Académique Documents
Professionnel Documents
Culture Documents
Issue 01
Date 2016-02-29
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Contents
2 Overview......................................................................................................................................... 4
2.1 Introduction.................................................................................................................................................................... 4
2.2 Benefits........................................................................................................................................................................... 4
2.3 Architecture...................................................................................................................................................................4
4 SRB Reset...................................................................................................................................... 20
4.1 SRB Reset Detection.................................................................................................................................................... 20
4.1.1 Detection Principle.................................................................................................................................................... 20
4.1.2 Switches for Call Reestablishment Triggered by an SRB Reset............................................................................... 20
4.2 Call Reestablishment.................................................................................................................................................... 23
4.2.1 Triggering.................................................................................................................................................................. 23
4.2.2 Implementation.......................................................................................................................................................... 24
5 TRB Reset...................................................................................................................................... 25
5.1 TRB Reset Detection.................................................................................................................................................... 25
5.1.1 Detection Principle.................................................................................................................................................... 25
5.1.2 Switches for Call Reestablishment Triggered by a TRB Reset................................................................................. 25
5.2 Call Reestablishment.................................................................................................................................................... 26
5.2.1 Triggering.................................................................................................................................................................. 26
5.2.2 Implementation.......................................................................................................................................................... 26
8 Related Features...........................................................................................................................51
9 Network Impact........................................................................................................................... 52
10 Engineering Guidelines........................................................................................................... 54
10.1 When to Use Call Reestablishment............................................................................................................................ 54
10.2 Required Information................................................................................................................................................. 54
10.3 Planning...................................................................................................................................................................... 56
10.4 Deployment................................................................................................................................................................ 56
10.4.1 Requirements........................................................................................................................................................... 56
10.4.2 Data Preparation...................................................................................................................................................... 56
10.4.3 Activation................................................................................................................................................................ 63
10.4.4 Activation Observation............................................................................................................................................68
10.4.5 Deactivation.............................................................................................................................................................68
10.5 Performance Monitoring.............................................................................................................................................75
10.6 Parameter Optimization.............................................................................................................................................. 77
10.7 Troubleshooting.......................................................................................................................................................... 77
11 Parameters................................................................................................................................... 78
12 Counters.................................................................................................................................... 382
13 Glossary..................................................................................................................................... 407
14 Reference Documents............................................................................................................. 408
1.1 Scope
This document describes the WRFD-140103 Call Reestablishment, including its technical
principles, related features, network impact, and engineering guidelines.
NE Type NE Model
Micro BTS3911E
l Feature change
Changes in features of a specific product version
l Editorial change
Changes in wording or addition of information that was not described in the earlier
version
RAN18.1 01 (2016-02-29)
This issue does not include any changes.
WRFD-14 Call Y Y Y Y Y
0103 Reestablis
hment
NOTE
Y indicates that a feature is supported; N indicates that a feature is not supported; NA indicates that an NE is
not involved, that is, a feature does not require the support of the NE.
The features described in this document are implemented in the same way on macro, micro,
and LampSite base stations.
2 Overview
2.1 Introduction
Call reestablishment is a function by which radio links (RLs) are reestablished when a service
interruption or an access failure occurs in temporary coverage holes and in tunnels, elevators,
and buildings that cause significant signal quality fluctuation.
2.2 Benefits
Call reestablishment initiated by the RAN improves user experience.
2.3 Architecture
Causes That Can Trigger Call Reestablishment
The causes that can trigger call reestablishment after a service interruption or an access failure
are as follows:
l RL out-of-synchronization problem
l SRB reset
l PS TRB reset
l Air interface process timeout
l Air interface process overlap
l Soft handover
l Physical channel reconfiguration
– Physical channel reconfiguration during hard handovers
– Physical channel reconfiguration for the starting of the compressed mode
– Physical channel reconfiguration during code tree reshuffling
– Physical channel reconfiguration during serving cell updates
– Physical channel reconfiguration for inter RNC-UE timer relationship adjustment
when a UE reports event 6G or 6F
– Physical channel reconfiguration during power adjustments for HSUPA channels
l Inter-RAT handover
l RB setup
l RB release
l RB reconfiguration
DCCC RB reconfiguration consists of the following procedures:
– Hybrid automatic repeat request (HARQ) power offset (PO) reconfiguration
– Dynamic channel configuration control (DCCC) triggered by HSPA retry
– DCCC triggered by TTI switching
– DCCC triggered by HSPA+ feature removal after the RAB is released
– DCCC triggered by fallback from DC-HSUPA to SC-HSUPA
– DCCC triggered by channel fallback
– DCCC triggered by event 4A or 4B
– DCCC triggered by coverage-based channel switching from E-DCH to DCH
– Best effort (BE) service downspeeding triggered by load reshuffling
– DCCC triggered by feature fallback
l Measurement control command issuing
l PS data transmission
l Security mode setup
Before releasing RLs due to any of the causes, the RAN detects the service interruption or
access failure and initiates call reestablishment.
Table 2-1 Mapping between service types, triggering processes, and triggering causes
Service Triggering RL out- SRB PS TRB Air Air
Type Process of- reset reset interfac interfac
synchro e e
nizatio process process
n timeout overlap
proble
m
Physical Hard √ √ √ √
channel handove
reconfig r
uration
Compres √ √ √
sed
mode
setup
Serving √ √ √ √
cell
update
Inter-RAT handover √ √ √
RB setup √ √ √ √
RB reconfiguration √ √ √ √
Measurement √ √ √
control command
issuing
PS Physical channel √ √ √ √
reconfiguration
during power
adjustments for
HSUPA channels
PS data transmission √
RB release √ √ √ √
NOTE
The cause "RL out-of-synchronization problem" can trigger call reestablishment in processes not listed
in Table 2-1.
The other causes can trigger call reestablishment only in processes listed in Table 2-1.
After you select UE_DCH_CU_RL_REEST_SWITCH under the
OptimizationSwitch7(BSC6900,BSC6910) parameter, the RNC performs call reestablishment after
receiving a CELL UPDATE message from a UE with the cause value Radio Link Failure or RLC
Unrecoverable Error as a response to one of the following messages delivered by the RNC:
l Radio Bearer Setup message
l Radio Bearer Release message of PS services
l Radio Bearer Reconfiguration message
l Physical Channel Reconfiguration message
l Security Mode Command message
After Call Reestablishment is enabled, call reestablishment triggered by the CELL UPDATE message
from the UE is also supported.
When DCH_CU_CHGCELL_OPT_SWITCH under the OptimizationSwitch8(BSC6900,BSC6910)
parameter is set to 1, if the RNC receives a CELL UPDATE message (with a cause value of Radio Link
Failure or RLC Unrecoverable Error) from a UE in another cell while waiting for the UE's response to
the CELL UPDATE CONFIRM message (not carrying radio bearer), the RNC re-sends a CELL
UPDATE CONFIRM message to initiate call reestablishment.
You are also advised to select the PSREL_DUETO_CSFAIL_OPTIMIZE_SWITCH check box under
the OptimizationSwitch(BSC6900,BSC6910) parameter to ensure the call drop rate benefits provided by
turning on the UE_DCH_CU_RL_REEST_SWITCH.
l Service switches
Service switches include a CS service switch and a PS service switch. Enable a service
switch before enabling a process or cause switch.
l Process switches
All triggering processes listed in Table 2-1 except PS data transmission have a switch.
l Cause switches
All causes except "Air interface process timeout" have a switch.
Call reestablishment can be triggered only when required switches are enabled.
For details about service/process/cause switches of call reestablishment, see descriptions in
the follow-up chapters.
A UE can only reestablish a service on the DCH instead of the FACH if related parameters for
the UE are set as follows:
l The TAC_FUNC(BSC6900,BSC6910) parameter is set to Special_User_Enhance.
l SPECUSER_REEST_TO_FACH_LIMITATION under the
SpecUserFunctionSwitch4(BSC6900,BSC6910) parameter is set to on.
NOTE
l If the number of "in-sync" indications received by the NodeB reaches the value of the
NINSYNCIND(BSC6900,BSC6910) parameter before the
TRlFailure(BSC6900,BSC6910) timer expires, the NodeB stops and resets the
TRlFailure(BSC6900,BSC6910) timer.
l If the number of "in-sync" indications received by the NodeB does not reach the value of
the NINSYNCIND(BSC6900,BSC6910) parameter before the
TRlFailure(BSC6900,BSC6910) timer expires, the NodeB considers that an RL out-of-
synchronization problem has occurred and identifies the RL set where the problem is
located. (An RL set contains all the RLs of a UE under a NodeB.)
NOTE
When a UE's uplink RL sets are all out of synchronization, the events that occur depend on
the situation:
l When the call reestablishment function is not enabled, the call drops or the UE access
finally fails.
l When the call reestablishment function is enabled, the RNC activates a synchronization
timer. If the NodeB does not detect uplink RL synchronization before the timer expires,
call reestablishment is initiated.
Table 3-1 shows the mapping between services,
OptimizationSwitch(BSC6900,BSC6910):RL_RESTORE_SWITCH switch status, and
synchronization timers.
On T313(BSC6900,BSC6910)
NOTE
NOTE
PROCESSSWITCH4(B
SC6900,BSC6910)
parameter.
– For CS services,
CS_RB_SETUP_RL
_REEST_SWITCH
under the
OptimizationSwitch
7(BSC6900,BSC6910
) parameter is also
used.
– For PS services,
PS_RB_SETUP_RL
_REEST_SWITCH
under the
OptimizationSwitch
7(BSC6900,BSC6910
) parameter is also
used.
l Call reestablishment
during RB release is
controlled by
RB_REL_RL_REEST_
SWITCH under the
PROCESSSWITCH4(B
SC6900,BSC6910)
parameter. This switch
applies to CS+PS
combined services.
l Call reestablishment
during RB
reconfiguration in the
DCCC procedure is
controlled by
RB_RECFG_RL_REE
ST_SWITCH under the
OptimizationSwitch(BS
C6900,BSC6910)
parameter.
l Call reestablishment
during RB
reconfiguration in
procedures other than
DCCC is controlled by
NON_DCCC_RBRECF
G_RL_REEST_SWIT
CH under the
ImprovementSwitch(BS
C6900,BSC6910)
parameter.
l Call reestablishment
during security mode
setup is controlled by the
SMC_RL_REEST_SW
ITCH under the
ImprovementSwitch(BS
C6900,BSC6910)
parameter.
NOTE
l The switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
3.2.1 Triggering
Call reestablishment triggered by an uplink RL out-of-synchronization problem can be
performed under the same RNC or under different RNCs over the Iur interface.
3.2.2 Implementation
Figure 3-3 shows how call establishment is implemented.
NOTE
The higher the value of the N313 parameter, the harder it will be for the UE to detect an RL out-
of-synchronization problem and the longer the UE may stay on the verge of RL out-of-
synchronization problem.
2. If the number of "in-sync" indications received consecutively from Layer 1 does not
reach the value of the N315 parameter before the T313 timer expires, the UE transmits
the Cell Update message with the cause value "Radio Link Failure" to the RNC for call
reestablishment. Meanwhile, the UE starts the T302 timer as well as the T314 timer for
CS services or the T315 timer for PS services.
3. If the UE does not receive the Cell Update Confirm message from the RAN side after the
T302 timer expires, the UE retransmits the Cell Update message until the T314/T315
timer expires: (The number of retransmissions is determined by the value of the T302
parameter.)
l If faulty RLs are restored before T314(BSC6900,BSC6910)/T315(BSC6900,BSC6910)
expires, the call reestablishment is successful. Interrupted services are restored or UE
access succeeds.
l If faulty RLs are not restored before T314(BSC6900,BSC6910)/
T315(BSC6900,BSC6910) expires, the call reestablishment fails. Services are released
or UE access fails.
NOTE
Set the T313, N313, N315, and T314 parameters so that UEs can quickly detect RL out-of-
synchronization problem.
Set the timer for RAB assignment on the CN side during call reestablishment to a value greater than the
RB setup response timer (RbSetupRspTmr(BSC6900,BSC6910)) plus the timer
CSRLReEstCellUpdateTmr(BSC6900,BSC6910) (for CS services) or
PSRLReEstCellUpdateTmr(BSC6900,BSC6910) (for PS services).
Set the security mode response timer on the CN side to a value greater than the security mode timer
RRCSECRTMODECMPTMR(BSC6900,BSC6910) plus the timer T314 on the RNC side. Set the timer
for a response to the Relocation Command message that is sent by the CN during inter-RAT handovers
to a value greater than the call reestablishment timer.
l For CS services, set the timer to a value greater than
CSRLReEstCellUpdateTmr(BSC6900,BSC6910).
l For PS services, set the timer to a value greater than
PSRLReEstCellUpdateTmr(BSC6900,BSC6910).
When RBSETUP_RLREEST_RABSETUPCNT_CORRECT and
RBSETUP_UEDCHCU_RABSETUPCNT_CORRECT under the
OptimizationSwitch7(BSC6900,BSC6910) parameter are selected and the RNC receives a message
from the CN during call reestablishment triggered by an RB setup exception of a UE in the CELL_DCH
state, the RNC measures counters related to RAB assignment attempts.
l The network side receives the RADIO LINK FAILURE INDICATION message from the
NodeB.
l Synchronization times out.
After a UE who has only one radio link receives a RADIO LINK FAILURE
INDICATION message, it waits for recovery of the radio link's synchronization. The
timer used in this case is specified by the D2PRlRstrTmr(BSC6900,BSC6910)
parameter in the RNC MML command SET USTATETIMER.
After a UE who has multiple radio links receives a RADIO LINK FAILURE
INDICATION message, it waits for recovery of the radio links' synchronization. The
timer used in this case is specified by the value of the
RlRstrTmr(BSC6900,BSC6910)parameter in the RNC MML command SET
USTATETIMER.
l The best cell is under the SRNC and there is no CS signaling.
The UE transits to the common channel. Then, according to the traffic volume, it transits to a
dedicated channel to finish the call reestablishment. If an SRB resets during the D2P state
transition, the call reestablishment is performed in the same way as that performed during an
SRB reset.
If there is data in the RLC buffer after the D2P state transition is successful, you can run the
RNC MML command SET URRCTRLSWITCH with
D2P_L2DEACT_FAIL_OPT_SWITCH under OptimizationSwitch4(BSC6900,BSC6910)
set to 0 and run the RNC MML command SET URRCTRLSWITCH with
F2P_DATATRANS_OPTIMIZE_SWITCH under
PROCESSSWITCH4(BSC6900,BSC6910) set to 1 to send paging messages to the UE again.
CELL_DCH-to-CELL_PCH reconfiguration and reestablishment is not triggered for the
following blacklisted UEs:
l UEs for which FD_TAC_FORCE_D2F_SWITCH is set to 1
l UEs for which PCH_DISABLED_SWITCH is set to 1
l UEs for which SPECUSER_EFACH_DISABLED_SWITCH is set to 1
l UEs for which SPECUSER_ERACH_DISABLED_SWITCH is set to 1
l UEs for which EFACH_ERACH_UE_D2P_DISABLED_SWITCH under
SpecUserFunctionSwitch3(BSC6900,BSC6910) is set to 1
4 SRB Reset
l If the call reestablishment function is not enabled, the RNC sends the Iu Release Request
message to the core network.
l If the call reestablishment function is enabled, call reestablishment is triggered.
NOTE
l The switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
l If call reestablishment triggered by inter-RAT handover is enabled, you must select
PS_RL_SETUP_SWITCH under OptimizationSwitch(BSC6900,BSC6910) and
DL_TRB_RESET_BUFF_SWITCH under PROCESSSWITCH4(BSC6900,BSC6910).
Otherwise, the inter-RAT handover success rate may decrease.
After you enable the process switch, change the length of the process timer so that call
reestablishment is more likely to be triggered by an SRB reset. The following table lists the
mapping between processes and timers.
RB reconfiguration RbRecfgRspTmr(BSC6900,BSC6910)
RB setup RbSetupRspTmr(BSC6900,BSC6910)
4.2.1 Triggering
Figure 4-1 shows the signaling procedure for call reestablishment triggered by an SRB reset.
4.2.2 Implementation
Except that the trigger cause is different, the process of call reestablishment triggered by an
SRB reset is the same as that triggered by an RL out-of-synchronization problem. For details,
see 3.2.2 Implementation.
5 TRB Reset
NOTE
Call reestablishment triggered by a TRB reset applies only to a single PS service of a UE in the
CELL_DCH state.
5.2.1 Triggering
Figure 5-1 shows the signaling procedure for call reestablishment triggered by a TRB reset.
5.2.2 Implementation
Except that the trigger cause is different, the process of call reestablishment triggered by a
TRB reset is the same as that triggered by an RL out-of-synchronization problem. For details,
see section 3.2.2 Implementation.
Scenario 1
The RNC sends the Radio Bearer Setup message to a UE but does not receive an ACK
message before the RbSetupRspTmr(BSC6900,BSC6910) timer expires. The radio Bearer
Setup fails and either of the following occurs:
l If the call reestablishment function is not enabled, the RAN requests the UE to release
the Iu interface resources and the call drops.
l If the call reestablishment function is enabled, the RNC does not request the UE to
release the Iu interface resources but initiates call reestablishment.
In this scenario, the call reestablishment function is controlled by the service switch and
process switch, as described in Table 6-1.
Table 6-1 Switches for call reestablishment triggered by radio bearer setup timeout in
scenario 1
Service Switch Process Switch Cause
Switch
NOTE
l The service switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
Figure 6-1 shows the signaling procedure for call reestablishment triggered by radio bearer
setup timeout in scenario 1.
Figure 6-1 Call reestablishment triggered by radio bearer setup timeout in scenario 1
Scenario 2
The RNC sends the Radio Bearer Setup message to a UE and receives an ACK message.
However, the RNC does not receive the Radio Bearer Setup Complete message from the UE
before the RbSetupRspTmr(BSC6900,BSC6910) timer expires. Then either of the following
occurs:
l If the call reestablishment function is not enabled, the RNC sends the Iu Release Request
message to the core network and the call drops.
l If the call reestablishment function is enabled, the RNC does not send the Iu Release
Request message to the core network but initiates call reestablishment.
In this scenario, the call reestablishment function is controlled by the service switch and
process switch, as described in Table 6-2.
Table 6-2 Switches for call reestablishment triggered by radio bearer setup timeout in
scenario 2
Service Switch Process Switch Cause
Switch
NOTE
l The service switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
In this scenario, the call reestablishment function is controlled by the service switch and
process switch, as described in Figure 6-2.
Figure 6-2 Call reestablishment triggered by radio bearer setup timeout in scenario 2
l Scenario 1: The RNC sends the Radio Bearer Release message to a UE but does not
receive an ACK message.
l Scenario 2: The RNC sends the Radio Bearer Release message to a UE and receives an
ACK message. However, the RNC does not receive the Radio Bearer Release Complete
message from the UE.
NOTE
All the radio bearer releases mentioned in this section are releases of PS services
Scenario 1
The RNC sends the Radio Bearer Release message to a UE but does not receive an ACK
message before the RbRelRspTmr(BSC6900,BSC6910) timer expires. Then either of the
following occurs:
l If the call reestablishment function is not enabled, the RNC sends the Iu Release Request
message to the core network and the call drops.
l If the call reestablishment function is enabled, the RNC does not send the Iu Release
Request message to the core network and call reestablishment is triggered.
To enable the call reestablishment function triggered by radio bearer release timeout, enable
the service and process switches listed in Table 6-3.
Table 6-3 Switches for call reestablishment triggered by radio bearer release timeout in
scenario 1
NOTE
l The call reestablishment function triggered by radio bearer release timeout applies only to CS+PS
combined services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished only for
CS service.
Figure 6-3 shows the signaling procedure for call reestablishment triggered by radio bearer
release timeout in scenario 1.
Figure 6-3 Call reestablishment triggered by radio bearer release timeout in scenario 1
Scenario 2
The RNC sends the Radio Bearer Release message to a UE and receives an ACK message.
However, the RNC does not receive the Radio Bearer Release Complete message from the
UE before the RbRelRspTmr(BSC6900,BSC6910) timer expires. Then either of the following
occurs:
l If the call reestablishment function is not enabled, the RNC sends the Iu Release Request
message to the core network and the call drops.
l If the call reestablishment function is enabled, the RNC does not send the Iu Release
Request message to the core network and call reestablishment is triggered.
To enable the call reestablishment function in this scenario, enable the service and process
switches listed in Table 6-4.
Table 6-4 Switches for call reestablishment triggered by radio bearer release timeout in
scenario 2
Service Switch Process Switch Cause Switch
NOTE
l The call reestablishment function triggered by radio bearer release timeout applies only to CS+PS
combined services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
Figure 6-4 shows the signaling procedure for call reestablishment triggered by radio bearer
release timeout in scenario 2.
Figure 6-4 Call reestablishment triggered by radio bearer release timeout in scenario 2
l If the call reestablishment function is not enabled, the RNC sends an Iu Release Request
message to the core network and the call drops.
l If the call reestablishment function is enabled, the RNC does not send an Iu Release
Request message to the core network but initiates call reestablishment.
To enable the call reestablishment function in this scenario, enable the service and
process switches listed in Table 6-5.
Table 6-5 Switches for call reestablishment triggered by radio bearer reconfiguration
timeout
NOTE
When call reestablishment is triggered for CS+PS combined services, calls are reestablished for
both CS and PS services.
Figure 6-5 shows the signaling procedure for call reestablishment triggered by radio
bearer reconfiguration timeout.
Table 6-6 Switches for call reestablishment triggered by physical channel reconfiguration
timeout
Service Switch Process Switch Cause
Switch
NOTE
When call reestablishment is triggered for CS+PS combined services, both CS and PS services are
reestablished.
Figure 6-6 shows the signaling procedure for call reestablishment triggered by physical
channel reconfiguration timeout.
To enable the call reestablishment function in this scenario, enable the service and
process switches listed in Table 6-7.
Table 6-7 Switches for call reestablishment triggered by security mode setup timeout
Service Switch Process Switch Cause
Switch
NOTE
Call reestablishment triggered by security mode setup timeout applies to scenarios where a UE has
set up a single service or combined services but the UE experiences a security mode setup failure
when attempting to set up another service.
Figure 6-7 shows the signaling procedure for call reestablishment triggered by security
mode setup timeout.
Table 7-1 Switches for call reestablishment triggered by air-interface process overlap in
scenario 1 (ACK of the Radio Bearer Setup message is not received.)
Service Switch Process Switch Cause Switch
NOTE
l The service switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
l When RB_RL_REEST_OPT_ENH_SWITCH under the
OptimizationSwitch8(BSC6900,BSC6910) parameter is set to 1, the RNC regards an RB setup
during the call reestablishment as successful when the following conditions are met:
- The UE sends a CELL UPDATE or UPLINK SIGNALLING TRANSFER INDICATION message
to the RNC during the RB setup procedure in the CELL_DCH state.
- The message contains the Reconfiguration Status Indicator IE with the value "True."
Table 7-2 Switches for call reestablishment triggered by air-interface process overlap in
scenario 2 (ACK of the Radio Bearer Setup message is received.)
Service Switch Process Switch Cause Switch
NOTE
l The service switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
Table 7-3 Switches for call reestablishment triggered by air-interface process overlap in
scenario 1 (ACK of the Radio Bearer Release message is not received.)
Service Switch Process Switch Cause Switch
NOTE
l The service switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
Table 7-4 Switches for call reestablishment triggered by air-interface process overlap in
scenario 2 (ACK of the Radio Bearer Release message is received.)
Service Switch Process Switch Cause Switch
NOTE
l The service switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
Table 7-5 Switches for call reestablishment triggered by air-interface process overlap in
scenario 1 (ACK of the Radio Bearer Reconfiguration message for a single PS service is not
received.)
Table 7-6 lists the switches for call reestablishment triggered when the RNC does not receive
the ACK of the Radio Bearer Reconfiguration message for CS+PS combined services.
Table 7-6 Switches for call reestablishment triggered by air-interface process overlap in
scenario 1 (ACK of the Radio Bearer Reconfiguration message for CS+PS combined services
is not received.)
NOTE
l The service switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
l When RB_RL_REEST_OPT_ENH_SWITCH under the
OptimizationSwitch8(BSC6900,BSC6910) parameter is set to 1, the RNC regards an RB
reconfiguration during the call reestablishment as successful when the following conditions are met:
- The UE sends a CELL UPDATE or UPLINK SIGNALLING TRANSFER INDICATION message
to the RNC during the RB setup procedure in the CELL_DCH state.
- The message contains the Reconfiguration Status Indicator IE with the value "True."
Table 7-7 Switches for call reestablishment triggered when the UE does not send a Physical
Channel Reconfiguration Complete message to the RNC for a single PS service
Service Switch Process Switch Cause Switch
Table 7-8 lists the switches for call reestablishment triggered when the UE does not send the
RNC a Physical Channel Reconfiguration Complete message for CS+PS combined services.
Table 7-8 Switches for call reestablishment triggered when the UE does not send a Physical
Channel Reconfiguration Complete message to the RNC for CS+PS combined services
Service Switch Process Switch Cause Switch
NOTE
l The switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
l If UE_DCH_CU_RL_REEST_SWITCH under the OptimizationSwitch7(BSC6900,BSC6910)
parameter is set to 1, the RNC initiates call reestablishment when it sends DCCC configurations
through a PHYSICAL CHANNEL RECONFIGURATION message without receiving the
PHYSICAL CHANNEL RECONFIGURATION COMPLETE message from the UE.
Table 7-9 Switches for call reestablishment triggered when the UE does not send the RNC a
Security Mode Complete message
Service Service Switch Process Switch Cause Switch
NOTE
l The service switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
Table 7-10 lists the switches for call reestablishment triggered when the UE does not send the
RNC a Security Mode Complete message. These switches apply to scenarios where the UE
has set up a CS service and attempts to set up a new service.
Table 7-10 Switches for call reestablishment triggered when the UE does not send the RNC a
Security Mode Complete message
Service Service Switch Process Switch Cause Switch
NOTE
l The service switch for CS+PS combined services is the same as that for CS services.
l When call reestablishment is triggered for CS+PS combined services, calls are reestablished for both
CS and PS services.
sends an SRNS CONTEXT RESPONSE message to the CN. Then, the RNC waits for
the IU RELEASE COMMAND message from the CN. The subsequent process is as
follows:
– If SRNS_PROCEDURE_OPTIMIZE_SWITCH under
OptimizationSwitch6(BSC6900,BSC6910) in the MML command SET
URRCTRLSWITCH is set to 1 and the RNC has not received the IU RELEASE
COMMAND message after the timer expires, the RNC sends an IU RELEASE
REQUEST message to the CN with the cause value "Normal Release" and performs
a normal release.
– If SRNS_PROCEDURE_OPTIMIZE_SWITCH under
OptimizationSwitch6(BSC6900,BSC6910) in the MML command SET
URRCTRLSWITCH is set to 0 and the RNC has not received the IU RELEASE
COMMAND message after the timer expires, the RNC sends an IU RELEASE
REQUEST message to the CN with the cause value "TRELOCoverall expiry" and
performs an abnormal release.
l If CALL_RE_ESTAB_CROSS_WITH_SYSOUT_SWITCH under
OptimizationSwitch6(BSC6900,BSC6910) in the MML command SET
URRCTRLSWITCH is set to 0, the RNC ignores the SRNS CONTEXT REQUEST
message and continues to wait for the cell update message from the UE and finish the
call reestablishment process.
8 Related Features
Prerequisite Features
None
Impacted Features
None
9 Network Impact
System Capacity
No impact.
Network Performance
When the call reestablishment function is enabled in scenarios with weak coverage or
significant signal fluctuation, calls will be reestablished for UEs with service interruptions or
access failures that are caused by link failures or control/user plane faults. As a result, the call
drop rate decreases and the UE access success rate increases. The exact gains depend on the
coverage of the live network.
When a UE service is interrupted or the UE access fails, channel element (CE), code
resources, and power resources are released for the UE. After call reestablishment succeeds,
the released resources are re-occupied by the UE.
The call reestablishment function affects end user experience. This function generally affects
CS user experience with more occurrences of mute voice and garbled noise, which can be
observed by the following counters:
l VS.AMRNB.ULGarbledVoice.OccurNum(BSC6900,BSC6910)
l VS.AMRWB.ULGarbledVoice.OccurNum(BSC6900,BSC6910)
l VS.AMRNB.DLGarbledVoice.OccurNum(BSC6900,BSC6910)
l VS.AMRWB.DLGarbledVoice.OccurNum(BSC6900,BSC6910)
The call reestablishment function slightly affects non-real-time PS user experience.
