Académique Documents
Professionnel Documents
Culture Documents
NECS-W_0604_1204_201211_EN
NECS-W
r HFC
R-410A
(The photo of the unit is indicative and may change depending on the model)
NECS-W
SUMMARY 0604 - 1204
Liability disclaimer Climaveneta declines any liability derived from the bulletin’s
This bulletin is not exhaustive about: installation, use, safety use.
precautions, handling and transport. Refer to “General Manual This bulletin is of exclusive property of Climaveneta, and all
for Installation” for further informations. forms of copy are prohibited.
This bulletin refers to standard executions, in particular The data contained herein are subject to variation without no-
for dimension, weight, electric, hydraulic, aeraulic and refriger- tice.
ant connections (whereas applicable). Contact Climaveneta
Commercial Office for further drawings and schemes.
1. PRODUCT PRESENTATION
NECS, the new CLIMAVENETA R410A proposal The scroll compressor has been expressly redesigned for use
with the new gas and is now even more compact and silent
Scroll compressors, featuring high efficiency, low vibrations than before.
and low noise emissions.
Flexible range. Available from 113 – 341 kW with 9 sizes and Complete versatility
5 versions. NECS-W units are designed to fully satisfy any application or
Part load efficiency with EER > 4.3 installation needs throughout a complete range of models, hy-
New controller with QuickMind. dronic configurations and accessories. NECS-W is available in
Idrorelax, for turning your ideas into reality. chiller mode (chilled water production), heat pump for hot wa-
ter production (plus possible water side reversal) NECS-WH
and finally heat pump with “refrigerant side reversal” NECS-
Climaveneta introduces its new NECS-W range of chillers and
WN (chilled/hot water production).
heat pumps with scroll compressors, plate exchangers and R-
410A, with both one-circuit two compressors and two-circuit High efficiency at partial load
four compressors, focused on maximum efficiency and mini- Climaveneta has designed NECS-W units with the goal of
mum noise emission. guaranteeing high efficiency at part load. The result achieved
in the new single-circuit dual-compressor is an ESEER up to
Why R-410A 6.01, equivalent to a 33% saving in seasonal energy consump-
Although R-410A is a blend, it behaves just like a pure gas and tion compared to traditional R-407C double-circuit unit.
features a negligible temperature glide. Thanks to its outstand-
ing heat conductivity, R-410A contributes towards achieving
high system efficiency. R-410A is also an ecological gas be-
cause its high efficiency reduces electricity consumption and
consequently CO2 emissions and because it does not damage
the ozone layer (ODP = 0).
Consistent with corporate culture, the NECS-W series was design of plate exchangers both on the condenser side and on
designed to offer extremely high quality products with cutting- the evaporator side.
edge technology focusing on maximum energy efficiency at These construction choices have both increased efficiency and
both full (EER) and part load (ESEER). provided extremely high levels of reliability while significantly
increasing compressor working life.
Energy efficiency at full load
NECS-W units stand out for their particularly high EER energy
efficiency index. This result was achieved by focusing on the
Energy efficiency at part load The ESEER parameter proposed by Eurovent, takes part load
Attention to energy consumption is continually gaining impor- operating conditions into account when assessing unit effi-
tance, even at European level. ciency.
The installed chiller unit works at full load only for extremely
short periods of time while most of the energy is produced with
part loads between 50 and 75%.
1.1 Energy indices ESEER and IPLV the evaporator is considered constant at 6.7°C in all load condi-
Increasingly closer attention is being paid towards the power tions, with a delta of 5°C in the full load condition.
consumption of air-conditioning equipment, both in Europe and The multipliers 1, 42, 45 e 12 are the cooling performance coef-
elsewhere. ficients in various load conditions statistically calculated by ARI
For many years in the United States, reference has not just on the basis of surveys conducted, for various types of build-
been made to efficiency at rated conditions. A valuation index ings and operating conditions, in 29 American cities.
is used which considers marginal operation of the unit at rated
conditions as well as the increased usage when the separation ESEER Comparison:
stages of the cooling compressors are used. NECS-W single-circuit vs. traditional dual-circuit unit.
