Académique Documents
Professionnel Documents
Culture Documents
Outdoor/Indoor
200214-ed1
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other
trademarks are the property of their respective owners.
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for
inaccuracies contained herein.
Copyright © 2013Alcatel-Lucent
Edition 1.0
Status: Released
WWW.Alcatel-Lucent.com
3
COPYRIGHT © 2012 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
8 Installing the PCM Cables
8.1 Installing Cable in Cable Tray …………………………………………..20
8.2 Rack Side Connection ………………………………………………….20
8.2.1 Prepare the PCM Cables ………………………………………...20
8.2.2 Connect the Cables to the Rack ………………………………..21
8.2.3 L907/ 4 120 - Ohm Cable (Alcatel-Lucent Kits) ……………….21
8.2.4 FLEX3 / 4 - 75 Ohm Coaxial Cable (Alcatel-Lucent Kits) …....22
9 Installing the Antenna Jumpers
9.1 Antenna General Scheme ……………………………………………..23
9.2 Connection to the Feeder Termination ………………………………..24
9.3 Connection to the BTS Rack …………………………………………..24
10 Installing the Alarm Cables (Options)
10.1 Installing the Cables (Option) ………………………………………...25
10.2 Rack Side Connection ………………………………………………..26
11 Installing the Synchronization Cables (Option)
11.1 Configuration of Cabling ……………………………………………...28
11.2 Installation ………………………………………………………………29
12 Finishing Installation
12.1 Finishing Installation of the Metallic Sheath ……………………….29
12.2 Finishing ………………………………………………………………31
Appendix: Installation Pictures ………………………………………………..32
Appendix : Abbreviations ………………………………………………………37
4
COPYRIGHT © 2012 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
1. Preliminary Information
General information
The product specification and/or performance levels contained in this document are for
information purposes only and are subject to change without notice. They do not
represent any obligation on the part of Alcatel-Lucent.
Service Personnel Skill
Service Personnel must have an adequate technical background on telecommunications
and in particular on the equipment subject of this handbook.
An adequate background is required to properly install, operate and maintain
equipment. The fact of merely reading this handbook is considered as not enough.
Safety recommendation
The safety recommendations here below must be considered to avoid injuries on persons
and/or damage to the equipment:
Service Personnel
Installation and service must be carried out by authorized persons having appropriate
technical training and experience necessary to be aware of hazardous operations during
installation and service, so as to prevent any personal injury or danger to
other persons, as well as prevent damaging the equipment.
Access to the Equipment
Access to the Equipment in use must be restricted to Service Personnel only.
Safety Rules WWW.Alcatel-Lucent.com
Recommended safety rules are indicated in part (5-Safety , EMC, EMF, ESD Norms
and Equipment Labelling). Local safety regulations must be used if mandatory. Safety
instructions in this handbook should be used in addition to the local safety
regulations. In case of conflict between safety instructions stated in this manual and
those indicated in local regulations, mandatory local norms will prevail. Should not
local regulations be mandatory, then safety rules stated in this manual will prevail.
2. Scope
This Document aims to describe the hardware of 2G (9100 BTS DC Indoor Evolution)
3. Reference
5
4. Document Change History
Edition Number Reason and description of change Affected Page Effective date
WWW.Alcatel-Lucent.com
6
5.1 Hardware Description
Figure 1: Example of Mini DC Indoor 9100 BTS (Left) and Medi DC 9100 BTS (Right)
7
COPYRIGHT © 2012 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
5.1.2 Weight and Dimensions
8
COPYRIGHT © 2012 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
5.2 Final State
9
COPYRIGHT © 2012 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
6 Installing the Rack
Procedure: Remove the door (1) with its hinges (2) (See Figure 6)
Remove the two bars (4), (6) and the part (3)
Reverse the latch (5) and fix the two bars (4), (6) in the right place
Fix the door to the left side of the rack
Connect the earth link to the door and to the top left of the rack
Remove the reversed labelling (no Alcatel-Lucent labels) (See Figure 6)
Remove the orange line label.
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
0 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
6.3 Positioning the Rack
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
1 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
6.4.2 Fixing to the Concrete Floor
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
2 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
6.5.2 Fixing to the Raised Floor
Procedure: Insert the expanding plug 9 in the concrete floor (See Figure 12)
Screw in threaded rod 6 with washer 8 and nut 7
Screw coupling nut 5 as the figure shows
Screw in screw 1 with washer 2
Position bracket 3.
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
3 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
6.6.2 Fixing to the Wall
6.7 Preparing the Site Cable Tray and the Metal Sheath
Procedure: Make a cut-out in the cable way for the cables with metal sheath (See Figure 14)
Make a cut-out in the cable way for the antenna jumpers
Edge the cut-outs with edge protection
Fix provisory the metal sheath to the cable way (See Figure 15).
