Académique Documents
Professionnel Documents
Culture Documents
Issue 01
Date 2014-04-30
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Contents
2 Overview.........................................................................................................................................4
2.1 UE State Transitions.......................................................................................................................................................5
2.2 RRC States......................................................................................................................................................................5
2.3 UE State Transition Types..............................................................................................................................................6
2.4 Relationships Between Service Type and State Transition............................................................................................9
2.5 Trigger Conditions for UE State Transitions..................................................................................................................9
8 Parameters.....................................................................................................................................80
9 Counters......................................................................................................................................392
10 Glossary.....................................................................................................................................401
11 Reference Documents.............................................................................................................402
1.1 Scope
This document describes state transition, including its technical principles, related features,
network impact, and engineering guidelines.
This document requires that readers know the dynamic channel configuration control (DCCC)
mechanism. It is recommended that readers read the DCCC Feature Parameter Description
beforehand.
l Feature change
Changes in features of a specific product version
l Editorial change
Changes in wording or addition of information that was not described in the earlier version
RAN16.0 01 (2014-04-30)
This issue does not include any changes.
Editorial Added the descriptions about the feature and function None
change differences between NodeBs of different types. For
details, see section 1.4 Differences Between Base
Station Types.
Micro l BTS3803E
l BTS3902E
LampSite DBS3900
The features described in this document are implemented in the same way on macro, micro, and
LampSite base stations.
2 Overview
After a UE sets up a radio resource control (RRC) connection, it enters UTRAN connected mode.
The RNC monitors UE behaviors and controls UE state transitions. When there are data
transmission requirements, services can be processed in time. When there is no data transmission
requirement, network resources can be saved.
Huawei has implemented state transitions between idle mode and UTRAN connected mode as
well as state transitions in UTRAN connected mode.
After a UE sets up an RRC connection, it enters UTRAN connected mode. The four states in
UTRAN connected mode are as follows:
l CELL_DCH state
A UE in this state occupies dedicated channel resources and consumes a large amount of
radio resources. This state is suitable for high-speed data transmission.
l CELL_FACH state
A UE in this state uses the common channel to send or receive data, which occupies only
a small amount of resources. Because of resource limitations on the RACH and FACH, the
CELL_FACH state is suitable for low-speed data transmission.
l CELL_PCH state
On the uplink, a UE in this state cannot transmit signaling messages. If the UE has data to
transmit on the uplink, it needs to go through the cell update procedure to transit to the
CELL_FACH or CELL_DCH state.
On the downlink, the UE uses the discontinuous reception (DRX) technique to monitor
messages on the PCH at a given moment. The purpose is to identify paging messages. If
the UE in the CELL_PCH state is on a WCDMA network, the UTRAN can learn which
cell the UE is camping on and can page the UE within this cell. After moving to another
cell, the UE needs to send a CELL UPDATE message to perform cell reselection.
l URA_PCH state
This state differs from the CELL_PCH state in that, if the UE in the URA_PCH state is on
a WCDMA network, the UTRAN can learn which UTRAN registration area (URA) the
UE is in and can page the UE within this URA. After moving to another URA, the UE
needs to send a URA UPDATE message to perform a URA update.
F2H CELL_FACH to
CELL_DCH (HS-DSCH)
F2E CELL_FACH to
CELL_DCH (E-DCH)
F2CPC CELL_FACH to
CELL_DCH (CPC)
D2Idle 4.2 Always Online Always online RRC connected mode to idle
mode
Figure 2-2 Traffic volume or throughput stays above the event 4A threshold
l Event 4B: As shown in Figure 2-3, if the traffic volume or throughput stays below the
event 4B threshold, event 4B is reported, which may trigger state transitions.
Figure 2-3 Traffic volume or throughput stays below the event 4B threshold
l Cell reselection
If the number of cell reselections exceeds a specified threshold during a specified period,
the UE is considered to be in the state of frequent cell reselections, which may trigger state
transitions.
l UE reentering service area
A UE in URA_PCH state initiates a CELL UPDATE procedure after reentering the service
area, and the cause value of the CELL_Update message is Re-entered Service Area, which
trigger U2U state transmissions.
l UE mobility
When a UE moves to an area with poor coverage, the UE falls back from the E-DCH to
the DCH. When the UE then moves to an area where coverage is not limited, it performs
a D2E retry for DCCC Based on Traffic Volume. For details, see section 3.10 D2D State
Transition.
l Paging or data transmission
When the UTRAN pages a UE or a UE intends to transmit data, state transmissions may
be triggered.
l Cell overload
When a cell is overloaded, the RNC transits the UE state from CELL_DCH (DCH/HS-
DSCH/E-DCH) to CELL_FACH (FACH) to relieve cell load.
l Historical records of data transmission
The RNC predicts future data transmission behaviors of a UE based on historical records:
– If the previous transmission interval for a UE was long, the RNC predicts that the
subsequent transmission interval will be long. When the UE completes data
transmission, the RNC quickly transits the UE state from CELL_DCH to CELL_PCH,
URA_PCH, or CELL_FACH. For details, see 3.12 Smart Fast State Transition.
– If a UE transmitted a large amount of data multiple consecutive times, the RNC predicts
that the UE will transmit a large amount of data next time. When the UE transmits data
next time, the RNC will transit the UE state from CELL_PCH, URA_PCH, or
CELL_FACH to CELL_DCH through a CELL UPDATE procedure. For details, see
3.13 Smart P2D.
D2F state transition has the following channel type shifting (see section 2.3 UE State Transition
Types for details):
l D2F and H2F channel type shifting uses traffic volume-based event 4B measurement.
If the actual traffic volume or throughput of a service stays below the event 4B threshold for a
period specified by "Time to trigger", event 4B is reported. In addition, event 4B cannot be
reported again during the period specified by "Pending time after trigger" to prevent repeated
reporting of event 4B from wasting system resources. See Table 3-1 for the parameters related
to the event 4B threshold, "Time to trigger", and "Pending time after trigger."
When receiving a report on event 4B, the RNC starts the timer for D2F state transition and the
counters for UL and DL event 4B reports. If the numbers of UL and DL event 4B reports are
greater than or equal to the corresponding D2F transition threshold before the timer expires, then
the D2F state transition is performed when the timer expires. See Table 3-1 for the parameters
related to the D2F state transition timer.
The D2F state transition threshold is the rounded-down value obtained by using the following
equation:
D2F transition threshold = D2F transition time/ (Time to trigger + Pending time after trigger) x
State transition traffic redundancy coefficient
In this equation:
l The D2F state transition time, time to trigger, and pending time after trigger are specified
by the parameters listed in Table 3-1.
l The state transition traffic redundancy coefficient is used to prevent false detection that a
UE is in the low-activity state due to the loss of measurement reports. This coefficient is
configured by using the STATETRANSTRAFFREDUNDCOEF(BSC6900,BSC6910)
parameter.
NOTE
l If the uplink and downlink of a BE service are carried on two different channels, the D2F state transition
time equals the larger of the D2F state transition time for the two channels, and (Time to trigger +
Pending time after trigger) equals the actual value configured for the channels.
l In the case of combined PS services (PS BE service + PS BE service or PS BE service + PS real-time
service), if one of the services meets the state transition conditions, the service first enters the low
activity state. A state transition is performed until the other service also meets the state transition
conditions.
l In the case of combined services (PS BE service + CS service), if the PS BE service meets the state
transition conditions, the service first enters the low activity state. A state transition is performed until
the CS service is released.
If the uplink and downlink of a BE service are carried on different channels, the RNC identifies
the uplink and downlink and selects different parameters according to Table 3-1.
DraSwitch
(BSC6900,BSC6910):
DRA_PS_NON_BE_STATE_TRANS_SWITCH
DraSwitch
(BSC6900,BSC6910):
DRA_HSDPA_STATE_TRANS_SWITCH
NOTE
If the current service type is non-HSPA, the D2F state transition switch of this service is independent of
HSPA service switch parameters.
After the D2F state transition switch is turned on, whether the D2F state transition takes effect
also depends on DCCC. The details are as follows:
For non-PTT services, to prevent ping-pong state transitions between CELL_DCH and
CELL_FACH, turn on the PERFENH_H2F_OPT_SWITCH under the PerfEnhanceSwitch
(BSC6900,BSC6910) parameter. After the PERFENH_H2F_OPT_SWITCH is turned on,
event 4A and 4B measurements start. If the RNC receives an event 4A report before the D2F
state transition timer expires, and if the uplink throughput is higher than HSUPA4AThrouThd
(BSC6900,BSC6910) or the downlink throughput is higher than HSDPA4ATvmThd
(BSC6900,BSC6910), the RNC stops the D2F state transition timer to prevent unnecessary state
transitions.
For PTT services, to prevent ping-pong state transitions between CELL_DCH and
CELL_FACH, turn on the PERFENH_PTT_H2F_OPT_SWITCH under the
PerfEnhanceSwitch1(BSC6900,BSC6910) parameter to start event 4A and 4B measurements.
If the RNC receives an event 4A report before the D2F state transition timer expires, and if either
of the following conditions is met, the RNC stops the D2F state transition timer to prevent
unnecessary state transitions:
l The measured value of uplink throughput carried in the event 4A report is greater than
(PTTE2FTHROUTHD(BSC6900,BSC6910) + 10bit/s).
l The measured value of downlink traffic volume carried in the event 4A report is greater
than the high-level threshold for PTTDH2FTVMTHD(BSC6900,BSC6910). For example,
if PTTDH2FTVMTHD(BSC6900,BSC6910) is set to 8 bytes, the downlink traffic volume
must be greater than 16 bytes to meet this condition. In this example, "16 bytes" is the high-
level threshold of "8 bytes."
NOTE
The value range of PTTDH2FTVMTHD(BSC6900,BSC6910) is 8, 16, 32, 64, 128, 256, 512, 1024, 2k,
3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k. The unit of this
parameter is byte.
Table 3-3 lists the switch parameters related to air interface exception-based H2F state transition.
Table 3-3 Switch parameters related to air interface exception-based H2F state transition
DraSwitch
(BSC6900,BSC6910):
DRA_HSDPA_STATE_TRANS_SWITCH
The Downlink Transmitted Code Power measurement configuration is sent to the cell serving
the UEs that meet all of the following conditions, and the NodeB checks the transmitted code
power of the DPCH or F-DPCH for HSDPA users:
When the NodeB reports event Ea related to the downlink transmitted code power of a UE, the
RNC measures the traffic volume and throughput on the UE. If the measured traffic volume is
greater than DlBeAbnH2FHIghTvmThd(BSC6900,BSC6910) and the measured throughput is
less than or equal to DlBeAbnH2FLowThrouThd(BSC6900,BSC6910), the RNC regards the
BE service involved in abnormal data transmission. In this situation, the RNC instructs the UE
to perform an H2F transition to release resources and forbids F2D transitions for the UE within
a certain period of time. The RNC triggers a timer (specified by
BeAbnormH2FStateTransTimer(BSC6900,BSC6910)). The timer stops if the conditions for
the air interface exception-based H2F transition are not met. The RNC instructs the UE to
perform an H2F transition when the timer expires and, at the same time, triggers a penalty timer
(specified by AbnH2FPenaltyLen(BSC6900,BSC6910)) for F2D transitions. F2D transitions
are not allowed for the UE until the timer expires.
If the UE processing the BE service receives event Eb related to the downlink transmitted code
power, the RNC stops measuring the throughput on the UE. In addition, the timer (specified by
BeAbnormH2FStateTransTimer(BSC6900,BSC6910)) stops at the same time if it has started.
D2F State Transition Triggered by the Service Release for CS+PS BE Combined
Services
When the DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH under the DraSwitch
(BSC6900,BSC6910) parameter is turned on, the PS BE service in CS+PS BE combined services
is processed as follows:
l If the PS BE service rate is 0 kbit/s, the PS BE service is not controlled by the timer
ZeroRateUpFailToRelTimerLen(BSC6900,BSC6910). That is, when the timer expires,
the PS service is not released.
l If the DRA_PS_BE_STATE_TRANS_SWITCH under the DraSwitch
(BSC6900,BSC6910) parameter is turned on and the CS service is released, D2F state
transition is triggered for the PS BE service as long as the trigger conditions are met,
regardless of whether the PS BE service rate is 0 kbit/s. If the PS BE service is HSDPA or
HSUPA service, the DRA_HSDPA_STATE_TRANS_SWITCH or
DRA_HSUPA_STATE_TRANS_SWITCH under the DraSwitch(BSC6900,BSC6910)
parameter also needs to be turned on.
For a BE service carried on the DCH, the RNC reduces the service rate to the low-activity state
threshold LittleRateThd(BSC6900,BSC6910) to save DCH resources if the following
conditions are met:
l The UE cannot perform state transitions but stays in CELL_DCH, for example,
DRA_PS_BE_STATE_TRANS_SWITCH is set to 0.
l The total number of UL and DL event 4B reports is greater than or equal to the D2F state
transition threshold before the transition timer expires.
For combined services, the RNC determines whether to enable the low activity state function
and reduces the service rate on a per service basis. For example, in the case of BE and CS
combined services, the RNC performs processing only for BE services. In addition, when the
uplink and downlink of a BE services are carried on different channels, the RNC determines
whether to enable the low activity state function and reduces the service rate for the uplink and
downlink separately.
Note that the low activity state function is disabled when LittleRateThd(BSC6900,BSC6910)
is greater than or equal to UlDcccRateThd(BSC6900,BSC6910) and DlDcccRateThd
(BSC6900,BSC6910).
DraSwitch
(BSC6900,BSC6910):
DRA_PS_NON_BE_STATE_TRANS_SWITCH
If the actual traffic volume of a service stays below the event 4B threshold for a period specified
by "Time to trigger", event 4B is reported. In addition, event 4B cannot be reported again during
the period specified by "Pending time after trigger" to prevent repeated reporting of event 4B
from wasting system resources. See Table 3-5 for the parameters related to the event 4B
threshold, "Time to trigger", and "Pending time after trigger."
When receiving a report on event 4B, the RNC starts the timer for F2P state transition and the
counters for UL and DL event 4B reports. If the numbers of UL and DL event 4B reports are
greater than the corresponding F2P transition threshold before the timer expires, then the F2P
state transition is performed when the timer expires. See Table 3-5 for the parameters related
to the F2P state transition timer.
The F2P state transition threshold is the rounded-down value obtained by using the following
equation:
F2P transition threshold = F2P transition time/ (Time to trigger + Pending time after trigger) x
State transition traffic redundancy coefficient
In this equation:
l The F2P state transition time, time to trigger, and pending time after trigger are specified
by the parameters listed in Table 3-5.
l The state transition traffic redundancy coefficient for F2P state transition is also configured
by using STATETRANSTRAFFREDUNDCOEF(BSC6900,BSC6910).
To increases the accuracy for triggering F2P transitions, inactivity-based F2P is introduced. The
RNC performs inactivity-related measurements. If a UE does not receive or transmit any data
during a period specified by the inactivity timer and the RLC buffer is blank, the RNC enables
the UE to transit from the CELL_FACH state to the CELL_PCH state (abbreviated as F2P).
After enabling, this function replaces the F2P based on 4b event.
Inactivity-based F2P increases the accuracy for triggering F2P transitions, and UEs receiving
or transmitting small packets will not experience F2P transitions. This function sets more strict
conditions for triggering F2P transitions and therefore reduces the reconfigurations for F2P2F
transitions (transitions from CELL_FACH to CELL_PCH and then to CELL_FACH again).
Based on the same traffic model, this function reduces signaling messages used for RB
reconfigurations and cell updates and does not significantly affect the distribution of the number
of users in the CELL_FACH and CELL_PCH states.
Inactivity-based F2P is disabled by default. To enable it, run the RNC MML command SET
UCORRMPARA or turn on PerfEnhanceSwitch3(BSC6900,BSC6910):
F2U state transition uses the same parameter settings and trigger conditions as F2P state
transition.
Table 3-6 lists the switch parameters related to F2U state transition.
DraSwitch
(BSC6900,BSC6910):
DRA_PS_NON_BE_STATE_TRANS_SWITCH
The relationships between F2U and other state transitions are as follows:
Table 3-7 lists the switch parameters related to P2U state transition.
DraSwitch
(BSC6900,BSC6910):
DRA_PS_NON_BE_STATE_TRANS_SWITCH
Before the state transition, the UE is in the CELL_PCH state. During the cell reselection, the
UE sends the CELL UPDATE messages to the RNC. Upon receiving the CELL UPDATE
messages, the RNC starts a timer CellReSelectTimer(BSC6900,BSC6910) and counts the
number of CELL UPDATE messages with the cause value of cell reselection. When the timer
expires, the number of CELL UPDATE messages may be greater than the threshold
CellReSelectCounter(BSC6900,BSC6910). If both conditions are met, the RNC initiates a P2U
transition when the UE sends CELL UPDATE messages again. Then, the UE in the CELL_PCH
state will be transited to the URA_PCH state.
NOTE
The UE in the CELL_PCH or URA_PCH state cannot receive or send signaling messages. Therefore, the
P2U state transition involves the transient state CELL_FACH, in which necessary signaling interactions
are performed over the FACH.
Table 3-8 Switch parameters related to P2F and U2F state transitions
DraSwitch
(BSC6900,BSC6910):
DRA_PS_NON_BE_STATE_TRANS_SWITCH
DraSwitch
(BSC6900,BSC6910):
DRA_PS_NON_BE_STATE_TRANS_SWITCH
After returning to the service area, the UE that stays in the URA_PCH state originates a cell
update procedure. If the cell update cause value carried in the CELL UPDATE message is Re-
entered Service Area, the RNC sends a CELL UPDATE CONFIRM message to instruct the UE
to return to the URA_PCH state.
Certain UEs cannot transit from the URA_PCH state to the CELL_PCH state. This reduces the
amount of signaling caused by cell updates and reconfiguration over the air interface.
NOTE
The UE in the URA_PCH state cannot receive or send signaling messages. Therefore, the U2U state
transition involves the transient state CELL_FACH, in which necessary signaling interactions are
performed over the FACH. This means U2F and F2U state transitions are involved in U2U state transition.
DraSwitch
(BSC6900,BSC6910):
DRA_PS_NON_BE_STATE_TRANS_SWITCH
Event 4A report is triggered when the uplink or downlink traffic of a UE exceeds the event 4A
threshold and keeps above the threshold for a certain period (event 4A time to trigger). The F2D
state transition is performed when the UTRAN receives an event 4A report. Then, the RNC
determines the service bearing policies for the UE, such as the transport channel (DCH, HS-
DSCH, or E-DCH) and the target rate. If the cell accommodating the UE is overloaded, the RNC
does not allow the UE to perform F2D state transition.
Table 3-11 lists the threshold, time to trigger, and target rate for event 4A and F2D state
transition.
Table 3-11 Threshold, time to trigger, and target rate for event 4A and F2D state transition
Table 3-12 lists the switch parameters related to F2D state transition caused by FACH
congestion.
Table 3-12 Switch parameters related to F2D state transition caused by FACH congestion
When you find the FACH of a cell is congested, you can manually turn on this function in the
cell to relieve the FACH congestion.
When the function of F2D State Transition Caused by FACH Congestion is activated, RNC use
the event 4A threshold BeF2DHTvmThdForFACHCong(BSC6900,BSC6910) in the cell to
replace the original RNC-level event 4A thresholds as follows:
l BeF2DTvmThd(BSC6900,BSC6910)
l BeF2HTvmThd(BSC6900,BSC6910)
l BeF2ETvmThd(BSC6900,BSC6910)
NOTE
Table 3-13 Switch parameters related to F2D state transition based on data transmission wait
time
When a UE in the CELL_FACH state is transmitting data, F2D state transition is triggered when
the following condition is met:
The delay of RLC service data unit (SDU) is greater than or equal to data transmission wait time.
The timer for the F2D state transition based on data transmission wait time is
BasedTimeF2DThd(BSC6900,BSC6910).
After performing wait time-based F2D state transition, the RNC does not perform D2F state
transition when the following condition is met:
In weak coverage, the delay of RLC SDU is equal to or greater than data transmission wait time,
which easily triggers the wait time-based F2D state transition. The wait time-based F2D state
transition success rate is relatively low in weak coverage, which reduces the F2D state transition
success rate. RAN15.0 introduces solutions to the reduced success rate of wait time-based F2D
state transitions in weak-coverage areas. If the number of RLC retransmissions is larger than its
threshold, the RNC regards that UEs are located in weak-coverage areas. In weak-coverage
areas, the wait time-based F2D state transition is not triggered.
The threshold for the number of RLC retransmissions is calculated by using the following
formula:
NOTE
l The BasedTimeF2DThd(BSC6900,BSC6910) parameter specifies the time threshold for the wait time-
based F2D state transition.
l The TimerPoll(BSC6900,BSC6910) parameter specifies the timer for the transmitting side of an AM
RLC entity to wait for a response from the peer end after sending the peer end polling RLC PDUs.
l The BasedTimeF2DRlcRetrNumCoef(BSC6900,BSC6910) parameter specify the factor of the
number of RLC retransmissions for the wait time-based F2D state transition.
If the wait time-based F2D state transition fails, a timer specified by BasedTimeF2DPTAT
(BSC6900,BSC6910) parameter is started. When the timer expires, another wait time-based F2D
state transition is started.
If the UE is browsing web pages, the RNC transfers the UE to the CELL_DCH state. During
the F2D state transition, the RLC data transmission is not suspended for the UE.
NOTE
The RNC considers that the UE is browsing web pages when the following conditions are true:
l The downlink data packets are SYN and ACK packets.
l The source Transmission Control Protocol (TCP) port is 80 or 8080.
Table 3-14 lists the switch parameters related to F2D state transition based on web page
browsing.
Table 3-14 Switch parameters related to F2D state transition based on web page browsing
If the function is turned on, the RNC does not release RAB after the failure of RLC reset but try
to put the UE in CELL_DCH. This can reduce the call drops caused by TRB reset of UEs in
CELL_FACH.
Enabling the F2D State Transition Based on TRB Reset function reduces the high call drop rate
caused by the downlink traffic radio bearer (TRB) reset of UEs in the CELL_FACH state. After
the UE transitions to the CELL_DCH state, the call drop rate is reduced. This function is
controlled by the RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWITCH.
Table 3-15 lists the switch parameters related to F2D state transition based on TRB reset.
Table 3-15 Switch parameters related to F2D state transition based on TRB reset
D2D state transition allows for switchover among channels used for H2D, D2H, E2D, and D2E.
For details, see Table 2-1.
Table 3-16 lists the D2D state transition types and triggering conditions.
E2D l During a RAB setup, RAB is carried over the E-DCH but resources are
insufficient.
l During a RAB setup, RAB is carried over the E-DCH but the coverage is
insufficient. For details, see Radio Bearers Feature Parameter Description.
l After an HSUPA RAB setup, coverage-based fallback from the E-DCH to the
DCH is triggered if the radio coverage is poor during HSUPA data transmission.
For details, see Coverage-based Fallback from the E-DCH to the DCH.
l The E-DCH serving cell (the best cell) has changed and either of the following
conditions is met:
– The new best cell does not support the E-DCH.
– The new best cell has insufficient resources for the E-DCH.
