Académique Documents
Professionnel Documents
Culture Documents
UFR II/PCL/PS
Printer Kit-R1
SERVICE
MANUAL
DU7-1222-000
FEBRUARY 2007
REV. 0
COPYRIGHT 2006 CANON INC. CANON UFR II/PCL/PS Printer Kit-R1 REV. 0 PRINTED IN U.S.A.
Application
This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation,
maintenance, and repair of products. This manual covers all localities where the products are sold. For this reason,
there may be information in this manual that does not apply to your locality.
Corrections
This manual may contain technical inaccuracies or typographical errors due to improvements or changes in
products. When changes occur in applicable products or in the contents of this manual, Canon will release technical
information as the need arises. In the event of major changes in the contents of this manual over a long or short
period, Canon will issue a new edition of this manual.
The following paragraph does not apply to any countries where such provisions are inconsistent with local law.
Trademarks
The product names and company names used in this manual are the registered trademarks of the individual
companies.
Copyright
This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied,
reproduced or translated into another language, in whole or in part, without the written consent of Canon Inc.
Caution
Use of this manual should be strictly supervised to avoid disclosure of confidential information.
Introduction
Symbols Used
This documentation uses the following symbols to indicate special information:
Symbol Description
Indicates an item requiring disconnection of the power plug from the electric outlet.
Indicates an item intended to provide notes assisting the understanding of the topic in
question.
Memo
The descriptions in this Service Manual are subject to change without notice for product improvement or other
purposes, and major changes will be communicated in the form of Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service Manual and all
relevant Service Information bulletins and be able to identify and isolate faults in the machine."
Contents
Contents
Chapter 1 Specifications
1.1 Specifications..................................................................................................... 1-1
1.1.1 Licence Option composition (USA)iR5055/5065/5075 ........................................ 1-1
1.1.2 Printer accessory configuration(USA/AU).............................................................. 1-2
1.1.3 License configuration of the printer option(USA/AU) ........................................... 1-2
1.1.4 UFR II Printer Driver .................................................................................................. 1-3
1.1.5 PCL Printer Driver...................................................................................................... 1-6
1.1.6 PS Printer Driver ........................................................................................................ 1-7
1.1.7 Basic Specification(Direct Print) .............................................................................. 1-8
1.1.8 Limitations(Direct Print)............................................................................................. 1-9
Chapter 2 Functions
2.1 Basic Function ................................................................................................... 2-1
2.1.1 Canon Driver Information Assist Service (DIAS) .................................................. 2-1
2.1.2 FTP Printing ................................................................................................................ 2-2
2.1.3 Processing on System............................................................................................... 2-3
2.1.4 Up to 50 mm of Gutter............................................................................................... 2-4
2.1.5 Secured Print Jobs..................................................................................................... 2-5
2.1.6 Format Settings .......................................................................................................... 2-7
2.1.7 Staple & Group ........................................................................................................... 2-9
2.1.8 Custom Paper Size Settings Unit(Millimeter-Inch) ............................................... 2-9
2.1.9 Application Color Matching Priority ....................................................................... 2-10
2.1.10 Use Skip Blank Pages Mode................................................................................ 2-11
2.1.11 What's the Direct Print? ........................................................................................ 2-12
2.1.12 Outline of PDF Direct Print ................................................................................... 2-13
2.1.13 Reference Printing ................................................................................................. 2-13
2.1.14 IPPS Print ............................................................................................................... 2-14
Chapter 3 Installation
3.1 Installation procedure ....................................................................................... 3-1
3.1.1 Overview of the Installation Procedure................................................................... 3-1
Chapter 4 Maintenance
Contents
SPECIFICATIONS
Contents
Contents
1.1 Specifications........................................................................................................ 1-1
1.1.1 Licence Option composition (USA)iR5055/5065/5075 ................................................1-1
1.1.2 Printer accessory configuration(USA/AU)....................................................................1-2
1.1.3 License configuration of the printer option(USA/AU)..................................................1-2
1.1.4 UFR II Printer Driver.....................................................................................................1-3
1.1.5 PCL Printer Driver.........................................................................................................1-6
1.1.6 PS Printer Driver............................................................................................................1-7
1.1.7 Basic Specification(Direct Print)...................................................................................1-8
1.1.8 Limitations(Direct Print) ...............................................................................................1-9
Chapter 1
1.1 Specifications
1.1.1 Licence Option composition (USA)iR5055/5065/5075
0015-9463
T-1-1
Lisence Option
UFR II/PCL/PS Printer Kit-R1
Universal Send Kit-F1
Universal Send Searchable PDF Kit-A1
Universal Send PDF Security Feature Set-A1
Remote Operator's Software Kit-A2
Digital User Signature PDF Kit-A1
1GB
Encrypted Secure Print Software-C1
HDD Date Erase Kit-A1
Access Management System Kit-A1
Barcode Printing Kit-A1
Secure Watermark-A1 USA
Web Access Software-F1
T-1-2
Hard Option
1-1
Chapter 1
Since every printer accessory is a license accessory, it is necessary to follow the LMS instructions, obtain the
number of license information, and enter it into the iR host machine.