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
4 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
7 Installing the Power Supply Cables
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
5 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
7.2 Installing the Cables in the Cable Tray
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
6 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
Pass the GND cable through the metal sheath
Crimp an M8 wire terminal on the GND cable
Fit a rubber sleeve on the wire terminal
Connect the GND cable to the stud of the BTS (See Step 2)
At the site side, cut the cable and crimp a wire terminal on the GND cable (diameter depending
on site) (See Step 3)
Fit a rubber sleeve on the wire terminal
Connect the GND cable to the site earth plate (See Step 6).
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
7 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
Procedure: Pass the 48 V power cables through the metal sheath
Remove the rubber caps from the power supply terminals on the rack
Pass the cables into the rubber caps (See Steps 1 to 4)
Crimp M6 terminals on the cables
Fit a rubber sleeve on the wire terminal
Connect the 48 V cables to the studs of the BTS:
Black insulated conductor to the 0 V terminal
Blue insulated conductor to the - 48 V terminal
Fit the rubber caps on the power terminals.
Procedure: On the site side, cut the 48 V cables and crimp on a lug (diameter depending on site)
Fit a rubber sleeve on the terminal lug
Connect the 48 V cable to the site breakers
Label the 48 V cables and the site power box.
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
8 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
7.6 Power Supply Testing
Procedure: Check that all the rack breakers are switched off
At the rack, test for short circuit between 0 V and - 48 V
At power box, switch on the fuse breakers (See Figure 20)
At the rack, test the voltage polarity (See Figure 20)
At the power box, switch off the fuse breakers
1
COPYRIGHT © 2012 ALCATEL-LUCENT.
9 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
8.1 Installing Cable in Cable Tray
Procedure: Remove 2 cm of outer insulation near the metal sheath fixing point on each PCM cable (See
Figure 21)
Prepare the cable termination
Fit a rubber sleeve (4) (See Figure 22)
Label the cables (See Figure 22).
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
0 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
8.2.2 Connect the Cables to the Rack
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
1 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
Procedure: Remove the lightning protection block (2 in Figure 22)
Insert the wires in the terminal block (1 in Figure 22)(to avoid cutting problems os short
circuits, take the wire with the first hand and insert it with the other hand)
Fit the lightning protection block
Tie the cables to the rack (with adhesive tie blocks).
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
2 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
9 Installing the Antenna Jumpers
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
3 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
9.2 Connection to the Feeder Termination
Procedure: Lead the jumpers through the cut-outs in the cable tray
Ensure that hte bending radius of each cable is at least 3 cm
Use the plastic ties to bundle the cables together
Tighten with special tightening tool (See Tools catalogue).
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
4 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
10 Installing the Alarm Cables (Options)
1). Install the alarm cables in special compartment of cable tray (See Information Required
(Section 1.8) for the number of alarms to be installed)
2). Attach cables with plastic cable ties
3). Label the cables
4). Pass the alarm cables through the metal sheath
5). Fit a rubber sleeve on wire terminations.
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
5 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
10.2 Rack Side Connection
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
6 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
Procedure: Refer to Information Required (Section 1.8) in chapter 1 for the cable connections
and the quantity of alarms to be connected.
From the end of the sheathing, bundle the cables together and attach them with
cable ties.
Fit a rubber sleeve on wire terminations
Insert the wires into the connectors:
Connector (1) = input alarms 1 to 8 (See Figures 32 and 33)
Connector (2) = input alarms 9 to 16
Connector (3) = input alarms 17 to 24
Connector (4) = output alarms (not used)
Tie the cables to the rack
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
7 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
11 Installing the Synchronization Cables (Option)
11 .1 Configuration of Cabling
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
8 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
11.2 Installation
12 Finishing Installation
2
COPYRIGHT © 2012 ALCATEL-LUCENT.
9 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
Procedure: Stretch the metallic sheath between the vertical cutout in the cable tray
and the BTS rack (See Figure 39).
Fix the metallic sheath to the cable tray with one stove screw (See Figure 39).
Cut the metallic sheath to the right length (*1).
Fix a lug to the metallic sheath if necessary.
Connect the metallic sheath tot he rack (See Figure 40).
Tighten the stripped PCM cable shielding to the sheath using the metallic tie.
wrap provided in the kit (See Figure 40)..
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
0 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
12.2 Finishing
Procedure: Affix the “ BTS STATION “ and “ N “ labels to the door of the BTS
Clear away packaging
Leave the site tidy
Leave the BTS door key
Clean the site.
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
1 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
Pictorial Elaboration:
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
2 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
3 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
4 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
5 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
6 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
7 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
8 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
3
COPYRIGHT © 2012 ALCATEL-LUCENT.
9 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
4
COPYRIGHT © 2012 ALCATEL-LUCENT.
0 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
4
COPYRIGHT © 2012 ALCATEL-LUCENT.
1 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
Appendix : Abbreviations
4
COPYRIGHT © 2012 ALCATEL-LUCENT.
2 ALL RIGHTS RESERVED.
ALCATEL-LUCENT — INTERNAL PROPRIETARY — USE PURSUANT TO COMPANY INSTRUCTION
WWW.Alcatel-Lucent.com