D2E In the preceding E2D scenarios, the RNC switches the UE back to the E-DCH when
any of the following conditions is met:
l For details about periodic attempts to reconfigure to the E-DCH, see description
of technological satisfaction-based inter-frequency DRD in Directed Retry
Decision Feature Parameter Description.
l During DCCC data rate adjustment, the target data rate exceeds the rate bearing
threshold for HSUPA UlBeTraffThsOnHsupa(BSC6900,BSC6910). After an
admission succeeds, D2E state transition is triggered.
l When the uplink coverage recovers, the UE that falls back to the DCH using the
coverage-based fallback from the E-DCH to the DCH algorithm will be switched
back to the E-DCH. For details, see Coverage-based Switchback from DCH to
the E-DCH.
H2D l During a RAB setup, RAB is carried over the HS-DSCH but resources are
insufficient.
l The HS-DSCH serving cell (the best cell) has changed and either of the following
conditions is met:
The new best cell does not support the HS-DSCH.
The new best cell has insufficient resources for the HS-DSCH.
l SRB H2D: if a user is in the weak coverage of a cell and the cell load is light, the
downlink SRB falls back from HS-DSCH to DCH. For details, see HSPA
Evolution Feature Parameter Description.
D2H l In the preceding H2D scenarios, the RNC switches the UE back to the HS-DSCH
when any of the following conditions is met:
For details about periodic attempts to reconfigure to the HS-DSCH, see description
of technological satisfaction-based inter-frequency DRD in Directed Retry
Decision Feature Parameter Description. During DCCC data rate adjustment, the
target data rate exceeds the rate bearing threshold for HSDPA (DlBeTraffTh-
sOnHsdpa). After an admission succeeds, D2H state transition is triggered.
SRB H2D: if a user is in the good coverage of a cell and the cell load is high, the
downlink SRB comes back from DCH to HS-DSCH. For details, see HSPA
Evolution Feature Parameter Description.
The uplink coverage for UEs can be measured in either of the following ways:
If event 6A/6B measurement is used for an E2D switch and a selection of the initial bearer
channel based on Ec/N0, it recommended that periodical P-CPICH RSCP measurement be used
to replace event 6A/6B measurement. Periodical P-CPICH RSCP measurement allows a UE to
perform both a TTI switch and an E2D switch. In this case, the TTI of the UE can be switched
from 2 ms to 10 ms before the UE performs the E2D switch, thereby increasing UE throughput
and improving user experience. If E2D switch-related parameters are set to recommended values,
the number of 2 ms TTI UEs decreases and the number of R99 UEs experiencing weak coverage
on the uplink increases, thereby significantly reducing the HSDPA call drop rate.
During HSUPA BE service data transmission, BE service falls back from the E-DCH to the
DCH when both the following conditions are met:
Threshold of event 6A/6B = Maximum UE transmit power – Relative threshold of event 6A for
BE service
Where
A fallback from E-DCH to DCH occurs only in the current cell, which means the inter-frequency
directed retry decision (DRD) is not performed.
The value of P-CPICH RSCP can be obtained from the intra-frequency MR that is periodically
reported. The reporting period is set by the RabRscpPeriodTimer(BSC6900,BSC6910)
parameter in the SET UCHLQUALITYEVALUATE command.
During HSUPA BE service data transmission, BE service falls back from the E-DCH to the
DCH when the following conditions are met:
l The UE reports the event 4B for all HSUPA BE services.
l The reported value of P-CPICH RSCP is valid.
The calibration value of P-CPICH RSCP that is calculated by using the reported value of P-
CPICH RSCP is smaller than or equal to the value of the BeTTI2msRscpThd
(BSC6900,BSC6910) parameter (2 ms TTI UEs) or BeTTI10msRscpThd
(BSC6900,BSC6910) parameter (10 ms TTI UEs). In this case, other services also falls back
from the E-DCH to the DCH.
The value of RSCP is valid during the period from the time the RNC receives the MR containing
RSCP information to the time specified by the EcN0EffectTime(BSC6910,BSC6900)
parameter.
Calibration value of P-CPICH RSCP = Reported value of P-CPICH RSCP – (CPICH transmit
power of – 33 dBm) – [RTWP – (–105.2 dBm)]
E2DThrou4BThd specifies the threshold of the event 4B.
Fallback from the E-DCH to the DCH occurs in the current cell and does not trigger inter-
frequency DRD.
With the BASE_RSCP_BE_TTI_E2D_RECFG_EFFECT_SWITCH enabled, the algorithm
for coverage-based dynamic TTI adjustment of BE services can take effect even if the switch
for coverage-based fallback from the E-DCH to the DCH (DraSwitch2:
DRA_BASE_COVER_BE_E2D_SWITCH) is enabled. For details about the algorithm for
coverage-based dynamic TTI adjustment of BE services, see HSUPA TTI Selection Feature
Parameter Description.
Calibration value of P-CPICH RSCP = Reported value of P-CPICH RSCP – (CPICH transmit
power of – 33 dBm) – [RTWP – (–105.2 dBm)]
Two new states are introduced in HSPA+: CELL_DCH (CPC) and enhanced CELL_FACH.
l The CELL_DCH (CPC) state (CPC for short) corresponds to the CELL_DCH state, with
continuous packet connectivity (CPC) activated.
l The enhanced CELL_FACH state (EFACH for short) corresponds to the CELL_FACH
state, with enhanced CELL_FACH operation activated.
Compared with CELL_DCH and CELL_FACH states, the following state transitions are
introduces in CPC and EFACH states:
l CPC2F
l CPC2EFACH
l EFACH2CPC
l EFACH2D
l D2EFACH
l F2CPC
For the switch parameters related to CPC and EFACH state transitions, see sections 3.1 D2F
State Transition and 3.9 F2D State Transition.
The state transition procedures from Enhanced CELL_FACH to CELL_PCH in Figure 3-3 are
the same as those from CELL_FACH to CELL_PCH. For details, see section 3.4 F2P State
Transition.
As shown in Figure 3-3, CPC2F, D2EFACH, and CPC2EFACH channel transitions are
triggered by event 4B, which are similar to that for D2F. The only difference is that CPC2F,
D2EFACH, and CPC2EFACH have their own state transition timers, as listed in Table 3-17.
For details about other parameters, see Table 3-1.
F2CPC, EFACH2D, and EFACH2CPC channel transitions are triggered by event 4A, which are
similar to that for F2D. The only difference is that F2CPC, EFACH2D, and EFACH2CPC have
their own event 4A time to trigger and event 4A thresholds, as listed in Table 3-18. For details
about other parameters, see Table 3-10.
Generally, when a smartphone is performing services, data transmission lasts for 1 to 2 seconds,
and the transmission interval is longer than the interval specified by the timer for state transition
from CELL_DCH to CELL_FACH, CELL_PCH, or URA_PCH. This causes the smartphone
to stay in the CELL_DCH state for a long time even when no data is being transmitted, wasting
network resources. Huawei introduced the smart fast state transition function to solve this
problem.
This function enables the smartphone to quickly transit from CELL_DCH to CELL_FACH,
CELL_PCH, or URA_PCH in the preceding situation. Therefore, the time for which the
smartphone with no data transmitted stays in the CELL_DCH state is shortened, increasing
network capacity and CE resource utilization.
Table 3-19 lists the switch parameters related to smart fast state transition.
NOTE
P2F and F2D. In the UTRAN side, P2D is a process where a UE in the CELL_PCH or URA_PCH
state directly transits to the CELL_DCH state. Smart P2D saves bandwidth resources on the
CELL_FACH, eases FACH congestion, and reduces the delay for processing high traffic.
NOTE
When smart P2D is enabled, the RNC records the amount of data a UE transmits during the
interval between when the UE state transits from CELL_PCH or URA_PCH to CELL_FACH
or CELL_DCH and when the UE state transits back to CELL_PCH or URA_PCH.
The RNC records the amount of data transmitted by a UE four consecutive times and predicts
the amount of data the UE will transmit subsequently:
l If the amount of data transmitted by a UE four consecutive times exceeds the value of
TvmThdForSmartP2D(BSC6900,BSC6910), the RNC predicts that the amount of data the
UE will transmit remains above the value of TvmThdForSmartP2D
(BSC6900,BSC6910). When the UE subsequently transmits data in the CELL_PCH or
URA_PCH state, the RNC transits the UE state to CELL_DCH.
l If the amount of data transmitted by a UE four consecutive times is less than or equal to
the value of TvmThdForSmartP2D(BSC6900,BSC6910), the RNC predicts that the UE
has a small amount of data to transmit subsequently. When the UE subsequently transmits
data in the CELL_PCH or URA_PCH state, the RNC transits the UE state to CELL_FACH.
When the policy of preferentially transferring UEs in a cell to the URA_PCH state is used:
l The RNC transfers the UEs to the URA_PCH state by sending CELL UPDATE CONFIRM
messages after the UEs in the cell send CELL UPDATE messages with the cause value
"cell reselection", "periodical cell update", or "re-entered service area."
l The RNC transfers the UEs to the URA_PCH state if the UEs in the cell attempt to transition
from CELL_FACH or CELL_DCH to CELL_PCH or URA_PCH.
Table 3-21 lists the switch parameters related to policy of preferentially transferring UEs in a
cell to the URA_PCH state.
Table 3-21 Switch parameters related to policy of preferentially transferring UEs in a cell to the
URA_PCH state
For details about RLC entity re-establishment triggered by RLC PDU size changes, see 3GPP
TS 25.322.
The following operations can be performed for Huawei RNCs to reduce the RLC SDU discarding
possibility during the state transition:
Service Type T1 T2
Figure 4-1 shows the service connection release procedure when a UE is not transmitting data.
Figure 4-1 Service connection release procedure when a UE is not transmitting data
The service connection release request from the PDCP entity may not be processed in time because the
associated processor in the RNC is busy.
For combined CS and PS services, the access or release of PS services may lead to CS call drops.
When always online is enabled, turning on the switch
PS_INACT_NOTREL_FOR_CSPS_SWITCH under the PROCESSSWITCH3
(BSC6900,BSC6910) parameter can reduce the call drop rate of CS services in combined CS
and PS services. After CS services in combined CS and PS services are released, the remaining
PS service or combined PS and PS services are processed as usual.
When the sum of T1 and T2 is less than the time required for state transition, the UE enters idle
mode without performing state transition.
RNC forbids the state transition for the UE and directly releases the RRC connection with the
UE.
An IMEI consists of 14 decimal digits plus a check digit. It includes 8-digit TAC, 6-digit serial
number (SNR), and 1-digit spare digit.
During a state transition, the UE's RRC connection status on the RAN side is unstable. If the
state transition succeeds, the actual RRC connection status of the UE is consistent with the UE's
RRC connection status stored on the RNC side and the UE continues to complete other
procedures. If the state transition fails, the RNC checks the UE's status and accordingly performs
a state transition or rollback. If RNC does not check the UE's RRC connection status, the actual
RRC connection status of the UE may be inconsistent with the UE's RRC connection status
stored on the RNC side, which will cause a call drop.
This chapter describes the following causes of state transition failures:
l State transition expiry: A D2F or F2D state transition is not complete when the timer
specified by the RbRecfgRspTm timer expires.
l Signaling radio bearer (SRB) reset on the RNC side: The RNC sends a RADIO BEARER
RECONFIGURATION message in acknowledged mode (AM) during an F2D or D2F state
transition, which triggers an SRB reset.
l Radio link (RL) failure: During a D2F state transition on the RNC side, the RNC detects
that the uplink RL is out of synchronization.
the RNC does not need to check whether it has received an RL Fail message from the
NodeBs covering all cells in an active set. You can enable this function of handling D2F
state transition failures by selecting the
D2F_PROCEDURE_OPTIMIZATION_SWITCH check box under the
OptimizationSwitch3 parameter.
If the RCN does not receive an ACK message from a UE, the RNC needs to check whether
it receives an RL Fail message from the NodeBs covering all cells in an active set. If yes,
the RNC considers that the D2F state transition succeeds and transits the UE state to
CELL_FACH on the RNC side. You can enable this function of handling D2F state
transition failures by selecting the
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH check box under the
OptimizationSwitch3 parameter.
When a state transition expires and the RNC does not receive an ACK message from a UE
and an RL Fail message from the NodeBs covering all cells in an active set, the RNC rolls
the UE state back to CELL_DCH on the RNC side. After the rollback to the CELL_DCH
state on the RNC side, the RNC determines whether to automatically establish an RL. You
can enable the automatic RL establishment function by selecting the
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH check box under the
OptimizationSwitch3 parameter.
l Handling a D2F State Transition Failure Caused by an SRB Reset Triggered by a RADIO
BEARER RECONFIGURATION Message
The RNC detects an SRB reset during a D2F state transition, which causes a call drop.
If the SRB reset occurs before the RbRecfgRspTm timer for the D2F state transition expires,
the RNC considers that the D2F state transition succeeds upon receiving an RL Fail message
from the NodeBs covering all cells in an active set, when this timer expires. Then, the RNC
transits the UE state to CELL_FACH on the RNC side. You can enable this function of
handling D2F state transition failures by selecting the
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH check box under the
OptimizationSwitch3 parameter.
If the SRB reset occurs before the RbRecfgRspTm timer expires and the RNC does not
receive an RL Fail message from the NodeBs covering all cells in an active set, the RNC
rolls the UE state back to CELL_DCH on the RNC side when this timer expires. After the
rollback to the CELL_DCH state on the RNC side, the RNC determines whether to
automatically establish an RL. You can enable the automatic RL establishment function
by selecting the D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH check box
under the OptimizationSwitch3 parameter and the
SRB_RESET_RL_SETUP_SWITCH and PS_RL_SETUP_SWITCH check boxes
under the OptimizationSwitch parameter. For the details about call reestablishment of PS
service, see Call Reestablishment Feature Parameter Description.
If the SRB reset occurs after the RbRecfgRspTm timer expires, the RNC determines that
the D2F state transition fails and performs the processing accordingly.
Scenarios in Which a RADIO BEARER RECONFIGURATION Message Is Sent in UM
During a D2F State Transition
A D2F state transition is not complete when the timer specified by the RbRecfgRspTm timer
expires.
Upon receiving an RL Fail message from the NodeBs covering all cells in an active set, the RNC
considers that the D2F state transition succeeds and transits the UE state to the CELL_FACH
state on the RNC side. You can enable this function of handling D2F state transition failures by
NOTE
l RRC, and RB, physical channel relocations are triggered by messages over the Uu interface. For details,
see 3GPP TS 25.331.
l RL reestablishments are triggered by messages over the Iub interface. For details, see 3GPP TS 25.433.
This section describes the solutions used to optimize the overlaps between state transitions and
other procedures, which occur in the live network at a low probability.
7 Engineering Guidelines
If F2P and P2F state transitions are enabled, the UTRAN is able to shift UEs with low data
activity between the CELL_PCH state and the CELL_FACH state. Compared with a UE in idle
mode, a UE in the CELL_PCH state does not have to set up an RRC connection when data needs
to be transmitted. This reduces the amount of signaling over the air interface, lowers the load
on the air interface, and speeds up service setup. Meanwhile, since the UTRAN can learn which
cell the UE is camping on, F2P and P2F state transitions ease congestion on the paging channel.
It is recommended that CELL_PCH state transitions be enabled in the following scenarios:
7.1.3 Deployment
Requirements
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
Data Preparation
None
Activation
Before activating the CELL_PCH state transition, perform the following operations:
l Add a second SCCPCH.
l Modify the Iu-PS activity factor.
l Activate the policy of optimizing FACH parameters.
l Activate the policy of optimizing combined service parameters.
l Activate the policy of optimizing other parameters.
For detailed operations, see section 6.2.3 "Activation" in chapter 6 "Engineering Guidelines" in
Enhanced Fast Dormancy Feature Parameter Description.
NOTE
Activating the preceding policies can reduce the call drop rate but affects experience of users processing
PS services in combined services. For details about how to guarantee experience of users processing PS
services in combined services when the CS services are ongoing, see section 11.1.1 "When to Use Bearer
Channel Type and Access Rate Control Policy for PS BE Services During a Setup of Combined Services"
in Enhanced Combined Services Feature Parameter Description.
A UE can directly enter the CELL_FACH or CELL_DCH state. It can enter the CELL_PCH or
URA_PCH state only through state transition from CELL_FACH or CELL_DCH.
Step 1 (Optional) If the Enhanced Fast Dormancy feature is disabled, it is recommended that you
perform the following operation to activate the state transition for HSDPA and HSUPA services:
Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration:
UMTS Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch modification center:
Modifying RNC Parameters in Batches) and select the
DRA_PS_BE_STATE_TRANS_SWITCH, DRA_HSDPA_STATE_TRANS_SWITCH,
and DRA_HSUPA_STATE_TRANS_SWITCH check boxes under the Dynamic Resource
Allocation Switch parameter.
Step 2 Perform the following operations to enable the CELL_PCH state transition:
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single Run
the RNC MML command SET UUESTATETRANSTIMER (CME single configuration:
UMTS Radio Global Configuration Express > UE State Transition Parameter
Configuration > RNC StateTrans Timer Parameters; CME batch modification center:
Modifying RNC Parameters in Batches). In this step, set BE FACH or E_FACH to PCH
Transition Timer to 5 and Cell Reselection Timer to 180.
2. Run the RNC MML command SET UUESTATETRANS (CME single configuration:
UMTS Radio Global Configuration Express > UE State Transition Parameter
Configuration > UE State Translating Parameters; CME batch modification center:
Modifying RNC Parameters in Batches). In this step, set Cell Reselection Counter
Threshold to 9.
3. Run the RNC MML command SET UUESTATETRANS (CME single configuration:
UMTS Radio Global Configuration Express > PS User Permanent Online Detection Timer;
CME batch modification center: Modifying RNC Parameters in Batches) with both the
Interactive service T1 and Background service T1 parameters set to 1800.
NOTE
This feature involves the parameter settings of state transition from CELL_FACH to CELL_PCH or
URA_PCH. For the parameter settings of other types of state transition, see DCCC Feature Parameter
Description.
For the parameter settings related to fast dormancy, see Enhanced Fast Dormancy Feature Parameter
Description.
----End
Activation Observation
After the state transition from CELL_FACH to CELL_PCH is enabled for a certain period of
time, observe the VS.DCCC.Att.F2P counter. If the VS.DCCC.Att.F2P counter increases, the
state transition from CELL_FACH to CELL_PCH has taken effect.
To check whether UEs enter the CELL_PCH state, you can check the rrc-StateIndicator
information element (IE) in the RB RECFG or PH CH RECFG message.
Deactivation
Run the RNC MML command SET UUESTATETRANSTIMER to set BE FACH or
E_FACH to PCH Transition Timer to 65535.
NOTE
When the BE FACH or E_FACH to PCH Transition Timer is set to 65535, it is regarded that the state
transition from FACH or E_FACH to PCH is not performed
PCHPOWER=-20;
ADD UPCHDYNTFS:CELLID=1, RLCSIZE=240, TRCHID=3, TFSNUMBER=D2, TBNUMBER1=0,
TBNUMBER2=1;
ACT USCCPCH:CELLID=1, PHYCHID=8;
ADD USCCPCHBASIC:CELLID=1, PHYCHID=9, TFCIPRESENCE=EXISTS, SCCPCHOFFSET=70,
SCRAMBCODE=0, STTDIND=FALSE, PO1=8, CTFCSIZE=BIT4, SLOTFORMAT=D8,
MBMSCHIND=COMMON;
ADD USCCPCHTFC:CELLID=1, PHYCHID=9, CTFC=0;
ADD USCCPCHTFC:CELLID=1, PHYCHID=9, CTFC=1;
ADD USCCPCHTFC:CELLID=1, PHYCHID=9, CTFC=2;
ADD USCCPCHTFC:CELLID=1, PHYCHID=9, CTFC=3;
ADD UFACH:CELLID=1, TRCHID=4, PHYCHID=9, TTI=T10, RATEMATCHINGATTR=220,
MAXCMCHPI=D15, MINCMCHPI=D14, SIGRBIND=TRUE, CHCODINGTYPE=CONVOLUTIONAL,
CODINGRATE=D1/2, TOAWS=35, TOAWE=10, MAXFACHPOWER=10;
ADD UFACH:CELLID=1, TRCHID=5, PHYCHID=9, TTI=T10, RATEMATCHINGATTR=130,
MAXCMCHPI=D13, MINCMCHPI=D0, SIGRBIND=FALSE, CHCODINGTYPE=TURBO, TOAWS=35,
TOAWE=10, MAXFACHPOWER=10;
ADD UFACHDYNTFS:CELLID=1, TRCHID=4, RLCSIZE=168, TFSNUMBER=D3, TBNUMBER1=0,
TBNUMBER2=1, TBNUMBER3=2;
ADD UFACHDYNTFS:CELLID=1, TRCHID=5, RLCSIZE=360, TFSNUMBER=D2, TBNUMBER1=0,
TBNUMBER2=1;
ADD UFACHLOCH:TRCHID=4, CELLID=1, SDUDISCARDTIMER=T10, MAXPDUSIZE=20;
ACT USCCPCH:CELLID=1, PHYCHID=9;
ACT UCELL:CELLID=1;
ADD UCTCH: CELLID=1, FachId=4;
ACT UCELLCBS: CELLID=1;
SET UNBMPARA: ReliabilitySwitch=CELL_SIB_NOT_UPD_NCELL_CHG_SWITCH-0;
attempts slightly decreases in poor coverage areas and the number of RRC connection
attempts significantly decreases in good coverage areas. A possible result of this is that
the total RRC connection success rate decreases but the number of RRC connection
failures does not increase.
Check the counters listed in Table 7-2. Generally, the number of RRC connection
requests decreases.
VS.RAB.AbnormRel.PS.F2P)/(VS.RAB.AbnormRel.PSR99 +
VS.RAB.NormRel.PSR99 – VS.RAB.AbnormRel.PS.PCH –
VS.RAB.NormRel.PS.PCH + VS.HSDPA.F2H.Succ + VS.HSDPA.D2H.Succ +
VS.PSR99.D2P.Succ + VS.DCCC.Succ.F2P + VS.DCCC.Succ.F2U)] x 100%
– The HSDPA call drop rate measures the ratio of the number of abnormal HSDPA service
releases to the total number of normal and abnormal HSDPA service releases. Its
calculation formula is changed to the following:
HSDPA Service Drop Ratio with PCH (Cell) = [(VS.HSDPA.RAB.AbnormRel –
VS.HSDPA.RAB.AbnormRel.H2P)/(VS.HSDPA.RAB.AbnormRel +
VS.HSDPA.RAB.NormRel + VS.HSDPA.HHO.H2D.SuccOutIntraFreq +
VS.HSDPA.HHO.H2D.SuccOutInterFreq + VS.HSDPA.H2D.Succ +
VS.HSDPA.H2F.Succ + VS.HSDPA.H2P.Succ)] x 100%
– The HSUPA call drop rate measures the ratio of the number of abnormal HSUPA service
releases to the total number of normal and abnormal HSUPA service releases. Its
calculation formula is changed to the following:
HSUPA Call Drop Ratio with PCH (Cell) = [(VS.HSUPA.RAB.AbnormRel –
VS.HSUPA.RAB.AbnormRel.E2P)/(VS.HSUPA.RAB.AbnormRel +
VS.HSUPA.RAB.NormRel + VS.HSUPA.HHO.E2D.SuccOutIntraFreq +
VS.HSUPA.HHO.E2D.SuccOutInterFreq + VS.HSUPA.E2F.Succ +
VS.HSUPA.E2D.Succ + VS.HSUPA.E2P.Succ)] x 100%
l FACH congestion duration
After this feature is enabled, the number of UEs in the CELL_FACH state increases, and
therefore traffic on the FACH increases. As a result, the duration of FACH congestion may
increase.
l Number of cell reselections
If there are too many cell reselections (VS.AttCellUpdt.Resel), the air interface is easily
congested. To resolve this issue, enable URA_PCH state transitions to reduce CELL
UPDATE messages.
