Vous êtes sur la page 1sur 36

Order No.

ITD1203903GE

Ver. 1.0

Pravin Mevada
Model No. LCD-2012-ET5series

Pravin Mevada

Troubleshooting Flowchart
Start up operation
c Panasonic Corporation 2012
Unauthorized copying and distribution is
a violation of law.

1
INDEX Pravin Mevada

1. Trouble Shooting SOS protection circuit


2. Stand by /Start up operation
3. Video/Audio Signal processing
4. 3D Method

2
1. Trouble Shooting SOS protection circuit

Pravin Mevada

3
1.Trouble Shooting SOS protection circuit (1)
Board Layout ( TC – L42ET5 )

P4 P2

A02
A
A12
P TC02A

GK4 TC01A
A20
GK A10
AC input

WiFi Module

K10
K
(under metal)

Board Name Function


A-Board Main Board

K-Board Remote Receiver, LED, Cat's eye


P-Board Power supply
GK-Board Power switch, Key

4
1.Trouble Shooting SOS protection circuit (2)

LED blinks Detail error Board may defect

No light No voltage STB5V detected P/A


1 LED driver: BL_SOS Panel/A/P
Fast 3 Incomplete or interrupted Boot Program execution of P/A
PEAKS IC8000 ( No P15V voltage)
7 No voltage SUB3.3V detected A
9 Audio amplifier: SOUND_SOS A/Speaker
10 No voltage PNL12V detected A/Panel
LED keeps Over voltage protection P/A
standby mode

5
1.Trouble Shooting SOS protection circuit (3) 1 time LED blink

LED blinks Detail error Board may defect

1 LED driver: BL_SOS Panel/A/P

BL_SOS is generated by backlight power board and sent to IC8000 of A board via connector P4
at pin 3 (or connector P2 at pin 11) when detecting malfunction of LED driver.
- Normal: BL_ON is high (3.3V) , BL_SOS is low (0V)
- Error : BL_ON is low (0V) , BL_SOS is high (3.3V)

Power on. Check if Yes Yes


(24V) Power on. Check if 3.3V (3.3V)
voltage 24V at pin 7-8-9
voltage (BL_ON) at pin2 of Panel Module
of P4 connector before
P4 before LED blinks?
LED blinks?

No No

P board A board

Panel Module
CN2 P4 P P2 A02 A
PWM_50
LEFT SIDE V 1 7
---------------------- 24V
2 8 Q7402
LED Backlight
BACKLIGHT PWM_50 power
3 9
BL_ON BL_ON IC8000
--------------------- V (LED driver)
RIGHT SIDE
12 2 11 6 Peaks
BL_SOS BL_SOS
11 3 10 4

6
1.Trouble Shooting SOS protection circuit (4) 3 time LED blink

LED blinks Detail error Board may defect

Fast 3 PEAKS IC does not wake up (no P15V voltage) P/A

P15V is supplied from P board. If the P15V is not available LED blinks 3 times (quick blink).

Power on.
No Remove P2 connector. No
Check if voltage P15V at
Check if short-circuit at
pin 1-3-5 of A02 P board
pin 1-3-5 of A02
connector before LED
connector?
blinks?
Yes
Yes
A board
A board
Also check if open-circuit the
Fuse PA7402. If it is opened
replace also P board.
A
IC5000
( reverse side of P board )
ANALOG
P ASIC

P2 P2 A02
PA 7402 1 P15V 1
Q7403 2 3 IC4900
Q7403 FUSE 3 5 AUDIO AMP
PA7402

7
1.Trouble Shooting SOS protection circuit (5) 7 time LED blink

LED blinks Detail error Board may defect

7 No voltage SUB3.3V detected A

SUB3.3V is regulated by IC5400 from P15V. SUB3.3V is only available as long as DCDCEN
signal (sent from IC5000) goes high.
If the voltage SUB3.3V is not detected by IC8000, the LED indicator will blink 7 times. This
voltage is only available when IC5400 is activated by DCDCEN command sent from IC5000.

