Académique Documents
Professionnel Documents
Culture Documents
1. General description
The 74HC4852; 74HCT4852 are high-speed Si-gate CMOS devices and are specified in
compliance with JEDEC standard no. 7A.
With E LOW, two of the eight switches are selected (low impedance ON-state) by S0 and
S1. With E HIGH, all switches are in the high-impedance OFF-state, independent of S0
and S1.
The injection-current effect control allows signals at disabled analog input channels to
exceed the supply voltage without affecting the signal of the enabled analog channel. This
eliminates the need for external diode/resistor networks typically used to keep the analog
channel signals within the supply-voltage range.
2. Features
n Injection-current cross coupling < 1 mV/mA
n Wide supply voltage range from 2.0 V to 6.0 V for 74HC4852
n ESD protection:
u HBM JESD22-A114E exceeds 2000 V
u CDM JESD22-C101C exceeds 1000 V
n Latch-up performance exceeds 100 mA per JESD 78 Class II level A
n Low ON-state resistance:
u 400 Ω (typical) at VCC = 2.0 V
u 215 Ω (typical) at VCC = 3.0 V
u 120 Ω (typical) at VCC = 3.3 V
u 76 Ω (typical) at VCC = 4.5 V
u 59 Ω (typical) at VCC = 6.0 V
Nexperia 74HC4852; 74HCT4852
4-channel analog MUX/DEMUX with injection-current effect control
3. Applications
n Analog multiplexing and demultiplexing
n Digital multiplexing and demultiplexing
n Signal gating
n Automotive application
4. Ordering information
Table 1. Ordering information
Type number Package
Temperature range Name Description Version
74HC4852D −40 °C to +125 °C SO16 plastic small outline package; 16 leads; SOT109-1
body width 3.9 mm
74HC4852PW −40 °C to +125 °C TSSOP16 plastic thin shrink small outline package; 16 leads; SOT403-1
body width 4.4 mm
74HC4852BQ −40 °C to +125 °C DHVQFN16 plastic dual in-line compatible thermal enhanced very SOT763-1
thin quad flat package; no leads; 16 terminals;
body 2.5 × 3.5 × 0.85 mm
74HCT4852D −40 °C to +125 °C SO16 plastic small outline package; 16 leads; SOT109-1
body width 3.9 mm
74HCT4852PW −40 °C to +125 °C TSSOP16 plastic thin shrink small outline package; 16 leads; SOT403-1
body width 4.4 mm
74HCT4852BQ −40 °C to +125 °C DHVQFN16 plastic dual in-line compatible thermal enhanced very SOT763-1
thin quad flat package; no leads; 16 terminals;
body 2.5 × 3.5 × 0.85 mm
5. Functional diagram
10
0
0
4×
9 3
1
13
6
G4
1Z 1Y0 12
1Y1 14 MUX/DMUX
1
0
10 S0 1Y2 15 5
3 1
9 S1 1Y3 11 2
2
2Y0 1 4
3
2Y1 5 12
0
14
2Y2 2 13 1
15
6 E 2Y3 4 2
2Z
11
3
3 001aag093 001aag094
VCC
16
INJECTION 13
CURRENT 1Z
CONTROL
INJECTION 12
CURRENT 1Y0
CONTROL
INJECTION 14
CURRENT 1Y1
CONTROL
INJECTION 15
CURRENT 1Y2
10 CONTROL
S0
INJECTION 11
1-OF-4 CURRENT 1Y3
DECODER CONTROL
INJECTION 1
CURRENT 2Y0
9 CONTROL
S1
INJECTION 5
CURRENT 2Y1
CONTROL
INJECTION 2
CURRENT 2Y2
6 CONTROL
E
INJECTION 4
CURRENT 2Y3
CONTROL
INJECTION 3
CURRENT 2Z
CONTROL
GND
8 001aag095
6. Pinning information
6.1 Pinning
74HC4852 74HC4852
74HCT4852 74HCT4852
16 VCC
2Y0
2Y0 1 16 VCC terminal 1
index area
1
2Y2 2 15 1Y2
2Y2 2 15 1Y2
2Z 3 14 1Y1 2Z 3 14 1Y1
2Y3 4 13 1Z 2Y3 4 13 1Z
2Y1 5 12 1Y0
2Y1 5 12 1Y0
E 6 GND(1) 11 1Y3
