all of input source


General set-up:
Equipment Requirements: Minolta CA-210 or Equivalent Color analyzer or equivalent instrument.

Input Signal Type:


1. Internal full white pattern.
2. Select Picture mode to Standard mode and check the x, y data.
Input Injection Point: HDMI cable

Alignment method:
Initial Set-up:
1. Select source as “INPUT1 HDMI1”.

12
2. Set Picture mode as “Standard”.
3. Enter factory mode menu: press MENU + Numeric keys “3481” .
Alignment:
1. Press “Menu” key enter factory mode page.
2. Set VideoWhite Pattern to “Medium”.
3. Enter VideoColor Temperature adjust.

Color temperature adjust:


1. Set color temperature to “Cool”
2. Adjust R Gain/G Gain values to meet “Cool” color coordinates.(Keep B Gain set “128”)
3. Adjust R Offset/G Offset values to meet “Cool” color coordinates.(Keep B Offset set “128”)
4. Repeat step 2, 3, 4 twice to meet “Cool” color coordinates specification below.
5. Set color temperature to “Warm”、”Standard” then Repeat 2,3,4 step adjusting.
6. Set color temperature “User” mode then set all values to “128”

Chromaticity Coordinate
Mode
x y
COOL 0.272 ± 0.01 0.277 ± 0.01
STANDARD 0.285 ± 0.01 0.293 ± 0.01
WARM 0.313 ± 0.01 0.323 ± 0.01
Customer Color Panel Native Color Temperature

Check the 16 grayscale pattern should be distinguished and color bar is correct
Reset AV setting in OSD menu, picture mode shall be recalled to be “Standard” mode.

Note:
1. After the main board or LCD panel is replaced, need to perform Display adjustment.
2. Use Minolta CA-210 for color coordinates and luminance check.
3. Before adjusting, all colour analyzers (CA-210) should be coordinates with a same reference TV
set.
4. Luminance > =200 cd/m2 (LC-22LE420M) in the center of the screen when Brightness control at
50, Contrast control at 100, Backlight control at 100.

[2] SERVICE MODE


Enter factory mode menu: press MENU + Numeric keys “3481” to enter factory mode.

13
You can press “RETURN” key to back to normal main menu.
[3] SOFTWARE UPGRADE PROCEDURE
1. Connect to TV USB port to upgrade the software firmware
Please follow the following steps to upgrade the firmware.
I. Turn on TV.
II. Press Menu, select SetupVersion info to check "Version"
III. Copy the correct software firmware (*.pkg) to USB disk.
Ex: Version: VG224G_PA_V2.00, copy VG224G.pkg to USB disk.
IV. Insert the USB disk to TV USB port.

V. TV AC power off -> AC power on


VI. V. TV will upgrade by itself after detect the USB disk condition and the content of the pkg file.
Note: TV's LED will flash during upgrade process
VII. After finish upgrade process, TV will reboot by itself.
VIII. Remove USB disk from TV.
IX. Press Menu, select SetupVersion info.
X. Check the software version is correct or not.

14
[4] Remote control function
Function Testing
Remote control unit

1. POWER
Switch the power on or enters standby mode.
2. 0-9
Set the channel.
TELETEXT mode: Set the page.
3. INPUT
Select a TV input source.
4. SLEEP
Allows you to set a time when the TV automatically switches to standby. This display will disappear after a
few seconds, and the sleep timer automatically starts counting down. If you want to adjust the sleep timer,
you can press SLEEP twice then change the time setting. The sleep timer you can select from Off,
10minutes, 20minutes, 30minutes, 40minutes, 50minutes, 60minutes, 90minutes or 120minutes.
5. AV MODE
Select an adjusted picture setting. (Standard, Dynamic, Movie, Power Saver, User)
6. FREEZE
Set the still image. Press again to return to normal screen.
7. CH▲/▼
Select the channel.
(CH▲) Increase the channel number.
(CH▼) Decrease the channel number.
TELETEXT mode: Select the page.
8. MENU
Display the menu screen.
9. DISPLAY
Display the current channel (or input source) information on the screen.
10. ▲/▼ ◄/► ENTER
Select a desired item on the screen.
11. RETURN
Return to the previous menu screen.
12. R G Y B (Red/Green/Yellow/Blue)
Select 4 preset favorite channels in 4 different categories. While watching, you can toggle the selected
channels by pressing R, G, Y and B.

15
TELETEXT mode: Select a page.
13.
Only for USB using.
Stop
Fast rewind
Fast forward
Pause
Play
14. USB
Direct switch to USB source.
15. (Mute)
Press → Mutes sound.
Press again →Restores sound.
Mute will be canceled if you press VOL+/-.
16. (Flashback)
Press to return to the previous selected channel or external input mode.
17. TV
Direct switch to TV source.
18. PC
Direct switch to PC source.
19. VOL+/-
Set the volume.
(VOL+) Increase the volume.
(VOL-) Decrease the volume.

20. VIEW MODE


Select the Picture Mode.
21. SURROUND
Switch the surround setting. Each time you press SURROUND, the mode changes between On and Off.
You can change the surround setting in Audio menu.
22. MPX
Select the sound multiplex mode.
23. EXIT
Turn off the menu screen.
24. (TELETEXT)
Select the TELETEXT mode. ( all TV image, all TEXT image, TV/TEXT image)
(Reveal hidden for TELETEXT)
TELETEXT mode: Display hidden characters.
(SUBTITLE for TELETEXT)
Turn the subtitles on.
(Hold)
TELETEXT mode: Stop updating Teletext pages automatically. Press again to release the hold
mode.
(Subpage)
Display the Teletext subpage directly when in Teletext mode.
(Top/Bottom/Full)
TELETEXT mode: Set the area of magnification.
[5] Factory Reset
Factory Reset function allows a TV to restore factory settings. Follow below instructions to do Factory Reset.

