Académique Documents
Professionnel Documents
Culture Documents
7SR45 Self Powered/Dual Powered Non-Directional Overcurrent and Earth Fault Relay
Energy Management
7SR45 Argus
7SR45 Argus Self Powered/Dual Powered Non-Directional Overcurrent and Earth Fault Relay
Features
Password Protection
Self Monitoring
Trip Timers
Healthy shut-down below operating ranges
Remote reset (binary input based) of flag with/without
CT power and Auxiliary power
Two Settings Groups
User Interface
Functional Diagram 10
Long Time Inverse
50LC/ 50
51
SOTF (x2)
IL1 1
Very Inverse
(IA)
50LC/ 50
51
IL2 SOTF (x2)
Extremely Inverse
(IB)
50LC/ 50 0.1
51
SOTF (x2) 1 2 3 4 5 6 8
10 20 30 40 50 60 80
100
IL3
Current (multiples of setting)
(IC)
Fig 2. IEC Overcurrent Curves
50N
51N
(x2)
IL4
(IG) 50G
51G
(x2)
100
Time
(sec)
10
NOTE:
Moderately Inverse Multi-phase faults will result in shorter operating time.
1
Very Inverse
Sensitivity
In the absence of auxiliary voltage, the sensitivity of the
Extremely Inverse
relay is the minimum phase current required for the relay to
energize, detect a fault and trip as per the configuration.
0.1
1 2 3 4 5 6 8
10 20 30 40 50 60 80
100 The sensitivity of 7SR45 Argus Self Powered/Dual Powered
Current (multiples of setting) Non-Directional Overcurrent and Earth Fault Relay is 20% of
Fig 3. ANSI Overcurrent Curves nominal current for single phase and 13% of nominal current
in three phases. The PROTECTION HEALTHY LED and TRIP
50LC/SOTF READY LED TURN ON when the relay is TRIP ready at the
SOTF functionality provides high speed tripping if a fault is above mentioned current levels.
still present on the feeder after the reclosure of the circuit
breaker (Close-on-to-Fault) or if earthing clamps are left The following graphs show the sensitivity of the relay and
connected after maintenance. corresponding operating time for different start up currents.
RS485
RS485 Screened Rear Screened Rear
twisted pair terminals twisted pair terminals
Fig 7. Sensitivity for Single Phase Fault with Pulse Output Construction
NOTE:
The relay is housed in a non draw-out 4U high, size 4 case.
Multi-phase current will improve the sensitivity.
The rear connection comprises of user friendly pluggable
type terminals for pulse and flag output, binary inputs,
Data Acquisition - binary outputs, RS485 communication and auxiliary input.
Via Communication Interface The CT terminals are suitable for ring type lug connection to
provide a secure and reliable termination.
The front port can be switched off or set to use either the
Modbus RTU or IEC 60870-5-103 protocols for testing
purposes.
Minimum phase 20% of nominal current in single Quantity 3 x Phase and 1 x Earth
current for relay phase
Rated Current (In) 1 A or 5 A (ordering option)
operation 13% of nominal current in three
phases Measuring Range 0.2xIn to 20xIn
Instrumentation ± 5% (Typical)
Mechanical Specifications (≥0.13xIn to 2xIn)
± 3%
Design Panel mounting, Non draw-out (> 2xIn to 20xIn)
Polycarbonate moulded case
Frequency 50 Hz (Range: 45 Hz to 55 Hz)
Enclosure IP 52 (front panel)
IP 40 (enclosure sides) 60 Hz (Range: 54 Hz to 66 Hz)
IP 20 (rear side) Rated CT Burden ≤ 2.5 VA per phase and ≤ 0.2 VA
Depth is 203 mm (measured at Nominal earth for 1 A CT input
Weight 1.97 kgs (appx) Currents ≤ 3.0 VA per phase and ≤ 0.2 VA
(1 A and 5 A)) earth for 5 A CT input
7SR4501/7SR4502 Argus Self/Dual Powered Relay
Recommended Terminal Lugs Specifications Binary Inputs
IEEE/ANSI ± 5% or ± 50 ms
Follower Delay 0.00, 0.01... 20 s
Reset IEC/ANSI decaying, 0, 1... 60 s
Inhibited by Binary Input
50LC/SOTF (Switch-On-To-Fault)
156
149
185
168
12.5 188 30
204
30 mm clearance for
Terminal wiring
4.5 - 4 Holes
98.5
10.25 78
4.5
Current
Additional Inputs
Binary Inputs
Binary inputs,
Rear Binary outputs,
Communication Flag output,
port Pulse output
Additional
Binary
outputs
Auxiliary
Power Supply
168
159
X2
NO 1 IL2
COM 2 BO 1
4
NC 3
1A/5A 5
4
BO 2
5
6
IL3
6
X3
-ve 1A/5A 7
1
+ve PO
2
IL4
GND 8
NOTES:
Items shown in BOLD are ordering options
NO 6
COM IL2
7 BO 1
NC 8
4
9 1A/5A
BO 2 5
10
11 IL3
12
6
+ve
13 1A/5A 7
-ve PO
14
IL4
+ve
15
GND -ve FO 8
16
NOTES:
Items shown in BOLD are ordering options
Figure 19 Terminal Diagram of Self Powered (7SR4501-xGB10-1AA0) Non-Directional Overcurrent and
Earth Fault Relay with Flag
4 - ve BI2 2
1A/5A 7SR4501-1HB20-1AA0
5 3
X4 NO 6
9
3
GND BO2 1A/5A 5
10
4 B/-
11
IL3
12
6
13 + ve
X3 1A/5A
- ve PO 7
14
1 L
N IL4
2
15
+ ve
3
E GND - ve FO
16 8
NOTES:
Items shown in BOLD are ordering options
X4 X6 NO 6
NC 3
9
3
GND 4
BO2 1A/5A 5
10
4 B/- BO 4
5
11
IL3
12
6
13 + ve
X3 1A/5A
- ve PO 7
14
1 L
N IL4
2
15
+ ve
3
E GND - ve FO
16 8
NOTES:
Items shown in BOLD are ordering options
1 2 3 4 5 6 7 - 8 9 10 11 12 - 13 14 15 16
7SR45 Argus 7 S R 4 5 0 - 0 - 1 A A 0
Nondirec-
tional Over-
current and
Earth Fault
Relay
Size 4 Moulded Case, 4 CT1), 4 BI/4 BO, pulse output, 9 LEDs 2 H/J
Measuring Input
1 A, 50/60Hz 1
5 A, 50/60Hz 2
Auxiliary Voltage
Self Powered (CT Powered : BI Threshold 19V DC) G 1
Dual powered (CT Powered + Aux. Powered : 24-60 V DC, BI threshold 19 V DC) H 2
Dual powered (CT Powered + Aux. Powered : 60-240V AC/DC, BI threshold 88V AC/DC) J 2
Front Fascia
Standard Version A
Standard Version - with Trip Flag Indicator B
Communication Options
Front port : USB 1
Front Port : USB and Rear Port : RS-485 supporting
IEC 60870-5-103 and Modbus RTU (user selectable setting) 2
Additional functionality
No additional functionality A
Use the following ordering information to order 7SR45 Argus Self Powered/Dual Powered Non-Directional Overcurrent and
Earth Fault Relay battery spares.
Variants Description
7XG1900-1AA00-1000 Main Battery CR123A
EMEA-C10020-00-76GB
April 2018
www. siemens.com/energy