When the call reestablishment function is enabled for the inter-RAT handover, the values of
the KPIs IRATHO.AttOutCS(BSC6900,BSC6910) and
IRATHO.AttOutPSUTRAN(BSC6900,BSC6910) will increase and the handover success
rate also increases because inter-RAT handovers are initiated again after call reestablishment
is complete.
After the D2P reconfiguration and reestablishment algorithm is enabled, D2P state transition
attempts and successful D2P state transitions increase. Meanwhile, call drops or second RRC
connection setup attempts during CELL_DCH-to-CELL_PCH state transitions increase. That
is, the values of the following counters increase:
After the D2F reconfiguration and reestablishment function is enabled:
l The D2F/H2F state transition attempts and successful D2F/H2F state transitions
increase, whereas the D2F/H2F success rate decreases.
D2F state transition success rate = VS.DCCC.Succ.D2F(BSC6900,BSC6910)/
VS.DCCC.D2C.Att(BSC6900,BSC6910) x 100%
H2F state transition success rate = VS.HSDPA.H2F.Succ(BSC6900,BSC6910)/
VS.HSDPA.H2F.Att(BSC6900,BSC6910) x 100%
l The PS call drop rate decreases.
PS Call Drop Ratio with PCH (Cell) = [(VS.RAB.AbnormRel.PS(BSC6900,BSC6910)
- VS.RAB.AbnormRel.PS.PCH(BSC6900,BSC6910) -
VS.RAB.AbnormRel.PS.D2P(BSC6900,BSC6910) -
VS.RAB.AbnormRel.PS.F2P(BSC6900,BSC6910) ) /
(VS.RAB.AbnormRel.PS(BSC6900,BSC6910) +
VS.RAB.NormRel.PS(BSC6900,BSC6910) -
VS.RAB.AbnormRel.PS.PCH(BSC6900,BSC6910) -
VS.RAB.NormRel.PS.PCH(BSC6900,BSC6910) +
VS.DCCC.D2P.Succ(BSC6900,BSC6910) +
VS.DCCC.Succ.F2P(BSC6900,BSC6910) )]*100%
10 Engineering Guidelines
NOTE
To enable call reestablishment due to different trigger causes, processes, or service types, different
switches need to be turned on. When the calculation result of the formula for CS or PS services is
greater than 30%, it is recommended that all corresponding switches for CS or PS services be
turned on.
l Whether switches for performance measurement of failed call reestablishment attempts
during RB setup procedures have been turned on
Check whether RAB_SETUP_CNT_CORRECT_SWITCH under
ImprovementSwitch(BSC6900,BSC6910) and
RAB_SETUP_ATT_R99_CNT_CORRECT_SWITCH under
OptimizationSwitch7(BSC6900,BSC6910) have been set to ON. If they are not set to
ON, it is recommended that the following commands be executed to set them to ON:
SET URRCTRLSWITCH: ImprovementSwitch=RAB_SETUP_CNT_CORRECT_SWITCH-1;
SET URRCTRLSWITCH: OptimizationSwitch7=RAB_SETUP_ATT_R99_CNT_CORRECT_SWITCH-1;
After the preceding switches are set to ON, the RNC counts call reestablishment
attempts that fail in the following scenarios:
– Scenario 1: In the RAB setup process, the RNC delivers a RADIO BEARER
SETUP message to the UE but does not receive an ACK message from the UE. It
initiates a call reestablishment process but the process fails.
– Scenario 2: In the RAB setup process, the RNC delivers a RADIO BEARER
SETUP message to the UE but does not receive an ACK message from the UE.
Instead, it receives a cell update request with the cause value "radio link failure" or
"RLC Unrecoverable error" and the cell update process fails.
– Scenario 3: In the RAB setup process, the RNC delivers a RADIO BEARER
SETUP message to the UE and receives a cell update request with a cause value
"cell reselection." However, the call update process fails.
l Value of the RAB assignment request response timer on the CN side
Value of the RAB assignment request response timer on the CN side, which must be
greater than the value of RbSetupRspTmr(BSC6900,BSC6910) plus the timer
CSRLReEstCellUpdateTmr(BSC6900,BSC6910) (for CS services) or
PSRLReEstCellUpdateTmr(BSC6900,BSC6910) (for PS services).
If the timer on the CN side does not meet the preceding requirement, the gain in RB
reestablishment during the RAB setup process decreases.
l Whether RBSETUP_RLREEST_RABSETUPCNT_CORRECT and
RBSETUP_UEDCHCU_RABSETUPCNT_CORRECT under the
OptimizationSwitch7(BSC6900,BSC6910) parameter are selected. It is recommended
that these options be selected.
If the switches are turned on, the RNC increments the number of RRC connection setup
attempts by one when the following condition is met:
The RNC receives an IU REL COMMAND message from the CN during RB
reestablishment of a UE in the CELL_DCH state.
l Whether RLREEST_RAB_SETUPFAIL_CNT_FIX_SWITCH under
OptimizationSwitch8(BSC6900,BSC6910) has been set to ON. If the switch has been set
to ON, the RNC measures RAB setup failures based on the causes of call
reestablishment when a call reestablishment attempt fails during the RAB setup and the
UE's connection is released. If the switch has been set to OFF, the RNC measures RAB
setup failures based on the causes of call reestablishment failures.
10.3 Planning
None
10.4 Deployment
10.4.1 Requirements
None
Timer T302(BS Set this parameter based on Radio network NE: RNC
302 C6900,BS network conditions. plan (internal) MO:
C6910) Otherwise, network UCONNMO
performance will be greatly DETIMER
affected. The recommended
value is 2s. Batch
modification
Constant N302(BS Set this parameter based on Radio network on the CME is
302 C6900,BS network conditions. plan (internal) supported.
C6910) Otherwise, network
performance will be greatly
affected. The recommended
value is 3.
Num of Noutsync Set this parameter based on Radio network NE: RNC
Continuo Ind(BSC network conditions. plan (internal) MO: UCELL
us Out of 6900,BSC Otherwise, network
Sync Ind 6910) performance will be greatly Batch
affected. The lower the value modification
of this parameter, the earlier on the CME is
call reestablishment is supported.
triggered by an RL out-of-
synchronization problem.
The recommended value is
50, but you can set this
parameter to a value even
lower than the recommended
value to improve user
experience.
Timer for CSRLRe Timer for call Radio network NE: RNC
Wait for EstCellU reestablishment for CS plan (internal) MO:
Cell pdateTm services. USTATETIM
Update r(BSC690 Set this parameter based on ER
Specific 0,BSC691 network conditions.
to CS UE 0) Batch
Otherwise, network modification
performance will be greatly on the CME is
affected. The recommended supported.
value is 15000.
10.4.3 Activation
l Run the SET USTATETIMER command to set Timer for Wait for Cell Update
Specific to CS UE and Timer for Wait for Cell Update Specific to PS UE.
l Run the SET USTATETIMER command to set HO active set update response timer,
HO PhyCh reconfiguration timer, and Wait RB reconfiguration response timer.
Step 2 Enable the switches that control the call reestablishment function for CS and PS services.
Step 3 Enable the switches that control the call reestablishment function triggered by RL out-of-
synchronization problems and SRB resets.
Step 4 Enable the switch that controls the call reestablishment function triggered by soft handovers.
Step 5 Enable the switch that controls the call reestablishment function triggered by measurement
control.
Step 6 Enable the switch that controls the call reestablishment function triggered by TRB resets.
Step 7 Enable the switch that controls the call reestablishment function triggered by physical channel
reconfiguration.
Step 8 Enable the switch that controls the call reestablishment function triggered by RB setup.
.
1. Run the SET URRCTRLSWITCH command. In this step, select
RB_SETUP_RL_REEST_SWITCH and
RB_SETUP_ENHANCE_RL_REEST_SWITCH under Process Control Switch 4.
2. Run the SET URRCTRLSWITCH command. In this step, select
CS_RB_SETUP_RL_REEST_SWITCH and
PS_RB_SETUP_RL_REEST_SWITCH under the Optimization Switch 7 parameter.
NOTE
The RAB assignment timer needs to be configured on the CN side and its value must be greater than the
value of RbSetupRspTmr(BSC6900,BSC6910) plus the timer
CSRLReEstCellUpdateTmr(BSC6900,BSC6910) (for CS services) or
PSRLReEstCellUpdateTmr(BSC6900,BSC6910) (for PS services).
Step 9 Enable the switch that controls the call reestablishment function triggered by RB
reconfiguration during DCCC.
NOTE
l In the call reestablishment triggered by inter-RAT handover, the RAB assignment timer configured
on the CN must be greater than 15s.
l If call reestablishment triggered by inter-RAT handover is enabled for CS services, you must select
the PS_RL_SETUP_SWITCH check box under the OptimizationSwitch(BSC6900,BSC6910)
parameter. Otherwise, the inter-RAT handover success rate for CS services may decrease.
Step 13 Enable the enhanced switch that controls whether call reestablishment can be triggered by
physical channel reconfiguration timeout.
Run the SET URRCTRLSWITCH command. In this step, select
PHYCHRECFG_ENH_RL_REEST_SWITCH under Process Control Switch 4.
Step 14 Enable the enhanced switch that controls whether call reestablishment can be triggered by
radio bearer reconfiguration timeout during the DCCC procedure.
Run the SET URRCTRLSWITCH command. In this step, select
RBRECFG_ENH_RL_REEST_SWITCH under Process Control Switch 4.
Step 15 Enable the enhanced switch that controls whether call reestablishment can be triggered by
radio bearer reconfiguration timeout in procedures other than DCCC.
Run the SET URRCTRLSWITCH command. In this step, select
NON_DCCC_RBRECFG_RL_REEST_SWITCH under Improvement Switch.
Step 16 Enable the switch that controls whether call reestablishment can be triggered by security
mode setup timeout.
Run the SET URRCTRLSWITCH command. In this step, select
SMC_RL_REEST_SWITCH under Improvement Switch.
NOTE
Set the security mode response timer on the CN side to a value greater than the security mode timer
RRCSECRTMODECMPTMR(BSC6900,BSC6910) plus the timer T314(BSC6900,BSC6910) on the
RNC side.
----End
ImprovementSwitch=NON_DCCC_RBRECFG_RL_REEST_SWITCH-1;
//Setting the switch for call reestablishment after RB release to on
SET URRCTRLSWITCH: PROCESSSWITCH4=RB_REL_RL_REEST_SWITCH-1;
//(Optional) Turning on the switch that controls the optimization of overlapped
PS RB release process and CU process for UEs in the Cell_DCH state
SET URRCTRLSWITCH: OptimizationSwitch8=DCH_RB_REL_CU_OVERLAP_OPT_SWITCH-1;
//Setting the switch for call reestablishment in security mode to on
SET URRCTRLSWITCH: ImprovementSwitch=SMC_RL_REEST_SWITCH-1;
//Setting the switch for call reestablishment after cancellation of an inter-RAT
handover to on
SET URRCTRLSWITCH:
PROCESSSWITCH4=IRATHO_HOCANCEL_RL_REEST_SWITCH-1&DL_TRB_RESET_BUFF_SWITCH-1;
//(Optional) Enabling the CELL_DCH-to-CELL_PCH reconfiguration and
reestablishment algorithm
SET URRCTRLSWITCH: PROCESSSWITCH5=D2P_RECFG_REEST_SWITCH-1;
SET USTATETIMER: D2PRlRstrTmr=100;
SET URRCTRLSWITCH: OptimizationSwitch4=D2P_L2DEACT_FAIL_OPT_SWITCH-0;
SET URRCTRLSWITCH: PROCESSSWITCH4= F2P_DATATRANS_OPTIMIZE_SWITCH-1;
//Enabling the enhanced call reestablishment function for overlapping soft
handover procedures
SET URRCTRLSWITCH:OptimizationSwitch8=ASU_CU_CROSS_OPT_ENH_SWITCH-1;
//(Optional) Enabling D2F reconfiguration and reestablishment
SET URRCTRLSWITCH: OptimizationSwitch7=RLFAIL_OR_TRBRST_D2F_RLREEST_SWITCH-1;
SET URRCTRLSWITCH: OptimizationSwitch7=FACH_OUTOFSER_OPT_SWITCH-1;
Set parameters listed in the table in "Data Preparation" section from top to bottom on the
CME. For instructions on how to perform the CME single configuration, see CME Single
Configuration Operation Guide.
Step 2 (Optional) Modify objects in batches on the CME. (CME batch modification center)
To modify objects in batches, click on the CME to start the batch modification wizard.
For instructions on how to perform a batch modification through the CME batch modification
center, press F1 while running the wizard to obtain online help.
To check whether a parameter supports batch modification, see the Remarks column in the
table in "Data Preparation" section.
NOTE
When configuring the feature on the CME, perform a single configuration first, and then perform a batch
modification if required.
Configure the parameters of a single object before a batch modification. Perform a batch modification
before logging out of the parameter setting interface.
----End
10.4.5 Deactivation
The following table describes the parameters for deactivating this feature.
Timer 302 T302(BSC6900, Set to the values they were before the NE: RNC
BSC6910) function was enabled. MO:
UCONNMOD
Constant N302(BSC6900,
ETIMER
302 BSC6910)
Batch
Timer 313 T313(BSC6900, modification
BSC6910) on the CME is
supported.
Constant N313(BSC6900,
313 BSC6910)
Constant N315(BSC6900,
315 BSC6910)
Num of NoutsyncInd(B Set to the values they were before the NE: RNC
Continuous SC6900,BSC69 function was enabled. MO: UCELL
Out of Sync 10)
Ind Batch
modification
Num of NInsyncInd(BS on the CME is
Continuous C6900,BSC691 supported.
in Sync Ind 0)
Timer for CSRLReEstCell Set to the values they were before the NE: RNC
Wait for UpdateTmr(BS function was enabled. MO:
Cell Update C6900,BSC691 USTATETIM
Specific to 0) ER
CS UE
Batch
modification
on the CME is
supported.
Timer for PSRLReEstCell Set to the values they were before the
Wait for UpdateTmr(BS function was enabled.
Cell Update C6900,BSC691
Specific to 0)
PS UE
Step 2 Disable the switches that control the call reestablishment function triggered by RL out-of-
synchronization problems and SRB resets.
Step 3 Disable the switches that control the call reestablishment function triggered by soft handovers.
Step 4 Disable the switch that control the call reestablishment function triggered by measurement
control.
Step 5 Disable the switch that control the call reestablishment function triggered by TRB resets.
Run the SET URRCTRLSWITCH command and clear
TRB_RESET_RL_REEST_SWITCH under Process Control Switch 4.
Step 6 Disable the switch that controls the call reestablishment function triggered by physical
channel reconfiguration.
Run the SET URRCTRLSWITCH command and clear PHY_RECFG_REEST_SWITCH
under Process Control Switch 4.
Step 7 Disable the switch that controls the call reestablishment function triggered by RB setup.
Run the SET URRCTRLSWITCH command and clear
RB_SETUP_RL_REEST_SWITCH and
RB_SETUP_ENHANCE_RL_REEST_SWITCH under Process Control Switch 4.
Step 8 Disable the switch that controls the call reestablishment function triggered by RB
reconfiguration.
Run the SET URRCTRLSWITCH command and clear
RB_RECFG_RL_REEST_SWITCH(RB_RECFG_RL_REEST_SWITCH) under
Optimization Switch.
Step 9 Disable the switch that controls the call reestablishment function triggered by RB release.
Run the SET URRCTRLSWITCH command and clear RB_REL_RL_REEST_SWITCH
under Process Control Switch 4 and clear
DCH_RB_REL_CU_OVERLAP_OPT_SWITCH under Optimization Switch 8.
Step 10 Disable the switch that controls the call reestablishment function under different RNCs.
Run the SET URRCTRLSWITCH command and clear IUR_RL_REEST_SWITCH under
Process Control Switch 4.
Step 11 Disable the switch that controls the call reestablishment function triggered by inter-RAT
handover.
Run the SET URRCTRLSWITCH command and clear
IRATHO_HOCANCEL_RL_REEST_SWITCH under Process Control Switch 4.
Step 12 Disable the enhanced switch that controls whether call reestablishment can be triggered by
physical channel reconfiguration timeout.
Run the SET URRCTRLSWITCH command and clear
PHYCHRECFG_ENH_RL_REEST_SWITCH under Process Control Switch 4.
Step 13 Disable the enhanced switch that controls whether call reestablishment can be triggered by
radio bearer reconfiguration timeout during the DCCC procedure.
Run the SET URRCTRLSWITCH command and clear
RBRECFG_ENH_RL_REEST_SWITCH under Process Control Switch 4.
Step 14 Disable the enhanced switch that controls whether call reestablishment can be triggered by
radio bearer reconfiguration timeout during procedures other than DCCC.
Run the SET URRCTRLSWITCH command and clear
NON_DCCC_RBRECFG_RL_REEST_SWITCH under Improvement Switch.
Step 15 Disable the switch that controls whether call reestablishment can be triggered by security
mode setup timeout.
----End
NOTE
When you deactivate the call reestablishment function, change the values of the following parameters
back to their settings before this function was activated: T302(BSC6900,BSC6910),
N302(BSC6900,BSC6910), T313(BSC6900,BSC6910), N313(BSC6900,BSC6910),
N315(BSC6900,BSC6910), T314(BSC6900,BSC6910)(CS), T315(BSC6900,BSC6910)(PS),
NInsyncInd(BSC6900,BSC6910), NoutsyncInd(BSC6900,BSC6910),
TRlFailure(BSC6900,BSC6910), RbRecfgRspTmr(BSC6900,BSC6910),
HoAsuTmr(BSC6900,BSC6910) and HoPhychRecfgTmr(BSC6900,BSC6910). Otherwise, network
performance will be greatly affected.
You can query the values of the following counters to learn the effect of the call
reestablishment function on CS services:
l VS.AttRlReEst.CS(BSC6900,BSC6910): provides the number of call reestablishment
attempts for CS services in a cell.
l VS.SuccRlReEst.CS(BSC6900,BSC6910): provides the number of successful call
reestablishments for CS services in a cell.
PS Services
After the call reestablishment function is enabled for PS services, observe the following KPIs:
l Call drop rate: [VS.RAB.AbnormRel.PS(BSC6900,BSC6910)/
(VS.RAB.AbnormRel.PS(BSC6900,BSC6910) +
VS.RAB.NormRel.PS(BSC6900,BSC6910))] x 100%
l RAB setup success rate:
[(VS.RAB.SuccEstabPS.Conv(BSC6900,BSC6910)+VS.RAB.SuccEstabPS.Str(BSC
6900,BSC6910) +VS.RAB.SuccEstabPS.Int(BSC6900,BSC6910)
+VS.RAB.SuccEstabPS.Bkg(BSC6900,BSC6910))/
(VS.RAB.AttEstabPS.Conv(BSC6900,BSC6910)+VS.RAB.AttEstabPS.Str(BSC690
0,BSC6910)+VS.RAB.AttEstabPS.Int(BSC6900,BSC6910)
+VS.RAB.AttEstabPS.Bkg(BSC6900,BSC6910))]x100%
l Inter-RAT handover success rate for PS services:
(IRATHO.SuccOutPSUTRAN(BSC6900,BSC6910))/
(IRATHO.AttOutPSUTRAN(BSC6900,BSC6910)-
VS.IRATHOPS.Cancel.ReEstab(BSC6900,BSC6910)) 100%
l Values of the following counters, which measure the number of PS RABs abnormally
released due to RF reasons, will decrease:
– VS.RAB.AbnormRel.PS.RF(BSC6900,BSC6910)
– VS.RAB.AbnormRel.PS.RF.ULSync(BSC6900,BSC6910)
– VS.RAB.AbnormRel.PS.RF.SRBReset(BSC6900,BSC6910)
– VS.RAB.AbnormRel.PS.RF.TRBReset(BSC6900,BSC6910)
l Values of the following counters, which measure the number of PS RAB establishment
failures due to RF reasons, will decrease:
– VS.RAB.FailEstabPS.RNL(BSC6900,BSC6910)
– VS.RAB.FailEstabPS.IubFail(BSC6900,BSC6910)
– VS.RAB.FailEstabPS.UuFail(BSC6900,BSC6910)
– VS.RAB.FailEstabPS.SRBReset(BSC6900,BSC6910)
– VS.RAB.FailEstabPS.CellUpd(BSC6900,BSC6910)
– VS.RAB.FailEstabPS.UuNoReply(BSC6900,BSC6910)
After the call reestablishment function is enabled, the preceding KPIs should be improved or
the same as those before the function was enabled. If the KPIs deteriorated, optimize them.
After the call reestablishment function is enabled, the values of the
IRATHO.AttOutCS(BSC6900,BSC6910) and
IRATHO.AttOutPSUTRAN(BSC6900,BSC6910) counters should increase.
You can query the values of the following counters to learn the effect of the call
reestablishment function on PS services:
10.7 Troubleshooting
None
11 Parameters
Ultra- 3)DCCC_HHO_CU_NO_CHANGING_GTPU_IP_S
Flash WITCH(Keep GTPU IP switch for DCCC/HHO/CU)
CSFB Whether the RNC is forbidden to modify the GTP-U
Camp & local IP address at the transport layer during the
Handov DCCC, hard handover, or cell update procedure
er Based initiated by the RNC.
on SPI
1: Indicates that this switch is set to ON. The RNC is
forbidden to modify the GTP-U local IP address at the
transport layer in the preceding scenario.
0: Indicates that this switch is set to OFF. The RNC
can modify the GTP-U local IP address at the
transport layer in the preceding scenario.
4)RAB_MODIFY_NO_CHANGING_GTPU_IP_SW
ITCH(Keep GTPU IP switch for RAB modification)
Whether the RNC is forbidden to modify the GTP-U
local IP address at the transport layer during the RAB
modification procedure initiated by the PS CN.
1: Indicates that this switch is set to ON. The RNC is
forbidden to modify the GTP-U local IP address at the
transport layer in the preceding scenario. If the
transport layer information sent by the CN during the
RAB modification procedure differs from the current
information, the RNC is forbidden to change the GTP-
U local IP address at the transport layer during the
transmission information modification procedure. If
the transmission information modification procedure
fails and
RAB_MOD_IUPS_ADMIFAIL_GTPU_REEST_SWI
TCH under the "OptimizationSwitch5" parameter in
the "SET URRCTRLSWITCH" command is set to
ON, the RNC reestablishes the GTP-U, and this
switch does not take effect.
0: Indicates that this switch is set to OFF. The RNC
can modify the GTP-U local IP address at the
transport layer in the preceding scenario.
5)IUR_F2P_P2P_OVERLAP_CU_TRIG_DSCR_SW
ITCH(DSCR switch for Iur Cell Update)
Whether the SRNC directly initiates the Directed
Signaling Connection Re-establishment (DSCR)
procedure when a cross-Iur F2P or P2P procedure
overlaps a cross-Iur cell update procedure and the
SRNC is processing the cell update message.
1: Indicates that this switch is set to ON. The SRNC
directly initiates the DSCR procedure instead of the
relocation procedure in the preceding scenario.
16)CSFB_USER_IDENTIFY_OPT_SWITCH(CSFB
User Identification Optimization Switch)
Whether to use an optimized method to identify CSFB
UEs.
1: Indicates that this switch is set to ON. The RNC
identifies a UE supporting LTE as a CSFB UE whose
RAU message should be delayed if the RRC
Connection Request message sent by the UE meets
the following conditions:
(1) The "Domain indicator" IE in this message is set to
CS domain.
(2) The "Establishment cause" IE in this message is
set to Originating Conversational Call, Emergency
Call, or Terminating Conversational Call.
(3) This message does not contain the "Pre-redirection
info" IE.
0: Indicates that this switch is set to OFF. The RNC
does not use an optimized method to identify CSFB
UEs.
17)F2D_RBSETUP_CU_OVERLAP_OPT_SWITC
H(Support Overlap of F2D RB Setup and CU Caused
by RL Failures)
Whether the RNC supports the overlap of F2D RB
setup and a cell update procedure triggered by radio
link failures.
1: Indicates that this switch is set to ON. If the RNC
receives a CELL UPDATE or RNSAP UL SIG
TRANSF IND message with the cause value "radio
link failure" while waiting for the UE's response
during F2D RB setup, the RNC supports the overlap
of these two procedures.
0: Indicates that this switch is set to OFF. In this
scenario, the RNC does not support the overlap of
these two procedures.
18)INIT_DT_OVERLAP_CU_OPT_SWITCH(Optim
ize Cell Update During Initial Direct Transfer)
Whether the RNC processes the CELL UPDATE
message received from the UE while waiting for the
UE's initial direct transfer message.
1: Indicates that this switch is set to ON. The RNC
processes the CELL UPDATE message received from
the UE while waiting for the UE's initial direct
transfer message.
0: Indicates that this switch is set to OFF. The RNC
does not process the CELL UPDATE message
MNTN_TWO_PENDING_INTEGRITY_CFG_SWIT
CH,
DCCC_HHO_CU_NO_CHANGING_GTPU_IP_SWI
TCH,
RAB_MODIFY_NO_CHANGING_GTPU_IP_SWIT
CH,
IUR_F2P_P2P_OVERLAP_CU_TRIG_DSCR_SWIT
CH, STATE_TRANS_COUNT_OPT_SWITCH,
CU_RB_CFG_OPT_SWITCH,
SEND_RNSAP_RESET_AGAIN_SWITCH,
SYS_HO_RELOC_CMP_OPT_SWITCH,
CSPS_SYS_HO_IN_SMC_SWITCH,
MOCN_REDIR_GET_SPID_OPT_SWITCH,
DCH_DISCARD_NONDCH_CU_MSG_SWITCH,
CMCF_ACTIVE_RECFG_REEST_SWITCH,
DCH_RB_REL_CU_OVERLAP_OPT_SWITCH,
FACH_SRNS_CONTEXT_REQ_OPT_SWITCH,
CSFB_USER_IDENTIFY_OPT_SWITCH,
F2D_RBSETUP_CU_OVERLAP_OPT_SWITCH,
INIT_DT_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_CIPHER_OPT_SWITCH,
RLREEST_RAB_SETUPFAIL_CNT_FIX_SWITCH,
MOCN_SAME_DOMAIN_DISC_INIT_DT_SWITC
H, RL_PROCEDURE_OPT_SWITCH2,
RABSETUP_OVERLAP_CU_RELOC_OPT_SWITC
H, RL_CNT_OPT_SWITCH,
TRNC_RELOC_IN_SUCC_OPT_SWITCH,
RELOC_WITHOUT_GLOBAL_CN_ID_OPT_SWIT
CH, RELOC_ACK_WAIT_IUUP_INIT_SWITCH,
ASU_CU_CROSS_OPT_ENH_SWITCH,
RB_RL_REEST_OPT_ENH_SWITCH,
DCH_CU_CHGCELL_OPT_SWITCH,
RELOC_SILENT_DETECT_SWITCH,
RL_FAIL_SUSP_SHO_DEL_SWITCH
Unit: None
Actual Value Range:
PS_RAB_REL_GTPU_RESOURCE_UNAVAILABL
E,
MNTN_TWO_PENDING_INTEGRITY_CFG_SWIT
CH,
DCCC_HHO_CU_NO_CHANGING_GTPU_IP_SWI
TCH,
RAB_MODIFY_NO_CHANGING_GTPU_IP_SWIT
CH,
IUR_F2P_P2P_OVERLAP_CU_TRIG_DSCR_SWIT
CH,
STATE_TRANS_COUNT_OPT_SWITCH,
CU_RB_CFG_OPT_SWITCH,
SEND_RNSAP_RESET_AGAIN_SWITCH,
SYS_HO_RELOC_CMP_OPT_SWITCH,
CSPS_SYS_HO_IN_SMC_SWITCH,
MOCN_REDIR_GET_SPID_OPT_SWITCH,
DCH_DISCARD_NONDCH_CU_MSG_SWITCH,
CMCF_ACTIVE_RECFG_REEST_SWITCH,
DCH_RB_REL_CU_OVERLAP_OPT_SWITCH,
FACH_SRNS_CONTEXT_REQ_OPT_SWITCH,
CSFB_USER_IDENTIFY_OPT_SWITCH,
F2D_RBSETUP_CU_OVERLAP_OPT_SWITCH,
INIT_DT_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_CIPHER_OPT_SWITCH,
RLREEST_RAB_SETUPFAIL_CNT_FIX_SWITCH,
MOCN_SAME_DOMAIN_DISC_INIT_DT_SWITC
H,
RL_PROCEDURE_OPT_SWITCH2,
RABSETUP_OVERLAP_CU_RELOC_OPT_SWITC
H,
RL_CNT_OPT_SWITCH,
TRNC_RELOC_IN_SUCC_OPT_SWITCH,
RELOC_WITHOUT_GLOBAL_CN_ID_OPT_SWIT
CH,
RELOC_ACK_WAIT_IUUP_INIT_SWITCH,
ASU_CU_CROSS_OPT_ENH_SWITCH,
RB_RL_REEST_OPT_ENH_SWITCH,
DCH_CU_CHGCELL_OPT_SWITCH,
RELOC_SILENT_DETECT_SWITCH,
RL_FAIL_SUSP_SHO_DEL_SWITCH
Default Value:
PS_RAB_REL_GTPU_RESOURCE_UNAVAILABL
E:
0,MNTN_TWO_PENDING_INTEGRITY_CFG_SW
ITCH:
0,DCCC_HHO_CU_NO_CHANGING_GTPU_IP_S
WITCH:
0,RAB_MODIFY_NO_CHANGING_GTPU_IP_SWI
TCH:
0,IUR_F2P_P2P_OVERLAP_CU_TRIG_DSCR_SW
ITCH:0,STATE_TRANS_COUNT_OPT_SWITCH:
0,CU_RB_CFG_OPT_SWITCH:
31)RELOC_SILENT_DETECT_SWITCH
Whether the one-way audio detection is started at an
earlier time during an SRNS relocation procedure.
