Académique Documents
Professionnel Documents
Culture Documents
My-T-Glue® 745 is a toughened cyanoacrylate The rate of cure will depend on the bond-line gap.
instant bonding adhesive designed for bonding Thin bond lines result in high cure speeds,
rubber to metal parts, especially the galvanized increasing the bond gap will decrease the rate of
surfaces having low surface energy. The bond cure.
formed exhibits excellent oil resistance even at
elevated temperature of around 100 0C for shorter Cure Speed Vs. Activator
duration.
Where cure speed is unacceptably long due to large
Properties of Material gaps, applying activator to the surface will improve
cure speed. However, this can reduce ultimate
strength of the bond and therefore testing is
Technology : Cyanoacrylate
recommended to confirm effect.
Chemical Type : Ethyl Cyanoacrylate
Component : One component
Appearance : Transparent/ straw Adhesive Properties
coloured liquid
Sp. Gravity @ 25 °C : 1.06 After 24 hours @ 25±2 °C
Viscosity @ 25±2 °C, : 10-20 cP Lap Shear Strength, ASTM D 1002
Brookfield, Spindle # 1, Steel : 20 to 25 N/mm²
Speed100 r.p.m. Aluminum : 11 to 20 N/mm²
Secondary Cure : Activator ABS : Substrate failure
Key Substrate : Metals, Plastics and PVC : 4 to 6 N/mm²
Rubbers etc. Polycarbonate : 3.4 to 6 N/mm²
Application : Bonding Phenolic : 5 to 15 N/mm²
Neoprene : 10 to 15 N/mm²
Nitrile : 10 to 15 N/mm²
Curing Performance
After 24 hours @ 25±2 °C
Tensile Strength, ASTM D 897
Under normal conditions, the atmospheric moisture Steel : 12 to 25 N/mm²
initiates the curing process. Although full
functional strength is developed in a relatively
Hot Strength
short time, curing continues for at least 24 hours
before full chemical/solvent resistance is developed
Test : Lap Shear Strength, ASTM D 1002
Cure Speed Vs. Substrate Substrate : Steel
Cure : 24 hrs @ 25±2 °C
The rate of cure will depend on the substrate used. Tested at temperature
The fixture time achieved on different materials at
25°C/ 60 % relative humidity is shown below. This
is defined as the time to develop shear strength of
0.1 N/mm².
Fixture Time, Seconds
Mild Steel (degreased) : 5 to10
Aluminium : 5 to20
Neoprene : <5
Rubber, Nitrile : <5
ABS : 5 to20
PVC : 5 to10
Polycarbonate : 15 to 50
Phenolic : 5 to 20
TDS/745/CY/JR072012/1.1 Page 1 of 2
Heat Aging Safety Data Sheet (MSDS) and in compliance
with relevant local regulations.
Test : Lap Shear Strength, ASTM D 1002 My-T-Glue® 745 is not recommended for use
Substrate : Steel in pure oxygen and/or oxygen rich systems
Cure : 24 hrs @ 25±2 °C and should not be selected as a sealant for
Aged at temperature indicated and tested @ 25±2 chlorine or other strong oxidizing materials
°C. My-T-Glue® 745 is non-volatile and non-
flammable at room temperature.
Storage
Aged under condition indicated and tested @ 25±2 My-T-Glue® 745 is available in 20 gm and 50 gm.
°C.
Environment Temp % of Initial Strength
(0C) 100 500 1000 Note
hr hr hr
40 100 100 100 All statements, technical information and
Engine oil 100 90 80 78 recommendations set forth herein are based on tests
120 87 60 50 which Metlok Private Limited, believes to be
Water Glycol 40 100 100 100 reliable. However, Metlok Private Limited does not
50/50 87 100 85 85 guarantee their accuracy or completeness. We
Ethanol 40 100 100 100 cannot assume responsibility for the results
Isopropanol 40 100 100 100 obtained by others over whose methods we have no
1,1,1- control. It is the user's responsibility to determine
40 100 100 100
Trichloroethane suitability for the user's purpose of any production
methods mentioned herein and to adopt such
Directions for Use precautions as may be advisable for the protection
of property and of persons against any hazards that
1. For best performance clean all surfaces with a may be involved in the handling and use thereof. In
cleaning solvent and allow to dry no case will Metlok Private Limited be liable for
2. The bond surfaces should be clean and free direct, consequential economic or other damages.
from grease.
3. This product performs best in thin bond gaps. ****** ******* *********
4. Adhesive can be applied using dispensing tips Metlok Private Limited
supplied. Once the adhesive is dispensed, the (Bonding and Sealing Solutions)
bonded parts should be held in contact until An ISO 9001: 2008 Certified Company
the part has developed handling strength. Tel.: 07118-271543/271170/272468
5. Excess adhesive can be dissolved with Fax: 07118-272470
cleanup solvents, nitro methane or acetone Visit us at: www.Metlok.in
Handling
TDS/745/CY/JR072012/1.1 Page 2 of 2