If the D2P, F2P, P2F, F2U, U2F, U2U, or P2U state transition is enabled, the UTRAN allows
the state of low-activity UEs to be transited between CELL_PCH/URA_PCH and CELL_FACH.
In this case, UEs do not need to reestablish RRC connections before transmitting data, thereby
reducing signaling and load over the Uu interface, decreasing service setup delay, and improving
user experience. If the D2P, F2P, P2F, F2U, U2F, U2U or P2U state transition is disabled, UEs
must release RRC connections and enter the idle mode every time they stop transmitting data.
When the UEs have data to transmit, they must reestablish RRC connections.
Enabling F2U, U2F, U2U, and P2U state transitions also reduces the number of cell reselections
and thereby reduces air interface signaling caused by CELL UPDATE messages. It is
recommended that URA_PCH state transitions be enabled in scenarios where cell reselections
generate too many CELL UPDATE messages.
After the URA_PCH state transition is enabled, the paging channel may be congested due to a
dramatic increase in paging messages. In this case, divide the UTRAN registration area (URA)
or enable the Layered Paging in URA_PCH feature.
7.2.3 Deployment
Requirements
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
None
Data Preparation
None
Activation
Before activating the CELL_PCH state transition, perform the following operations:
NOTE
Activating the preceding policies can reduce the call drop rate but affects experience of users processing
PS services in combined services. For details about how to guarantee experience of users processing PS
services in combined services when the CS services are ongoing, see section 11.1.1 "When to Use Bearer
Channel Type and Access Rate Control Policy for PS BE Services During a Setup of Combined Services"
in Enhanced Combined Services Feature Parameter Description.
A UE can directly enter the CELL_FACH or CELL_DCH state. It can enter the CELL_PCH or
URA_PCH state only through state transition from CELL_FACH or CELL_DCH.
Step 1 (Optional) If the Enhanced Fast Dormancy feature is disabled, it is recommended that you
perform the following operation to activate the state transition for HSDPA and HSUPA services:
Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration:
UMTS Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch modification center:
Modifying RNC Parameters in Batches) and select the
DRA_PS_BE_STATE_TRANS_SWITCH, DRA_HSDPA_STATE_TRANS_SWITCH,
and DRA_HSUPA_STATE_TRANS_SWITCH check boxes under the Dynamic Resource
Allocation Switch parameter.
Step 2 To enable the URA_PCH state transition, set parameters related to the state transition from
CELL_FACH to CELL_PCH or URA_PCH as follows:
1. Run the RNC MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Connection_Oriented RRM
Switch Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: Modifying RNC Parameters in Batches) and select the
DRA_PS_BE_STATE_TRANS_SWITCH check box under the Dynamic Resource
Allocation Switch parameter.
2. Run the RNC MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Connection_Oriented RRM
Switch Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: Modifying RNC Parameters in Batches) and select the
DRA_F2U_SWITCH check box under the Dynamic Resource Allocation Switch
parameter to allow the state of UEs to be directly transited from CELL_FACH to
URA_PCH.
3. Run the RNC MML command SET UUESTATETRANSTIMER (CME single
configuration: UMTS Radio Global Configuration Express > UE State Transition
Parameter Configuration > RNC StateTrans Timer Parameters; CME batch modification
center: Modifying RNC Parameters in Batches) and set the BE FACH or E_FACH to
PCH Transition Timer parameter to 5 and keep the default value of the Cell Reselection
Timer parameter.
4. Run the RNC MML command SET UUESTATETRANS (CME single configuration:
UMTS Radio Global Configuration Express > UE State Transition Parameter
Configuration > UE State Translating Parameters; CME batch modification center:
Modifying RNC Parameters in Batches) and keep the default value of the Cell Reselection
Counter Threshold parameter.
NOTE
This document only describes parameter settings for state transition from CELL_FACH to
CELL_PCH or URA_PCH. For the parameter settings of other types of state transition, see DCCC
Feature Parameter Description. For the parameter settings related to fast dormancy, see Enhanced
Fast Dormancy Feature Parameter Description.
----End
Activation Observation
After the state transition from CELL_FACH to URA_PCH is enabled for a certain period of
time, observe the VS.DCCC.Att.F2U and VS.DCCC.Succ.F2U counters. If the values of the
VS.DCCC.Att.F2U and VS.DCCC.Succ.F2U counters increase, the state transition from
CELL_FACH to URA_PCH has taken effect.
Deactivation
Run the RNC MML command SET UUESTATETRANS with the BE FACH or E_FACH to
PCH Transition Timer parameter set to 65535.
NOTE
If the BE FACH or E_FACH to PCH Transition Timer parameter is set to 65535 (maximum value),
the state transition from CELL_FACH or E_FACH to CELL_PCH is prohibited.
l Paging
The RNC pages UEs in the URA_PCH state, within the URA. Enabling URA_PCH state
transitions increases the number of paging messages, compared with when only
CELL_PCH state transitions are enabled. Check the counters listed in Table 7-3 to assess
the effect of URA_PCH state transitions.
After this feature is enabled, a large number of UEs are switched to the CELL_PCH or
URA_PCH state. As a result, the number of paging attempts in idle mode significantly
decreases, but the original paging failures cannot be eliminated. A possible consequence
of this is that the paging success rate in idle mode decreases. The original paging failures
may be caused by the following:
– UEs that are dropped from the network or abnormally shut down
– Poor coverage
– Multiple RNCs sharing the same LAC or RAC
If enabling URA_PCH state transitions significantly increases the value of the counter
VS.RRC.Paging1.Loss.PCHCong.Cell (which means that the paging channel is congested),
enable Layered Paging in URA_PCH.
For details about Layered Paging in URA_PCH, see Layered Paging in URA_PCH Feature
Parameter Description.
VS.HSDPA.HHO.H2D.SuccOutInterFreq + VS.HSDPA.H2D.Succ +
VS.HSDPA.H2F.Succ + VS.HSDPA.H2P.Succ)] x 100%
– The HSUPA call drop rate measures the ratio of the number of abnormal HSUPA service
releases to the total number of normal and abnormal HSUPA service releases. Its
calculation formula is changed to the following:
HSUPA Call Drop Ratio with PCH (Cell) = [(VS.HSUPA.RAB.AbnormRel –
VS.HSUPA.RAB.AbnormRel.E2P)/(VS.HSUPA.RAB.AbnormRel +
VS.HSUPA.RAB.NormRel + VS.HSUPA.HHO.E2D.SuccOutIntraFreq +
VS.HSUPA.HHO.E2D.SuccOutInterFreq + VS.HSUPA.E2F.Succ +
VS.HSUPA.E2D.Succ + VS.HSUPA.E2P.Succ)] x 100%
l FACH congestion duration
After this feature is enabled, the number of UEs in the CELL_FACH state increases, and
therefore traffic on the FACH increases. As a result, the duration of FACH congestion may
increase.
7.3.1 Requirements
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package has been configured before this
feature is activated.
l License
This feature is controlled by the license for the WRFD-010611 HSDPA Enhanced Package
feature. For details about this license, see HSDPA Feature Parameter Description.
7.3.3 Activation
Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration:
UMTS Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch modification center:
Modifying RNC Parameters in Batches). In this step, select the
DRA_HSDPA_STATE_TRANS_SWITCH and
DRA_PS_BE_STATE_TRANS_SWITCH check boxes under the parameter Dynamic
Resource Allocation Switch.
traced data to ensure that the value of the IE rrc-StateIndicator is cell-FACH (1), as shown
in Figure 7-1.
7.3.5 Deactivation
1. Run the RNC MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Connection_Oriented
RRM Switch Configuration > Connection Oriented Algorithm Switches;CME batch
modification center: Modifying RNC Parameters in Batches). In this step, clear the
DRA_HSDPA_STATE_TRANS_SWITCH and
DRA_PS_BE_STATE_TRANS_SWITCH check boxes under the parameter Dynamic
Resource Allocation Switch.
l The penetration rate of UEs that do not send Signaling Connection Release Indication
messages (for example, Nokia phones) is greater than 20%.
l Network load is heavy (with more than 30 HSPA UEs in a cell).
7.4.2 Deployment
Requirements
Before deploying fast state transition, enable the following functions:
Data Preparation
TthdForSFSTUserIden- A large value of this parameter leads to few D2F state Netwo
tify(BSC6900,BSC6910) transitions, which reduces the gain from fast state rk plan
transition. A small value of this parameter may lead to
frequent state transitions between CELL_DCH and
CELL_FACH, which increases the risk of call drops.
The recommended value is 15.
Activation
The following procedure is used to activate fast state transition:
1. Run the following MML commands to enable fast state transition on the RNC LMT:
SET UCORRMALGOSWITCH:
DraSwitch=DRA_SMART_FAST_STATE_TRANS_SWITCH-1;
ADD UCELLDCCC: CellId=01,
DraSwitch=DRA_SMART_FAST_STATE_TRANS_SWITCH-1;
NOTE
SET UCORRMALGOSWITCH is used to set the RNC-level switch for fast state transition.
ADD UCELLDCCC is used to set the cell-level switch for fast state transition.
2. Run the following MML command to set the timer for determining whether a UE is capable
of fast state transition on the RNC LMT:
SET USTATETIMER: TthdForSFSTUserIdentify=15;
3. Run the following MML command to set the inactivity timer for UEs capable of fast state
transition in the CELL_DCH state on the RNC LMT:
SET UPSINACTTIMER: PsInactTmrForFstDrmDch=5;
4. Run the following MML command to set the inactivity timer for UEs capable of fast state
transition in the CELL_FACH state on the RNC LMT:
SET UPSINACTTIMER: PsInactTmrForFstDrmFach=5;
5. Run the following MML command to set the inactivity timer for UEs capable of fast state
transition in the CELL_PCH state on the RNC LMT:
SET UPSINACTTIMER: PsInactTmrForPreFstDrm=1800;
----End
Activation Observation
The following procedure is used to monitor the effect of fast state transition:
If so, fast state transition is functioning properly. If not, fast state transition failed.
----End
Deactivation
Run the following MML commands to deactivate fast state transition on the RNC LMT:
SET UCORRMALGOSWITCH:
DraSwitch=DRA_SMART_FAST_STATE_TRANS_SWITCH-0;
MOD UCELLDCCC:
CellId=01,DraSwitch=DRA_SMART_FAST_STATE_TRANS_SWITCH-0;
NOTE
SET UCORRMALGOSWITCH is used to set the RNC-level switch for fast state transition.
MOD UCELLDCCC is used to change the cell-level switch setting for fast state transition.
ID Counter Description
ID Counter Description
Enabling fast state transition saves DCH resources and therefore affects these counters as
follows:
7.5.2 Deployment
Requirements
Before deploying smart P2D, enable one of the following functions:
Data Preparation
Activation
The following procedure is used to activate smart P2D:
SET UCORRMALGOSWITCH is used to set the RNC-level switch for smart P2D.
ADD UCELLDCCC is used to set the cell-level switch for smart P2D.
2. Run the following MML command to set the throughput threshold for P2D state transition
on the RNC LMT:
SET UUESTATETRANS: TvmThdForSmartP2D= 51;
----End
Activation Observation
The following procedure is used to monitor the effect of smart P2D:
Step 1 Use a UE to start UE throughput monitoring and UE tracing on the RNC side. Obtain the UE
IMSI.
Step 2 When the UE state transits to CELL_PCH or URA_PCH, use the UE to set up a service with
the traffic volume greater than the value of TvmThdForSmartP2D(BSC6900,BSC6910), such
as, FTP download. After the service is complete, wait for the UE to transit to the CELL_PCH
or URA_PCH state.
Step 4 Wait until the UE state transits to CELL_PCH or URA_PCH and set up a service again. Check
the UE tracing results to observe whether the UE state directly transits from CELL_PCH or
URA_PCH to CELL_DCH.
----End
Deactivation
Run the following MML commands to deactivate smart P2D on the RNC LMT:
NOTE
SET UCORRMALGOSWITCH is used to set the RNC-level switch for smart P2D.
MOD UCELLDCCC is used to change the cell-level switch setting for smart P2D.
ID Counter Description
Enabling smart P2D relieves FACH congestion and therefore affects these counters as follows:
7.6.2 Deployment
Requirements
When enabling the function of handling state transition failures, you need to set switches for the
following functions to on:
Data Preparation
Table 7-10 Parameters related to the function of handling state transition failures
Activation
Run the RNC MML command SET URRCTRLSWITCH and set parameters for different state
transitions as follows:
l For the D2F state transition during which a RADIO BEARER RECONFIGURATION
message is sent in UM, select the D2F_PROCEDURE_OPTIMIZATION_SWITCH
check box under the Optimization Switch3 parameter.
l For the F2D state transition during which a RADIO BEARER RECONFIGURATION
message is sent in UM, select the F2D_PROCEDURE_OPTIMIZATION_SWITCH
check box under the Optimization Switch3 parameter.
l For the D2F state transition during which a RADIO BEARER RECONFIGURATION
message is sent in AM, select the D2F_PROCEDURE_OPTIMIZATION_SWITCH,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH and
AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH check boxes under the
Optimization Switch3 parameter.
l For the F2D state transition during which a RADIO BEARER RECONFIGURATION
message is sent in AM, select the F2D_PROCEDURE_OPTIMIZATION_SWITCH
and AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH check boxes under the
Optimization Switch3 parameter.
NOTE
When you want to enable the function of handling D2F state transition failures, it is recommended that the
following check boxes under the OptimizationSwitch parameter in the SET URRCTRLSWITCH
command also be selected to enable the automatic RL establishment function based on the SRB reset
triggered by the MEASUREMENT CONTROL message:
l MC_RL_RESET_SWITCH
l SRB_RESET_RL_SETUP_SWITCH
l PS_RL_SETUP_SWITCH
Activation Observation
For details, see sections 7.6.1 When to Use the Function of Handling State Transition
Failures and 7.6.3 Performance Monitoring.
Deactivation
Run the RNC MML command SET URRCTRLSWITCH and set parameters for different state
transitions as follows:
l To deactivate the function of handling failures in D2F state transitions during which a
RADIO BEARER RECONFIGURATION message is sent in UM, clear the
D2F_PROCEDURE_OPTIMIZATION_SWITCH check box under the Optimization
Switch3 parameter.
l To deactivate the function of handling failures in F2D state transitions during which a
RADIO BEARER RECONFIGURATION message is sent in UM, clear the
F2D_PROCEDURE_OPTIMIZATION_SWITCH check box under the Optimization
Switch3 parameter.
l To deactivate the function of handling failures in D2F state transitions during which a
RADIO BEARER RECONFIGURATION message is sent in AM, clear the
D2F_PROCEDURE_OPTIMIZATION_SWITCH,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH and
AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH check boxes under the
Optimization Switch3 parameter.
l To deactivate the function of handling failures in F2D state transitions during which a
RADIO BEARER RECONFIGURATION message is sent in AM, clear the
F2D_PROCEDURE_OPTIMIZATION_SWITCH and
AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH check boxes under the
Optimization Switch3 parameter.
//Disabling the function of handling a failure in the D2F state transition during
which a RADIO BEARER RECONFIGURATION message is sent in AM
SET URRCTRLSWITCH:
OptimizationSwitch3=D2F_PROCEDURE_OPTIMIZATION_SWITCH-0&D2F_AM_PROCEDURE_OPTIMIZAT
ION_SWITCH-0&AM_D2F_F2D_ResTmr_OPTIMIZATION_SWITCH-0;
//Disabling the function of handling a failure in the F2D state transition during
which a RADIO BEARER RECONFIGURATION message is sent in AM
SET URRCTRLSWITCH:
OptimizationSwitch3=F2D_PROCEDURE_OPTIMIZATION_SWITCH-0&AM_D2F_F2D_ResTmr_OPTIMIZA
TION_SWITCH-0;
The function of handling F2D and D2F state transition failures can reduce call drops, thereby
reducing call drop ratios (including HSDPA call drop ratio and HSUPA call drop ratio).
PS call drop ratio (cell) = [VS.RAB.AbnormRel.PS/(VS.RAB.AbnormRel.PS +
VS.RAB.NormRel.PS)] x 100%
PS call drop ratio with PCH (cell) = [(VS.RAB.AbnormRel.PS – VS.RAB.AbnormRel.PS.PCH
– VS.RAB.AbnormRel.PS.D2P – VS.RAB.AbnormRel.PS.F2P)/(VS.RAB.AbnormRel.PS +
VS.RAB.NormRel.PS – VS.RAB.AbnormRel.PS.PCH – VS.RAB.NormRel.PS.PCH +
VS.DCCC.D2P.Succ + VS.DCCC.Succ.F2P)] x 100%
HSDPA call drop ratio (cell) = [(VS.HSDPA.RAB.AbnormRel)/(VS.HSDPA.RAB.AbnormRel
+ VS.HSDPA.RAB.NormRel + VS.HSDPA.H2D.Succ + VS.HSDPA.H2F.Succ +
VS.HSDPA.HHO.H2D.SuccOutIntraFreq + VS.HSDPA.HHO.H2D.SuccOutInterFreq)] x
100%
HSDPA service drop ratio with PCH (cell) = [(VS.HSDPA.RAB.AbnormRel –
VS.HSDPA.RAB.AbnormRel.H2P)/VS.HSDPA.RAB.AbnormRel +
VS.HSDPA.RAB.NormRel + VS.HSDPA.HHO.H2D.SuccOutIntraFreq +
VS.HSDPA.HHO.H2D.SuccOutInterFreq + VS.HSDPA.H2D.Succ + VS.HSDPA.H2F.Succ +
VS.HSDPA.H2P.Succ)] x 100%
When call reestablishment is triggered by handling a state transition failure, the value of the
VS.AttRlReEst.PS counter increases.
When the function of handling failures in state transitions during which RADIO BEARER
RECONFIGURATION messages are sent in AM is enabled, the value of the
VS.RAB.AbnormRel.PS.RF.SRBReset counter decreases.
After the function of handling D2F state transition failures takes effect, call drops may still occur
after state transitions. These call drops are considered as occurring on the common channel
instead of occurring on the DCH, which increases the value of the VS.RAB.AbnormRel.PS.CCH
counter. This counter indicates the call drop rate on the common channel.
If a U2F state transition fails due to an overlap between a U2F state transition and a cell update
triggered by cause value other than those triggering the U2F state transition in the live network,
it is recommended that the function of optimizing overlaps between U2F and cell updates
triggered by cause values other than triggering U2F be enabled.
7.7.2 Deployment
Requirements
When enabling the function of optimizing the overlap between state transition and CS service
setup or the function of optimizing overlaps between U2F and cell updates triggered by cause
values other than those triggering U2F, you need to set switches for the following functions to
on:
Data Preparation
Table 7-11 Parameters related to the function of optimizing the overlap between a state transition
and CS service setup or cell update
Activation
l To enable the function of optimizing the overlap between D2F and CS service setup, run
the RNC MML command SET UCORRMALGOSWITCH. In this step, select the
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH check box under the Dynamic
Resource Allocation Switch 2 parameter.
l To enable the function of optimizing the overlap between F2P and CS service setup, run
the RNC MML command SET UCORRMPARA. In this step, select the
PERFENH_F2P_LIMIT_WITH_CS_IU_CON_SWITCH check box under the
Performance Enhancement Switch 1 parameter.
l To enable the function of optimizing overlaps between U2F and cell updates, run the RNC
MML command SET URRCTRLSWITCH. In this step, select the
URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH check box under the
Optimization Switch4 parameter.
Activation Observation
For details, see sections 7.7.1 When to Use the Function of Optimizing Overlaps Between
State Transitions and Other Procedures and 7.7.3 Performance Monitoring.
Deactivation
l To disable the function of optimizing the overlap between D2F and CS service setup, run
the RNC MML command SET UCORRMALGOSWITCH. In this step, clear the
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH check box under the Dynamic
Resource Allocation Switch 2 parameter.
l To disable the function of optimizing the overlap between F2P and CS service setup, run
the RNC MML command SET UCORRMPARA. In this step, clear the
PERFENH_F2P_LIMIT_WITH_CS_IU_CON_SWITCH check box under the
Performance Enhancement Switch 1 parameter.
l To disable the function of optimizing overlaps between U2F and cell updates, run the RNC
MML command SET URRCTRLSWITCH. In this step, clear the
URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH check box under the
Optimization Switch4 parameter.
The function of optimizing overlaps between state transitions and other procedures can provide
the following benefits:
8 Parameters
Coverag turned off, the RNC does not allow UEs to perform
e blind-handover-based DRDs. 8.
Inter- PERFENH_MCDRD_MEAS_OPT_SWITCH:
RAT Whether to enable the optimized inter-frequency
Handov measurement control function in the measurement-
er Based based DRD. When this switch is turned on, the RNC
on filters out inter-frequency neighboring cells that do not
Coverag meet the requirements for periodic retry according to the
e HSPA+ and SPG priorities during the delivery of
measurement control messages. When this switch is
AMR/ turned off, the RNC does not filter out inter-frequency
WB- neighboring cells that do not meet the requirements. 9.
AMR PERFENH_UE_LOC_DRD_OPT_SWITCH:
Speech Whether the RNC filters DRD cells in high frequency
Rates bands if the current cell is in a low frequency band and
Control the RSCP value cannot be measured or cannot be
obtained through measurements or it expires the validity
of measurement reports when the location-based
multiband DRD algorithm is enabled. When this switch
is turned off, the RNC filters out all DRD cells in high
frequency bands. When this switch is turned on, the
RNC does not filter DRD cells in high frequency bands.
10. PERFENH_PS_FAST_RETURN_LTE_SWITCH:
Whether the RNC releases the RRC connection when a
CS fallback UE keeps a PS connection after terminating
a call. When this switch is turned on, the RNC releases
the RRC connection by sending to a UE an RRC
CONNECTION RELEASE message that carries the
information about LTE frequencies if the UE keeps the
PS connection after terminating the CS service. When
this switch is turned off, the RNC does not release the
RRC connection if a CS fallback UE keeps the PS
connection after terminating the CS service. 11.
PERFENH_FORCE_AMR_INTER_RAT_OUT_SWI
TCH: Whether to reject access of any CS services to the
UMTS network. When this switch is turned off, CS
services normally access the UMTS network. When this
switch is turned on, the RNC performs inter-RAT DRDs
to transfer the narrowband AMR services assigned by
the CN through the CS domain to the current best cell's
neighboring GSM cells for blind handovers. If the CN
assigns other services through the CS domain, the RNC
directly rejects such services. 12.