1. Press MENU + Numeric keys “3481” to enter factory mode, and then the factory mode menu is displayed.

16
2. Press ▲/▼ to select Setup, and then press ► to enter.

3. Press ▲/▼ to select Factory Reset, and then press ► to enter.

4. Press ENTER, then the TV do Factory Reset automatically.

17
CHAPTER 4.TROUBLESHOOTING TABLE
[1]TROUBLE SHOOTING TABLE
The sound is not emitted from the speaker though the picture has come out.

No sound output in all modes?

Yes:

Is the audio signal output of pin (210)


NO
(AOSDATA0), pin (208) (AOBCK), pin Check IC U2101 and its peripheral circuits.
(211) (AOLRCK) and pin (209) (AOMCLK)
of IC U2101 normal?
YES

Is audio signal input to pin (12)


(AOSDATA0), pin (16) (AOBCLK), pin (15) NO
Check the line between IC U2101 and IC
(AOLRCK) and pin (4) (AOMCLK) of IC
U6103
U6103 (AMP) normal?

YES
NO
Is MUTE circuit [PD#] normal? Check the PD#. (Q6103, Q6106, ZD6101, etc.)

YES

Is the audio signal output of pin (3, 4) (L-ch)


NO
and pin (1, 2) (R-ch) of CN6101 Check IC U6101 and its peripheral circuits.

(AOUDIO-CONNECTOR) normal?
YES

Check Speaker Box (right and left) and wire


harness.

18
No sound (during the reception of TV broadcasting)

Does not the sound go out though the picture has come out when UHF/VHF is received?

Is the DIF signal output from pin (10) and pin (11) of TUNER
NO Check the tuner and its peripheral circuits. Replace as required.
(TU1301) normal?

YES
NO
Is the DIF signal sent to pin (184) and pin (185) of IC U2101 Check IC U2101 its peripheral circuits.

normal?

YES
Refer to “No sound output in all modes”.

19
No sound from external input devices (YPbPr)

Does not the sound of the audio signal input to (YPbPr) go out?

Is the audio signal properly sent to pin (8) and pin (10) of
NO Check the connection to CN1105 and the external input device.
CN1203 ?

YES
NO
Is the audio signal properly sent to pin (3) Check the line between CN1105 and IC U6203

(IN2a) and pin (7) (IN2b) of IC U6203?

YES

NO
Is the audio signal properly sent to pin (196)
(AIN0_L) and pin (194) (AIN3_R) of IC Check the line between U6203 and IC U2101

U2101?

YES

Refer to “No sound output in all modes”.

20
No
Nosound
soundfrom
fromexternal
externalinput
input
devices
devices
(VGA)
(3)

Doesnotnot
Does the the sound
sound of the
of the audio audio
signal inputsignal input
to VGA go out? to input7 (Composite) go out?

MAIN UNIT:
Is the audio signal properly sent to pin (3)
(4) and pin (2) of NO Check the connection to CN4104
CN1104 and the external input device.
CN1104?
CN4104?

YES YE
NO
Is the audio signal properly sent to pin (1) Check the line between CN4104
CN1104 and IC U6203.
U2101.

(IN1a) and pin (6) (IN1b) of IC U6203?

YES
NO
Is the audio signal properly sent to pin (196)
Check the line between U6203 and IC U2101
(AIN0_L) and pin (194) (AIN0_R) of IC
U2101?

YES

Refer to “No sound output in all modes”.

21
No sound from external input devices input4 (AV INPUT)

Does not the sound of the audio signal input to (AV input) go out?

Is the audio signal properly sent to pin (3) and pin (6) of
NO Check the connection to CN1201 and the external input device.
CN1201 ?

YES
NO
Is the audio signal properly sent to pin (3) Check the line between CN1201 and IC U6203

(IN2a) and pin (7) (IN2b) of IC U6203?

YES

NO
Is the audio signal properly sent to pin (196)
(AIN0_L) and pin (194) (AIN3_R) of IC Check the line between U6203 and IC U2101

U2101?

YES

Refer to “No sound output in all modes”.

22
No sound from external input devices (USB)

Does not the sound of the audio signal input to USB go out?

YES
NO
Is USB stick audio format correct? Change to correct mp3 format

YES
NO
Is the USB +5V Q7104 sent to pin (1) of CN1103? Check the connection to Q7104 and the external input device.

YES
Is the USB con (CN1103) signal properly sent to pin (109) NO Check the line between CN1103 and IC 2101
(USB_DM) and pin (110) (USB DP) of IC U2101?

YES
Refer to “No sound output in all modes”.

23
The audio signal is not output(headphone)

No audio signal output from Headphone terminal (CN6202).

No
Is audio signal output properly from pin (12) (OUT_L) and pin Check the connection to CN6202 and external devices.

(3) (OUT_R) of IC U6201 to Jack (CN6202)?

YES

Is the audio signal output properly from IC U2101 pin (201)


No
Check the line between IC U2101 and IC U6202.
(AL1O) and pin (203) (AR1O) to pin (13) (INL) and pin (6) (INR)

of IC U6201

YES
Check IC2101 and its peripheral circuits.

24
The audio signal is not output(AV out)

No audio signal output from AV out terminal (CN1202).

Is audio signal output properly from pin (12) (OUT_L) and pin
No
Check the connection to CN1202 and external devices.
(3) (OUT_R) of IC U6201 to Jack (CN1202)?

YES
Is the audio signal output properly from IC U2101 pin (200)
No
(AL0) and pin (202) (AR0) sent to U6201 pin(2) (INR) and
Check the line between IC U2101 and U6201
pin(13) (INL)?

YES

Check IC U2101 and its peripheral circuits.

