Académique Documents
Professionnel Documents
Culture Documents
0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
2. Terminal Function
Connector [EKG-K]
Pin
Description Connected to
No.
Idle Speed Control Actuator [OPEN] control
1 Idle Speed Control Actuator (ISCA)
output
Idle Speed Control Actuator [CLOSE] control
2 Idle Speed Control Actuator (ISCA)
output
3 Power Ground Chassis Ground
4 Power Ground Chassis Ground
5 Battery voltage supply after main relay Main Relay
6 Battery voltage supply after main relay Main Relay
Heated Oxygen Sensor [Bank 1/ Sensor 1]
7 Heated Oxygen Sensor [Bank 1/ Sensor 1]
Heater control output
8 -
9 Injector (Cylinder #1) control output Injector (Cylinder #1)
10 Engine RPM signal output EPS Control Module
11 ISG OFF switch signal input ISG OFF Switch [With ISG]
12 Start switch signal input Ignition switch
13 Electric Load signal input (Defrost) A/C Control Module, Outside Mirror
14 -
15 Alternator load signal input Alternator
Camshaft Position Sensor (CMPS) [Bank Camshaft Position Sensor (CMPS) [Bank
16
1/Exhaust] signal input 1/Exhaust]
1/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
Camshaft Position Sensor (CMPS) [Bank Camshaft Position Sensor (CMPS) [Bank
17
1/Intake] signal input 1/Intake]
18 Battery voltage supply after ignition switch Ignition Switch
19 Sensor power (+3.3V) Accelerator Position Sensor (APS) #2
20 Sensor power (+5V) Manifold absolute pressure sensor (MAPS)
21 Sensor power (+3.3V) Throttle position sensor (TPS)
22 Intake Air temperature sensor (IATS) signal input Intake Air temperature sensor (IATS)
Manifold absolute pressure sensor (MAPS)
23 Manifold absolute pressure sensor (MAPS)
signal input
24 Throttle position sensor (TPS) signal input Throttle position sensor (TPS)
25 -
Camshaft Position Sensor (CMPS) [Bank
26 Sensor ground
1/Intake]
27 Ignition coil (Cylinder #1) control output Ignition coil (Cylinder #1)
28 Ignition coil (Cylinder #2) control output Ignition coil (Cylinder #2)
29 Purge Control Solenoid Valve control output Purge Control Solenoid Valve (PCSV)
30 Battery voltage supply after main relay Main Relay
31 Cooling Fan Relay [Low] control output Cooling Fan Relay [Low]
32 Alternator PWM control output Alternator [With ISG]
33 Clutch switch signal input Clutch switch
34 -
35 Neutral Switch signal input Neutral Switch [With ISG]
36 Electrical load [Wiper] signal input Multifunction Switch
37 A/C Dual pressure switch signal input A/C Dual pressure switch
38 -
39 Vehicle speed signal input ABS/ESP Control Module [With ABS/ESP]
40 -
41 -
Crankshaft Position Sensor (CKPS) [With ISG]
A/C Pressure Transducer (APT)
42 Sensor power (+5V)
Brake Booster Vacuum Pressure Sensor [With
2/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
ISG]
43 -
Engine coolant temperature sensor (ECTS)
44 Engine coolant temperature sensor (ECTS)
signal input
45 -
46 -
47 -
Camshaft Position Sensor (CMPS) [Bank
48 Sensor ground
1/Exhaust]
49 -
50 Ignition Coil (Cylinder #3) control output Ignition Coil (Cylinder #3)
51 Injector (Cylinder #2) control output Injector (Cylinder #2)
52 Start Relay control output Start Relay
53 -
54 Immobilizer lamp control output Immobilizer Lamp
55 -
56 Crankshaft Position Sensor [A] signal input Crankshaft Position Sensor (CKPS)
57 CAN [High] Other control module
58 LIN communication (K-Line) Battery Sensor [With ISG]
59 -
60 -
Brake Booster Vacuum Pressure Sensor [With
61 Sensor ground
ISG]
62 -
63 Sensor ground Engine Coolant Temperature Sensor (ECTS)