IN THIS CASE, A BOARD DEFECTS ONLY

SUB1.8V
A
TU6706 IC8702

IC8902
A02
IC8900
1 IC8000
P15V SUB3.3V SUB3.3V_SENSE ASIC
FROM P BOARD
3 IC5400
5 IC5000
DCDCEN
ASIC

8
1.Trouble Shooting SOS protection circuit (6) 9 time LED blink

LED blinks Detail error Board may defect

9 Audio amplifier: SOUND_SOS A/Speaker

Audio amplifier is sourced power P15V from P board. If the amplifier work abnormally (may due
to short-circuit or overload), the SOUND_SOS signal will go high level and be detected by
IC8001 LED blinks 9 times.

Remove wires connect Yes Remove wires connect to Yes


to L speaker. R speaker.
A board
Power on. Does LED Power on. Does LED
blinks? blinks?

No No

L speaker L+R
speakers

A
A02
IC8000
IC4900
1 Peaks
P15V SOUND_SOS
FROM P BOARD
3 AUDIO AMP
5

9
1.Trouble Shooting SOS protection circuit (7) 10 time LED blink

LED blinks Detail error Board may defect

10 No voltage PNL12V detected A/Panel

PNL12V is regulated by IC5300 from P15V. If the voltage PNL12V is not detected by IC8000, the
LED indicator will blink 10 times. This voltage is only available when IC5300 is activated by
PANEL_VCC_ON command sent from IC8000.

Power on. Check if Remove the cable


No No
voltage PNL12V at pin connect to TC01A. Check Panel
1-4 of TC01A connector if short circuit at pin 1-4 of Module
before LED blinks? TC01A connector?

Yes
Yes
(12V)

A board A board

Panel TC01 TC01A


A
Module 1 1
PNL12V
TCON 2 PNL12V 2
3 3
FRCDCDC
4 4 IC9302

FRC1.0V IC9301
A02 FRC1.8V IC9300
1 PNL12V SOS_SENSE
P15V IC8000
FROM P BOARD
3 IC5300
Peaks
5 PANEL_VCC_ON

10
1.Trouble Shooting SOS protection circuit (8) Solid RED LED (Keeps Standby mode)

Detail error Board may defect

LED keeps Over voltage protection P/A


standby mode

If one of regulated voltages (P15V, SUB5V, SUB3.3V, SUB1.5V, SUB1.1V, USB5V) get over, the
OVP voltage goes high over voltage protection circuit is activated in IC5000 voltage of
TV_SUB_ON goes low turn the TV into standby mode (LED indicator is off).
In this case, after power on, the screen may display in short time, then going back to standby
mode.
Remove P2 connector.
Connect pin 4 to pin 7 of P2
connector to create pseudo Yes
command TV_SUB_ON. Plug P board
in power. Check if over voltage
P15V at pin 1-2-3 of P2
connector?

No USB5V
IC5440 A
A board SUB5V
IC5420
SUB3.3V
IC5400
P P2 A02 SUB1.1V
Q7402 IC8100 IC5000
1 1 SUB1,5V
T7301 P15V
Q7403 2 3 IC8101 ANALOG
3 5 ASIC
P15V OVP
STB5V
IC7502 4 9
TV_SUB_ON TV_SUB_ON
7 13

11
1.Trouble Shooting SOS protection circuit (9) Other Symptom

1. LED backlight does not light up.

Power on. Check if Yes Power up. Check if any Yes


Panel
voltage 3V of BL_ON at voltage of BL_PWM at
Module
pin 2 of P4 connector? pin 1 of P4 connector?

No No

A board A board

Waveform of BL_PWM sent by A board


in standard picture mode
2. LED backlight brightness is low.
Signal BL_PWM controls brightness of LED backlight is a PWM waveform sent by IC8000 of A board.
This BL_PWM has amplitude 3.3V and frequency 120Hz.
- In standard picture mode, average voltage of BL_PWM is about 2.5V (about 80% ON, 20% OFF).
- In vivid picture mode, BL_PWM reaches max voltage 3.3V (100% ON).
The lower BL_PWM voltage, the darker LED backlight brightness.
If BL_PWM voltage is max in vivid picture mode, but LED backlight brightness is still significant darker than
that of in normal condition Panel Module.