25
No picture on the display (1)

The picture doesn't appear in all modes.

Main UNIT:
Is LVDS signal output IC U2101 in each mode?

(O0N/O0p),(O1N/O1P),(O2N/O2P),(O3N/O3P),(OCKN/OCKP), (E0N/E0p), (E1N/E1P), (E2N/E2P), (E3N/E3P), (ECKN/ECKP)

NO

YES Check IC U2101 and its peripheral control circuits.

NO
Is the above-mentioned LVDS signals output to Check the line between IC U2101 and CN4101

connector CN4101 ?

YES
Control signals Backlight_ON , PSON, and it peels off
NO
YES
Is LCD controller's control signal normal? and whether normality is checked.

YES

Similarly, is the LVDS signal input to connector of the


NO
Wire harness is checked.
panel module?

YES

Check the panel module.

26
No picture on the display (TV)

Does not the picture come out when VHF/UHF is received?

Main UNIT:
Is the voltage of regulation for a TUNER circuit and the power Each power supply circuit is checked.
NO
supply terminal of IC U2101 supplied?

YES
Is the DIF signal output from pin (10) and pin (11) of TUNER Check the tuner and its peripheral circuits. Replace
NO
(TU1301)? as required.

YES
Is the DIF signal sent to pin (184) and pin (185) of IC U2101?
NO Check IC U2101 its peripheral circuits.

YES
Refer to “The picture doesn't appear in all modes.”

27
<External input Input4>No picture on the display (AV)

Does not the picture of the AV video signal input to Input4(AV)?

YES
Terminal
Check the setting of an external input device that
Is AV signal sent to pin (2) of AV (CN1201) ?
NO
connects of CN1201

Main UNIT: YES


Is AV signal sent to pin (181) of IC U2101?
NO Check the line between IC U2101 and CN1201.

YES
Refer to “The picture doesn't appear in all

modes.”?

28
<External input Input1(Side HDMI1)>No picture on the display

Does not the picture of the HDMI signal input to Input1 (HDMI1)?

Terminal
Is the HOT_PLUG detection function of pin (19) of
NO Check the line between pin (16) of IC U8103 and

a HDMI terminal (CN8102) normal? CN8102.

YES
Check the connection and setup with the
Main UNIT:
Is TMDS signal input into pin external HDMI devices.

(33, 32) RX1_2/ RX1_2B,

(30,29 )RX1_1 /RX1_1B,


NO Check the line between IC U8103 and CN8102.
(28,27)/RX1_0/RX1_0B

(24, 25)/RX1_C/RX1_CB of IC U1205?

YES
Refer to “The picture doesn't appear in all

modes.”?

29
<External input Input2 (Rear_HDMI)>No picture on the display

Does not the picture of the HDMI signal input to Input2 (HDMI)?

Terminal
Is the HOT_PLUG detection function of pin (19) of
NO Check the line between pin (1) of IC U8103 and

a HDMI terminal (CN8103) normal? CN8103.

YES
Check the connection and setup with the

Is TMDS signal input into pin external HDMI devices.

(12 .11) RX3_2/ RX3_2B,

(10,9 ) RX3_1 / RX3_1B,


NO Check the line between IC U8103 and CN8103.
(8,7) RX3_0/ RX3_0B

(6, 5) RX3_C/ RX3_CB of IC U1205?

YES
Refer to “The picture doesn't appear in all

modes.”?

30
<External input USB>No picture on the display

Does not the sound of the video signal input to USB go out?

Change to correct . JPG/MP3/MPEG-2 format.


Is USB stick video format correct?
NO

YES
Check the CN1103 and the external input device.
Is the USB +5V sent to pin (1) of CN1103?
NO

YES
Is the USB con (CN1103) signal properly sent to
NO Check the line between CN1103 and IC U2101.
pin (109) (USB_DM) and pin (110) (USB_DP) of IC

U2101?

YES
Refer to “The picture doesn't appear in all modes.”

31
<External input Input3(Component)>No picture on the display

Does not the picture of the component video signal input to Component?

Terminal
Is Component Y/Pb/Pr signal sent to pin (2)/Y,
NO Check the setting of an external input device that

(4)/Pb, (6)/Pr of CN1203 ? connects of CN1203

Main UNIT: YES


Is Component Y/Pb/Pr signal sent to pin (163)/Y,
NO Check the line between IC U2101 and CN1203.

(165)/Pb, (166)/Pr of IC U2101?

YES

Refer to “The picture doesn't appear in all modes.”

32
<External input input5>No picture on the display

Does not the picture of the VGA signal input to D-SUB go out?

Set the timing which TV is support


Is Video format correct?
NO

YES
Terminal
Is R/G/B/H/V signal sent to pin (1)/R, (2)/G, (3)/B, Check the setting of an external input device that
NO
(14)/H, (13)/V of VGA (CN1102)? connects of CN1102

YES
Main UNIT:
Is R/G/B/H/V signal sent to pin (156)/R, (154)/G,
NO Check the line between IC U2101 and CN1102.
(152)/B, (150)/H, (149)/V of IC U2101?

YES
Refer to “The picture doesn't appear in all modes.”

