Académique Documents
Professionnel Documents
Culture Documents
SECTION
BODY CONTROL SYSTEM
BCS B
E
CONTENTS
PRECAUTION ............................................... 3 DOOR LOCK ..............................................................14 F
DOOR LOCK : CONSULT Function (BCM -
PRECAUTIONS ................................................... 3 DOOR LOCK) ..........................................................15
Precaution for Technicians Using Medical Electric...... 3 G
Point to Be Checked Before Starting Maintenance REAR WINDOW DEFOGGER ...................................15
Work .......................................................................... 3 REAR WINDOW DEFOGGER : CONSULT Func-
Precaution for Supplemental Restraint System tion (BCM - REAR DEFOGGER) .............................16
H
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
BUZZER .....................................................................16
SIONER" ................................................................... 3
BUZZER : CONSULT Function (BCM - BUZZER)....16
Precaution for Removing 12V Battery ....................... 4
INT LAMP ...................................................................16 I
SYSTEM DESCRIPTION .............................. 5 INT LAMP : CONSULT Function (BCM - INT
LAMP) ......................................................................17
COMPONENT PARTS ........................................ 5
J
HEADLAMP ...............................................................18
BODY CONTROL SYSTEM ........................................ 5
HEADLAMP : CONSULT Function (BCM - HEAD
BODY CONTROL SYSTEM : Component Parts
LAMP) ......................................................................18
Location ..................................................................... 5 K
WIPER ........................................................................21
POWER CONSUMPTION CONTROL SYSTEM ......... 5
WIPER : CONSULT Function - WIPER ...................21
POWER CONSUMPTION CONTROL SYSTEM :
Component Parts Location ........................................ 5 FLASHER ...................................................................22 L
FLASHER : CONSULT Function (BCM - FLASH-
SYSTEM .............................................................. 6 ER) ..........................................................................22
BODY CONTROL SYSTEM ........................................ 6 BCS
INTELLIGENT KEY ....................................................23
BODY CONTROL SYSTEM : System Description...... 6
INTELLIGENT KEY : CONSULT Function (BCM -
COMBINATION SWITCH READING SYSTEM ........... 6 INTELLIGENT KEY) ................................................23
N
COMBINATION SWITCH READING SYSTEM : COMB SW ..................................................................26
System Description ................................................... 7
COMB SW : CONSULT Function (BCM - COMB
SIGNAL BUFFER SYSTEM ...................................... 10 SW) ..........................................................................26 O
SIGNAL BUFFER SYSTEM : System Description.... 10
BCM ...........................................................................26
POWER CONSUMPTION CONTROL SYSTEM ....... 10 BCM : CONSULT Function (BCM - BCM) ...............26
POWER CONSUMPTION CONTROL SYSTEM : P
IMMU ..........................................................................27
System Description ................................................. 11
IMMU : CONSULT Function (BCM - IMMU) ............27
DIAGNOSIS SYSTEM (BCM) ............................13 BATTERY SAVER .....................................................27
COMMON ITEM ......................................................... 13 BATTERY SAVER : CONSULT Function (BCM -
COMMON ITEM : CONSULT Function (BCM - BATTERY SAVER) ..................................................27
COMMON ITEM) ..................................................... 13
OPERATION PROHIBITION
WARNING: C
• Parts with strong magnet is used in this vehicle.
• Technicians using a medical electric device such as pacemaker must never perform operation on the
vehicle, as magnetic field can affect the device function by approaching to such parts.
D
NORMAL CHARGE PRECAUTION
WARNING:
• If a technician uses a medical electric device such as an implantable cardiac pacemaker or an E
implantable cardioverter defibrillator, the possible effects on the devices must be checked with the
device manufacturer before starting the charge operation.
• As radiated electromagnetic wave generated by on board charger at normal charge operation may
F
effect medical electric devices, a technician using a medical electric device such as implantable car-
diac pacemaker or an implantable cardioverter defibrillator must not enter the vehicle compartment
(including luggage room) during normal charge operation.
G
Precaution at telematics system operation
WARNING:
• If a technician uses implantable cardiac pacemaker or implantable cardioverter defibrillator (ICD), H
avoid the device implanted part from approaching within approximately 220 mm (8.66 in) from inte-
rior/exterior antenna.
• The electromagnetic wave of TCU might affect the function of the implantable cardiac pacemaker or
the implantable cardioverter defibrillator (ICD), when using the service, etc. I
• If a technician uses other medical electric devices than implantable cardiac pacemaker or implant-
able cardioverter defibrillator(ICD), the electromagnetic wave of TCU might affect the function of the
device. The possible effects on the devices must be checked with the device manufacturer before J
TCU use.