UFR II
PCL
PS
TIFF6
NW-SCAN
PDF Direct
BarDIMM
F-1-1
T-1-3
How to handle the license option of which multiple functions are integrated to 1 license:
Conventionally in the Send option, in case of integration of multiple functions into 1 license option, multiple
license certificates for each function had been packed with the machine.
Inactivation of the license transfer had been available for each function.
Such license option product as [UFR II+PCL] or [PCL+PS] has 1 integrated license certificate.
Registration of 1 license information concurrently activates multiple functions such as [UFR II+PCL] or
1-2
Chapter 1
[PCL+PS].
Inactivation of the license transfer inactivates the transfer of all the activated printer options collectively.
No separate transfer inactivation is available.
Separate inactivation of the license from the service mode screen results in the NG message.
Notabilia with regards to the license transfer inactivation:
In the standard option settings for the host machine, due to the lack of transfer inactivation information, no
license transfer to the other host machine of the same model is available.
[Invalidating the License for Transfer to a Different Device] can only license option.
Ex.1
The host machine A is the one which employs UFR II as a standard.
The newly-purchased host machine B is a copier-only one.
Want to change the host machine B to a printer model by transfer inactivation of UFR II license in the host
machine A.
->In this case, as there is no transfer inactivation information in the host machine A, the license cannot be
transferred to the host machine B.
Ex.2
The host machine A is a copier-only machine. The UFR II option was purchased to register the license
information.
The newly-purchased host machine B is a copier-only one.
Want to change the host machine B to a printer model by transfer inactivation of UFR II license in the host
machine A.
->In this case, as there is a transfer inactivation information in the host machine A, the license can be
transferred to the host machine B.
How to confirm the activated printer option license:
The options displayed by selecting [counter confirmation key > device configuration confirmation] for the
users in the operation panel are individual functions (such as UFR II+ PCL), not the names of the purchased
options.
Consequently, the license certificate is the only way to see the combination of options.
Enter the service mode level 2 and go to the service mode described below. Then the license condition is
displayed and transfer inactivation can be executed.
Copier>Option>LCNS-TR
The field No.1 in the table below shows the activated/inactivated condition of UFR II, PCL, and PS in the
service mode.
*- marked service code must be used for the license transfer inactivation. Other operations do not work
appropriately.
Font Handling:
Device fonts are not used as the printing uses the UFR II driver.
1-3
Chapter 1
Note.
Each font becomes usable by the font addition to Windows.
Paper Size:
T-1-4
T-1-5
Non-default paper:
T-1-6
T-1-7
1-4
Chapter 1
0mm mode
T-1-8
0mm Mode
Distance between the paper edge and the
Effective print area(mm)
printing available area (mm)
Main scaning Sub scaning Main scaning Sub scaning
Custom Size
94.0 142.00 2.50 Top:4.0 Bottom:2.0
Minimum
Custom Size
292.00 414.00 2.50 Top:4.0 Bottom:2.0
Maximum
Long sheet
292.00 624.00 2.50 Top:4.0 Bottom:2.0
Maximum
1-5
Chapter 1
T-1-10
Finishing:
T-1-11
Z fold
Finisher Rotate Shift Staple Punch Saddle
C fold
None OK N/A N/A N/A N/A N/A
Shift Tray N/A OK N/A N/A N/A N/A
Finisher-AD1 N/A OK OK OK*1 N/A OK*2
Saddle Finisher-AD2
N/A OK OK OK*1 OK OK*2
Data prossessing
600dpi
Supported operating systems
FONT HANDLING:
-PCL5
HP-GL/2 Mode
Texts are handled in the PCL mode, or in the HP-GL/2 mode if:
1.Characters are clipped.
2.Characters are rotated.
1-6
Chapter 1
Raster Mode
Use of a device font is determined by the driver setting.
If a device font is used, the Raster Mode will handle data the same as the HP-GL/2 Mode.
If not, the following restrictions will be imposed.
*GDI Raster Fonts unavailable 1 byte fonts such as Courier, MS Sans Serif, MS Serif, etc.
*GDI Vector Fonts available 1 byte fonts such as Modern, Roman, Script, etc.
*TrueType Fonts available 1 byte fonts such as Arial, Courier New, Symbol, Times New Roman, etc.
NOTE:
GDI Vector Fonts and TrueType Fonts become available only after added to Windows.
Data prossessing
600dpi
Supported operating systems
Target Printer:
Apple LaserWriter8500 for command
OKI MICROLINE800PS2LT for print quality
Target PDL:
Adobe PostScript Level3 3011
Note. Omit advanced feature of RedBook.
FONT HANDLING:
PS3
PostScript PDL boards support the following font types.