E 6 11 1Y3
n.c. 7 10 S0
9
n.c. 7 10 S0
GND
S1
GND 8 9 S1 001aag097
7. Functional description
Table 3. Function table[1]
Input Channel ON
E S1 S0
L L L nY0 to nZ
L L H nY1 to nZ
L H L nY2 to nZ
L H H nY3 to nZ
H X X -
8. Limiting values
Table 4. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Min Max Unit
VCC supply voltage −0.5 +7.0 V
VI input voltage [1] −0.5 VCC + 0.5 V
VSW switch voltage [2] −0.5 VCC + 0.5 V
IIK input clamping current VI < −0.5 V or VI > VCC + 0.5 V - ±20 mA
ISK switch clamping current VSW < −0.5 V or VSW > VCC + 0.5 V - ±20 mA
ISW switch current VSW > −0.5 V or VSW < VCC + 0.5 V - ±25 mA
ICC supply current - 50 mA
IGND ground current −50 - mA
Tstg storage temperature −65 +150 °C
Ptot total power dissipation Tamb = −40 °C to +125 °C [3] - 500 mW
[1] The minimum and maximum input voltage rating may be exceeded if the input clamping current rating is observed.
[2] The minimum and maximum switch voltage rating may be exceeded if the switch clamping current rating is observed.
[3] For SO16 package: Ptot derates linearly with 8 mW/K above 70 °C.
For TSSOP16 package: Ptot derates linearly with 5.5 mW/K above 60 °C.
For DHVQFN16 packages: Ptot derates linearly with 4.5 mW/K above 60 °C.
VCC
VI
nZ
n.c.
VCC
VIH E VIL E
nYn nZ nYn
IS IS
any disabled channel
VI GND VO VO
GND
001aag098 001aag099
VCC
any disabled channel
VI(1) nYn
ISW
nZ
VSW
V
VIL E
VCC
E VI(2) nYn
VIL
selected channel(1)
nYn nZ RS
GND
VI GND ISW VI VO
001aag100 001aag101
see Figure 10
VCC = 2.0 V 2.2 9.3 33 2.2 34 2.2 35 ns
VCC = 3.0 V 2.2 4.9 16.5 1.9 18 1.9 19.5 ns
VCC = 3.3 V 2.0 4.4 15.0 1.6 16.5 1.6 18.5 ns
VCC = 4.5 V 1.6 3.2 11.6 1.1 12.5 1.1 13.5 ns
VCC = 6.0 V 1.5 2.5 10.2 0.9 11 0.9 12 ns
Sn to nZ, nYn; [1]
see Figure 11
VCC = 2.0 V 7.7 16.8 38 6.3 40 6.3 42 ns
VCC = 3.0 V 4.9 8.8 20 3.9 21.5 3.9 23 ns
VCC = 3.3 V 4.4 7.9 17.5 3.4 19 3.4 22 ns
VCC = 4.5 V 3.2 5.8 14 2.3 15 2.3 17 ns
VCC = 6.0 V 2.4 4.8 12.6 1.6 14.5 1.6 16.5 ns
ten enable time E to nZ, nYn; [2]
see Figure 12
VCC = 2.0 V 10.5 20.5 47.5 8.5 52.5 8.5 57.5 ns
VCC = 3.0 V 6.2 10.6 45 5.2 50 5.2 55 ns
VCC = 3.3 V 5.6 9.4 42.5 4.6 47.5 4.6 52.5 ns
VCC = 4.5 V 4.2 6.9 40 3 45 3 50 ns
VCC = 6.0 V 3.2 5.6 39 2.2 40 2.2 40 ns
tdis disable time E to nZ, nYn; [3]
see Figure 12
VCC = 2.0 V 39.5 75.4 100 39.3 105 39 115 ns
VCC = 3.0 V 35.2 69.5 90 35.5 100 35 110 ns
VCC = 3.3 V 34.6 68.1 85 34.6 95 34.5 105 ns
VCC = 4.5 V 28.5 63 80 28.2 90 28 100 ns
VCC = 6.0 V 14.4 57.9 78 13.5 80 13.0 80 ns
CPD power dissipation per channel; [4]
see Figure 10
VCC = 4.5 V 1.6 3.5 11.5 1.1 12.5 1.1 13.5 ns
Sn to nZ, nYn; [1]
see Figure 11
VCC = 4.5 V 3.2 7.6 13 2.3 15 1.6 17 ns
ten enable time E to nZ, nYn; [2]
see Figure 12
VCC = 4.5 V 4.2 8.3 25 3.0 30 3.0 35 ns
tdis disable time E to nZ, nYn; [3]
see Figure 12
VCC = 4.5 V 28.5 61.8 80 28.2 90 28.0 100 ns
CPD power dissipation per channel; [4]
12. Waveforms
VCC
nZ or nYn
0.5VCC
input
GND
tPLH tPHL
VCC
nYn or nZ 0.5VCC
output
GND
001aah578
Fig 10. Input (nZ, nYn) to output (nYn, nZ) propagation delays
VI
Sn input VM
GND
tPLH tPHL
VCC
nYn or nZ
VM
output
GND
001aah579
VI
E input VM VM
0V