Precaution at intelligent key system operation
WARNING: K
• If a technician uses implantable cardiac pacemaker or implantable cardioverter defibrillator (ICD),
avoid the device implanted part from approaching within approximately 220 mm (8.66 in) from inte-
rior/exterior antenna. L
• The electromagnetic wave of intelligent key might affect the function of the implantable cardiac
pacemaker or the implantable cardioverter defibrillator (ICD), at door operation, at each request
switch operation, or at engine starting.
• If a technician uses other medical electric devices than implantable cardiac pacemaker or implant- BCS
able cardioverter defibrillator (ICD), the electromagnetic wave of intelligent key might affect the func-
tion of the device. The possible effects on the devices must be checked with the device
manufacturer before intelligent key use. N
Point to Be Checked Before Starting Maintenance Work INFOID:0000000007079489
The high voltage system may starts automatically. It is required to check that the timer air conditioner O
and timer charge (during EVSE connection) are not set before starting maintenance work.
NOTE:
If the timer air conditioner or timer charge (during EVSE connection) is set, the high voltage system starts
P
automatically even when the power switch is in OFF state.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000007003267
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
When removing the 12V battery, turn ON/OFF the power switch and check that the charging status indicator
does not blink. The 12V battery must be removed within one hour after checking the indicator lamp.
NOTE:
• The automatic 12V battery charge control may start even when the power switch is in OFF state.
• The automatic 12V battery charge control does not start within approximately one hour when the power
switch is turned ON/OFF.
JMMIA0607ZZ
H
1. BCM
A. Behind of instrument lower panel LH
(Left side back)
I
POWER CONSUMPTION CONTROL SYSTEM
POWER CONSUMPTION CONTROL SYSTEM : Component Parts Location J
INFOID:0000000006923134
BCS
O
JMMIA0608ZZ
OUTLINE
• BCM (Body Control Module) controls the various electrical components. It inputs the information required to
the control from CAN communication and the signal received from each switch and sensor.
• BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power saving con-
trol function that reduces the power consumption with the power switch OFF.
• BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT and various set-
tings.
BCM CONTROL FUNCTION LIST
System Reference
BCS-7, "COMBINATION SWITCH READING SYSTEM : System
Combination switch reading system
Description"
Signal buffer system BCS-10, "SIGNAL BUFFER SYSTEM : System Description"
BCS-11, "POWER CONSUMPTION CONTROL SYSTEM : Sys-
Power consumption control system
tem Description"
Headlamp system EXL-10, "HEADLAMP SYSTEM : System Description"
Auto light system EXL-12, "AUTO LIGHT SYSTEM : System Description"
EXL-15, "TURN SIGNAL AND HAZARD WARNING LAMP SYS-
Turn signal and hazard warning lamp system
TEM : System Description"
EXL-16, "PARKING, LICENSE PLATE, SIDE MARKER AND
Parking, license plate, side marker and tail lamps system
TAIL LAMP SYSTEM : System Description"
Front fog lamp system EXL-19, "FRONT FOG LAMP SYSTEM : System Description"
EXL-21, "EXTERIOR LAMP BATTERY SAVER SYSTEM : Sys-
Exterior lamp battery saver system
tem Description"
INL-7, "INTERIOR ROOM LAMP CONTROL SYSTEM : System
Interior room lamp control system
Description"
INL-10, "INTERIOR ROOM LAMP BATTERY SAVER SYSTEM :
Interior room lamp battery saver system
System Description"
WW-7, "FRONT WIPER AND WASHER SYSTEM : System De-
Front wiper and washer system
scription"
WW-11, "REAR WIPER AND WASHER SYSTEM : System De-
Rear wiper and washer system
scription"
Warning chime system WCS-6, "WARNING CHIME SYSTEM : System Description"
Power door lock system DLK-14, "System Description"
Intelligent Key system DLK-17, "INTELLIGENT KEY SYSTEM : System Description"
Back door opener system DLK-31, "System Description"
SEC-14, "NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS :
Nissan Vehicle Immobilizer System (NVIS) - NATS
System Description"
Vehicle security system SEC-19, "VEHICLE SECURITY SYSTEM : System Diagram"
Rear window defogger system DEF-5, "System Description"
Power window system [Retained accessory power (RAP function)] PWC-7, "System Description"
Tire pressure monitoring system WT-9, "System Description"
A
SYSTEM DIAGRAM
JMMIA0636GB
NOTE: G
*: TAIL LAMP switch links lighting switch 1ST and 2ND positions.
OUTLINE
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the H
status of each switch.
• BCM has a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a
maximum of 20 switch status. I
COMBINATION SWITCH MATRIX
Combination switch circuit
J
BCS
O
JMMIA0637GB
NOTE:
*: TAIL LAMP switch links lighting switch 1ST and 2ND positions.