-Type 0, 1, 2, 3, 4, 5, 6, 9, 10, 11, 14, 32 and 42
-CIDFontType 0, 1, 2 and 4
PPD V2.20
-MacOS X(10.2.8 or later)
-MacOS (9.1 or later, LaserWriter that supports since MacOS9.1 is necessary.)
-OS that operates PageMaker or QuarkXPress for Windows
1-7
Chapter 1
T-1-12
Specification/F Content
unctions
Indispensable option UFR II/PCL/PS Printer Kit, PCL/PS Printer Kit, PS Printer Kit
Indispensable Environment Memory Size : 1GB
Corresponde PDF Ver1.4 or It prints by the specification in accordance with PDF Ver1.4 or lower
nce PDF lower versions.
PDF Ver1.5 It prints by the specification in accordance with PDF Ver1.5.
However, the following items are not supported.
JBIG2 decoder
JPX(JPEG2000) decoder
File Specifications (Reference to an external file is not
supported.)
Public Key Security Handler (Support is limited to the PDF
Standard Security Handler.)
PS XObject
Transfer Functions
Halftones
Transparency Groups
Free Text Annotations (XHTML, XML, and CSS are not
supported.)
Field Dictionaries (Rich Text strings are not supported.)
Digital Signatures (A signature will be printed although its
authenticity will not be verified. If an icon exists to indicate the
presence of a signature in the PDF file or of an edited signature,
printing will still occur without an indication of authenticity.)
File Identifiers (Reference to an external file is not supported.)
Output Intents
Open Prepress Interface (OPI)
PDF Ver1.6 or The PDF interpreter has been designed in keeping with PDF Ver
upper 1.5; as such, new mechanisms associated with Ver 1.6 are not
supported.
Correspondence TIFF TIFF Ver 6.0
1-8
Chapter 1
Specification/F Content
unctions
Paper Printing area Horizontal scanning line : Parts except blank of 4.0mm
handling Vertical scanning line :
Parts except blank of
Top:4.0mm
Bottom:4.0mm
Paper size It is the same as the main body specification.
1-9
Chapter 1
Print of each annotation is shown below. When NG is placed, the annotation cannot be printed.
T-1-13
Can be
Annotation type printed? Remarks
Text OK
Link OK
FreeText OK XHTML, XML, CSS are not support
Line OK
Square and Circle OK
Polygon and Polyline OK
Text Markup OK
Caret OK
Rubber Stamp OK
Markup OK
Ink OK
Popup NG PDF Viewer function
FileAttachment OK
Sound OK
Movie OK Movie poster image only support
Screen OK
Widget OK
Printer's Mark OK
Trap Network OK
Watermark OK
Encrypted file
Decoding the PDF file encrypted by encryption algorithm RC4 128bit is supported.
- The cryption key is input with remote UI as a password (maximum : 32 characters - half size of charactor ),
forwarded to the device with the plaintext, and decoded.
- When both the user password and the owner password are set to the document, either password can be
accepted.
- When only the owner password is set to the document, entering the password is unnecessary.
If the password authentication fails, or any of the restrictions on printing applies, no printing will occur and the
session will end by indicating an error message in the control panel.
1-10
Chapter 1
Decoding is supported only if the file has been encoded using the Standard Security Handler (PDF standard).
Printing Restrictions
Introducing a PDF file not having printing permission will not initiate printing unless the following is true:
-The file has been given an owner password, and the password is entered correctly.
Introducing a PDF file having permission for low-resolution printing will not initiate printing if the following
is true:
-The file has been given a user password, but the password is entered incorrectly (i.e., an illegal password is
entered).
-The file has been given both owner password and user password, but one of them is entered incorrectly (e.g.,
an illegal password is entered).
T-1-14
1-11
Chapter 1
Halftone screen
When halftone screen is used in the file, rendering using this halftone is not conducted. The dither processing is
conducteddone.
By ignoring the halftone screen in the PDF file, since Acrobat's default print setting is "Emit halftone", the
output will be the same result as the output from Acrobat with PS.
PJTF
The job control instruction by PJTF(Portable Jot Ticket Format) is not supported. It is ignored.
Font substitution
When the European character font specified by PDF doesn't exist, it is substituted by the multiple master font.
However, it doesn't adjust the width of the character when the Chinese character font is substituted, so the
position of the output might be displaced, depending on the substituted characters. (This is same as the Adbe PS
machine).