Panel Module
PWM_50
CN2 P4 P P2 A02 A
LEFT SIDE V BL_ON BL_ON
---------------------- Backlight 12 2 11 6
LED power IC8000
BACKLIGHT PWM_50 BL_PWM BL_PWM Peaks
(LED driver)
--------------------- V 14 1 13 10
RIGHT SIDE

12
2. Stand by/Start-up Operation (P/A board)

13
2. Start up operation (1)

P
P Transformer P4 LCD Module
T7301 Q7402
24V 7 Power LCD Panel
PFC Output 8
24V
9
For
T7201
LED
IC7201
2 (Back T-CON
BL_ON Light) board

5 PNL12V
P2 3
2 2 A02 4
BL_ON TC01A 1,2,3,4
DC/DC
IC7301
11

7
6

13
AA
TV_SUB_ON
STB5V 5
5VS 9
Output STB5V
16V
1
1 1 P15V
Output Q7403 2 3
16V 5
3

When the TV is plugged in, the power board outputs 5V for standby voltage.
When the power supply receives the TV_SUB_ON signal, it outputs 2 different voltages:
•P15V to the A board on pins 1, 2, and 3 of connector P2.
•24V to the LED backlight power board on pins 7, 8, and 9 of connector P4.
After A board is ready to display, it outputs Backlight on command to LCD Module.

14
2. Start up operation (2)
< from AC plug in to 1 : P board >

Rectifier

through T7301 P2
(PFC) VCC
VCC 10
TP7401 IC 7502
HO 15 D7407 (STB6V)
D7104, Q7301 5 1,2 5
LO 11
7105 Start Vcc Q7302 5V STB
1 VH Reg
R7306- C7514
40 V DC 3
7308
CE
IC7301

R7420
(2.4 V)

REF 5V Good PC7303


6 3

R7421
4.9-5.1V
Ref R7320

P
15
2. Start up operation (3)
< from AC plug in to 1 : P board >

When the TV is plugged in, the rectifier start to produce DC voltage which
leads through PFC circuit directly to the power switches Q7301, Q, 7302.
Beside this DC voltage is provided also for D7104, D7105 which provide start
voltage to pin 1 of power supply IC 7301. When the voltage on pin 1 rise up to
predefined value IC 7301 starts supplyinng of switching pulses for Q7301,
Q7302. Due to this current starts to lead through winding of T7301 which starts
to generate output voltages. One of these voltages VCC is used for power
supplying of the IC 7301 to its pin 10.
When the power supply starts up, the 6 V voltage is providing by
D7407/C7514. This voltage leads to IC7502, which is 5 volts regulator. This
regulator needs to get starts commands, which is provides by IC 7301 pin 3.
This pin is internaly grounded in normal state and the information is carried to
the secondary side by PC7303. Finally there is around 2.4V on pin 3 of IC7502
for start its operation.Then 5V is provided by pins 1 and 2.
This voltage (STB5V) is provided to A board via connector P2 pin5.
So if the TV is plugged in, STB5V is provided to A board without trigger signal.

16
2. Start up operation (4)
< from 1 to 2 : A board >
10 3
POWER
SWITCH GK K
P4 GK4

P2 A02
2.4V LCD_TV_SUB_ON
7 13

8 15
KEY3

IC8000
IC5000
STB
STB5V 5VS 1.1V PEAKS LD4 A10 K10
5 9
Output 1.1V
STB5V
STB Signal
Processing REMOTE
3.3V
3.3V 9 9

5 5
Analog 10 10
P A ASIC
LED_on
3.3V
LED

OFF Standby
(can receive only Power SW) (can receive Power SW, Remote, Viera Link and so on)
North America Power LED: OFF
Except North America Power LED: OFF Power SW on Power LED: RED

17
2. Start up operation (5)
< from 1 to 2 : A board >

The STB5V from pin5 of connector P2 is applied to the Analog ASIC (IC5000) for
supplying power to the Main CPU/PEAKS LD4 (IC8000) on the A board. The Analog
ASIC (IC5000) converts the STB5V to STB3.3V and STB1.2V. These 2 voltages
energize and prepare the microprocessor (CPU) for program execution. The STB3.3V
from the Analog ASIC (IC5000) is also applied to the remote control receiver and the
power LED on the K board through pins 5 and 10 of connector A10/K10.
When the Power Switch on, the key3 signal is grounded. (#1)
The IC8000 lights on the RED LED and is ready to power on the TV by receiving the
Power switch on, Remote on, Viera Link and so on. This is a standby state.
(#1)Only North America model: Power switch on is no need, automatically this procedure is
operated after the TV is plugged in. But the RED LED does
not light.