64 -
65 -
Heated Oxygen Sensor [Bank 1/ Sensor 2] signal
66 Heated Oxygen Sensor [Bank 1/ Sensor 2]
input
67 -
68 -
3/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
69 -
70 Sensor ground Knock sensor (KS)
Heated Oxygen Sensor [Bank 1/ Sensor 2]
71 Heated Oxygen Sensor [Bank 1/ Sensor 2]
Heater control output
72 -
73 -
74 Injector (Cylinder #3) control output Injector (Cylinder #3)
75 Fuel Pump Relay control output Fuel Pump Relay
76 A/C compressor relay control output A/C compressor relay
77 Power ground Chassis ground
78 Sensor ground Crankshaft Position Sensor (CKPS)
79 CAN [Low] Other control module
80 Immobilizer communication line Immobilizer control module
81 -
82 -
83 Sensor ground Manifold absolute pressure sensor (MAPS)
84 -
85 Sensor ground Throttle position sensor (TPS)
86 Sensor ground Heated Oxygen Sensor [Bank 1/ Sensor 1,2]
Heated Oxygen Sensor [Bank 1/ Sensor 1] signal
87 Heated Oxygen Sensor [Bank 1/ Sensor 1]
input
88 -
89 Startar Relay Monitoring signal input Startar Relay
Brake Booster Vacuum Pressure Sensor signal Brake Booster Vacuum Pressure Sensor [With
90
input ISG]
91 Knock sensor (KS) signal input Knock sensor (KS)
CVVT Oil Control Valve [Bank 1/Intake] control
92 CVVT Oil Control Valve (OCV) [Bank 1/Intake]
output
CVVT Oil Control Valve [Bank 1/Exhaust] control
93 CVVT Oil Control Valve (OCV) [Bank 1/Exhaust]
output
94 Auto Stop Lamp output ISG OFF Switch
4/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
5/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
Cooling Fan Relay [Low] control Relay OFF Battery Voltage 14.12V
31 DC
output Relay ON Max. 1.0V 61.6mV
32 Alternator PWM control output
6/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
7/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
51 Injector (Cylinder #2) control output Idle Pulse Hi: Battery Voltage 13.6V
Lo: Max. 1.0V 336mV
Vpeak: Max. 80V 69.7V
52 Start Relay control output
53 -
Lamp OFF Battery Voltage 12.6V
54 Immobilizer lamp control output DC
Lamp ON Max. 1.0V 20mV
55 -
8/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
9/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
2. Terminal Function
Connector [EKG-K]
Pin
Description Connected to
No.
Idle Speed Control Actuator [OPEN] control
1 Idle Speed Control Actuator (ISCA)
output
Idle Speed Control Actuator [CLOSE] control
2 Idle Speed Control Actuator (ISCA)
output
3 Power Ground Chassis Ground
4 Power Ground Chassis Ground
5 Battery voltage supply after main relay Main Relay
6 Battery voltage supply after main relay Main Relay
Heated Oxygen Sensor (Sensor 1) Heater
7 Heated Oxygen Sensor (Sensor 1)
control output
8 Injector (Cylinder #2) control output Injector (Cylinder #2)
9 Injector (Cylinder #1) control output Injector (Cylinder #1)
10 Engine RPM signal output Trip computer
11 -
10/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
40 -
41 -
42 -
43 -
Engine coolant temperature sensor (ECTS)
44 Engine coolant temperature sensor (ECTS)
signal input
45 -
46 -
47 -
Camshaft Position Sensor (CMPS) [Bank
48 Sensor ground
1/Exhaust] (Europe only)
49 -
50 -
51 Injector (Cylinder #3) control output Injector (Cylinder #3)
52 Start Relay control output Start Relay
53 -
54 Immobilizer lamp control output Immobilizer Lamp
55 -
56 Crankshaft Position Sensor [A] signal input Crankshaft Position Sensor (CKPS)
57 CAN [High] Other control module
58 LIN communication (K-Line) Battery Sensor [With ISG]
59 -
