Vous êtes sur la page 1sur 11

www.osram.

com/flex

LINEARlight Colormix Flex Protect

LINEARlight Colormix Flex

LINEARlight Colormix Flex and 05/2015

LINEARlight Colormix Flex Protect


Quick installation guide

Light is OSRAM
LINEARlight Colormix Flex and LINEARlight Colormix Flex Protect | Quick installation guide

1 Installation
1.1 Precautionary measures
Before the installation of LINEARlight Colormix Flex and Mechanical forces
LINEARlight Colormix Flex Protect modules, the following Avoid mechanical forces (F) on the connector (feeder) and
precautions should always be observed: the LEDs. Try to connect the connector as the last step of
the installation. A strain relief is recommended. In addition,
ESD mechanical stress must not be applied to the module itself
Be aware that the products can be damaged by electro- (e.g. no twisting or bending in excess of the allowed radius).
static discharge (ESD). Earthing is a very effective measure
to avoid the damaging effects of electrostatic discharge.
Therefore, a personal earthing system (ESD field kit) should F
be used during mounting to prevent the build-up of static
charge.

3
Cleaning
Depending on the surface, use a multi-purpose cleaner (e.g.
isopropyl alcohol) to provide a clean and dry mounting sur-
face which is free of oils, release coatings and dirt particles.

LF06A-P
Cutting
Ensure that the modules are cut properly at an angle of 90°
before attaching the connector.

LINEARlight Colormix Flex 90° 90°


90°

LINEARlight Colormix Flex 90°


Protect

2
LF06P2-P
LINEARlight Colormix Flex and LINEARlight Colormix Flex Protect  |  Quick installation guide

2 Products and tools

01 06
01
06 05

02
04
05
03 03

04

02
08
07

07 08

LINEARlight Colormix Flex (ADVANCED) LINEARlight Colormix Flex Protect (ADVANCED)


(see figures above) (see figures above)

No. Product reference Product number (EAN) No. Product reference Product number (EAN)
01 LF05CA2-RGB3 4008321851536 01 LF05CA-RGB3-P 4008321977205
02 LF-4PIN Flex SC 4052899904835 02 LF-4PIN Protect 4008321977076
03 LF-CONN Flex SC 4008321832467 03 LF-4CONN PROTECT 4008321977090
04 LF-WIRE-30 FLEX SC 4008321875587 04 LF-ENDCAP Protect 4008321977106
05 LF-WIRE-150 FLEX SC 4008321875563 05 OT EASY 80 4008321808363
06 OT EASY 80 4008321808363 06 Silicone glue –
07 Scissors – 07 Cutter –
08
LF05CA Screwdriver – 08 Screwdriver –
LF05CA-P
2,2 mm

24V Tc LF05CA-RGB3-P 27R-P n007H 24V Tc InQbl.745kaA4 made in italy A 123 456 78 90

12,7 mm

10 20 mm (4x) 100 mm 25 mm

11 mm
8 mm

100 mm 100 mm 20 mm
4000 mm 4000 mm

LF05CE
LF05CE-P
2,2 mm

24V Tc LF05CE-RGB1-P 27R-P n007H 24V Tc InQbl.745kaA4 made in italy A 123 456 78 90

12,7 mm
LINEARlight Colormix Flex (ECO) LINEARlight Colormix Flex Protect (ECO)
15 30 mm (4x) 150 mm 25 mm
LF05CA
Product reference Product number (EAN)
11 mm

Product reference Product number (EAN)


8 mm

LF05CA-P
2,2 mm

LF05CE-RGB1 4008321593375 LF05CE-RGB1-P


24V LF05CA-RGB3-P 27R-P
Tc n007H 24V Tc InQbl.745kaA4 4008321977182
made in italy A 123 456 78 90
150 mm 150 mm 30 mm
LF-4PIN 6000 mm
4008321514585 LF-4PIN Protect 4008321977076
12,7 mm 6000 mm
LF-CONN-10
10 20 mm (4x) FLEX 4008321955333 LF-4CONN PROTECT 4008321977090
100 mm 25 mm
LF-CONN-150 FLEX 4008321955340 LF-ENDCAP Protect 4008321977106
8 mm

11 mm

OT EASY 80 4008321808363 OT EASY 80 4008321808363


100 mm
Scissors – Silicone glue 100 mm – 20 mm
4000 mm
Screwdriver – Cutter 4000 mm –
LF05CE Screwdriver –
LF05CE-P
2,2 mm

24V Tc LF05CE-RGB1-P 27R-P n007H 24V Tc InQbl.745kaA4 made in italy A 123 456 78 90

12,7 mm
15 30 mm (4x)
150 mm 25 mm
8 mm

11 mm

150 mm
6000 mm 150 mm 30 mm
6000 mm

3
LINEARlight Colormix Flex and LINEARlight Colormix Flex Protect | Quick installation guide

3 LINEARlight Colormix Flex

3.1 Assembly
The following images show a LINEARlight Colormix Flex
ADVANCED module. The instruction steps, however, also
apply to a LINEARlight Colormix Flex ECO module.

3.1.1 Connection to the LED driver

Figure 1 Step 1
Observe the polarity of the module and the wires,
chronologically:

— Connect the red wire to “R“.