33
34
CHAPTER 5. MAJOR IC INFORMATIONS
[1]MAJOR IC INFORMATIONS
1.1. U2101 (MT5301B)
GENERAL DESCRI PTION
The MediaTek MT5301B family is a backend decoder and a TV controller and offers high
integration for advanced applications. It combines a high definition video decoder, an
audio
decoder, a dual-link LVDS/mini-LVDS transmitter, and an NTSC/PAL/SECAM TV
decoder with a 3D comb filter (NTSC/PAL). The MT5301B enables consumer electronics
manufactures to build high quality, low cost and feature-rich DTV.
World-Leading Audio/Video Technology: The MT5301B supports Full-HD
MPEG1/2/4/DiviX/VC1/RM/H.264/AVS video decoder standards, and JPEG. The
MT5301B also supports MediaTek MDDiTM de-interlace solution can reach very smooth
picture quality for motions. A 3D comb filter added to the TV decoder recovers great
details for still pictures. The special color processing technology provides natural, deep
colors and true studio quality video.Also, the MT5301B family has built-in high resolution
and high-quality audio codec.
Rich Features for High Value Products: The MT5301B family enables true single-chip
experience. It integrates high-quality HDMI1.3 (partial HDMI1.4), high speed VGA ADC,
dualchannel LVDS, USB2.0 receiver, , TCON and panel overdrive.
Key Features:
1. Worldwide multi-standard analog TV demodulator
2. A muti-standard video decoder
3. An audio decoder
4. HDMI1.3 receiver (cover HDMI1.4 partial Spec)
HDMI 1.4 Ethernet 3D over 4Kx2K Audio Additional
Spec. Channel HDMI Return Color Space
Channel
Optional Yes No Yes Yes
5. Audio codec
6. TCON
7. Panel overdrive control
8. Local dimming

GENERAL FEATURE LIST


Host CPU
ARM1176JZS
14K Boot ROM

35
JTAG ICE interface
Watch Dog timers

Transport Demultiplexer
Support DES / 3-DES / DVB / AES / de-scramblers
Up to 8 even/odd keys for descrambling
Supports 32 PID filters and 32 section filters
Supports 32 PID filters for recording
Supports hardware CRC-32 check
Supports PCR recovery function
Supports a micro-processor for stream process and video start code detection

MPEG2 Decoder
MPEG MP@ML, MP@HL
Supports de-blocking filter

MPEG1 Decoder
MPEG4 Decoder
ASP@L5

H.264 (MPEG4.10) HD Decoder (AVC)


MP@L4.0, HP@L4.0, constrained BP@L3 video standard

VC-1 (SMPTE421M)
MP@HL, AP@L3(Partial Support, support up to 1920x1080)
WMV9 decoder MP@HL

DivX (XviD) Decoder


DIVX3 / DIVX4 / DIVX5 / DIVX6 / DIVX HD
AVS Decoder
Jizhun profile @Level 6.0.1
RMVB Decoder
RealVideo8/9/10
Soreson H.263
Still Image decoding
JPEG (base-line or progressive)

De-mosquito engine
2D/3D for all AV inputs

2D Graphics
Supports multiple color modes
Point, horizontal/vertical line primitive drawings
Rectangle fill and gradient fill functions
Bitblt with transparent options
Alpha blending and optional pre-multiplied alpha composition Bitblt

36
Stretch Bitblt
YCbCr to RGB color space conversion
Support index to direct mode bitblt

Image Resizer
Supports 16bpp/32bpp direct color format.
Supports 420/422 video format.
Supports 420/422/444 JPEG format.
Arbitrary ratio vertical/horizontal scaling of video, from 1/128X to 128X
Simple DMA.

OSD Plane
Three linking list OSDs with multiple color mode and two of them has up-scaler

Video Plane
Supports video freeze and over scan.
Flesh tone management
Gamma correction
Color Transient Improvement (CTI)
2D Peaking
Saturation/hue adjustment
Brightness and contrast adjustment
Black and White level extender
Adaptive Luma management
Automatic detect video, film and mixed-mode source
3:2/2:2 pull down source detection
Supports FHD motion-adaptive de-interlace in 32bit dram interface
Supports excellent low angle image processing
Brilliant boundary shaping for moving object
Advanced non-linear panorama scaling.
Programmable zoom viewer
Progressive scan output
Supports alpha blending for OSD on video plane.
Dithering processing for flat panel display
Frame rate conversion.
Supports FHD panel and VGA dot-to-dot
Supports PIP/POP, (dual de-interlace, one HD and one SD)

OD
Support 60Hz Full-HD and WXGA panel over drive.

TCON
Flexible timing control with programmable timing

37
i. Horizontal timing control
ii. Vertical timing control
iii. Multi-line timing control
iv. Multi-frame timing control
Support gate power modulation timing
Support 1/2/4/8 frame inversion, 1-line inversion, 2-line inversion, and could up to 255-line dot inversion

Local Dimming
Block division: up to 800 total blocks, up to 100 horizontal blocks
Support 50K ~ 50M SPI clock rate

LVDS
Support 6/8/10/12-bit one-link, or 6/8/10-bit dual-link LVDS transmitter,
Built-in spread spectrum for EMI performance
Programmable panel timing output

Mini-LVDS
Single port 6/8-bit 6 pairs mini-LVDS output for WXGA 60Hz panel
Single port 6/8-bit 3 pairs mini-LVDS output for WXGA 60Hz panel
Dual port 6/8-bit 3 pairs mini-LVDS output for WXGA 60Hz panel
Single port 8bit 6 pairs mini-LVDS output for FHD 60Hz panel
Dual port 8 bit 6 pair mini-LVDS output for FHD 60Hz panel
Dual port 8bit 3 pairs mini-LVDS output for FHD 60Hz panel

CVBS In
On-chip 54 MHz 10-bit video ADC
Supports PAL (B,G,D,H,M,N,I,Nc), NTSC, NTSC-4.43, SECAM
NTSC/PAL supports 3D/2D comb filter
Built-in motion-adaptive 3D Noise Reduction
VBI data slicer for CC/TT decoding
Supports 2 S-Video.
MT5301B support 2-channel CVBS.
Supports SCART connector

VGA In
Supports VGA input up to UXGA 162 MHz
Supports full VESA standards

Component Video In
Supports two component video inputs
Supports 480i / 480p / 576i / 576p / 720p / 1080i / 1080p