60 Vehicle Speed Sensor (VSS) [B] signal input Vehicle Speed Sensor (VSS)
61 -
62 -
63 Sensor ground Engine Coolant Temperature Sensor (ECTS)
64 -
65 -
Heated Oxygen Sensor [Bank 1/ Sensor 2] signal
66 Heated Oxygen Sensor [Bank 1/ Sensor 2]
input
67 -
12/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
68 -
69 -
70 Sensor ground Knock sensor (KS)
Heated Oxygen Sensor [Bank 1/ Sensor 2]
71 Heated Oxygen Sensor [Bank 1/ Sensor 2]
Heater control output
72 -
73 -
74 Injector (Cylinder #3) control output Injector (Cylinder #3)
Fuel Pump Relay control output Fuel Pump Relay [With Immobilizer]
75
A/C compressor relay control output A/C compressor relay[Without Immobilizer]
Fuel Pump Relay control output Fuel Pump Relay [Without Immobilizer]
76
A/C compressor relay control output A/C compressor relay[With Immobilizer]
77 Power ground Chassis ground
78 Sensor ground Crankshaft Position Sensor (CKPS)
79 CAN [Low] Other control module
80 Immobilizer communication line Immobilizer control module
81 -
82 Vehicle Speed Sensor (VSS) [A] signal input Vehicle Speed Sensor (VSS)
83 Sensor ground Manifold absolute pressure sensor (MAPS)
84 -
85 Sensor ground Throttle position sensor (TPS) #1,2
86 Sensor ground Heated Oxygen Sensor (Sensor 1,2)
Heated Oxygen Sensor [Bank 1/ Sensor 1] signal
87 Heated Oxygen Sensor [Bank 1/ Sensor 1]
input
88 -
89 Startar Relay Monitoring signal input Startar Relay
90 -
91 Knock sensor (KS) signal input Knock sensor (KS)
CVVT Oil Control Valve [Bank 1/Intake] control
92 CVVT Oil Control Valve [Bank 1/Intake]
output
CVVT Oil Control Valve [Bank 1/Exhaust] control CVVT Oil Control Valve [Bank 1/Exhaust] (Europe
13/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
93
output only)
94 -
15/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
Cooling Fan Relay [Low] control Relay OFF Battery Voltage 14.12V
31 DC
output Relay ON Max. 1.0V 61.6mV
32 Alternator PWM control output
33 -
34 -
35 -
36 -
A/C Duel Pressure switch signal
37 A/C ON Analog Max. 4.8V 1.88V
input
38 -
Hi: Min. 4.5V 12.2V
Lo: Max. 1.0V 0V
Idle
Freq.:
72.2Hz
39 Vehicle speed signal input Pulse
Hi: Min. 4.5V 12.2V
Vehicle Run Lo: Max. 1.0V 0V
(30km) Freq.:
212Hz
40 -
41 -
42 -
43 -
Engine Coolant Temperature
44 Idle Analog 0.5 ~ 4.5V 1.43V
Sensor signal input
45 -
46 -
47 -
16/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
49 -
50 -
Hi: Battery Voltage 13.6V
Injector (Cylinder #3) control
51 Idle Pulse Lo: Max. 1.0V 336mV
output
Vpeak: Max. 80V 69.7V
52 Start Relay control output
53 -
Lamp OFF Battery Voltage 12.6V
54 Immobilizer lamp control output DC
Lamp ON Max. 1.0V 20mV
55 -
Fuel Pump Relay control output Relay OFF Battery Voltage 12.8V
DC
75 [With Immobilizer] Relay ON Max. 1.0V 400mV
Fuel Pump Relay control output Relay OFF Battery Voltage 12.8V
DC
76 [Without Immobilizer] Relay ON Max. 1.0V 400mV
88 -
Startar Relay Monitoring signal
89
input
90 -
Knocking Variable
91 Knock Sensor signal input
Normal Frequency
19/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
20/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
21/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
22/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
23/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
24/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
25/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
26/27
2012 > G 1.0 DOHC > Fuel System > Engine Control System > Engine Control Module (ECM) > Schematic Diagrams
27/27