Académique Documents
Professionnel Documents
Culture Documents
Edition 26/08/2010
Identification no:
02 05 01 01 015 0 000008
Sikaflex® AT-Façade
Sikaflex® AT-Façade
High performance movement joint sealant
Product Sikaflex® AT-Façade is a 1-part, moisture curing elastic sealant based on Silane
Terminated Polymers. Especially for movement and connection joints on porous
Construction
Tests
Approval / Standard DIN 18540 F, SKZ Würzburg
ISO 11600 Group F, class 25LM
SNJF
ASTM C920
Product Data
Form
Colours Grey, white
Packaging 300 ml cartridges, 12 pc per box
600 ml sausages, 20 pc per box
Storage
Storage Conditions / 12 months from date of production if stored in undamaged original sealed
Shelf-Life containers, in dry conditions and protected from direct sunlight at temperatures
between +10°C and +25°C.
Mechanical / Physical
Properties
2
Tear Strength ~ 5.5 N/mm (+23°C / 50% r.h.) (DIN 53 515)
Shore A Hardness ~ 25 after 28 days (+23°C / 50% r.h.) (DIN 53 505)
E-Modulus 0.3 N/mm2 at 100% elongation (+23°C)
2
0.5 N/mm at 100% elongation (-20°C) (DIN EN ISO 8340)
Elongation at Break ~ 550% (+23°C / 50% r.h.) (DIN 53 504)
Elastic Recovery > 80% (+23°C / 50% r.h.) (DIN EN ISO 7389 B)
System
Information
Application Details
Consumption / The joint width must be designed to suit the movement capability of the sealant. In
Joint Design general the joint width must be > 10 mm and < 40 mm. A width to depth ratio of
~ 2 : 1 must be maintained.
Standard dimensions for concrete elements as per DIN 18 540 / table 3:
Joint Distance 2m 2 - 3.5 m 3.5 - 5 m 5 - 6.5 m 6.5 - 8 m
Joint Depth 8 mm 10 mm 12 mm 15 mm 15 mm
Joint Depth 8 mm 8 mm 10 mm 12 mm 15 mm
Backing:
Use only closed cell, polyethylene foam backing rods
Substrate Quality Clean and dry, homogeneous, free from oils and grease, dust and loose or friable
particles. Cement laitance and incompatible paints must be removed.
Application
Conditions /
Limitations
Substrate Temperature +5°C min. / +40°C max.
Ambient Temperature +5°C min. / +40°C max.
Substrate Moisture Dry
Content
Application
Instructions
®
Application Method / Sikaflex AT-Façade is supplied ready to use.
Tools
After suitable joint and substrate preparation, insert Backing Rod to required depth
and apply primer if necessary. Insert cartridge into the sealant gun and firmly
extrude Sikaflex® AT-Façade into the joint making sure that it is full in contact with
the side of the joint. Fill the joint, avoiding air entrapment. Sikaflex® AT-Façade
should be tooled firmly against the joint sides to ensure complete contact and good
adhesion.
Masking tape should be used where sharp exact joint lines or exceptionally neat
lines are required. Remove the tape whilst the sealant is still soft. Sleek joint with
smoothing liquid for a perfect sealant surface.
Cleaning of Tools Clean all tools and application equipment with Sika Sealant Remover /
SikaTopClean-T immediately after use. Hardened / cured material can only be
removed mechanically.
Notes on Application / Elastic sealants should generally not be over painted.
Limitations
However compatible coatings may cover the joint sides to max. 1 mm.
The compatibility must be tested according to DIN 52 452-4.
Colour variations may occur due to exposure to chemicals, high temperatures, UV-
radiation. However a change in colour will not adversely influence the technical
performance or the durability of the product.
Before using on natural stone contact our Technical Service Department.
Do not use Sikaflex® AT-Façade as a glass sealer, on bituminous substrates,
natural rubber, EPDM rubber or on building materials which might bleed oils,
plasticizers or solvents which could attack the sealant.
Not suitable for joints under water pressure or permanent water immersion.
Local Restrictions Please note that as a result of specific local regulations the performance of this
product may vary from country to country. Please consult the local Product Data
Sheet for the exact description of the application fields.
Health and Safety For information and advice on the safe handling, storage and disposal of chemical
products, users shall refer to the most recent Material Safety Data Sheet containing
Information physical, ecological, toxicological and other safety-related data.
Legal Notes The information, and, in particular, the recommendations relating to the application
and end-use of Sika products, are given in good faith based on Sika's current
knowledge and experience of the products when properly stored, handled and
applied under normal conditions in accordance with Sika’s recommendations. In
practice, the differences in materials, substrates and actual site conditions are such
Construction
Sika Services AG
Tüffenwies 16 Phone +41 44 436 40 40
CH-8048 Zurich Telefax +41 44 436 46 86
Switzerland www.sika.com