1: Indicates that this switch is set to ON. The one-way
audio detection is started after the user-plane
resources of the DRNC are prepared.
0: Indicates that this switch is set to OFF. The one-
way audio detection is started after the SRNS
relocation or inter-RAT handover is complete.
32)RL_FAIL_SUSP_SHO_DEL_SWITCH
Whether the RNC delays deleting radio links (RLs)
during a soft handover when RL restoration times out.
1: Indicates that this switch is set to ON. When some
RLs fall out of synchronization or some new RLs are
initially synchronized and when RL restoration times
out, the RNC delays triggering soft handovers and
deleting unsynchronized RLs. If all the RLs for a UE
in the CELL_DCH state fall out of synchronization
and the RL restoration times out, the RNC delays
triggering abnormal releases or RL reestablishment.
0: Indicates that this switch is set to OFF. When some
RLs fall out of synchronization or some new RLs are
initially synchronized and when RL restoration times
out, the RNC triggers soft handovers and deletes
unsynchronized RLs. If all the RLs for a UE in the
CELL_DCH state fall out of synchronization and RL
restoration times out, the RNC triggers abnormal
release or RL reestablishment.
GUI Value Range:
PS_RAB_REL_GTPU_RESOURCE_UNAVAILABL
E,
MNTN_TWO_PENDING_INTEGRITY_CFG_SWIT
CH,
DCCC_HHO_CU_NO_CHANGING_GTPU_IP_SWI
TCH,
RAB_MODIFY_NO_CHANGING_GTPU_IP_SWIT
CH,
IUR_F2P_P2P_OVERLAP_CU_TRIG_DSCR_SWIT
CH, STATE_TRANS_COUNT_OPT_SWITCH,
CU_RB_CFG_OPT_SWITCH,
SEND_RNSAP_RESET_AGAIN_SWITCH,
SYS_HO_RELOC_CMP_OPT_SWITCH,
CSPS_SYS_HO_IN_SMC_SWITCH,
MOCN_REDIR_GET_SPID_OPT_SWITCH,
DCH_DISCARD_NONDCH_CU_MSG_SWITCH,
CMCF_ACTIVE_RECFG_REEST_SWITCH,
DCH_RB_REL_CU_OVERLAP_OPT_SWITCH,
FACH_SRNS_CONTEXT_REQ_OPT_SWITCH,
CSFB_USER_IDENTIFY_OPT_SWITCH,
F2D_RBSETUP_CU_OVERLAP_OPT_SWITCH,
INIT_DT_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_CIPHER_OPT_SWITCH,
RLREEST_RAB_SETUPFAIL_CNT_FIX_SWITCH,
MOCN_SAME_DOMAIN_DISC_INIT_DT_SWITC
H, RL_PROCEDURE_OPT_SWITCH2,
RABSETUP_OVERLAP_CU_RELOC_OPT_SWITC
H, RL_CNT_OPT_SWITCH,
TRNC_RELOC_IN_SUCC_OPT_SWITCH,
RELOC_WITHOUT_GLOBAL_CN_ID_OPT_SWIT
CH, RELOC_ACK_WAIT_IUUP_INIT_SWITCH,
ASU_CU_CROSS_OPT_ENH_SWITCH,
RB_RL_REEST_OPT_ENH_SWITCH,
DCH_CU_CHGCELL_OPT_SWITCH,
RELOC_SILENT_DETECT_SWITCH,
RL_FAIL_SUSP_SHO_DEL_SWITCH
Unit: None
Actual Value Range:
PS_RAB_REL_GTPU_RESOURCE_UNAVAILABL
E,
MNTN_TWO_PENDING_INTEGRITY_CFG_SWIT
CH,
DCCC_HHO_CU_NO_CHANGING_GTPU_IP_SWI
TCH,
RAB_MODIFY_NO_CHANGING_GTPU_IP_SWIT
CH,
IUR_F2P_P2P_OVERLAP_CU_TRIG_DSCR_SWIT
CH,
STATE_TRANS_COUNT_OPT_SWITCH,
CU_RB_CFG_OPT_SWITCH,
SEND_RNSAP_RESET_AGAIN_SWITCH,
SYS_HO_RELOC_CMP_OPT_SWITCH,
CSPS_SYS_HO_IN_SMC_SWITCH,
MOCN_REDIR_GET_SPID_OPT_SWITCH,
DCH_DISCARD_NONDCH_CU_MSG_SWITCH,
CMCF_ACTIVE_RECFG_REEST_SWITCH,
DCH_RB_REL_CU_OVERLAP_OPT_SWITCH,
FACH_SRNS_CONTEXT_REQ_OPT_SWITCH,
CSFB_USER_IDENTIFY_OPT_SWITCH,
F2D_RBSETUP_CU_OVERLAP_OPT_SWITCH,
INIT_DT_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_CIPHER_OPT_SWITCH,
RLREEST_RAB_SETUPFAIL_CNT_FIX_SWITCH,
MOCN_SAME_DOMAIN_DISC_INIT_DT_SWITC
H,
RL_PROCEDURE_OPT_SWITCH2,
RABSETUP_OVERLAP_CU_RELOC_OPT_SWITC
H,
RL_CNT_OPT_SWITCH,
TRNC_RELOC_IN_SUCC_OPT_SWITCH,
RELOC_WITHOUT_GLOBAL_CN_ID_OPT_SWIT
CH,
RELOC_ACK_WAIT_IUUP_INIT_SWITCH,
ASU_CU_CROSS_OPT_ENH_SWITCH,
RB_RL_REEST_OPT_ENH_SWITCH,
DCH_CU_CHGCELL_OPT_SWITCH,
RELOC_SILENT_DETECT_SWITCH,
RL_FAIL_SUSP_SHO_DEL_SWITCH
Default Value:
PS_RAB_REL_GTPU_RESOURCE_UNAVAILABL
E:
0,MNTN_TWO_PENDING_INTEGRITY_CFG_SW
ITCH:
0,DCCC_HHO_CU_NO_CHANGING_GTPU_IP_S
WITCH:
0,RAB_MODIFY_NO_CHANGING_GTPU_IP_SWI
TCH:
0,IUR_F2P_P2P_OVERLAP_CU_TRIG_DSCR_SW
ITCH:0,STATE_TRANS_COUNT_OPT_SWITCH:
0,CU_RB_CFG_OPT_SWITCH:
0,SEND_RNSAP_RESET_AGAIN_SWITCH:
0,SYS_HO_RELOC_CMP_OPT_SWITCH:
0,CSPS_SYS_HO_IN_SMC_SWITCH:
0,MOCN_REDIR_GET_SPID_OPT_SWITCH:
1,DCH_DISCARD_NONDCH_CU_MSG_SWITCH:
0,CMCF_ACTIVE_RECFG_REEST_SWITCH:
0,DCH_RB_REL_CU_OVERLAP_OPT_SWITCH:
0,FACH_SRNS_CONTEXT_REQ_OPT_SWITCH:
0,CSFB_USER_IDENTIFY_OPT_SWITCH:
0,F2D_RBSETUP_CU_OVERLAP_OPT_SWITCH:
0,INIT_DT_OVERLAP_CU_OPT_SWITCH:
0,SRVCC_RELOC_IN_CIPHER_OPT_SWITCH:
0,RLREEST_RAB_SETUPFAIL_CNT_FIX_SWITC
H:
0,MOCN_SAME_DOMAIN_DISC_INIT_DT_SWIT
CH:
0,RL_PROCEDURE_OPT_SWITCH2:0,RABSETUP
_OVERLAP_CU_RELOC_OPT_SWITCH:
0,RL_CNT_OPT_SWITCH:
0,TRNC_RELOC_IN_SUCC_OPT_SWITCH:
0,RELOC_WITHOUT_GLOBAL_CN_ID_OPT_SWI
TCH:0,RELOC_ACK_WAIT_IUUP_INIT_SWITCH:
0,ASU_CU_CROSS_OPT_ENH_SWITCH:
0,RB_RL_REEST_OPT_ENH_SWITCH:
0,DCH_CU_CHGCELL_OPT_SWITCH:
0,RELOC_SILENT_DETECT_SWITCH:
0,RL_FAIL_SUSP_SHO_DEL_SWITCH:0
4)FACH_OUTOFSER_OPT_SWITCH(Out-of-
Service Optimization Switch for CELL_FACH UEs)
Whether the RNC identifies the CELL_FACH UEs
that are in the out-of-service state.
1: Indicates that this switch is set to ON. The RNC
identifies the CELL_FACH UEs that are in the out-of-
service state.
0: Indicates that this switch is set to OFF. The RNC
does not identify the CELL_FACH UEs that are in the
out-of-service state.
5)P2D_PREPFAIL_OPT_SWITCH(Optimization
Switch for P2D Admission Failures)
Whether the RNC triggers a P2F state transition for
the UE that has experienced an RL setup failure, RL
setup timeout, or an admission failure during a P2D
state transition, U2D state transition, P2D DRD
procedure, or U2D DRD procedure triggered by the
cell update procedure.
1: Indicates that this switch is set to ON. The RNC
switches the UE to the CELL_FACH state after a P2D
state transition failure or P2D DRD failure caused by
the preceding reasons.
0: Indicates that this switch is set to OFF. The RNC
does not switch the UE to the CELL_FACH state
when the P2D state transition or P2D DRD procedure
fails due to the preceding reasons.
6)URA_PCH_RESEL_CU_OPT_SWITCH(Optimize
Cell Update for UEs in the URA_PCH State)
Whether the RNC processes the Cell Update messages
with the cause value "Cell reselection" or "Periodic
cell update" sent by UEs in the URA_PCH state.
1: Indicates that this switch is set to ON. The RNC
initiates reconfiguration procedures to switch UEs to
the CELL_PCH state.
0: Indicates that this switch is set to OFF. The RNC
does not process the Cell Update message in the
preceding scenario, and consequently UE connections
are abnormally released.
7)D2F_ABNORMAL_FORCETOFACH_SWITCH(F
orce UEs to CELL_FACH upon D2F State Transition
Failures)
Whether the RNC commands UEs in the CELL_DCH
state to switch to the CELL_FACH state when these
UEs experience a failure during CELL_DCH-to-
17)PLMNID_OPT_IN_RELOC_RQD_SWITCH(Opt
imize PLMN ID in the Relocation Required MSG)
Whether to optimize the PLMN ID in the Relocation
Required message.
1: Indicates that this switch is set to ON. The PLMN
ID in the Relocation Required message is optimized.
0: Indicates that this switch is set to OFF. The PLMN
ID in the Relocation Required message is not
optimized.
18)RB_PROCEDURE_OPT_SWITCH(RB
Optimization Switch)
Whether the RNC preferentially processes the
optimization in RB procedure.
1: Indicates that this switch is set to ON. The RNC
preferentially processes the following optimization:
(1)The RNC does not deactivate DC-HSDPA for a UE
when sending a NAS RB reconfiguration message to
the UE.
(2)The RNC rolls back the new configuration of RLC
when the RB reconfiguration is failed.
0: Indicates that this switch is set to OFF. The RNC
does not preferentially process the optimization.
19)PLATINUM_TMSI_BROADCAST_OPT_SWITC
H(Optimize the Broadcast of Platinum User TMSIs)
Whether to optimize the broadcast of the temporary
mobile subscriber identities (TMSIs) of platinum
users.
1: Indicates that this switch is set to ON. The master
RNC sends TMSI broadcast messages to the other
RNCs carrying the same logical RNC if the message
delivery to one RNC fails.
0: Indicates that this switch is set to OFF. The master
RNC terminates the delivery of TMSI broadcast
messages if the message delivery to one RNC carrying
the same logical RNC fails.
20)SPECUSER_FAST_RBCFG_OPT_SWITCH
Whether a UE can use the blacklisted Fast Radio
Bearer Setup feature when the UE's IMEI TAC is
unknown.
1: Indicates that this switch is set to ON. When a UE's
IMEI TAC is unknown, the UE cannot use the
blacklisted Fast Radio Bearer Setup feature.
URA_PCH_RESEL_CU_OPT_SWITCH,
D2F_ABNORMAL_FORCETOFACH_SWITCH,
RLFAIL_OR_TRBRST_D2F_RLREEST_SWITCH,
UE_DCH_CU_RL_REEST_SWITCH,
CS_RB_SETUP_RL_REEST_SWITCH,
PS_RB_SETUP_RL_REEST_SWITCH,
RBSETUP_RLREEST_RABSETUPCNT_CORREC
T,
RBSETUP_UEDCHCU_RABSETUPCNT_CORREC
T,
PROC_FOREC_SUCC_COUNTER_OPT_SWITCH,
FD_SCRI_RCV_IN_RRC_PROC_OPT_SWITCH,
INNER_CBC_ENCODE_OPT_SWITCH,
PLMNID_OPT_IN_RELOC_RQD_SWITCH,
RB_PROCEDURE_OPT_SWITCH,
PLATINUM_TMSI_BROADCAST_OPT_SWITCH,
SPECUSER_FAST_RBCFG_OPT_SWITCH,
RB_SETUP_F2D_CU_CROSS_OPT_SWITCH,
RESTORE_DISCARD_RAB_ASSIGN_REQ_SWIT
CH, IUR_SIG_E2D_OPT_SWITCH,
RAB_SETUP_ATT_R99_CNT_CORRECT_SWITC
H,
SRB_OVER_HSDPA_CFN_CORRECT_SWITCH,
CS_RAB_SETUP_DRD_OPT_SWITCH,
SERVICE_QUALITY_MEAS_OPT_SWITCH,
IRATHO_HO_OUT_PROCEDURE_OPT_SWITCH,
IUB_ATM_IP_RL_RECFG_OPT_SWITCH,
ACTIVE_CMCF_FAIL_RL_REEST_SWITCH,
PFM_PS_CELLDCHUES_PLMN_OPTI_SWITCH,
RL_REEST_TRIGGER_MSG_OPT_SWITCH
Unit: None
Actual Value Range:
F2PU_RESELECT_CU_OVERLAP_SWITCH,
F2PU_DATATRANS_CU_OVERLAP_SWITCH,
F2P_USE_AM_RLC_SWITCH,
FACH_OUTOFSER_OPT_SWITCH,
P2D_PREPFAIL_OPT_SWITCH,
URA_PCH_RESEL_CU_OPT_SWITCH,
D2F_ABNORMAL_FORCETOFACH_SWITCH,
RLFAIL_OR_TRBRST_D2F_RLREEST_SWITCH,
UE_DCH_CU_RL_REEST_SWITCH,
CS_RB_SETUP_RL_REEST_SWITCH,
PS_RB_SETUP_RL_REEST_SWITCH,
RBSETUP_RLREEST_RABSETUPCNT_CORREC
T,
RBSETUP_UEDCHCU_RABSETUPCNT_CORREC
T,
PROC_FOREC_SUCC_COUNTER_OPT_SWITCH,
FD_SCRI_RCV_IN_RRC_PROC_OPT_SWITCH,
INNER_CBC_ENCODE_OPT_SWITCH,
PLMNID_OPT_IN_RELOC_RQD_SWITCH,
RB_PROCEDURE_OPT_SWITCH,
PLATINUM_TMSI_BROADCAST_OPT_SWITCH,
SPECUSER_FAST_RBCFG_OPT_SWITCH,
RB_SETUP_F2D_CU_CROSS_OPT_SWITCH,
RESTORE_DISCARD_RAB_ASSIGN_REQ_SWIT
CH,
IUR_SIG_E2D_OPT_SWITCH,
RAB_SETUP_ATT_R99_CNT_CORRECT_SWITC
H,
SRB_OVER_HSDPA_CFN_CORRECT_SWITCH,
CS_RAB_SETUP_DRD_OPT_SWITCH,
SERVICE_QUALITY_MEAS_OPT_SWITCH,
IRATHO_HO_OUT_PROCEDURE_OPT_SWITCH,
IUB_ATM_IP_RL_RECFG_OPT_SWITCH,
ACTIVE_CMCF_FAIL_RL_REEST_SWITCH,
PFM_PS_CELLDCHUES_PLMN_OPTI_SWITCH,
RL_REEST_TRIGGER_MSG_OPT_SWITCH
Default Value:
F2PU_RESELECT_CU_OVERLAP_SWITCH:
0,F2PU_DATATRANS_CU_OVERLAP_SWITCH:
0,F2P_USE_AM_RLC_SWITCH:
0,FACH_OUTOFSER_OPT_SWITCH:
0,P2D_PREPFAIL_OPT_SWITCH:
0,URA_PCH_RESEL_CU_OPT_SWITCH:
0,D2F_ABNORMAL_FORCETOFACH_SWITCH:
0,RLFAIL_OR_TRBRST_D2F_RLREEST_SWITCH
:0,UE_DCH_CU_RL_REEST_SWITCH:
0,CS_RB_SETUP_RL_REEST_SWITCH:
1,PS_RB_SETUP_RL_REEST_SWITCH:
1,RBSETUP_RLREEST_RABSETUPCNT_CORRE
CT:
0,RBSETUP_UEDCHCU_RABSETUPCNT_CORRE
CT:
0,PROC_FOREC_SUCC_COUNTER_OPT_SWITC
H:
0,FD_SCRI_RCV_IN_RRC_PROC_OPT_SWITCH:
0,INNER_CBC_ENCODE_OPT_SWITCH:
0,PLMNID_OPT_IN_RELOC_RQD_SWITCH:
0,RB_PROCEDURE_OPT_SWITCH:
0,PLATINUM_TMSI_BROADCAST_OPT_SWITC
H:0,SPECUSER_FAST_RBCFG_OPT_SWITCH:
0,RB_SETUP_F2D_CU_CROSS_OPT_SWITCH:
0,RESTORE_DISCARD_RAB_ASSIGN_REQ_SWI
TCH:0,IUR_SIG_E2D_OPT_SWITCH:
0,RAB_SETUP_ATT_R99_CNT_CORRECT_SWIT
CH:
0,SRB_OVER_HSDPA_CFN_CORRECT_SWITCH:
0,CS_RAB_SETUP_DRD_OPT_SWITCH:
0,SERVICE_QUALITY_MEAS_OPT_SWITCH:
0,IRATHO_HO_OUT_PROCEDURE_OPT_SWITC
H:0,IUB_ATM_IP_RL_RECFG_OPT_SWITCH:
0,ACTIVE_CMCF_FAIL_RL_REEST_SWITCH:
0,PFM_PS_CELLDCHUES_PLMN_OPTI_SWITCH
:0,RL_REEST_TRIGGER_MSG_OPT_SWITCH:0
4)FACH_OUTOFSER_OPT_SWITCH(Out-of-
Service Optimization Switch for CELL_FACH UEs)
Whether the RNC identifies the CELL_FACH UEs
that are in the out-of-service state.
1: Indicates that this switch is set to ON. The RNC
identifies the CELL_FACH UEs that are in the out-of-
service state.
0: Indicates that this switch is set to OFF. The RNC
does not identify the CELL_FACH UEs that are in the
out-of-service state.
5)P2D_PREPFAIL_OPT_SWITCH(Optimization
Switch for P2D Admission Failures)
Whether the RNC triggers a P2F state transition for
the UE that has experienced an RL setup failure, RL
setup timeout, or an admission failure during a P2D
state transition, U2D state transition, P2D DRD
procedure, or U2D DRD procedure triggered by the
cell update procedure.
1: Indicates that this switch is set to ON. The RNC
switches the UE to the CELL_FACH state after a P2D
state transition failure or P2D DRD failure caused by
the preceding reasons.
0: Indicates that this switch is set to OFF. The RNC
does not switch the UE to the CELL_FACH state
when the P2D state transition or P2D DRD procedure
fails due to the preceding reasons.
6)URA_PCH_RESEL_CU_OPT_SWITCH(Optimize
Cell Update for UEs in the URA_PCH State)
Whether the RNC processes the Cell Update messages
with the cause value "Cell reselection" or "Periodic
cell update" sent by UEs in the URA_PCH state.
1: Indicates that this switch is set to ON. The RNC
initiates reconfiguration procedures to switch UEs to
the CELL_PCH state.
0: Indicates that this switch is set to OFF. The RNC
does not process the Cell Update message in the
preceding scenario, and consequently UE connections
are abnormally released.
7)D2F_ABNORMAL_FORCETOFACH_SWITCH(F
orce UEs to CELL_FACH upon D2F State Transition
Failures)
Whether the RNC commands UEs in the CELL_DCH
state to switch to the CELL_FACH state when these
UEs experience a failure during CELL_DCH-to-
17)PLMNID_OPT_IN_RELOC_RQD_SWITCH(Opt
imize PLMN ID in the Relocation Required MSG)
Whether to optimize the PLMN ID in the Relocation
Required message.
1: Indicates that this switch is set to ON. The PLMN
ID in the Relocation Required message is optimized.
0: Indicates that this switch is set to OFF. The PLMN
ID in the Relocation Required message is not
optimized.
18)RB_PROCEDURE_OPT_SWITCH(RB
Optimization Switch)
Whether the RNC preferentially processes the
optimization in RB procedure.
1: Indicates that this switch is set to ON. The RNC
preferentially processes the following optimization:
(1)The RNC does not deactivate DC-HSDPA for a UE
when sending a NAS RB reconfiguration message to
the UE.
(2)The RNC rolls back the new configuration of RLC
when the RB reconfiguration is failed.
0: Indicates that this switch is set to OFF. The RNC
does not preferentially process the optimization.
19)PLATINUM_TMSI_BROADCAST_OPT_SWITC
H(Optimize the Broadcast of Platinum User TMSIs)
Whether to optimize the broadcast of the temporary
mobile subscriber identities (TMSIs) of platinum
users.
1: Indicates that this switch is set to ON. The master
RNC sends TMSI broadcast messages to the other
RNCs carrying the same logical RNC if the message
delivery to one RNC fails.
0: Indicates that this switch is set to OFF. The master
RNC terminates the delivery of TMSI broadcast
messages if the message delivery to one RNC carrying
the same logical RNC fails.
20)SPECUSER_FAST_RBCFG_OPT_SWITCH
Whether a UE can use the blacklisted Fast Radio
Bearer Setup feature when the UE's IMEI TAC is
unknown.
1: Indicates that this switch is set to ON. When a UE's
IMEI TAC is unknown, the UE cannot use the
blacklisted Fast Radio Bearer Setup feature.
URA_PCH_RESEL_CU_OPT_SWITCH,
D2F_ABNORMAL_FORCETOFACH_SWITCH,
RLFAIL_OR_TRBRST_D2F_RLREEST_SWITCH,
UE_DCH_CU_RL_REEST_SWITCH,
CS_RB_SETUP_RL_REEST_SWITCH,
PS_RB_SETUP_RL_REEST_SWITCH,
RBSETUP_RLREEST_RABSETUPCNT_CORREC
T,
RBSETUP_UEDCHCU_RABSETUPCNT_CORREC
T,
PROC_FOREC_SUCC_COUNTER_OPT_SWITCH,
FD_SCRI_RCV_IN_RRC_PROC_OPT_SWITCH,
INNER_CBC_ENCODE_OPT_SWITCH,
PLMNID_OPT_IN_RELOC_RQD_SWITCH,
RB_PROCEDURE_OPT_SWITCH,
PLATINUM_TMSI_BROADCAST_OPT_SWITCH,
SPECUSER_FAST_RBCFG_OPT_SWITCH,
RB_SETUP_F2D_CU_CROSS_OPT_SWITCH,
RESTORE_DISCARD_RAB_ASSIGN_REQ_SWIT
CH, IUR_SIG_E2D_OPT_SWITCH,
RAB_SETUP_ATT_R99_CNT_CORRECT_SWITC
H,
SRB_OVER_HSDPA_CFN_CORRECT_SWITCH,
CS_RAB_SETUP_DRD_OPT_SWITCH,
SERVICE_QUALITY_MEAS_OPT_SWITCH,
IRATHO_HO_OUT_PROCEDURE_OPT_SWITCH,
IUB_ATM_IP_RL_RECFG_OPT_SWITCH,
ACTIVE_CMCF_FAIL_RL_REEST_SWITCH,
PFM_PS_CELLDCHUES_PLMN_OPTI_SWITCH,
RL_REEST_TRIGGER_MSG_OPT_SWITCH
Unit: None
Actual Value Range:
F2PU_RESELECT_CU_OVERLAP_SWITCH,
F2PU_DATATRANS_CU_OVERLAP_SWITCH,
F2P_USE_AM_RLC_SWITCH,
FACH_OUTOFSER_OPT_SWITCH,
P2D_PREPFAIL_OPT_SWITCH,
URA_PCH_RESEL_CU_OPT_SWITCH,
D2F_ABNORMAL_FORCETOFACH_SWITCH,
RLFAIL_OR_TRBRST_D2F_RLREEST_SWITCH,
UE_DCH_CU_RL_REEST_SWITCH,
CS_RB_SETUP_RL_REEST_SWITCH,
PS_RB_SETUP_RL_REEST_SWITCH,
RBSETUP_RLREEST_RABSETUPCNT_CORREC
T,
RBSETUP_UEDCHCU_RABSETUPCNT_CORREC
T,
PROC_FOREC_SUCC_COUNTER_OPT_SWITCH,
FD_SCRI_RCV_IN_RRC_PROC_OPT_SWITCH,
INNER_CBC_ENCODE_OPT_SWITCH,
PLMNID_OPT_IN_RELOC_RQD_SWITCH,
RB_PROCEDURE_OPT_SWITCH,
PLATINUM_TMSI_BROADCAST_OPT_SWITCH,
SPECUSER_FAST_RBCFG_OPT_SWITCH,
RB_SETUP_F2D_CU_CROSS_OPT_SWITCH,
RESTORE_DISCARD_RAB_ASSIGN_REQ_SWIT
CH,
IUR_SIG_E2D_OPT_SWITCH,
RAB_SETUP_ATT_R99_CNT_CORRECT_SWITC
H,
SRB_OVER_HSDPA_CFN_CORRECT_SWITCH,
CS_RAB_SETUP_DRD_OPT_SWITCH,
SERVICE_QUALITY_MEAS_OPT_SWITCH,
IRATHO_HO_OUT_PROCEDURE_OPT_SWITCH,
IUB_ATM_IP_RL_RECFG_OPT_SWITCH,
ACTIVE_CMCF_FAIL_RL_REEST_SWITCH,
PFM_PS_CELLDCHUES_PLMN_OPTI_SWITCH,
RL_REEST_TRIGGER_MSG_OPT_SWITCH
Default Value:
F2PU_RESELECT_CU_OVERLAP_SWITCH:
0,F2PU_DATATRANS_CU_OVERLAP_SWITCH:
0,F2P_USE_AM_RLC_SWITCH:
0,FACH_OUTOFSER_OPT_SWITCH:
0,P2D_PREPFAIL_OPT_SWITCH:
0,URA_PCH_RESEL_CU_OPT_SWITCH:
0,D2F_ABNORMAL_FORCETOFACH_SWITCH:
0,RLFAIL_OR_TRBRST_D2F_RLREEST_SWITCH
:0,UE_DCH_CU_RL_REEST_SWITCH:
0,CS_RB_SETUP_RL_REEST_SWITCH:
1,PS_RB_SETUP_RL_REEST_SWITCH:
1,RBSETUP_RLREEST_RABSETUPCNT_CORRE
CT:
0,RBSETUP_UEDCHCU_RABSETUPCNT_CORRE
CT:
0,PROC_FOREC_SUCC_COUNTER_OPT_SWITC
H:
0,FD_SCRI_RCV_IN_RRC_PROC_OPT_SWITCH:
0,INNER_CBC_ENCODE_OPT_SWITCH:
0,PLMNID_OPT_IN_RELOC_RQD_SWITCH:
0,RB_PROCEDURE_OPT_SWITCH:
0,PLATINUM_TMSI_BROADCAST_OPT_SWITC
H:0,SPECUSER_FAST_RBCFG_OPT_SWITCH:
0,RB_SETUP_F2D_CU_CROSS_OPT_SWITCH:
0,RESTORE_DISCARD_RAB_ASSIGN_REQ_SWI
TCH:0,IUR_SIG_E2D_OPT_SWITCH:
0,RAB_SETUP_ATT_R99_CNT_CORRECT_SWIT
CH:
0,SRB_OVER_HSDPA_CFN_CORRECT_SWITCH:
0,CS_RAB_SETUP_DRD_OPT_SWITCH:
0,SERVICE_QUALITY_MEAS_OPT_SWITCH:
0,IRATHO_HO_OUT_PROCEDURE_OPT_SWITC
H:0,IUB_ATM_IP_RL_RECFG_OPT_SWITCH:
0,ACTIVE_CMCF_FAIL_RL_REEST_SWITCH:
0,PFM_PS_CELLDCHUES_PLMN_OPTI_SWITCH
:0,RL_REEST_TRIGGER_MSG_OPT_SWITCH:0
VS.HSUPA.HARQ.NACK.TTI10ms
VS.HSUPA.HARQ.LOST.TTI10ms
VS.PS.DLMeanThroughput.TCPTransfer.TotalBytes
VS.PS.DLMeanThroughput.TCPTransfer
0: This switch is turned off. The RNC measures the
preceding counters.