PERFENH_INACTIVE_F2P_SWITCH: Whether the
UE inactivity-based F2P state transition algorithm takes
effect. F2P transition is short for the transition from
CELL_FACH to CELL_PCH or URA_PCH. If the
PERFENH_MR_AGPS_CMP_SWITCH,
PERFENH_AMRC_NACK_SWITCH,
PERFENH_MCDRD_OPT_SWITCH,
PERFENH_MCDRD_MEAS_OPT_SWITCH,
PERFENH_UE_LOC_DRD_OPT_SWITCH,
PERFENH_PS_FAST_RETURN_LTE_SWITCH,
PERFENH_FORCE_AMR_INTER_RAT_OUT_SWI
TCH, PERFENH_INACTIVE_F2P_SWITCH,
PERFENH_NB_AMRC_UL_RATESET_EXT_SWIT
CH,
PERFENH_DC_USERNUM_LDB_OPT_SWITCH,
PERFENH_DCH_TRCH_OPT_SWITCH,
PERFENH_RB_MAPPING_OPT_SWITCH,
PERFENH_U2L_REDIR_WITH_BLACK_CELL_S
WITCH,
PERFENH_UL_RL_FAIL_SRV_CELL_CHG_SWIT
CH, PERFENH_HO_SIGNAL_SCENE_CTRL,
PERFENH_PS_CMTIMEOUT_UP_LIMIT_SWITC
H,
PERFENH_SPEC_PRD_HHO_DELAY_TIME_SWI
TCH,
PERFENH_BASE_COV_BE_E2D_10MS_OFF_SWI
TCH,
PERFENH_RRC_CELL_HSUPA_CAP_CHG_SWIT
CH,
PERFENH_RRC_CELL_HSDPA_CAP_CHG_SWIT
CH,
PERFENH_CELL_TTI2MS_CAP_CHG_OPT_SWIT
CH, PERFENH_OLPC_TBSIZE0_CMP_SWITCH,
PERFENH_UU_P2D_F2D_MSG_OPT_SWITCH,
PERFENH_DYC_INIBITRATE_MULTI_SWITCH,
PERFENH_RLRESETUP_GUARANTEE_SWITCH,
PERFENH_RLRESETUP_PREEMPT_SWITCH
Default Value:
PERFENH_COMM_PLMN_HO_ALLOWED_SWIT
CH:
0,PERFENH_INITIAL_NCELLDETECT_SWITCH:
0,PERFENH_VP_TO_AMR_SWITCH:
1,PERFENH_AMRC_TFI_CMP_SWITCH:
0,PERFENH_MR_AGPS_CMP_SWITCH:
0,PERFENH_AMRC_NACK_SWITCH:
0,PERFENH_MCDRD_OPT_SWITCH:
0,PERFENH_MCDRD_MEAS_OPT_SWITCH:
1,PERFENH_UE_LOC_DRD_OPT_SWITCH:
1,PERFENH_PS_FAST_RETURN_LTE_SWITCH:
0,PERFENH_FORCE_AMR_INTER_RAT_OUT_S
rate set A and the rate set includes other rates, except
SID rate and 0 bit/s rate, the extended rate set is
determined in the following ways: If rate set A contains
less than or equal to four types of rates, rate set A is
considered as the extended rate set. If rate set A contains
more than four types of rates, the intersection between
the rate set A and the five types of rates (4.75 kbit/s, 5.9
kbit/s, 7.4 kbit/s, 7.95kbit/s, and 12.2 kbit/s) is
considered as rate set B. In this situation, if the rate set
B contains less than or equal to four types of rates, rate
set B is considered as the extended rate set. If rate set B
contains more than four types of rates, the extended rate
set is generated after the rate 7.95 kbit/s is deleted from
rate set B. 14.
PERFENH_DC_USERNUM_LDB_OPT_SWITCH:
Whether non-flexible DC cells are ranked based on the
user number of a single cell during the load balancing.
When this switch is turned off, non-flexible DC cells
are ranked based on the user number of the carrier group
during the load balancing. When this switch is turned
on, non-flexible DC cells are ranked based on the user
number of a single cell during the load balancing. 15.
PERFENH_DCH_TRCH_OPT_SWITCH: Whether
the RNC changes the contents of the information
elements (IEs) "UL-AddReconfTransChInformation"
and "rb-MappingInfo" in the RRC RB SETUP and RRC
RB RECFG messages. When the content of the sub-IE
"tfs-SignallingMode" in the IE "DL-AddReconfTran-
sChInformation" is the same as that of the sub-IE
"transportFormatSet" in the IE "UL-AddReconfTran-
sChInformation", the sub-IE "tfs-SignallingMode" can
be defined as "SameAsULTrCH", which reduces the
sizes of the RRC RB SETUP and RRC RB RECFG
messages. When this switch is turned off, the RNC
defines the IE "LogicalChannelList" as "Configured"
and the IE "rlc-Size-List" as "allSizes". When this
switch is turned on, the RNC defines the IE
"LogicalChannelList" as "allSizes" and the sub-IE "rlc-
Size-List" in the IE "rb-MappingInfo" as "Configured".
The uplink TFS is the same as the downlink TFS. 16.
PERFENH_RB_MAPPING_OPT_SWITCH: Whether
the RRC RB SETUP message contains the information
element (IE) "RB mapping info" if the transport channel
and rate of a signaling radio bearer (SRB) remain
unchanged. If the RRC SETUP REQ message has
contained the IE "RB mapping info", the RRC RB
SETUP message does not need to contain the IE, which
PERFENH_DCH_TRCH_OPT_SWITCH,
PERFENH_RB_MAPPING_OPT_SWITCH,
PERFENH_U2L_REDIR_WITH_BLACK_CELL_S
WITCH,
PERFENH_UL_RL_FAIL_SRV_CELL_CHG_SWIT
CH, PERFENH_HO_SIGNAL_SCENE_CTRL,
PERFENH_PS_CMTIMEOUT_UP_LIMIT_SWITC
H,
PERFENH_SPEC_PRD_HHO_DELAY_TIME_SWI
TCH,
PERFENH_BASE_COV_BE_E2D_10MS_OFF_SWI
TCH,
PERFENH_RRC_CELL_HSUPA_CAP_CHG_SWIT
CH,
PERFENH_RRC_CELL_HSDPA_CAP_CHG_SWIT
CH,
PERFENH_CELL_TTI2MS_CAP_CHG_OPT_SWIT
CH, PERFENH_OLPC_TBSIZE0_CMP_SWITCH,
PERFENH_UU_P2D_F2D_MSG_OPT_SWITCH,
PERFENH_DYC_INIBITRATE_MULTI_SWITCH,
PERFENH_RLRESETUP_GUARANTEE_SWITCH,
PERFENH_RLRESETUP_PREEMPT_SWITCH
Unit: None
Actual Value Range:
PERFENH_COMM_PLMN_HO_ALLOWED_SWIT
CH,
PERFENH_INITIAL_NCELLDETECT_SWITCH,
PERFENH_VP_TO_AMR_SWITCH,
PERFENH_AMRC_TFI_CMP_SWITCH,
PERFENH_MR_AGPS_CMP_SWITCH,
PERFENH_AMRC_NACK_SWITCH,
PERFENH_MCDRD_OPT_SWITCH,
PERFENH_MCDRD_MEAS_OPT_SWITCH,
PERFENH_UE_LOC_DRD_OPT_SWITCH,
PERFENH_PS_FAST_RETURN_LTE_SWITCH,
PERFENH_FORCE_AMR_INTER_RAT_OUT_SWI
TCH, PERFENH_INACTIVE_F2P_SWITCH,
PERFENH_NB_AMRC_UL_RATESET_EXT_SWIT
CH,
PERFENH_DC_USERNUM_LDB_OPT_SWITCH,
PERFENH_DCH_TRCH_OPT_SWITCH,
PERFENH_RB_MAPPING_OPT_SWITCH,
PERFENH_U2L_REDIR_WITH_BLACK_CELL_S
WITCH,
PERFENH_UL_RL_FAIL_SRV_CELL_CHG_SWIT
CH, PERFENH_HO_SIGNAL_SCENE_CTRL,
PERFENH_PS_CMTIMEOUT_UP_LIMIT_SWITC
H,
PERFENH_SPEC_PRD_HHO_DELAY_TIME_SWI
TCH,
PERFENH_BASE_COV_BE_E2D_10MS_OFF_SWI
TCH,
PERFENH_RRC_CELL_HSUPA_CAP_CHG_SWIT
CH,
PERFENH_RRC_CELL_HSDPA_CAP_CHG_SWIT
CH,
PERFENH_CELL_TTI2MS_CAP_CHG_OPT_SWIT
CH, PERFENH_OLPC_TBSIZE0_CMP_SWITCH,
PERFENH_UU_P2D_F2D_MSG_OPT_SWITCH,
PERFENH_DYC_INIBITRATE_MULTI_SWITCH,
PERFENH_RLRESETUP_GUARANTEE_SWITCH,
PERFENH_RLRESETUP_PREEMPT_SWITCH
Default Value:
PERFENH_COMM_PLMN_HO_ALLOWED_SWIT
CH:
0,PERFENH_INITIAL_NCELLDETECT_SWITCH:
0,PERFENH_VP_TO_AMR_SWITCH:
1,PERFENH_AMRC_TFI_CMP_SWITCH:
0,PERFENH_MR_AGPS_CMP_SWITCH:
0,PERFENH_AMRC_NACK_SWITCH:
0,PERFENH_MCDRD_OPT_SWITCH:
0,PERFENH_MCDRD_MEAS_OPT_SWITCH:
1,PERFENH_UE_LOC_DRD_OPT_SWITCH:
1,PERFENH_PS_FAST_RETURN_LTE_SWITCH:
0,PERFENH_FORCE_AMR_INTER_RAT_OUT_S
WITCH:0,PERFENH_INACTIVE_F2P_SWITCH:
0,PERFENH_NB_AMRC_UL_RATESET_EXT_SW
ITCH:
0,PERFENH_DC_USERNUM_LDB_OPT_SWITCH
:0,PERFENH_DCH_TRCH_OPT_SWITCH:
0,PERFENH_RB_MAPPING_OPT_SWITCH:
0,PERFENH_U2L_REDIR_WITH_BLACK_CELL_
SWITCH:
1,PERFENH_UL_RL_FAIL_SRV_CELL_CHG_SWI
TCH:0,PERFENH_HO_SIGNAL_SCENE_CTRL:
0,PERFENH_PS_CMTIMEOUT_UP_LIMIT_SWIT
CH:
0,PERFENH_SPEC_PRD_HHO_DELAY_TIME_S
WITCH:
0,PERFENH_BASE_COV_BE_E2D_10MS_OFF_S
WITCH:
0,PERFENH_RRC_CELL_HSUPA_CAP_CHG_SWI
InactF2 BSC690 SET WRFD- UE State Meaning: Timer for the UE inactivity-based F2P state
PStateTr 0 UUEST 010202 in transition. If the RNC detects that all uplink and
ansTime ATETR Connect downlink services of the UE in the CELL_FACH state
r ANSTI ed Mode have no data to transmit within the period specified by
MER (CELL- the timer, it triggers the F2P state transition.
DCH, GUI Value Range: 1~64800
CELL-
PCH, Unit: s
URA- Actual Value Range: 1~64800
PCH, Default Value: 10
CELL-
FACH)
InactF2 BSC691 SET WRFD- UE State Meaning: Timer for the UE inactivity-based F2P state
PStateTr 0 UUEST 010202 in transition. If the RNC detects that all uplink and
ansTime ATETR Connect downlink services of the UE in the CELL_FACH state
r ANSTI ed Mode have no data to transmit within the period specified by
MER (CELL- the timer, it triggers the F2P state transition.
DCH, GUI Value Range: 1~64800
CELL-
PCH, Unit: s
URA- Actual Value Range: 1~64800
PCH, Default Value: 10
CELL-
FACH)
BeAbno BSC690 ADD WRFD- HSDPA Meaning: Whether the algorithm for the CELL_DCH to
mH2FS 0 UCELL 0106111 State CELL_FACH state transition takes effect when the air
witch DCCC 1 Transiti interface is abnormal. When the switch is turned on and
MOD on the BE service over HSDPA has low throughput but
UCELL high traffic volume, the RNC triggers the CELL_DCH
DCCC to CELL_FACH state transition, which saves network
resources. When the switch is turned off, no operation
is performed.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF
BeAbno BSC691 ADD WRFD- HSDPA Meaning: Whether the algorithm for the CELL_DCH to
mH2FS 0 UCELL 0106111 State CELL_FACH state transition takes effect when the air
witch DCCC 1 Transiti interface is abnormal. When the switch is turned on and
MOD on the BE service over HSDPA has low throughput but
UCELL high traffic volume, the RNC triggers the CELL_DCH
DCCC to CELL_FACH state transition, which saves network
resources. When the switch is turned off, no operation
is performed.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF
DlBeAb BSC690 SET WRFD- HSDPA Meaning: High traffic indication threshold for BE
nH2FHI 0 UUEST 0106111 State services used in the abnormal air interface-based H2F
ghTvmT ATETR 1 Transiti transition. When the BE service traffic is higher than
hd ANS on this threshold, the BE service traffic is considered to be
high.
GUI Value Range: 1~65535
Unit: 10byte
Actual Value Range: 10~655350
Default Value: 102
DlBeAb BSC691 SET WRFD- HSDPA Meaning: High traffic indication threshold for BE
nH2FHI 0 UUEST 0106111 State services used in the abnormal air interface-based H2F
ghTvmT ATETR 1 Transiti transition. When the BE service traffic is higher than
hd ANS on this threshold, the BE service traffic is considered to be
high.
GUI Value Range: 1~65535
Unit: 10byte
Actual Value Range: 10~655350
Default Value: 102
DlBeAb BSC690 SET WRFD- HSDPA Meaning: Low throughput indication threshold for BE
nH2FLo 0 UUEST 0106111 State services used in the abnormal air interface-based H2F
wThrou ATETR 1 Transiti transition. When the throughput for BE services is not
Thd ANS on greater than this threshold, the BE services have low
throughput.
GUI Value Range: 1~32
Unit: kbit/s
Actual Value Range: 1~32
Default Value: 8
DlBeAb BSC691 SET WRFD- HSDPA Meaning: Low throughput indication threshold for BE
nH2FLo 0 UUEST 0106111 State services used in the abnormal air interface-based H2F
wThrou ATETR 1 Transiti transition. When the throughput for BE services is not
Thd ANS on greater than this threshold, the BE services have low
throughput.
GUI Value Range: 1~32
Unit: kbit/s
Actual Value Range: 1~32
Default Value: 8
BeAbno BSC690 SET WRFD- HSDPA Meaning: Timer for CELL_DCH to CELL_FACH state
rmH2FS 0 UUEST 0106111 State transition when the air interface is abnormal. When the
tateTran ATETR 1 Transiti air interface is abnormal, this timer is started. When this
sTimer ANSTI on timer expires, the state transition is triggered.
MER GUI Value Range: 1~65535
Unit: 0.1s
Actual Value Range: 0.1~6553.5
Default Value: 31
BeAbno BSC691 SET WRFD- HSDPA Meaning: Timer for CELL_DCH to CELL_FACH state
rmH2FS 0 UUEST 0106111 State transition when the air interface is abnormal. When the
tateTran ATETR 1 Transiti air interface is abnormal, this timer is started. When this
sTimer ANSTI on timer expires, the state transition is triggered.
MER GUI Value Range: 1~65535
Unit: 0.1s
Actual Value Range: 0.1~6553.5
Default Value: 31
AbnH2F BSC690 SET WRFD- HSDPA Meaning: Time for prohibiting the CELL_FACH to
Penalty 0 UUEST 0106111 State CELL_DCH state transition on users experiencing the
Len ATETR 1 Transiti H2F state transition when the air interface is abnormal.
ANS on After the H2F state transition is triggered due to the
abnormal air interface, the F2D state transition can be
triggered only after the timer expires, preventing ping-
pong state transitions.
GUI Value Range: 1~65535
Unit: s
Actual Value Range: 1~65535
Default Value: 60
AbnH2F BSC691 SET WRFD- HSDPA Meaning: Time for prohibiting the CELL_FACH to
Penalty 0 UUEST 0106111 State CELL_DCH state transition on users experiencing the
Len ATETR 1 Transiti H2F state transition when the air interface is abnormal.
ANS on After the H2F state transition is triggered due to the
abnormal air interface, the F2D state transition can be
triggered only after the timer expires, preventing ping-
pong state transitions.
GUI Value Range: 1~65535
Unit: s
Actual Value Range: 1~65535
Default Value: 60
DraSwit BSC690 SET WRFD- Dynami Meaning: Dynamic resource allocation switch group. 1.
ch 0 UCORR 021101 c DRA_AQM_SWITCH: When the switch is on, the
MALG WRFD- Channel active queue management algorithm is used for the
OSWIT 0106140 Configu RNC. 2.
CH 3 ration DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITC
Control H: When the switch is on, the TTI dynamic adjustment
WRFD- (DCCC) algorithm for admission CE-based BE services applies
050405 to the UE with the UL enhanced L2 feature. This
HSUPA
WRFD- parameter is valid when
2ms TTI
0106140 DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH
4 Overboo (DraSwitch) is set to ON. 3.
king on DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH
WRFD-
ATM : When the switch is on, the TTI dynamic adjustment
050408
Transmi algorithm is supported for admission CE-based BE
WRFD- ssion services. 4.
010690
HSUPA DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH:
WRFD- 2ms/ When the switch is on, the TTI dynamic adjustment
010202 10ms algorithm for coverage-based BE services applies to the
WRFD- TTI UE with the UL enhanced L2 feature. This parameter is
010612 Handov valid when
er DRA_BASE_COVER_BE_TTI_RECFG_SWITCH
WRFD-
(DraSwitch) is set to ON. 5.
011502 Overboo
DRA_BASE_COVER_BE_TTI_RECFG_SWITCH:
WRFD- king on
When the switch is on, the TTI dynamic adjustment
010636 IP
algorithm is supported for coverage-based BE services.
Transmi
WRFD- 6. DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH:
ssion
0106101 When the switch is on, the TTI dynamic adjustment
0 TTI algorithm for differentiation-based BE services applies
Switch to the UE with the UL enhanced L2 feature. This
WRFD-
for BE parameter is valid when
0106111
Services DRA_BASE_RES_BE_TTI_RECFG_SWITCH
1
Based (DraSwitch) is set to ON. 7.
WRFD- on DRA_BASE_RES_BE_TTI_RECFG_SWITCH:
0106120 Coverag When the switch is on, the TTI dynamic adjustment
8 e algorithm is supported for differentiation-based BE
UE State services. 8. DRA_DCCC_SWITCH: When the switch
in is on, the dynamic channel reconfiguration control
Connect algorithm is used for the RNC. 9.
ed Mode DRA_HSDPA_DL_FLOW_CONTROL_SWITCH:
(CELL- When the switch is on, flow control is enabled for
DCH, HSDPA services in AM mode. 10.
CELL- DRA_HSDPA_STATE_TRANS_SWITCH: When the
PCH, switch is on, the status of the UE RRC that carrying
URA- HSDPA services can be changed to CELL_FACH at the
PCH, RNC. If a PS BE service is carried over the HS-DSCH,
CELL- the switch PS_BE_STATE_TRANS_SWITCH should
FACH) be on simultaneously. If a PS real-time service is carried
DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH,
DRA_BASE_RES_BE_TTI_RECFG_SWITCH,
DRA_DCCC_SWITCH,
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH,
DRA_HSDPA_STATE_TRANS_SWITCH,
DRA_HSUPA_DCCC_SWITCH,
DRA_HSUPA_STATE_TRANS_SWITCH,
DRA_IP_SERVICE_QOS_SWITCH,
DRA_PS_BE_STATE_TRANS_SWITCH,
DRA_PS_NON_BE_STATE_TRANS_SWITCH,
DRA_R99_DL_FLOW_CONTROL_SWITCH,
DRA_THROUGHPUT_DCCC_SWITCH,
DRA_VOICE_SAVE_CE_SWITCH,
DRA_VOICE_TTI_RECFG_SWITCH,
DRA_CSPS_NO_PERIOD_RETRY_SWITCH,
DRA_SMART_FAST_STATE_TRANS_SWITCH,
DRA_PCH_UE_SMART_P2D_SWITCH,
DRA_BASE_RES_BE_TTI_INIT_SEL_SWITCH,
DRA_BASE_COVER_BE_TTI_INIT_SEL_SWITC
H, DRA_F2U_SWITCH,
DRA_BASE_LOAD_HBD_INIT_SEL_SWITCH
Default Value: DRA_AQM_SWITCH:0,
DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITC
H:0,
DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH
:1,
DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH:
0,
DRA_BASE_COVER_BE_TTI_RECFG_SWITCH:
0, DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH:0,
DRA_BASE_RES_BE_TTI_RECFG_SWITCH:1,
DRA_DCCC_SWITCH:1,
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH:0,
DRA_HSDPA_STATE_TRANS_SWITCH:0,
DRA_HSUPA_DCCC_SWITCH:1,
DRA_HSUPA_STATE_TRANS_SWITCH:0,
DRA_IP_SERVICE_QOS_SWITCH:0,
DRA_PS_BE_STATE_TRANS_SWITCH:1,
DRA_PS_NON_BE_STATE_TRANS_SWITCH:0,
DRA_R99_DL_FLOW_CONTROL_SWITCH:0,
DRA_THROUGHPUT_DCCC_SWITCH:0,
DRA_VOICE_SAVE_CE_SWITCH:0,
DRA_VOICE_TTI_RECFG_SWITCH:0,
DRA_CSPS_NO_PERIOD_RETRY_SWITCH:0,
DRA_SMART_FAST_STATE_TRANS_SWITCH:0,
DRA_PCH_UE_SMART_P2D_SWITCH:0,
DraSwit BSC691 SET WRFD- Dynami Meaning: Dynamic resource allocation switch group. 1.
ch 0 UCORR 021101 c DRA_AQM_SWITCH: When the switch is on, the
MALG WRFD- Channel active queue management algorithm is used for the
OSWIT 0106140 Configu RNC. 2.
CH 3 ration DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITC
Control H: When the switch is on, the TTI dynamic adjustment
WRFD- (DCCC) algorithm for admission CE-based BE services applies
050405 to the UE with the UL enhanced L2 feature. This
HSUPA
WRFD- parameter is valid when
2ms TTI
0106140 DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH
4 Overboo (DraSwitch) is set to ON. 3.
king on DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH
WRFD-
ATM : When the switch is on, the TTI dynamic adjustment
050408
Transmi algorithm is supported for admission CE-based BE
WRFD- ssion services. 4.
010690
HSUPA DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH:
WRFD- 2ms/ When the switch is on, the TTI dynamic adjustment
010202 10ms algorithm for coverage-based BE services applies to the
WRFD- TTI UE with the UL enhanced L2 feature. This parameter is
010612 Handov valid when
er DRA_BASE_COVER_BE_TTI_RECFG_SWITCH
WRFD-
(DraSwitch) is set to ON. 5.
011502 Overboo
DRA_BASE_COVER_BE_TTI_RECFG_SWITCH:
WRFD- king on
When the switch is on, the TTI dynamic adjustment
010636 IP
algorithm is supported for coverage-based BE services.
Transmi
WRFD- 6. DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH:
ssion
0106101 When the switch is on, the TTI dynamic adjustment
0 TTI algorithm for differentiation-based BE services applies
Switch to the UE with the UL enhanced L2 feature. This
WRFD-
for BE parameter is valid when
0106111
Services DRA_BASE_RES_BE_TTI_RECFG_SWITCH
1
Based (DraSwitch) is set to ON. 7.
WRFD- on DRA_BASE_RES_BE_TTI_RECFG_SWITCH:
0106120 Coverag When the switch is on, the TTI dynamic adjustment
8 e algorithm is supported for differentiation-based BE
UE State services. 8. DRA_DCCC_SWITCH: When the switch
in is on, the dynamic channel reconfiguration control
Connect algorithm is used for the RNC. 9.
ed Mode DRA_HSDPA_DL_FLOW_CONTROL_SWITCH:
(CELL- When the switch is on, flow control is enabled for
DCH, HSDPA services in AM mode. 10.