P
Combination switch INPUT-OUTPUT system list
System INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5
OUTPUT 1 — FR WASHER FR WIPER LOW TURN LH TURN RH
OUTPUT 2 FR WIPER HI — FR WIPER INT PASSING HEADLAMP 1
OUTPUT 3 WIP VOLUME 1 RR WASHER — HEADLAMP 2 HI BEAM
JPMIA0609GB
NOTE:
BCM reads the status of the combination switch at 60 ms interval when BCM is controlled at low power con-
sumption control mode.
• BCM operates as follows and judges the status of the combination switch.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 1 → 2 → 3 → 4 → 5, and outputs
voltage waveform.
- The voltage waveform of OUTPUT corresponding to the formed circuit is input into the interface on INPUT
side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.
JMMIA0326GB
Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to “1 - 5” and OUTPUT 1 - 5 to “A - E”.
Example 1: When a switch (TAIL LAMP switch) is turned ON
JPMIA1545GB F
• BCM detects the combination switch status signal “5D” when the signal of OUTPUT 4 is input to INPUT 5.
• BCM judges that the TAIL LAMP switch is ON when the signal “5D” is detected.
Example 2: When some switches (TURN RH switch, TAIL LAMP switch) are turned ON G
• The circuits between OUTPUT 1 and INPUT 5 and between OUTPUT 4 and INPUT 5 are formed when the
TURN RH switch and TAIL LAMP switch are turned ON.
H
JPMIA1546GB
BCS
• BCM detects the combination switch status signal “5AD” when the signals of OUTPUT 1 and OUTPUT 4 are
input to INPUT 5.
• BCM judges that the TURN RH switch and TAIL LAMP switch are ON when the signal “5AD” is detected.
N
WIPER VOLUME DIAL POSITION
BCM judges the wiper volume dial 1 - 7 by the status of WIP VOLUME 1, 2 and 3 switches.
Switch status
O
Wiper volume
dial position WIP VOLUME 1 WIP VOLUME 2 WIP VOLUME 3
1 ON ON ON
P
2 ON ON OFF
3 ON OFF OFF
4 OFF OFF OFF
5 OFF OFF ON
SYSTEM DIAGRAM
JMMIA0813GB
OUTLINE
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
Signal transmission function list
A
SYSTEM DIAGRAM
JMMIA0613GB F
OUTLINE
• BCM incorporates a power saving control function that reduces the power consumption according to the
vehicle status. G
• BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit (IPDM E/R, combination meter and Electrically-driven Intelligent Brake unit) that oper-
ates with the power switch OFF. H
Wake-up operation
• BCM transmits sleep wake up signal (wake up) to each unit when any condition listed below is established,
and then goes into normal mode from low power consumption mode.
• Each unit starts transmissions with CAN communication by receiving sleep wake up signals. Each unit trans-
mit wake up signals to BCM with CAN communication to convey the start of CAN communication.
Wake-up condition
Wake-up condition
• Receiving the sleep-ready signal (Not-ready) from any units
• Power switch (push switch): OFF→ ON
• Hazard switch: ON
• HI BEAM switch: OFF → ON, ON → OFF
• PASSING switch: OFF → ON, ON → OFF
• HEADLAMP 1 switch: OFF → ON, ON → OFF
• HEADLAMP 2 switch: OFF → ON, ON → OFF
• TAIL LAMP switch: OFF → ON
• FR FOG switch: OFF → ON, ON → OFF
• TURN RH: OFF → ON, ON → OFF
• TURN LH: OFF → ON, ON → OFF
• Driver door switch: OFF → ON, ON → OFF
• Passenger door switch: OFF → ON, ON → OFF
• Rear RH door switch: OFF → ON, ON → OFF
• Rear LH door switch: OFF → ON, ON → OFF
• Back door switch: OFF → ON, ON → OFF
• Driver door request switch: OFF → ON
• Passenger door request switch: OFF → ON
• Back door request switch: OFF → ON
• Back door opener switch: OFF → ON
• Stop lamp switch: ON
• Door lock and unlock switch: NEUTRAL → LOCK, NEUTRAL → UNLOCK
• Front door lock assembly (driver side) (door key cylinder switch): NEUTRAL → LOCK, NEUTRAL → UNLOCK
• Remote keyless entry receiver communication: Receiving
• Front door lock assembly (driver side) (unlock sensor): OFF → ON, ON → OFF
SYSTEM APPLICATION
G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item H
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
K
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
— AIR CONDITONER* × × L
Intelligent Key system INTELLIGENT KEY × × ×
Combination switch COMB SW ×
BCS
Body control system BCM ×
NVIS - NATS IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × × N
Back door open TRUNK ×
Theft warning alarm THEFT ALM × × ×
RAP system RETAINED PWR × O
Signal buffer system SIGNAL BUFFER × ×
TPMS AIR PRESSURE MONITOR × × ×
P
*: This item is displayed, but not used.