1-12
Chapter 2
FUNCTIONS
Contents
Contents
2.1 Basic Function ................................................................................................... 2-1
2.1.1 Canon Driver Information Assist Service (DIAS) .................................................. 2-1
2.1.2 FTP Printing ................................................................................................................ 2-2
2.1.3 Processing on System............................................................................................... 2-3
2.1.4 Up to 50 mm of Gutter............................................................................................... 2-4
2.1.5 Secured Print Jobs..................................................................................................... 2-5
2.1.6 Format Settings .......................................................................................................... 2-7
2.1.7 Staple & Group ........................................................................................................... 2-9
2.1.8 Custom Paper Size Settings Unit(Millimeter-Inch) ............................................... 2-9
2.1.9 Application Color Matching Priority ....................................................................... 2-10
2.1.10 Use Skip Blank Pages Mode................................................................................ 2-11
2.1.11 What's the Direct Print? ........................................................................................ 2-12
2.1.12 Outline of PDF Direct Print ................................................................................... 2-13
2.1.13 Reference Printing ................................................................................................. 2-13
2.1.14 IPPS Print ............................................................................................................... 2-14
Chapter 2
This is a subset version of the Netspot Suite Service, supporting Driver only: we have selected Driver's functions
(mainly, the functions to acquire Device configuration information) and redesigned them. The DIAS has the
following functions:
- To acquire Device configuration information (acquisition when setting up Printer Property.)
- To make recognition in department-control printing (communication when setting up Printer Property or when
making a department-control print)
Characteristics of DIAS
- Local printer can acquire the configuration information in DIAS (DLL) only.
Local printer means a printer that is "Peer to Peer" connected with Local PC via LPR/IPP/Centronics Cable/
USB and that Spooler (Print queue) appears on the Local PC.
- Shared printer needs to have DIAS (Service) installed on printer server.
The installation of DIAS (Service) must be done via Driver installer.
Shared printer means a printer whose Spooler (Print queue) appears on the printer server (Remote PC).
- However, in some cases, DIAS (Service) needs to be installed for Local Port connection. (See "Help" >
"Troubleshoot the acquisition of configuration information".
1, WinNT4.0 OS Family (All)/ At the time of Local Port connection (LPT)
2, Win2k Server OS Family (Except Professional)/At the time of Local Port connection (LPT/USB) and
Terminal Service introduction
3, WinXP Home/Professional Edition/ServerOS 2003 Family (X86:All)/ At the time of Local Port connection
(LPT/USB) and Terminal Service introduction
2-1
Chapter 2
This device provides a FTP server for receiving print data. The device can accept print jobs sent in FTP from
client PCs. This is called FTP printing, a new feature first employed on iRC 6800. To use this feature, the FTP
Print option must be selected. It is selected by default. You can access the option by pressing Ad Func, System
Settings, Network Settings, TCP/IP Settings, and FTP Print Settings buttons. In FTP Print Settings screen, only
one pair of a user name and password can be entered for the user who can log in to the FTP server. No settings
are made for both of the fields by default.
F-2-1
Commands
The FTP server complies with the RFC 959 -- File Transfer Protocol -- but provides only printing function. Thus
the server does not support other functions required as a RFC 959 compliant server. The commands available
for the FTP client are "user," "password," "bin," "put," "bye," "hash," and "help." There is no use of other
commands since the server does not provide functions other than printing. The following lists the notes to use
the commands.
- To send print data with the command "put," set the mode to the binary mode using the command "bin." In the
ascii mode, the data cannot be sent with the command "put."
- If the user and password fields are blank, any user with any password can log in. If the user name "anonymous"
is used, any character string can be entered as the password. The device displays the string in User filed of Log
screen.
- This function is featured mainly to print prn files output from PDL drivers. The device processes text files and
the like as it receives data in LPR (and does not properly print depending on settings.) The device of PostScript-
compatible model can print PDF files, compatible with PDF V1.3.
2-2
Chapter 2
The following shows a command specification example, which you will connect the device of the IP address
"172.16.181.131" in FTP with the user name "test" and the password "test" and print the file "test.prn" in the
root directory of the drive C on the client PC.
C:\>ftp 172.16.181.131
Connected to 172.16.181.131.
220 Connection established.
User (172.16.181.131:(none)): test
331 Password required to login.
Password: Note: The password is not displayed.
230 User test logged in.
ftp> bin
200 Type set to IMAGE (binary).
ftp> put c:\test.prn
200 PORT command successful.
150 Opened BINARY data connection for file transfe
226 Transfer complete.
ftp: 15871 bytes sent in 0.00Seconds 15871000.00Kb
ftp> bye
221 Server closing down connection.
C:\>
Number of Connections and Used Ports
The maximum number of concurrent connections is three. If a user attempts to connect to the FTP server with
which three connections have been established, the user cannot log in and fails in connection. The default port
for the FTP server is 21. There is no measure provided to change the port.
The control port time-out is set to 300 seconds. You need to re-connect to the server if you have left the
connection for 300 seconds or more after logging in. The data port time-out is 60 minutes.
2.1.3 Processing on System
0015-3461
If the power is shut down during PDL data processing, all the image data temporarily stored in the hard disk
drive to be printed or stored in Mail Boxes are destroyed and the jobs are canceled. PDL data stored in the hard
disk drive immediately before a power shutdown are destroyed as the power is shut down. Processing the data
of those, therefore, will not resume when the power is turned on after the shutdown. Jobs interrupted by a power
shutdown will be displayed in the Log list with the End Code "NG (#852)."