The valuation index adopted in the United States is called IPLV The comparison proves that the new single-circuit NECS-W
(Integrated Part Load Value) and is defined in the regulations units with R-410A feature significantly greater energy efficiency
issued by ARI (American Refrigeration Institute). (ESEER + 38%) over traditional dual-circuit units with R-407C.
ARI Standard
IPLVARI =(1*EER100% + 42*EER 75% + 45*EER50% + 12*EER25%) /100
Single circuit R-410A Two scroll - two circuit R-407C NECS-W 202 vs a traditional R407-C unit
Proposal EECCAC The real power calculation can be obtained more correctly in a
ESEER = (3*EER100% +33*EER75% + 41*EER50% + 23*EER25%)/100 “dynamic” form, that is, considering the load performance curve
at different external temperatures, the location and the refer-
ence number of operating hours.
Evaporator temp. leaving 6,7°C
These figures will allow plant consultants and designers to
DeltaT full load 5°C
make their evaluations depending on the type of building, the
Load 100% 75% 50% 25%
place of installation and the type of heat load. etc.. They can
Cond. water temp. 30°C 26°C 22°C 18°C
also determine the energy index using the method that best re-
flects plant requirements and can make comparisons between
Using the energy indices
similar or equivalent systems using the same reference unit.
After establishing which index to use and estimating the total
power required by the system in the summer mode (in kWh),
we can calculate seasonal electricity consumption (in kWh) us-
ing the following formula:
All the two-compressor units are equipped, as a standard, with commitment to continually developing its electronics technol-
the “W3000 Base” keyboard with LED display. ogy. The heat pumps, moreover, are fitted with the original
On the four-compressor units the user friendly “W3000 Com- Climaveneta defrosting control system called “Smart Defrost”
pact” keyboard with LCD is installed as a standard; also avail- which considerably reduces defrosting times, thus improving
able, on demand, for the two compressors units. the energy performance of the unit. Interfaces with BMS sys-
The “W3000 Compact” on board keyboard can be connected to tems: METASYS®, MODBUS®, LONWORKS®, SIEMENS®,
a remote keyboard with LCD display. TREND®.
Main functions: QuickMind, local and remote FWS supervi- Black Box logs data relative to 200 alarm events which can be
sion, dual setpoint management, etc., confirm Climaveneta’s printed with a personal computer.
QuickMind is a special control unit which monitors the main op- water content of just 2.5 l/kW and considerably reduces outlet
erating parameters, predicts system behaviour and anticipates temperature fluctuations. The above graph shows that outlet
unit settings in order to constantly optimise performance; it al- temperature fluctuations with QuickMind are limited to 4.3°C
lows both return and delivery water temperatures to be chosen as opposed to 7.54°C if the traditional adjustment system were
as adjustment parameters. It can reduce outlet temperature used, without even ensuring an acceptable minimum compres-
fluctuations even with a small amount of water in the system. sor start time.
When, for dual-compressor chillers featuring a maximum of 12
start-ups per hour and using a traditional adjustment system,
the minimum recommended water content is 5.5 l/kW, Quick-
Mind ensures the same chiller operates correctly even with a
Integrated Hydronic Unit (Optional) - External water connections with Victalic prearrange-
(Not available on NECS-WH) ment
The NECS-W series has been designed to reduce instal-
lation work to a minimum. Available configurations
The integrated hydronic unit incorporates all the hydrau- Hydronic group 1 pump 2 poles low head
lic components, thus optimising installation space, time Hydronic group 2 pumps 2 poles low head
and costs. Hydronic group 1 pump 2 poles high head
- Horizontal one-piece centrifuge pump Hydronic group 2 pumps 2 poles high head
- Pump inlet pressure gauge
- Discharge valve Units can be equipped with up to 4 pumps, two on the
- Air vent evaporator and two on the condenser side.
- 3 bar safety valve
- Expansion tanks pre-pressurised For more details, see the “Hydronic Unit” section.
