Académique Documents
Professionnel Documents
Culture Documents
(a) Tensile strength (b) Hardness (c) Fatique strength (d) (a) and (b) both
(a) Hart Ford (b) W.C.Rontgen (c) Dr.H.H.Lester (d) Dr.Eimer Sperry
(a) Hart Ford (b) W.C.Rontgen (c) Dr.H.H.Lester (d) Dr.Eimer Sperry
(a) Ultrasonic Testing (b) Radiographic Testing (c) Magnetic Particle Testing
(a) Photoelectric (b) piezo electric effect (c) radio active decay (d) skin effect
10) Which one is an inherent discontinuity
(a) Transducer (b) Telescope (c) Binocular (d) None of the above
14) The method involved use of an oil usually made of a dark lubrication oil diluted with to
find surface defects
(a) Zyglo test (b) hammer test (c) oil and whitening test (d) A and C only
15) Inspection technique which must take place prior to during after welding
(a) Liquid penetrating test (b) ultrasonic testing (c) radio graphic testing (d)
visual inspection
10. Total time in which penetrant is in direct contact with test specimen
(a) soak time (b) baking time (c) dwell time (d) immersion time
11. Most effective NDT method for locating defects in ferromagnetic material
(a) Ultrasonic testing (b) magnetic particle testing (c) liquid penetrant testing
(d) radio graphic testing
14. Magnetic field applied to reduce the magnetic flux of magnetic material to zero is called
(a) permeability (b) residual magnetism (c) retentivity
(d) coercive force
1. Inductance is caused by
(a) Direct current (b) Resistance in the coil (c) Interaction of changing magnetic field
material with conductor (d) material
7. Which type of probe is used to inspect the inside diameter of the bore?
(a) Pencil probes (b) Pancake probes (c) Bobbin probes (d) bolt Hole probes
Thermography
4. ECT Means
(a) Electrochemical therapy
(b) Electro convulsive therapy
(c) Electro-conductive therapy
(d) Electro-magnet therapy
5. Heat Ray Means
(a) Characteristic of Heating an object
(b) Characteristic of heated affected zone
(c) Characteristic of an deflection zone
(d) Characteristic of a wavelength visible light.
6. The most commonly used band for commercial Infrared imaging Range is
(a) 0.75-15 µm (b) 6-15 µm (c) 3-6 µm (d) 0.75-3 µm
10. Which code & Standard is for minimum resolvable temperature difference for thermal
Imaging System?
(a) ASTM E 1311 (b) ASTM E 1213 (c) ASTM E 1543 (d) ASTM E 1653
11. Which code & Standard is for minimum detectable temperature difference for thermal
Imaging System?
(a) ASTM E 1311 (b) ASTM E 1213 (c) ASTM E 1543 (d) ASTM E 1653
12. Which code & Standard is for Noise Equivalent temperature difference for thermal
Imaging System?
(a) ASTM E 1311 (b) ASTM E 1213 (c) ASTM E 1543 (d) ASTM E 1653
Acoustic Emission
4. SWF Means
(a) Stress wave factor
(b) Strain wave factor
(c) Suitable wave length frequency
(d) Stress wise frequency
Unit V Radiography
11. Which of the following types of intensifying screens are not used in industrial
radiography?
(a) Lead (b) Fluorescent (c) Silver Halide (d) All of the above
(a) Milliamperage
15. The focal spot size of an X ray Machine must be known in order to determine:
17. A term which refers to the sharpness of the radiographic image is:
(a) Sensitivity
(d) Definition
18. Of the following radiographic sources, which emits the most penetrating radiation?
(a) Density (b) Processing (c) Radiation energy (d) All of the above
(a) 74 days (b) 129 days (c) 5.3 years (d) 30.1 Years
21. Poor contact between lead screens and film is likely to cause:
23. A depression at the edge of a weld where the base metal has been melted during welding is
called:
(a) Burn through (b) Undercut (c) Root concavity (d) Root convexity
24. Which of the following welding discontinuities would be considered the most serious?
(a) Porosity (b) Incomplete penetration (c) Crack (d) Slag inclusions