A
WORK SUPPORT
DATA MONITOR
I
Monitor Item Contents
REQ SW-DR Indicated [On/Off] condition of door request switch (driver side)
J
REQ SW-AS Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-BD/TR Indicated [On/Off] condition of back door request switch
DOOR SW-DR Indicated [On/Off] condition of front door switch (driver side) K
DOOR SW-AS Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR Indicated [On/Off] condition of rear door switch RH
L
DOOR SW-RL Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK Indicated [On/Off] condition of back door switch
CDL LOCK SW Indicated [On/Off] condition of lock signal from door lock unlock switch BCS
CDL UNLOCK SW Indicated [On/Off] condition of unlock signal from door lock unlock switch
KEY CYL LK-SW Indicated [On/Off] condition of lock signal from door key cylinder
N
KEY CYL UN-SW Indicated [On/Off] condition of unlock signal from door key cylinder
ACTIVE TEST
O
Test item Description
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LOCK” on CONSULT screen is touched P
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is
DOOR LOCK
touched
• The door lock actuator (passenger side) is unlocked when “ UNLK” on CONSULT screen is
touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT screen is touched
DATA MONITOR
ACTIVE TEST
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER) INFOID:0000000007032369
DATA MONITOR
Display item
Description
[Unit]
PUSH SW
Status of push-button power switch judged by BCM.
[On/Off]
UNLK SEN-DR
Status of unlock sensor judged by BCM.
[On/Off]
VEH SPEED 1
Value of vehicle speed signal received from combination meter with CAN communication line.
[km/h]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM using the combination switch readout function.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]
CDL LOCK SW
Status of door lock unlock switch judged by BCM.
[On/Off]
ACTIVE TEST
Display item
Description
[Unit]
SEAT BELT WARN TEST The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
ID REGIST WARNING The ID regist warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
INT LAMP
A
WORK SUPPORT
JMLIA0961GB F
DATA MONITOR O
Monitor item
Description
[Unit]
P
REQ SW-DR
The switch status input from request switch (driver side)
[On/Off]
REQ SW-AS
The switch status input from request switch (passenger side)
[On/Off]
ACTIVE TEST
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) INFOID:0000000007032366
WORK SUPPORT
Without the
MODE 2
function
E
MODE 3 30 sec.
MODE 4 60 sec. Sets delay timer function timer operation time
ILL DELAY SET*1 (All doors closed)
MODE 5 90 sec. F
MODE 6 120 sec.
MODE 7 150 sec.
MODE 8 180 sec. G
MODE 1*2 With twilight ON custom & with wiper INT, LO and HI
MODE 2 With twilight ON custom & with wiper LO and HI H
MODE 3 With twilight ON custom & without
AUTO LIGHT LOGIC SET*1
MODE 4 Without twilight ON custom & with wiper INT, LO and HI
MODE 5 Without twilight ON custom & with wiper LO and HI
I
MODE 6 Without twilight ON custom & without
*1: For models without auto light system, this item is displayed but is not operated. J
*2: Factory setting
DATA MONITOR
K
Monitor item
Description
[Unit]
L
PUSH SW
The switch status input from power switch
[On/Off]
ENGINE STATE
The traction motor status received from VCM via CAN communication BCS
[Stop/Stall/Crank/Run]
VEH SPEED 1 The value of the vehicle speed received from combination meter via CAN communi-
[km/h] cation
N
FR FOG SW*2
[On/Off]
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL
The switch status input from rear door switch LH
[On/Off]
DOOR SW-BK
The switch status input from back door switch
[On/Off]
OPTICAL SENSOR NOTE:
[On/Off/NG] This item is indicated, but can not monitored
OPTI SEN (DTCT)*1 The value of outside brightness voltage input from the optical sensor
[V]
OPTI SEN (FILT)*1 The value of outside brightness voltage filtered by BCM
[V]
*1: For models without auto light system, this item is not displayed.
*2: For models without front fog lamp, this item is displayed but is not monitored.
ACTIVE TEST
WORK SUPPORT D
Monitor Item
Description H
[Unit]
PUSH SW
The switch status input from power switch (push switch)
[Off/On]
VEH SPEED 1 Displays the value of the vehicle speed signal received from combination meter via CAN com- I
[km/h] munication
FR WIPER HI
[Off/On] J
FR WIPER LOW
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
FR WASHER SW K
[Off/On]
FR WIPER INT
[Off/On] L
FR WIPER STOP Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
[Off/On] communication.