2-3
Chapter 2
2.1.4 Up to 50 mm of Gutter
0015-3462
Up to 50 mm of the gutter can be specified. The gutter can be adjusted within a range from 0 mm to 50 mm in
1 mm increments. The local UI and the print driver have the controls for the gutter settings.
The image is shifted to the width value specified for gutter, making a margin. If the shift causes the image to
overflow from the printable area, the overflowing area is missing from the print results. The overflowing image
will not be reduced to fit into the printable area.
F-2-2
F-2-3
2-4
Chapter 2
Overview:
Secured Print is the function that a password is provided to the PDL(UFR II and PCL, PS) print job and it is sent
to the device. Then, it is rasterized on the device side, saved in the image server and output by entering the
password from the device's panel. This function is used when dealing with the documents which you do not want
other people to see, such as confidential documents.
a) Password is provided.
In order to conduct the Secured Print, the printer driver requires the user to enter the password from GUI. This
password is provided to the print job and it is sent to the device. This function can be conducted by using CPCA
protocol(UFR II and PCL, PS).
When Secured Print Job is continuing being suspended for a long time, apparatus deletes a job automatically.
There are options for automatic job deletion time -- 1, 2, 3, 6, 12, and 24 hours. With a view of security and
memory usage, no option longer than 1 day is available. The elapsed time starts after all the processes for the
PDL data and the rendering for all the image data, for which Secured Print is specified, are finished.
- Once data of a Secured Print job is printed, it is immediately deleted and cannot be printed any more.
- If the power for the controller is shut down, unprinted data of a Secured Print job is deleted from the printer.
- All the job information, represented by the paper source and output information, information of the number of
copies, and finishing information, cannot be changed on the printer.
- If the entire raster information for a Secured Print job cannot be stored in the image server (hard disk drive)
due to insufficient memory, the job results in an error, to be deleted.
- Up to 50 Secured Print jobs of image data being rendered and left unprinted can be stored.
2-5
Chapter 2
F-2-4
F-2-5
F-2-6
2-6
Chapter 2
F-2-7
A function to enable the selection of the following will be added in regard to the text used to print the result of
a job and the following notations to the lead or trail edge: Print Date, Print User Name, Print Page Number:
Font
Style
Size
Color
A change made to Format Settings will affect the following in common, and individual selection will not be
possible: Print Date, Print User Name, Print Page Number.
F-2-8
2-7
Chapter 2
F-2-9
F-2-10
2-8
Chapter 2
You can use it to enable the selection of stapling when printing in Group mode. Staple & Group permits stapling
of pages in sets.
F-2-11
If 'Store' is selected as 'Output Method' on the Finishing tab, [Staple & Group] will be grayed out, not permitting
selection.
If 'Store' is selected as 'Output Method' while selecting [Staple & Group], a switchover will take place for
[Finishing] so that [Staple & Group] will be [Collate].
2.1.8 Custom Paper Size Settings Unit(Millimeter-Inch)
0015-3465
Paper size was displayed in millimeter or inch depending on the destinations concerning the custom paper size
settings. The printer driver enables users to select the unit (Millimeter or Inch).
F-2-12
2-9
Chapter 2
There have been some cases that color reproducibility may become inappropriate if users perform color
matching in the printer driver again though they have already done it in PC.
When the checkbox for Application Color Matching Priority under [ In Quality > Manual Color Settings > Color
Settings > Matching > Application Color Maching Priority] is cleared, it can declare to the application software
on PC that Driver handles ICM processing.
This notice enables to perform Image Color Matching processing as designated in printer driver UI since the
process is not done to the color values given from OS to driver.
Though Application Color Matching Priority is set to on as default so that existing version can be compatible,
when specified color tinge cannot be materialized, clearing the checkbox makes it manageable.
F-2-13
Color
F-2-14
2-10
Chapter 2
If [Use Skip Blank Pages Mode] is set to [On], blank pages are skipped even if [2-sided Printing] is set in [Print
Style].
For instance, when the first page is blank and the second and third pages have data, the first page is skipped, the
data of second page is printed on the front side of the sheet, and that of third page is printed on the back side of
the same sheet.
Similarly, when the first page has data, the second is blank and the third has data, the data of first page is printed
on the front side of the sheet, the second page is skipped, and the data of third page is printed on the back side
of the same sheet.
Though the setting of [Skip Blank Pages] is conducted on the control panel of the iR main body, a printer driver
released enables users to specify the setting in the driver.
[Finishing] - [Finishing Details]
F-2-15
2-11
Chapter 2
A feature to transfer files from host PC terminals to the printer and interrupts the data to print without a printer
driver. The printer interprets and prints the files. It, thus, saves opening files for printing.
To print, specify a PDF, TIFF, or JPEG file through the Remote UI.
The Direct Print feature includes printing with LPR commands through the command prompt.
Direct Print for TIFF and JPEG Files
The Direct Print is designed to use in the conditions below. It does not guarantee operations other than those
specified.