- Check valve (only if P2 is fitted)
- Y-shaped water filter with stainless steel mesh (option-
al)
Refrigerant circuit
Main components of the refrigerant circuit:
- dryer filter,
- liquid line sight glass with humidity indicator,
- externally equalised thermostatic valve,
- high pressure safety valve,
- high and low pressure switches,
- high and low pressure gauges.
Notes:
1 Evaporator water (in/out) = 12°C/7°C, condenser water (in/out) = 30°C/35°C, based on Eurovent Standard
2 Values in compliance with EN14511-3:2011
3 Average sound pressure level, at 10m distance, unit in a free field on a reflective surface; non-binding value obtained from the sound power level.
4 Sound power on the basis of measurements made in compliance with ISO 9614 and Eurovent 8/1 for Eurovent certified units; in compliance with ISO 3744 for non-certified units.
5 Unit in standard configuration/execution, without optional accessories.
- Unavailable
2
GENERAL TECHNICAL DATA NECS-W / B /H
Notes:
1 Plant (side) cooling exchanger water (in/out) 12°C/7°C; Source (side) heat exchanger water (in/out) 30°C/35°C
2 Values in compliance with EN14511-3:2011
3 Plant (side) heating exchanger water (in/out) 40°C/45°C; Source (side) heat exchanger water (in/out) 10°C/* °C (flow rate as in cooling)
4 Average sound pressure level, at 10m distance, unit in a free field on a reflective surface; non-binding value obtained from the sound power level.
5 Sound power on the basis of measurements made in compliance with ISO 9614 and Eurovent 8/1 for Eurovent certified units; in compliance with ISO 3744 for non-certified units.
6 Unit in standard configuration/execution, without optional accessories.
- Unavailable
2-H
NECS-W
COOLING CAPACITY PERFORMANCE
B
0604
Tcd 30 35 40 45 50 55 30 35 40 45 50 55 30 35 40 45 50 55
Tev 6 7 8
Pf 176 169 160 151 141 130 181 174 165 156 146 134 187 179 171 161 151 139
Pat 35,1 38,7 43,1 48,1 53,7 60,1 35,3 38,9 43,2 48,2 53,9 60,3 35,5 39,1 43,4 48,4 54,1 60,5
Qev 30,3 29,0 27,6 26,0 24,2 22,3 31,2 29,9 28,5 26,9 25,1 23,2 32,2 30,9 29,4 27,7 25,9 24,0
Dpev 35,8 32,8 29,7 26,3 22,9 19,4 38,1 35,0 31,6 28,1 24,5 20,9 40,5 37,2 33,7 30,0 26,2 22,4
Pt 211 207 203 199 195 190 217 213 209 204 200 195 223 218 214 209 205 200
Qcd 36,1 35,5 34,8 34,1 33,3 32,5 37,1 36,5 35,8 35,0 34,2 33,3 38,1 37,4 36,7 35,9 35,1 34,2
Dpcd 36,3 35,0 33,7 32,3 30,8 29,3 38,3 37,0 35,5 34,0 32,5 30,9 40,4 38,9 37,4 35,8 34,2 32,5
Tev 9 10 11
Pf 193 185 176 166 156 144 198 190 181 171 161 149 204 195 186 176 166 154
Pat 35,7 39,3 43,6 48,6 54,2 60,6 35,9 39,5 43,7 48,7 54,3 60,7 36,1 39,6 43,8 48,8 54,4 60,7
Qev 33,2 31,8 30,3 28,6 26,8 24,8 34,1 32,7 31,2 29,5 27,7 25,7 35,1 33,7 32,1 30,4 28,5 26,6
Dpev 42,9 39,4 35,8 31,9 28,0 24,1 45,5 41,8 37,9 33,9 29,9 25,8 48,1 44,2 40,1 36,0 31,8 27,6
Pt 228 224 219 215 210 205 234 229 225 220 215 210 240 235 230 225 220 215
Qcd 39,1 38,4 37,6 36,8 36,0 35,1 40,1 39,3 38,5 37,7 36,9 36,0 41,1 40,3 39,5 38,6 37,7 36,9
Dpcd 42,5 40,9 39,3 37,6 36,0 34,2 44,7 43,0 41,3 39,5 37,8 36,0 47,0 45,1 43,3 41,4 39,6 37,8