Audio ADC
MT5301B support 1-pair L/R input

Audio digital input

38
MT5301B support 2 bit (4 channel) I2S audio input (muxed with GPIO).

HDMI Receiver
One channel HDMI1.4
v. Maximum data rate can be up to 3.3 GHz
vi. Support 3D video format
vii. Audio Return channel
EIA/CEA-861B
CEC

Video bypass
TV bypass
CVBS Monitor (any AV input)

TV audio demodulator
Supports BTSC / EIA-J / A2 / NICAM / PAL FM / SECAM world-wide formats
Standard automatic detection
Stereo demodulation, SAP demodulation
Mode selection (Main/SAP/Stereo)

Audio DAC
MT5301B support 2-pair audio DACs

DRAM Controller
16bit DDR2/DDR3 interface,
MT5301B Support DDR2 1026 MHz, DDR3 1188MHz.
Supports 512Mb or 1 Gb DDR2 DRAM device and 1Gb or 2Gb DDR3 device. MT5301B has 16-bit data
bus offers
up to 256MB space (one x16 DRAM device).
Supports DDR2-800/DDR2-1066/DDR3-1333/DDR3-1600 device

Audio DSP
MPEG-1 layer I/II decoding
Support WMA / HE-AAC
Audio output: 5.1ch + 2ch (down mix) + 2ch(bypass)
Pink noise and white noise generator
Equalizer
Bass management
3D surround processing with virtual surround
Audio and video lip synchronization
Supports bass/treble
Automatic volume control
MT5301B support 2-bit (4-channel) main audio I2S output interface: each of these channels is up to 24-bit
resolution.

39
S/PDIF interface
Support SPDIF in bypass
One SPDIF out

Analog TV IF Demodulator
Supports world-wide analog TV standard
Accept Low IF frequency
Full digital AGC control and carrier recovery
Embedded SAW filter and IF Amplifier. Cost effective TV front-end structure and no more costs on
viii. External analog SAW filters (Video/Audio)
ix. External analog IF demodulator
x. Extra peripheral circuit on CVBS signal data path
xi. External SAW filter and IF VGA on tuner

Peripherals
MT5301B support two built-in UARTs with Tx and Rx FIFO.(one is muxed with GPIO).
Seven basic serial interfaces; one is for the tuner, one is the master for general purpose, and one is the
slave for
VGA DDC, the other four extra slave serial interfaces used for HDMI EDID data (three are muxed with GPIO).
MT5301B support two PWMs (one is muxed with GPIO).
IR receiver
Real-time clock and watchdog controller
Built-in 2-link USB2.0/1.1, USB port0 supports external hub,
Built-in uP for standby mode
Support SDIO interface pin muxed
Supports two serial flash or one serial
MT5301B support five-input low-speed ADC.
Supports boundary scan (JTAG)

IC Outline
MT5301B is 256-pin LQFP package with EPAD
3.3V/1.12V/1.2V and 1.8V for DDR2 or 1.5V for DDR3

1.2. U3103 (W971GG6JB-25 1G WBGA-84)


Description
The W971GG6JB is a 1G bits DDR2 SDRAM, organized as 8,388,608 words 8 banks 16 bits.
This
device achieves high speed transfer rates up to 1066Mb/sec/pin (DDR2-1066) for general
applications. W971GG6JB is sorted into the following speed grades: -18, -25 and -3. The -18 is
compliant to the DDR2-1066/CL7 specification, the -25 is compliant to the DDR2-800/CL6
specification, the -3 is compliant to the DDR2-667/CL5 specification.

40
All of the control and address inputs are synchronized with a pair of externally supplied differential
clocks. Inputs are latched at the cross point of differential clocks (CLK rising and CLK falling). All
I/Os are synchronized with a single ended DQS or differential DQS- DQS pair in a source
synchronous fashion.
Features
_ Power Supply: VDD, VDDQ = 1.8 V
± 0.1 V

_ Double Data Rate architecture: two data transfers per clock cycle
_ CAS Latency: 3, 4, 5, 6 and 7
_ Burst Length: 4 and 8

_ Bi-directional, differential data strobes (DQS andDQS ) are transmitted / received with data
_ Edge-aligned with Read data and center-aligned with Write data
_ DLL aligns DQ and DQS transitions with clock
_ Differential clock inputs (CLK and CLK )
_ Data masks (DM) for write data
_ Commands entered on each positive CLK edge, data and data mask are referenced to both
edges of DQS
_ Posted CAS programmable additive latency supported to make command and data bus efficiency
_ Read Latency = Additive Latency plus CAS Latency (RL = AL + CL)
_ Off-Chip-Driver impedance adjustment (OCD) and On-Die-Termination (ODT) for better signal
quality
_ Auto-precharge operation for read and write bursts
_ Auto Refresh and Self Refresh modes
_ Precharged Power Down and Active Power Down
_ Write Data Mask
_ Write Latency = Read Latency - 1 (WL = RL - 1)
_ Interface: SSTL_18
_ Packaged in WBGA 84 Ball (8X12.5 mm2), using Lead free materials with RoHS compliant
1.3. U6101 (AD82581-LE48NAY LQFP48)
Description
AD82581 is a digital audio amplifier capable of driving a pair of 8Ω,10W or a single 4Ω,20W
speaker, both which operate at a 24V supply without external heat-sink or fan requirement.
Using I2C digital control interface, the user can control AD82581’s input format selection, mute
and volume control functions. AD82581 has many built-in protection circuits to safeguard AD82581
from connection errors.
Features
16/18/20/24-bit input with I2S, Left-alignment
and Right-alignment data format