INT VOLUME BCS
Status of each switch judged by BCM using the combination switch reading function
[1 − 7]
RR WIPER ON
[Off/On] N
RR WIPER INT
Status of each switch judged by BCM using the combination switch reading function
[Off/On]
RR WASHER SW O
[Off/On]
RR WIPER STOP
Rear wiper motor (stop position) status input from the rear wiper motor
[Off/On]
P
H/L WASH SW NOTE:
[Off/On] The item is indicated, but not monitored
ACTIVE TEST
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) INFOID:0000000007032367
WORK SUPPORT
Monitor item
Description
[Unit]
REQ SW-DR
The switch status input from the request switch (driver side)
[On/Off]
REQ SW-AS
The switch status input from the request switch (passenger side)
[On/Off]
PUSH SW
The switch status input from the power switch
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch
[On/Off]
RKE-LOCK
Lock signal status received from the remote keyless entry receiver
[On/Off]
RKE-UNLOCK
Unlock signal status received from the remote keyless entry receiver
[On/Off]
RKE-PANIC
Panic alarm signal status received from the remote keyless entry receiver
[On/Off]
ACTIVE TEST
WORK SUPPORT B
NOTE:
TRUNK/GLASS HATCH OPEN
This item is displayed, but cannot be used
F
Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not
operate (OFF) with this mode
HORN WITH KEYLESS LOCK
• On: Operate
• Off: Non-operation G
Panic alarm button pressing time on Intelligent Key remote control button can be selected from
the following with this mode
PANIC ALARM SET • MODE 1: 0.5 sec.
H
• MODE 2: Non-operation
• MODE 3: 1.5 sec.
NOTE:
TRUNK OPEN DELAY I
This item is displayed, but cannot be used
Intelligent Key low battery warning mode can be changed to operation with this mode
LO- BATT OF KEY FOB WARN • On: Operate
• Off: Non-operation J
Key reminder function mode can be changed to operation with this mode
ANTI KEY LOCK IN FUNCTI • On: Operate
• Off: Non-operation
K
Hazard reminder function mode by door request switch and Intelligent Key button can be se-
lected from the following with this mode
• Lock Only: Door lock operation only
HAZARD ANSWER BACK L
• Unlock Only: Door unlock operation only
• Lock/Unlock: Lock and unlock operation
• Off: Non-operation
Buzzer reminder function (lock operation) mode by door request switch can be selected from BCS
the following with this mode
ANS BACK I-KEY LOCK • Horn Chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• Off: Non-operation N
Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
ANS BACK I-KEY UNLOCK
• On: Operate O
• Off: Non-operation
NOTE:
SHORT CRANKING OUTPUT
This item is displayed, but cannot be used
P
SELF-DIAG RESULT
Refer to BCS-54, "DTC Index".
DATA MONITOR
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW) INFOID:0000000006923148
DATA MONITOR
BCM
BCM : CONSULT Function (BCM - BCM) INFOID:0000000006923149
WORK SUPPORT
Item Description A
RESET SETTING VALUE Return a value set with Work Support of each system to a default value in factory shipment.
IMMU B
IMMU : CONSULT Function (BCM - IMMU) INFOID:0000000007032361
DATA MONITOR C
ACTIVE TEST
I
Test item Description
This test is able to check security indicator lamp operation.
THEFT IND J
Security indicator lamp is turned on when “ON” on CONSULT screen touched.
WORK SUPPORT
K
Service item Description
CONFIRM DONGLE ID It is possible to check that dongle unit is applied to the vehicle.
L
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER) INFOID:0000000007032365
BCS
WORK SUPPORT
DATA MONITOR
Monitor item
Description
[Unit]
REQ SW-DR
The switch status input from request switch (driver side)
[On/Off]
REQ SW-AS
The switch status input from front request switch (passenger side)
[On/Off]
REQ SW-RR
[On/Off] NOTE:
REQ SW-RL The item is indicated, but not monitored.
[On/Off]
PUSH SW
The switch status input from power switch
[On/Off]
UNLK SEN-DR
Driver door unlock status input unlock sensor
[On/Off]
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL
The switch status input from rear door switch LH
[On/Off]
DOOR SW- BK
The switch status input from back door switch
[On/Off]
CDL LOCK SW
Lock switch status input from door lock and unlock switch
[On/Off]
CDL UNLOCK SW
Unlock switch status input from door lock and unlock switch
[On/Off]
TRNK/HAT MNTR NOTE:
[On/Off] The item is indicated, but not monitored
KEY CYL LK-SW
Lock switch status received from door key cylinder switch
[On/Off]
KEY CYL UN-SW
Unlock switch status received from door key cylinder switch
[On/Off]
RKE-LOCK
Lock signal status received from remote keyless entry receiver
[On/Off]
RKE-UNLOCK
Unlock signal status received from remote keyless entry receiver
[On/Off]
ACTIVE TEST
DATA MONITOR
WORK SUPPORT
F
Service Item Description
SECURITY ALARM SET This mode is able to confirm and change security alarm ON-OFF setting.