0704
Tcd 30 35 40 45 50 55 30 35 40 45 50 55 30 35 40 45 50 55
Tev 6 7 8
Pf 206 196 186 175 163 150 213 203 192 181 169 156 219 209 198 187 174 162
Pat 40,9 45,0 49,8 55,3 61,5 68,5 41,2 45,2 50,0 55,5 61,8 68,8 41,4 45,5 50,3 55,8 62,0 69,0
Qev 35,4 33,8 32,0 30,1 28,0 25,9 36,6 34,9 33,1 31,1 29,0 26,8 37,8 36,0 34,1 32,2 30,0 27,8
Dpev 33,9 30,8 27,6 24,4 21,2 18,1 36,1 32,9 29,5 26,1 22,8 19,4 38,5 35,0 31,5 27,9 24,4 20,9
Pt 247 241 236 230 224 219 254 248 242 236 230 225 261 255 249 243 237 231
Qcd 42,2 41,3 40,4 39,4 38,4 37,4 43,5 42,5 41,5 40,5 39,5 38,5 44,7 43,6 42,6 41,6 40,5 39,5
Dpcd 35,7 34,1 32,6 31,0 29,5 28,0 37,8 36,1 34,4 32,8 31,2 29,6 39,9 38,1 36,3 34,6 32,9 31,2
Tev 9 10 11
Pf 226 216 205 193 180 167 233 222 211 199 186 173 240 229 217 205 192 179
Pat 41,7 45,7 50,5 56,0 62,3 69,3 41,9 45,9 50,7 56,2 62,5 69,5 42,1 46,1 50,9 56,4 62,7 69,7
Qev 38,9 37,1 35,2 33,2 31,1 28,8 40,1 38,3 36,3 34,3 32,1 29,8 41,3 39,4 37,4 35,3 33,1 30,9
Dpev 40,9 37,2 33,5 29,8 26,1 22,4 43,4 39,5 35,6 31,7 27,8 24,0 46,0 41,9 37,8 33,7 29,7 25,7
Pt 268 261 255 249 243 237 275 268 262 255 249 243 282 275 268 261 255 249
Qcd 45,9 44,8 43,7 42,7 41,6 40,5 47,1 45,9 44,8 43,7 42,7 41,6 48,3 47,1 46,0 44,8 43,7 42,7
Dpcd 42,1 40,1 38,2 36,4 34,6 32,9 44,3 42,2 40,2 38,3 36,4 34,6 46,6 44,4 42,3 40,2 38,3 36,4
0804
Tcd 30 35 40 45 50 55 30 35 40 45 50 55 30 35 40 45 50 55
Tev 6 7 8
Pf 232 221 208 196 182 169 240 228 216 203 189 175 247 235 223 209 196 181
Pat 46,8 51,2 56,5 62,5 69,3 76,9 47,1 51,6 56,8 62,9 69,7 77,3 47,3 51,9 57,1 63,2 70,0 77,7
Qev 40,0 38,0 35,9 33,7 31,4 29,0 41,3 39,2 37,1 34,9 32,5 30,1 42,6 40,5 38,3 36,1 33,7 31,2
Dpev 43,1 38,9 34,8 30,7 26,6 22,7 46,0 41,6 37,2 32,8 28,6 24,4 49,0 44,3 39,7 35,1 30,6 26,3
Pt 279 272 265 258 252 245 287 280 272 265 259 252 295 287 280 273 266 259
Qcd 47,7 46,6 45,4 44,2 43,1 42,0 49,1 47,9 46,7 45,5 44,3 43,2 50,5 49,2 47,9 46,7 45,5 44,3
Dpcd 35,3 33,6 31,9 30,3 28,8 27,3 37,4 35,5 33,7 32,0 30,4 28,9 39,5 37,5 35,6 33,8 32,1 30,5
Tev 9 10 11
Pf 255 243 230 216 202 188 263 250 237 223 209 194 271 258 244 230 216 201
Pat 47,6 52,1 57,4 63,5 70,4 78,0 47,9 52,4 57,7 63,8 70,7 78,4 48,1 52,7 58,0 64,1 71,0 78,7
Qev 44,0 41,8 39,6 37,2 34,8 32,3 45,3 43,1 40,8 38,4 36,0 33,5 46,6 44,4 42,1 39,6 37,2 34,6
Dpev 52,2 47,2 42,3 37,4 32,7 28,2 55,4 50,1 45,0 39,9 35,0 30,2 58,7 53,2 47,8 42,4 37,3 32,4
Pt 303 295 287 280 273 266 311 303 295 287 280 273 319 310 302 294 287 280
Qcd 51,9 50,5 49,2 48,0 46,7 45,5 53,3 51,9 50,5 49,2 47,9 46,7 54,6 53,2 51,8 50,5 49,2 47,9
Dpcd 41,7 39,6 37,6 35,6 33,8 32,1 44,0 41,7 39,5 37,5 35,6 33,8 46,3 43,8 41,6 39,5 37,5 35,6
NECS-W NECS-W
Evaporator Condenser
Limits to exchanger water temperature are valid within the minimum - (1) Condenser air (in) 30/35 °C
maximum water flow range indicated in the Hydraulic Data section. (2) Evaporator water (in/out) 12/7 °C
(3) With temperatures down to -8°C use anti-freeze mixtures. In case of
