Académique Documents
Professionnel Documents
Culture Documents
Physical dimension.........................................................................................2
Printer features..............................................................................................2
RP-100-300II
Printer specification.......................................................................................2
Drive installation........................................................................................4
Hexadecimal mode...................................................................................6
Start DHCPfunction.............................................................................6
Buttons.....................................................................................................14
Buzzer...................................................................................................15
Interface..................................................................................................13
DIP switch....................................................................................................14
Cutter maintenance....................................................................................15
1
Greek/Hebrew/East
Europe/Iran/WPC1252/PC866/PC852/
1. Printer Physical dimension:
PC858/IranII/Latvian/Arabic/PT151,1251/PC73
LxWxH:180x139x127mm; 7/WPC/
Weight:1.23kg; 1257/Thai
Vietnam/PC864/PC1001/(Latvian)/(PC1001)/
2. Features: (PT151,1251)/(WPC1257)/(PC864)/(Vietnam)/(
300mm/sec high print speed; Thai)
UPC-A/UPC-E/JAN13(EAN13)/JAN8(EAN8)C
Low power consumption:1.44w(Min.);
Barcode mode ODE39/ITF/
Multiple interface: Serial, USB, Ethernet port CODABAR/CODE93/CODE128/QRCODE
2 3
4. Driver installation
1).Insert the driver CD disk, run the Partner 80Driver to set up
5) Completed.
4 5
5. Print self-test page 8. LAN port connection setting
A. Turn off the printer. A. Connect printer to PC via LAN cable.
B. Make sure the paper roll is installed correctly and the printer top cover is Please make sure PC’s IP should be on the same network segment with the
closed. printer’s IP .
C. Press and hold on the FEED button and turn on the printer. When the red For example: Printer default IP address:192.168.123.100. So PC’s IP address
indicator is OFF, then release the FEED button. printer will print out a page. should be set 192.168.123.* network segment, but can not the same as the
printer IP, otherwise printer will not be connected with the PC.
6. Hexadecimal mode
A. Turn off the printer.
B. Make sure the paper roll is installed correctly and the printer top cover is
closed.
C. Press and hold on the FEED button and turn on the printer. After 10
seconds, please release the FEED button, then printer will be entered
the Hexadecimal mode.
6 7
1) With Windows software utility tool.
8 9
2) Create a new port
10 11
10. Baud rate setting
Using serial port to print, printer serial baud rate must be same as the PC
serial port baud rate, otherwise the printer won’t work. The setting
method is as follows:
A. Printer Baud rate :Set the DIP switch on the bottom of the printer
(SW7 , SW8Combination).
DIP SWITCH
12 13
11. Buttons
1) Feed Button:A. Paper feed B. Print self-test page C. enter
Hexadecimal mode
2) Power indicator (Blue): When the power indicator is ON, Printer is
powered on.
3) Error indicator (Red): A. flashing slowly 2 time: Cutter error B.
Flash fast: Printer overhead protection is activated C. Error
indicator is ON: Paper shortage;
4) Paper shortage indicator (Red): Paper shortage indicator lights: Paper
sensor error or close cover sensor error or Paper shortage
12. Buzzer
1) When cutter error occurred, buzzer will sound short beep 2 times,
and then follow by a long beep 1 time.
2) When paper shortage or cover is not closed, buzzer will sound
continuously short beep sound.
3) When printer resumes printing from un-printed data in buffer
memory, buzzer will quickly sound 4 times after receipt printed.
13. Interface
USB 2.0
100M Ethernet Pin2/pin5Ca DC24V power
RS232 sh drawer
Serial port
14 15
14. DIP Switch
1 2 3 4 5 6 7 8
Sele Cutter
SELECT Two-byte
ct Select Character with Select
PRINT character
cutt beeper per line cash baudrate
DENSITY code
er drawer
42-font A
ON OFF ON Dark ON Yes
/56-font B Turn the gear to
48-font A reset the cutter
OFF ON OFF Light OFF No
/64-font B Open cover by the
arrow direction
15. Auto Cutter Maintenance
Improper usage and/or bad quality thermal paper may cause the cutter jam
(stuck), thus printer cover is unable to open. Caution: Do not open the printer cover by force, doing so will result in
In this case, you may power cycle the power button (turn off and turn back on
after 3 seconds) and check if the auto cutter has recover itself from cutter jam damaging the print head and auto cutter.
by trying to open the printer lid.
If print lid still can’t be opened, please follow below manual method to
restore the cutter back into position. 1st: Open the printer front cover, and
then start to turn the gear until the cutter knife has returned fully. Once it has
cutter knife has returned fully, you can open the printer lid.
16 17