Académique Documents
Professionnel Documents
Culture Documents
General Specification
Code of Practice IS 456:2000
Country India
Bending Axes Biaxial
Section 1 Details
Definition
Name Section 1
Type Concrete
Material M45
Origin Centre
Dimensions
Diameter 1000.mm
Section Area 785400.mm2
Reinforcement Area 7854.mm2
Reinforcement 1.000%
Section Nodes
Node Y Z
[mm] [mm]
1 0.0 501.3
2 87.04 493.7
3 171.4 471.0
4 250.6 434.1
5 322.2 384.0
6 384.0 322.2
7 434.1 250.6
8 471.0 171.4
9 493.7 87.04
10 501.3 -44.32E-6
11 493.7 -87.05
12 471.0 -171.4
13 434.1 -250.6
14 384.0 -322.2
15 322.2 -384.0
16 250.6 -434.1
17 171.4 -471.0
18 87.04 -493.7
19 -88.64E-6 -501.3
20 -87.05 -493.7
21 -171.4 -471.0
22 -250.6 -434.1
23 -322.2 -384.0
24 -384.0 -322.2
25 -434.1 -250.6
26 -471.0 -171.4
27 -493.7 -87.04
28 -501.3 133.0E-6
29 -493.7 87.05
30 -471.0 171.4
31 -434.1 250.6
32 -384.0 322.2
33 -322.2 384.0
34 -250.6 434.1
35 -171.4 471.0
36 -87.04 493.7
Bars
Bar Y Z Diameter Material Type Pre-stress Pre-stress Appl. loads
Force Strain include/exclude
pre-stress
[mm] [mm] [mm] [kN]
1 0.0 400.5 25.00 500 Steel
2 153.3 370.0 25.00 500 Steel
3 283.2 283.2 25.00 500 Steel
4 370.0 153.3 25.00 500 Steel
5 400.5 -17.51E-6 25.00 500 Steel
6 370.0 -153.3 25.00 500 Steel
7 283.2 -283.2 25.00 500 Steel
8 153.3 -370.0 25.00 500 Steel
9 -35.01E-6 -400.5 25.00 500 Steel
10 -153.3 -370.0 25.00 500 Steel
11 -283.2 -283.2 25.00 500 Steel
12 -370.0 -153.3 25.00 500 Steel
13 -400.5 4.776E-6 25.00 500 Steel
14 -370.0 153.3 25.00 500 Steel
15 -283.2 283.2 25.00 500 Steel
16 -153.3 370.0 25.00 500 Steel
Elastic Properties
Note: Nmax is the maximum compressive force which can be carried by the section.
This is calculated by applying a constant strain across the entire section, using
ultimate material properties.
Reinforcement Properties
Name 500
fy 500.0N/mm2
Modulus 200000.N/mm2
Partial Safety Factor ms,ULS 1.150
ms,SLS 1.000
Maximum Strain 0.004174[-]
Stress/Strain Curve Elastic-plastic
Loading
Reference Point
All loading acts through the Reference Point.
All strain planes are defined relative to the Reference Point.
Definition Geometric
Centroid
Reference Point Coordinates y 0.0mm
z 0.0mm
Applied loads
Load Case N Myy Mzz
[kN] [kNm] [kNm]
1 6895. 412.7 100.9
2 5.627 191.1 251.1
3 1698. 415.6 206.6
4 5626. 475.7 75.89
5 2121. 142.1 321.0
6 3398. 315.6 499.0
7 -1822. 253.6 60.21
8 -2.558 218.3 3.740
9 4827. 282.5 67.43
10 0.6240 5.646 2.876
11 1199. 284.4 147.4
12 3980. 324.5 50.75
13 349.5 130.5 219.0
14 2509. 163.2 315.9
15 -492.0 10.58 104.0
16 -2.106 132.4 125.4
17 3396. 98.78 73.85
18 64.93 58.26 69.63
19 1157. 98.81 71.52
20 3396. 98.78 73.85
21 632.5 86.66 108.6
22 2402. 39.07 196.0
23 -203.7 0.5739 8.338
24 -203.7 34.06 8.393
Section 1 Details
1.00% reinforcement in section 1 (Section 1). Check this against code requirements.
Note: Cover to controlling bar measured to different side from crack location
Case 13
Crack Numbers
8 to 13 20 to 25 32 to 37 44 to 49 62 to 64
Note: Cover to controlling bar measured to different side from crack location
Case 15
Crack Numbers
6 to 11 18 to 23 30 to 35 42 to 47 60 to 65 72 to 77 84 to 89 96 to 101 114 to 119 126 to 131 138
to 143
150 to 155
168 to 173
180 to 185
192 to 197
204 to 209
Note: Cover to controlling bar measured to different side from crack location
Case 16
Crack Numbers
0 to 2 9 to 14 27 to 32 39 to 44 51 to 56 63 to 68 81 to 86 93 to 98 105 to 110 117 to 122 135 to
140
147 to 152
159 to 164
Note: Cover to controlling bar measured to different side from crack location
Case 13
Crack Numbers
8 to 13 20 to 25 32 to 37 44 to 49 62 to 64
Note: Cover to controlling bar measured to different side from crack location
Case 15
Crack Numbers
6 to 11 18 to 23 30 to 35 42 to 47 60 to 65 72 to 77 84 to 89 96 to 101 114 to 119 126 to 131 138
to 143
150 to 155
168 to 173
180 to 185
192 to 197
204 to 209
Note: Cover to controlling bar measured to different side from crack location
Case 16
Crack Numbers
0 to 2 9 to 14 27 to 32 39 to 44 51 to 56 63 to 68 81 to 86 93 to 98 105 to 110 117 to 122 135 to
140
147 to 152
159 to 164