tPLZ tPZL
VCC
nZ or nYn output VM
VX
VOL
tPHZ tPZH
VOH
VY
nZ or nYn output VM
GND
switch ON switch OFF switch ON
001aah580
VCC
selected
channel
nYn
G Sn
nZ
n.c.
E
nYn
disabled
channel
GND
001aah581
tW
VI
90 % 90 %
negative
pulse VM VM
10 %
0V
tf tr
tr tf
VI
90 %
positive
pulse VM VM
10 % 10 %
0V
tW
001aac221
switch VCC
VCC open
RL
VI VO
G DUT
RT CL
GND
001aaf883
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
D E A
X
y HE v M A
16 9
Q
A2
(A 3) A
A1
pin 1 index
θ
Lp
1 8 L
e w M detail X
bp
0 2.5 5 mm
scale
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
99-12-27
SOT109-1 076E07 MS-012
03-02-19
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1
D E A
X
y HE v M A
16 9
Q
A2 (A 3)
A
A1
pin 1 index
θ
Lp
L
1 8
detail X
w M
e bp
0 2.5 5 mm
scale
mm 1.1
0.15 0.95 0.30 0.2 5.1 4.5 6.6 0.75 0.4 0.40 8o
0.25 0.65 1 0.2 0.13 0.1 o
0.05 0.80 0.19 0.1 4.9 4.3 6.2 0.50 0.3 0.06 0
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
99-12-27
SOT403-1 MO-153
03-02-18
DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads;
16 terminals; body 2.5 x 3.5 x 0.85 mm SOT763-1
D B A
A
A1
E c
terminal 1 detail X
index area
terminal 1 C
e1
index area
e b v M C A B y1 C y
w M C
2 7
1 8
Eh e
16 9
15 10
Dh
X
0 2.5 5 mm
scale
DIMENSIONS (mm are the original dimensions)
A(1)
UNIT
max.
A1 b c D (1) Dh E (1) Eh e e1 L v w y y1
02-10-17
SOT763-1 --- MO-241 ---
03-01-27
14. Abbreviations
Table 12. Abbreviations
Acronym Description
CDM Charged Device Model
CMOS Complementary Metal Oxide Semiconductor
DUT Device Under Test
ESD ElectroStatic Discharge
HBM Human Body Model
MM Machine Model
[1] Please consult the most recently issued document before initiating or completing a design.
[2] The term ‘short data sheet’ is explained in section “Definitions”.
[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nexperia.com.
18. Contents
1 General description . . . . . . . . . . . . . . . . . . . . . . 1
2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4 Ordering information . . . . . . . . . . . . . . . . . . . . . 2
5 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
6 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4
6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
7 Functional description . . . . . . . . . . . . . . . . . . . 5
8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5
9 Recommended operating conditions. . . . . . . . 6
10 Static characteristics. . . . . . . . . . . . . . . . . . . . . 6
11 Dynamic characteristics . . . . . . . . . . . . . . . . . 10
12 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 15
14 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 18
15 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 18
16 Legal information. . . . . . . . . . . . . . . . . . . . . . . 19
16.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 19
16.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
16.3 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
16.4 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
17 Contact information. . . . . . . . . . . . . . . . . . . . . 19
18 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20