Direct Print:
The automatic emulation judge judges a print job of JPEG or TIFF data sent directly from a host as a direct print
data and the Direct Print interprets and prints the job.
-Sending through the command prompt with a command such as "copy /b" and "lpr."
Use LPD for the method to forward the PDF file from a host PC to the device and forward a job to be printed.
Use LPR command as a method to forward a job. Job using LPD cannot specify various print settings.
Data Processing:
The Direct Print interprets data without saving in the hard disk drive. - Sequential method.
The compatible and incompatible coding schemes for JPEG data are shown below.
2-12
Chapter 2
The PDF Direct Print is a function to forward the PDF file from host PC terminal to the printer, and for the
printer to interpret and to print the PDF file. Therefore, the client software that corresponds to the printer driver
doesn't exist. Moreover, neither the transmission media nor the protocol to forward the file to the printer are
specified. In this machine, used remote UI and LPR as client software to forward the PDF file to the printer.
Direct Print is that a file is forwarded to the printer directly, In contrast, Reference Print is that file's location
information is forwarded to the printer and the printer obtains and print the file. In this machine, the Reference
Print function of the PDF directed from the remote UI is provided.
HostPC HostPC
Web Server
F-2-16
Using reference printing, you can specify the URL of a PDF file existing in an external device, and download
the file to your device for printing. You must use a remote UI whenever you wish to introduce a reference print
job.
HTTP is the only protocol that is supported.
Downloading is possible from the Internet through a proxy server. (The proxy server must be set up using user
mode/network settings.)
Authentication is possible by means of a user name and a password; however, authentication will not take place
unless the Web server is capable of authentication in keeping with the HTTP protocol. Also, a user name and a
password must be entered in advance, and there will be no interactive authentication procedure.
There must be no more than one URL.
A job is introduced by specifying an URL in the URL input field on the PDF direct print setup page and then
pressing the Print button.
Both a PDF direct print job and a reference print job may be introduced at the same time. A reference print job
may be introduced even while a PDF file is being transferred for PDF direct printing.
2-13
Chapter 2
An error identified before downloading of a PDF file is started will be indicated using the remote UI that has
been used to introduce the reference print job. The types of errors that may be indicated are as follows:
-an error caused by not being able to find the specified server
-an error caused by not being able to find the specified PDF file on the Web server
-URL structured error
-authentication error
-connection time-out
-an error caused by the absence of a PDF file in the specified URL
When the presence of the file has been confirmed and downloading has been started, an indication to that effect
will also be made.
An additional job (PDF reference print) will not be accepted until the PDF file in question has been downloaded
from the specified URL, indicating an error using the remote UI if an attempt is made.
While a PDF file is being downloaded, an indication is made as part of spool job status; a time-out condition
occurring at time of downloading will be indicated as "NG" in the spool job history.
Regardless of whether hard disk spooling is enabled or disabled, reference printing will always be through
spooling on the hard disk.
A press on the Stop button in the browser immediately after the introduction of a reference print job using the
remote UI will not stop the ongoing PDF downloading if the HTTP command has already been sent to the device
and PDF downloading has started. (If the wrong URL has been entered and a reference print job has been
introduced, another job will not be accepted until a time-out condition has occurred for connection to the Web
server.)
2.1.14 IPPS Print
0016-1297
There is a security risk in the current IPP (Internet Printing Protocol), as the print data to be sent on the Internet
is not encrypted. In IPPS, the data is encrypted by SSL (Secure Sockets Layer) and the reliability is enhanced.
Supported OS:
Windows 2000/XP/Windows2003 Server
Restrictions
It is impossible to use IPPS and IPP together.
When System Settings > Network Settings > TCP/IP Settings > IP Address Range Settings in Additional
Functions is set to 'ON', printing is available only from the PC with valid address.
How to setup:
In Additional Function, enter System Settings > Network Settings > TCP/IP Settings > IPP Print Settings and
set 'Use SSL' to 'ON'.
F-2-17
2-14
Chapter 2
F-2-18
2-15
Chapter 3
INSTALLATION
Contents
Contents
3.1 Installation procedure ........................................................................................... 3-1
3.1.1 Overview of the Installation Procedure .........................................................................3-1
Chapter 3
As a rule, the user is expected to obtain a license key and register it to the device. Detailed instructions are found
in the User's Guide. The following is an outline of the instructions:
1. Using the following URL, access the LMS, and obtain the license key by following the instructions shown
on the screen:
http://www.canon.com/lms/license/
Memo:
A license key is issued in exchange for the 16-digit number indicated on the License Access Number
Certificate and the serial number of the device (e.g., ABC01234) to which the license will be registered. The
device serial number will be indicated in response to a press on the Counter key on the iR device (under
[Serial Number]).
2. Copy the 24-digit number shown on the Web browser screen in the space given for the purpose on the License
Access Number Certificate sheet.
Caution:
Be sure to double-check the number to avoid an error. Be sure that the user is aware of the importance of the
License Access Number Certificate and that it must be stored away in a safe place.