GUI Value Range:
PSREL_DUETO_CSFAIL_OPTIMIZE_SWITCH,
IPC_TIME_OUT_RETRANS_SWITCH,
HSDSCH_DATA_FRAME_TYPE_2_SWITCH,
HSDSCH_CAPACITY_REQ_TIMES_SWITCH,
AM_RLC_SPECIAL_HE_COMPATIBLE_SWITCH,
REMOVE_BAND_NOISE_SILENCE_AND_VQI_S
WITCH, UL_COMBINE_OPTIMIZE_SWITCH,
HSUPA_FASTDELIVER_OPTIMIZE_SWITCH,
SRB_OVER_HSDPA_CFN_OPTIMIZE_SWITCH,
MACD_4B_MEAS_OPTIMIZE_SWITCH,
RACH_PACKET_DISCARD_SWITCH,
MACC_PAGING_STAT_OPTI_SWITCH,
ERRFRAME_DISCARD_SWITCH,
MT_IMPROVE_SWITCH,
UP_MAINT_STAT_COUNT_SWITCH
Unit: None
Actual Value Range:
PSREL_DUETO_CSFAIL_OPTIMIZE_SWITCH,
IPC_TIME_OUT_RETRANS_SWITCH,
HSDSCH_DATA_FRAME_TYPE_2_SWITCH,
HSDSCH_CAPACITY_REQ_TIMES_SWITCH,
AM_RLC_SPECIAL_HE_COMPATIBLE_SWITCH,
REMOVE_BAND_NOISE_SILENCE_AND_VQI_S
WITCH, UL_COMBINE_OPTIMIZE_SWITCH,
HSUPA_FASTDELIVER_OPTIMIZE_SWITCH,
SRB_OVER_HSDPA_CFN_OPTIMIZE_SWITCH,
MACD_4B_MEAS_OPTIMIZE_SWITCH,
RACH_PACKET_DISCARD_SWITCH,
MACC_PAGING_STAT_OPTI_SWITCH,
ERRFRAME_DISCARD_SWITCH,
MT_IMPROVE_SWITCH,
UP_MAINT_STAT_COUNT_SWITCH
Default Value:
PSREL_DUETO_CSFAIL_OPTIMIZE_SWITCH:
0,IPC_TIME_OUT_RETRANS_SWITCH:
1,HSDSCH_DATA_FRAME_TYPE_2_SWITCH:
0,HSDSCH_CAPACITY_REQ_TIMES_SWITCH:
0,AM_RLC_SPECIAL_HE_COMPATIBLE_SWITC
H:
0,REMOVE_BAND_NOISE_SILENCE_AND_VQI_
SWITCH:0,UL_COMBINE_OPTIMIZE_SWITCH:
0,HSUPA_FASTDELIVER_OPTIMIZE_SWITCH:
0,SRB_OVER_HSDPA_CFN_OPTIMIZE_SWITCH:
0,MACD_4B_MEAS_OPTIMIZE_SWITCH:
0,RACH_PACKET_DISCARD_SWITCH:
0,MACC_PAGING_STAT_OPTI_SWITCH:
0,ERRFRAME_DISCARD_SWITCH:
0,MT_IMPROVE_SWITCH:
0,UP_MAINT_STAT_COUNT_SWITCH:0
Unit: None
Actual Value Range:
PSREL_DUETO_CSFAIL_OPTIMIZE_SWITCH,
HSDSCH_CAPACITY_REQ_TIMES_SWITCH,
AM_RLC_SPECIAL_HE_COMPATIBLE_SWITCH,
REMOVE_BAND_NOISE_SILENCE_AND_VQI_S
WITCH, UL_COMBINE_OPTIMIZE_SWITCH,
HSUPA_FASTDELIVER_OPTIMIZE_SWITCH,
SRB_OVER_HSDPA_CFN_OPTIMIZE_SWITCH,
MACD_4B_MEAS_OPTIMIZE_SWITCH,
RACH_PACKET_DISCARD_SWITCH,
MACC_PAGING_STAT_OPTI_SWITCH,
ERRFRAME_DISCARD_SWITCH,
MT_IMPROVE_SWITCH,
UP_MAINT_STAT_COUNT_SWITCH
Default Value:
PSREL_DUETO_CSFAIL_OPTIMIZE_SWITCH:
0,HSDSCH_CAPACITY_REQ_TIMES_SWITCH:
0,AM_RLC_SPECIAL_HE_COMPATIBLE_SWITC
H:
0,REMOVE_BAND_NOISE_SILENCE_AND_VQI_
SWITCH:0,UL_COMBINE_OPTIMIZE_SWITCH:
0,HSUPA_FASTDELIVER_OPTIMIZE_SWITCH:
0,SRB_OVER_HSDPA_CFN_OPTIMIZE_SWITCH:
0,MACD_4B_MEAS_OPTIMIZE_SWITCH:
0,RACH_PACKET_DISCARD_SWITCH:
0,MACC_PAGING_STAT_OPTI_SWITCH:
0,ERRFRAME_DISCARD_SWITCH:
0,MT_IMPROVE_SWITCH:
0,UP_MAINT_STAT_COUNT_SWITCH:0
TAC_F BSC690 ADD WRFD- Termina Meaning: The function of the TAC.If Fast_Dormancy
UNC 0 UIMEIT 160103 l Black is selected, the TAC specifies the UEs that are enabled
AC WRFD- List with the Fast Dormancy feature; if
MOD 020500 Enhance HSDPA_RB_Setup_Cmp_CRC is selected, the TAC
UIMEIT d Fast specifies that the UEs want to establish services on
AC Dorman HSDPA, however, the RNC sets up services on the
cy DCH, and retries on HSDPA later; if
RMV Special_User_Enhance is selected, the TAC specifies
UIMEIT the UEs that are enabled with the Special User
AC Enhance feature; if Video_Shaping is selected, the
TAC specifies the UEs that are enabled with the Radio
Aware Video Shaping feature. If the RNC receives a
Signaling Connection Release Indication (SCRI)
message from one of this type of UEs during video
service traffic shaping, the RNC keeps the UE in the
CELL_FACH or CELL_PCH state without releasing
the UE's RRC connection.
GUI Value Range: Fast_Dormancy,
HSDPA_RB_Setup_Cmp_CRC,
Special_User_Enhance, Video_Shaping
Unit: None
Actual Value Range: Fast_Dormancy,
HSDPA_RB_Setup_Cmp_CRC,
Special_User_Enhance, Video_Shaping
Default Value: None
TAC_F BSC691 ADD WRFD- Termina Meaning: The function of the TAC.If Fast_Dormancy
UNC 0 UIMEIT 160103 l Black is selected, the TAC specifies the UEs that are enabled
AC WRFD- List with the Fast Dormancy feature; if
MOD 020500 Enhance HSDPA_RB_Setup_Cmp_CRC is selected, the TAC
UIMEIT d Fast specifies that the UEs want to establish services on
AC Dorman HSDPA, however, the RNC sets up services on the
cy DCH, and retries on HSDPA later; if
RMV Special_User_Enhance is selected, the TAC specifies
UIMEIT the UEs that are enabled with the Special User
AC Enhance feature; if Video_Shaping is selected, the
TAC specifies the UEs that are enabled with the Radio
Aware Video Shaping feature. If the RNC receives a
Signaling Connection Release Indication (SCRI)
message from one of this type of UEs during video
service traffic shaping, the RNC keeps the UE in the
CELL_FACH or CELL_PCH state without releasing
the UE's RRC connection.
GUI Value Range: Fast_Dormancy,
HSDPA_RB_Setup_Cmp_CRC,
Special_User_Enhance, Video_Shaping
Unit: None
Actual Value Range: Fast_Dormancy,
HSDPA_RB_Setup_Cmp_CRC,
Special_User_Enhance, Video_Shaping
Default Value: None
6)SPECUSER_NO_RBSETUP_MSG_OPT_SWITC
H(RB SETUP Message Size Reduction Disable
Switch)
Whether to disable the RB SETUP message size
reduction function for special UEs.
1: This switch is turned on and special UEs cannot use
the RB SETUP message size reduction function.
0: This switch is turned off and special UEs can use
the RB SETUP message size reduction function.
7)SPECUSER_REEST_TO_FACH_LIMITATION(R
L Reestablishment on FACH Forbidden for Special
UEs)
Whether to forbid special UEs to reestablish their
radio links (RLs) on the FACH.
1: This switch is turned on, and special UEs cannot
reestablish their RLs on the FACH.
0: This switch is turned off, and special UEs can
reestablish their RLs on the FACH.
8)SPECUSER_WBAMR_RB_RECFG_LIMIT_SWI
TCH(WB-AMR RB RECFG Disable Switch)
Whether to perform the RB RECFG procedure for
special UEs processing AMR-WB or AMR-NB
services.
1: This switch is turned on and the RNC does not
perform the RB RECFG procedure on UEs processing
AMR-WB or AMR-NB services.
0: This switch is turned off and the RNC performs the
RB RECFG procedure on UEs processing AMR-WB
or AMR-NB services.
9)SPECUSER_NO_FAST_RECFG_HHO_SWITCH(
Fast Recfg Prohibit Switch for Special UE in HHO)
Whether to use the asynchronous configuration mode
for a special UE in hard handover scenarios.
1: This switch is turned on and the asynchronous
configuration mode is not used for a specified UE in
hard handover scenarios.
0: This switch is turned off and the asynchronous
configuration mode can be used for a specified UE in
hard handover scenarios.
10)SPECUSER_NO_AMR_NOISE_DETECT_SWIT
CH(UL Garbled Noise Detection and Correction
Inhibition Switch for Special UEs)
SPECUSER_DLRLMAXPWR_RECTIFY_SWITCH,
SPECUSER_SRB_TF_OPT_LIMIT_SWITCH
Unit: None
Actual Value Range:
SPECUSER_4C_HSDPA_LIMIT_SWITCH,
SPECUSER_3C_HSDPA_LIMIT_SWITCH,
SPECUSER_DC_HSDPA_LIMIT_SWITCH,
SPECUSER_DB_HSDPA_LIMIT_SWITCH,
SPECUSER_DC_HSUPA_LIMIT_SWITCH,
SPECUSER_NO_RBSETUP_MSG_OPT_SWITCH,
SPECUSER_REEST_TO_FACH_LIMITATION,
SPECUSER_WBAMR_RB_RECFG_LIMIT_SWITC
H,
SPECUSER_NO_FAST_RECFG_HHO_SWITCH,
SPECUSER_NO_AMR_NOISE_DETECT_SWITCH
,
SPECUSER_NO_HSDPACM_SWITCH,
SPECUSER_NO_HSUPACM_SWITCH,
SPECUSER_NO_EHSPACM_SWITCH,
SPECUSER_GUL_CM_LIMIT_SWITCH,
SPECUSER_SECMOD_CU_OVERLAP_OPT_SWI
TCH,
SPECUSER_SECMOD_CU_OVERLAP_CMP_SWI
TCH,
SPECUSER_DLRLMAXPWR_RECTIFY_SWITCH,
SPECUSER_SRB_TF_OPT_LIMIT_SWITCH
Default Value:
SPECUSER_4C_HSDPA_LIMIT_SWITCH:
0,SPECUSER_3C_HSDPA_LIMIT_SWITCH:
0,SPECUSER_DC_HSDPA_LIMIT_SWITCH:
0,SPECUSER_DB_HSDPA_LIMIT_SWITCH:
0,SPECUSER_DC_HSUPA_LIMIT_SWITCH:
0,SPECUSER_NO_RBSETUP_MSG_OPT_SWITCH
:0,SPECUSER_REEST_TO_FACH_LIMITATION:
0,SPECUSER_WBAMR_RB_RECFG_LIMIT_SWIT
CH:
0,SPECUSER_NO_FAST_RECFG_HHO_SWITCH:
0,SPECUSER_NO_AMR_NOISE_DETECT_SWITC
H:0,SPECUSER_NO_HSDPACM_SWITCH:
0,SPECUSER_NO_HSUPACM_SWITCH:
0,SPECUSER_NO_EHSPACM_SWITCH:
0,SPECUSER_GUL_CM_LIMIT_SWITCH:
0,SPECUSER_SECMOD_CU_OVERLAP_OPT_SW
ITCH:
0,SPECUSER_SECMOD_CU_OVERLAP_CMP_S
WITCH:
0,SPECUSER_DLRLMAXPWR_RECTIFY_SWITC
H:0,SPECUSER_SRB_TF_OPT_LIMIT_SWITCH:0
6)SPECUSER_NO_RBSETUP_MSG_OPT_SWITC
H(RB SETUP Message Size Reduction Disable
Switch)
Whether to disable the RB SETUP message size
reduction function for special UEs.
1: This switch is turned on and special UEs cannot use
the RB SETUP message size reduction function.
0: This switch is turned off and special UEs can use
the RB SETUP message size reduction function.
7)SPECUSER_REEST_TO_FACH_LIMITATION(R
L Reestablishment on FACH Forbidden for Special
UEs)
Whether to forbid special UEs to reestablish their
radio links (RLs) on the FACH.
1: This switch is turned on, and special UEs cannot
reestablish their RLs on the FACH.
0: This switch is turned off, and special UEs can
reestablish their RLs on the FACH.
8)SPECUSER_WBAMR_RB_RECFG_LIMIT_SWI
TCH(WB-AMR RB RECFG Disable Switch)
Whether to perform the RB RECFG procedure for
special UEs processing AMR-WB or AMR-NB
services.
1: This switch is turned on and the RNC does not
perform the RB RECFG procedure on UEs processing
AMR-WB or AMR-NB services.
0: This switch is turned off and the RNC performs the
RB RECFG procedure on UEs processing AMR-WB
or AMR-NB services.
9)SPECUSER_NO_FAST_RECFG_HHO_SWITCH(
Fast Recfg Prohibit Switch for Special UE in HHO)
Whether to use the asynchronous configuration mode
for a special UE in hard handover scenarios.
1: This switch is turned on and the asynchronous
configuration mode is not used for a specified UE in
hard handover scenarios.
0: This switch is turned off and the asynchronous
configuration mode can be used for a specified UE in
hard handover scenarios.
10)SPECUSER_NO_AMR_NOISE_DETECT_SWIT
CH(UL Garbled Noise Detection and Correction
Inhibition Switch for Special UEs)
SPECUSER_DLRLMAXPWR_RECTIFY_SWITCH,
SPECUSER_SRB_TF_OPT_LIMIT_SWITCH
Unit: None
Actual Value Range:
SPECUSER_4C_HSDPA_LIMIT_SWITCH,
SPECUSER_3C_HSDPA_LIMIT_SWITCH,
SPECUSER_DC_HSDPA_LIMIT_SWITCH,
SPECUSER_DB_HSDPA_LIMIT_SWITCH,
SPECUSER_DC_HSUPA_LIMIT_SWITCH,
SPECUSER_NO_RBSETUP_MSG_OPT_SWITCH,
SPECUSER_REEST_TO_FACH_LIMITATION,
SPECUSER_WBAMR_RB_RECFG_LIMIT_SWITC
H,
SPECUSER_NO_FAST_RECFG_HHO_SWITCH,
SPECUSER_NO_AMR_NOISE_DETECT_SWITCH
,
SPECUSER_NO_HSDPACM_SWITCH,
SPECUSER_NO_HSUPACM_SWITCH,
SPECUSER_NO_EHSPACM_SWITCH,
SPECUSER_GUL_CM_LIMIT_SWITCH,
SPECUSER_SECMOD_CU_OVERLAP_OPT_SWI
TCH,
SPECUSER_SECMOD_CU_OVERLAP_CMP_SWI
TCH,
SPECUSER_DLRLMAXPWR_RECTIFY_SWITCH,
SPECUSER_SRB_TF_OPT_LIMIT_SWITCH
Default Value:
SPECUSER_4C_HSDPA_LIMIT_SWITCH:
0,SPECUSER_3C_HSDPA_LIMIT_SWITCH:
0,SPECUSER_DC_HSDPA_LIMIT_SWITCH:
0,SPECUSER_DB_HSDPA_LIMIT_SWITCH:
0,SPECUSER_DC_HSUPA_LIMIT_SWITCH:
0,SPECUSER_NO_RBSETUP_MSG_OPT_SWITCH
:0,SPECUSER_REEST_TO_FACH_LIMITATION:
0,SPECUSER_WBAMR_RB_RECFG_LIMIT_SWIT
CH:
0,SPECUSER_NO_FAST_RECFG_HHO_SWITCH:
0,SPECUSER_NO_AMR_NOISE_DETECT_SWITC
H:0,SPECUSER_NO_HSDPACM_SWITCH:
0,SPECUSER_NO_HSUPACM_SWITCH:
0,SPECUSER_NO_EHSPACM_SWITCH:
0,SPECUSER_GUL_CM_LIMIT_SWITCH:
0,SPECUSER_SECMOD_CU_OVERLAP_OPT_SW
ITCH:
0,SPECUSER_SECMOD_CU_OVERLAP_CMP_S
WITCH:
0,SPECUSER_DLRLMAXPWR_RECTIFY_SWITC
H:0,SPECUSER_SRB_TF_OPT_LIMIT_SWITCH:0
11)UU_ABN_REL_INFO_NOTIFY_NODEB_SWIT
CH
Whether to notify the NodeB of the abnormal RL
release due to poor Uu interface quality.
1: This switch is turned on. The RNC notifies the
NodeB of the abnormal RL release due to poor Uu
interface quality.
0: This switch is turned off. The RNC does not notify
the NodeB of the abnormal RL release due to poor Uu
interface quality.
12)D2F_AM_PROCEDURE_OPTIMIZATION_SWI
TCH
Whether the RNC considers the D2F state transition
as successful if the RNC does not receive a response
message from the UE within the specified period after
sending a RADIO BEARER RECONFIGURTION
message to the UE in acknowledged mode (AM).
1: This switch is turned on. The RNC considers the
D2F state transition as successful if the following
conditions are met:
The RNC does not receive a response from the UE
within the specified period after sending a RADIO
BEARER RECONFIGURATION message to the UE
in AM.
All radio links (RLs) for the UE are out of
synchronization.
The RLCs for all TRBs are in AM.
If any of the preceding conditions is not met, the RNC
undoes the D2F state transition.
0: This switch is turned off. The RNC undoes the D2F
state transition if the RNC does not receive a response
from the UE within the specified period after sending
a RADIO BEARER RECONFIGURATION message
to the UE in AM.
13)AM_D2F_F2D_RESTMR_OPTIMIZATION_SWI
TCH (Response Timer Optimization Switch for D2F
and F2D Procedures in AM)
Length policy for the timer set for the RNC to wait for
a response message from the UE after the RNC sends
a RADIO BEARER RECONFIGURATION message
to the UE in AM during the D2F and F2D state
transitions.
1: This switch is turned on. The length of the timer
equals its configured value (value of the
D2F_PROCEDURE_OPTIMIZATION_SWITCH,
F2D_PROCEDURE_OPTIMIZATION_SWITCH,
FOREVER_PCH_CTRL_PLANE_SHARE_OPT,
FOREVER_PCH_USER_PLANE_SHARE_OPT,
RAB_REL_SRV_CELL_CHG_CROSS_SWITCH,
SCRIWITHCAUSE_OVERLAP_SWITCH,
P2F_CUC_REPEAT_SWITCH,
UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH
,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITC
H,
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITC
H, D2P_DT_MSG_BUFFER_SWITCH,
CM_CODE_CONFLICT_OPT_SWITCH,
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH,
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH,
RLRST_ASU_SUCC_COUNTERS_CORRECT_SW
ITCH,
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH,
RAB_RELATED_COUNTER_OPT_SWITCH,
CELLUPDATE_PROCEDURE_OPT_SWITCH,
PTT_PAGING_PRD_CRRCT_SWITCH,
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITC
H, L2U_UP_DELAY_OPT_SWITCH,
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWI
TCH
Unit: None
Actual Value Range:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH,
RL_REEST_PS_ON_FACH_SWITCH,
CELLUPDATE_MEASUREMENT_OPT_SWITCH,
D2F_PROCEDURE_OPTIMIZATION_SWITCH,
F2D_PROCEDURE_OPTIMIZATION_SWITCH,
FOREVER_PCH_CTRL_PLANE_SHARE_OPT,
FOREVER_PCH_USER_PLANE_SHARE_OPT,
RAB_REL_SRV_CELL_CHG_CROSS_SWITCH,
SCRIWITHCAUSE_OVERLAP_SWITCH,
P2F_CUC_REPEAT_SWITCH,
UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH
,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITC
H,
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITC
H,
D2P_DT_MSG_BUFFER_SWITCH,
CM_CODE_CONFLICT_OPT_SWITCH,
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH,
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH,
RLRST_ASU_SUCC_COUNTERS_CORRECT_SW
ITCH,
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH,
RAB_RELATED_COUNTER_OPT_SWITCH,
CELLUPDATE_PROCEDURE_OPT_SWITCH,
PTT_PAGING_PRD_CRRCT_SWITCH,
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITC
H,
L2U_UP_DELAY_OPT_SWITCH,
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWI
TCH
Default Value:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH:
1,RL_REEST_PS_ON_FACH_SWITCH:
0,CELLUPDATE_MEASUREMENT_OPT_SWITCH
:0,D2F_PROCEDURE_OPTIMIZATION_SWITCH:
0,F2D_PROCEDURE_OPTIMIZATION_SWITCH:
0,FOREVER_PCH_CTRL_PLANE_SHARE_OPT:
0,FOREVER_PCH_USER_PLANE_SHARE_OPT:
0,RAB_REL_SRV_CELL_CHG_CROSS_SWITCH:
0,SCRIWITHCAUSE_OVERLAP_SWITCH:
0,P2F_CUC_REPEAT_SWITCH:
0,UU_ABN_REL_INFO_NOTIFY_NODEB_SWITC
H:
1,D2F_AM_PROCEDURE_OPTIMIZATION_SWIT
CH:
0,AM_D2F_F2D_RESTMR_OPTIMIZATION_SWIT
CH:0,D2P_DT_MSG_BUFFER_SWITCH:
0,CM_CODE_CONFLICT_OPT_SWITCH:
1,H_SERV_CELL_CHANGE_MSG_OPT_SWITCH:
0,FAST_HSDPA_SERV_CELL_CHANGE_SWITCH
:
0,RLRST_ASU_SUCC_COUNTERS_CORRECT_S
WITCH:
0,COUNT_STATE_CHG_BY_RAB_EHN_SWITCH:
0,RAB_RELATED_COUNTER_OPT_SWITCH:
0,CELLUPDATE_PROCEDURE_OPT_SWITCH:
1,PTT_PAGING_PRD_CRRCT_SWITCH:
0,RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWIT
CH:0,L2U_UP_DELAY_OPT_SWITCH:
11)UU_ABN_REL_INFO_NOTIFY_NODEB_SWIT
CH
Whether to notify the NodeB of the abnormal RL
release due to poor Uu interface quality.
1: This switch is turned on. The RNC notifies the
NodeB of the abnormal RL release due to poor Uu
interface quality.
0: This switch is turned off. The RNC does not notify
the NodeB of the abnormal RL release due to poor Uu
interface quality.
12)D2F_AM_PROCEDURE_OPTIMIZATION_SWI
TCH
Whether the RNC considers the D2F state transition
as successful if the RNC does not receive a response
message from the UE within the specified period after
sending a RADIO BEARER RECONFIGURTION
message to the UE in acknowledged mode (AM).
1: This switch is turned on. The RNC considers the
D2F state transition as successful if the following
conditions are met:
The RNC does not receive a response from the UE
within the specified period after sending a RADIO
BEARER RECONFIGURATION message to the UE
in AM.
All radio links (RLs) for the UE are out of
synchronization.
The RLCs for all TRBs are in AM.
If any of the preceding conditions is not met, the RNC
undoes the D2F state transition.
0: This switch is turned off. The RNC undoes the D2F
state transition if the RNC does not receive a response
from the UE within the specified period after sending
a RADIO BEARER RECONFIGURATION message
to the UE in AM.
13)AM_D2F_F2D_RESTMR_OPTIMIZATION_SWI
TCH (Response Timer Optimization Switch for D2F
and F2D Procedures in AM)
Length policy for the timer set for the RNC to wait for
a response message from the UE after the RNC sends
a RADIO BEARER RECONFIGURATION message
to the UE in AM during the D2F and F2D state
transitions.
1: This switch is turned on. The length of the timer
equals its configured value (value of the
D2F_PROCEDURE_OPTIMIZATION_SWITCH,
F2D_PROCEDURE_OPTIMIZATION_SWITCH,
FOREVER_PCH_CTRL_PLANE_SHARE_OPT,
FOREVER_PCH_USER_PLANE_SHARE_OPT,
RAB_REL_SRV_CELL_CHG_CROSS_SWITCH,
SCRIWITHCAUSE_OVERLAP_SWITCH,
P2F_CUC_REPEAT_SWITCH,
UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH
,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITC
H,
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITC
H, D2P_DT_MSG_BUFFER_SWITCH,
CM_CODE_CONFLICT_OPT_SWITCH,
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH,
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH,
RLRST_ASU_SUCC_COUNTERS_CORRECT_SW
ITCH,
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH,
RAB_RELATED_COUNTER_OPT_SWITCH,
CELLUPDATE_PROCEDURE_OPT_SWITCH,
PTT_PAGING_PRD_CRRCT_SWITCH,
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITC
H, L2U_UP_DELAY_OPT_SWITCH,
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWI
TCH
Unit: None
Actual Value Range:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH,
RL_REEST_PS_ON_FACH_SWITCH,
CELLUPDATE_MEASUREMENT_OPT_SWITCH,
D2F_PROCEDURE_OPTIMIZATION_SWITCH,
F2D_PROCEDURE_OPTIMIZATION_SWITCH,
FOREVER_PCH_CTRL_PLANE_SHARE_OPT,
FOREVER_PCH_USER_PLANE_SHARE_OPT,
RAB_REL_SRV_CELL_CHG_CROSS_SWITCH,
SCRIWITHCAUSE_OVERLAP_SWITCH,
P2F_CUC_REPEAT_SWITCH,
UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH
,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITC
H,
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITC
H,
D2P_DT_MSG_BUFFER_SWITCH,
CM_CODE_CONFLICT_OPT_SWITCH,
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH,
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH,
RLRST_ASU_SUCC_COUNTERS_CORRECT_SW
ITCH,
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH,
RAB_RELATED_COUNTER_OPT_SWITCH,
CELLUPDATE_PROCEDURE_OPT_SWITCH,
PTT_PAGING_PRD_CRRCT_SWITCH,
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITC
H,
L2U_UP_DELAY_OPT_SWITCH,
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWI
TCH
Default Value:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH:
1,RL_REEST_PS_ON_FACH_SWITCH:
0,CELLUPDATE_MEASUREMENT_OPT_SWITCH
:0,D2F_PROCEDURE_OPTIMIZATION_SWITCH:
0,F2D_PROCEDURE_OPTIMIZATION_SWITCH:
0,FOREVER_PCH_CTRL_PLANE_SHARE_OPT:
0,FOREVER_PCH_USER_PLANE_SHARE_OPT:
0,RAB_REL_SRV_CELL_CHG_CROSS_SWITCH:
0,SCRIWITHCAUSE_OVERLAP_SWITCH:
0,P2F_CUC_REPEAT_SWITCH:
0,UU_ABN_REL_INFO_NOTIFY_NODEB_SWITC
H:
1,D2F_AM_PROCEDURE_OPTIMIZATION_SWIT
CH:
0,AM_D2F_F2D_RESTMR_OPTIMIZATION_SWIT
CH:0,D2P_DT_MSG_BUFFER_SWITCH:
0,CM_CODE_CONFLICT_OPT_SWITCH:
1,H_SERV_CELL_CHANGE_MSG_OPT_SWITCH:
0,FAST_HSDPA_SERV_CELL_CHANGE_SWITCH
:
0,RLRST_ASU_SUCC_COUNTERS_CORRECT_S
WITCH:
0,COUNT_STATE_CHG_BY_RAB_EHN_SWITCH:
0,RAB_RELATED_COUNTER_OPT_SWITCH:
0,CELLUPDATE_PROCEDURE_OPT_SWITCH:
1,PTT_PAGING_PRD_CRRCT_SWITCH:
0,RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWIT
CH:0,L2U_UP_DELAY_OPT_SWITCH:
NOutsy BSC691 ADD WRFD- Physical Meaning: Number of times of successive in-sync
ncInd 0 UCELL 022000 Channel indications required for starting the radio link failure
SETUP Manage timer. When the radio link set is in the synchronized
MOD ment state, the NodeB starts the timer after it receives
UCELL successive out-of-sync indications of the number
defined by "NOutsyncInd". The NodeB shall stop and
reset the timer after receiving successive in-sync
indications of the number defined by "NInsyncInd".