CELL- DRA_HSDPA_STATE_TRANS_SWITCH: When the
PCH, switch is on, the status of the UE RRC that carrying
URA- HSDPA services can be changed to CELL_FACH at the
PCH, RNC. If a PS BE service is carried over the HS-DSCH,
CELL- the switch PS_BE_STATE_TRANS_SWITCH should
FACH) be on simultaneously. If a PS real-time service is carried
DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH,
DRA_BASE_RES_BE_TTI_RECFG_SWITCH,
DRA_DCCC_SWITCH,
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH,
DRA_HSDPA_STATE_TRANS_SWITCH,
DRA_HSUPA_DCCC_SWITCH,
DRA_HSUPA_STATE_TRANS_SWITCH,
DRA_IP_SERVICE_QOS_SWITCH,
DRA_PS_BE_STATE_TRANS_SWITCH,
DRA_PS_NON_BE_STATE_TRANS_SWITCH,
DRA_R99_DL_FLOW_CONTROL_SWITCH,
DRA_THROUGHPUT_DCCC_SWITCH,
DRA_VOICE_SAVE_CE_SWITCH,
DRA_VOICE_TTI_RECFG_SWITCH,
DRA_CSPS_NO_PERIOD_RETRY_SWITCH,
DRA_SMART_FAST_STATE_TRANS_SWITCH,
DRA_PCH_UE_SMART_P2D_SWITCH,
DRA_BASE_RES_BE_TTI_INIT_SEL_SWITCH,
DRA_BASE_COVER_BE_TTI_INIT_SEL_SWITC
H, DRA_F2U_SWITCH,
DRA_BASE_LOAD_HBD_INIT_SEL_SWITCH
Default Value: DRA_AQM_SWITCH:0,
DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITC
H:0,
DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH
:1,
DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH:
0,
DRA_BASE_COVER_BE_TTI_RECFG_SWITCH:
0, DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH:0,
DRA_BASE_RES_BE_TTI_RECFG_SWITCH:1,
DRA_DCCC_SWITCH:1,
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH:0,
DRA_HSDPA_STATE_TRANS_SWITCH:0,
DRA_HSUPA_DCCC_SWITCH:1,
DRA_HSUPA_STATE_TRANS_SWITCH:0,
DRA_IP_SERVICE_QOS_SWITCH:0,
DRA_PS_BE_STATE_TRANS_SWITCH:1,
DRA_PS_NON_BE_STATE_TRANS_SWITCH:0,
DRA_R99_DL_FLOW_CONTROL_SWITCH:0,
DRA_THROUGHPUT_DCCC_SWITCH:0,
DRA_VOICE_SAVE_CE_SWITCH:0,
DRA_VOICE_TTI_RECFG_SWITCH:0,
DRA_CSPS_NO_PERIOD_RETRY_SWITCH:0,
DRA_SMART_FAST_STATE_TRANS_SWITCH:0,
DRA_PCH_UE_SMART_P2D_SWITCH:0,
ZeroRat BSC690 SET WRFD- Dynami Meaning: Release timer for the PS BE service at a rate
eUpFail 0 UCOIF 021101 c of 0 kbit/s after the DCCC rate increase. For the PS BE
ToRelTi TIMER Channel service at a rate of 0 kbit/s, this parameter is used for the
merLen Configu DCCC rate increase triggered by event 4A.
ration Unsuccessful rate increases indicate that resources are
Control insufficient in the cell. The service at a rate of 0 kbit/s
(DCCC) is unavailable in a short period. If the timer is started,
the 0 kbit/s service is released after the timer expires. If
the value is set to 0, the timer is not started.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 180
ZeroRat BSC691 SET WRFD- Dynami Meaning: Release timer for the PS BE service at a rate
eUpFail 0 UCOIF 021101 c of 0 kbit/s after the DCCC rate increase. For the PS BE
ToRelTi TIMER Channel service at a rate of 0 kbit/s, this parameter is used for the
merLen Configu DCCC rate increase triggered by event 4A.
ration Unsuccessful rate increases indicate that resources are
Control insufficient in the cell. The service at a rate of 0 kbit/s
(DCCC) is unavailable in a short period. If the timer is started,
the 0 kbit/s service is released after the timer expires. If
the value is set to 0, the timer is not started.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 180
BasedTi BSC690 SET WRFD- UE State Meaning: Time threshold for F2D based on
meF2D 0 UUEST 010202 in transmission waiting over FACHs. When this threshold
Thd ATETR Connect is set to 0, the function of F2D based on transmission
ANS ed Mode waiting over FACHs is disabled. When this threshold is
(CELL- not set to 0 and this threshold is exceeded, an F2D state
DCH, transition is triggered. It is recommended that this
CELL- threshold be set to a value smaller than the F2P inactive
PCH, timer to prevent an F2P state transition from being
URA- triggered earlier than an F2D state transition. This
PCH, parameter takes effect only for PS BE services.
CELL- GUI Value Range: 0;20~250
FACH)
Unit: 0.1s
Actual Value Range: 0, 2~25
Default Value: 0
BasedTi BSC691 SET WRFD- UE State Meaning: Time threshold for F2D based on
meF2D 0 UUEST 010202 in transmission waiting over FACHs. When this threshold
Thd ATETR Connect is set to 0, the function of F2D based on transmission
ANS ed Mode waiting over FACHs is disabled. When this threshold is
(CELL- not set to 0 and this threshold is exceeded, an F2D state
DCH, transition is triggered. It is recommended that this
CELL- threshold be set to a value smaller than the F2P inactive
PCH, timer to prevent an F2P state transition from being
URA- triggered earlier than an F2D state transition. This
PCH, parameter takes effect only for PS BE services.
CELL- GUI Value Range: 0;20~250
FACH)
Unit: 0.1s
Actual Value Range: 0, 2~25
Default Value: 0
BasedTi BSC690 SET WRFD- UE State Meaning: When an F2D state transition is triggered
meF2DP 0 UUEST 010202 in because the time threshold for F2D based on
T ATETR Connect transmission waiting over FACHs is exceeded, the RNC
ANS ed Mode does not initiate a D2F state transition if event 4B for
(CELL- PS services is reported and traffic volume or throughput
DCH, is not 0 within the period specified by this parameter. If
CELL- traffic volume or throughput is 0, the RNC initiates a
PCH, D2F state transition. This parameter does not take effect
URA- for D2F state transitions triggered by the expiration of
PCH, the related inactive timer.
CELL- GUI Value Range: 0~240
FACH)
Unit: s
Actual Value Range: 0~240
Default Value: 30
BasedTi BSC691 SET WRFD- UE State Meaning: When an F2D state transition is triggered
meF2DP 0 UUEST 010202 in because the time threshold for F2D based on
T ATETR Connect transmission waiting over FACHs is exceeded, the RNC
ANS ed Mode does not initiate a D2F state transition if event 4B for
(CELL- PS services is reported and traffic volume or throughput
DCH, is not 0 within the period specified by this parameter. If
CELL- traffic volume or throughput is 0, the RNC initiates a
PCH, D2F state transition. This parameter does not take effect
URA- for D2F state transitions triggered by the expiration of
PCH, the related inactive timer.
CELL- GUI Value Range: 0~240
FACH)
Unit: s
Actual Value Range: 0~240
Default Value: 30
PsInactT BSC690 SET WRFD- UE State Meaning: Timer for FD-enabled UEs or LTE-enabled
mrForFs 0 UPSIN 010202 in UEs staying in the CELL_FACH state. When UEs that
tDrmFac ACTTI WRFD- Connect are enabled with Fast Dormancy (FD) and stay in the
h MER 140226 ed Mode CELL_FACH state do not transmit any data after this
(CELL- timer expires, the RNC transits the UEs to the
WRFD- DCH, CELL_PCH state. When LTE-enabled UEs in the
020500 CELL- CELL_FACH state do not transmit any data after this
PCH, timer expires, the RNC transits the UEs to the
URA- CELL_PCH or IDLE state. You can set this timer to a
PCH, value other than 0 if you want to check whether FD-
CELL- enabled UEs and LTE-enabled UEs are in the
FACH) CELL_FACH state.
Fast GUI Value Range: 0~64800
Return Unit: s
from
UMTS Actual Value Range: 0~64800
to LTE Default Value: 5
Enhance
d Fast
Dorman
cy
PsInactT BSC691 SET WRFD- UE State Meaning: Timer for FD-enabled UEs or LTE-enabled
mrForFs 0 UPSIN 010202 in UEs staying in the CELL_FACH state. When UEs that
tDrmFac ACTTI WRFD- Connect are enabled with Fast Dormancy (FD) and stay in the
h MER 140226 ed Mode CELL_FACH state do not transmit any data after this
(CELL- timer expires, the RNC transits the UEs to the
WRFD- DCH, CELL_PCH state. When LTE-enabled UEs in the
020500 CELL- CELL_FACH state do not transmit any data after this
PCH, timer expires, the RNC transits the UEs to the
URA- CELL_PCH or IDLE state. You can set this timer to a
PCH, value other than 0 if you want to check whether FD-
CELL- enabled UEs and LTE-enabled UEs are in the
FACH) CELL_FACH state.
Fast GUI Value Range: 0~64800
Return Unit: s
from
UMTS Actual Value Range: 0~64800
to LTE Default Value: 5
Enhance
d Fast
Dorman
cy
PCH_DISABLED_SWITCH,
SPEC_USER_NONSPT_MSG_REDUCE_SWITCH,
SPECUSER_NONSPT_P2D_SRB_COVSEL_SWIT
CH
Unit: None
Actual Value Range:
SPECUSER_AMR_HOENHANCE_SWITCH,
SPECUSER_AMR_PWRENHANCE_SWITCH,
PCH_DISABLED_SWITCH,
SPEC_USER_NONSPT_MSG_REDUCE_SWITCH,
SPECUSER_NONSPT_P2D_SRB_COVSEL_SWIT
CH
Default Value:
SPECUSER_AMR_HOENHANCE_SWITCH:
0,SPECUSER_AMR_PWRENHANCE_SWITCH:
0,PCH_DISABLED_SWITCH:
0,SPEC_USER_NONSPT_MSG_REDUCE_SWITC
H:
0,SPECUSER_NONSPT_P2D_SRB_COVSEL_SWI
TCH:0
PCH_DISABLED_SWITCH,
SPEC_USER_NONSPT_MSG_REDUCE_SWITCH,
SPECUSER_NONSPT_P2D_SRB_COVSEL_SWIT
CH
Unit: None
Actual Value Range:
SPECUSER_AMR_HOENHANCE_SWITCH,
SPECUSER_AMR_PWRENHANCE_SWITCH,
PCH_DISABLED_SWITCH,
SPEC_USER_NONSPT_MSG_REDUCE_SWITCH,
SPECUSER_NONSPT_P2D_SRB_COVSEL_SWIT
CH
Default Value:
SPECUSER_AMR_HOENHANCE_SWITCH:
0,SPECUSER_AMR_PWRENHANCE_SWITCH:
0,PCH_DISABLED_SWITCH:
0,SPEC_USER_NONSPT_MSG_REDUCE_SWITC
H:
0,SPECUSER_NONSPT_P2D_SRB_COVSEL_SWI
TCH:0
TAC_F BSC690 ADD WRFD- Termina Meaning: The function of the TAC.If Fast_Dormancy
UNC 0 UIMEIT 160103 l Black is selected, the TAC specifies the UEs that are enabled
AC WRFD- List with the Fast Dormancy feature; if
MOD 020500 Enhance HSDPA_RB_Setup_Cmp_CRC is selected, the TAC
UIMEIT d Fast specifies that the UEs want to establish services on
AC Dorman HSDPA, however, the RNC sets up services on the
cy DCH, and retries on HSDPA later; if Special_User_En-
RMV hance is selected, the TAC specifies the UEs that are
UIMEIT enabled with the Special User Enhance feature.
AC
GUI Value Range: Fast_Dormancy,
HSDPA_RB_Setup_Cmp_CRC, Special_User_En-
hance
Unit: None
Actual Value Range: Fast_Dormancy,
HSDPA_RB_Setup_Cmp_CRC, Special_User_En-
hance
Default Value: None
TAC_F BSC691 ADD WRFD- Termina Meaning: The function of the TAC.If Fast_Dormancy
UNC 0 UIMEIT 160103 l Black is selected, the TAC specifies the UEs that are enabled
AC WRFD- List with the Fast Dormancy feature; if
MOD 020500 Enhance HSDPA_RB_Setup_Cmp_CRC is selected, the TAC
UIMEIT d Fast specifies that the UEs want to establish services on
AC Dorman HSDPA, however, the RNC sets up services on the
cy DCH, and retries on HSDPA later; if Special_User_En-
RMV hance is selected, the TAC specifies the UEs that are
UIMEIT enabled with the Special User Enhance feature.
AC
GUI Value Range: Fast_Dormancy,
HSDPA_RB_Setup_Cmp_CRC, Special_User_En-
hance
Unit: None
Actual Value Range: Fast_Dormancy,
HSDPA_RB_Setup_Cmp_CRC, Special_User_En-
hance
Default Value: None
StateTra BSC690 SET WRFD- UE State Meaning: Redundancy coefficient for event 4B
nsTraff 0 UUEST 010202 in measurement reports in the optimized state transition
Redund ATETR Connect algorithm. This parameter is used to minimize incorrect
Coef ANS ed Mode UE activity decisions caused by loss of traffic volume
(CELL- or throughput reports. Event 4B report threshold =
DCH, Maximum number of event 4B reports for traffic
CELL- volume or throughput x "StateTransTraffRedundCoef".
PCH, A UE is regarded as in the low activity state if the
URA- number of received event 4B reports in the period
PCH, specified by the state transition timer is greater than the
CELL- event 4B report threshold. This parameter is an
FACH) advanced parameter. To modify this parameter, contact
Huawei Customer Service Center for technical support.
GUI Value Range: 0~100
Unit: None
Actual Value Range: 0~1, step: 0.01
Default Value: 80
StateTra BSC691 SET WRFD- UE State Meaning: Redundancy coefficient for event 4B
nsTraff 0 UUEST 010202 in measurement reports in the optimized state transition
Redund ATETR Connect algorithm. This parameter is used to minimize incorrect
Coef ANS ed Mode UE activity decisions caused by loss of traffic volume
(CELL- or throughput reports. Event 4B report threshold =
DCH, Maximum number of event 4B reports for traffic
CELL- volume or throughput x "StateTransTraffRedundCoef".
PCH, A UE is regarded as in the low activity state if the
URA- number of received event 4B reports in the period
PCH, specified by the state transition timer is greater than the
CELL- event 4B report threshold. This parameter is an
FACH) advanced parameter. To modify this parameter, contact
Huawei Customer Service Center for technical support.
GUI Value Range: 0~100
Unit: None
Actual Value Range: 0~1, step: 0.01
Default Value: 80
BeD2FS BSC690 SET WRFD- UE State Meaning: Timer for state transition from DCH to FACH
tateTran 0 UUEST 010202 in of BE services, used to check whether the UE in the
sTimer ATETR Connect CELL_DCH state with BE services is in the stable low
ANSTI ed Mode activity state.
MER (CELL- GUI Value Range: 1~65535
DCH,
CELL- Unit: s
PCH, Actual Value Range: 1~65535
URA- Default Value: 5
PCH,
CELL-
FACH)
BeD2FS BSC691 SET WRFD- UE State Meaning: Timer for state transition from DCH to FACH
tateTran 0 UUEST 010202 in of BE services, used to check whether the UE in the
sTimer ATETR Connect CELL_DCH state with BE services is in the stable low
ANSTI ed Mode activity state.
MER (CELL- GUI Value Range: 1~65535
DCH,
CELL- Unit: s
PCH, Actual Value Range: 1~65535
URA- Default Value: 5
PCH,
CELL-
FACH)
D2F2PT BSC690 SET WRFD- UE State Meaning: This parameter is used to check whether the
vmThd 0 UUEST 010202 in UE in the low activity state. If the UE is on DCH
ATETR Connect channel, the low activity counter increases by 1 every
ANS ed Mode time traffic volume event 4B is reported. If the UE is on
(CELL- FACH channel, the low activity counter increases by 1
DCH, if the traffic volume is 0 in the traffic volume event 4B
CELL- report.
PCH, GUI Value Range: D8, D16, D32, D64, D128, D256,
URA- D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
PCH, D24k, D32k, D48k, D64k, D96k, D128k, D192k,
CELL- D256k, D384k, D512k, D768k
FACH)
Unit: byte
Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k, 768k
Default Value: D128
D2F2PT BSC691 SET WRFD- UE State Meaning: This parameter is used to check whether the
vmThd 0 UUEST 010202 in UE in the low activity state. If the UE is on DCH
ATETR Connect channel, the low activity counter increases by 1 every
ANS ed Mode time traffic volume event 4B is reported. If the UE is on
(CELL- FACH channel, the low activity counter increases by 1
DCH, if the traffic volume is 0 in the traffic volume event 4B
CELL- report.
PCH, GUI Value Range: D8, D16, D32, D64, D128, D256,
URA- D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
PCH, D24k, D32k, D48k, D64k, D96k, D128k, D192k,
CELL- D256k, D384k, D512k, D768k
FACH)
Unit: byte
Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k, 768k
Default Value: D128
D2FTv BSC690 SET WRFD- UE State Meaning: When the traffic volume is below the 4B
mTimeT 0 UUEST 010202 in threshold and remains so for the period specified by this
oTrig ATETR Connect parameter, the event 4B is reported. This parameter can
ANS ed Mode prevent unnecessary reports to be triggered, caused by
(CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D5000
D2FTv BSC691 SET WRFD- UE State Meaning: When the traffic volume is below the 4B
mTimeT 0 UUEST 010202 in threshold and remains so for the period specified by this
oTrig ATETR Connect parameter, the event 4B is reported. This parameter can
ANS ed Mode prevent unnecessary reports to be triggered, caused by
(CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D5000
D2FTv BSC690 SET WRFD- UE State Meaning: Pending time after the traffic volume event
mPTAT 0 UUEST 010202 in 4B for state transition from DCH to FACH is reported.
ATETR Connect This parameter is used to prevent too many traffic
ANS ed Mode volume events 4B being reported.
(CELL- GUI Value Range: D250, D500, D1000, D2000, D4000,
DCH, D8000, D16000
CELL-
PCH, Unit: ms
URA- Actual Value Range: 250, 500, 1000, 2000, 4000, 8000,
PCH, 16000
CELL- Default Value: D1000
FACH)
D2FTv BSC691 SET WRFD- UE State Meaning: Pending time after the traffic volume event
mPTAT 0 UUEST 010202 in 4B for state transition from DCH to FACH is reported.
ATETR Connect This parameter is used to prevent too many traffic
ANS ed Mode volume events 4B being reported.
(CELL- GUI Value Range: D250, D500, D1000, D2000, D4000,
DCH, D8000, D16000
CELL-
PCH, Unit: ms
URA- Actual Value Range: 250, 500, 1000, 2000, 4000, 8000,
PCH, 16000
CELL- Default Value: D1000
FACH)
BeH2FS BSC690 SET WRFD- UE State Meaning: Timer for state transition from HS-DSCH to
tateTran 0 UUEST 010202 in FACH of BE services, used to check whether the UE in
sTimer ATETR WRFD- Connect the CELL_DCH(with HS-DSCH) state with BE
ANSTI 0106111 ed Mode services is in the stable low activity state.
MER 1 (CELL- GUI Value Range: 1~65535
DCH,
CELL- Unit: s
PCH, Actual Value Range: 1~65535
URA- Default Value: 5
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
BeH2FS BSC691 SET WRFD- UE State Meaning: Timer for state transition from HS-DSCH to
tateTran 0 UUEST 010202 in FACH of BE services, used to check whether the UE in
sTimer ATETR WRFD- Connect the CELL_DCH(with HS-DSCH) state with BE
ANSTI 0106111 ed Mode services is in the stable low activity state.
MER 1 (CELL- GUI Value Range: 1~65535
DCH,
CELL- Unit: s
PCH, Actual Value Range: 1~65535
URA- Default Value: 5
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
BeH2FT BSC690 SET WRFD- UE State Meaning: This parameter is used to check whether the
vmThd 0 UUEST 010202 in UE in the low activity state. If the UE is on HS-DSCH
ATETR WRFD- Connect channel, the low activity counter increases by 1 every
ANS 0106111 ed Mode time traffic volume event 4B is reported.
1 (CELL- GUI Value Range: D8, D16, D32, D64, D128, D256,
DCH, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
CELL- D24k, D32k, D48k, D64k, D96k, D128k, D192k,
PCH, D256k, D384k, D512k, D768k
URA-
PCH, Unit: byte
CELL- Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
FACH) 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
HSDPA 128k, 192k, 256k, 384k, 512k, 768k
State Default Value: D128
Transiti
on
BeH2FT BSC691 SET WRFD- UE State Meaning: This parameter is used to check whether the
vmThd 0 UUEST 010202 in UE in the low activity state. If the UE is on HS-DSCH
ATETR WRFD- Connect channel, the low activity counter increases by 1 every
ANS 0106111 ed Mode time traffic volume event 4B is reported.
1 (CELL- GUI Value Range: D8, D16, D32, D64, D128, D256,
DCH, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
CELL- D24k, D32k, D48k, D64k, D96k, D128k, D192k,
PCH, D256k, D384k, D512k, D768k
URA-
PCH, Unit: byte
CELL- Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
FACH) 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
HSDPA 128k, 192k, 256k, 384k, 512k, 768k
State Default Value: D128
Transiti
on
BeH2FT BSC690 SET WRFD- UE State Meaning: When the traffic volume is below the 4B
vmTime 0 UUEST 010202 in threshold and remains so for the period specified by this
ToTrig ATETR WRFD- Connect parameter, the event 4B is reported. This parameter can
ANS 0106111 ed Mode prevent unnecessary reports to be triggered, caused by
1 (CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
HSDPA Default Value: D5000
State
Transiti
on
BeH2FT BSC691 SET WRFD- UE State Meaning: When the traffic volume is below the 4B
vmTime 0 UUEST 010202 in threshold and remains so for the period specified by this
ToTrig ATETR WRFD- Connect parameter, the event 4B is reported. This parameter can
ANS 0106111 ed Mode prevent unnecessary reports to be triggered, caused by
1 (CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
HSDPA Default Value: D5000
State
Transiti
on
BeH2FT BSC690 SET WRFD- UE State Meaning: Pending time after the traffic volume event
vmPTA 0 UUEST 010202 in 4B for state transition from HSPA to FACH is reported.
T ATETR WRFD- Connect This parameter is used to prevent too many traffic
ANS 0106111 ed Mode volume events 4B being reported.
1 (CELL- GUI Value Range: D250, D500, D1000, D2000, D4000,
DCH, D8000, D16000
CELL-
PCH, Unit: ms
URA- Actual Value Range: 250, 500, 1000, 2000, 4000, 8000,
PCH, 16000
CELL- Default Value: D1000
FACH)
HSDPA
State
Transiti
on
BeH2FT BSC691 SET WRFD- UE State Meaning: Pending time after the traffic volume event
vmPTA 0 UUEST 010202 in 4B for state transition from HSPA to FACH is reported.
T ATETR WRFD- Connect This parameter is used to prevent too many traffic
ANS 0106111 ed Mode volume events 4B being reported.
1 (CELL- GUI Value Range: D250, D500, D1000, D2000, D4000,
DCH, D8000, D16000
CELL-
PCH, Unit: ms
URA- Actual Value Range: 250, 500, 1000, 2000, 4000, 8000,
PCH, 16000
CELL- Default Value: D1000
FACH)
HSDPA
State
Transiti
on
RtDH2F BSC690 SET WRFD- UE State Meaning: Timer for state transition from DCH or HSPA
StateTra 0 UUEST 010202 in to FACH of real-time services, used to check whether
nsTimer ATETR Connect the UE in the CELL_DCH state with real-time services
ANSTI ed Mode is in the stable low activity state.