The switch which triggered vehicle security alarm is recorded. G
THEFT ALM TRG This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
DATA MONITOR H
RETAIND PWR
RETAIND PWR : CONSULT Function (BCM - RETAINED PWR) INFOID:0000000007032362
DATA MONITOR
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER) INFOID:0000000006923153
DATA MONITOR
ACTIVE TEST
Opera-
Test item Description
tion
Off NOTE:
OIL PRESSURE SW
On This item is displayed, but not tested.
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
Item Description
J
WARNING LAMP Low tire pressure warning lamp can be turned ON arbitrarily.
NOTE:
ID REGIST WARNING
Displayed but not used in TPMS.
K
NOTE:
RUN FLAT TIRE W/L
Displayed but not used in TPMS.
NOTE: L
RUN FLAT/T WARN BUZZER
Displayed but not used in TPMS.
FLASHER Turn signal lamps can be turned ON arbitrarily.
HORN This test is able to check to check that the horn sounds. BCS
WORK SUPPORT
N
Item Description
ID READ Registered tire pressure sensor ID can be displayed.
ID REGIST Tire pressure sensor ID can be registered. O
L
JMMIA0323ZZ
JPMIA0342JP
2.0 V
All switches OFF 0V
Turn signal switch LH
Lighting switch PASS
PKIB4956J
0.8 V
All switches OFF 0V
Front wiper switch LO
Front wiper switch MIST
Combination
4 Combination switch switch Front wiper switch INT
Ground Input
(BR) INPUT 3 (Wiper volume
dial 4)
Lighting switch AUTO
PKIB4958J
1.0 V
F
Rear wiper switch ON
(Wiper volume dial 4)
G
PKIB4956J
0.8 V
All switches OFF
0V H
(Wiper volume dial 4)
Front wiper switch HI
(Wiper volume dial 4)
I
Rear wiper switch INT
(Wiper volume dial 4)
J
Wiper volume dial 3
(All switches OFF) PKIB4958J
1.0 V
K
1.9 V
PKIB4956J
0.8 V P
PKIB4960J
7.0 - 8.0 V
UNLOCK position 0V
PKIB4960J
7.0 - 8.0 V
LOCK position 0V
OFF (Brake pedal is not
0V
9 Stop lamp depressed)
Ground Stop lamp switch 1 Input
(BR) switch ON (Brake pedal is de-
9 - 16 V
pressed)
JPMIA0012GB
1.0 - 1.5 V
LOCK position 0V
JPMIA0012GB
1.0 - 1.5 V
UNLOCK position 0V
When bright outside of the
Close to 5 V
14 Power switch vehicle
Ground Optical sensor Input
(G) ON When dark outside of the
Close to 0 V
vehicle
JPMIA0012GB
1.0 - 1.5 V D
Being pressed 0V
Either of the following
conditions
E
• Lighting switch OFF
• The area around the ve- 0V
16 Power switch hicle is bright (Shine a
Ground Dimmer signal Output F
(R) ON light on the optical sen-
sor)
The area around the vehi-
cle is dark (Block the light 7.5 - 16 V G
from the optical sensor)
BCS
23 Security indicator Security indica- Blinking (Power switch
Ground Output
(R) lamp tor lamp OFF)
N
JPMIA0590GB
12.0 V
OFF 9 - 16 V O
JMKIA6233JP
29 OFF 9 - 16 V
Ground Hazard switch Input Hazard switch
(P) ON 0 - 1.5 V
Pressed 0V
JPMIA0012GB
1.0 - 1.5 V
7.0 - 8.0 V
UNLOCK status (Unlock
0V
sensor switch ON)
PKIB4960J
7.0 - 8.0 V
32 Combination switch Combination
Ground Output Front fog lamp switch ON
(LG) OUTPUT 5 switch
(Wiper volume dial 4)
Rear wiper switch ON
(Wiper volume dial 4)
Any of the condition below
with all switches OFF
• Wiper volume dial 1
• Wiper volume dial 2 PKIB4956J
• Wiper volume dial 6 1.0 V
• Wiper volume dial 7
PKIB4960J
7.0 - 8.0 V D
33 Combination switch Combination Lighting switch 1ST
Ground Output (Wiper volume dial 4)
(Y) OUTPUT 4 switch
Lighting switch AUTO
E
(Wiper volume dial 4)
Rear wiper switch INT
(Wiper volume dial 4) F
Any of the condition below
with all switches OFF
PKIB4958J
• Wiper volume dial 1 G
1.2 V
• Wiper volume dial 5
• Wiper volume dial 6
PKIB4960J
7.0 - 8.0 V
J
Combination PKIB4960J
1.2 V
PKIB4960J
Combination
36 Combination switch switch 7.0 - 8.0 V
Ground Output
(P) OUTPUT 1 (Wiper volume Turn signal switch RH
dial 4)
Turn signal switch LH
Front wiper switch LO
Front wiper switch MIST
1.2 V
37 P position 0 - 1.5 V
Ground P position Input Shift position
(W) Any position other than P 6 - 16 V
Power switch
OFF (Remote
keyless entry When operating either C
communication) button on Intelligent Key
D
JMMIA0572GB
E
38 Receiver communi- Input/
Ground
(SB) cation Output Waiting
F
Power switch JMMIA0573GB
ON (TPMS
communication) G
JMMIA0574GB I
39 Input/
Ground CAN-H — —
(L) Output
40 Input/ J
Ground CAN-L — —
(P) Output
OFF
43 Back door (When back door closed) L
Ground Back door switch Input
(Y) switch
PKIB4960J
7.0 - 8.0 V
ON (When passenger
0V
door opened)
7.0 - 8.0 V
ON (When rear RH door
0V
opened)
7.0 - 8.0 V
ON (When driver door
0V
opened)
7.0 - 8.0 V
ON (When rear door LH
0V
opened)
54 OFF (Stopped) 0V
Ground Rear wiper Output Rear wiper
(P) ON (Activated) 9 - 16 V
UNLOCK (Actuator is acti-
9 - 16 V
55 vated)
Ground Rear door UNLOCK Output Rear door
(GR) Other then UNLOCK (Ac-
0V
tuator is not activated)
Interior room lamp battery saver is activated.