3. Make the following selections: user mode>system control setup>license control. Then, type in the 16-digit
number, and click [Execute]. In response, the license key will be registered and the appropriate functions will
be enabled. Otherwise, any of the following error messages will appear:
"The number of the license key is not correct. Check the license key."
>> Make sure that the license key is not issued for a different device.
>> Make sure that the number has been correctly typed in.
>> Make sure that the license key is the correct one.
4. Hold down the control panel power switch for 3 sec or more. Follow the instructions shown on the screen for
shut-down sequence so that the main power switch may be turned off. Turn off the main power switch, wait for
10 sec, and turn it back on.
5. The registered license will become valid when the device is turned back on. When it has started normally,
press the Counter key, and click the Device Configuration button to make sure that the Kit is indicated as part
of the options.
3-1
Chapter 4
MAINTENANCE
Contents
Contents
4.1 Notes when service........................................................................................... 4-1
4.1.1 Points to Note ........................................................................................................... 4-1
4.2 Reference matter in market service ............................................................... 4-1
4.2.1 Invalidating the License for Transfer to a Different Device data recovery method
4-1
4.3 Related Error code............................................................................................ 4-2
4.3.1 #853 ............................................................................................................................. 4-2
4.3.2 Imaging(error) ............................................................................................................. 4-3
4.3.3 PDF error message(Direct Print) ............................................................................. 4-4
4.4 Related Service Mode ...................................................................................... 4-6
4.4.1 Invalidating the License for Transfer to a Different Device (Level 2)................. 4-6
Chapter 4
When performing service on this kit in the field, note the following cautions and reference items.
- With regard to paper size and margin size, depending on calculation errors in the system,application software
and driver, or due to the paper feed accuracy of the printer, paper shrinkage or stretching caused by heat and
or humidity, the actual sizes may be greater or smaller than the specified or desired size.
- Supported fonts can be used by adding to the Windows fonts.
Here the keys required to invalidate the license for transfer to a different device will be described. The following
is not an explanation of how to validate such license.
'Invalidating the License for Transfer to a Different Device' can be executed in the Service Mode in order to
make accessories validated by the license information available to another host machine.
License history data is required when invalidating the license for transfer to a different device. License history
data is stored threefold in 3 different locations - HDD, Counter PCB, and SRAM on the Main Controller.
Once the HDD and / or Main Controller are replaced with new ones, it may not be possible to invalidate the
license for transfer to a different device for options validated by the license information.
License key history data
License history data is used in order that the transferred license key cannot be used in the same iR host
machine again.
-License history data has a total of the number of the iR accessory license key and the MEAP applications
and only 30 of the total are doubly stored in HDD and the counter board.
-Only 30 of the total are doubly stored. The rest is stored in HDD only.
When HDD is broken
If turning on the power of the iR host machine after the replacement of HDD, max. 30 items of license key/
transferred license key history data are automatically recovered in HDD from the license key history data on the
counter board.
Lost license key history, which has been stored only in HDD, becomes as follows:
-The transfer license key cannot be issued to unrecoverable license key history.
-The transfer license key for unrecoverable license key history of the license key that the transfer license key
has been issued is not displayed in service mode.
4-1
Chapter 4
Some jobs entered by the iR host machine may be cancelled even if the printing instruction is given to the iR
host machine from the PC.
If you check the error code in the following operations, you can obtain the reference information which can
specify the cause.
Press 'System state/Stop' button on the lower right of the control panel to display the job history.
Select a job that resulted in NG, press 'Further information' button, then the error code is displayed in the space
of Result.
The error code "#853" (An error or non-support function is detected in the host machine and the job is canceled)
has 30 or more causes. It has been difficult to specify the cause, as 30 or more causes are lumped together as
#853.
The details of the cause of Job cancel are shown in the list below.
First, codes: #xxx shown in the attachment list, are allocated to the causes that are lumped together as #853 in
Job history on the UI screen.
Select FUNCTION > MISC-P > PJH-P-1/2, then detailed codes in the list below are displayed.
T-4-1
4-2
Chapter 4
A detailed history report is output so that users can check the internal (CPCA job log) detailed cause in service
mode, since detailed causes are grouped to some extent on the UI display. But, this report shows only PDL print
job.
FUNCTION > MISC-P > PJH-P-1 (Latest 100 jobs)
FUNCTION > MISC-P > PJH-P-2 (Max. 5,000 jobs)
4.3.2 Imaging(error)
0015-3477
When an error is detected in TIFF or JPEG image except PDF while the direct print function works, it conducts
error processing.
Following errors are detected during direct print processing.
-Initialization error
-Work Memory full
-Invalid data
-Processing error
Initialization error
This error occurs when specified memory cannot be allocated at the startup of direct print function. When
initialization error is detected, the function prints pages that have already been rendered and executes the
following processing.
-Regardless of [Warning display] setting in IMAGING set up menu, it displays an error message on the panel
and moves to error state.