MER (CELL- GUI Value Range: 1~65535
DCH,
CELL- Unit: s
PCH, Actual Value Range: 1~65535
URA- Default Value: 180
PCH,
CELL-
FACH)
RtDH2F BSC691 SET WRFD- UE State Meaning: Timer for state transition from DCH or HSPA
StateTra 0 UUEST 010202 in to FACH of real-time services, used to check whether
nsTimer ATETR Connect the UE in the CELL_DCH state with real-time services
ANSTI ed Mode is in the stable low activity state.
MER (CELL- GUI Value Range: 1~65535
DCH,
CELL- Unit: s
PCH, Actual Value Range: 1~65535
URA- Default Value: 180
PCH,
CELL-
FACH)
RtDH2F BSC690 SET WRFD- UE State Meaning: This parameter is used to check whether the
TvmThd 0 UUEST 010202 in UE in the low activity state. If the UE is on DCH or
ATETR Connect HSPA channel, the low activity counter increases by 1
ANS ed Mode every time traffic volume event 4B is reported.
(CELL- GUI Value Range: D8, D16, D32, D64, D128, D256,
DCH, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
CELL- D24k, D32k, D48k, D64k, D96k, D128k, D192k,
PCH, D256k, D384k, D512k, D768k
URA-
PCH, Unit: byte
CELL- Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
FACH) 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k, 768k
Default Value: D64
RtDH2F BSC691 SET WRFD- UE State Meaning: This parameter is used to check whether the
TvmThd 0 UUEST 010202 in UE in the low activity state. If the UE is on DCH or
ATETR Connect HSPA channel, the low activity counter increases by 1
ANS ed Mode every time traffic volume event 4B is reported.
(CELL- GUI Value Range: D8, D16, D32, D64, D128, D256,
DCH, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
CELL- D24k, D32k, D48k, D64k, D96k, D128k, D192k,
PCH, D256k, D384k, D512k, D768k
URA-
PCH, Unit: byte
CELL- Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
FACH) 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k, 768k
Default Value: D64
RtDH2F BSC690 SET WRFD- UE State Meaning: When the traffic volume is below the 4B
TvmTim 0 UUEST 010202 in threshold and remains so for the period specified by this
eToTrig ATETR Connect parameter, the event 4B is reported. This parameter can
ANS ed Mode prevent unnecessary reports to be triggered, caused by
(CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D5000
RtDH2F BSC691 SET WRFD- UE State Meaning: When the traffic volume is below the 4B
TvmTim 0 UUEST 010202 in threshold and remains so for the period specified by this
eToTrig ATETR Connect parameter, the event 4B is reported. This parameter can
ANS ed Mode prevent unnecessary reports to be triggered, caused by
(CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D5000
RtDH2F BSC690 SET WRFD- UE State Meaning: Pending time after the traffic volume event
TvmPT 0 UUEST 010202 in 4B for state transition from DCH or HSPA to FACH
AT ATETR Connect transition is reported. This parameter is used to prevent
ANS ed Mode too many traffic volume events 4B being reported.
(CELL- GUI Value Range: D250, D500, D1000, D2000, D4000,
DCH, D8000, D16000
CELL-
PCH, Unit: ms
URA- Actual Value Range: 250, 500, 1000, 2000, 4000, 8000,
PCH, 16000
CELL- Default Value: D16000
FACH)
RtDH2F BSC691 SET WRFD- UE State Meaning: Pending time after the traffic volume event
TvmPT 0 UUEST 010202 in 4B for state transition from DCH or HSPA to FACH
AT ATETR Connect transition is reported. This parameter is used to prevent
ANS ed Mode too many traffic volume events 4B being reported.
(CELL- GUI Value Range: D250, D500, D1000, D2000, D4000,
DCH, D8000, D16000
CELL-
PCH, Unit: ms
URA- Actual Value Range: 250, 500, 1000, 2000, 4000, 8000,
PCH, 16000
CELL- Default Value: D16000
FACH)
BeE2FS BSC690 SET WRFD- UE State Meaning: Timer for state transition from E-DCH to
tateTran 0 UUEST 010202 in FACH of BE services, used to check whether the UE in
sTimer ATETR Connect the CELL_DCH(with E-DCH) state with BE services is
ANSTI ed Mode in the stable low activity state.
MER (CELL- GUI Value Range: 1~65535
DCH,
CELL- Unit: s
PCH, Actual Value Range: 1~65535
URA- Default Value: 2
PCH,
CELL-
FACH)
BeE2FS BSC691 SET WRFD- UE State Meaning: Timer for state transition from E-DCH to
tateTran 0 UUEST 010202 in FACH of BE services, used to check whether the UE in
sTimer ATETR Connect the CELL_DCH(with E-DCH) state with BE services is
ANSTI ed Mode in the stable low activity state.
MER (CELL- GUI Value Range: 1~65535
DCH,
CELL- Unit: s
PCH, Actual Value Range: 1~65535
URA- Default Value: 2
PCH,
CELL-
FACH)
E2FThr BSC690 SET WRFD- UE State Meaning: This parameter is used to check whether the
ouThd 0 UUEST 010202 in UE in the low activity state. If the UE is on the E-DCH
ATETR WRFD- Connect channel, the low activity counter increases by 1 every
ANS 021101 ed Mode time throughput ratio event 4B is reported.
(CELL- GUI Value Range: 0~384
DCH,
CELL- Unit: kbit/s
PCH, Actual Value Range: 0~384
URA- Default Value: 8
PCH,
CELL-
FACH)
Dynami
c
Channel
Configu
ration
Control
(DCCC)
E2FThr BSC691 SET WRFD- UE State Meaning: This parameter is used to check whether the
ouThd 0 UUEST 010202 in UE in the low activity state. If the UE is on the E-DCH
ATETR WRFD- Connect channel, the low activity counter increases by 1 every
ANS 021101 ed Mode time throughput ratio event 4B is reported.
(CELL- GUI Value Range: 0~384
DCH,
CELL- Unit: kbit/s
PCH, Actual Value Range: 0~384
URA- Default Value: 8
PCH,
CELL-
FACH)
Dynami
c
Channel
Configu
ration
Control
(DCCC)
E2FThr BSC690 SET WRFD- UE State Meaning: Number of periods before the throughput
ouTime 0 UUEST 010202 in ratio event 4B for state transition from E-DCH to FACH
ToTrig ATETR WRFD- Connect is triggered. When the throughput ratio is below the
ANS 021101 ed Mode lower threshold and remains so for the period specified
(CELL- by this parameter, the event 4B is reported. This
WRFD- DCH, parameter can prevent unnecessary reports to be
0106120 CELL- triggered, caused by traffic volume variation. Time to
8 PCH, trigger the throughput ratio event 4B = value of this
URA- parameter x measurement period x 10 ms.
PCH, GUI Value Range: 0~1023
CELL-
FACH) Unit: None
E2FThr BSC691 SET WRFD- UE State Meaning: Number of periods before the throughput
ouTime 0 UUEST 010202 in ratio event 4B for state transition from E-DCH to FACH
ToTrig ATETR WRFD- Connect is triggered. When the throughput ratio is below the
ANS 021101 ed Mode lower threshold and remains so for the period specified
(CELL- by this parameter, the event 4B is reported. This
WRFD- DCH, parameter can prevent unnecessary reports to be
0106120 CELL- triggered, caused by traffic volume variation. Time to
8 PCH, trigger the throughput ratio event 4B = value of this
URA- parameter x measurement period x 10 ms.
PCH, GUI Value Range: 0~1023
CELL-
FACH) Unit: None
E2FThr BSC690 SET WRFD- Dynami Meaning: Period of E-DCH throughput ratio
ouMeas 0 UUEST 021101 c measurement. This parameter specifies the period of E-
Period ATETR WRFD- Channel DCH throughput ratio measurement. The throughput
ANS 0106120 Configu ratio over the E-DCH is periodically measured to
8 ration implement state transition from E-DCH to FACH and
Control DCCC algorithm on EDCH.
(DCCC) GUI Value Range: 1~10000
HSUPA Unit: 10ms
DCCC
Actual Value Range: 10~100000
Default Value: 30
E2FThr BSC691 SET WRFD- Dynami Meaning: Period of E-DCH throughput ratio
ouMeas 0 UUEST 021101 c measurement. This parameter specifies the period of E-
Period ATETR WRFD- Channel DCH throughput ratio measurement. The throughput
ANS 0106120 Configu ratio over the E-DCH is periodically measured to
8 ration implement state transition from E-DCH to FACH and
Control DCCC algorithm on EDCH.
(DCCC) GUI Value Range: 1~10000
HSUPA Unit: 10ms
DCCC
Actual Value Range: 10~100000
Default Value: 30
E2FThr BSC690 SET WRFD- UE State Meaning: Number of pending periods after the
ouPTAT 0 UUEST 010202 in throughput event 4B for state transition from E-DCH to
ATETR WRFD- Connect FACH is triggered. This parameter is used to prevent
ANS 021101 ed Mode too many throughput events 4B being reported. Pending
(CELL- time after the throughput event 4B is triggered = value
WRFD- DCH, of this parameter x measurement period x 10 ms.
0106120 CELL-
8 GUI Value Range: 0~1023
PCH,
URA- Unit: None
PCH, Actual Value Range: 0~1023
CELL- Default Value: 4
FACH)
Dynami
c
Channel
Configu
ration
Control
(DCCC)
HSUPA
DCCC
E2FThr BSC691 SET WRFD- UE State Meaning: Number of pending periods after the
ouPTAT 0 UUEST 010202 in throughput event 4B for state transition from E-DCH to
ATETR WRFD- Connect FACH is triggered. This parameter is used to prevent
ANS 021101 ed Mode too many throughput events 4B being reported. Pending
(CELL- time after the throughput event 4B is triggered = value
WRFD- DCH, of this parameter x measurement period x 10 ms.
0106120 CELL-
8 GUI Value Range: 0~1023
PCH,
URA- Unit: None
PCH, Actual Value Range: 0~1023
CELL- Default Value: 4
FACH)
Dynami
c
Channel
Configu
ration
Control
(DCCC)
HSUPA
DCCC
DcccStg BSC690 SET WRFD- Dynami Meaning: Strategy for adjustment of the rate of the PS
0 UDCCC 021101 c BE service when the UE is in the CELL_DCH state.
Channel RATE_UP_AND_DOWN_ON_DCH indicates that
Configu the rate over the DCH can be raised or lowered.
ration RATE_UP_ONLY indicates that the rate over the DCH
Control can only be raised. When UE is in low activity state, it
(DCCC) is no need to degrade the traffic rate to the threshold for
DCCC before state transition to CELL_FACH. That
means UE can transit to CELL_FACH state at any rate.
GUI Value Range:
RATE_UP_AND_DOWN_ON_DCH,
RATE_UP_ONLY_ON_DCH
Unit: None
Actual Value Range:
RATE_UP_AND_DOWN_ON_DCH,
RATE_UP_ONLY_ON_DCH
Default Value: RATE_UP_AND_DOWN_ON_DCH
DcccStg BSC691 SET WRFD- Dynami Meaning: Strategy for adjustment of the rate of the PS
0 UDCCC 021101 c BE service when the UE is in the CELL_DCH state.
Channel RATE_UP_AND_DOWN_ON_DCH indicates that
Configu the rate over the DCH can be raised or lowered.
ration RATE_UP_ONLY indicates that the rate over the DCH
Control can only be raised. When UE is in low activity state, it
(DCCC) is no need to degrade the traffic rate to the threshold for
DCCC before state transition to CELL_FACH. That
means UE can transit to CELL_FACH state at any rate.
GUI Value Range:
RATE_UP_AND_DOWN_ON_DCH,
RATE_UP_ONLY_ON_DCH
Unit: None
Actual Value Range:
RATE_UP_AND_DOWN_ON_DCH,
RATE_UP_ONLY_ON_DCH
Default Value: RATE_UP_AND_DOWN_ON_DCH
UlDccc BSC690 SET WRFD- Dynami Meaning: Uplink bit rate threshold for DCCC. When the
RateThd 0 UDCCC 021101 c maximum uplink bit rate of a BE service is larger than
Channel this parameter value, the traffic-based uplink DCCC
Configu function can take effect for the UE. Otherwise, the
ration function cannot take effect for the UE.
Control GUI Value Range: D8, D16, D32, D64, D128, D144,
(DCCC) D256, D384
Unit: kbit/s
Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384
Default Value: D64
UlDccc BSC691 SET WRFD- Dynami Meaning: Uplink bit rate threshold for DCCC. When the
RateThd 0 UDCCC 021101 c maximum uplink bit rate of a BE service is larger than
Channel this parameter value, the traffic-based uplink DCCC
Configu function can take effect for the UE. Otherwise, the
ration function cannot take effect for the UE.
Control GUI Value Range: D8, D16, D32, D64, D128, D144,
(DCCC) D256, D384
Unit: kbit/s
Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384
Default Value: D64
DlDccc BSC690 SET WRFD- Dynami Meaning: Downlink bit rate threshold for DCCC. When
RateThd 0 UDCCC 021101 c the maximum downlink bit rate of a BE service is larger
WRFD- Channel than this parameter value, the traffic-based downlink
020107 Configu DCCC function can take effect for the UE. Otherwise,
ration the function cannot take effect for the UE.
Control GUI Value Range: D8, D16, D32, D64, D128, D144,
(DCCC) D256, D384
Overloa Unit: kbit/s
d
Control Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384
Default Value: D64
DlDccc BSC691 SET WRFD- Dynami Meaning: Downlink bit rate threshold for DCCC. When
RateThd 0 UDCCC 021101 c the maximum downlink bit rate of a BE service is larger
WRFD- Channel than this parameter value, the traffic-based downlink
020107 Configu DCCC function can take effect for the UE. Otherwise,
ration the function cannot take effect for the UE.
Control GUI Value Range: D8, D16, D32, D64, D128, D144,
(DCCC) D256, D384
Overloa Unit: kbit/s
d
Control Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384
Default Value: D64
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_S
WITCH: The NodeB baseband board uses different
processing specifications for users with different uplink
bearer services, for example, HSUPA TTI 2 ms
services, HSUPA TTI 10 ms services, and R99 services.
When serving a large number of users, the system
cannot guarantee that all users can access the network
with the highest service bearer supported by UEs. This
switch controls whether the RNC allocates
corresponding channels for new users based on the cell
capability reported through the NodeB private interface.
When this switch is turned on, the RNC dynamically
selects an appropriate uplink service bearer and
allocates corresponding channels for new users to
maximize the system capacity based on the actual
NodeB processing specifications. When this switch is
turned off, the optimization process is disabled. 18.
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWI
TCH: Whether to use the optimized TTI switching
algorithm for BE services When this switch is turned
off, the optimized algorithm does not take effect. The
original mechanism is implemented. When this switch
is turned on, the optimized algorithm takes effect. After
HSUPA services are configured or reconfigured with 10
ms TTI due to network resource (admission CEs,
RTWP, consumed Iub bandwidth, or consumed CEs)
congestion or insufficient coverage, these UEs cannot
change to use 2 ms TTI if no data needs to be
transmitted. 19.
PERFENH_DOWNLOAD_ENHANCE_SWITCH:
Whether to activate the algorithm for increasing the
single-threaded download rate. 20.
PERFENH_OLPC_BLER_COEF_ADJUST: Switch
for adjusting the BLER coefficient specific to CS
services based on the best cell's uplink load status. When
this switch is turned on, the outer loop power control
algorithm uses the target BLER set by the OMU board
if the best cell's uplink load status is LDR or OLC. If the
status is neither LDR nor OLC, this algorithm uses this
target BLER after being divided by five. 21.
PERFENH_EMG_AGPS_MC_DELAY_SWITCH:
Whether to enable the function of delaying the sending
of an RRC_MEAS_CTRL message containing AGPS
information when an emergency call is made. When this
switch is turned on, the RNC delays the sending of this
message until the emergency call is successfully set up.
When this switch is turned off, the RNC sends this
PERFENH_DLBLINDDETECT_WHEN_ONLYSR-
BONDCH,
PERFENH_DLBLINDDETECT_WHEN_SRBAM-
RONDCH,
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT
Unit: None
Actual Value Range:
PERFENH_AMR_SPEC_BR_SWITCH,
PERFENH_AMR_TMPLT_SWITCH,
PERFENH_SRB_TMPLT_SWITCH,
PERFENH_OLPC_TMPLT_SWITCH,
PERFENH_AMR_SP_TMPLT_SWITCH,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH,
PERFENH_INTERRAT_PENALTY_50_SWITCH,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH,
PERFENH_UU_P2D_CUC_OPT_SWITCH,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH
, PERFENH_RRC_REDIR_PROTECT_SWITCH,
PERFENH_H2F_OPT_SWITCH,
PERFENH_PSTRAFFIC_P2H_SWITCH,
PERFENH_VIP_USER_PCHR_MR_SWITCH,
PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH
,
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_S
WITCH,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWI
TCH,
PERFENH_DOWNLOAD_ENHANCE_SWITCH,
PERFENH_OLPC_BLER_COEF_ADJUST,
PERFENH_EMG_AGPS_MC_DELAY_SWITCH,
PERFENH_MULTI_RLS_CQI_PARA_OPT_SWITC
H,
PERFENH_RELOC_IE_CALCTIMEFORCIP_SWIT
CH,
PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH,
PERFENH_CELL_CACLOAD_BROADCAST_AM
END,
PERFENH_MBDR_TARCELLSEL_OPT_SWITCH,
PERFENH_RRC_DRD_PREADMISSION_SWITCH
, PERFENH_RRC_WEAK_REDIR_SWITCH,
PERFENH_L2U_CSFB_COMMCALL_SWITCH,
PERFENH_DLBLINDDETECT_WHEN_ONLYSR-
BONDCH,
PERFENH_DLBLINDDETECT_WHEN_SRBAM-
RONDCH,
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT
Default Value:
PERFENH_AMR_SPEC_BR_SWITCH:
1,PERFENH_AMR_TMPLT_SWITCH:
1,PERFENH_SRB_TMPLT_SWITCH:
1,PERFENH_OLPC_TMPLT_SWITCH:
1,PERFENH_AMR_SP_TMPLT_SWITCH:
1,PERFENH_INTRAFREQ_MC_TMPLT_SWITCH:
1,PERFENH_INTERRAT_PENALTY_50_SWITCH:
1,PERFENH_SRB_OVER_HSUPA_TTI10_SWITC
H:
0,PERFENH_HSUPA_TTI2_ENHANCE_SWITCH:
0,PERFENH_UU_P2D_CUC_OPT_SWITCH:
0,PERFENH_RL_RECFG_SIR_CONSIDER_SWITC
H:1,PERFENH_RRC_REDIR_PROTECT_SWITCH:
0,PERFENH_H2F_OPT_SWITCH:
0,PERFENH_PSTRAFFIC_P2H_SWITCH:
0,PERFENH_VIP_USER_PCHR_MR_SWITCH:
0,PERFENH_TX_INTERRUPT_AFT_TRIG_SWITC
H:
0,PERFENH_CELL_HSUPA_CAP_CHANGE_OPT
_SWITCH:0,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWI
TCH:
0,PERFENH_DOWNLOAD_ENHANCE_SWITCH:
0,PERFENH_OLPC_BLER_COEF_ADJUST:
1,PERFENH_EMG_AGPS_MC_DELAY_SWITCH:
0,PERFENH_MULTI_RLS_CQI_PARA_OPT_SWIT
CH:
0,PERFENH_RELOC_IE_CALCTIMEFORCIP_SWI
TCH:
0,PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH:
0,PERFENH_CELL_CACLOAD_BROADCAST_A
MEND:
1,PERFENH_MBDR_TARCELLSEL_OPT_SWITC
H:
0,PERFENH_RRC_DRD_PREADMISSION_SWITC
H:0,PERFENH_RRC_WEAK_REDIR_SWITCH:
0,PERFENH_L2U_CSFB_COMMCALL_SWITCH:
0,PERFENH_DLBLINDDETECT_WHEN_ON-
LYSRBONDCH:
0,PERFENH_DLBLINDDETECT_WHEN_SRBAM-
RONDCH:
0,PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIM-
IT:0
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_S
WITCH: The NodeB baseband board uses different
processing specifications for users with different uplink
bearer services, for example, HSUPA TTI 2 ms
services, HSUPA TTI 10 ms services, and R99 services.
When serving a large number of users, the system
cannot guarantee that all users can access the network
with the highest service bearer supported by UEs. This
switch controls whether the RNC allocates
corresponding channels for new users based on the cell
capability reported through the NodeB private interface.
When this switch is turned on, the RNC dynamically
selects an appropriate uplink service bearer and
allocates corresponding channels for new users to
maximize the system capacity based on the actual
NodeB processing specifications. When this switch is
turned off, the optimization process is disabled. 18.
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWI
TCH: Whether to use the optimized TTI switching
algorithm for BE services When this switch is turned
off, the optimized algorithm does not take effect. The
original mechanism is implemented. When this switch
is turned on, the optimized algorithm takes effect. After
HSUPA services are configured or reconfigured with 10
ms TTI due to network resource (admission CEs,
RTWP, consumed Iub bandwidth, or consumed CEs)
congestion or insufficient coverage, these UEs cannot
change to use 2 ms TTI if no data needs to be
transmitted. 19.
PERFENH_DOWNLOAD_ENHANCE_SWITCH:
Whether to activate the algorithm for increasing the
single-threaded download rate. 20.
PERFENH_OLPC_BLER_COEF_ADJUST: Switch
for adjusting the BLER coefficient specific to CS
services based on the best cell's uplink load status. When
this switch is turned on, the outer loop power control
algorithm uses the target BLER set by the OMU board
if the best cell's uplink load status is LDR or OLC. If the
status is neither LDR nor OLC, this algorithm uses this
target BLER after being divided by five. 21.
PERFENH_EMG_AGPS_MC_DELAY_SWITCH:
Whether to enable the function of delaying the sending
of an RRC_MEAS_CTRL message containing AGPS
information when an emergency call is made. When this
switch is turned on, the RNC delays the sending of this
message until the emergency call is successfully set up.