"TRlFailure" specifies the length of the timer. When
the timer expires, the NodeB triggers the radio link
failure process, and indicates which radio link set is
out-of-sync.
GUI Value Range: 1~256
Unit: None
Actual Value Range: 1~256
Default Value: 50
NOutsy BSC690 ADD WRFD- Physical Meaning: Number of times of successive in-sync
ncInd 0 UCELL 022000 Channel indications required for starting the radio link failure
SETUP Manage timer. When the radio link set is in the synchronized
MOD ment state, the NodeB starts the timer after it receives
UCELL successive out-of-sync indications of the number
defined by "NOutsyncInd". The NodeB shall stop and
reset the timer after receiving successive in-sync
indications of the number defined by "NInsyncInd".
"TRlFailure" specifies the length of the timer. When
the timer expires, the NodeB triggers the radio link
failure process, and indicates which radio link set is
out-of-sync.
GUI Value Range: 1~256
Unit: None
Actual Value Range: 1~256
Default Value: 50
TRlFail BSC690 ADD WRFD- Call Meaning: Radio link failure timer duration. When the
ure 0 UCELL 140103 Reestabl radio link set is in the synchronized state, the NodeB
SETUP WRFD- ishment starts the timer after it receives successive out-of-sync
MOD 022000 Physical indications of the number defined by NOutsyncInd.
UCELL Channel The NodeB shall stop and reset the timer after
Manage receiving successive in-sync indications of the number
ment defined by NInsyncInd. When the timer expires, the
NodeB triggers the radio link failure process, and
indicates which radio link set is out-of-sync.
GUI Value Range: 0~255
Unit: 0.1s
Actual Value Range: 0~25.5
Default Value: 50
TRlFail BSC691 ADD WRFD- Call Meaning: Radio link failure timer duration. When the
ure 0 UCELL 140103 Reestabl radio link set is in the synchronized state, the NodeB
SETUP WRFD- ishment starts the timer after it receives successive out-of-sync
MOD 022000 Physical indications of the number defined by NOutsyncInd.
UCELL Channel The NodeB shall stop and reset the timer after
Manage receiving successive in-sync indications of the number
ment defined by NInsyncInd. When the timer expires, the
NodeB triggers the radio link failure process, and
indicates which radio link set is out-of-sync.
GUI Value Range: 0~255
Unit: 0.1s
Actual Value Range: 0~25.5
Default Value: 50
NInsync BSC690 ADD WRFD- Call Meaning: Number of times of successive in-sync
Ind 0 UCELL 140103 Reestabl indications required for the NodeB to trigger the radio
SETUP WRFD- ishment link recovery process. The radio link set remains in
MOD 022000 Physical the initial state until it has received a number (the
UCELL Channel number is defined by "NInsyncInd") of successive in-
Manage sync indications from L1, and then the NodeB triggers
ment the radio link recovery process, which indicates that
the radio link set has been synchronized. Once the
radio link recovery process is triggered, the radio link
set is considered to be in the synchronized state. In the
radio link maintenance process.
GUI Value Range: 1~256
Unit: None
Actual Value Range: 1~256
Default Value: 5
NInsync BSC691 ADD WRFD- Call Meaning: Number of times of successive in-sync
Ind 0 UCELL 140103 Reestabl indications required for the NodeB to trigger the radio
SETUP WRFD- ishment link recovery process. The radio link set remains in
MOD 022000 Physical the initial state until it has received a number (the
UCELL Channel number is defined by "NInsyncInd") of successive in-
Manage sync indications from L1, and then the NodeB triggers
ment the radio link recovery process, which indicates that
the radio link set has been synchronized. Once the
radio link recovery process is triggered, the radio link
set is considered to be in the synchronized state. In the
radio link maintenance process.
GUI Value Range: 1~256
Unit: None
Actual Value Range: 1~256
Default Value: 5
23) RB_SETUP_CIPHER_TIME_ADJ_SWITCH
Whether the RNC adjusts the activation time for
encryption parameters based on an RB SETUP
COMPLETE message
1: This switch is turned on. The RNC does not adjust
the activation time for encryption parameters as long
as the difference between the activation times
specified in an RB SETUP COMPLETE message and
in the corresponding RB SETUP message is smaller
than 200 connection frame numbers (CFNs).
0: This switch is turned off. The RNC always adjusts
the activation time for encryption parameters based on
an RB SETUP COMPLETE message, regardless of
the preceding difference.
24) CS_PRI_MOD_NOT_INT_SWITCH
Whether the RNC re-initiates CS services upon
receiving a RAB ASSIGNMENT REQUEST message
in which only the CS allocation/retention priority
(CARP) is changed.
1: This switch is turned on. The RNC does not re-
initiate CS services, which prevents CS call drops.
0: This switch is turned off. The RNC re-initiates CS
services, which results in CS call drops.
25)
RAB_SETUP_TMSI_REALLOC_BUF_SWITCH
Whether the RNC buffers a TMSI REALLOCATION
COMMAND message received during an RAB setup.
1: This switch is turned on. The RNC buffers the
TMSI REALLOCATION COMMAND message
received during the RAB setup and then forwards the
message to a UE after the RAB setup.
0: This switch is turned off. The RNC does not buffer
the TMSI REALLOCATION COMMAND message
received during the RAB setup. The RNC directly
forwards the message to a UE.
26) IU_FAULT_REL_PS_RES_SWITCH
Whether an UCP subsystem sends a PS service release
message to an Iu-PS interface board in case of a faulty
IP path, a faulty Signaling Connection Control Part
(SCCP) link, or a reset on the Iu interface
1: This switch is turned on. The UCP subsystem sends
the PS service release message to the Iu-PS interface
board.
RB_SETUP_CIPHER_TIME_ADJ_SWITCH,
CS_PRI_MOD_NOT_INT_SWITCH,
RAB_SETUP_TMSI_REALLOC_BUF_SWITCH,
IU_FAULT_REL_PS_RES_SWITCH,
RB_RECFG_RL_REEST_SWITCH,
F2P_DT_MSG_BUFFER_SWITCH,
SCRI_COMPATIBLE_SWITCH,
GTPU_ERR_IND_DEF_SWITCH,
IUR_SRV_CELL_CHG_MACHS_RESET_SWITCH,
UL_INTEG_ALGO_COMPAT_SWITCH
Unit: None
Actual Value Range:
PAGGING_NUM_CTRL_SWITCH,
ASU_RL_RESET_SWITCH,
MC_RL_RESET_SWITCH,
FD_PCH_REENTERSA_FORCE_RRC_REL_SWIT
CH,
UE_CRC_COMPATIBLE_SWITCH,
RNC_P2D_DRD_SWITCH,
P2D_SWITCH,
AMR_F2D_OVERLAP_CELLUPT_SWITCH,
SRB_RESET_RL_SETUP_SWITCH,
RLFAIL_RL_SETUP_SWITCH,
CS_RL_SETUP_SWITCH,
PS_RL_SETUP_SWITCH,
UE_SRB_RESET_SWITCH,
RL_RESTORE_SWITCH,
RNC_EFD_D2F_SWITCH,
RNC_RB_SCRI_NOT_DROP_SWITCH,
RRC_RECONN_SWITCH,
RRC_REPEAT_PFM_SWITCH,
F2D_NO_RSP_RRCREL_SWITCH,
CS_SETUP_P2D_SWITCH,
SYSHO_CIPHER_IE_SWITCH,
P2P_GTPU_NOT_CFG_SWITCH,
RB_SETUP_CIPHER_TIME_ADJ_SWITCH,
CS_PRI_MOD_NOT_INT_SWITCH,
RAB_SETUP_TMSI_REALLOC_BUF_SWITCH,
IU_FAULT_REL_PS_RES_SWITCH,
RB_RECFG_RL_REEST_SWITCH,
F2P_DT_MSG_BUFFER_SWITCH,
SCRI_COMPATIBLE_SWITCH,
GTPU_ERR_IND_DEF_SWITCH,
IUR_SRV_CELL_CHG_MACHS_RESET_SWITCH,
UL_INTEG_ALGO_COMPAT_SWITCH
Default Value: PAGGING_NUM_CTRL_SWITCH:
0,ASU_RL_RESET_SWITCH:
0,MC_RL_RESET_SWITCH:
0,FD_PCH_REENTERSA_FORCE_RRC_REL_SWI
TCH:0,UE_CRC_COMPATIBLE_SWITCH:
0,RNC_P2D_DRD_SWITCH:0,P2D_SWITCH:
0,AMR_F2D_OVERLAP_CELLUPT_SWITCH:
0,SRB_RESET_RL_SETUP_SWITCH:
0,RLFAIL_RL_SETUP_SWITCH:
0,CS_RL_SETUP_SWITCH:
0,PS_RL_SETUP_SWITCH:
0,UE_SRB_RESET_SWITCH:
0,RL_RESTORE_SWITCH:
0,RNC_EFD_D2F_SWITCH:
1,RNC_RB_SCRI_NOT_DROP_SWITCH:
0,RRC_RECONN_SWITCH:
0,RRC_REPEAT_PFM_SWITCH:
1,F2D_NO_RSP_RRCREL_SWITCH:
0,CS_SETUP_P2D_SWITCH:
0,SYSHO_CIPHER_IE_SWITCH:
0,P2P_GTPU_NOT_CFG_SWITCH:
1,RB_SETUP_CIPHER_TIME_ADJ_SWITCH:
1,CS_PRI_MOD_NOT_INT_SWITCH:
0,RAB_SETUP_TMSI_REALLOC_BUF_SWITCH:
0,IU_FAULT_REL_PS_RES_SWITCH:
0,RB_RECFG_RL_REEST_SWITCH:
0,F2P_DT_MSG_BUFFER_SWITCH:
0,SCRI_COMPATIBLE_SWITCH:
0,GTPU_ERR_IND_DEF_SWITCH:
0,IUR_SRV_CELL_CHG_MACHS_RESET_SWITC
H:1,UL_INTEG_ALGO_COMPAT_SWITCH:0
23) RB_SETUP_CIPHER_TIME_ADJ_SWITCH
Whether the RNC adjusts the activation time for
encryption parameters based on an RB SETUP
COMPLETE message
1: This switch is turned on. The RNC does not adjust
the activation time for encryption parameters as long
as the difference between the activation times
specified in an RB SETUP COMPLETE message and
in the corresponding RB SETUP message is smaller
than 200 connection frame numbers (CFNs).
0: This switch is turned off. The RNC always adjusts
the activation time for encryption parameters based on
an RB SETUP COMPLETE message, regardless of
the preceding difference.
24) CS_PRI_MOD_NOT_INT_SWITCH
Whether the RNC re-initiates CS services upon
receiving a RAB ASSIGNMENT REQUEST message
in which only the CS allocation/retention priority
(CARP) is changed.
1: This switch is turned on. The RNC does not re-
initiate CS services, which prevents CS call drops.
0: This switch is turned off. The RNC re-initiates CS
services, which results in CS call drops.
25)
RAB_SETUP_TMSI_REALLOC_BUF_SWITCH
Whether the RNC buffers a TMSI REALLOCATION
COMMAND message received during an RAB setup.
1: This switch is turned on. The RNC buffers the
TMSI REALLOCATION COMMAND message
received during the RAB setup and then forwards the
message to a UE after the RAB setup.
0: This switch is turned off. The RNC does not buffer
the TMSI REALLOCATION COMMAND message
received during the RAB setup. The RNC directly
forwards the message to a UE.
26) IU_FAULT_REL_PS_RES_SWITCH
Whether an UCP subsystem sends a PS service release
message to an Iu-PS interface board in case of a faulty
IP path, a faulty Signaling Connection Control Part
(SCCP) link, or a reset on the Iu interface
1: This switch is turned on. The UCP subsystem sends
the PS service release message to the Iu-PS interface
board.
RB_SETUP_CIPHER_TIME_ADJ_SWITCH,
CS_PRI_MOD_NOT_INT_SWITCH,
RAB_SETUP_TMSI_REALLOC_BUF_SWITCH,
IU_FAULT_REL_PS_RES_SWITCH,
RB_RECFG_RL_REEST_SWITCH,
F2P_DT_MSG_BUFFER_SWITCH,
SCRI_COMPATIBLE_SWITCH,
GTPU_ERR_IND_DEF_SWITCH,
IUR_SRV_CELL_CHG_MACHS_RESET_SWITCH,
UL_INTEG_ALGO_COMPAT_SWITCH
Unit: None
Actual Value Range:
PAGGING_NUM_CTRL_SWITCH,
ASU_RL_RESET_SWITCH,
MC_RL_RESET_SWITCH,
FD_PCH_REENTERSA_FORCE_RRC_REL_SWIT
CH,
UE_CRC_COMPATIBLE_SWITCH,
RNC_P2D_DRD_SWITCH,
P2D_SWITCH,
AMR_F2D_OVERLAP_CELLUPT_SWITCH,
SRB_RESET_RL_SETUP_SWITCH,
RLFAIL_RL_SETUP_SWITCH,
CS_RL_SETUP_SWITCH,
PS_RL_SETUP_SWITCH,
UE_SRB_RESET_SWITCH,
RL_RESTORE_SWITCH,
RNC_EFD_D2F_SWITCH,
RNC_RB_SCRI_NOT_DROP_SWITCH,
RRC_RECONN_SWITCH,
RRC_REPEAT_PFM_SWITCH,
F2D_NO_RSP_RRCREL_SWITCH,
CS_SETUP_P2D_SWITCH,
SYSHO_CIPHER_IE_SWITCH,
P2P_GTPU_NOT_CFG_SWITCH,
RB_SETUP_CIPHER_TIME_ADJ_SWITCH,
CS_PRI_MOD_NOT_INT_SWITCH,
RAB_SETUP_TMSI_REALLOC_BUF_SWITCH,
IU_FAULT_REL_PS_RES_SWITCH,
RB_RECFG_RL_REEST_SWITCH,
F2P_DT_MSG_BUFFER_SWITCH,
SCRI_COMPATIBLE_SWITCH,
GTPU_ERR_IND_DEF_SWITCH,
IUR_SRV_CELL_CHG_MACHS_RESET_SWITCH,
UL_INTEG_ALGO_COMPAT_SWITCH
Default Value: PAGGING_NUM_CTRL_SWITCH:
0,ASU_RL_RESET_SWITCH:
0,MC_RL_RESET_SWITCH:
0,FD_PCH_REENTERSA_FORCE_RRC_REL_SWI
TCH:0,UE_CRC_COMPATIBLE_SWITCH:
0,RNC_P2D_DRD_SWITCH:0,P2D_SWITCH:
0,AMR_F2D_OVERLAP_CELLUPT_SWITCH:
0,SRB_RESET_RL_SETUP_SWITCH:
0,RLFAIL_RL_SETUP_SWITCH:
0,CS_RL_SETUP_SWITCH:
0,PS_RL_SETUP_SWITCH:
0,UE_SRB_RESET_SWITCH:
0,RL_RESTORE_SWITCH:
0,RNC_EFD_D2F_SWITCH:
1,RNC_RB_SCRI_NOT_DROP_SWITCH:
0,RRC_RECONN_SWITCH:
0,RRC_REPEAT_PFM_SWITCH:
1,F2D_NO_RSP_RRCREL_SWITCH:
0,CS_SETUP_P2D_SWITCH:
0,SYSHO_CIPHER_IE_SWITCH:
0,P2P_GTPU_NOT_CFG_SWITCH:
1,RB_SETUP_CIPHER_TIME_ADJ_SWITCH:
1,CS_PRI_MOD_NOT_INT_SWITCH:
0,RAB_SETUP_TMSI_REALLOC_BUF_SWITCH:
0,IU_FAULT_REL_PS_RES_SWITCH:
0,RB_RECFG_RL_REEST_SWITCH:
0,F2P_DT_MSG_BUFFER_SWITCH:
0,SCRI_COMPATIBLE_SWITCH:
0,GTPU_ERR_IND_DEF_SWITCH:
0,IUR_SRV_CELL_CHG_MACHS_RESET_SWITC
H:1,UL_INTEG_ALGO_COMPAT_SWITCH:0
RlRstrT BSC690 SET WRFD- 3GPP Meaning: A timer to RNC wait for radio link
mr 0 USTAT 010101 R9 restoration indication in the radio link procedure.
ETIME WRFD- Specific GUI Value Range: 100~300000
R 140103 ations
Unit: ms
Call
Reestabl Actual Value Range: 100~300000
ishment Default Value: 11000
RlRstrT BSC691 SET WRFD- 3GPP Meaning: A timer to RNC wait for radio link
mr 0 USTAT 010101 R9 restoration indication in the radio link procedure.
ETIME WRFD- Specific GUI Value Range: 100~300000
R 140103 ations
Unit: ms
Call
Reestabl Actual Value Range: 100~300000
ishment Default Value: 11000
T313 BSC690 SET WRFD- 3GPP Meaning: Timer 313. T313 starts when a UE detects
0 UCONN 010101 R9 N313 successive "out of sync" indications from Layer
MODET WRFD- Specific 1 and stops when the UE detects N315 successive "in
IMER 140103 ations sync" indications form Layer 1. When T313 expires,
Call the radio link setup fails. The protocol-defined default
WRFD- value is 3. The value of this parameter is contained in
010802 Reestabl
ishment SIB1 messages.
WRFD- GUI Value Range: 0~15
010801 Inter
RNC Unit: s
Cell Actual Value Range: 0~15
Update
Default Value: 3
Intra
RNC
Cell
Update
T313 BSC691 SET WRFD- 3GPP Meaning: Timer 313. T313 starts when a UE detects
0 UCONN 010101 R9 N313 successive "out of sync" indications from Layer
MODET WRFD- Specific 1 and stops when the UE detects N315 successive "in
IMER 140103 ations sync" indications form Layer 1. When T313 expires,
Call the radio link setup fails. The protocol-defined default
WRFD- value is 3. The value of this parameter is contained in
010802 Reestabl
ishment SIB1 messages.
WRFD- GUI Value Range: 0~15
010801 Inter
RNC Unit: s
Cell Actual Value Range: 0~15
Update
Default Value: 3
Intra
RNC
Cell
Update
13)
PS_HHO_ASYNC_CTRL_SWITCH(Asynchronous
Reconfigure Switch for PS HHO)
1: This switch is turned on. The RNC does not put the
activation time information element (IE) in the hard
handover configuration message for PS services. After
receiving the message, the UE immediately activates
the configuration.
0: This switch is turned off. The RNC puts the
activation time IE in the hard handover configuration
message for PS services. After receiving the message,
the UE activates the configuration at the specified
activation time.
14)
IUR_HHO_ASYNC_CTRL_SWITCH(Asynchronous
Reconfigure Switch for Iur HHO)
1: This switch is turned on. The RNC does not put the
activation time information element (IE) in the hard
handover configuration message across the Iur
interface. After receiving the message, the UE
immediately activates the configuration.
0: This switch is turned off. The RNC puts the
activation time IE in the hard handover configuration
message across the Iur interface. After receiving the
message, the UE activates the configuration at the
specified activation time.
15) R8_UE_SEL_DPUE_SWITCH (Switch for
Preferentially Allocating DPUe Resources to UEs
That Comply with 3GPP Release 8 or Later)
1: This switch is turned on. The RNC preferentially
allocates DPUe resources in any subrack to UEs that
comply with 3GPP Release 8 or later.
0: This switch is turned off. The RNC preferentially
allocates DPU resources in the subrack that the UEs
access to UEs that comply with 3GPP Release 8 or
later. The RNC allocates DPU resources in other
subracks only when the amount of consumed DPU
resources in this subrack exceeds a preset threshold
for inter-subrack resource sharing.
16)
F2P_DATATRANS_OPTIMIZE_SWITCH(Switch for
Optimized Data Transmission before a State
Transition from CELL_FACH to CELL_PCH or
URA_PCH)
IUR_RL_REEST_SWITCH,
RB_SETUP_RL_REEST_SWITCH,
RRC_CONN_SETUP_OPT_SWITCH,
TCP_ACK_ACCELERATOR_SWITCH,
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITC
H, SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
R8_UE_SEL_DPUE_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEER-
ROR_SWITCH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWITC
H, UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWIT
CH, CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWI
TCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Unit: None
Actual Value Range:
PS_F2D_OVERLAP_CELLUPT_SWITCH,
AMR_HHO_FAIL_ROLLBACK_SWITCH,
PHY_RECFG_REEST_SWITCH,
IUR_RL_REEST_SWITCH,
RB_SETUP_RL_REEST_SWITCH,
RRC_CONN_SETUP_OPT_SWITCH,
TCP_ACK_ACCELERATOR_SWITCH,
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITC
H, SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
R8_UE_SEL_DPUE_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEER-
ROR_SWITCH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWITC
H, UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWIT
CH,
CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWI
TCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Default Value:
PS_F2D_OVERLAP_CELLUPT_SWITCH:
0,AMR_HHO_FAIL_ROLLBACK_SWITCH:
0,PHY_RECFG_REEST_SWITCH:
0,IUR_RL_REEST_SWITCH:
0,RB_SETUP_RL_REEST_SWITCH:
0,RRC_CONN_SETUP_OPT_SWITCH:
0,TCP_ACK_ACCELERATOR_SWITCH:
0,RRC_CELLFACH_TRB_RESET_TO_F2D_SWIT
CH:0,SEND_MSG_NULL_SWITCH:
0,FD_PCH_IUR_CS_OPT_SWITCH:
0,CELLUPT_T314_T315_TIMEOUT_OPT_SWITC
H:0,CS_HHO_ASYNC_CTRL_SWITCH:
0,PS_HHO_ASYNC_CTRL_SWITCH:
0,IUR_HHO_ASYNC_CTRL_SWITCH:
0,R8_UE_SEL_DPUE_SWITCH:
0,F2P_DATATRANS_OPTIMIZE_SWITCH:
0,IRATHO_HOCANCEL_RL_REEST_SWITCH:
0,TRB_RESET_RL_REEST_SWITCH:
0,RB_REL_RL_REEST_SWITCH:
0,RB_SETUP_ENHANCE_RL_REEST_SWITCH:
0,RAB_SETUPMOD_CNT_FIX_SWITCH:
0,PCH_UE_RLC_UNRECOVERABLEER-
ROR_SWITCH:
0,FAST_RETURN_LTE_BY_CELL_SELECT_SWIT
CH:
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEER-
ROR_SWITCH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWITC
H, UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWIT
CH, CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWI
TCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Unit: None
Actual Value Range:
PS_F2D_OVERLAP_CELLUPT_SWITCH,
AMR_HHO_FAIL_ROLLBACK_SWITCH,
PHY_RECFG_REEST_SWITCH,
IUR_RL_REEST_SWITCH,
RB_SETUP_RL_REEST_SWITCH,
RRC_CONN_SETUP_OPT_SWITCH,
TCP_ACK_ACCELERATOR_SWITCH,
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITC
H, SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEER-
ROR_SWITCH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWITC
H, UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWIT
CH,
CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWI
TCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Default Value:
PS_F2D_OVERLAP_CELLUPT_SWITCH:
0,AMR_HHO_FAIL_ROLLBACK_SWITCH:
0,PHY_RECFG_REEST_SWITCH:
0,IUR_RL_REEST_SWITCH:
0,RB_SETUP_RL_REEST_SWITCH:
0,RRC_CONN_SETUP_OPT_SWITCH:
0,TCP_ACK_ACCELERATOR_SWITCH:
0,RRC_CELLFACH_TRB_RESET_TO_F2D_SWIT
CH:0,SEND_MSG_NULL_SWITCH:
0,FD_PCH_IUR_CS_OPT_SWITCH:
0,CELLUPT_T314_T315_TIMEOUT_OPT_SWITC
H:0,CS_HHO_ASYNC_CTRL_SWITCH:
0,PS_HHO_ASYNC_CTRL_SWITCH:
0,IUR_HHO_ASYNC_CTRL_SWITCH:
0,F2P_DATATRANS_OPTIMIZE_SWITCH:
0,IRATHO_HOCANCEL_RL_REEST_SWITCH:
0,TRB_RESET_RL_REEST_SWITCH:
0,RB_REL_RL_REEST_SWITCH:
0,RB_SETUP_ENHANCE_RL_REEST_SWITCH:
0,RAB_SETUPMOD_CNT_FIX_SWITCH:
0,PCH_UE_RLC_UNRECOVERABLEER-
ROR_SWITCH:
0,FAST_RETURN_LTE_BY_CELL_SELECT_SWIT
CH:
0,UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH:
0,PHYCHRECFG_ENH_RL_REEST_SWITCH:
0,RBRECFG_ENH_RL_REEST_SWITCH:
0,SMC_STOP_RLC_SWITCH:
1,GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWI
TCH:1,CMP_IU_QOS_GTP_PDU_SN_SWITCH:
0,DL_TRB_RESET_BUFF_SWITCH:
0,RRC_CELLFACH_DL_TRB_RESET_TO_F2D_S
WITCH:
0,RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH:1
Intra 4)ROUT_IDT_BY_ROUTING_PARA_SWITCH
RNC Whether to enable the RNC to select a CN node based
Cell on the "Routing parameter" IE included in the
Update INITIAL DIRECT TRANSFER message exchanged
Inter every time a CS service is set up for CS+PS combined
RNC services when Iu Flex is applied.
Cell 1: This switch is turned on. The RNC selects a CN
Update node in the preceding way.
Encrypti 0: This switch is turned off. The RNC selects a CN
on node based on the "Routing parameter" IE included in
Combin the INITIAL DIRECT TRANSFER message
ation of exchanged the first time a CS service is set up for CS
One CS +PS combined services if Iu Flex is applied.
Service 5)COUNT_CS_REC_IU_REL_CMD_SWITCH
and
Whether to increase the values of specific counters by
Three
one when the RNC receives an IU RELEASE
PS
COMMAND message from the CS domain and an
Services
inter-RAT handover for CS+PS combined services is
in progress. These counters are VS.CS.Erlang.RNC,
VS.AMR.Erlang.BestCell, VS.RB.AMR.UL.4.75, and
VS.RB.AMR.DL.4.75.
1: This switch is turned on. The values of the
previously mentioned counters are increased by one in
the preceding scenario.
0: This switch is turned off. The values of these
counters are increased by one when the RNC receives
an IU RELEASE COMMAND message from the CS
and PS domains of the CN and an inter-RAT handover
for CS+PS combined services is in progress.
6)SEND_UE_CAP_ENQ_RELOC_CCH_SWITCH
Whether to refuse to send a UE CAPABILITY
ENQUIRY message to a UE that is not in the
CELL_DCH state and is performing an incoming
SRNS relocation.
1: This switch is turned on. The RNC does not send
the message to the UE.
0: This switch is turned off. The RNC sends the
message to the UE.
7)REL_IUR_CCH_BEFORE_DSCR_SWITCH
Whether to immediately release the data of a UE from
an Iur common channel if the UE initiates the DSCR
process.
1: This switch is turned on. The RNC immediately
releases the data of a UE from an Iur common channel
if the UE initiates the DSCR process.
