Vous êtes sur la page 1sur 25

GEARLESS DRIVE MOTOR FROM SIEMENS

• Picture documentation about the Motor installation at jobsite

Copyright Siemens AG 2004. All Rights Reserved.


Shipping and Transportation

• Transportation of the stator-segments from the port-site to the job-site


• The number of segments for each SAG-Mill Motor is usually 4 units

Copyright Siemens AG 2004. All Rights Reserved.


Shipping and Transportation

• Transportation of the pole segments from the port-site to the


job-site

Copyright Siemens AG 2004. All Rights Reserved.


Stator segments installation

• Lift ant turn the bottom stator segments with 2 cranes for installation
on the basement

Copyright Siemens AG 2004. All Rights Reserved.


Stator segments installation

• Lift ant turn the bottom stator segments with 2 cranes for installation
on the basement
• Lift ant turn the top stator segments and install on the bottom
segments

Copyright Siemens AG 2004. All Rights Reserved.


Stator segments installation

• Lift ant turn the top stator segments and install on the bottom
segments
• Installation of the third segment

Copyright Siemens AG 2004. All Rights Reserved.


Stator segments installation

• Lift ant turn the top stator segments and install on the bottom
segments
• Install the last stator segment

Copyright Siemens AG 2004. All Rights Reserved.


Stator segments installation

• Lay out the lamination package between the stator segments in way of
the winding core

Copyright Siemens AG 2004. All Rights Reserved.


Stator segments installation

• View after the installation of all 4 stator segments


(the ring is completed „Ringmotor“)

Copyright Siemens AG 2004. All Rights Reserved.


Winding installation

• Install the windings in way of the stator core joints


Rotor (pole segments) installation

• Lift the pole segments sequencly and install to


the mill flange (each pole segments hold 4 poles)

Copyright Siemens AG 2004. All Rights Reserved.


Rotor (pole segments) installation

• Lift the pole segments sequencly and install to


the mill flange (each pole segments hold 4 poles)

Copyright Siemens AG 2004. All Rights Reserved.


Rotor (pole segments) installation

• Lift the pole segments sequencly and install to


the mill flange (each pole segments hold 4 poles)
• The mill is temporary turned with 2 turning gears

Copyright Siemens AG 2004. All Rights Reserved.


Rotor (pole segments) installation

• Tools for the pole segments installation


• Hydraulic bolt stretcher unit

Copyright Siemens AG 2004. All Rights Reserved.


Slip ring installation

• Mount and lift the slipring segments with the


prepared lifting device

Copyright Siemens AG 2004. All Rights Reserved.


Slip ring installation

• Mount all slipring segments (7 pieces) and carry


out alignments

Copyright Siemens AG 2004. All Rights Reserved.


Seal ring installation

• Mount all sealring segments (7 pieces) and carry


out alignments

Copyright Siemens AG 2004. All Rights Reserved.


Speed control and instrumentation

• Mount all speed control segments (41 segments)


and instrumentation

Copyright Siemens AG 2004. All Rights Reserved.


Speed control and instrumentation

• Mout all speed control segments and


instrumentation

Copyright Siemens AG 2004. All Rights Reserved.


Cooling System installation

• Cooler installation

Copyright Siemens AG 2004. All Rights Reserved.


Cooling System installation

• Cooler installation

Copyright Siemens AG 2004. All Rights Reserved.


Winding cover installation

• Mount all the winding covers

Copyright Siemens AG 2004. All Rights Reserved.


Winding cover installation

• Mount all the winding and inspection covers

Copyright Siemens AG 2004. All Rights Reserved.


Termination cubicles

• Mount terminal and auxillary cubicels

Copyright Siemens AG 2004. All Rights Reserved.


Stator and Rotor

• Picture shows the motor shortly before moving


the stator over the rotor.

Copyright Siemens AG 2004. All Rights Reserved.

Vous aimerez peut-être aussi