When this switch is turned off, the RNC sends this
PERFENH_DLBLINDDETECT_WHEN_ONLYSR-
BONDCH,
PERFENH_DLBLINDDETECT_WHEN_SRBAM-
RONDCH,
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT
Unit: None
Actual Value Range:
PERFENH_AMR_SPEC_BR_SWITCH,
PERFENH_AMR_TMPLT_SWITCH,
PERFENH_SRB_TMPLT_SWITCH,
PERFENH_OLPC_TMPLT_SWITCH,
PERFENH_AMR_SP_TMPLT_SWITCH,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH,
PERFENH_INTERRAT_PENALTY_50_SWITCH,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH,
PERFENH_UU_P2D_CUC_OPT_SWITCH,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH
, PERFENH_RRC_REDIR_PROTECT_SWITCH,
PERFENH_H2F_OPT_SWITCH,
PERFENH_PSTRAFFIC_P2H_SWITCH,
PERFENH_VIP_USER_PCHR_MR_SWITCH,
PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH
,
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_S
WITCH,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWI
TCH,
PERFENH_DOWNLOAD_ENHANCE_SWITCH,
PERFENH_OLPC_BLER_COEF_ADJUST,
PERFENH_EMG_AGPS_MC_DELAY_SWITCH,
PERFENH_MULTI_RLS_CQI_PARA_OPT_SWITC
H,
PERFENH_RELOC_IE_CALCTIMEFORCIP_SWIT
CH,
PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH,
PERFENH_CELL_CACLOAD_BROADCAST_AM
END,
PERFENH_MBDR_TARCELLSEL_OPT_SWITCH,
PERFENH_RRC_DRD_PREADMISSION_SWITCH
, PERFENH_RRC_WEAK_REDIR_SWITCH,
PERFENH_L2U_CSFB_COMMCALL_SWITCH,
PERFENH_DLBLINDDETECT_WHEN_ONLYSR-
BONDCH,
PERFENH_DLBLINDDETECT_WHEN_SRBAM-
RONDCH,
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT
Default Value:
PERFENH_AMR_SPEC_BR_SWITCH:
1,PERFENH_AMR_TMPLT_SWITCH:
1,PERFENH_SRB_TMPLT_SWITCH:
1,PERFENH_OLPC_TMPLT_SWITCH:
1,PERFENH_AMR_SP_TMPLT_SWITCH:
1,PERFENH_INTRAFREQ_MC_TMPLT_SWITCH:
1,PERFENH_INTERRAT_PENALTY_50_SWITCH:
1,PERFENH_SRB_OVER_HSUPA_TTI10_SWITC
H:
0,PERFENH_HSUPA_TTI2_ENHANCE_SWITCH:
0,PERFENH_UU_P2D_CUC_OPT_SWITCH:
0,PERFENH_RL_RECFG_SIR_CONSIDER_SWITC
H:1,PERFENH_RRC_REDIR_PROTECT_SWITCH:
0,PERFENH_H2F_OPT_SWITCH:
0,PERFENH_PSTRAFFIC_P2H_SWITCH:
0,PERFENH_VIP_USER_PCHR_MR_SWITCH:
0,PERFENH_TX_INTERRUPT_AFT_TRIG_SWITC
H:
0,PERFENH_CELL_HSUPA_CAP_CHANGE_OPT
_SWITCH:0,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWI
TCH:
0,PERFENH_DOWNLOAD_ENHANCE_SWITCH:
0,PERFENH_OLPC_BLER_COEF_ADJUST:
1,PERFENH_EMG_AGPS_MC_DELAY_SWITCH:
0,PERFENH_MULTI_RLS_CQI_PARA_OPT_SWIT
CH:
0,PERFENH_RELOC_IE_CALCTIMEFORCIP_SWI
TCH:
0,PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH:
0,PERFENH_CELL_CACLOAD_BROADCAST_A
MEND:
1,PERFENH_MBDR_TARCELLSEL_OPT_SWITC
H:
0,PERFENH_RRC_DRD_PREADMISSION_SWITC
H:0,PERFENH_RRC_WEAK_REDIR_SWITCH:
0,PERFENH_L2U_CSFB_COMMCALL_SWITCH:
0,PERFENH_DLBLINDDETECT_WHEN_ON-
LYSRBONDCH:
0,PERFENH_DLBLINDDETECT_WHEN_SRBAM-
RONDCH:
0,PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIM-
IT:0
HSUPA BSC690 SET WRFD- HSDPA Meaning: Event 4A threshold for HSUPA throughput
4AThro 0 UUEST 0106111 State measurement in the optimized H2F state transition
uThd ATETR 1 Transiti algorithm. H2F state transition is a state transition of
ANS on HSPA UEs from CELL_DCH to CELL_FACH. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: 0~384
Unit: kbit/s
Actual Value Range: 0~384
Default Value: 64
HSUPA BSC691 SET WRFD- HSDPA Meaning: Event 4A threshold for HSUPA throughput
4AThro 0 UUEST 0106111 State measurement in the optimized H2F state transition
uThd ATETR 1 Transiti algorithm. H2F state transition is a state transition of
ANS on HSPA UEs from CELL_DCH to CELL_FACH. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: 0~384
Unit: kbit/s
Actual Value Range: 0~384
Default Value: 64
HSDPA BSC690 SET WRFD- HSDPA Meaning: Event 4A threshold for HSDPA traffic
4ATvm 0 UUEST 0106111 State measurement in the optimized H2F state transition
Thd ATETR 1 Transiti algorithm. H2F state transition is a state transition of
ANS on HSPA UEs from CELL_DCH to CELL_FACH. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: D8, D16, D32, D64, D128, D256,
D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
D24k, D32k, D48k, D64k, D96k, D128k, D192k,
D256k, D384k, D512k
Unit: byte
Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k
Default Value: D1024
HSDPA BSC691 SET WRFD- HSDPA Meaning: Event 4A threshold for HSDPA traffic
4ATvm 0 UUEST 0106111 State measurement in the optimized H2F state transition
Thd ATETR 1 Transiti algorithm. H2F state transition is a state transition of
ANS on HSPA UEs from CELL_DCH to CELL_FACH. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: D8, D16, D32, D64, D128, D256,
D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
D24k, D32k, D48k, D64k, D96k, D128k, D192k,
D256k, D384k, D512k
Unit: byte
Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k
Default Value: D1024
PERFENH_AMRC_DELAY_UE_COMP_SWITCH:
Scope of UEs on which adjusting the uplink rate using
AMRC is delayed. When this switch is turned off, the
algorithm for delaying adjusting the uplink rate using
AMRC can be enabled on all UEs. When this switch is
turned on, the scope of UEs is set by running the "ADD
UIMEITAC" command. In this case, the CN must
support CS IMEI query. 30.
PERFENH_SMLC_D2F_ALLOW_SWITCH:
Whether to allow state transition from CELL_FACH to
CELL_DCH and a location measurement control
message to be sent to the UE when the RNC receives a
RANAP Location Reporting Control message from the
CN and the DRA_PS_BE_STATE_TRANS_SWITCH
switch is turned off. When this switch is turned off, state
transition from CELL_FACH to CELL_DCH is not
allowed and the RNC does not send a location
measurement control message to the UE. When the
switch is turned on, state transition from CELL_FACH
to CELL_DCH is allowed and the RNC sends a location
measurement control message to the UE after state
transition is successful. 31.
PERFENH_CSPS_NO_RATEUP_IN_CONJ_SWITC
H: Whether the RNC prohibits the PS RB
reconfiguration triggered by an uplink or downlink
event 4A measurement report if the status is congested
as indicated by Combined Service Power Resource
Congest State. When this switch is turned off, the RNC
allows the PS RB reconfiguration triggered by an event
4A measurement report. When this switch is turned on,
the RNC prohibits the PS RB reconfiguration triggered
by an uplink or downlink event 4A measurement report
if the status is congested as indicated by Combined
Service Power Resource Congest State. 32.
PERFENH_UE_LTE_MEAS_CAP_SWITCH:
Whether to parse E-UTRAN measurement capabilities
by protocols. As specified by protocols, all UTRAN
frequency bands supported by a UE have the same E-
UTRAN measurement capability. When this switch is
turned on, the E-UTRAN measurement capability
carried in the IE "UE-RadioAccessCapabBandFDD3"
applies to all UTRAN frequency bands supported by the
UE. When this switch is turned off, the E-UTRAN
measurement capability carried in the IE "UE-
RadioAccessCapabBandFDD3" applies only to the
frequency band serving the UE.
PERFENH_FACH_CONG_D2IDLE_SWITCH,
PERFENH_P2D_FAIL_RETRY_SWITCH,
PERFENH_PTT_IUR_D2F_SWITCH,
PERFENH_LOW_VELO_OPT_SWITCH,
PERFENH_SRB_FAST_HRETRY_AFTER_DRD_S
WITCH, PERFENH_PTT_H2F_OPT_SWITCH,
PERFENH_IUR_DB_TICK_OPT_SWITCH,
PERFENH_P2D_LIMIT_ON_DCH_LOWRATE_S
WITCH,
PERFENH_BASE_RES_BE_TTI_DELAY_SWITCH
,
PERFENH_BASE_ADM_CE_TTI2MS_LIMIT_SWI
TCH,
PERFENH_OLPC_SIRTAR_RESEND_SWITCH,
PERFENH_F2P_LIMIT_WITH_CS_IU_CON_SWIT
CH,
PERFENH_CS_PS_F2H_RATE_LIMIT_SWITCH,
PERFENH_TTI_MC_UPDATE_OPT_SWITCH,
PERFENH_HRETRY_OPT_WITH_CM_SWITCH,
PERFENH_UL_CHL_CHG_OLPC_OPT_SWITCH,
PERFENH_IUR_CSPS_COMB_OPT_SWITCH,
PERFENH_GSMOPGRP_TRANSTOSRNC_SWITC
H, PERFENH_INTERRATHO_RETRY_SWITCH,
PERFENH_ICR_GSMNCELL_FILTER_SWITCH,
PERFENH_AMRC_DELAY_SWITCH,
PERFENH_AMRC_DELAY_UE_COMP_SWITCH,
PERFENH_SMLC_D2F_ALLOW_SWITCH,
PERFENH_CSPS_NO_RATEUP_IN_CONJ_SWITC
H, PERFENH_UE_LTE_MEAS_CAP_SWITCH
Default Value:
PERFENH_HSUPA_LOC_BASED_SCHEDUL_SW
ITCH:0,PERFENH_HRETRY_OPT_SWITCH:
1,PERFENH_IUR_CSPS_RELOC_OPT_SWITCH:
0,PERFENH_HSUPA_PO_THROU_MEAS_OPT_S
WITCH:1,PERFENH_OLPC_BLER_COEF_AD-
JUSTOPT:
0,PERFENH_LITTLE_RATE_TIMER_AMEND:
1,PERFENH_CS_TRIG_PS_P2D_ZERO_SWITCH:
0,PERFENH_FACH_CONG_D2IDLE_SWITCH:
0,PERFENH_P2D_FAIL_RETRY_SWITCH:
1,PERFENH_PTT_IUR_D2F_SWITCH:
0,PERFENH_LOW_VELO_OPT_SWITCH:
0,PERFENH_SRB_FAST_HRETRY_AFTER_DRD_
SWITCH:0,PERFENH_PTT_H2F_OPT_SWITCH:
1,PERFENH_IUR_DB_TICK_OPT_SWITCH:
1,PERFENH_P2D_LIMIT_ON_DCH_LOWRATE_S
PERFENH_AMRC_DELAY_UE_COMP_SWITCH:
Scope of UEs on which adjusting the uplink rate using
AMRC is delayed. When this switch is turned off, the
algorithm for delaying adjusting the uplink rate using
AMRC can be enabled on all UEs. When this switch is
turned on, the scope of UEs is set by running the "ADD
UIMEITAC" command. In this case, the CN must
support CS IMEI query. 30.
PERFENH_SMLC_D2F_ALLOW_SWITCH:
Whether to allow state transition from CELL_FACH to
CELL_DCH and a location measurement control
message to be sent to the UE when the RNC receives a
RANAP Location Reporting Control message from the
CN and the DRA_PS_BE_STATE_TRANS_SWITCH
switch is turned off. When this switch is turned off, state
transition from CELL_FACH to CELL_DCH is not
allowed and the RNC does not send a location
measurement control message to the UE. When the
switch is turned on, state transition from CELL_FACH
to CELL_DCH is allowed and the RNC sends a location
measurement control message to the UE after state
transition is successful. 31.
PERFENH_CSPS_NO_RATEUP_IN_CONJ_SWITC
H: Whether the RNC prohibits the PS RB
reconfiguration triggered by an uplink or downlink
event 4A measurement report if the status is congested
as indicated by Combined Service Power Resource
Congest State. When this switch is turned off, the RNC
allows the PS RB reconfiguration triggered by an event
4A measurement report. When this switch is turned on,
the RNC prohibits the PS RB reconfiguration triggered
by an uplink or downlink event 4A measurement report
if the status is congested as indicated by Combined
Service Power Resource Congest State. 32.
PERFENH_UE_LTE_MEAS_CAP_SWITCH:
Whether to parse E-UTRAN measurement capabilities
by protocols. As specified by protocols, all UTRAN
frequency bands supported by a UE have the same E-
UTRAN measurement capability. When this switch is
turned on, the E-UTRAN measurement capability
carried in the IE "UE-RadioAccessCapabBandFDD3"
applies to all UTRAN frequency bands supported by the
UE. When this switch is turned off, the E-UTRAN
measurement capability carried in the IE "UE-
RadioAccessCapabBandFDD3" applies only to the
frequency band serving the UE.
PERFENH_FACH_CONG_D2IDLE_SWITCH,
PERFENH_P2D_FAIL_RETRY_SWITCH,
PERFENH_PTT_IUR_D2F_SWITCH,
PERFENH_LOW_VELO_OPT_SWITCH,
PERFENH_SRB_FAST_HRETRY_AFTER_DRD_S
WITCH, PERFENH_PTT_H2F_OPT_SWITCH,
PERFENH_IUR_DB_TICK_OPT_SWITCH,
PERFENH_P2D_LIMIT_ON_DCH_LOWRATE_S
WITCH,
PERFENH_BASE_RES_BE_TTI_DELAY_SWITCH
,
PERFENH_BASE_ADM_CE_TTI2MS_LIMIT_SWI
TCH,
PERFENH_OLPC_SIRTAR_RESEND_SWITCH,
PERFENH_F2P_LIMIT_WITH_CS_IU_CON_SWIT
CH,
PERFENH_CS_PS_F2H_RATE_LIMIT_SWITCH,
PERFENH_TTI_MC_UPDATE_OPT_SWITCH,
PERFENH_HRETRY_OPT_WITH_CM_SWITCH,
PERFENH_UL_CHL_CHG_OLPC_OPT_SWITCH,
PERFENH_IUR_CSPS_COMB_OPT_SWITCH,
PERFENH_GSMOPGRP_TRANSTOSRNC_SWITC
H, PERFENH_INTERRATHO_RETRY_SWITCH,
PERFENH_ICR_GSMNCELL_FILTER_SWITCH,
PERFENH_AMRC_DELAY_SWITCH,
PERFENH_AMRC_DELAY_UE_COMP_SWITCH,
PERFENH_SMLC_D2F_ALLOW_SWITCH,
PERFENH_CSPS_NO_RATEUP_IN_CONJ_SWITC
H, PERFENH_UE_LTE_MEAS_CAP_SWITCH
Default Value:
PERFENH_HSUPA_LOC_BASED_SCHEDUL_SW
ITCH:0,PERFENH_HRETRY_OPT_SWITCH:
1,PERFENH_IUR_CSPS_RELOC_OPT_SWITCH:
0,PERFENH_HSUPA_PO_THROU_MEAS_OPT_S
WITCH:1,PERFENH_OLPC_BLER_COEF_AD-
JUSTOPT:
0,PERFENH_LITTLE_RATE_TIMER_AMEND:
1,PERFENH_CS_TRIG_PS_P2D_ZERO_SWITCH:
0,PERFENH_FACH_CONG_D2IDLE_SWITCH:
0,PERFENH_P2D_FAIL_RETRY_SWITCH:
1,PERFENH_PTT_IUR_D2F_SWITCH:
0,PERFENH_LOW_VELO_OPT_SWITCH:
0,PERFENH_SRB_FAST_HRETRY_AFTER_DRD_
SWITCH:0,PERFENH_PTT_H2F_OPT_SWITCH:
1,PERFENH_IUR_DB_TICK_OPT_SWITCH:
1,PERFENH_P2D_LIMIT_ON_DCH_LOWRATE_S
PTTE2F BSC690 SET WRFD- Push to Meaning: Absolute threshold for triggering event 4B
ThrouTh 0 UPTTS 020134 Talk related to the E-DCH throughput of PTT services. If the
d TATET E-DCH throughput of PTT services is lower than the
RANS threshold within a period, event 4B related to the E-
DCH throughput is triggered. The period is calculated
by multiplying the value of "PTTE2FThrouMeasPer-
iod" by the value of "PTTE2FThrouTimeToTrig".
GUI Value Range: 0~38400
Unit: 10bit/s
Actual Value Range: 0~384000
Default Value: 1
PTTE2F BSC691 SET WRFD- Push to Meaning: Absolute threshold for triggering event 4B
ThrouTh 0 UPTTS 020134 Talk related to the E-DCH throughput of PTT services. If the
d TATET E-DCH throughput of PTT services is lower than the
RANS threshold within a period, event 4B related to the E-
DCH throughput is triggered. The period is calculated
by multiplying the value of "PTTE2FThrouMeasPer-
iod" by the value of "PTTE2FThrouTimeToTrig".
GUI Value Range: 0~38400
Unit: 10bit/s
Actual Value Range: 0~384000
Default Value: 1
PTTDH BSC690 SET WRFD- Push to Meaning: Absolute threshold for triggering event 4B
2FTvmT 0 UPTTS 020134 Talk related to PTT service traffic on the DCH or HSDPA
hd TATET channel. If the PTT service traffic is continuous lower
RANS than the threshold within the time specified by
"PTTDH2FTvmTimeToTrig", event 4B is triggered.
GUI Value Range: D8, D16, D32, D64, D128, D256,
D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
D24k, D32k, D48k, D64k, D96k, D128k, D192k,
D256k, D384k, D512k, D768k
Unit: byte
Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k, 768k
Default Value: D8
PTTDH BSC691 SET WRFD- Push to Meaning: Absolute threshold for triggering event 4B
2FTvmT 0 UPTTS 020134 Talk related to PTT service traffic on the DCH or HSDPA
hd TATET channel. If the PTT service traffic is continuous lower
RANS than the threshold within the time specified by
"PTTDH2FTvmTimeToTrig", event 4B is triggered.
GUI Value Range: D8, D16, D32, D64, D128, D256,
D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
D24k, D32k, D48k, D64k, D96k, D128k, D192k,
D256k, D384k, D512k, D768k
Unit: byte
Actual Value Range: 8, 16, 32, 64, 128, 256, 512, 1024,
2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k, 768k
Default Value: D8
LittleRat BSC690 SET WRFD- Dynami Meaning: Bit rate threshold for low activity. When a BE
eThd 0 UDCCC 021101 c service's data rate is decreased to the one for DCCC and
WRFD- Channel conditions for a D2F state transition are met, the RNC
010202 Configu decreases the data rate to the one for low activity if the
ration D2F state transition cannot be performed. The reason
WRFD- Control for the failed D2F state transition can be that the switch
0106111 (DCCC) for the transition to the CELL_FACH state is turned off
1 or that CS services are going on. The traffic
UE State
in measurement control parameters and timer for adjusting
Connect the bit rate for low activity are the same as those for the
ed Mode D2F state transition. These parameters and the timer can
(CELL- be set in the "SET UUESTATETRANS" and "SET
DCH, UUESTATETRANSTIMER" commands.
CELL- GUI Value Range: D0, D8, D16, D32, D64, D128,
PCH, D144, D256, D384
URA- Unit: kbit/s
PCH,
CELL- Actual Value Range: 0, 8, 16, 32, 64, 128, 144, 256, 384
FACH) Default Value: D8
HSDPA
State
Transiti
on
LittleRat BSC691 SET WRFD- Dynami Meaning: Bit rate threshold for low activity. When a BE
eThd 0 UDCCC 021101 c service's data rate is decreased to the one for DCCC and
WRFD- Channel conditions for a D2F state transition are met, the RNC
010202 Configu decreases the data rate to the one for low activity if the
ration D2F state transition cannot be performed. The reason
WRFD- Control for the failed D2F state transition can be that the switch
0106111 (DCCC) for the transition to the CELL_FACH state is turned off
1 or that CS services are going on. The traffic
UE State
in measurement control parameters and timer for adjusting
Connect the bit rate for low activity are the same as those for the
ed Mode D2F state transition. These parameters and the timer can
(CELL- be set in the "SET UUESTATETRANS" and "SET
DCH, UUESTATETRANSTIMER" commands.
CELL- GUI Value Range: D0, D8, D16, D32, D64, D128,
PCH, D144, D256, D384
URA- Unit: kbit/s
PCH,
CELL- Actual Value Range: 0, 8, 16, 32, 64, 128, 144, 256, 384
FACH) Default Value: D8
HSDPA
State
Transiti
on
D2PPsIn BSC690 SET WRFD- UE State Meaning: PS inactivity timer for CELL_DCH-to-
actTime 0 UUEST 010202 in CELL_PCH (D2P) state transitions. This timer is used
r ATETR Connect in the PS-inactivity-based D2P state transition
ANSTI ed Mode algorithm. This algorithm triggers a D2P state transition
MER (CELL- upon detecting that a UE in the CELL_DCH state does
DCH, not process any uplink or downlink service during a
CELL- certain period of time, which is specified by this
PCH, parameter.
URA- GUI Value Range: 1~3600
PCH,
CELL- Unit: s
FACH) Actual Value Range: 1~3600
Default Value: 2
BeF2PSt BSC690 SET WRFD- UE State Meaning: Timer for state transition from FACH or
ateTrans 0 UUEST 010202 in E_FACH to PCH of BE services, used to check whether
Timer ATETR WRFD- Connect the UE in the CELL_FACH state is in the stable low
ANSTI 04010 ed Mode activity state.If this parameter is set to 65535, UEs
MER (CELL- processing BE services are not allowed to switch from
DCH, CELL_FACH or E_FACH to CELL_PCH.
CELL- GUI Value Range: 1~65535
PCH,
URA- Unit: s
PCH, Actual Value Range: 1~65535
CELL- Default Value: 65535
FACH)
BeF2PSt BSC691 SET WRFD- UE State Meaning: Timer for state transition from FACH or
ateTrans 0 UUEST 010202 in E_FACH to PCH of BE services, used to check whether
Timer ATETR WRFD- Connect the UE in the CELL_FACH state is in the stable low
ANSTI 04010 ed Mode activity state.If this parameter is set to 65535, UEs
MER (CELL- processing BE services are not allowed to switch from
DCH, CELL_FACH or E_FACH to CELL_PCH.
CELL- GUI Value Range: 1~65535
PCH,
URA- Unit: s
PCH, Actual Value Range: 1~65535
CELL- Default Value: 65535
FACH)
F2PTvm BSC690 SET WRFD- UE State Meaning: When the traffic volume is below the 4B
TimeTo 0 UUEST 010202 in threshold and remains so for the period specified by this
Trig ATETR Connect parameter, the event 4B is reported. This parameter can
ANS ed Mode prevent unnecessary reports to be triggered, caused by
(CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D5000
F2PTvm BSC691 SET WRFD- UE State Meaning: When the traffic volume is below the 4B
TimeTo 0 UUEST 010202 in threshold and remains so for the period specified by this
Trig ATETR Connect parameter, the event 4B is reported. This parameter can
ANS ed Mode prevent unnecessary reports to be triggered, caused by
(CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D5000
F2PTvm BSC690 SET WRFD- UE State Meaning: Pending time after the traffic volume event
PTAT 0 UUEST 010202 in 4B for state transition from FACH to PCH is reported.
ATETR Connect This parameter is used to prevent too many traffic
ANS ed Mode volume events 4B being reported.
(CELL- GUI Value Range: D250, D500, D1000, D2000, D4000,
DCH, D8000, D16000
CELL-
PCH, Unit: ms
URA- Actual Value Range: 250, 500, 1000, 2000, 4000, 8000,
PCH, 16000
CELL- Default Value: D1000
FACH)
F2PTvm BSC691 SET WRFD- UE State Meaning: Pending time after the traffic volume event
PTAT 0 UUEST 010202 in 4B for state transition from FACH to PCH is reported.
ATETR Connect This parameter is used to prevent too many traffic
ANS ed Mode volume events 4B being reported.
