Académique Documents
Professionnel Documents
Culture Documents
We recommend that for future reference you To reduce the risk of electric shock:
record the Serial Number of your Sewing
Machine in the space provided. • The machine should never be left unattend-
ed when plugged in. Always unplug the
Refer to illustration for location of Serial machine from the electric outlet immediately
Number on your machine. after using and before cleaning.
WARNING
• Disconnect the power-line plug from the • When sewing, keep fingers away from all
socket outlet or switch the machine off when moving parts. Special care is required
making any adjustments in the needle area, around the sewing machine needle.
such as threading needle, changing needle,
changing throat plate or changing presser • Do not pull or push fabric while stitching. It
foot, etc. may deflect the needle causing it to break.
• Always unplug the machine from the electri- • Before removing the bobbin case, remove
cal outlet when removing covers, lubricating, plug from the socket outlet.
or when making any other user servicing
adjustments mentioned in the Operator's • For double insulated machines, when serv-
Guide. icing use only identical replacement parts.
• Do not attempt to adjust the motor belt. • Never operate the machine if it has a dam-
Contact your nearest Service Center should aged cord or plug, if it is not working proper-
any adjustment be required. ly, if It has been dropped or damaged, or
dropped into the water. Return the machine
• Do not unplug by pulling on cord. To unplug, to the nearest authorized dealer or Service
grasp the plug, not the cord. Center for examination, repair, electrical, or
mechanical adjustment.
• Handle the foot controller with care and
avoid dropping it on the floor. Be sure not to • Never operate the machine with any air
place anything on top of it. openings blocked. Keep ventilation open-
ings of the machine and foot controller free
• Always use the proper throat plate. The from the accumulation of lint, dust, and
wrong plate can cause the needle to break. loose cloth.
• Do not use bent needles. • Never drop or insert any object into any
opening.
This product is suppressed for radio and tele- Neither core is to be connected to the earth
vision interference with the International terminal of a three-pin plug.
Electrotechnical Commission requirements of
the CISPR. • Do not use outdoors
Machines for Great Britain: • Do not operate where aerosol (spray) prod-
ucts are being used or where oxygen is
Machines for Great Britain and some other being administered.
countries having similar wiring standards are
shipped from the factory without a plug for • Do not allow to be used as a toy. Close
connection to the mains. The wires in this attention is necessary when the machine is
mains lead are coloured in accordance with used by or near children.
the following code:
The following accessories furnished with your 5. Zipper foot (E) is used for inserting zip-
sewing machine are designed to simplify your pers and stitching corded seams.
sewing projects and increase the versatility of
your machine. 6. Friction free spool holder is used to hold
various size spools and allows thread to
The letter in a circle adjacent to the illustrated unwind smoothly. The spool does not turn.
part is reproduced on the part itself to help
you select the correct attachment for the type 7. Small thread spool holder (Q) for use
of work you are doing. with small diameter spools of thread.
4. Buttonhole presser foot (L) is used with 11. Blindstitch hem presser foot is used to
the General Purpose Needle Plate to make position the hem for blindstitch hemming.
four-step buttonholes
10
11
12
13
14
15
Winding a bobbin is quick and easy when you follow the directions below. Always wind the
bobbin before threading the machine and needle.
• Push in indent (1) on hand wheel disc This will stop the needle from moving.
• Place spool of thread on spool pin.
• Slide spool cap (2) firmly over rim of spool to prevent thread tangling.
• Lead thread from spool and snap into thread guide post (3).
• Wind thread clockwise around front of bobbin winder tension disc (4).
• Pass thread end, from inside, through small hole in rim of bobbin.
• Place bobbin on spindle and push it to the right
• Holding thread end, step on speed controller to run machine until desired amount of thread
is wound. (Winding stops automatically once bobbin is full).
• Cut thread; push bobbin to the left and remove it from spindle.
• Trim thread end from top of bobbin.
• Return hand wheel disc to sewing position by pressing on side opposite indent.
16
17
18
19
Basting
20
Starting a seam
21
22
23
Recommended settings
Stitch Selection: Straight Stitch
Needle Position:
Stitch Width:
Stitch Length: 2-5
Foot: General Purpose (B)
Needle Plate: General Purpose (A)
Attach feed cover plate (F)
Sewing in reverse
24
Preparation
Pattern:
Neeale position:
Stitch width:
Stitch length: 2-5
Foot: Zipper (E)
Needle plate: General Purpose (A)
25
26
The dial localized on the panel of your machine, lets you choose pattern groups.
This will see to it that the stitch pattern dial moves easier.
In order to single out the desired pattern group, just turn the dial until the corresponding letter
to this pattern group appears on the dial, under symbol .
After carrying out the embroidery selection, turn back the stitch width selector to the zig-zag
position ( ).
Adjust the stitch length as indicated on each kind of embroidery (from 1/2 to 2 1/2).
27
Note: The pattern groups selection, needle position selection and stitch width selection are
similar to zig-zag stitching.
These stitch patterns are used for sewing knits and other stretch fabrics. Flexi Stitch patterns
are made by the side to side movement of the needle along with the backward and forward
movement of the feed.
28
29
30
Zig-zag stitch
Any General General Stretch sewing
setting purpose purpose and embroidery
Multi zig-zag
stitch Special General Bar
1.0 to 2.0
purpose purpose tacking
Crescent stitch
Special General Ornamental
0 to 2.0
purpose purpose borders
Rampart stitch
Special General Borders and
1.0 to 2.0
purpose purpose smocking
Fagotting stitch
Special General Swimsuit
1.0 to 2.0
purpose purpose seams
31
Feather stitch
Special General Flexible seam
( )
purpose purpose in lingerie
Chevron stitch
Special General Classical
( ) decorative
purpose purpose
seams
Thorn stitch
Special General Ideal for
( )
purpose purpose flat-butted seam
32
Recommended settings
Stitch Selection: Zig-Zag Stitch (1 A)
Needle Position:
Stitch Width: To suit Button
Foot: Button Sewing (H)
Needle Plate: General Purpose (A)
Attach Feed Cover (F)
33
Applications
Sleeves
Buttons
34
Four-step buttonhole
35
Recommended settings.
Stitch Selection: Buttonhole Stitch (1A)
Stitch Width: Pre-set hot: Buttonhole (L)
Needle Plate: General Purpose (A)
Step 1
Step 2
36
Step 4
37
38
Stitch Width:
Stitch Length: 2-5
Foot: General Purpose (B)
Needle Plate: General Purpose (A)
39
Procedure
40
Accessory storage
41
42
43
44
1. Removing bulb
2. Replacing bulb
45
46