Académique Documents
Professionnel Documents
Culture Documents
PP 82DSP
P LU G & P L AY
8-Kanal Verstärker mit integriertem DSP
8-Channel Amplifier with integrated DSP
Congratulations!
Dear Customer,
Congratulations on your purchase of this high-qua- We wish you many hours of enjoyment with your
lity MATCH product. new MATCH PP 82DSP.
Yours,
With the PP 82DSP, MATCH is setting new stan-
AUDIOTEC FISCHER
dards in the evolving plug & play market.
General instructions
General installation instructions for MATCH General instruction for connecting the PP
components 82DSP amplifier
To prevent damage to the unit and possible injury, The PP 82DSP may only be installed in vehicles
read this manual carefully and follow all installati- which have a negative ground electrical system.
on instructions. This product has been checked for Any other system may cause damage to the
proper function prior to shipping and is guaranteed amplifier and the electrical system of the vehicle.
against manufacturing defects.
Use only the provided MATCH cable for con-
Before starting your installation, disconnect nection of the PP 82DSP. The use of other
the battery’s negative terminal to prevent cables can result in damage of the ampli-
damage to the unit, fire and/or risk of injury. For fier, the head unit / radio or the connected
a proper performance and to ensure full warranty loudspeakers!
coverage, we strongly recommend to get this pro-
duct installed by an authorized MATCH dealer. Prior to installation, plan the wire routing to
avoid any possible damage to the wire harness.
Install your PP 82DSP in a dry location with suf- All cabling should be protected against possible
ficient air circulation for proper cooling of the crushing or pinching hazards. Also avoid routing
equipment. The amplifier should be secured to cables close to potential noise sources such as
a solid mounting surface using proper mounting electric motors, high power accessories and other
hardware. Before mounting, carefully examine the vehicle harnesses.
area around and behind the proposed installati-
on location to insure that there are no electrical The fuse may only be replaced by an
cables or components, hydraulic brake lines or any identically rated fuse (2 x 25 A) to avoid damage
part of the fuel tank located behind the mounting of the amplifier.
surface. Failure to do so may result in unpredictable
damage to these components and possible costly
repairs to the vehicle.
13
Connectors and control units
1 2 3 4 5
6 7 8 9 10 11 12 13 14 15
MODE Switches
Switch no. 1 Switch no. 2 Amplifier overall gain Switch no. 6 remote control URC 2A
OFF OFF 0 dB OFF remote control deactivated
ON OFF - 4 dB ON remote control activated
OFF ON + 2 dB
Switch no. 5 Mode switch URC 2A
ON ON - 2 dB
Mode switch on remote control bypasses
OFF
Affects all eight output channels! MATCH sound optimization if pressed
Mode switch on tremote control activates AUX
ON input if pressed
Switch no. 3 Switch no. 4 Subwoofer gain MODE Switch no. 5 has no function if remote control is
OFF OFF 0 dB deactivated via MODE switch no.6
ON OFF - 4 dB
OFF ON + 2 dB Please note:
ON ON - 2 dB It is possible to deactivate / reactivate both Mode swit-
Only affects subwoofer channels! ches no.5 and 6 via the PC-tool software.
17
Unique Features of the PP 82DSP
18
Installation
The MATCH PP 82DSP must be connected to mm² / AWG 6 – 8! The ground cable (same gauge
the head unit (radio) as follows: as the +12V wire) should be connected to a com-
Caution: Carrying out the following steps will mon ground reference point (this is located where
require special tools and technical knowledge. In the negative terminal of the battery is grounded
order to avoid connection mistakes and/or dama- to the metal body of the vehicle), or to a prepared
ge, ask your dealer for assistance if you have any metal location on the vehicle chassis, i.e. an area
questions and follow all instructions in this manual which has been cleaned of all paint residues.
(see page 13).