0V
(Cuts the interior room lamp power supply)
56 Interior room lamp Interior room lamp battery saver is not acti-
Ground Output
(P) power supply vated.
9 - 16 V
(Outputs the interior room lamp power sup-
ply)
E
60 Power switch
Ground Turn signal LH Output
(V) ON Turn signal switch LH
F
PKIC6370E
6.5 V
(Turn signal lamp turn on: 9 - 16
V) G
Turn signal switch OFF 0V
61 Power switch
Ground Turn signal RH Output I
(W) ON Turn signal switch RH
PKIC6370E
6.5 V J
(Turn signal lamp turn on: 9 - 16
V)
B
When Intelligent Key is
not in the antenna detec-
tion area
(The distance between In- C
telligent Key and antenna:
Approx. 2 m)
When the pas- JMKIA5954GB
JMKIA5951GB
JMKIA3839GB
JMKIA5951GB
JMKIA3839GB
JMKIA5951GB
JMKIA3839GB
JMKIA5951GB
E
When Intelligent Key is in
the antenna detection
area
F
JMKIA3839GB
JMKIA5951GB
I
88 Luggage room an- Power switch
Ground Output
(V) tenna (+) ON
J
JMKIA3839GB
L
BCS
When Intelligent Key is
not in the antenna detec-
tion area
N
JMKIA5951GB
JMKIA3839GB
JPMIA1554GB
6.0 - 7.0 V
102 P or N position 9 - 16 V
Ground P/N position Input Shift position
(R) Except P and N positions 0 - 1.5 V
104 Wake-up (electric
Ground Output Power switch ON 9 - 16 V
(LG) shift)
105
Ground Stop lamp switch 2 Input Power switch OFF 9 - 16 V
(P)
Fail-safe INFOID:0000000006923155
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority K
chart.
Priority DTC L
1 B2562: LOW VOLTAGE
• U1000: CAN COMM
2 • U1010: CONTROL UNIT (CAN) BCS
• U0293: HV C/U CAN COMM
• B2192: ID DISCORD BCM-ECM*
• B2193: CHAIN OF BCM-ECM*
3 N
• B2195: ANTI-SCANNING
• B2198: NATS ANTENNA AMP
NOTE:
The details of time display are as follows.
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-13, "COM-
MON ITEM : CONSULT Function (BCM - COMMON ITEM)".
Freeze Frame
Data
Tire pressure
•Vehicle Speed Intelligent Key Reference
CONSULT display Fail-safe monitor warning
•Odo/Trip Meter warning lamp ON page
lamp ON
•Vehicle Condi-
tion
No DTC is detected.
further testing — — — — —
may be required.
U1000: CAN COMM — — — — BCS-65
U1010: CONTROL UNIT (CAN) — — — — BCS-66
BCS
JCMWA6918GB
JCMWA6919GB
BCS
JCMWA6920GB
JCMWA6921GB
BCS
JCMWA6922GB
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
NOTE:
When replacing BCM, perform the system initialization (NATS).
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Work Proce-
dure INFOID:0000000006971045
>> GO TO 2.
2.REPLACE BCM
Replace BCM. Refer to BCS-76, "Removal and Installation".
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to BCS-63, "CONFIGURATION (BCM) : Work Procedure".
>> GO TO 4.
4.INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS)
A
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows.
B
Function Description
• Reads the vehicle configuration of current BCM.
READ CONFIGURATION
• Saves the read vehicle configuration.
C
WRITE CONFIGURATION - Manual selection Writes the vehicle configuration with manual selection.
WRITE CONFIGURATION - Config file Writes the vehicle configuration with saved data.