After moving to the error state, turning the power on/off by user operation is the only way to return the
function to the normal operating state.
Work Memory full
This error occurs when necessary memory for imaging process is exhausted. When memory full error is
detected, the function prints pages that have already been rendered and executes the following processing.
-Regardless of [Warning display] setting in IMAGING set up menu, it displays an error message on the panel
and moves to error state.
After moving to the error state, if the job is canceled by user operation, it returns to normal, skips importing
the remaining data, and ends.
Invalid data
This error occurs when invalid data, which is impossible to be analyzed, is detected during data analysis of
JPEG or TIFF. When the direct print function detects invalid data, it prints pages that have already been
rendered and executes either of the followings. After that, if it is possible to continue the processing, printing
job of the remaining data is done. If it is impossible to continue the processing, it skips importing the
remaining data in printing job and ends.
-If [Warning display] is set to 'ON', it displays an error message and moves to error state. After that, if the
job is cancelled by user operation, it returns to normal.
-If [Warning display] is set to 'OFF', it does neither display any message nor move to error state.
Processing error
This error occurs when something abnormal is detected while the direct printing function works. For
example, an error that occurs when the function is importing data from receiving buffer, or an error that
occurs when the function is accessing to hard disk. When this translator detects a processing error, it prints
pages that have already been rendered and executes the following.
-Regardless of [Warning display] setting in IMAGING set up menu, it displays an error message on the panel
and moves to error state.
After that, if the job is canceled by user operation, it returns to normal, skips importing the remaining data,
and ends.
4-3
Chapter 4
T-4-2
4-4
Chapter 4
4-5
Chapter 4
Service Mode Item Used to Invalidate a License for Transfer to a Different Device (Level 2)
Possible Situation
A license may be used on a different device through transfer, as when replacing the device at the end of a lease
agreement. To do so, the user must first invalidate the existing license by performing a set of steps referred to
as "invalidation of a license" using service mode. At times, both source and target of transfer may be the same
device, and a license therefore may also be invalidated only temporarily. It is important to note that the user must
contact the Sales Company to make a license good regardless of whether it has been invalidated intentionally or
inadvertently.
Invalidation Procedure
Invalidation consists in invalidating the license in service mode and generating an invalidation certificate that
proves the completion of invalidation. Invalidation may take place for individual optional functions, and a
specific function becomes no longer available as soon as an invalidation certificate is issued. The user contacts
the Sales Company and provides the following: the invalidation certificate, the device serial number of the
source of transfer, the device serial number of the target of transfer, reason of transfer. In response, the Sales
Company may issue a license key for new installation on a different device. The user must take note of the new
license key in writing, and keep it as a record after registering it to the target device.
Installation Procedure
1. Start service mode, and activate Level 2 so that the following is true:
COPIER>OPTION>LCNS-TR
The following screen appears, showing the current status of various options:
F-4-1
4-6
Chapter 4
Screen Design:
SET-xxxx: indicates the license status. If installed, the option is identified as '1' under A.
To invalidate an option for transfer, select it, and type in '0' under B; then, click [OK] so that the option will
be invalidated and an invalidation certificate will be issued.
TR-xxxx: indicates any invalidation certificates that have been generated under C.
Memo:
Not all foregoing options are available in all countries and regions.
T-4-3
SEND Send
ENPDF Encrypted PDF
SPDF PDF(OCR)
EXPDF Encrypted PDF + PDF(OCR)
PDFDR PDF Direct Print
SCR Encrypted Printing Software
HDCLR HDD Data Encryption + HDD Date Erase Kit
BRDIM BarDIMM(PCL Optin)
VNC Remote Operator's Software Kit
WEB Web Access Software
HRPDF PDF(Compact)
TRSEND Universal Send Trial Kit
WTWRK Secure Watermark
TSPDF Time Stamp PDF(Japan Only)
USPDF Digital User Signature PDF Kit
DVPDF Device Signature PDF
SCPDF Trace&Smooth
AMS Access Management System Kit
ERDS Embeded RDS
PS PS
PCL PCL
PSLI5 No use for LMS
LIPS5 No use for LMS
LIPS4 LIPS V(Japan Only)
PSPCL PS + PCL
PCLUF PCL + UFR II
PSLIP LIPS V/PS(Japan Only)
PSPCU PS + PCL + UFR II
LXUFR UFR II
4-7
Chapter 4
2. If an option has already been installed, '1' will be indicated under A. If you want to invalidate it, select it, and
type in '0' so that the indication under B will change to '0'.
3. Thereafter, when [OK] is pressed, the indication under A will change to '0' and, at the same time, an
invalidation certificate will be indicated in the form of a number. Take note of it in writing together with the
serial number of the target device.
5. Contact the Sales Company, and provide the following: invalidation certificate for transfer, serial number of
the source device, serial number of the target device. The Sales Company, in response, may issue a new license
key that may be registered on the target device.
6. Register the new license key to the target device, and check to make sure that the function has been enabled.
4-8