When the power on command from the power switch, the remote control receiver
and so on is provided to IC8000 PEAKS LD4, (#2)
IC8000 on the A board first outputs the “TV_SUB_ON” command (2.4V). The
“TV_SUB_ON” command is provided to power board via pin 7 of connector P2.
(#2) Only North America model: This command is automatically outputs for approximately
12 seconds only after the TV is first plugged in.

18
2. Start up operation (6)
< from 2 to 3 : P board > P4
D7401 PA 7401 7
,7402 8
PFC C7422
24V Q7402 9
Rectifier IC7201
FUSE
24V
VCC
T7301 Q7403
PA 7402
VCC D7408 16V 1
VCC 10 ,7409
C7423 2
FUSE
IC7301 16V 3
HO 15 +STB IC 7502
Q7202 D7407 12V 5
Q7301 1,2 5
D7104, VH 5V
LO 11 C7514
7105 Start Vcc Q7302 5V STB
1 Reg
R7306- PC7301
7308 40 V DC 3
4 CE
FB feedback

5 IC7401 P2
CS
(mode change)

REF 5V Good
PC7303
6 3
Q7303

Standby/ON SUB-ON
Switch
L=ON
P PC7302
Q7401
7

19
2. Start up operation (7)
< from 2 to 3 : P board >

When the power board receives the TV_SUB_ON signal from IC8000 via pin 7 of
connector P2, it outputs 2 different voltages:
P15V to the A board on pins 1, 2, and 3 of connector P2.
24V to the LED backlight power board on pins 7, 8, and 9 of connector P4.
This command is carried to the primary side by PC7302. This voltage is leaded to
Q7303, whcih provide reference voltage from pin 6 to pin 5 of IC7301.
Therefore the operation of the IC 7301 changes the switching frequency from
standby state and output voltages rise up.
Beside the on command is connected to the Q7202 which provide power supply
VCC of PFC circuit. The PFC starts to operate then.
Output voltages from transformer T7301 start rising up until the moment when IC
7401 started to operate. This IC measures the 16V line output. The output of this
IC is provided by PC7301 to pin 4 of IC7301. IC7301 adjust the switching
frequency by this feedback signal.
The TV_SUB_ON signal also switches on the Q7402,Q7403 to provide output
voltages (16V and 24V ) to other boards.
The 24V is provided to the LCD Module ( LED Backlight Power Supply ).
The P15V is provided to the A board.

20
2. Start up operation (8)
< 3 : A board (SUB voltage) >

P Transformer
T7301 P2 A02
A
PFC
T7201
IC7201
IC8000
2.4V 2.4V R8853 PEAKS LD4
7 13 LCD_TV_SUB_ON
DC/DC R2014
IC7301

P15V 1
IC5000
16V ANALOG ASIC
1 1 6.5V
Output
Q7403 2 3 5V
3 5 IC5420

DCDCEN
SUB5V
IC8706
P15V

3.3V HDMI3.3V
IC5400 6.5V
24V 1.8V IC8702 SUB1.8V
Output 3.3V
Q7402 SUB3.3V
1.1V IC8100
SUB1.1V
1.5V IC8101
SUB1.5V
24V IC5440
5V USB5V
P4 7, 8, 9

21
2. Start up operation (9)
< 3 : A board (SUB voltage) >

The P15V from the P board via pin1,3 and 5 of connector A02 is applied to
Analog ASIC IC5000 and ICs (Voltage regulators) on the A board to generate the
SUB-Voltages used for signal processing operation.
: SUB1.1V, 1.5V, 1.8V, 3.3V, 5V, HDMI3.3V and USB5V
Each voltage regulators start up by high state of DCDCEN signal which is pull up
to P15V. So P15V is provided to A board, each SUB-voltage regulator ICs start output.

