Académique Documents
Professionnel Documents
Culture Documents
for
TURNING
1 w w w. p r a m e t . c o m
new grades for turning
area of focus
T5305
WEAR RESISTANCE
T5315
T9310
T9315
T9325
T8310 T9335
T8315
T7335
T8330
T8345
TOUGHNES
2 w w w. p r a m e t . c o m
new grades for turning
T9310
T9310 - substrate
P
01-15
K H
05-20 10-20
3 w w w. p r a m e t . c o m
NEW GRADE WITH MT-CVD COATING
T9315
05-25
T9315 P
05-25 10-20
K H
• New material of generation T9300 characterized by
high wear resistance with considerable toughness
• Functional gradient substrate with relatively low
content of cobalt binder phase
• Thick MT-CVD coating with unique Al2O3 top
layer warrants extra-ordinary thermal, chemical
stability and protection of substrate
• Special final treatment after coating
• Machining of material group P, conditionaly K, H
• Finishing, continuous and modesty interrupted cut
• High stability of cutting edge
• High and moderate cutting speed
4 w w w. p r a m e t . c o m
NEW GRADE WITH MT-CVD COATING
T9325
15-35 10-30
T9325
15-35 15-25
P M K S
• The most versatile grade of new generation T9300
• Functional gradient substrate with moderate
content of cobalt binder phase
• Medium thick MT-CVD coating with unique
Al2O3 top layer warrants extra-ordinary thermal
and chemical stability and protection of substrate
• Special final treatment after coating
• Machining of material group P, M conditionaly
K,S
• Versatile application
• Unfavourable cutting conditions, continuous
and/or interrupted cut
• Medium and higher cutting speed
5 w w w. p r a m e t . c o m
new grades for turning
T9335
T9335 - substrate
P
20-45
M S
15-40 15-25
6 w w w. p r a m e t . c o m
new grades for turning
T7335
T7335 - substrate
M P S
20-40 20-40 15-25
7 w w w. p r a m e t . c o m
Application area
T9310 P KH
01-15 05-20 10-20
T9315 P K H
05-25 05-25 10-20
T9325 P MK
15-35 10-30. 15-35
S
15-25
T7335 P
20-40
M 20-40
S
15-25
T9335 P M S
20-45 15-40 15-25
FGM
8 w w w. p r a m e t . c o m
Coating
Adhesion Ti(O,C,N)
T9310 T9315
Wear Resistence Ti(C,N)
Adhesion Ti(N)
Toughness Substrate
T9325 T9335
9 w w w. p r a m e t . c o m
Application area
T5305 P K H
05-15 01-15 15-20
T5315 P M K H
10-25 05-15 10-25 15-25
WC+Co
10 w w w. p r a m e t . c o m
GRADES PRAMET TOOLS
označení
designation
struktura
microstructure aplikační oblast
aplication area Grade description and recommended
popis application
T5315 T5305
11 w w w. p r a m e t . c o m
NEW GRADES FOR TURNING
Substrate
T5305 T5315
fine-grained structure fine-grained structure T9315….
12 w w w. p r a m e t . c o m
GRADES PRAMET TOOLS
T5305 – new member in UPGRADE family
the most wear resistant grade aimed for cast iron turning,
new fine-grained substrate with low content of cobalt,
thick MTCVD coating with modern Al2O3 outer layer,
special treatment after coating,
suitable for machining of materials group K, H and P,
peak performance in gray cast irons,
high cutting speeds,
continuous and moderately interrupted cuts,
lunching date on 1st of April 2014.
13 w w w. p r a m e t . c o m
GRADES PRAMET TOOLS
T5315 – new member in UPGRADE family
universal grade aimed for both grey and ductile cast irons turning,
fine-grained substrate with adapted cobalt content,
thick MTCVD coating combining advantages of TiCN and Al2O3 layers,
special treatment after coating,
suitable for machining of materials group K, H, P and M,
for finishing up to roughing,
medium to high cutting speeds,
good for continuous and interrupted cuts,
lunching date on 1st of April 2014.