lower temperatures, please contact our Sales Department.
cPf: cooling capacity correction factor For data concerning other kind of anti-freeze solutions (e.g. propylene
cQ flow correction factor glycol) please contact our Sales Department.
cdp pressure drop correction factor
FOULING FACTORS
The new NECS-W units can be equipped with evaporator and/ impeller. The section of shaft in contact with the liquid is made
or condenser hydronic kits. The kit incorporates the main hy- from stainless steel. Mechanical seal made from components
draulic components thus optimizing hydraulic and electrical in- in ceramics/carbon/NBR/AISI304. Three-phase electric motor
stallation space, time and costs. protected to IP55, insulation class F, suitable for continuous
Moreover NECS-W can be provided with INVERTER pumps on service.
the condenser side. This device enables the condensing pres-
sure control, through the variable speed pump, reducing pump Second pump
energy consumption. A second stand-by pump for high or low pressures is available
on request. The pumps are automatically exchanged on the
Available configurations basis of a rotation programme and the stand-by pump cuts in
Evaporator and/or condenser hydronic kit can be provided with automatically if the primary pump fails. The two-pump hydron-
following configurations: ic assembly is also fitted with check valves to ensure the unit
works correctly.
Hydronic group 1 pump low head
Hydronic group 2 pumps low head Water-side mechanical filter (optional)
Hydronic group 1 pump high head Y-filter designed and built to capture the impurities in the hy-
Hydronic group 2 pumps high head draulic circuit. It is fitted with a 0.9 mm stainless steel mesh car-
tridge which can be replaced without removing the valve body
Units can be equipped with up to 4 pumps, two on the evapora- from the piping.
tor and two on the condenser side.
2-pole pump
Low head pump with 100 kPa external static pressure.
High head pump with 200 kPa external static pressure.
Horizontal one-piece centrifuge pump with one impeller, axial
suction and radial delivery, AISI 304L stainless steel pump body
The hydronic group comprises: The electrical panel of the unit is protected with Automatic cir-
- P Horizontal one-piece centrifuge pump. cuit breakers
- MA Hydraulic circuit pressure gauge The supply does not include the following accessories though
- SC Discharge valve these are recommended to ensure correct system operation:
- S1 Exchanger input water temperature probe - Pressure gauges upline and downline from the unit.
- S2 Exchanger outlet water temperature probe - Flexible joints on piping.
- SF Air vent - On-off valves
- VA 3 bar safety valve. - Outlet control thermometer
- VE 8-litre expansion tank, pre-pressurised to 1,5 bar - Flow switch
- VR Check valve (only if P2 is fitted)
Condensation control
Geothermal
Solutions Draw / Well Dry-Cooler
probe
Pressostatic
X --- ---
valve
Inverter --- X X
Evaporator side
Low head High head
Pf (1) Q (1) F.L.I. F.L.A. Hp F.L.I. F.L.A. Hp
Size Pump ref. Pump ref.