41
PSNR & DR (A-weighting)
Loudspeaker: 97dB (PSNR), 105dB (DR) @24V
Multiple sampling frequencies (Fs)
32kHz / 44.1kHz / 48kHz and
64kHz / 88.2kHz / 96kHz and
128kHz/176.4kHz/192kHz
System clock = 64x, 128x, 256x, 384x, 512x, 768x,
1024x Fs
256x~1024x Fs for 32kHz / 44.1kHz / 48kHz
128x~512x Fs for 64kHz / 88.2kHz / 96kHz
64x~256x Fs for 128kHz/176.4kHz/192kHz
Supply voltage
3.3V for digital circuit
12V~24V for loudspeaker driver
Loudspeaker output power for 24V
10W x 2CH into 8Ω @0.27% THD+N for stereo
12W x 2CH into 8Ω @0.3% THD+N for stereo
15W x 1CH into 4Ω @0.2% THD+N for mono
20W x 1CH into 4Ω @0.25% THD+N for mono
Anti-pop design
Over-temperature protection
Internal PLL
Under-voltage shutdown
Over-current protection
Applications
· CD and DVD
· TV audio
· Car audio
· Boom-box
· MP3 docking systems
· Powered speaker
· Wireless audio
· USB speaker
1.4. U8103(IT6633)
Features
The IT6633 is a three-to-one HDMI v.1.3 active switch that supports a signalling
rate of up to 2.25Gbps and the new Deep Color modes. A one-port SINK systems
such as flat-panel TVs or LCD projectors could also easily upgrade to three-port by

42
adding an IT6633 at the front. The IT6633 operates in software mode that allows the
system to control it via a two-line serial interface, PCSCL/PCSDA. The IT6633 offers
two selectable serial programming addresses by PCADR0.
As a active switch, the IT6633 equalizes incoming TMDS data with optimal quality
regardless of the incoming signal quality. The highly acclaimed equalization
technology of ITE TECH. INC. provides for support of long or low-quality HDMI cables
at even the highest speeds. Input terminations of theTMDS inputs and output current
levels are both programmable. In addition, the input terminations are disconnectable
and hence significantly lower the system power consumption in inactive modes.
The IT6633 embeds an EDID RAM to save the cost of the Three external EDID
ROMs. The process of downloading the EDID data into the RAM is simplified by the
automatic read-back capability of the
IT6633, minimizing the need of MCU intervention. The IT6633 also embeds three
1K-ohm resisters for HPD signal paths to save external resisters and easy to
implement the plug authentication.
The IT6633 also incorporates I2C repeater in its DDC switches, which isolates the
DDC capacitances of the two sides of the switch. This allows for longer cable
cascading as well as significantly eases the system design to pass Test ID 8-9:
DDC/CEC Line Capacitance and Voltage of the HDMI Compliance Test.
The IT6633 also distinguish itself from its peers in that it offers 8kV of Human
Body Mode ESD protection to all TMDS high-speed input pins. This saves significant
costs in external high-speed ESD diodes, which could be very expensive .
Features
 HDMI active switch, providing superior performance over traditional passive
switches
 Compliant with HDMI 1.3 and DVI 1.0 standards
 Serial data rate at up to 2.25Gbps, capable of supporting the following digital
video formats in Deep Color Mode at up to 36 bits (12 bits/color):
 DTV resolutions: 480i, 576i, 480p, 576p, 720p, 1080i to 1080p
 PC resolutions: VGA, SVGA, XGA, SXGA to UXGA
 Single 3.3V operation
 Internal AC-coupling at TMDS inputs to cope with uneven intra-pair DC levels of
incoming TMDS signals.
 Embedded EDID RAM saves external EDID ROM costs
 Embedded HDP resistors
 Integrated HPD switches
 Active port detection by monitoring PWR5V inputs and TMDS input clock.
 DDC I2C repeater isolates backend DDC capacitive loading from frontend,

43
enhancing the DDC operation compatibility
 Human Body Mode ESD protection up to 8kV for all TMDS differential input pins
 Disconnectable input terminations with auto-calibrated impedances
 Adaptive input equalization supporting long and short cables at the same time
 Software-mode operation providing flexibility
 Two possible serial programming device address..
 Programmable TMDS output current level
 Programmable source terminations compliant with HDMI 1.3 standard, providing
optimal source
 data eyes at high speeds
 High-impedance TMDS output when disabled
 Optional backend receiver termination detection for auto powerdown
 64-Pin LQFP package
 RoHS Compliant ( 100% Green available )
1.5. U6202 (DRV632)
DESCRIPTION
The DRV632 is a 2-VRMS pop-free stereo line driver designed to allow the removal of the output
dc-blocking capacitors for reduced component count and cost. The device is ideal for single-supply
electronics where size and cost are critical design parameters
Designed using TI’s patented DirectPath™ technology, The DRV632 is capable of driving 2
VRMS into a 10-kΩ load with 3.3-V supply voltage. The device has differential inputs and uses
external gain-setting resistors to support a gain range of ±1 V/V to ±10 V/V, and gain can be
configured individually for each channel. Line outputs have ±8-kV IEC ESD protection, requiring
just a simple resistor-capacitor ESD protection circuit.The DRV632 has built-in active-mute control
for pop-free audio on/off control.The DRV632 has an external undervoltage detector that mutes the
output when the power supply is removed, ensuring a pop-free shutdown.
Using the DRV632 in audio products can reduce component count considerably compared to
traditional methods of generating a 2-VRMS output. The DRV632 does not require a power supply
greater than 3.3 V to generate its 5.6-Vpp output, nor does it require a split-rail power supply. The
DRV632 integrates its own charge pump to generate a negative supply rail that provides a clean,
pop-free ground-biased 2-VRMS output.
The DRV632 is available in a 14-pin TSSOP.
FEATURES DESCRIPTION
• Stereo DirectPath™ Audio Line Driver– 2 Vrms Into 10 kΩ With 3.3-V Supply• Low THD+N
23

