Académique Documents
Professionnel Documents
Culture Documents
1 rev1
Design envelope split coupled vertical in line pump with parallel sensorless controller
Model: Series Design Envelope Sensorless 4300 0810-050.0
0
0 0.5 1 1.5 2 2.5 3
Water, spgr= 1.0000 Flow ( 1,000 usgpm)
Weight: 725 lb
• Not to scale
• R = minimum lifting clearance required above motor
• Units of measure : inches [millimeters]
• Coupling guard and flush line (not shown) are supplied
• Tolerance of ± 0.125 inch (± 3 mm) should be used
• For certified dimensions, please contact your Armstrong representative
• Pump equipped with casing drain plug and ¼ inch NPT suction and discharge gauge ports
Special instructions
Selected options
Motor 60 Hertz (380 volts)
Casing Wear Ring - Not included
Environmental Application: Indoors
Parallel Sensorless BMS Comm Protocol: Standard (no card)
PSPC Controller Model: PSPC-N
PSPC Controller Part Number: 710000-000
Additional equipment
Flotrex: FTV-8FA (570200-481)
Suction Guide: SG-88 (516860-028)
Materials of construction
Construction: BF Impeller: Bronze (B584-844)
Rating: ANSI-125 Pump shaft: SS ASTM A276 Type 416
Connections: Inlet: 12 in, Outlet: 12 in Flush line: Braided Stainless Steel
Casing (volute): Cast Iron (A48-30) Casing gasket: Confined Non-Asbestos Fiber
Weight: 2550 lb
• Not to scale
• R = minimum lifting clearance required above motor
• Units of measure : inches [millimeters]
• Coupling guard and flush line (not shown) are supplied
• Tolerance of ± 0.125 inch (± 3 mm) should be used
• For certified dimensions, please contact your Armstrong representative
• Pump equipped with casing drain plug and ¼ inch NPT suction and discharge gauge ports
Connection details
Connection Size Rating OD Bolt quantity* BCD Bolt size
Inlet 12 ANSI-125 19 12 17 0.875
Outlet 12 ANSI-125 19 12 17 0.875
*Equally spaced straddling centreline
Special instructions
Selected options
Motor 60 Hertz (380 volts)
Casing Wear Ring - Bronze CWR
Additional equipment
Flotrex: FTV-10FA (570200-482)
Materials of construction
Construction: BF Impeller: Bronze (B584-844)
Rating: ANSI-125 Pump shaft: SS ASTM A276 Type 416
Connections: Inlet: 6 in, Outlet: 6 in Flush line: Braided Stainless Steel
Casing (volute): Cast Iron (A48-30) Casing gasket: Confined Non-Asbestos Fiber
0
0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6
Weight: 913 lb
• Not to scale
• R = minimum lifting clearance required above motor
• Units of measure : inches [millimeters]
• Coupling guard and flush line (not shown) are supplied
• Tolerance of ± 0.125 inch (± 3 mm) should be used
• For certified dimensions, please contact your Armstrong representative
• Pump equipped with casing drain plug and ¼ inch NPT suction and discharge gauge ports
Connection details
Connection Size Rating OD Bolt quantity* BCD Bolt size
Inlet 6 ANSI-125 11 8 9.5 0.75
Outlet 6 ANSI-125 11 8 9.5 0.75
*Equally spaced straddling centreline
Special instructions
Selected options
Motor 60 Hertz (380 volts)
Casing Wear Ring - Not included
Additional equipment
Flotrex: FTV-6FA (570200-480)
Flo-trex valve
Model: FTV-F (2.5 to 12 inch)
Materials of construction
FTV-8FA-Flo-Trex Valve-ANSI-125-Angle Flanged FTV-Flanged-2.5-12
Body: Cast Iron ASTM A48 Class 30 Spring: Stainless Steel ASTM A313 Type 302
Disc: Bronze ASTM B584-C84400 O rings: BUNA (STEM) Elastomers & EPDM
Seat: EPDM 2 metering ports: Brass Body with EPDM Check and
Gasketed Cap
Stem: Stainless Steel ASTM A582 Type 416 2 drain tappings: ¼" NPT with Brass Plug
Not to scale
Units of measure: inches [millimeters]
Tolerance of +/- 0.125 inch (+/- 3 mm) should be used
For certified dimensions, please contact your Armstrong representative
Suction guide
Model: SG (2 to 12 inches)
Materials of construction
SG-88
Body: Cast Iron Cover gasket: Synthetic fiber
Guide vanes: Cast Iron Strainer: Stainless Steel,0.125"(3mm)Perf.
Cover plate: Cast Iron Start-up strainer*: Fine Mesh Galvanized Steel
Not to scale
Units of measure: inches [millimeters]
Tolerance of +/- 0.125 inch (+/- 3 mm) should be used
For certified dimensions, please contact your Armstrong representative