INTRODUCTIO TITLE PAGE single column that should be self N format. Leave one explanatory. Table The title page line space between titles should go Indian Welding should include: paragraphs, but do above the table and Journal (IWJ) not indent the first figure captions (ISSN 0046-9092) The name(s) of the line of a new below the figure. is the official journal author(s) paragraph. Page Leave one line of the Indian A concise and numbers should be space between the Institute of informative title centered at the title and the table or Welding (IIW-India) The affiliation(s) bottom. Insert a line figure. Figures and being published and address(es) of space after the final tables are to be quarterly since the authors paragraph in a numbered 1968. Volume 50 is The e-mail address, section. consequently. Refer being published in telephone and fax these inside the text 2017. Articles numbers of the First level heading as Table 1 or Fig. 1, published in it are corresponding should be etc. In addition, indexed by Indian author consequently each figure should Citation Index, numbered like 1., be given as EBSCO, USA, i- ABSTRACT 2., etc., left justified, separate file(s), Scholar, and j- all caps and bold. naming the file as Gate. This journal is An abstract should Insert one line Fig. 1, Fig. 2, etc. recently included in be of 150 to 250 space before and Figures (including the list of approved words and it should after a first level photographs, line journals of the not contain any heading. drawing, etc.) must University Grant undefined be clear and Commission abbreviations or Second level reproducible. (UGC). This journal unspecified heading should be includes selected references. numbered REFERENCES technical articles consequently like Citation published in 1.1., 1.2., 2.1., 2.2., KEYWORDS etc., left justified, Welding Journal of The list of American Welding with running letter references should Four to six and bold, with one Society. Articles are keywords should be only include works invited in the broad line space above it. that are cited in the included. areas of welding text and that have and cutting for The heading of been published or TEXT Abstract, Appendix accepted for publication in the Text Formatting IWJ as per the and References are publication. following to be all caps, 11- Reference citations Manuscripts should point, bold, and in the text should be categories; be submitted in centered, with two identified by editable Word files line spaces above, numbers in square a) Original as well as in PDF papers and one below. brackets. Some version. examples: b) Conference Margins and papers (For Figures and Spacing Tables The effect has been journal special widely studied [1-5]. The top, bottom, Figures and tables The same results issues, etc.) left, and right c) Critical should appear close were observed by margins should be to their first citation Reddy et al. [6]. assessments kept one inch each. / Reviews inside the text. The text of the Each table or figure Example d) Case studies / paper should be Application should be centered. [1] Badheka VJ single-spaced and Each table and areas fully justified in 11- and Albert SK each figure should (2009); point Arial font in have centered titles
Revised on September 3, 2017
Improving the and if needed, EDITORIAL weld author(s) will be BOARD ASSIGNING penetration by required to DOI application of incorporate Chief Editor: Prof. oxide coating in necessary changes Santanu Das DOI (digital object GTAW of P91 in the manuscript Joint Editors: Dr. identifier) is being steel, Proc. Nat. for final acceptance. D.V. Kulkarni assigned to Weld. Sem., research articles Kolkata, India, PLAGIARISM Members: Prof. recently published, p.18. CHECKING T.K. Pal, Mr. P.K. or to the [2] Sabiruddin K, Das, forthcoming articles Das S and All the contributed Dr. A.K. Bhaduri, Dr. of the IWJ. Bhattacharya A articles are G. Madhusudan 10.22486/iwj/2017/ (2009); plagiarism checked Reddy, v50/i2/146561 is a Application of by Crossref system Dr. Amitava De, Dr. typical DOI for a the analytic powered by Shaju K. Albert, published article. hierarchy ithenticate. A Prof. G.L. Datta, Mr. process for maximum of 10% Rahul Sengupta, CONTACT optimization of similarity content Dr. G. process ADDRESS will be allowed to a Padmanabham, parameters in research paper for Dr. V. GMAW, IWJ, publishing in the Balasubramanian, The Chief 42(1), pp.38-46. IWJ. Dr. Mahadev Editor Shome. Indian Welding APPENDIX COPYRIGHT Journal AND Representative of The Indian ACKNOWLEDG Authors will be AWS: Mr. Andrew Cullison Institute of MENT asked to transfer copyright of the and Mr. Jeffery Welding article to the Indian Weber. 3A, Dr. U. N. Appendices, if Brahmachari needed absolutely, Institute of Welding (IIW-India). To this INDIAN Street, should be placed after references effect, the WELDING Kolkata- 700 017. section. Uses of corresponding JOURNAL appendices are not author on behalf of Email: other authors, if ARCHIVE iwj.iiw@gmail.com encouraged, in general. any, has to sign and submit a The work of making Website (IIW- Acknowledgment, a complete Archive appendices, etc., if Declaration Form India): available in IIW- of articles published www.iiwindia.com any, may follow the in the Indian References section. India website. Welding Journal Website (IWJ): since Volume 1 http://www.i- PEER REVIEW 1968 is progressing scholar.in/index.php PROCESS in full swing. /IWJ. Substantial work is Manuscripts of done and many contributed articles published articles submitted under may be found in i- each category will Scholar and j-Gate be double-blind platform. Readers peer reviewed. may please surf the Author(s) will be website: communicated with http://www.i- the review results, scholar.in/index.p hp/IWJ.
Type: A Primer of Information About the Mechanical Features of Printing Types: Their Sizes, Font Schemes, &c. with a Brief Description of Their Manufacture