— Connect the green wire to “G“.
— Connect the blue wire to “B“.
— Connect the black wire to “+24 V“.

R
G
B
+

Figure 2 Step 2
Peel off the release liner from the adhesive tape at the
connecting area.

Figure 3 Step 3
Make sure that the connector is in the right position (see
small picture) and not upside down. Then slide the module
into the connector.

4
LINEARlight Colormix Flex and LINEARlight Colormix Flex Protect | Quick installation guide

Figure 4 Step 4
Place the connector on an even surface and press the top
side until you hear two “clicks” (one “click” on each side of
the connector).
k "
"clic

"click"

Figure 5 Step 5
Peel off the remaining release liner from the tape to mount
the LED module.

Figure 6 Step 6
Observe the polarity on the LED driver side as well:

— Connect the black wire to “24 V (+)“.


— Connect the red wire to “CH1 (R-)“.
— Connect the green wire to “CH2 (G-)“.
— Connect the blue wire to “CH3 (B-)“.

3.1.2 Board-to-board connection

Figure 7 Step 1
Insert both PCBs into the LF-CONN Flex SC. Make sure
that the connector is not upside down.

5
LINEARlight Colormix Flex and LINEARlight Colormix Flex Protect | Quick installation guide

Figure 8 Step 2
Place the connector on an even surface and press the top
side until you hear two “clicks” (one “click” on each side of
" the connector).
k
"clic

"click"

3.1.3 Going around corners

Figure 9 Step 1
For installations around corners, you can use the flat wires
LF-WIRE-30 FLEX SC and LF-WIRE-150 FLEX SC in combi-
nation with two LF-CONN Flex SC.

Figure 10 Step 2
Place the connectors on an even surface and press each
of the top sides until you hear two “clicks” (one “click” on
each side of the connector).
k "
"clic

"click"

Figure 11 Step 3
The flat wires may be used as an extension or a
solution to go around corners.

6
LINEARlight Colormix Flex and LINEARlight Colormix Flex Protect | Quick installation guide

4 LINEARlight Colormix Flex Protect

4.1 Assembly
The following images show a LINEARlight Colormix Flex Notes:
Protect Advanced module. The instruction steps, however, — The minimum bending radius is 5 cm.
also apply to a LINEARlight Colormix Protect ECO module. — Pay attention to avoid highly corrosive atmospheres, e.g.
permanent high humidity or hydrogen sulfide (H2S). In
case of current LED technology, H2S causes accelerated
corrosion leading to a shortened lifetime or premature
failure. Sources for H2S may be rubber, foamed rubber,
soft-foam tapes, sealings on rubber basis, natural sources
(e.g. sulfur springs) etc. To avoid H2S from sulfur-vulcan-
ized rubber, it is necessary to switch to silicone-based
materials or rubber that is peroxide-cross-linked. Indica-
tion may be found in the material datasheet of the rubber
supplier.

4.1.1 Connection to the LED driver

Figure 12 Step 1
To ensure the correct polarity, please observe the following
when connecting the LED module (shown on the right) to the
connector (shown on the left): The cable of the connector
and the LEDs on the module must both be facing upwards
(as shown in Figure 12).

Figure 13 Step 2
Peel off the release liner from the adhesive tape at the
connecting area.

7
LINEARlight Colormix Flex and LINEARlight Colormix Flex Protect | Quick installation guide

Figure 14 Step 3
Make sure that the connector is in the right position. Then
slide the LED module into the connector. Ensure that the
module is completely inserted, without applying too much
pressure.

Figure 15 Step 4
Place the connector on an even surface and press the top
side until you hear two “clicks” (one “click” on each side of
the connector).

"click"

"click"

Figure 16 Step 5
Peel off the remaining release liner from the tape to mount
the LED module.

Figure 17 Step 6
Observe the polarity on the LED driver side as well:

— Connect the black wire to “24 V (+)“.


— Connect the red wire to “CH1 (R-)“.
— Connect the green wire to “CH2 (G-)“.
— Connect the blue wire to “CH3 (B-)“.

8
LINEARlight Colormix Flex and LINEARlight Colormix Flex Protect | Quick installation guide

4.1.2 Board-to-board connection with connector

Figure 18 Step 1
Insert both PCBs into the LF-CONN Protect. Make sure
that the corrector is not upside down.

Figure 18

Figure 19 Step 2
Place the connector on an even surface and press the top
side until you hear two “clicks” (one “click” on each side of
"click" the connector).

"click"

9
LINEARlight Colormix Flex and LINEARlight Colormix Flex Protect | Quick installation guide

4.1.3 End cap mounting

Figure 20 Step 1
Peel off the release liner from the adhesive tape at the end
of the LED module.

Figure 21 Step 2
Put a drop of silicone glue into the end cap.

Figure 21 Step 3
Slip the end cap over the end of the LED module.

10
www.osram.com/flex

05/15 OSRAM LLS SMK OEM Subject to change without notice. Errors and omissions excepted.

OSRAM GmbH

Head office:

Marcel-Breuer-Strasse 6
80807 Munich, Germany
Phone +49 89 6213-0
Fax +49 89 6213-2020
www.osram.com

Vous aimerez peut-être aussi