< 0.01% at 2 Vrms Into 10 kΩ• High SNR, >90 dB• 600-Ω Output Load Compliant
• Adjustable Gain by External Gain-Setting Resistors• Low DC Offset, <1 mV•
Ground-Referenced Outputs Eliminate
DC-Blocking Capacitors

44
– Reduce Board Area
– Reduce Component Cost
– Improve THD+N Performance a– No Degradation of Low-Frequency Response Due to
Output Capacitors• Short-Circuit Protection
• Click- and Pop-Reduction Circuitry
• External Undervoltage Mute
• Active Mute Control for Pop-Free Audio On/Off Control• Space-Saving TSSOP Package
APPLICATIONS• Set-Top Boxes
• Blu-ray Disc™, DVD Players
• LCD and PDP TV
• Mini/Micro Combo Systems
• Sound Cards
• Laptops

45
CHAPTER 6.BLOCK DIAGRAM/WIRING DIAGRAM
[1]BLOCK DIAGRAM(21.5”)

[2]POWER MANAGEMENT BLOCK DIAGRAM


There are 1 part circuits in Power board of this project (fig.1), Power circuits which is a single
layer board, There are 3 output in the power parts, one is interface board including USB and TV
tuner et; the other is inverter board and audio circuit.+24V output is inverter & audio part.the
system block diagram as below; the last is panel Vcc, the power is 12V.

46
LC-22LE420M

[3]WIRING DIAGRAM
(LC-22LE420M)

47
48
CHAPTER 7.PRINTED WIRING DIAGRAM
[1]MAIN UNIT PRINTED WIRING BOARD (LC-22LE420M)
TOP

49
BOTTOM

50
[2]POWER SCHEMATIC DIAGRAM- POWER BOARD WITH TOP/BOTTOM VIEW
TOP Layer(LC-22LE420M)

51
Bottom Layer (LC-22LE420M)

[3]KEY UNIT PRINTED WIRING BOARD(LC-22LE420M)

[4] IR UNIT PRINTED WIRING BOARD (LC-22LE420M)

52
CHAPTER 8.SCHEMATIC DIAGRAM
[1]MAIN SCHEMATIC DIAGRAM (LC-22LE420M)
01 MAIN POWER

53
02 MT5301B

54
03 Peripheral/ Flash.

55
04 DDR SDRAM

56
05 LVDS

57
06 AUDIO AMP

58
07 HP/ Lineout/ Audio SW

59
08 HDMI Interface

60
09 VGA/ USB/ RS232

61
10 YCbCr/ CVBS/ SPDIF

62
11 TUNER

[2]POWER SCHEMATIC DIAGRAM


POWER SCHEMATIC DIAGRAM FOR(LC-22LE420M)

1. 1) AC Input and EMI Filter:(fig.3)

(fig.3)

63
CN801 is a connector for connecting AC Power. F850&F851 is fuse to protect all the circuit AC.
Input voltage is from 90V to 264V. CY801, CY802, CY803 are used high frequency noise of
primary between common GND. one inputting main circuit to prevent man from shock. L801, C851,
is used to filter low frequency noise. R850, R851 are used to discharge .

2) MAIN POWER Control Circuit:(fig.4)

64
fig.4
U830 is a current-mode PWM controller with excellent power-saving operation, It features a
high-voltage current source to directly supply the startup current from bulk capacitor and further to
provide lossless startup circuit. Max start-up current for U830 is 100uA, When current flow from the
bulk capacitorC853/C854 through R832 and R833 gets to HV pin to start up U830,
Meanwhile, the VCC supply current is as low as 1mA thus most of the HV current is utilized to
change the VCC capacitor C856, the Vcc supply current is provided from the auxiliary winding of
the transformer PIN4.
INN801 detects the MOSFET current, from the CS in.When CS pin over 0.7V, theU830 will
enter auto-recovery type protection, Presenting a hiccup mode. The gate-out will not resume
switching until OCP falls below 0.85V.
U830 control 5V&16V output ,D856,C862,C8663,L855 are used to 5V rectifier and smooth ,for
system standby function circuit .D861,C864,C863 are sued rectifier to U930 Vcc input Pin,
and 16Voutput through U930 rectifier to interface board.

65
9. EXPLODED PARTS

No. PARTS CODE DESCRIPTION EXPLODED PARTS

LC-22LE420M

1 9KD102222530H LCP21.5"M215HGE-L10,ML5HE10901(A)(CMO)HF

2 9KD03G224G01R ASSY FRONT BEZEL,VG224G

3 9KD05G224G01R ASSY BACK COVER FOR ASEAN,VG224G

4 9KD04T264C01R ASSY KEY,VT264C

5 9KD02T264C01R ASSY BASE,VT264C

6 9KD05G224G05R ASSY IF SHIELDING FOR ASEAN,VG224G

7 9KD1X1500500R PCBA,KP/BD,VG264C-52SP RoHS

66
8 9KD0T1600500R PCBA,IR/BD,VG264C-52SP,ROHS

9 9KD471200500R PCBA,IF/BD,VG224G-51SP,ROHS

10 9KDAC1400500R PCBA,PI/BD,VG224G-51SP,ROHS

11 9KD20T464D02R AC COVER ,VT464D

12 9KD151040100R Remote controller RC-QSHAR-520

PWRCORD 2.5A/250V BLK 1.6/0.08M CEE


9KD0709000B0R
(India/ Indonesia/ Central Asia/ Malaysia)
PWRCORD 2.5A/250V BLK 1.6/0.2M ASTA 2P TO
13 9KD0709000A0R
(Singapore/Middle East)
PWRCORD 2.5A/250V BLK 1.6/0.2M CCC 2P TO
9KD070900090R
(Philippines)