[kW] [m3/h] [kW] [A] [kPa] [kW] [A] [kPa]
0604 173.9 29.9 A 2.2 5.0 185 E 3.0 6.0 244
0704 202.7 34.9 A 2.2 5.0 157 F 4.0 8.1 287
0804 228.0 39.2 B 3.0 6.0 184 F 4.0 8.1 260
0904 257.9 44.4 B 3.0 6.0 16 D 5.5 10.1 288
1004 288.1 49.6 B 3.0 6.0 164 D 5.5 10.1 276
1104 328.5 56.5 C 4.0 8.1 196 D 5.5 10.1 255
1204 371.1 63.8 D 5.5 10.1 230 G 7.5 13.0 317
450
400
350
300
H [kPa]
250
F G
E D
200
150
A B C
100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85
Q [m 3/h]
Condenser side
450
400
350
300
H [kPa]
250
C
200
150
A B
100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85
Q [m 3/h]
Maximum values
A B
REMARKS:
For installation purposes, please refer to the documentation sent after the
purchase-contract. This technical data should be considered as indicative. CLI-
MAVENETA may modify them at any moment.
Water connections
Size Evaporator Condenser
Victaulic
0604 Ref. 1- 2 Ref. 3 - 4
0704 2 1/2” 2 1/2”
0804 2 1/2” 2 1/2”
0904 2 1/2” 2 1/2”
1004 2 1/2” 2 1/2”
1104 2 1/2” 2 1/2”
1204 2 1/2” 2 1/2”
LIFTING
R3
R4
R1 R2
INSTRUCTIONS: REMARKS:
For installation purposes, please refer to the documentation sent after the purchase-
- Make sure that all the panels are firmly fixed in place before moving the unit. contract.
- Before lifting it, check the weight on the CE label. This technical data should be considered as indicative. CLIMAVENETA may modify
- Use all, and only, the lifting points provided, them at any moment.
- Use slings of equal length,
- Use a spread-bar (not included)
- Move the unit carefully and avoid abrupt movements.
Pipe threads where pressure-tight joints are not made on the Pipe threads where pressure-tight joints are made on the
threads - Designation, dimensions and tolerances. threads - Designation, dimensions and tolerances.
Designation Description
Internal cylindrical threads where pressure-tight joints are made on the threads, defined by stand-
UNI ISO 7/1 - Rp 1 1/2 ard UNI ISO 7/1
Conventional ø 1 1/2”
Internal cylindrical threads where pressure-tight joints are made on the threads, defined by stand-
UNI ISO 7/1 - Rp 2 1/2 ard UNI ISO 7/1
Conventional ø 2 1/2”
Internal cylindrical threads where pressure-tight joints are made on the threads, defined by stand-
UNI ISO 7/1 - Rp 3 ard UNI ISO 7/1
Conventional ø 3”
External conical threads where pressure-tight joints are made on the threads, defined by standard
UNI ISO 7/1 - R 3 UNI ISO 7/1
Conventional ø 3”
Internal cylindrical threads where pressure-tight joints are not made on the threads, defined by
standard UNI ISO 228/1
UNI ISO 228/1 - G 4 B
Tolerance class B for external thread
Conventional ø 4”
Flange Nominal Diameter: 80 mm th.
DN 80 PN 16
Nominal Pressure: 16 bar
Climaveneta France
3, Village d’Entreprises
ZA de la Couronne des Prés
Avenue de la Mauldre
78680 Epône
France
Tel +33 (0)1 30 95 19 19
Fax +33 (0)1 30 95 18 18
info@climaveneta.fr
www.climaveneta.fr
Climaveneta Deutschland
Rhenus Platz 2
59439 Holzwickede
Germany
Tel +49 2301 91222-0
Fax +49 2301 91222-99
info@climaveneta.de
www.climaveneta.de
Climaveneta
España - Top Clima
Londres 67, 1 4
08036 Barcelona
Spain
Tel +34 934 195 600
Fax +34 934 195 602
topclima@topclima.com
www.climaveneta.com
www.climaveneta.com