Académique Documents
Professionnel Documents
Culture Documents
IS:13155 Method of test for carbon type(PNA) analysis of mineral oil by infra red `
spectrophotometer.
IS:1367 Hot Dip Galvanized cooling on threaded fasteners.
IS:6272 Industrial cooling fans
IEEE:32 IEEE standard requirement terminology and test procedure for neutral grounding device.
ASTM-876M & IS 3024: American society for testing material for CRGO
CBIP Manual on transformer.
IS: 2393
SF6 GAS CIRCUIT BREAKERS
STANDARDS:
Sl. No. Standard No. Title
1. IEC-56 Specification for alternating current circuit breakers.
2. IEC-376 Specification and acceptance of new supply of sulphur
hexafluoride.
3. IS-5578& 11353 Making and arrangement for switchgear bus-bar, main
connections and auxiliary wiring.
4. IS-2147 Degree of protection provided for enclosures for low voltage
switchgear and control gear.
5 IS-325 Specification for three phase induction motors.
6. IS-13118 Specification for circuit breakers.
7. IS-2629 Recommended practice for hot dip galvanising
of iron and steel.
8. IEC-137 Bushings for AC Voltages.
9. IS-2099 High voltage porcelain bushings.
10. IS-4379 Identification of the contents of Industrial Gas Cylinders.
11. IS-7285 Seamless high carbon steel cylinders for permanent and
high pressure liquefiable gases
12. IS-802 Code of practice for use of structural steel in (PART-1)
overhead transmission line towers.
36 kV VACUUM CIRCUIT BREAKER (630A, 1250 & 2000 A)
Standards:
STANDARDS.
Sl. No Standard Title
No.
1. IS:9921 Alternating current isolators (dis-connectors)
and earthing switches.
2. IEC:129 -do-
3. IS:2544 Insulators.
4. IS:2147 Degree of protection provided by enclosure.
5. IS:4691 -do-
6. IS:325 Three phase induction motors.
7. IS:4722 Rotating electrical machines.
8. IS:262 Recommended practice for hot dip
galvanising of iron & steel.
9. IS:4759 Hot dip galvanisation coating on structural
steel.
10. IS:2633 Method of testing weight, thickness and
uniformity
11. IS:1573 Electroplated coating of zinc on iron and
steel.
12. IS:6735 Spring washers.
13. IS:2016 Plain washers.
14. – Indian Electricity Rules, 1956
STANDARD
The Post Insulators and their Hardwares shall comply as regards general requirements, test voltages and
test with the latest edition of IS 2544/1973 IS-5350
(P-II) 1973 IS-5350 (P-III) 1971/IEC-168/1979 except in so far as the same may be modified by this
Specification.
IS: 13925:1998. IS:9920 (AC Switches for voltages above 1000 V). IS: 1818-1972 IS: 2705
IS: 3070. IS: 3156 IS: 5553 IS: 1554 (Part-I) 1976
STANDARDS
Indian Standards Title International standards
IS-2026:1977-81 Specification of Power IEC-76
Transformer
IS-335/1983 Insulating Oil for transformer BS-148
& switchgear
IS-3639:1968 Fittings & Accessories for ASTM D-1275
Power Transformer
IS-2099:1986 Higher Voltage Porcelain IEC 296-1969
Bushings
IS-7421-1988 Low Voltage Porcelain Bushings
IS-3347 Dimensions for Outdoor DIN 42531 to 33, 23, 3
Bushings
IS-12444 Specification for Copper wire ASTM B-49
rods
IS-5/1964 Specification for colours for ready mixed paints
IS-6600/1972 Guide for loading of oil immersed Transformers
CBI&P Manual on transformer, Publication No.275
OUTDOOR NON SEALED TYPE THREE PHASE 11 KV/433V DISTRIBUTION TRANSFORMERS
OF 100 & 200 KVA CAPACITIES
STANDARDS:
The transformers shall conform in all respect to IS: 1180-1981 & IS: 2026-1977 except where specified otherwise.
LT TWO CORE, 3½ CORE AND FOUR CORE PVC INSULATED UNARMOURED CABLE OFF
SIZES FOR WORKING VOLTAGE UPTO & INCLUDING 1100 V, FOR SERVICE CONNECTIONS.
11 kV CROSS LINKED ETHYLENE INSULATED PVC SHEATHED SINGLE CORE AND THREE CORE POWER CABLES
STANDARDS
The cable covered under this Specification shall conform in all respects with the latest editions
of IS-7098 (Part-2) 1985 & IS-8130-1984 & IEC:502 of the latest version thereof.
INSULATOR HARDWARE FITTINGS
FOR BUS BARS
MOOSE, ZEBRA, PANTHER & TARANTULLA CONDUCTOR ON
220 kV/132 kV /66 kV SUB STATIONS
2.0 STANDARDS
2.1 The fittings shall conform to following Indian standards which shall mean latest revisions,
amendments/changes adopted and published unless otherwise specified hereinafter:
The DC Batteries shall be Normal Discharge type Valve Regulated Lead Acid (VRLA) and
shall conform to IS 15549: 2004/IEC 60896-21 & 22, 2004 standard. These shall be
factory filled, charged & suitable for a long life under continuous float operations and
occasional discharges. The 220 V DC systems should be unearthed and 48V DC system is
Positive Earth system.
.
Potentiometric Auto
Titrator for measurement
of Total Acidity in mg
KOH/gm
SAFETY BELT
1. SCOPE:
Earthing Stick/Discharge Rod with 35 sq.mm cable / lead for EHV Transmission lines and Sub-
stations.
1.0. Scope :
2.1. IEC-61230-1993 shall be offered by the bidder.
415
VOLTS L.T. SWITCH BOARDS.
1.03 STANDARDS:
IS-4064-1978 (part I & II) (latest edition). Is-2208-1962 (latest amended)..
IS:1651.
415 VOLTS MCCB AC DISTRIBUTION BOARD.