22
2. Start up operation (10)
< 3 : A board (OVP circuit) >

P Transformer
A LCD_TV_SUB_ON

IC5000 R8853
T7301 P2 A02
ANALOG ASIC
PFC
T7201
IC7201

IC8000
ASCI PEAKS LD4
2.4V 2.4V N OVP
DC/DC 7 13 SUBON
R2014 8 OVP
IC7301 N OVP
OVP
7
P15V 1
10 DCDCEN
11
16V
1 1 6.5V
Output
Q7403 5V Over
2 3
Voltage

SUB5V
3 5 IC5420 Protection

6.5V DCDCEN
SUB5V Circuit
IC8706
P15V

3.3V HDMI3.3V
24V IC5400 1.8V IC8702 SUB1.8V
Output
Q7402 3.3V SUB3.3V
1.1V IC8100
SUB1.1V
1.5V IC8101
SUB1.5V
24V IC5440
5V USB5V
P4 7, 8, 9

23
2. Start up operation (11)
< 3 : A board (OVP circuit) >

The Sub voltages are monitored for over-voltage condition. If any of these voltage
increases above a predetermined level, the OVP circuit will be triggered by getting
pin 7 of IC5000 to go high.
When pin 7 goes high, the TV_SUB_ON voltage connected to pin 8 is grounded.
This disables the circuit that outputs the P15V and 24V in the power supply.

If any abnormality occurs with P15, the DCDCEN circuit inside IC5000 is triggered
and pin 11 is grounded.
This in term, disables the output of the SUB-Voltage regulator ICs (IC5400, IC5420,
IC5440, IC8100, and IC8101).

24
2. Start up operation (12)
< 4 and 5 : A board (PNL,FRC voltage) >

P P2 A02
LCD_TV_SUB_ON
A
AC IN BL_ON
BL_SOS
7 13 2.4V IC5000
ANALOG IC8000
ASIC PEAKS LD4
DC/DC
IC7301 11 6 3.2V
PEAKS_RST2
10 4

P15V LCD
16V Module
Output 1 1 IC5420 (T-CON
SUB5V
Q7403 2 3 5V board)

3 5

PANEL_VCC_ON2 IC9351 PNL3.3V IC9100


3.3V FRC
P15V IC9300
24V Q7402 FRCDCDCEN 2.5V FRC2.5V
Detect
Output IC9301 IC9303 TC01A
3.2V 1.0V FRC1.025V
24V 1
IC9302
P4 7, 8, 9 2 3 2
1.8V FRC1.8V
6 3
2
LCD Module 12V 4 PNL12V 4
(Power board IC5300
for Back Light)

25
2. Start up operation (12)
< 4 and 5 : A board (PNL,FRC voltage) >

The P15V is also used to generate the PNL-Voltage and FRC-Voltage on A


board. IC5000 outputs the Panel VCC On2 signal. IC5300 starts generating
the PNL12V by this signal. The PNL12V is provided to ICs (Voltage regulator)
for FRC-Voltages and T-con circuit of the LCD Module.

After that, IC8000 outputs the BL_ON command to the LCD Module through P
board. The BL_ON command turns on the LED backlight power supply of the
LCD Module. If the backlight power circuit does not work normally, the
BL_SOS signal is informed to the IC8000. At that time, IC8000 stops
outputting the TV_SUB_ON signal and blinks the red LED 1 times.

26
2.2 Power Supply and LED state of Each State
OFF Standby --- ON (Screen Displays)
(AC A B C D
plug in)

LED: OFF LED: RED


North
America
LCD Module LCD Module
LCD LCD
24V Power 24V Power
24V Panel 24V Panel
Output For Output For
LED T-CON LED T-CON
P4 board P4 board

P P PNL12V
Except P A02 A02 TC01A
P2 P2
P2 A02
North STB5V
5VS
STB5V
5VS
STB5V Output STB5V Output STB5V
America Output 5VS STB5V
P15V A A
16V 16V
Output
16V Output
16V P15V
A

LED: OFF LED: RED LED: GREEN

North America: AC plug in B C (only 12sec) B (Standby)


B (Standby) Power SW on / Remote on / and so on C D (ON)
Except North America: AC plug in A (OFF)
A (OFF) Power SW on B (Standby)
A (OFF) Power SW on B C D (ON)
B (Standby) Power SW on / Remote on / and so on C D (ON)

27
3.Video signal processing

28
3.Video Signal Process(1)
ET5 series Digital Analog
OPT_out Audio_out
D3006 /Headphone
WiFi (USB)
JK8600 IC8458 (USB HUB) A
USB1/2 (Depend on
JK8451/50 the region)
USB 3
FR
(Only
(Only TX- TX- model
model
Antenna TU6706
TU6706 isis separated
separated
terminal
TUNER
TUNER into
into 22 boards)
boards)
Monitor IC8000
IC8000
out (Peaks
(Peaks LD4)
LD4)
JK3005
PC
Resize
Resize IC9100
IC9100
AV IP
IP conv.
conv. FRC
FRC LVDS Data
OSD (Double
(Double Speed)
Speed)
Compo OSD
nent1,2 2D->3D
2D->3D
JK3001