16)PSHO_CSFB_UE_CAP_ENQ_DELAY_SWITCH
Whether to query the UE capability at a delayed time
in the case of a PS HO-based CSFB.
1: This switch is turned on. The RNC queries the UE
capability at a delayed time in the case of a PS HO-
based CSFB. That is, the RNC queries the UE
capability after the CS service is set up.
0: This switch is turned off. The RNC queries the UE
capability during the PS HO-based CSFB.
17)PAGING_OM_OPTIMIZE_SWITCH(Paging
Optimization Switch)
Whether the RNC records the international mobile
subscriber identity (IMSI) of a UE in the idle mode
when the UE does not respond to a CS paging in time
and the cause value carried in the CS paging message
is Terminating Conversational Call, Terminating Low
Priority Signalling, or Terminating Streaming Call.
1: This switch is turned on. The RNC records the
IMSI of the UE in the preceding scenario.
0: This switch is turned off. The RNC does not record
the IMSI of the UE in the preceding scenario.
18)DEACTIVE_CELLHSPA_H2F_SWITCH(H2F
Control Switch After HSPA Deactivated)
Whether to transition UEs processing HSPA services
to the CELL_FACH state or release these UEs after
the HSPA function is deactivated in a cell.
1: This switch is turned on. UEs processing HSPA
services transition to the CELL_FACH state after the
HSPA function is deactivated in the cell.
0: This switch is turned off. UEs processing HSPA
services are released after the HSPA function is
deactivated in the cell.
19)OMIT_UE_CAP_ENQ_RELOC_DCH_SWITCH
Whether the RNC sends a UE CAPABILITY
ENQUIRY message to a UE in the CELL_DCH state
during an incoming relocation procedure.
1: This switch is turned on. Under this circumstance,
the RNC does not send a UE CAPABILITY
ENQUIRY message to a UE in the CELL_DCH state
during an incoming relocation procedure.
0: This switch is turned off. Under this circumstance,
the RNC sends a UE CAPABILITY ENQUIRY
message to a UE in the CELL_DCH state in the
preceding scenario.
20)RAB_SETUP_CNT_CORRECT_SWITCH
Whether to measure the number of RAB setup
attempts when the cross processing of RAB setup and
cell update fails or the radio link reestablishment
triggered by RAB setup fails.
1: This switch is turned on. The number of RAB setup
attempts is measured.
0: This switch is turned off. The number of RAB setup
attempts is not measured.
21)FACH_DCCH_RRC_REL_NO_RSP_DELAY_US
E_URNTI
Whether to delay the assignment of the URNTI from
one UE to another when the timer for the UE to wait
for a response message from the RNC expires after the
UE in the CELL_FACH state sends an RRC
CONNECTION RELEASE message on the DCCH.
This switch prevents the assignment of the URNTI
from one UE to another to avoid URNTI conflicts.
This switch is turned on by default.
1: This switch is turned on. The RNC delays the
assignment of the URNTI from the current UE to
another UE.
0: This switch is turned off. The RNC immediately
assigns the URNTI from the current UE to another
UE.
22)FACH_CCCH_RRC_REL_NO_RSP_DELAY_US
E_URNTI
Whether to delay the assignment of the URNTI from
one UE to another when the timer for the UE to wait
for a response message from the RNC expires after the
UE in the CELL_FACH state sends an RRC
CONNECTION RELEASE message on the CCCH.
This switch prevents the assignment of the URNTI
from one UE to another to avoid URNTI conflicts.
This switch is turned off by default.
1: This switch is turned on. The RNC delays the
assignment of the URNTI from the current UE to
another UE.
0: This switch is turned off. The RNC immediately
assigns the URNTI from the current UE to another
UE.
23)RB_SETUP_RLC_INFO_OPT_SWITCH
Whether the RNC sets the "RLC info" IE of the "RB
information to setup" IE contained in the second and
third RB sub-flows to "Same as RB:0xM" if the RLC
SEND_UE_CAP_ENQ_RELOC_CCH_SWITCH,
REL_IUR_CCH_BEFORE_DSCR_SWITCH,
RELOC_CIPHER_PENDING_COMPATI_SWITCH,
COUNT_SPECIAL_RAB_ATT_SWITCH,
COUNT_STATE_CHG_BY_RAB_SWITCH,
DELAY_SEND_MEACTRL_SWITCH,
TAKE_ACTIVE_TIME_DRD_SWITCH,
CS_DISCONNECT_OPT_SWITCH,
NON_DCCC_RBRECFG_RL_REEST_SWITCH,
SMC_RL_REEST_SWITCH,
PSHO_CSFB_UE_CAP_ENQ_DELAY_SWITCH,
PAGING_OM_OPTIMIZE_SWITCH,
DEACTIVE_CELLHSPA_H2F_SWITCH,
OMIT_UE_CAP_ENQ_RELOC_DCH_SWITCH,
RAB_SETUP_CNT_CORRECT_SWITCH,
FACH_DCCH_RRC_REL_NO_RSP_DELAY_USE_
URNTI,
FACH_CCCH_RRC_REL_NO_RSP_DELAY_USE_
URNTI, RB_SETUP_RLC_INFO_OPT_SWITCH,
DCH_DISCARD_CELL_RESEL_CU_MSG_SWITC
H,
SYS_INIT_SPU_STATE_BROADCAST_OPT_SWI
TCH,
RB_RECFG_F2D_ISR_IC_FAIL_RRC_REL_SWIT
CH,
PTT_RAB_SETUP_ATT_CNT_CORRECT_SWITC
H,
P2D_DRD_FAIL_BACK_RESEL_CELL_SWITCH,
TRB_RST_CU_NOT_REEST_UM_RLC_TRB_SWI
TCH,
ONE_CNNODE_SCCP_CONG_SEL_OTHER_SWI
TCH, CSFB_UE_DELAY_RAU_SWITCH,
CSFB_UE_CS_IMEI_QUERY_DISABLE_SWITCH
Unit: None
Actual Value Range:
CONVERT_RELOC_FAIL_CAUSE_SWITCH,
DEAL_SRNS_CONTEXT_REQ_FIRST_SWITCH,
DELAY_DRNC_CODE_REL_SWITCH,
ROUT_IDT_BY_ROUTING_PARA_SWITCH,
COUNT_CS_REC_IU_REL_CMD_SWITCH,
SEND_UE_CAP_ENQ_RELOC_CCH_SWITCH,
REL_IUR_CCH_BEFORE_DSCR_SWITCH,
RELOC_CIPHER_PENDING_COMPATI_SWITCH,
COUNT_SPECIAL_RAB_ATT_SWITCH,
COUNT_STATE_CHG_BY_RAB_SWITCH,
DELAY_SEND_MEACTRL_SWITCH,
TAKE_ACTIVE_TIME_DRD_SWITCH,
CS_DISCONNECT_OPT_SWITCH,
NON_DCCC_RBRECFG_RL_REEST_SWITCH,
SMC_RL_REEST_SWITCH,
PSHO_CSFB_UE_CAP_ENQ_DELAY_SWITCH,
PAGING_OM_OPTIMIZE_SWITCH,
DEACTIVE_CELLHSPA_H2F_SWITCH,
OMIT_UE_CAP_ENQ_RELOC_DCH_SWITCH,
RAB_SETUP_CNT_CORRECT_SWITCH,
FACH_DCCH_RRC_REL_NO_RSP_DELAY_USE_
URNTI,
FACH_CCCH_RRC_REL_NO_RSP_DELAY_USE_
URNTI,
RB_SETUP_RLC_INFO_OPT_SWITCH,
DCH_DISCARD_CELL_RESEL_CU_MSG_SWITC
H,
SYS_INIT_SPU_STATE_BROADCAST_OPT_SWI
TCH,
RB_RECFG_F2D_ISR_IC_FAIL_RRC_REL_SWIT
CH,
PTT_RAB_SETUP_ATT_CNT_CORRECT_SWITC
H,
P2D_DRD_FAIL_BACK_RESEL_CELL_SWITCH,
TRB_RST_CU_NOT_REEST_UM_RLC_TRB_SWI
TCH,
ONE_CNNODE_SCCP_CONG_SEL_OTHER_SWI
TCH,
CSFB_UE_DELAY_RAU_SWITCH,
CSFB_UE_CS_IMEI_QUERY_DISABLE_SWITCH
Default Value:
CONVERT_RELOC_FAIL_CAUSE_SWITCH:
0,DEAL_SRNS_CONTEXT_REQ_FIRST_SWITCH:
0,DELAY_DRNC_CODE_REL_SWITCH:
0,ROUT_IDT_BY_ROUTING_PARA_SWITCH:
0,COUNT_CS_REC_IU_REL_CMD_SWITCH:
0,SEND_UE_CAP_ENQ_RELOC_CCH_SWITCH:
0,REL_IUR_CCH_BEFORE_DSCR_SWITCH:
0,RELOC_CIPHER_PENDING_COMPATI_SWITC
H:0,COUNT_SPECIAL_RAB_ATT_SWITCH:
0 ,COUNT_STATE_CHG_BY_RAB_SWITCH:
0 ,DELAY_SEND_MEACTRL_SWITCH:
Intra 4)ROUT_IDT_BY_ROUTING_PARA_SWITCH
RNC Whether to enable the RNC to select a CN node based
Cell on the "Routing parameter" IE included in the
Update INITIAL DIRECT TRANSFER message exchanged
Inter every time a CS service is set up for CS+PS combined
RNC services when Iu Flex is applied.
Cell 1: This switch is turned on. The RNC selects a CN
Update node in the preceding way.
Encrypti 0: This switch is turned off. The RNC selects a CN
on node based on the "Routing parameter" IE included in
Combin the INITIAL DIRECT TRANSFER message
ation of exchanged the first time a CS service is set up for CS
One CS +PS combined services if Iu Flex is applied.
Service 5)COUNT_CS_REC_IU_REL_CMD_SWITCH
and
Whether to increase the values of specific counters by
Three
one when the RNC receives an IU RELEASE
PS
COMMAND message from the CS domain and an
Services
inter-RAT handover for CS+PS combined services is
in progress. These counters are VS.CS.Erlang.RNC,
VS.AMR.Erlang.BestCell, VS.RB.AMR.UL.4.75, and
VS.RB.AMR.DL.4.75.
1: This switch is turned on. The values of the
previously mentioned counters are increased by one in
the preceding scenario.
0: This switch is turned off. The values of these
counters are increased by one when the RNC receives
an IU RELEASE COMMAND message from the CS
and PS domains of the CN and an inter-RAT handover
for CS+PS combined services is in progress.
6)SEND_UE_CAP_ENQ_RELOC_CCH_SWITCH
Whether to refuse to send a UE CAPABILITY
ENQUIRY message to a UE that is not in the
CELL_DCH state and is performing an incoming
SRNS relocation.
1: This switch is turned on. The RNC does not send
the message to the UE.
0: This switch is turned off. The RNC sends the
message to the UE.
7)REL_IUR_CCH_BEFORE_DSCR_SWITCH
Whether to immediately release the data of a UE from
an Iur common channel if the UE initiates the DSCR
process.
1: This switch is turned on. The RNC immediately
releases the data of a UE from an Iur common channel
if the UE initiates the DSCR process.
16)PSHO_CSFB_UE_CAP_ENQ_DELAY_SWITCH
Whether to query the UE capability at a delayed time
in the case of a PS HO-based CSFB.
1: This switch is turned on. The RNC queries the UE
capability at a delayed time in the case of a PS HO-
based CSFB. That is, the RNC queries the UE
capability after the CS service is set up.
0: This switch is turned off. The RNC queries the UE
capability during the PS HO-based CSFB.
17)PAGING_OM_OPTIMIZE_SWITCH(Paging
Optimization Switch)
Whether the RNC records the international mobile
subscriber identity (IMSI) of a UE in the idle mode
when the UE does not respond to a CS paging in time
and the cause value carried in the CS paging message
is Terminating Conversational Call, Terminating Low
Priority Signalling, or Terminating Streaming Call.
1: This switch is turned on. The RNC records the
IMSI of the UE in the preceding scenario.
0: This switch is turned off. The RNC does not record
the IMSI of the UE in the preceding scenario.
18)DEACTIVE_CELLHSPA_H2F_SWITCH(H2F
Control Switch After HSPA Deactivated)
Whether to transition UEs processing HSPA services
to the CELL_FACH state or release these UEs after
the HSPA function is deactivated in a cell.
1: This switch is turned on. UEs processing HSPA
services transition to the CELL_FACH state after the
HSPA function is deactivated in the cell.
0: This switch is turned off. UEs processing HSPA
services are released after the HSPA function is
deactivated in the cell.
19)OMIT_UE_CAP_ENQ_RELOC_DCH_SWITCH
Whether the RNC sends a UE CAPABILITY
ENQUIRY message to a UE in the CELL_DCH state
during an incoming relocation procedure.
1: This switch is turned on. Under this circumstance,
the RNC does not send a UE CAPABILITY
ENQUIRY message to a UE in the CELL_DCH state
during an incoming relocation procedure.
0: This switch is turned off. Under this circumstance,
the RNC sends a UE CAPABILITY ENQUIRY
message to a UE in the CELL_DCH state in the
preceding scenario.
20)RAB_SETUP_CNT_CORRECT_SWITCH
Whether to measure the number of RAB setup
attempts when the cross processing of RAB setup and
cell update fails or the radio link reestablishment
triggered by RAB setup fails.
1: This switch is turned on. The number of RAB setup
attempts is measured.
0: This switch is turned off. The number of RAB setup
attempts is not measured.
21)FACH_DCCH_RRC_REL_NO_RSP_DELAY_US
E_URNTI
Whether to delay the assignment of the URNTI from
one UE to another when the timer for the UE to wait
for a response message from the RNC expires after the
UE in the CELL_FACH state sends an RRC
CONNECTION RELEASE message on the DCCH.
This switch prevents the assignment of the URNTI
from one UE to another to avoid URNTI conflicts.
This switch is turned on by default.
1: This switch is turned on. The RNC delays the
assignment of the URNTI from the current UE to
another UE.
0: This switch is turned off. The RNC immediately
assigns the URNTI from the current UE to another
UE.
22)FACH_CCCH_RRC_REL_NO_RSP_DELAY_US
E_URNTI
Whether to delay the assignment of the URNTI from
one UE to another when the timer for the UE to wait
for a response message from the RNC expires after the
UE in the CELL_FACH state sends an RRC
CONNECTION RELEASE message on the CCCH.
This switch prevents the assignment of the URNTI
from one UE to another to avoid URNTI conflicts.
This switch is turned off by default.
1: This switch is turned on. The RNC delays the
assignment of the URNTI from the current UE to
another UE.
0: This switch is turned off. The RNC immediately
assigns the URNTI from the current UE to another
UE.
23)RB_SETUP_RLC_INFO_OPT_SWITCH
Whether the RNC sets the "RLC info" IE of the "RB
information to setup" IE contained in the second and
third RB sub-flows to "Same as RB:0xM" if the RLC
SEND_UE_CAP_ENQ_RELOC_CCH_SWITCH,
REL_IUR_CCH_BEFORE_DSCR_SWITCH,
RELOC_CIPHER_PENDING_COMPATI_SWITCH,
COUNT_SPECIAL_RAB_ATT_SWITCH,
COUNT_STATE_CHG_BY_RAB_SWITCH,
DELAY_SEND_MEACTRL_SWITCH,
TAKE_ACTIVE_TIME_DRD_SWITCH,
CS_DISCONNECT_OPT_SWITCH,
NON_DCCC_RBRECFG_RL_REEST_SWITCH,
SMC_RL_REEST_SWITCH,
PSHO_CSFB_UE_CAP_ENQ_DELAY_SWITCH,
PAGING_OM_OPTIMIZE_SWITCH,
DEACTIVE_CELLHSPA_H2F_SWITCH,
OMIT_UE_CAP_ENQ_RELOC_DCH_SWITCH,
RAB_SETUP_CNT_CORRECT_SWITCH,
FACH_DCCH_RRC_REL_NO_RSP_DELAY_USE_
URNTI,
FACH_CCCH_RRC_REL_NO_RSP_DELAY_USE_
URNTI, RB_SETUP_RLC_INFO_OPT_SWITCH,
DCH_DISCARD_CELL_RESEL_CU_MSG_SWITC
H,
SYS_INIT_SPU_STATE_BROADCAST_OPT_SWI
TCH,
RB_RECFG_F2D_ISR_IC_FAIL_RRC_REL_SWIT
CH,
PTT_RAB_SETUP_ATT_CNT_CORRECT_SWITC
H,
P2D_DRD_FAIL_BACK_RESEL_CELL_SWITCH,
TRB_RST_CU_NOT_REEST_UM_RLC_TRB_SWI
TCH,
ONE_CNNODE_SCCP_CONG_SEL_OTHER_SWI
TCH, CSFB_UE_DELAY_RAU_SWITCH,
CSFB_UE_CS_IMEI_QUERY_DISABLE_SWITCH
Unit: None
Actual Value Range:
CONVERT_RELOC_FAIL_CAUSE_SWITCH,
DEAL_SRNS_CONTEXT_REQ_FIRST_SWITCH,
DELAY_DRNC_CODE_REL_SWITCH,
ROUT_IDT_BY_ROUTING_PARA_SWITCH,
COUNT_CS_REC_IU_REL_CMD_SWITCH,
SEND_UE_CAP_ENQ_RELOC_CCH_SWITCH,
REL_IUR_CCH_BEFORE_DSCR_SWITCH,
RELOC_CIPHER_PENDING_COMPATI_SWITCH,
COUNT_SPECIAL_RAB_ATT_SWITCH,
COUNT_STATE_CHG_BY_RAB_SWITCH,
DELAY_SEND_MEACTRL_SWITCH,
TAKE_ACTIVE_TIME_DRD_SWITCH,
CS_DISCONNECT_OPT_SWITCH,
NON_DCCC_RBRECFG_RL_REEST_SWITCH,
SMC_RL_REEST_SWITCH,
PSHO_CSFB_UE_CAP_ENQ_DELAY_SWITCH,
PAGING_OM_OPTIMIZE_SWITCH,
DEACTIVE_CELLHSPA_H2F_SWITCH,
OMIT_UE_CAP_ENQ_RELOC_DCH_SWITCH,
RAB_SETUP_CNT_CORRECT_SWITCH,
FACH_DCCH_RRC_REL_NO_RSP_DELAY_USE_
URNTI,
FACH_CCCH_RRC_REL_NO_RSP_DELAY_USE_
URNTI,
RB_SETUP_RLC_INFO_OPT_SWITCH,
DCH_DISCARD_CELL_RESEL_CU_MSG_SWITC
H,
SYS_INIT_SPU_STATE_BROADCAST_OPT_SWI
TCH,
RB_RECFG_F2D_ISR_IC_FAIL_RRC_REL_SWIT
CH,
PTT_RAB_SETUP_ATT_CNT_CORRECT_SWITC
H,
P2D_DRD_FAIL_BACK_RESEL_CELL_SWITCH,
TRB_RST_CU_NOT_REEST_UM_RLC_TRB_SWI
TCH,
ONE_CNNODE_SCCP_CONG_SEL_OTHER_SWI
TCH,
CSFB_UE_DELAY_RAU_SWITCH,
CSFB_UE_CS_IMEI_QUERY_DISABLE_SWITCH
Default Value:
CONVERT_RELOC_FAIL_CAUSE_SWITCH:
0,DEAL_SRNS_CONTEXT_REQ_FIRST_SWITCH:
0,DELAY_DRNC_CODE_REL_SWITCH:
0,ROUT_IDT_BY_ROUTING_PARA_SWITCH:
0,COUNT_CS_REC_IU_REL_CMD_SWITCH:
0,SEND_UE_CAP_ENQ_RELOC_CCH_SWITCH:
0,REL_IUR_CCH_BEFORE_DSCR_SWITCH:
0,RELOC_CIPHER_PENDING_COMPATI_SWITC
H:0,COUNT_SPECIAL_RAB_ATT_SWITCH:
0 ,COUNT_STATE_CHG_BY_RAB_SWITCH:
0 ,DELAY_SEND_MEACTRL_SWITCH:
RbSetup BSC690 SET WRFD- 3GPP Meaning: A timer to RNC wait for the RB setup
RspTmr 0 USTAT 010101 R9 response message from the UE when an RB setup
ETIME WRFD- Specific message is sent in AM.
R 140103 ations GUI Value Range: 300~300000
Call Unit: ms
Reestabl
ishment Actual Value Range: 300~300000
Default Value: 5000
RbSetup BSC691 SET WRFD- 3GPP Meaning: A timer to RNC wait for the RB setup
RspTmr 0 USTAT 010101 R9 response message from the UE when an RB setup
ETIME WRFD- Specific message is sent in AM.
R 140103 ations GUI Value Range: 300~300000
Call Unit: ms
Reestabl
ishment Actual Value Range: 300~300000
Default Value: 5000
RrcSecrt BSC690 SET WRFD- 3GPP Meaning: A timer to RNC wait for the response to
ModeC 0 USTAT 010101 R9 security mode command from UE in security mode
mpTmr ETIME Specific procedure.
R ations GUI Value Range: 100~10000
Unit: ms
Actual Value Range: 100~10000
Default Value: 5000
RrcSecrt BSC691 SET WRFD- 3GPP Meaning: A timer to RNC wait for the response to
ModeC 0 USTAT 010101 R9 security mode command from UE in security mode
mpTmr ETIME Specific procedure.
R ations GUI Value Range: 100~10000
Unit: ms
Actual Value Range: 100~10000
Default Value: 5000
18)L2U_SRVCC_PS_TIMEOUT_CS_RELOC_IN_S
WITCH
Whether to support the incoming CS handover during
the single radio voice call continuity (SRVCC) with
simultaneous CS and PS handovers if the PS
RELOCATION REQUEST message times out.
1: When this switch is set to on, the RNC supports the
incoming CS handover after receiving a
RELOCATION REQUEST message from the CS
domain during the SRVCC for CS+PS combined
services, if the RNC does not receive a
RELOCATION REQUEST message from the PS
domain within the period of time specified by
"IRatHoWaitPSRelocReqTmr" parameter in the "SET
USTATETIMER" command.
0: When this switch is set to off, the RNC does not
support the incoming CS handover in the preceding
scenario.
For details, see 3GPP TS 23.216.
19)CRYSTAL_VOICE_DEEPCOVER_SWITCH
Whether the RNC-level Crystal Voice in Deep
Coverage function takes effect.
1: This switch is set to on. The RNC-level Crystal
Voice in Deep Coverage function takes effect.
0: This switch is set to off. The RNC-level Crystal
Voice in Deep Coverage function does not take effect.
20)LOAD_BASED_P2D_SWITCH
Whether the load- and Ec/N0-based P2D state
transition algorithm is enabled.
1: Indicates that this switch is set to ON. If both of the
following conditions are met, the RNC triggers a P2D
state transition. If either of the following conditions is
not met, the RNC triggers a P2F state transition.
(1)The actual uplink cell load enters the state specified
by "ActualloadStateForP2D" or enters a lighter state,
and the downlink non-HSPA transmit power enters the
state specified by "NonHLoadStateForP2D" or enters
a lighter state. The values of the "ActualloadState-
ForP2D" and "NonHLoadStateForP2D" parameters
can be queried by running the RNC MML command
"LST UUESTATETRANS".
(2) The Ec/N0 is greater than or equal to
"P2DEcNoThd". The value of the "P2DEcNoThd"
parameter can be queried by running the RNC MML
command "LST UFRC".
TCH, CRYSTAL_VOICE_DEEPCOVER_SWITCH,
LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SWITCH,
STATE_FACH_CONSISTENT_OPTI_SWITCH,
D2P_RECFG_REEST_SWITCH,
IMPVD_UL_COVER_FOR_SRB_OVER_DCH_SW
ITCH, UL_DT_SAI_PLMN_CMP_SWITCH,
RRC_CONN_SETUP_MSG_ENH_OPT_SWITCH,
UE_UDA_CAP_QUERY_SWITCH, UDA_SWITCH
Unit: None
Actual Value Range:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWI
TCH,
INTERRAT_LOAD_REPORT_FROM_LTE_SWITC
H,
UL_EVQI_SWITCH,
DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH,
APP_GRP_RES_RSV_SWITCH,
RIM_ON_ECO_SWITCH,
PRIMOPER_NONROAM_USER_CN_SA_SWITCH
,
SRBCHG_DRD_FAST_RB_SETUP_SWITCH,
SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH,
FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH
,
WBAMR_HHO_FAIL_ROLLBACK_SWITCH,
EXTD_LAC_PAGING_SWITCH,
TCP_PROXY_SWITCH,
SEAMLESS_CRYSTAL_VOICE_SWITCH,
CS_RB_PRI_MC_SWITCH,
L2U_SRVCC_PS_TIMEOUT_CS_RELOC_IN_SWI
TCH,
CRYSTAL_VOICE_DEEPCOVER_SWITCH,
LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SWITCH,
STATE_FACH_CONSISTENT_OPTI_SWITCH,
D2P_RECFG_REEST_SWITCH,
IMPVD_UL_COVER_FOR_SRB_OVER_DCH_SW
ITCH,
UL_DT_SAI_PLMN_CMP_SWITCH,
RRC_CONN_SETUP_MSG_ENH_OPT_SWITCH,
UE_UDA_CAP_QUERY_SWITCH,
UDA_SWITCH
Default Value:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWI
TCH:
0,INTERRAT_LOAD_REPORT_FROM_LTE_SWIT
CH:0,UL_EVQI_SWITCH:0,DL_EVQI_SWITCH:
0,VIDEO_RATE_ADAPTION_SWITCH:
0,VOIP_MANAGE_SWITCH:
0,DIFF_SERVICE_ON_TERMINAL_SWITCH:
0,APP_GRP_RES_RSV_SWITCH:
0,RIM_ON_ECO_SWITCH:
0,PRIMOPER_NONROAM_USER_CN_SA_SWITC
H:0,SRBCHG_DRD_FAST_RB_SETUP_SWITCH:
0,SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH:
0,FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITC
H:0,WBAMR_HHO_FAIL_ROLLBACK_SWITCH:
0,EXTD_LAC_PAGING_SWITCH:
0,TCP_PROXY_SWITCH:
0,SEAMLESS_CRYSTAL_VOICE_SWITCH:
0,CS_RB_PRI_MC_SWITCH:
0,L2U_SRVCC_PS_TIMEOUT_CS_RELOC_IN_S
WITCH:
0,CRYSTAL_VOICE_DEEPCOVER_SWITCH:
0,LOAD_BASED_P2D_SWITCH:
0,PS_R99_BLER_STAT_OPT_SWITCH:
0,STATE_FACH_CONSISTENT_OPTI_SWITCH:
0,D2P_RECFG_REEST_SWITCH:
0,IMPVD_UL_COVER_FOR_SRB_OVER_DCH_S
WITCH:0,UL_DT_SAI_PLMN_CMP_SWITCH:
0,RRC_CONN_SETUP_MSG_ENH_OPT_SWITCH:
0,UE_UDA_CAP_QUERY_SWITCH:
0,UDA_SWITCH:0
18)L2U_SRVCC_PS_TIMEOUT_CS_RELOC_IN_S
WITCH
Whether to support the incoming CS handover during
the single radio voice call continuity (SRVCC) with
simultaneous CS and PS handovers if the PS
RELOCATION REQUEST message times out.
1: When this switch is set to on, the RNC supports the
incoming CS handover after receiving a
RELOCATION REQUEST message from the CS
domain during the SRVCC for CS+PS combined
services, if the RNC does not receive a
RELOCATION REQUEST message from the PS
domain within the period of time specified by
"IRatHoWaitPSRelocReqTmr" parameter in the "SET
USTATETIMER" command.
0: When this switch is set to off, the RNC does not
support the incoming CS handover in the preceding
scenario.
For details, see 3GPP TS 23.216.
19)CRYSTAL_VOICE_DEEPCOVER_SWITCH
Whether the RNC-level Crystal Voice in Deep
Coverage function takes effect.
1: This switch is set to on. The RNC-level Crystal
Voice in Deep Coverage function takes effect.
0: This switch is set to off. The RNC-level Crystal
Voice in Deep Coverage function does not take effect.
20)LOAD_BASED_P2D_SWITCH
Whether the load- and Ec/N0-based P2D state
transition algorithm is enabled.
1: Indicates that this switch is set to ON. If both of the
following conditions are met, the RNC triggers a P2D
state transition. If either of the following conditions is
not met, the RNC triggers a P2F state transition.