14 9KD100300019R SPEAKER 3W16Ω 395/415mm R/B/W W/CASE

67
15 9KD3006009V0R HRN ASSY 6P 135MM UL1061#30

16 9KD3030046A0R HRN ASSY LVDS 2X15P TO 30P 95mm W/LOCK

17 9KD301400820R HRN ASSY 2X7P TO 6P/4P 440/520mm

18 9KD08T264C02R TOP VESA HOLDER,VT264C

19 9KD02T264C04R BASE SUPPORT,VT264C

20 9KD000001000R BOLT,#4-40x12.5,Ni ROHS

21 9KD05G224G02R ASSY MAIN CHASSIS ASEAN-L10,VG224G

22 9KD476640900R SCREW,B,CROSS,W/W-SPR,M4*42,Zn,ROHS

68
23 9KD10T421J01R WIRE CLIP,CH-01S-V0,VT421J

24 9KD10T321H02R WIRE CLIP,CHR-05-V0,VT321H

25 9KD799001010R ADAPTER RF JACK/ PAL PLUG (Philippines)

26 9KD416606901R SCREW,B,CROSS,M4*6,Zn-black

27 9KD146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc

28 9KD112322100R SCREW,P,CROSS,T.T-M3*4.5,Zn,ROHS

29 9KD018303900R SCREW,I,CROSS,M3*3,Zn-BLK,ROHS

30 9KD112310500R SCREW,P,CROSS,T.T-3*10,BLK-Zn

69
31 9KD016306900R SCREW,I,CROSS,Φ5.5,T3*6,BLK-Zn

32 9KD412608500R SCREW,B,CROSS,T.T-4*8,BLK ROHS

33 9KD212612120R SCREW,B,CROSS,T.T-4*12,BLK ROHS

34 9KD146304200R SCREW,P,CROSS,W/WAS,M3*4,Zn-Cc,ROHS

70
9. PARTS GUIDE
PRICE NEW Part
No. PARTS CODE DESCRIPTION
RANK MARK Delivery
LC-22LE420M
1 9KD102222530H CB N * LCP21.5"M215HGE-L10,ML5HE10901(A)(CMO)HF
2 9KD03G224G01R AY N * ASSY FRONT BEZEL,VG224G.
3 9KD05G224G01R BC N * ASSY BACK COVER FOR ASEAN,VG224G.
4 9KD04T264C01R AN N * ASSY KEY,VT264C.
5 9KD02T264C01R BA N * ASSY BASE,VT264C.
6 9KD05G224G05R AP N * ASSY IF SHIELDING FOR ASEAN,VG224G.
7 9KD1X1500500R AP N * PCBA,KP/BD,VG264C-52SP RoHS.
8 9KD0T1600500R AK N * PCBA,IR/BD,VG264C-52SP,ROHS.
9 9KD471200500R BR N * PCBA,IF/BD,VG224G-51SP,ROHS.
10 9KDAC1400500R BF N * PCBA,PI/BD,VG224G-51SP,ROHS.
11 9KD20T464D02R AG N * AC COVER ,VT464D.
12 9KD151040100R AT N * Remote controller RC-QSHAR-520
9KD0709000B0R AR N * PWRCORD 2.5A/250V BLK 1.6/0.08M CEE (India/ Indonesia/ Central Asia/ Malaysia)
13 9KD0709000A0R AT N * PWRCORD 2.5A/250V BLK 1.6/0.2M ASTA 2P TO (Singapore/Middle East)
9KD070900090R AR N * PWRCORD 2.5A/250V BLK 1.6/0.2M CCC 2P TO (Philippines)
14 9KD100300019R AZ N * SPEAKER 3W16Ω395/415mm R/B/W W/CASE.
15 9KD3006009V0R AL N * HRN ASSY 6P 135MM UL1061#30
16 9KD3030046A0R AT N * HRN ASSY LVDS 2X15P TO 30P 95mm W/LOCK
17 9KD301400820R AR N * HRN ASSY 2X7P TO 6P/4P 440/520mm
18 9KD08T264C02R AR N * TOP VESA HOLDER,VT264C.
19 9KD02T264C04R AM N * BASE SUPPORT,VT264C.
20 9KD000001000R AE N * BOLT,#4-40x12.5,Ni ROHS.
21 9KD05G224G02R BA N * ASSY MAIN CHASSIS ASEAN-L10,VG224G.
22 9KD476640900R AE N * SCREW,B,CROSS,W/W-SPR,M4*42,Zn,ROHS.
23 9KD10T421J01R AF N * WIRE CLIP,CH-01S-V0,VT421J.
24 9KD10T321H02R AF N * WIRE CLIP,CHR-05-V0,VT321H
25 9KD799001010R AN N * ADAPTER RF JACK/ PAL PLUG (Philippines)
26 9KD416606901R AC N * SCREW,B,CROSS,M4*6,Zn-black
27 9KD146306200R AB N * SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc
28 9KD112322100R AB N * SCREW,P,CROSS,T.T-M3*4.5,Zn,ROHS
29 9KD018303900R AB N * SCREW,I,CROSS,M3*3,Zn-BLK,ROHS
30 9KD112310500R AE N * SCREW,P,CROSS,T.T-3*10,BLK-Zn
31 9KD016306900R AC N * SCREW,I,CROSS,Φ5.5,T3*6,BLK-Zn
32 9KD412608500R AD N * SCREW,B,CROSS,T.T-4*8,BLK ROHS
33 9KD212612120R AD N * SCREW,B,CROSS,T.T-4*12,BLK ROHS
34 9KD146304200R AC N * SCREW,P,CROSS,W/WAS,M3*4,Zn-Cc,ROHS

71

Vous aimerez peut-être aussi