HDMI1/2
JK4701A/00A

JK4702A/03A IC4700
IC4700
HDMI3/4
HDMI_SW
HDMI_SW
JK8600A IC8600
IC8600
LAN
CN8660
(LAN)
(LAN)
SD card

29
3.Video Signal Process(2) Difference between the models for each regions

ET5 series

AV input USB input Monitor out Analog Audio Head Phone Signal Process
output output Board
TC-L**ET5 1 2 (no IC8458) 0 0 0 A
TC-L**ET5X 1 2 (no IC8458) 0 0 0 A
TC-L**ET5W 2 2 (no IC8458) 0 1 0 A
TC-L**ET5A/B 2 3 0 1 1 A
TH-L**ET5* 2 3 0 1 1 A
TX-L**ET5* 2 3 1 0 1 A ( with CI slot )
(1 is SCART) + FR

30
3.Video Signal Process(3) Difference from last year model
2011 model E30
HDMI SD CARD EHERNET USB

Digital TV (IFD) TS IN IC8000 HDMI I/F SW IC


(PEAKS LDA3)
Tuner IC3001 Y/C Separation SD CARD I/F
(AV SW) Resize ETHER I/F
Analog TV I/P Conversion USB I/F
(CVBS) Analog Data Signal Processing
䞉Y/Pb/Pr OSD
Composite 䞉RGB LVDS
AV I/O LVDS DATA
Input
(CVBS) 䞉CVBS Panel
OUT
Component
Terminal
(Y/Pb/Pr)/(RGB) LVDS (T-CON)
DATA

2012 model ET5/ET50 New CPU


PEAKS LD4
HDMI SD CARD EHERNET USB/WiFi
Delete
AV SW IC
Digital TV (IFD)
Digital TV
IC8000 HDMI I/F SW IC
TS IN (PEAKS LD4) IC for
SD CARD I/F
Tuner
Y/C Separation ETHERNET I/F
Passive 3D
Analog TV Resize
USB I/F
I/P Conversion
Signal Processing IC9100
Composite (CVBS) OSD LVDS
2D -> 3D Conversion LVDS DATA
Flame Rate Convert Panel
Component
Input
Terminal
AV I/O OUT Double Speed
LVDS
DATA
(T-CON)
(Y/Pb/Pr)/(RGB) Passive 3D process
AV SW function
is integrated.

31
3.Video Signal Process(4)
The main function of the A board is to select and process one of the incoming video
signals. IC8458 and IC4700 are just switches of USB and HDMI signals. The built in WiFi
module is connected by USB type terminal.
Video input, Component Video Input, HDMI input and the composite video output of the
tuner are all connected to IC8000 for selection. The video input signal can be two formats:
Video, or Y, Pb, Pr. A comb filter inside IC8000 converts the composite video signal of the
main picture to Y and C (luminance and chrominance) signals. The signal is then
converted to RGB. At the completion of this process, the format of the composite signal is
now the same as a digital 1080i component signal. If the incoming video is in the 480p,
720p, 1080i, and 1080p format, the Y, Pb, and Pr signals undergo A/D (analog to digital)
conversion. Finally all picture signals are converted to 1080p.
Digital television reception of the tuner is output in the form of an IF (Intermediate
Frequency) signal. The transport stream from the tuner enters the VSB I/F (Interface)
section of IC8000 where the video signal is extracted and converted to YUV data. The
output is provided to the Video Input I/F for selection. The JPEG data of the SD card enters
the JPEG I/F section of IC8000 for conversion into YUV data and output to the Video Input
I/F circuit. The video input interface outputs the selected picture data to the video process
circuit.
This Video Process section of the IC performs all picture control operations such as
brightness, contrast, color, tint, etc. On Screen Display data such as channel numbers,
Digital TV closed caption, and picture adjustments are mixed with the video data. After the
process, LVDS (Low Voltage Differential Signaling) is output to IC9100. IC9100 converts
the picture data of 50/60Hz to one of 100/120Hz. If in 3D mode, it converts to the right and
left pictures.

