Académique Documents
Professionnel Documents
Culture Documents
ANSWER: C
QUESTION 2
The optimum pressure to achieve 100% efficiency in
abrasive blast cleaning is?
A) 75 psi
B) 450 psi
C) 100 psi
D) 220 psi
ANSWER: C
QUESTION 3
Sand is not permitted as a dry blast abrasive, as
directed by:
A) BGC/PS/PA10
B) BS 7079 Part A
C) COSHH
D) BS 410
ANSWER: C
QUESTION 4
How many times can Garnet be used as an abrasive
for BGas site use?
ANSWER: C
QUESTION 5
The correct ratio of a “working mix” would be:
A) 70-
70-80% Grit : 20-
20-30% Shot
B) 50% Grit :50% Shot
C) 70-
70-80% Shot : 20-
20-30% Grit
D) 20-
20-25% Sand : 75-
75-80% Copper Slag
ANSWER: C
QUESTION 6
Flame cleaning uses which mechanisms?
ANSWER: C
QUESTION 7
Carbon Impregnated hoses are used to:
ANSWER: D
QUESTION 8
One of the most important safety items of equipment in
abrasive blasting is:
ANSWER: C
QUESTION 9
What is the approximate speed of the abrasive particles
exiting a wheelabrator?
A) 450 mph
B) 220 mph
C) Mach 3
D) 100 psi
ANSWER: B
QUESTION 10
Where would you normally use a comparator gauge?
ANSWER: B
QUESTION 11
“Amplitude” refers to what?
A) The ‘peak-
‘peak-to
to--trough’ height of a blast profile
B) The amount of noise a blasting operation creates
C) the velocity of the abrasive particles
D) the roughness of an abrasive particle
ANSWER: A
QUESTION 12
What is the material used in surface replica tape,
used to measure profile?
A) Mylex
B) Testrex
C) Mylar
D) Mylon
ANSWER: C
QUESTION 13
How do we remove hygroscopic salts from the substrate:
A) Water blasting
B) Silver nitrate
C) Dry abrasive blast cleaning
D) Chalk or Talc
ANSWER: A
QUESTION 14
The test for the presence of Hygroscopic Salts, is:
ANSWER: A
QUESTION 15
How many photographs of flame cleaning standards are
shown in BS 7079 Part A?
A) 4
B) 14
C) 8
D) 16
ANSWER: A
QUESTION 16
Which abrasive has the effect of stress relieving the
substrate?
A) Copper Slag
B) Metallic Shot
C) Steel Grit
D) Garnet
ANSWER: C
QUESTION 17
Where would it be advisable to use Steel Grit as an
abrasive?
ANSWER: C
QUESTION 18
What is the minimum number of readings required for a
Dial Micrometer?
A) Minimum of 10
B) Minimum of 12
C) One only
D) As many as you wish, but the average reading is
recorded
ANSWER: C
QUESTION 19
Which test would be used to determine for soluble salts in
a marine environment?
A) Potassium Hexacyanoferrate
B) Copper Sulphate
C) Iron Phosphate
D) Silver Nitrate
ANSWER: D
QUESTION 20
The standard for the test sieves used for the sizing of
abrasives is:
A) BS 7079 Part A
B) BS 410
C) BGC / PS / PA10
D) SI 1657
ANSWER: B
QUESTION 21
The most common type of abrasive used for BGas
site work is:
A) Copper Slag
B) Grit & Shot mix
C) Garnet
D) Metallic Shot
ANSWER: A
QUESTION 22
Compared to a Venturi Nozzle, a Straight Bore
Nozzle would give:
ANSWER: D
QUESTION 23
Anchor Pattern, Key, Peak-
Peak-to
to--trough, are names given
to what?
ANSWER: B
QUESTION 24
What is a “knock out pot”?
A) A drum used for mixing paint and thinners
B) The area on the equipment where static electricity
can build up and be hazardous
C) A vessel for removing oil and moisture from the air
stream
D) A container where any blockages of the nozzle can
be tapped free
ANSWER: C
QUESTION 25
High Pressure blasting operates up to which pressure?
A) 100 psi
B) 450 psi
C) 30,000 psi
D) 2,250 mph
ANSWER: C