(1)The actual uplink cell load enters the state specified
by "ActualloadStateForP2D" or enters a lighter state,
and the downlink non-HSPA transmit power enters the
state specified by "NonHLoadStateForP2D" or enters
a lighter state. The values of the "ActualloadState-
ForP2D" and "NonHLoadStateForP2D" parameters
can be queried by running the RNC MML command
"LST UUESTATETRANS".
(2) The Ec/N0 is greater than or equal to
"P2DEcNoThd". The value of the "P2DEcNoThd"
parameter can be queried by running the RNC MML
command "LST UFRC".
TCH, CRYSTAL_VOICE_DEEPCOVER_SWITCH,
LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SWITCH,
STATE_FACH_CONSISTENT_OPTI_SWITCH,
D2P_RECFG_REEST_SWITCH,
IMPVD_UL_COVER_FOR_SRB_OVER_DCH_SW
ITCH, UL_DT_SAI_PLMN_CMP_SWITCH,
RRC_CONN_SETUP_MSG_ENH_OPT_SWITCH,
UE_UDA_CAP_QUERY_SWITCH, UDA_SWITCH
Unit: None
Actual Value Range:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWI
TCH,
INTERRAT_LOAD_REPORT_FROM_LTE_SWITC
H,
UL_EVQI_SWITCH,
DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH,
APP_GRP_RES_RSV_SWITCH,
RIM_ON_ECO_SWITCH,
PRIMOPER_NONROAM_USER_CN_SA_SWITCH
,
SRBCHG_DRD_FAST_RB_SETUP_SWITCH,
SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH,
FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH
,
WBAMR_HHO_FAIL_ROLLBACK_SWITCH,
EXTD_LAC_PAGING_SWITCH,
TCP_PROXY_SWITCH,
SEAMLESS_CRYSTAL_VOICE_SWITCH,
CS_RB_PRI_MC_SWITCH,
L2U_SRVCC_PS_TIMEOUT_CS_RELOC_IN_SWI
TCH,
CRYSTAL_VOICE_DEEPCOVER_SWITCH,
LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SWITCH,
STATE_FACH_CONSISTENT_OPTI_SWITCH,
D2P_RECFG_REEST_SWITCH,
IMPVD_UL_COVER_FOR_SRB_OVER_DCH_SW
ITCH,
UL_DT_SAI_PLMN_CMP_SWITCH,
RRC_CONN_SETUP_MSG_ENH_OPT_SWITCH,
UE_UDA_CAP_QUERY_SWITCH,
UDA_SWITCH
Default Value:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWI
TCH:
0,INTERRAT_LOAD_REPORT_FROM_LTE_SWIT
CH:0,UL_EVQI_SWITCH:0,DL_EVQI_SWITCH:
0,VIDEO_RATE_ADAPTION_SWITCH:
0,VOIP_MANAGE_SWITCH:
0,DIFF_SERVICE_ON_TERMINAL_SWITCH:
0,APP_GRP_RES_RSV_SWITCH:
0,RIM_ON_ECO_SWITCH:
0,PRIMOPER_NONROAM_USER_CN_SA_SWITC
H:0,SRBCHG_DRD_FAST_RB_SETUP_SWITCH:
0,SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH:
0,FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITC
H:0,WBAMR_HHO_FAIL_ROLLBACK_SWITCH:
0,EXTD_LAC_PAGING_SWITCH:
0,TCP_PROXY_SWITCH:
0,SEAMLESS_CRYSTAL_VOICE_SWITCH:
0,CS_RB_PRI_MC_SWITCH:
0,L2U_SRVCC_PS_TIMEOUT_CS_RELOC_IN_S
WITCH:
0,CRYSTAL_VOICE_DEEPCOVER_SWITCH:
0,LOAD_BASED_P2D_SWITCH:
0,PS_R99_BLER_STAT_OPT_SWITCH:
0,STATE_FACH_CONSISTENT_OPTI_SWITCH:
0,D2P_RECFG_REEST_SWITCH:
0,IMPVD_UL_COVER_FOR_SRB_OVER_DCH_S
WITCH:0,UL_DT_SAI_PLMN_CMP_SWITCH:
0,RRC_CONN_SETUP_MSG_ENH_OPT_SWITCH:
0,UE_UDA_CAP_QUERY_SWITCH:
0,UDA_SWITCH:0
D2PRlR BSC690 SET None None Meaning: Timer set to wait for the restoration of the
strTmr 0 USTAT only RL in an active set during a D2P reconfiguration
ETIME and reestablishment procedure after the RL becomes
R out-of-synchronization. It is recommended that this
parameter be set to a value less than or equal to that of
the RlRstrTmr parameter.
GUI Value Range: 1~300
Unit: s
Actual Value Range: 1~300
Default Value: 11
D2PRlR BSC691 SET None None Meaning: Timer set to wait for the restoration of the
strTmr 0 USTAT only RL in an active set during a D2P reconfiguration
ETIME and reestablishment procedure after the RL becomes
R out-of-synchronization. It is recommended that this
parameter be set to a value less than or equal to that of
the RlRstrTmr parameter.
GUI Value Range: 1~300
Unit: s
Actual Value Range: 1~300
Default Value: 11
13)EFACH_RRC_REG_CMP_SWITCH(E-FACH
RRC Registration Compatibility Switch)
Whether special UEs use the E-FACH to carry their
RRC CONNECTION SETUP messages when the cell
is enabled with E-FACH.
1: This switch is set to on. the RNC retransmits the
last RRC CONNECTION SETUP message on the E-
FACH if special users do not respond to the RRC
CONNECTION SETUP message on the FACH. If the
UE returns an RRC CONNECTION SETUP CMP
message, the UE stays in the CELL_DCH state during
data transmission.
0: This switch is set to off. no special processing is
performed on special users.
14)
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH
(Discard Responses with Incorrect TRANSCIDs from
UEs During P2D)
Whether the RNC discards a RADIO BEARER
RECONFIGURATION COMPLETE message
received from a UE during P2D state transitions when
the value of the "RRC transaction identifier" IE in the
message is incorrect.
1: This switch is set to on. The RNC discards the
message and waits for the UE's response.
0: This switch is set to off. The RNC rolls back the
P2D state transition procedure.
15)
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWIT
CH (HHO Rollback Switch for 12.2K AMR Services
with AMRC Enabled)
Whether the RNC performs rollback after 12.2 kbit/s
AMR-NB services experience hard handover failures
in the scenario where the narrowband AMRC function
takes effect.
0: This switch is set to off. The RNC does not perform
rollback after 12.2 kbit/s AMR-NB services
experience hard handover failures in the preceding
scenario.
1: This switch is set to on. The RNC performs
rollback after 12.2 kbit/s AMR-NB services
experience hard handover failures in the preceding
scenario.
16)RELOC_IN_RG_COMB_INDEX_ALLOC_SWIT
CH
29)INTERRAT2U_INTEG_PROTECT_OPT_SWITC
H(Integrity Protection Optimization Switch for
Incoming Inter-RAT Handovers)
Whether the optimized integrity protection function is
enabled for incoming L2U or G2U inter-RAT
handovers.
1: This switch is set to on. The integrity protection
function is immediately activated for SRB0 to SRB4
after the incoming L2U or G2U inter-RAT handover is
complete.
0: This switch is set to off. The integrity protection
function is activated only for SRB2 after the incoming
L2U or G2U inter-RAT handover is complete. The
integrity protection for other SRBs (SRB0, SRB1,
SRB3, and SRB4) is activated only after the UE sends
a message.
30)CS_PAGING_OVERLAP_RRC_OPT_SWITCH(
Optimize CS Paging During RRC Procedures)
Whether the UE will be paged again when an TMSI-
based CS paging procedure occurs in parallel with an
RRC connection setup procedure.
1: Indicates that this switch is set to ON. If the TMSI-
based CS paging procedure fails, the UE will be paged
again.
0: Indicates that this switch is set to OFF. If the TMSI-
based CS paging procedure fails, the UE will not be
paged again.
31)INTRA_NODEB_RLCC_INIT_CAP_OPT_SWIT
CH(Optimize the Rate upon NodeB RL Change for H
Services)
Whether the rate optimization policy is applied in the
scenario where the radio link (RL) for HSPA services
changes inside the NodeB.
1: This switch is set to on. The rate optimization
policy is applied in the scenario where the RL for
HSPA services changes inside the NodeB.
0: This switch is set to off. The rate optimization
policy is not applied in the scenario where the RL for
HSPA services changes inside the NodeB.
32)DRNC_RL_PARA_UPT_OPT_SWITCH(RL
Parameter Update Optimization Switch on RNC)
Whether the RL PARA UPT IND message over the
Iur interface can be correctly processed.
DRNC_RL_REEST_OPT_SWITCH,
URA2FACH_OVERLAP_CELLUPT_PROC_SWIT
CH,
RB_SETUP_F2D_USE_AM_RLC_SWITCH,
RB_RECFG_D2F_USE_AM_RLC_SWITCH,
RB_RECFG_F2D_USE_AM_RLC_SWITCH,
RRC_UE_USER_SMOOTH_OPT_SWITCH,
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SWITCH,
CPC_OPT_FOR_RLSETUP_SWITCH,
D2P_L2DEACT_FAIL_OPT_SWITCH,
EFACH_RRC_REG_CMP_SWITCH,
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH,
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWIT
CH,
RELOC_IN_RG_COMB_INDEX_ALLOC_SWITC
H,
SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITCH,
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SWITCH,
ASYN_RL_REEST_OPT_SWITCH,
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWIT
CH,
URA_PCH_LAC_RAC_CHG_NO_PAGING_SWIT
CH,
PAGING_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_USE_CS_KEY_SWITCH,
SOCKET_RECEIVE_DATA_CORRECT_SWITCH,
CU_PRI_OVERLAP_OTHER_PROC_SWITCH,
INTERRAT2U_INTEG_PROTECT_OPT_SWITCH,
CS_PAGING_OVERLAP_RRC_OPT_SWITCH,
INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH
,
DRNC_RL_PARA_UPT_OPT_SWITCH
Default Value:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH:
0,RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_
SWITCH:0,DRNC_RL_REEST_OPT_SWITCH:
1,URA2FACH_OVERLAP_CELLUPT_PROC_SWI
TCH:0,RB_SETUP_F2D_USE_AM_RLC_SWITCH:
0,RB_RECFG_D2F_USE_AM_RLC_SWITCH:
0,RB_RECFG_F2D_USE_AM_RLC_SWITCH:
0,RRC_UE_USER_SMOOTH_OPT_SWITCH:
1,TRNC_LOAD_CTRL_SWITCH:
0,IU_SIG_REL_PCH_PAGING_SWITCH:
0,CPC_OPT_FOR_RLSETUP_SWITCH:
1,D2P_L2DEACT_FAIL_OPT_SWITCH:
0,EFACH_RRC_REG_CMP_SWITCH:
0,P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITC
H:
0,AMRC_ON_122_AMR_HHO_ROLL_BACK_SWI
TCH:
0,RELOC_IN_RG_COMB_INDEX_ALLOC_SWIT
CH:0,SCM_CU_CROSS_SWITCH:
0,DRNC_HSPA_CM_OPT_SWITCH:
0,IUB_TRANSID_OPT_SWITCH:
0,L2_ENHENCE_RECFG_OPT_SWITCH:
0,ASYN_RL_REEST_OPT_SWITCH:
0,RNC_IMSI_HO_OPT_SWITCH:
0,IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWI
TCH:
0,URA_PCH_LAC_RAC_CHG_NO_PAGING_SWI
TCH:0,PAGING_OVERLAP_CU_OPT_SWITCH:
0,SRVCC_RELOC_IN_USE_CS_KEY_SWITCH:
1,SOCKET_RECEIVE_DATA_CORRECT_SWITCH
:1,CU_PRI_OVERLAP_OTHER_PROC_SWITCH:
0,INTERRAT2U_INTEG_PROTECT_OPT_SWITC
H:0,CS_PAGING_OVERLAP_RRC_OPT_SWITCH:
0,INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITC
H:0,DRNC_RL_PARA_UPT_OPT_SWITCH:1
13)EFACH_RRC_REG_CMP_SWITCH(E-FACH
RRC Registration Compatibility Switch)
Whether special UEs use the E-FACH to carry their
RRC CONNECTION SETUP messages when the cell
is enabled with E-FACH.
1: This switch is set to on. the RNC retransmits the
last RRC CONNECTION SETUP message on the E-
FACH if special users do not respond to the RRC
CONNECTION SETUP message on the FACH. If the
UE returns an RRC CONNECTION SETUP CMP
message, the UE stays in the CELL_DCH state during
data transmission.
0: This switch is set to off. no special processing is
performed on special users.
14)
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH
(Discard Responses with Incorrect TRANSCIDs from
UEs During P2D)
Whether the RNC discards a RADIO BEARER
RECONFIGURATION COMPLETE message
received from a UE during P2D state transitions when
the value of the "RRC transaction identifier" IE in the
message is incorrect.
1: This switch is set to on. The RNC discards the
message and waits for the UE's response.
0: This switch is set to off. The RNC rolls back the
P2D state transition procedure.
15)
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWIT
CH (HHO Rollback Switch for 12.2K AMR Services
with AMRC Enabled)
Whether the RNC performs rollback after 12.2 kbit/s
AMR-NB services experience hard handover failures
in the scenario where the narrowband AMRC function
takes effect.
0: This switch is set to off. The RNC does not perform
rollback after 12.2 kbit/s AMR-NB services
experience hard handover failures in the preceding
scenario.
1: This switch is set to on. The RNC performs
rollback after 12.2 kbit/s AMR-NB services
experience hard handover failures in the preceding
scenario.
16)RELOC_IN_RG_COMB_INDEX_ALLOC_SWIT
CH
29)INTERRAT2U_INTEG_PROTECT_OPT_SWITC
H(Integrity Protection Optimization Switch for
Incoming Inter-RAT Handovers)
Whether the optimized integrity protection function is
enabled for incoming L2U or G2U inter-RAT
handovers.
1: This switch is set to on. The integrity protection
function is immediately activated for SRB0 to SRB4
after the incoming L2U or G2U inter-RAT handover is
complete.
0: This switch is set to off. The integrity protection
function is activated only for SRB2 after the incoming
L2U or G2U inter-RAT handover is complete. The
integrity protection for other SRBs (SRB0, SRB1,
SRB3, and SRB4) is activated only after the UE sends
a message.
30)CS_PAGING_OVERLAP_RRC_OPT_SWITCH(
Optimize CS Paging During RRC Procedures)
Whether the UE will be paged again when an TMSI-
based CS paging procedure occurs in parallel with an
RRC connection setup procedure.
1: Indicates that this switch is set to ON. If the TMSI-
based CS paging procedure fails, the UE will be paged
again.
0: Indicates that this switch is set to OFF. If the TMSI-
based CS paging procedure fails, the UE will not be
paged again.
31)INTRA_NODEB_RLCC_INIT_CAP_OPT_SWIT
CH(Optimize the Rate upon NodeB RL Change for H
Services)
Whether the rate optimization policy is applied in the
scenario where the radio link (RL) for HSPA services
changes inside the NodeB.
1: This switch is set to on. The rate optimization
policy is applied in the scenario where the RL for
HSPA services changes inside the NodeB.
0: This switch is set to off. The rate optimization
policy is not applied in the scenario where the RL for
HSPA services changes inside the NodeB.
32)DRNC_RL_PARA_UPT_OPT_SWITCH(RL
Parameter Update Optimization Switch on RNC)
Whether the RL PARA UPT IND message over the
Iur interface can be correctly processed.
DRNC_RL_REEST_OPT_SWITCH,
URA2FACH_OVERLAP_CELLUPT_PROC_SWIT
CH,
RB_SETUP_F2D_USE_AM_RLC_SWITCH,
RB_RECFG_D2F_USE_AM_RLC_SWITCH,
RB_RECFG_F2D_USE_AM_RLC_SWITCH,
RRC_UE_USER_SMOOTH_OPT_SWITCH,
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SWITCH,
CPC_OPT_FOR_RLSETUP_SWITCH,
D2P_L2DEACT_FAIL_OPT_SWITCH,
EFACH_RRC_REG_CMP_SWITCH,
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH,
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWIT
CH,
RELOC_IN_RG_COMB_INDEX_ALLOC_SWITC
H,
SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITCH,
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SWITCH,
ASYN_RL_REEST_OPT_SWITCH,
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWIT
CH,
URA_PCH_LAC_RAC_CHG_NO_PAGING_SWIT
CH,
PAGING_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_USE_CS_KEY_SWITCH,
SOCKET_RECEIVE_DATA_CORRECT_SWITCH,
CU_PRI_OVERLAP_OTHER_PROC_SWITCH,
INTERRAT2U_INTEG_PROTECT_OPT_SWITCH,
CS_PAGING_OVERLAP_RRC_OPT_SWITCH,
INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH
,
DRNC_RL_PARA_UPT_OPT_SWITCH
Default Value:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH:
0,RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_
SWITCH:0,DRNC_RL_REEST_OPT_SWITCH:
1,URA2FACH_OVERLAP_CELLUPT_PROC_SWI
TCH:0,RB_SETUP_F2D_USE_AM_RLC_SWITCH:
0,RB_RECFG_D2F_USE_AM_RLC_SWITCH:
0,RB_RECFG_F2D_USE_AM_RLC_SWITCH:
0,RRC_UE_USER_SMOOTH_OPT_SWITCH:
1,TRNC_LOAD_CTRL_SWITCH:
0,IU_SIG_REL_PCH_PAGING_SWITCH:
0,CPC_OPT_FOR_RLSETUP_SWITCH:
1,D2P_L2DEACT_FAIL_OPT_SWITCH:
0,EFACH_RRC_REG_CMP_SWITCH:
0,P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITC
H:
0,AMRC_ON_122_AMR_HHO_ROLL_BACK_SWI
TCH:
0,RELOC_IN_RG_COMB_INDEX_ALLOC_SWIT
CH:0,SCM_CU_CROSS_SWITCH:
0,DRNC_HSPA_CM_OPT_SWITCH:
0,IUB_TRANSID_OPT_SWITCH:
0,L2_ENHENCE_RECFG_OPT_SWITCH:
0,ASYN_RL_REEST_OPT_SWITCH:
0,RNC_IMSI_HO_OPT_SWITCH:
0,IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWI
TCH:
0,URA_PCH_LAC_RAC_CHG_NO_PAGING_SWI
TCH:0,PAGING_OVERLAP_CU_OPT_SWITCH:
0,SRVCC_RELOC_IN_USE_CS_KEY_SWITCH:
1,SOCKET_RECEIVE_DATA_CORRECT_SWITCH
:1,CU_PRI_OVERLAP_OTHER_PROC_SWITCH:
0,INTERRAT2U_INTEG_PROTECT_OPT_SWITC
H:0,CS_PAGING_OVERLAP_RRC_OPT_SWITCH:
0,INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITC
H:0,DRNC_RL_PARA_UPT_OPT_SWITCH:1
6)SPECUSER_PCH_FACH2EFACH_DISABLED_S
WITCH(Forbid Special UEs in the PCH State to
Perform FACH2EFACH Cell Updates)
Whether a specified UE is forbidden to perform the
P2P procedure.
1: This switch is turned on. If a specified UE moves
from a FACH cell to a cell with the Uplink or
Downlink Enhanced CELL_FACH feature activated,
or from a cell with the Uplink Enhanced
CELL_FACH feature activated to a cell with the
Downlink Enhanced CELL_FACH feature activated,
the UE is forbidden to perform the P2P procedure and
its state is reconfigured as CELL-FACH.
0: This switch is turned off. If a specified UE moves
from a FACH cell to a cell with the Uplink or
Downlink Enhanced CELL_FACH feature activated,
or from a cell with the Uplink Enhanced
CELL_FACH feature activated to a cell with the
Downlink Enhanced CELL_FACH feature activated,
the UE is allowed to perform the P2P procedure.
7)SPECUSER_INHIBIT_D2P_SWITCH(D2P
Procedure Inhibition Switch)
Whether to disable the D2P state transition for special
UEs.
When this switch is set to on, special UEs perform the
D2F state transition, not the D2P state transition if
they do not have data transmission for the period of
time specified by "D2PPsInactTimer" in the "SET
UUESTATETRANSTIMER" command.
When this switch is set to off, special UEs perform the
D2P state transition if they do not have data
transmission for the period of time specified by
"D2PPsInactTimer" in the "SET
UUESTATETRANSTIMER" command.
8)H_SERV_CELL_CHG_MSG_OPT_DISABLED_S
WITCH(Disable H Serving Cell Change MSG Size
Reduction)
Whether to disable the size reduction of the HSDPA
serving cell change message for specified UEs.
1: This switch is set to on. The size of the HSDPA
serving cell change message cannot be reduced for
specified UEs. The original HSDPA serving cell
change procedure is used.
SPECUSER_SRB_OVER_HSDPA_DISABLED_SW
ITCH,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITC
H, SPECUSER_EFACH_DISABLED_SWITCH,
SPECUSER_ERACH_DISABLED_SWITCH,
SPECUSER_PCH_FACH2EFACH_DISABLED_SW
ITCH, SPECUSER_INHIBIT_D2P_SWITCH,
H_SERV_CELL_CHG_MSG_OPT_DISABLED_SW
ITCH,
EFACH_ERACH_UE_D2P_DISABLED_SWITCH,
SPECUSER_DL_BLER_MEAS_DISABLED_SWIT
CH,
SPECUSER_AGPS_MEAS_DISABLED_SWITCH,
SPECUSER_UE_TX_PWR_MEAS_DISABLED_S
WITCH,
SPECUSER_CELLID_RTT_MEAS_DISABLED_S
WITCH,
FAST_H_SERV_CELL_CHANGE_DISABLED_SW
ITCH,
SPECUSER_SFDC_HSDPA_DISABLED_SWITCH,
SPECUSER_DF3C_HSDPA_DISABLED_SWITCH,
SPECUSER_FASTMULRLSETUP_DISABLED_SW
ITCH, SPECUSER_R6_EFACH_CMP_SWITCH,
SPECUSER_IFFASTMULRL_CMP_DISABLED_S
WITCH,
SPECUSER_AGPS_MEAS_ENABLED_SWITCH,
SPECUSER_ENABLE_RPRT_AGPR_MR_ONCE_S
WITCH,
SPECUSER_PS_SETUP_DCH0K_DISABLED_SWI
TCH,
SPECUSER_FACH_CONSIS_OPTI_DISABLE_SWI
TCH,
SPECUSER_ADJACENT_FREQ_DISABLED_SWI
TCH,
SPECUSER_RL_PERFORMANCE_OPT_SWITCH
Unit: None
Actual Value Range:
P2F_REDIR_DISABLED_SWITCH,
SPECUSER_SRB_OVER_HSDPA_DISABLED_SW
ITCH,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITC
H,
SPECUSER_EFACH_DISABLED_SWITCH,
SPECUSER_ERACH_DISABLED_SWITCH,
SPECUSER_PCH_FACH2EFACH_DISABLED_SW
ITCH,
SPECUSER_INHIBIT_D2P_SWITCH,
H_SERV_CELL_CHG_MSG_OPT_DISABLED_SW
ITCH,
EFACH_ERACH_UE_D2P_DISABLED_SWITCH,
SPECUSER_DL_BLER_MEAS_DISABLED_SWIT
CH,
SPECUSER_AGPS_MEAS_DISABLED_SWITCH,
SPECUSER_UE_TX_PWR_MEAS_DISABLED_S
WITCH,
SPECUSER_CELLID_RTT_MEAS_DISABLED_S
WITCH,
FAST_H_SERV_CELL_CHANGE_DISABLED_SW
ITCH,
SPECUSER_SFDC_HSDPA_DISABLED_SWITCH,
SPECUSER_DF3C_HSDPA_DISABLED_SWITCH,
SPECUSER_FASTMULRLSETUP_DISABLED_SW
ITCH,
SPECUSER_R6_EFACH_CMP_SWITCH,
SPECUSER_IFFASTMULRL_CMP_DISABLED_S
WITCH,
SPECUSER_AGPS_MEAS_ENABLED_SWITCH,
SPECUSER_ENABLE_RPRT_AGPR_MR_ONCE_S
WITCH,
SPECUSER_PS_SETUP_DCH0K_DISABLED_SWI
TCH,
SPECUSER_FACH_CONSIS_OPTI_DISABLE_SWI
TCH,
SPECUSER_ADJACENT_FREQ_DISABLED_SWI
TCH,
SPECUSER_RL_PERFORMANCE_OPT_SWITCH
Default Value: P2F_REDIR_DISABLED_SWITCH:
0,SPECUSER_SRB_OVER_HSDPA_DISABLED_S
WITCH:0,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITC
H:0, SPECUSER_EFACH_DISABLED_SWITCH:0,
SPECUSER_ERACH_DISABLED_SWITCH:
0,SPECUSER_PCH_FACH2EFACH_DISABLED_S
WITCH:0,SPECUSER_INHIBIT_D2P_SWITCH:
0,H_SERV_CELL_CHG_MSG_OPT_DISABLED_S
WITCH:
0,EFACH_ERACH_UE_D2P_DISABLED_SWITCH
:
0,SPECUSER_DL_BLER_MEAS_DISABLED_SWI
TCH:
0,SPECUSER_AGPS_MEAS_DISABLED_SWITCH
:
0,SPECUSER_UE_TX_PWR_MEAS_DISABLED_S
WITCH:
0,SPECUSER_CELLID_RTT_MEAS_DISABLED_S
WITCH:
0,FAST_H_SERV_CELL_CHANGE_DISABLED_S
WITCH:
0,SPECUSER_SFDC_HSDPA_DISABLED_SWITC
H:
0,SPECUSER_DF3C_HSDPA_DISABLED_SWITC
H:
0,SPECUSER_FASTMULRLSETUP_DISABLED_S
WITCH:0,SPECUSER_R6_EFACH_CMP_SWITCH:
0,SPECUSER_IFFASTMULRL_CMP_DISABLED_
SWITCH:
0,SPECUSER_AGPS_MEAS_ENABLED_SWITCH:
0,SPECUSER_ENABLE_RPRT_AGPR_MR_ONCE
_SWITCH:
0,SPECUSER_PS_SETUP_DCH0K_DISABLED_S
WITCH:
0,SPECUSER_FACH_CONSIS_OPTI_DISABLE_S
WITCH:
0,SPECUSER_ADJACENT_FREQ_DISABLED_SW
ITCH:
0,SPECUSER_RL_PERFORMANCE_OPT_SWITC
H:0
6)SPECUSER_PCH_FACH2EFACH_DISABLED_S
WITCH(Forbid Special UEs in the PCH State to
Perform FACH2EFACH Cell Updates)
Whether a specified UE is forbidden to perform the
P2P procedure.
1: This switch is turned on. If a specified UE moves
from a FACH cell to a cell with the Uplink or
Downlink Enhanced CELL_FACH feature activated,
or from a cell with the Uplink Enhanced
CELL_FACH feature activated to a cell with the
Downlink Enhanced CELL_FACH feature activated,
the UE is forbidden to perform the P2P procedure and
its state is reconfigured as CELL-FACH.
0: This switch is turned off. If a specified UE moves
from a FACH cell to a cell with the Uplink or
Downlink Enhanced CELL_FACH feature activated,
or from a cell with the Uplink Enhanced
CELL_FACH feature activated to a cell with the
Downlink Enhanced CELL_FACH feature activated,
the UE is allowed to perform the P2P procedure.
7)SPECUSER_INHIBIT_D2P_SWITCH(D2P
Procedure Inhibition Switch)
Whether to disable the D2P state transition for special
UEs.
When this switch is set to on, special UEs perform the
D2F state transition, not the D2P state transition if
they do not have data transmission for the period of
time specified by "D2PPsInactTimer" in the "SET
UUESTATETRANSTIMER" command.
When this switch is set to off, special UEs perform the
D2P state transition if they do not have data
transmission for the period of time specified by
"D2PPsInactTimer" in the "SET
UUESTATETRANSTIMER" command.
8)H_SERV_CELL_CHG_MSG_OPT_DISABLED_S
WITCH(Disable H Serving Cell Change MSG Size
Reduction)
Whether to disable the size reduction of the HSDPA
serving cell change message for specified UEs.
1: This switch is set to on. The size of the HSDPA
serving cell change message cannot be reduced for
specified UEs. The original HSDPA serving cell
change procedure is used.