14 w w w. p r a m e t . c o m
NEW GRADE WITH PVD COATING
T8315
05-20 05-25 05-25 05-15
T8315 M N K H 05-20
P S
05-15
T8330 M P
20-35 15-30 15-25 15-25
N K S H
• The most universal of T8300
generation
• Submicron substrate with relatively
high cobalt content
• Nanostructured gradient PVD coating
• Increased hardness while decreased
internal stress
• Improved resistance against notch
wear
• Medium cutting speeds
• Suitable for machining of materials
group M, P, K, conditionally N, S, H
• Less favourable cutting conditions
16 w w w. p r a m e t . c o m
NEW GRADE WITH PVD COATING
T8345
20-40 20-30
T8345
30-50 20-40
M S P K
• The most tough of T8300 generation
• Submicron substrate with high cobalt
content
• Nanostructured gradient PVD coating
• Increased hardness while decreased
internal stress
• Improved resistance against notch wear
• Medium to lower cutting speeds
• Medium to bigger chip cross section
• Suitable for machining of materials group
M, S, conditionally P, K
• Unstable cutting conditions
17 w w w. p r a m e t . c o m
NEW GRADES FOR TURNING
Application area
T8310 M S N H
01-15 01-15 01-48 04-15
T8315 M K N H P S
05-20 05-25 05-25 05-15 05-20 05-15
T8330 M P K N S H
20-35 25-40 20-35 15-30 15-25 15-25
T8345 M S P K
20-40 20-30 30-50 20-40
18 w w w. p r a m e t . c o m
TECHNICAL DETAILS
SUBSTRATE
19 w w w. p r a m e t . c o m
GRADES PRAMET TOOLS
označení
designation
struktura
microstructure aplikační oblast
aplication area Grade description and recommended
popis application
T0315
20 w w w. p r a m e t . c o m
GRADES PRAMET TOOLS
označení
Designat microstructure
struktura aplication area
aplikační oblast Grade description and recommended
popis application
ion
21 w w w. p r a m e t . c o m
OTHER CUTTING MATERIALS
TT010 P M CERMETS
01-10 01-10
TT310 P M
10-25 15-25
D720 N PCD
05-20
TB310 H CBN
05-20
TC100 K H S
05-15 05-20 01-05
CERAMICS
SN100 K
05-15
22 w w w. p r a m e t . c o m
GRADES
for
MILLING
23 w w w. p r a m e t . c o m
MILLING GRADES
M5315
WEAR RESISTANCE
M9315
M9325 M9340
8215
8026
8230
8240new
S26
S45 P P
CVD PVD
TOUGHNESS
24 w w w. p r a m e t . c o m
MILLING GRADES FOR GENERAL MILLING
označení
designation
struktura
microstructure aplikační oblast
aplication area Grade description and recommended
popis application
25 w w w. p r a m e t . c o m
GRADES FOR COPY MILLING
označení
designation
struktura
microstructure aplikační oblast
aplication area Grade description and recommended
popis application
- fine grained substrate without cubical carbides with very low content of
cobalt
7010
26 w w w. p r a m e t . c o m
GRADES FOR COPY MILLING
označení
designation
struktura
microstructure aplikační oblast
aplication area Grade description and recommended
popis application
skupina
05 15 25 35 45
obráběných
materiálů - Ultra submicron substrate without cubical carbides (type H)
01 10 20 30 40 50 with very low content of cobalt.
H
K
N
S
P
7205
skupina
obráběných
05 15 25 35 45 materiálů
M
K
N
H
P
S
7215
content of cobalt.
- New gradient PVD coating.
- Unique slide properties.
- Medium up to higher cutting speed and lower up to medium chip
cross-section.
- Higher resistance against oxidation.
- Stable working conditions.
- Applicable on all material groups.
skupina
obráběných
05 15 25 35 45 materiálů
H
P
S
7230
27 w w w. p r a m e t . c o m
NEW GRADES FOR COPY MILLING
M8310 H P K S
05-15 01-10 01-10 01-10
M
01-10
M8325
P KM
20-30 20-35 15-30
M8345
P M S
30-50 30-40. 30-40
28 w w w. p r a m e t . c o m
UNCOATED GRADES
označení
designation
struktura
microstructure aplikační oblast
aplication area Grade description and recommended
popis application
HF7
29 w w w. p r a m e t . c o m
MT CVD grades for milling – REPLACING OF OLD GRADES
2215
M5315
5026
M9315 2230
M9325
M9340
TOUGHNESS
30 w w w. p r a m e t . c o m
APLICATION AREA
o M5315 K H P
10-30 10-20
o M9315 P K H
05-25 10-30 10-20
o M9325 P M S
10-30 10-25 05-15
o M9340 M P S
31 w w w. p r a m e t . c o m
NEW MT-CVD MILLING
10-30 GRADES
M5315
32 w w w. p r a m e t . c o m
NEW MT-CVD MILLING
05-25 GRADES
M5315
M9315 P 10-30
K H
10-20
M9325 P 10-25
M S
05-15
34 w w w. p r a m e t . c o m
NEW GRADE WITH MT-CVD COATING
M9340
30-40
M9340 M
35-50 20-30
P S
The most toughness grade from M9300 line
35 w w w. p r a m e t . c o m
PRAMET
GRADES
for
DRILLING
36 w w w. p r a m e t . c o m
drilling grade
20 Workpiece
Material Group
19 05 15 25 35 45
substrate „H“ 18
17 01 10 20 30 40 50
P M K N S H
16
15
grain 14
0,6-1,2 13
[m] 12
11
10
09
%Co 13,0 08
07
06
05
04 Nano-vrstevný
povlakTiN/TiAlN
% c.c. 0,65 03
gradientnívrstva
02 tloušťka 5,5 – 6,5 um
01
37 w w w. p r a m e t . c o m
drilling grade
D8330
+ optimal material for peripheral inserts
+ the first choice for unstable cutting
conditions
+ high universatility (P, M, K, S, H)
20 Workpiece
Material Group
19 05 15 25 35 45
substrate „H“ 18
17 01 10 20 30 40 50
P M K N S H
16
15
grain 14
0,6-1,2 13
[m] 12
11
10
09
%Co 10,0 08
07
06
05
04 Nano-vrstevný
povlakTiN/TiAlN
% c.c. 0,5 03
gradientnívrstva
02 tloušťka 5,5 – 6,5 um
01
38 w w w. p r a m e t . c o m
drilling grade
39 w w w. p r a m e t . c o m
www.pramet.com
40 w w w. p r a m e t . c o m