4. Connect the MATCH harness to the MATCH PP
1. After removing the radio from the dash using 82DSP, see fig. 3 3 .
appropriate tools, disconnect the vehicle harness
from the radio. Next, connect the vehicle harness Optimizing the amplifier gain setting:
to the male connector of the MATCH cable harness, Turn on the car radio and the volume up gradually.
see fig. 3 1 Maximum volume has been reached when loud-
Depending on your car an additional car-specific speaker distortion becomes audible. To increase
adaptor may be required. volume range of the radio use the MODE switches
A list of all cars and the respective adaptors can be nos. 1 and 2 (refer to page 17) to reduce the overall
found on www.audiotec-fischer.com. gain of the PP 82DSP. If your radio is at maximum
volume without any distortion being audible, you
2. Connect the female connector of the MATCH can use the MODE switches to increase the am-
cable harness or the car-specific adaptor to the ra- plifier overall gain by +2 dB. Be careful when using
dio, see fig. 3 2 . this function.
19
Abb. 3 Connection of the amplifier to the car radio
5
3 Female
4 connector for
original cable
harness
2
1 Male and female con-
nector for original cable
harness or car-specific
adaptor
1 The ISO female connector will either be plugged into the vehicle harness that has been dis-
connected from the car radio or a car-specific adaptor.
2 The ISO male connector will either be plugged into the car radio or into a car-specific adaptor.
3 The 20-pole connector will be plugged into the MATCH PP 82DSP amplifier.
4 The power supply terminal has to be connected directly with the battery - use only adequate
cables and fuse the +12V wire close to the battery.
5 Optional: car-specific adaptor – such an adaptor may be required if the ISO connectors of
the provided PP 82DSP cable harness does not fit into your car radio.
20
Connection to a PC
It is possible to freely configure the PP 82DSP with To install the software follow the next steps:
our DSP PC-tool software. The user interface is de-
signed for easy handling of all functions and allows 1. Download the PC-tool software from the web-
to individually adjust all eight DSP channels. site www.audiotec-fischer.com
2. Install the software on your computer. During
Prior to connecting the amplifier to your PC, visit our that process the required USB driver will be au-
website and download the latest version of the PC- tomatically installed as well.
tool software. Check from time to time for software 3. After the software installation processed is
updates in order so that your amplifier is always up- completed you can now connect the amplifier to
to-date. your PC using the provided USB cable.
You will find the software and the respective user 4. Turn the amplifier on and then start the soft-
manual on www.audiotec-fischer.com. ware. If the firmware of the amplifier is not the
We strongly recommend to carefully read the user latest version it will automatically be updated on
manual before using the software for the first time in the currently selected memory position.
order to avoid any complications and failures. 5. You are now ready to configure the PP 82DSP
Make sure that the amplifier is not connected to according to your demands.
your computer before the software and USB driver
is installed!
Device
configuration
Channel
Channel
selection
configuration
Frequency
graph Output
level
EQ fine
Equalizer
adjustment
21
Configuration examples
This is a classical 5-channel setup, where 4 of the 8 amplifier channels are used to drive a MATCH
subwoofer. We strongly recommend to use this configuration only in combination with our subs PP 10E-D
or PP 8E-Q. The versions PP 7E-D and PP 7S-D may not be able to handle the full amount of amplifier
power.
Front 2-way full active system / Rear passive system plus subwoofer
Front tweeters
Front midbass /
rear speakers
This 7-channel configuration is recommended for highest quality in combination where the typical passive
crossover for the front midbass/tweeter is eliminated and those speakers are driven by separate amplifier
channels. The PC tool software offers a wide range of highpass/lowpass filters for precise crossover
design.
22
Technical Data
Warranty Disclaimer
The limited warranty comply with legal regulations. For damages on the vehicle and the device, caused
Failures or damages caused by overload or impro- by handling errors of the device, we can’t assume
per use are not covered by the warranty. liability.
Please return the defective product only with a All MATCH amplifiers are tagged with a E-Certifi-
valid proof of purchase and a detailed malfunction cation number and also a CE-Certification mark.
description. Thereby these devices are ceritified for a use
Technical specifications are subject to change! inside vehicles inside the European Union (EU).
Errors are reserved!
23
Audiotec Fischer GmbH
Gewerbegebiet Lake II · Hünegräben 26 · D-57392 Schmallenberg
Tel.: +49 2972 9788 0 · Fax: +49 2972 9788 88
E-mail: match@audiotec-fischer.com · Internet: www.audiotec-fischer.com