32
4. 3D Method

33
4.1 Difference of 3D Methods
Active Method (Except ET5 series) Passive Method (Only ET5 series)
㻿㼥㼚㼏㼔㼞㼛㼚㼕㼦㼑㻌㻿㼕㼓㼚㼍㼘㻌㼀㼞㼍㼚㼟㼙㼕㼠㼠㼑㼞
㻝 㻸 㻻㻰㻰㻌㼘㼕㼚㼑㼟㻌㻦㻌㻼㼛㼘㼍㼞㼕㼦㼕㼚㼓㻌㻲㼕㼘㼙
㻞 㻾 㼒㼛㼞㻌㻸㻱㻲㼀㻌㼑㼥㼑㻌㼜㼕㼏㼠㼡㼞㼑
㻟 㻸
㻠 㻾

㻱㼂㻱㻺㻌㼘㼕㼚㼑㼟㻌㻦㻌㻼㼛㼘㼍㼞㼕㼦㼕㼚㼓㻌㻲㼕㼘㼙
㼒㼛㼞㻌㻾㻵㻳㻴㼀㻌㼑㼥㼑㻌㼜㼕㼏㼠㼡㼞㼑

㻿㼥㼚㼏㼔㼞㼛㼚㼕㼦㼑㻌㻿㼕㼓㼚㼍㼘㻌 㻝㻜㻣㻥 㻸
㻝㻜㻤㻜 㻾
㼎㼥㻌㻵㻾㻌㻌㻌㻌㻌㻌㻌㻌㻌㻔㻙㻞㻜㻝㻝㻕
㼎㼥㻌㻮㼘㼡㼑㼠㼛㼛㼠㼔㻌㻔㻞㻜㻝㻞㻙㻕

㻯㼍㼡㼠㼕㼛㼚㻌㻦㻌
㻺㼛㻌㼏㼔㼍㼚㼓㼑㼍㼎㼕㼘㼕㼠㼥

㻲㼛㼞㻌㻾㻵㻳㻴㼀㻌㼑㼥㼑
㻲㼛㼞㻌㻸㻱㻲㼀㻌㼑㼥㼑 㻲㼛㼞㻌㻸㻱㻲㼀㻌㼑㼥㼑 㻲㼛㼞㻌㻾㻵㻳㻴㼀㻌㼑㼥㼑

No need the
Synchronize Signal
㼏㼘㼛㼟㼑 㼛㼜㼑㼚

㻼㼛㼘㼍㼞㼕㼦㼍㼠㼕㼛㼚㻌㻲㼕㼘㼠㼑㼞 㻼㼛㼘㼍㼞㼕㼦㼍㼠㼕㼛㼚㻌㻲㼕㼘㼠㼑㼞
㼒㼛㼞㻌㻸㻱㻲㼀㻌㼑㼥㼑㻌㼜㼕㼏㼠㼡㼞㼑 㼒㼛㼞㻌㻾㻵㻳㻴㼀㻌㼑㼥㼑㻌㼜㼕㼏㼠㼡㼞㼑
㼛㼜㼑㼚 㼏㼘㼛㼟㼑

L/R LCD shutters on 3D-Eyewear open Each L/R polarizing filters on 3D-Eyewear pass
in synchronization to the L/R pictures. the only L/R pictures.
L/R pictures are displayed at the same time.
L/R pictures are displayed one by one. Each pictures are located line by line on the screen.
(each 60 pictures /s) There are polarizing films on the surface of the LCD Panel.
The polarize direction (rotation) is different by the lines. 34
4.2 Relation of 3D TV to Eyewear

3D-Eyewear Previous 2012


Eyewear Eyewear
3D-TV
Active
Method
Previous 3D model By IR > (Continue to sell)

PDP: VT,GT,ST,UT,XT
By Bluetooth
2012 LCD: WT,DT,ET50 Unavailable
Passive
3D model
By Polarization
Method
LCD: ET5 only Filter
㻺㼛㻌㼏㼔㼍㼚㼓㼑㼍㼎㼕㼘㼕㼠㼥
㼑㼍㼏㼔㻌㼛㼠㼔㼑㼞

35
Update History
Issue date Update part Update explanation
Mar.9th.2012 First version.

36

Vous aimerez peut-être aussi