SPECUSER_SRB_OVER_HSDPA_DISABLED_SW
ITCH,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITC
H, SPECUSER_EFACH_DISABLED_SWITCH,
SPECUSER_ERACH_DISABLED_SWITCH,
SPECUSER_PCH_FACH2EFACH_DISABLED_SW
ITCH, SPECUSER_INHIBIT_D2P_SWITCH,
H_SERV_CELL_CHG_MSG_OPT_DISABLED_SW
ITCH,
EFACH_ERACH_UE_D2P_DISABLED_SWITCH,
SPECUSER_DL_BLER_MEAS_DISABLED_SWIT
CH,
SPECUSER_AGPS_MEAS_DISABLED_SWITCH,
SPECUSER_UE_TX_PWR_MEAS_DISABLED_S
WITCH,
SPECUSER_CELLID_RTT_MEAS_DISABLED_S
WITCH,
FAST_H_SERV_CELL_CHANGE_DISABLED_SW
ITCH,
SPECUSER_SFDC_HSDPA_DISABLED_SWITCH,
SPECUSER_DF3C_HSDPA_DISABLED_SWITCH,
SPECUSER_FASTMULRLSETUP_DISABLED_SW
ITCH, SPECUSER_R6_EFACH_CMP_SWITCH,
SPECUSER_IFFASTMULRL_CMP_DISABLED_S
WITCH,
SPECUSER_AGPS_MEAS_ENABLED_SWITCH,
SPECUSER_ENABLE_RPRT_AGPR_MR_ONCE_S
WITCH,
SPECUSER_PS_SETUP_DCH0K_DISABLED_SWI
TCH,
SPECUSER_FACH_CONSIS_OPTI_DISABLE_SWI
TCH,
SPECUSER_ADJACENT_FREQ_DISABLED_SWI
TCH,
SPECUSER_RL_PERFORMANCE_OPT_SWITCH
Unit: None
Actual Value Range:
P2F_REDIR_DISABLED_SWITCH,
SPECUSER_SRB_OVER_HSDPA_DISABLED_SW
ITCH,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITC
H,
SPECUSER_EFACH_DISABLED_SWITCH,
SPECUSER_ERACH_DISABLED_SWITCH,
SPECUSER_PCH_FACH2EFACH_DISABLED_SW
ITCH,
SPECUSER_INHIBIT_D2P_SWITCH,
H_SERV_CELL_CHG_MSG_OPT_DISABLED_SW
ITCH,
EFACH_ERACH_UE_D2P_DISABLED_SWITCH,
SPECUSER_DL_BLER_MEAS_DISABLED_SWIT
CH,
SPECUSER_AGPS_MEAS_DISABLED_SWITCH,
SPECUSER_UE_TX_PWR_MEAS_DISABLED_S
WITCH,
SPECUSER_CELLID_RTT_MEAS_DISABLED_S
WITCH,
FAST_H_SERV_CELL_CHANGE_DISABLED_SW
ITCH,
SPECUSER_SFDC_HSDPA_DISABLED_SWITCH,
SPECUSER_DF3C_HSDPA_DISABLED_SWITCH,
SPECUSER_FASTMULRLSETUP_DISABLED_SW
ITCH,
SPECUSER_R6_EFACH_CMP_SWITCH,
SPECUSER_IFFASTMULRL_CMP_DISABLED_S
WITCH,
SPECUSER_AGPS_MEAS_ENABLED_SWITCH,
SPECUSER_ENABLE_RPRT_AGPR_MR_ONCE_S
WITCH,
SPECUSER_PS_SETUP_DCH0K_DISABLED_SWI
TCH,
SPECUSER_FACH_CONSIS_OPTI_DISABLE_SWI
TCH,
SPECUSER_ADJACENT_FREQ_DISABLED_SWI
TCH,
SPECUSER_RL_PERFORMANCE_OPT_SWITCH
Default Value: P2F_REDIR_DISABLED_SWITCH:
0,SPECUSER_SRB_OVER_HSDPA_DISABLED_S
WITCH:0,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITC
H:0, SPECUSER_EFACH_DISABLED_SWITCH:0,
SPECUSER_ERACH_DISABLED_SWITCH:
0,SPECUSER_PCH_FACH2EFACH_DISABLED_S
WITCH:0,SPECUSER_INHIBIT_D2P_SWITCH:
0,H_SERV_CELL_CHG_MSG_OPT_DISABLED_S
WITCH:
0,EFACH_ERACH_UE_D2P_DISABLED_SWITCH
:
0,SPECUSER_DL_BLER_MEAS_DISABLED_SWI
TCH:
0,SPECUSER_AGPS_MEAS_DISABLED_SWITCH
:
0,SPECUSER_UE_TX_PWR_MEAS_DISABLED_S
WITCH:
0,SPECUSER_CELLID_RTT_MEAS_DISABLED_S
WITCH:
0,FAST_H_SERV_CELL_CHANGE_DISABLED_S
WITCH:
0,SPECUSER_SFDC_HSDPA_DISABLED_SWITC
H:
0,SPECUSER_DF3C_HSDPA_DISABLED_SWITC
H:
0,SPECUSER_FASTMULRLSETUP_DISABLED_S
WITCH:0,SPECUSER_R6_EFACH_CMP_SWITCH:
0,SPECUSER_IFFASTMULRL_CMP_DISABLED_
SWITCH:
0,SPECUSER_AGPS_MEAS_ENABLED_SWITCH:
0,SPECUSER_ENABLE_RPRT_AGPR_MR_ONCE
_SWITCH:
0,SPECUSER_PS_SETUP_DCH0K_DISABLED_S
WITCH:
0,SPECUSER_FACH_CONSIS_OPTI_DISABLE_S
WITCH:
0,SPECUSER_ADJACENT_FREQ_DISABLED_SW
ITCH:
0,SPECUSER_RL_PERFORMANCE_OPT_SWITC
H:0
DISCARD_AFTER_MAX_DAT_RETRANSMISSIO
NS, NO_DISCARD
Unit: None
Actual Value Range:
TIMER_BASED_WITH_EXPLICIT_SIGNALLING,
DISCARD_AFTER_MAX_DAT_RETRANSMISSIO
NS, NO_DISCARD
Default Value: None
DISCARD_AFTER_MAX_DAT_RETRANSMISSIO
NS, NO_DISCARD
Unit: None
Actual Value Range:
TIMER_BASED_WITH_EXPLICIT_SIGNALLING,
DISCARD_AFTER_MAX_DAT_RETRANSMISSIO
NS, NO_DISCARD
Default Value: None
HoAsuT BSC690 SET WRFD- Call Meaning: A timer to RNC wait for the response to
mr 0 USTAT 140103 Reestabl active set update in soft handover procedure.
ETIME WRFD- ishment GUI Value Range: 100~300000
R 020203 Inter Unit: ms
WRFD- RNC
Soft Actual Value Range: 100~300000
020202
Handov Default Value: 5000
er
Intra
RNC
Soft
Handov
er
HoAsuT BSC691 SET WRFD- Call Meaning: A timer to RNC wait for the response to
mr 0 USTAT 140103 Reestabl active set update in soft handover procedure.
ETIME WRFD- ishment GUI Value Range: 100~300000
R 020203 Inter Unit: ms
WRFD- RNC
Soft Actual Value Range: 100~300000
020202
Handov Default Value: 5000
er
Intra
RNC
Soft
Handov
er
HoPhyc BSC690 SET WRFD- Call Meaning: A timer to RNC wait for the response to
hRecfgT 0 USTAT 140103 Reestabl physical channel reconfiguration in hard handover
mr ETIME WRFD- ishment procedure.
R 020301 Intra GUI Value Range: 100~300000
WRFD- Frequen Unit: ms
020302 cy Hard
Handov Actual Value Range: 100~300000
WRFD- er Default Value: 5000
020304
Inter
Frequen
cy Hard
Handov
er Based
on
Coverag
e
Inter
Frequen
cy Hard
Handov
er Based
on DL
QoS
HoPhyc BSC691 SET WRFD- Call Meaning: A timer to RNC wait for the response to
hRecfgT 0 USTAT 140103 Reestabl physical channel reconfiguration in hard handover
mr ETIME WRFD- ishment procedure.
R 020301 Intra GUI Value Range: 100~300000
WRFD- Frequen Unit: ms
020302 cy Hard
Handov Actual Value Range: 100~300000
WRFD- er Default Value: 5000
020304
Inter
Frequen
cy Hard
Handov
er Based
on
Coverag
e
Inter
Frequen
cy Hard
Handov
er Based
on DL
QoS
RbRecfg BSC690 SET WRFD- 3GPP Meaning: A timer used to wait for the RB
RspTmr 0 USTAT 010101 R9 reconfiguration response from UE in the RB
ETIME WRFD- Specific procedure.
R 140103 ations GUI Value Range: 300~300000
Call Unit: ms
Reestabl
ishment Actual Value Range: 300~300000
Default Value: 5000
RbRecfg BSC691 SET WRFD- 3GPP Meaning: A timer used to wait for the RB
RspTmr 0 USTAT 010101 R9 reconfiguration response from UE in the RB
ETIME WRFD- Specific procedure.
R 140103 ations GUI Value Range: 300~300000
Call Unit: ms
Reestabl
ishment Actual Value Range: 300~300000
Default Value: 5000
RbRelR BSC690 SET WRFD- 3GPP Meaning: A timer to RNC wait for the RB release
spTmr 0 USTAT 010101 R9 response from UE in the RB procedure.
ETIME WRFD- Specific GUI Value Range: 300~300000
R 140103 ations
Unit: ms
Call
Reestabl Actual Value Range: 300~300000
ishment Default Value: 5000
RbRelR BSC691 SET WRFD- 3GPP Meaning: A timer to RNC wait for the RB release
spTmr 0 USTAT 010101 R9 response from UE in the RB procedure.
ETIME WRFD- Specific GUI Value Range: 300~300000
R 140103 ations
Unit: ms
Call
Reestabl Actual Value Range: 300~300000
ishment Default Value: 5000
H, RL_PROCEDURE_OPT_SWITCH,
CU_OVERLAP_OPT_SWITCH,
DRNC_DEL_RL_AFTER_CELL_UPD_RELOC_S
WITCH, ADJUST_CNID_WITH_CN,
RAB_REL_FOC_SUCCESS_RCV_SRB_RESET,
CS_TRIG_PS_F2D_SWITCH,
DEAL_RL_RECFG_CORRECT_SWITCH,
RB_RECFG_RL_REEST_MDC_ROLL_BACK_SWI
TCH, CODE_CONFLICT_RL_REEST_SWITCH,
RELOC_IN_AMR_NOISE_DETECT_SWITCH,
CMP_NO_ACTIVE_CFN_OPT_SWITCH,
NON122_AMR_HHO_ROLLBACK_SWITCH,
VQI_AFTER_DT_CONNECT_SWITCH,
FACH_CU_RELOC_RB_MSG_COMP_SWITCH,
SRNS_PROCEDURE_OPTIMIZE_SWITCH,
CALL_RE_ESTAB_CROSS_WITH_SYSOUT_SWI
TCH, DRNC_BUFF_RL_RECFG_PREP_SWITCH,
PS_DCH0K_RB_MSG_OPT_SWITCH,
PS_DSCR_IU_REL_COMPATIBLE_SWITCH
Unit: None
Actual Value Range:
FACH_RB_REL_CU_CROSS_OPT_SWITCH,
CMCF_CHECK_CMP_SWITCH,
ASU_RSP_FAIL_REL_UE,
CELL_PCH_UES_OPT_SWITCH,
DRNC_NOTICE_NODEB_SRNC_VEST_SWITCH,
UMI_WITHOUT_NEWHRNTI_IN_CELLDCH_SW
ITCH,
CCH_IUR_CELLUPT_FAIL_DSCR_SWITCH,
IUB_TRM_PREALLOC_OPT_SWITCH,
SRB_EDCH_RECFG_OPT_SWITCH,
BASED_IUUP_PEERADDR_PFM_OPT_SWITCH,
DRNC_SUPP_RL_ADD_WITH_SRV_CELL_CHG,
OPTI_REL_UE_AFTER_IRAT_RESEL_SWITCH,
U2L_CSFB_FAST_RETURN_PROC_OPTI_SWITC
H,
RL_PROCEDURE_OPT_SWITCH,
CU_OVERLAP_OPT_SWITCH,
DRNC_DEL_RL_AFTER_CELL_UPD_RELOC_S
WITCH,
ADJUST_CNID_WITH_CN,
RAB_REL_FOC_SUCCESS_RCV_SRB_RESET,
CS_TRIG_PS_F2D_SWITCH,
DEAL_RL_RECFG_CORRECT_SWITCH,
RB_RECFG_RL_REEST_MDC_ROLL_BACK_SWI
TCH,
CODE_CONFLICT_RL_REEST_SWITCH,
RELOC_IN_AMR_NOISE_DETECT_SWITCH,
CMP_NO_ACTIVE_CFN_OPT_SWITCH,
NON122_AMR_HHO_ROLLBACK_SWITCH,
VQI_AFTER_DT_CONNECT_SWITCH,
FACH_CU_RELOC_RB_MSG_COMP_SWITCH,
SRNS_PROCEDURE_OPTIMIZE_SWITCH,
CALL_RE_ESTAB_CROSS_WITH_SYSOUT_SWI
TCH,
DRNC_BUFF_RL_RECFG_PREP_SWITCH,
PS_DCH0K_RB_MSG_OPT_SWITCH,
PS_DSCR_IU_REL_COMPATIBLE_SWITCH
Default Value:
FACH_RB_REL_CU_CROSS_OPT_SWITCH:
0,CMCF_CHECK_CMP_SWITCH:
0,ASU_RSP_FAIL_REL_UE:
0,CELL_PCH_UES_OPT_SWITCH:
0,DRNC_NOTICE_NODEB_SRNC_VEST_SWITC
H:
0,UMI_WITHOUT_NEWHRNTI_IN_CELLDCH_S
WITCH:
0,CCH_IUR_CELLUPT_FAIL_DSCR_SWITCH:
0,IUB_TRM_PREALLOC_OPT_SWITCH:
0,SRB_EDCH_RECFG_OPT_SWITCH:
0,BASED_IUUP_PEERADDR_PFM_OPT_SWITCH
:
0,DRNC_SUPP_RL_ADD_WITH_SRV_CELL_CH
G:
0,OPTI_REL_UE_AFTER_IRAT_RESEL_SWITCH:
0,U2L_CSFB_FAST_RETURN_PROC_OPTI_SWIT
CH:0,RL_PROCEDURE_OPT_SWITCH:
0,CU_OVERLAP_OPT_SWITCH:
0,DRNC_DEL_RL_AFTER_CELL_UPD_RELOC_S
WITCH:0,ADJUST_CNID_WITH_CN:
0,RAB_REL_FOC_SUCCESS_RCV_SRB_RESET:
0,CS_TRIG_PS_F2D_SWITCH:
0,DEAL_RL_RECFG_CORRECT_SWITCH:
0,RB_RECFG_RL_REEST_MDC_ROLL_BACK_S
WITCH:
0,CODE_CONFLICT_RL_REEST_SWITCH:
0,RELOC_IN_AMR_NOISE_DETECT_SWITCH:
0,CMP_NO_ACTIVE_CFN_OPT_SWITCH:
0,NON122_AMR_HHO_ROLLBACK_SWITCH:
0,VQI_AFTER_DT_CONNECT_SWITCH:
0,FACH_CU_RELOC_RB_MSG_COMP_SWITCH:
0,SRNS_PROCEDURE_OPTIMIZE_SWITCH:
0,CALL_RE_ESTAB_CROSS_WITH_SYSOUT_SW
ITCH:
0,DRNC_BUFF_RL_RECFG_PREP_SWITCH:
0,PS_DCH0K_RB_MSG_OPT_SWITCH:
0,PS_DSCR_IU_REL_COMPATIBLE_SWITCH:1
H, RL_PROCEDURE_OPT_SWITCH,
CU_OVERLAP_OPT_SWITCH,
DRNC_DEL_RL_AFTER_CELL_UPD_RELOC_S
WITCH, ADJUST_CNID_WITH_CN,
RAB_REL_FOC_SUCCESS_RCV_SRB_RESET,
CS_TRIG_PS_F2D_SWITCH,
DEAL_RL_RECFG_CORRECT_SWITCH,
RB_RECFG_RL_REEST_MDC_ROLL_BACK_SWI
TCH, CODE_CONFLICT_RL_REEST_SWITCH,
RELOC_IN_AMR_NOISE_DETECT_SWITCH,
CMP_NO_ACTIVE_CFN_OPT_SWITCH,
NON122_AMR_HHO_ROLLBACK_SWITCH,
VQI_AFTER_DT_CONNECT_SWITCH,
FACH_CU_RELOC_RB_MSG_COMP_SWITCH,
SRNS_PROCEDURE_OPTIMIZE_SWITCH,
CALL_RE_ESTAB_CROSS_WITH_SYSOUT_SWI
TCH, DRNC_BUFF_RL_RECFG_PREP_SWITCH,
PS_DCH0K_RB_MSG_OPT_SWITCH,
PS_DSCR_IU_REL_COMPATIBLE_SWITCH
Unit: None
Actual Value Range:
FACH_RB_REL_CU_CROSS_OPT_SWITCH,
CMCF_CHECK_CMP_SWITCH,
ASU_RSP_FAIL_REL_UE,
CELL_PCH_UES_OPT_SWITCH,
DRNC_NOTICE_NODEB_SRNC_VEST_SWITCH,
UMI_WITHOUT_NEWHRNTI_IN_CELLDCH_SW
ITCH,
CCH_IUR_CELLUPT_FAIL_DSCR_SWITCH,
IUB_TRM_PREALLOC_OPT_SWITCH,
SRB_EDCH_RECFG_OPT_SWITCH,
BASED_IUUP_PEERADDR_PFM_OPT_SWITCH,
DRNC_SUPP_RL_ADD_WITH_SRV_CELL_CHG,
OPTI_REL_UE_AFTER_IRAT_RESEL_SWITCH,
U2L_CSFB_FAST_RETURN_PROC_OPTI_SWITC
H,
RL_PROCEDURE_OPT_SWITCH,
CU_OVERLAP_OPT_SWITCH,
DRNC_DEL_RL_AFTER_CELL_UPD_RELOC_S
WITCH,
ADJUST_CNID_WITH_CN,
RAB_REL_FOC_SUCCESS_RCV_SRB_RESET,
CS_TRIG_PS_F2D_SWITCH,
DEAL_RL_RECFG_CORRECT_SWITCH,
RB_RECFG_RL_REEST_MDC_ROLL_BACK_SWI
TCH,
CODE_CONFLICT_RL_REEST_SWITCH,
RELOC_IN_AMR_NOISE_DETECT_SWITCH,
CMP_NO_ACTIVE_CFN_OPT_SWITCH,
NON122_AMR_HHO_ROLLBACK_SWITCH,
VQI_AFTER_DT_CONNECT_SWITCH,
FACH_CU_RELOC_RB_MSG_COMP_SWITCH,
SRNS_PROCEDURE_OPTIMIZE_SWITCH,
CALL_RE_ESTAB_CROSS_WITH_SYSOUT_SWI
TCH,
DRNC_BUFF_RL_RECFG_PREP_SWITCH,
PS_DCH0K_RB_MSG_OPT_SWITCH,
PS_DSCR_IU_REL_COMPATIBLE_SWITCH
Default Value:
FACH_RB_REL_CU_CROSS_OPT_SWITCH:
0,CMCF_CHECK_CMP_SWITCH:
0,ASU_RSP_FAIL_REL_UE:
0,CELL_PCH_UES_OPT_SWITCH:
0,DRNC_NOTICE_NODEB_SRNC_VEST_SWITC
H:
0,UMI_WITHOUT_NEWHRNTI_IN_CELLDCH_S
WITCH:
0,CCH_IUR_CELLUPT_FAIL_DSCR_SWITCH:
0,IUB_TRM_PREALLOC_OPT_SWITCH:
0,SRB_EDCH_RECFG_OPT_SWITCH:
0,BASED_IUUP_PEERADDR_PFM_OPT_SWITCH
:
0,DRNC_SUPP_RL_ADD_WITH_SRV_CELL_CH
G:
0,OPTI_REL_UE_AFTER_IRAT_RESEL_SWITCH:
0,U2L_CSFB_FAST_RETURN_PROC_OPTI_SWIT
CH:0,RL_PROCEDURE_OPT_SWITCH:
0,CU_OVERLAP_OPT_SWITCH:
0,DRNC_DEL_RL_AFTER_CELL_UPD_RELOC_S
WITCH:0,ADJUST_CNID_WITH_CN:
0,RAB_REL_FOC_SUCCESS_RCV_SRB_RESET:
0,CS_TRIG_PS_F2D_SWITCH:
0,DEAL_RL_RECFG_CORRECT_SWITCH:
0,RB_RECFG_RL_REEST_MDC_ROLL_BACK_S
WITCH:
0,CODE_CONFLICT_RL_REEST_SWITCH:
0,RELOC_IN_AMR_NOISE_DETECT_SWITCH:
0,CMP_NO_ACTIVE_CFN_OPT_SWITCH:
0,NON122_AMR_HHO_ROLLBACK_SWITCH:
0,VQI_AFTER_DT_CONNECT_SWITCH:
0,FACH_CU_RELOC_RB_MSG_COMP_SWITCH:
0,SRNS_PROCEDURE_OPTIMIZE_SWITCH:
0,CALL_RE_ESTAB_CROSS_WITH_SYSOUT_SW
ITCH:
0,DRNC_BUFF_RL_RECFG_PREP_SWITCH:
0,PS_DCH0K_RB_MSG_OPT_SWITCH:
0,PS_DSCR_IU_REL_COMPATIBLE_SWITCH:1
T302 BSC690 SET WRFD- Intra Meaning: Timer 302. T302 starts when a UE sends a
0 UCONN 010901 RNC CELL UPDATE/URA UPDATE message and stops
MODET WRFD- URA when the UE receives a CELL UPDATE
IMER 010902 Update CONFIRM/URA UPDATE CONFIRM message.
Inter When T302 expires, the UE resends a CELL
WRFD- UPDATE/URA UPDATE message if the value of the
010101 RNC
URA counter V302 is smaller than or equal to that of the
WRFD- Update parameter N302. If the value of V302 is larger than
040100 that of N302 when T302 expires, the UE enters the
3GPP idle mode. The protocol-defined default value is 4000.
WRFD- R9
140103 The value of this parameter is contained in SIB1
Specific messages.
WRFD- ations
010801 GUI Value Range: D100, D200, D400, D600, D800,
Flow D1000, D1200, D1400, D1600, D1800, D2000,
WRFD- Control D3000, D4000, D6000, D8000
010802 Call Unit: ms
Reestabl
ishment Actual Value Range: 100, 200, 400, 600, 800, 1000,
1200, 1400, 1600, 1800, 2000, 3000, 4000, 6000,
Intra 8000
RNC
Cell Default Value: D2000
Update
Inter
RNC
Cell
Update
T302 BSC691 SET WRFD- Intra Meaning: Timer 302. T302 starts when a UE sends a
0 UCONN 010901 RNC CELL UPDATE/URA UPDATE message and stops
MODET WRFD- URA when the UE receives a CELL UPDATE
IMER 010902 Update CONFIRM/URA UPDATE CONFIRM message.
Inter When T302 expires, the UE resends a CELL
WRFD- UPDATE/URA UPDATE message if the value of the
010101 RNC
URA counter V302 is smaller than or equal to that of the
WRFD- Update parameter N302. If the value of V302 is larger than
040100 that of N302 when T302 expires, the UE enters the
3GPP idle mode. The protocol-defined default value is 4000.
WRFD- R9
140103 The value of this parameter is contained in SIB1
Specific messages.
WRFD- ations
010801 GUI Value Range: D100, D200, D400, D600, D800,
Flow D1000, D1200, D1400, D1600, D1800, D2000,
WRFD- Control D3000, D4000, D6000, D8000
010802 Call Unit: ms
Reestabl
ishment Actual Value Range: 100, 200, 400, 600, 800, 1000,
1200, 1400, 1600, 1800, 2000, 3000, 4000, 6000,
Intra 8000
RNC
Cell Default Value: D2000
Update
Inter
RNC
Cell
Update
N302 BSC690 SET WRFD- Intra Meaning: Maximum number of retransmissions of the
0 UCONN 010901 RNC CELL UPDATE/URA UPDATE message. The
MODET WRFD- URA protocol-defined default value is 3. The value of this
IMER 010902 Update parameter is contained in SIB1 messages.
WRFD- Inter GUI Value Range: 0~7
010101 RNC Unit: None
URA
WRFD- Update Actual Value Range: 0~7
140103 Default Value: 3
3GPP
WRFD- R9
010801 Specific
WRFD- ations
010802 Call
Reestabl
ishment
Intra
RNC
Cell
Update
Inter
RNC
Cell
Update
N302 BSC691 SET WRFD- Intra Meaning: Maximum number of retransmissions of the
0 UCONN 010901 RNC CELL UPDATE/URA UPDATE message. The
MODET WRFD- URA protocol-defined default value is 3. The value of this
IMER 010902 Update parameter is contained in SIB1 messages.
WRFD- Inter GUI Value Range: 0~7
010101 RNC Unit: None
URA
WRFD- Update Actual Value Range: 0~7
140103 Default Value: 3
3GPP
WRFD- R9
010801 Specific
WRFD- ations
010802 Call
Reestabl
ishment
Intra
RNC
Cell
Update
Inter
RNC
Cell
Update
N313 BSC690 SET WRFD- 3GPP Meaning: Maximum number of successive "out of
0 UCONN 010101 R9 sync" indications received from Layer 1. The
MODET WRFD- Specific protocol-defined default value is 20. The value of this
IMER 140103 ations parameter is contained in SIB1 messages.
WRFD- Call GUI Value Range: D1, D2, D4, D10, D20, D50,
010802 Reestabl D100, D200
ishment Unit: None
WRFD-
010801 Inter Actual Value Range: 1, 2, 4, 10, 20, 50, 100, 200
RNC
Cell Default Value: D50
Update
Intra
RNC
Cell
Update
N313 BSC691 SET WRFD- 3GPP Meaning: Maximum number of successive "out of
0 UCONN 010101 R9 sync" indications received from Layer 1. The
MODET WRFD- Specific protocol-defined default value is 20. The value of this
IMER 140103 ations parameter is contained in SIB1 messages.
WRFD- Call GUI Value Range: D1, D2, D4, D10, D20, D50,
010802 Reestabl D100, D200
ishment Unit: None
WRFD-
010801 Inter Actual Value Range: 1, 2, 4, 10, 20, 50, 100, 200
RNC
Cell Default Value: D50
Update
Intra
RNC
Cell
Update
N315 BSC690 SET WRFD- 3GPP Meaning: Maximum number of successive "in sync"
0 UCONN 010101 R9 indications received from Layer 1 after T313 starts.
MODET WRFD- Specific The protocol-defined default value is 1. The value of
IMER 140103 ations this parameter is contained in SIB1 messages.
WRFD- Call GUI Value Range: D1, D2, D4, D10, D20, D50,
010802 Reestabl D100, D200, D400, D600, D800, D1000
ishment Unit: None
WRFD-
010801 Inter Actual Value Range: 1, 2, 4, 10, 20, 50, 100, 200, 400,
RNC 600, 800, 1000
Cell
Update Default Value: D1
Intra
RNC
Cell
Update
N315 BSC691 SET WRFD- 3GPP Meaning: Maximum number of successive "in sync"
0 UCONN 010101 R9 indications received from Layer 1 after T313 starts.
MODET WRFD- Specific The protocol-defined default value is 1. The value of
IMER 140103 ations this parameter is contained in SIB1 messages.
WRFD- Call GUI Value Range: D1, D2, D4, D10, D20, D50,
010802 Reestabl D100, D200, D400, D600, D800, D1000
ishment Unit: None
WRFD-
010801 Inter Actual Value Range: 1, 2, 4, 10, 20, 50, 100, 200, 400,
RNC 600, 800, 1000
Cell
Update Default Value: D1
Intra
RNC
Cell
Update
Statistic BSC690 SET WRFD- Call Meaning: Timer started after radio link (RL)
TmrAfte 0 USTAT 140103 Reestabl reestablishment to measure the number of Iu Release
rRlReEs ETIME ishment Command or RAB Assignment Request messages
t R received from the CN. If this parameter is set to 0, the
measurement will not be performed.
GUI Value Range: 0~30
Unit: s
Actual Value Range: 0~30
Default Value: 5
Statistic BSC691 SET WRFD- Call Meaning: Timer started after radio link (RL)
TmrAfte 0 USTAT 140103 Reestabl reestablishment to measure the number of Iu Release
rRlReEs ETIME ishment Command or RAB Assignment Request messages
t R received from the CN. If this parameter is set to 0, the
measurement will not be performed.
GUI Value Range: 0~30
Unit: s
Actual Value Range: 0~30
Default Value: 5
12 Counters
13 Glossary
14 Reference Documents