NOTE: D
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
CAUTION: E
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
F
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
G
CONFIGURATION (BCM) : Work Procedure INFOID:0000000006971173
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file”.
K
>> GO TO 4.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally if
the setting is not corret.
SETTING ITEM
NOTE
Items Setting value
AUTO LIGHT WITH ⇔ WITHOUT —
THEFT ALM AREA MODE2 —
⇔: Items which confirm vehicle specifications
BCS
1.REPLACE BCM
When DTC “U1010” is detected, replace BCM.
H
1.VCM SELF-DIAG RESULTS
Perform “Self-Diagnostic Result” of VCM with CONSULT. Refer to EVC-78, "DTC Index".
Is any DTC detected? I
YES >> Repair or replace the malfunctioning part.
NO >> Replace BCM. Refer to BCS-76, "Removal and Installation".
J
BCS
U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from
the ABS actuator and electric unit (control unit).
DTC Logic INFOID:0000000006923172
BCS
Terminals
(+) (−) Voltage
BCM (Approx.)
Connector Terminal
Ground
70
M69 9 -16 V
57
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal Ground
M69 67 Existed
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
BCM
System Continuity
Connector Terminal I
OUTPUT 1 36
OUTPUT 2 35 Ground
J
OUTPUT 3 M68 34 Not existed
OUTPUT 4 33
OUTPUT 5 32 K
Does continuity exist?
YES >> Repair harnesses or connectors.
NO >> GO TO 3. L
Terminals N
(+) (−) Voltage
System
BCM (Approx.)
O
Connector Terminal
OUTPUT 1 36
OUTPUT 2 35 P
Ground
OUTPUT 3 34
OUTPUT 4 M68 33
OUTPUT 5 32 PKIB4960J
7.0 - 8.0 V
Is the measurement value normal?
BCM
System Continuity
Connector Terminal I
INPUT 1 6
INPUT 2 5 Ground
J
INPUT 3 M68 4 Not existed
INPUT 4 3
INPUT 5 2 K
Does continuity exist?
YES >> Repair harnesses or connectors.
NO >> GO TO 3. L
HEAD LAMP SW 1
HEAD LAMP SW 2
D
RR WASHER SW
AUTO LIGHT SW
FR WASHER SW
TURN SIGNAL R
TURN SIGNAL L
FR WIPER LOW
TAIL LAMP SW
RR WIPER INT
RR WIPER ON
FR WIPER INT
PASSING SW
FR WIPER HI
INT VOLUME
HI BEAM SW
FR FOG SW
Malfunc-
tion com-
bination
E
× × × × A F
× × × × B
× × × × C
G
× × × × D
× × × E
× × × F H
× × × × G
× × × H
× × × × I I
× × × × J
All Items K J
If only one item is detected or the item is not applicable to the combinations A to K L
3. Identify the malfunctioning part from the agreed combination and repair or replace the part.
K
Malfunction
Malfunctioning part Repair or replace
combination
L
A Combination switch OUTPUT 1 circuit
B Combination switch OUTPUT 2 circuit
Inspect the combination switch output circuit applicable to the malfunction-
C Combination switch OUTPUT 3 circuit BCS
ing part. Refer to BCS-71, "Diagnosis Procedure".
D Combination switch OUTPUT 4 circuit
E Combination switch OUTPUT 5 circuit
F Combination switch INPUT 1 circuit N
G Combination switch INPUT 2 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
H Combination switch INPUT 3 circuit
part. Refer to BCS-73, "Diagnosis Procedure". O
I Combination switch INPUT 4 circuit
J Combination switch INPUT 5 circuit
K BCM Replace BCM. Refer to BCS-76, "Removal and Installation". P
L Combination switch Replace combination switch.
NOTE:
Before replacing BCM, perform “READ CONFIGURATION” to save or print current vehicle specification. Refer
to BCS-62, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description".
REMOVAL
1. Disconnect the 12V battery cable from the negative terminal.
2. Remove instrument lower panel. Refer to IP-13, "Removal and Installation".
3. Remove fuse block (J/B).
4. Remove harness clip.
5. Remove BCM mounting screws.
6. Remove BCM and disconnect the connectors.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to perform “WRITE CONFIGURATION” when replacing BCM. Op not doing so, BCM control
function does not operate normally.
NOTE:
Be sure to perform the system initialization (NATS) when replacing BCM. Refer to BCS-62, "ADDITIONAL
SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Work Procedure".
JMMIA0383ZZ
H
REMOVAL
1. Disconnect the 12V battery cable from the negative terminal.
2. Remove steering column cover. Refer to IP-13, "Removal and Installation". I
3. Remove screws.
4. Disconnect the connector.
J
5. Pull up the combination switch to remove it.
INSTALLATION
Install in the reverse order of removal. K
BCS