(CELL- GUI Value Range: D250, D500, D1000, D2000, D4000,
DCH, D8000, D16000
CELL-
PCH, Unit: ms
URA- Actual Value Range: 250, 500, 1000, 2000, 4000, 8000,
PCH, 16000
CELL- Default Value: D1000
FACH)
CellReS BSC690 SET WRFD- UE State Meaning: Length of the timer determining frequent cell
electTim 0 UUEST 010202 in reselections. If the number of cell reselections
er ATETR Connect performed by a UE in the CELL_PCH state during a
ANSTI ed Mode specific period is equal to or larger than the value for
MER (CELL- "CellReSelectCounter", the RNC determines that the
DCH, UE has performed frequent cell reselections. This
CELL- period is equal to the period when this timer is taking
PCH, effect. When the UE reports another cell update after the
URA- timer expires, the RNC informs the UE to enter the
PCH, URA_PCH state by sending the UE a
CELL- CELL_UPADATE_CONFIRM message.
FACH) GUI Value Range: 1~65535
Unit: s
Actual Value Range: 1~65535
Default Value: 180
CellReS BSC691 SET WRFD- UE State Meaning: Length of the timer determining frequent cell
electTim 0 UUEST 010202 in reselections. If the number of cell reselections
er ATETR Connect performed by a UE in the CELL_PCH state during a
ANSTI ed Mode specific period is equal to or larger than the value for
MER (CELL- "CellReSelectCounter", the RNC determines that the
DCH, UE has performed frequent cell reselections. This
CELL- period is equal to the period when this timer is taking
PCH, effect. When the UE reports another cell update after the
URA- timer expires, the RNC informs the UE to enter the
PCH, URA_PCH state by sending the UE a
CELL- CELL_UPADATE_CONFIRM message.
FACH) GUI Value Range: 1~65535
Unit: s
Actual Value Range: 1~65535
Default Value: 180
CellReS BSC690 SET WRFD- UE State Meaning: Threshold for the number of cell reselections.
electCou 0 UUEST 010202 in If the number of cell reselections performed by a UE in
nter ATETR Connect the CELL_PCH state during a specific period is equal
ANS ed Mode to or larger than this threshold, the RNC determines that
(CELL- the UE has performed frequent cell reselections. This
DCH, period is equal to the period when the timer determining
CELL- frequent cell reselections is taking effect. When the UE
PCH, reports another cell update after the timer expires, the
URA- RNC informs the UE to enter the URA_PCH state by
PCH, sending the UE a CELL_UPADATE_CONFIRM
CELL- message.
FACH) GUI Value Range: 1~65535
Unit: None
Actual Value Range: 1~65535
Default Value: 9
CellReS BSC691 SET WRFD- UE State Meaning: Threshold for the number of cell reselections.
electCou 0 UUEST 010202 in If the number of cell reselections performed by a UE in
nter ATETR Connect the CELL_PCH state during a specific period is equal
ANS ed Mode to or larger than this threshold, the RNC determines that
(CELL- the UE has performed frequent cell reselections. This
DCH, period is equal to the period when the timer determining
CELL- frequent cell reselections is taking effect. When the UE
PCH, reports another cell update after the timer expires, the
URA- RNC informs the UE to enter the URA_PCH state by
PCH, sending the UE a CELL_UPADATE_CONFIRM
CELL- message.
FACH) GUI Value Range: 1~65535
Unit: None
Actual Value Range: 1~65535
Default Value: 9
CS_RLFAIL_RRCSETUP_STAT_SWITCH,
PS_INACT_NOTREL_FOR_CSPS_SWITCH,
RAB_DL_BITRATE_MOD_SWITCH,
RAB_WAIT_IUUP_INIT_RESPONSE_SWITCH,
CS_CALL_DROP_DEFINITION,
PS_CALL_DROP_DEFINITION,
CCH_ABNORMOLREL_CAUSE_SWITCH,
RNC_U2U_SWITCH,
INTERRAT2U_RESUME_PS_ASAP_SWITCH,
UE_TRB_RESET_IOT_SWITCH,
CUC_CMP_NO_ACTIVE_CFN_SWITCH,
RNC_RDY_FOR_INTERRAT_COMPATIBLE_SWI
TCH
Unit: None
Actual Value Range:
FACH_DCCH_CONG_CTRL_SWITCH,
RNC_F2D_RLC_SUSPEND_SWITCH,
UM_RRCRELCMP_RLDEL_DELAY_SWITCH,
RNC_TVM_BASED_P2D_SWITCH,
CS_RLFAIL_RRCSETUP_STAT_SWITCH,
PS_INACT_NOTREL_FOR_CSPS_SWITCH,
RAB_DL_BITRATE_MOD_SWITCH,
RAB_WAIT_IUUP_INIT_RESPONSE_SWITCH,
CS_CALL_DROP_DEFINITION,
PS_CALL_DROP_DEFINITION,
CCH_ABNORMOLREL_CAUSE_SWITCH,
RNC_U2U_SWITCH,
INTERRAT2U_RESUME_PS_ASAP_SWITCH,
UE_TRB_RESET_IOT_SWITCH,
CUC_CMP_NO_ACTIVE_CFN_SWITCH,
RNC_RDY_FOR_INTERRAT_COMPATIBLE_SWI
TCH
Default Value:
FACH_DCCH_CONG_CTRL_SWITCH:
0,RNC_F2D_RLC_SUSPEND_SWITCH:
0,UM_RRCRELCMP_RLDEL_DELAY_SWITCH:
1,RNC_TVM_BASED_P2D_SWITCH:
0,CS_RLFAIL_RRCSETUP_STAT_SWITCH:
0,PS_INACT_NOTREL_FOR_CSPS_SWITCH:
0,RAB_DL_BITRATE_MOD_SWITCH:
0,RAB_WAIT_IUUP_INIT_RESPONSE_SWITCH:
0,CS_CALL_DROP_DEFINITION:
0,PS_CALL_DROP_DEFINITION:
0,CCH_ABNORMOLREL_CAUSE_SWITCH:
0,RNC_U2U_SWITCH:
0,INTERRAT2U_RESUME_PS_ASAP_SWITCH:
0,UE_TRB_RESET_IOT_SWITCH:
0,CUC_CMP_NO_ACTIVE_CFN_SWITCH:
0,RNC_RDY_FOR_INTERRAT_COMPATIBLE_S
WITCH:0
CS_RLFAIL_RRCSETUP_STAT_SWITCH,
PS_INACT_NOTREL_FOR_CSPS_SWITCH,
RAB_DL_BITRATE_MOD_SWITCH,
RAB_WAIT_IUUP_INIT_RESPONSE_SWITCH,
CS_CALL_DROP_DEFINITION,
PS_CALL_DROP_DEFINITION,
CCH_ABNORMOLREL_CAUSE_SWITCH,
RNC_U2U_SWITCH,
INTERRAT2U_RESUME_PS_ASAP_SWITCH,
UE_TRB_RESET_IOT_SWITCH,
CUC_CMP_NO_ACTIVE_CFN_SWITCH,
RNC_RDY_FOR_INTERRAT_COMPATIBLE_SWI
TCH
Unit: None
Actual Value Range:
FACH_DCCH_CONG_CTRL_SWITCH,
RNC_F2D_RLC_SUSPEND_SWITCH,
UM_RRCRELCMP_RLDEL_DELAY_SWITCH,
RNC_TVM_BASED_P2D_SWITCH,
CS_RLFAIL_RRCSETUP_STAT_SWITCH,
PS_INACT_NOTREL_FOR_CSPS_SWITCH,
RAB_DL_BITRATE_MOD_SWITCH,
RAB_WAIT_IUUP_INIT_RESPONSE_SWITCH,
CS_CALL_DROP_DEFINITION,
PS_CALL_DROP_DEFINITION,
CCH_ABNORMOLREL_CAUSE_SWITCH,
RNC_U2U_SWITCH,
INTERRAT2U_RESUME_PS_ASAP_SWITCH,
UE_TRB_RESET_IOT_SWITCH,
CUC_CMP_NO_ACTIVE_CFN_SWITCH,
RNC_RDY_FOR_INTERRAT_COMPATIBLE_SWI
TCH
Default Value:
FACH_DCCH_CONG_CTRL_SWITCH:
0,RNC_F2D_RLC_SUSPEND_SWITCH:
0,UM_RRCRELCMP_RLDEL_DELAY_SWITCH:
1,RNC_TVM_BASED_P2D_SWITCH:
0,CS_RLFAIL_RRCSETUP_STAT_SWITCH:
0,PS_INACT_NOTREL_FOR_CSPS_SWITCH:
0,RAB_DL_BITRATE_MOD_SWITCH:
0,RAB_WAIT_IUUP_INIT_RESPONSE_SWITCH:
0,CS_CALL_DROP_DEFINITION:
0,PS_CALL_DROP_DEFINITION:
0,CCH_ABNORMOLREL_CAUSE_SWITCH:
0,RNC_U2U_SWITCH:
0,INTERRAT2U_RESUME_PS_ASAP_SWITCH:
0,UE_TRB_RESET_IOT_SWITCH:
0,CUC_CMP_NO_ACTIVE_CFN_SWITCH:
0,RNC_RDY_FOR_INTERRAT_COMPATIBLE_S
WITCH:0
BeF2DT BSC690 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
vmThd 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
ATETR Connect of BE services from FACH to DCH.
ANS ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
(CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
CELL- D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
Default Value: D256
BeF2DT BSC691 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
vmThd 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
ATETR Connect of BE services from FACH to DCH.
ANS ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
(CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
CELL- D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
Default Value: D256
BeF2DT BSC690 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
vmTime 0 UUEST 010202 in of 4A event for triggering the transition of BE services
ToTrig ATETR Connect from FACH to DCH. This parameter can prevent
ANS ed Mode unnecessary reports to be triggered, caused by traffic
(CELL- volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D0
BeF2DT BSC691 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
vmTime 0 UUEST 010202 in of 4A event for triggering the transition of BE services
ToTrig ATETR Connect from FACH to DCH. This parameter can prevent
ANS ed Mode unnecessary reports to be triggered, caused by traffic
(CELL- volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D0
BeF2HT BSC690 SET WRFD- HSDPA Meaning: This parameter specifies the threshold of the
vmThd 0 UUEST 0106111 State traffic volume of 4A event for triggering the transition
ATETR 1 Transiti of BE services from FACH to HS-DSCH.
ANS on GUI Value Range: D16, D32, D64, D128, D256, D512,
D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
D32k, D48k, D64k, D96k, D128k, D192k, D256k,
D384k, D512k, D768k
Unit: byte
Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k, 768k
Default Value: D256
BeF2HT BSC691 SET WRFD- HSDPA Meaning: This parameter specifies the threshold of the
vmThd 0 UUEST 0106111 State traffic volume of 4A event for triggering the transition
ATETR 1 Transiti of BE services from FACH to HS-DSCH.
ANS on GUI Value Range: D16, D32, D64, D128, D256, D512,
D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
D32k, D48k, D64k, D96k, D128k, D192k, D256k,
D384k, D512k, D768k
Unit: byte
Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
128k, 192k, 256k, 384k, 512k, 768k
Default Value: D256
BeF2HT BSC690 SET WRFD- HSDPA Meaning: This parameter specifies the occurrence time
vmTime 0 UUEST 0106111 State of 4A event for triggering the transition of BE services
ToTrig ATETR 1 Transiti from FACH to HS-DSCH. This parameter can prevent
ANS on unnecessary reports to be triggered, caused by traffic
volume variation.
GUI Value Range: D0, D10, D20, D40, D60, D80,
D100, D120, D160, D200, D240, D320, D640, D1280,
D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
200, 240, 320, 640, 1280, 2560, 5000
Default Value: D0
BeF2HT BSC691 SET WRFD- HSDPA Meaning: This parameter specifies the occurrence time
vmTime 0 UUEST 0106111 State of 4A event for triggering the transition of BE services
ToTrig ATETR 1 Transiti from FACH to HS-DSCH. This parameter can prevent
ANS on unnecessary reports to be triggered, caused by traffic
volume variation.
GUI Value Range: D0, D10, D20, D40, D60, D80,
D100, D120, D160, D200, D240, D320, D640, D1280,
D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
200, 240, 320, 640, 1280, 2560, 5000
Default Value: D0
EdchRat BSC690 SET WRFD- Dynami Meaning: Data rate set for adjusting the EDCH's data
eAdjust 0 UEDCH 021101 c rate. The DCCC function can allocate any data rate in
Set RATEA WRFD- Channel such a data rate set to an EDCH.
DJUSTS 0106120 Configu GUI Value Range: RATE_8KBPS, RATE_16KBPS,
ET 8 ration RATE_32KBPS, RATE_64KBPS, RATE_128KBPS,
Control RATE_144KBPS, RATE_256KBPS,
(DCCC) RATE_384KBPS, RATE_608KBPS,
HSUPA RATE_1280KBPS, RATE_2048KBPS,
DCCC RATE_2720KBPS, RATE_5440KBPS,
RATE_11480KBPS
Unit: None
Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384,
608, 1280, 2048, 2720, 5440, 11480
Default Value: RATE_8KBPS:0,RATE_16KBPS:
0,RATE_32KBPS:0,RATE_64KBPS:
0,RATE_128KBPS:1,RATE_144KBPS:
0,RATE_256KBPS:1,RATE_384KBPS:
0,RATE_608KBPS:1,RATE_1280KBPS:
0,RATE_2048KBPS:0,RATE_2720KBPS:
0,RATE_5440KBPS:0,RATE_11480KBPS:0
EdchRat BSC691 SET WRFD- Dynami Meaning: Data rate set for adjusting the EDCH's data
eAdjust 0 UEDCH 021101 c rate. The DCCC function can allocate any data rate in
Set RATEA WRFD- Channel such a data rate set to an EDCH.
DJUSTS 0106120 Configu GUI Value Range: RATE_8KBPS, RATE_16KBPS,
ET 8 ration RATE_32KBPS, RATE_64KBPS, RATE_128KBPS,
Control RATE_144KBPS, RATE_256KBPS,
(DCCC) RATE_384KBPS, RATE_608KBPS,
HSUPA RATE_1280KBPS, RATE_2048KBPS,
DCCC RATE_2720KBPS, RATE_5440KBPS,
RATE_11480KBPS
Unit: None
Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384,
608, 1280, 2048, 2720, 5440, 11480
Default Value: RATE_8KBPS:0,RATE_16KBPS:
0,RATE_32KBPS:0,RATE_64KBPS:
0,RATE_128KBPS:1,RATE_144KBPS:
0,RATE_256KBPS:1,RATE_384KBPS:
0,RATE_608KBPS:1,RATE_1280KBPS:
0,RATE_2048KBPS:0,RATE_2720KBPS:
0,RATE_5440KBPS:0,RATE_11480KBPS:0
RtF2DH BSC690 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
TvmThd 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
ATETR Connect of real-time services from FACH to DCH or HSPA.
ANS ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
(CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
CELL- D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
Default Value: D1024
RtF2DH BSC691 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
TvmThd 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
ATETR Connect of real-time services from FACH to DCH or HSPA.
ANS ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
(CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
CELL- D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
Default Value: D1024
RtF2DH BSC690 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
TvmTim 0 UUEST 010202 in of 4A event for triggering the transition of real-time
eToTrig ATETR Connect services from FACH to DCH or HSPA. This parameter
ANS ed Mode can prevent unnecessary reports to be triggered, caused
(CELL- by traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D240
RtF2DH BSC691 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
TvmTim 0 UUEST 010202 in of 4A event for triggering the transition of real-time
eToTrig ATETR Connect services from FACH to DCH or HSPA. This parameter
ANS ed Mode can prevent unnecessary reports to be triggered, caused
(CELL- by traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D240
BeF2ET BSC690 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
vmThd 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
ATETR Connect of BE services from FACH to E-DCH.
ANS ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
(CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
CELL- D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
Default Value: D1024
BeF2ET BSC691 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
vmThd 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
ATETR Connect of BE services from FACH to E-DCH.
ANS ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
(CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
CELL- D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
Default Value: D1024
BeF2ET BSC690 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
vmTime 0 UUEST 010202 in of 4A event for triggering the transition of BE services
ToTrig ATETR Connect from FACH to E-DCH. This parameter can prevent
ANS ed Mode unnecessary reports to be triggered, caused by traffic
(CELL- volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D0
BeF2ET BSC691 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
vmTime 0 UUEST 010202 in of 4A event for triggering the transition of BE services
ToTrig ATETR Connect from FACH to E-DCH. This parameter can prevent
ANS ed Mode unnecessary reports to be triggered, caused by traffic
(CELL- volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
CELL- D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
Default Value: D0
BeF2D BSC690 SET WRFD- UE State Meaning: FACH load threshold for triggering reporting
HTvmT 0 UUEST 010202 in of event 4A for BE services. When this threshold is
hdForF ATETR Connect exceeded, the UE reports event 4A and then the RNC
ACHCo ANS ed Mode transits the UE from CELL_FACH to CELL_DCH.
ng (CELL- This parameter must be used with
DCH, "BE_4A_THD_ADJ_FOR_FACH_CONG_SWITCH
CELL- " in the "ADD UCELLDCCC" command.
PCH, GUI Value Range: D16, D32, D64, D128, D256, D512,
URA- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
PCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
CELL- D384k, D512k, D768k
FACH)
Unit: byte
Actual Value Range: D16, D32, D64, D128, D256,
D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
D24k, D32k, D48k, D64k, D96k, D128k, D192k,
D256k, D384k, D512k, D768k
Default Value: D256
BeF2D BSC691 SET WRFD- UE State Meaning: FACH load threshold for triggering reporting
HTvmT 0 UUEST 010202 in of event 4A for BE services. When this threshold is
hdForF ATETR Connect exceeded, the UE reports event 4A and then the RNC
ACHCo ANS ed Mode transits the UE from CELL_FACH to CELL_DCH.
ng (CELL- This parameter must be used with
DCH, "BE_4A_THD_ADJ_FOR_FACH_CONG_SWITCH
CELL- " in the "ADD UCELLDCCC" command.
PCH, GUI Value Range: D16, D32, D64, D128, D256, D512,
URA- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
PCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
CELL- D384k, D512k, D768k
FACH)
Unit: byte
Actual Value Range: D16, D32, D64, D128, D256,
D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k,
D24k, D32k, D48k, D64k, D96k, D128k, D192k,
D256k, D384k, D512k, D768k
Default Value: D256
TimerPo BSC690 ADD WRFD- Logical Meaning: Maximum time of waiting for the response
ll 0 UTYPS 020900 Channel from the peer end after the TX end of the AM RCL entity
RBRLC Manage sends a polling PDU. This parameter is valid only when
MOD ment the TX end is configured with polling. The timer starts
UTYPS after the TX end sends a polling PDU. The TX end
RBRLC retransmits the polling PDU after the timer expires if it
does not receive the response and restarts this timer. For
details about this parameter, see 3GPP TS 25.322. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: D10, D20, D30, D40, D50, D60,
D70, D80, D90, D100, D110, D120, D130, D140,
D150, D160, D170, D180, D190, D200, D210, D220,
D230, D240, D250, D260, D270, D280, D290, D300,
D310, D320, D330, D340, D350, D360, D370, D380,
D390, D400, D410, D420, D430, D440, D450, D460,
D470, D480, D490, D500, D510, D520, D530, D540,
D550, D600, D650, D700, D750, D800, D850, D900,
D950, D1000, NOTUSED
Unit: ms
Actual Value Range: 10, 20, 30, 40, 50, 60, 70, 80, 90,
100, 110, 120, 130, 140, 150, 160, 170, 180, 190, 200,
210, 220, 230, 240, 250, 260, 270, 280, 290, 300, 310,
320, 330, 340, 350, 360, 370, 380, 390, 400, 410, 420,
430, 440, 450, 460, 470, 480, 490, 500, 510, 520, 530,
540, 550, 600, 650, 700, 750, 800, 850, 900, 950, 1000
Default Value: None
TimerPo BSC691 ADD WRFD- Logical Meaning: Maximum time of waiting for the response
ll 0 UTYPS 020900 Channel from the peer end after the TX end of the AM RCL entity
RBRLC Manage sends a polling PDU. This parameter is valid only when
MOD ment the TX end is configured with polling. The timer starts
UTYPS after the TX end sends a polling PDU. The TX end
RBRLC retransmits the polling PDU after the timer expires if it
does not receive the response and restarts this timer. For
details about this parameter, see 3GPP TS 25.322. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: D10, D20, D30, D40, D50, D60,
D70, D80, D90, D100, D110, D120, D130, D140,
D150, D160, D170, D180, D190, D200, D210, D220,
D230, D240, D250, D260, D270, D280, D290, D300,
D310, D320, D330, D340, D350, D360, D370, D380,
D390, D400, D410, D420, D430, D440, D450, D460,
D470, D480, D490, D500, D510, D520, D530, D540,
D550, D600, D650, D700, D750, D800, D850, D900,
D950, D1000, NOTUSED
Unit: ms
Actual Value Range: 10, 20, 30, 40, 50, 60, 70, 80, 90,
100, 110, 120, 130, 140, 150, 160, 170, 180, 190, 200,
210, 220, 230, 240, 250, 260, 270, 280, 290, 300, 310,
320, 330, 340, 350, 360, 370, 380, 390, 400, 410, 420,
430, 440, 450, 460, 470, 480, 490, 500, 510, 520, 530,
540, 550, 600, 650, 700, 750, 800, 850, 900, 950, 1000
Default Value: None
RsvU8P BSC690 SET None None Meaning: RRM algorithm reserved U8 para 18. The
ara18 0 UALGO para of 8 bits is reserved for further change request use.
RSVPA Disuse statement: This parameter is used temporarily in
RA patch versions and will be replaced with a new
parameter in later versions. The new parameter ID
reflects the parameter function. Therefore, this
parameter is not recommended for the configuration
interface.
GUI Value Range: 0~255
Unit: None
Actual Value Range: 0~255
Default Value: 0
BasedTi BSC690 SET None None Meaning: Coefficient for the number of RLC
meF2D 0 UUEST retransmissions for the F2D state transition based on
RlcRetr ATETR data transmission wait time. If this parameter is set to 0,
NumCo ANS the F2D state transition based on data transmission wait
ef time does not consider RLC retransmissions. If this
parameter is set to other values, the F2D state transition
based on data transmission wait time considers RLC
retransmissions. That is, if the maximum number of
PDU retransmissions is greater than or equal to the
threshold for the number of retransmissions, the F2D
state transition is not triggered. Otherwise, the F2D state
transition is triggered. Note: 1. The threshold for the
number of retransmissions is the rounded-up value that
is calculated using the following formula: ROUNDUP
(BasedTimeF2DThd/TimerPoll x Coefficient for the
number of RLC retransmissions for the F2D state
transition based on data transmission wait time). 2. F2D
refers to the state transition from CELL_FACH to
CELL_DCH.
GUI Value Range: 0~10
Unit: None
Actual Value Range: 0~1
Default Value: 4
BasedTi BSC691 SET None None Meaning: Coefficient for the number of RLC
meF2D 0 UUEST retransmissions for the F2D state transition based on
RlcRetr ATETR data transmission wait time. If this parameter is set to 0,
NumCo ANS the F2D state transition based on data transmission wait
ef time does not consider RLC retransmissions. If this
parameter is set to other values, the F2D state transition
based on data transmission wait time considers RLC
retransmissions. That is, if the maximum number of
PDU retransmissions is greater than or equal to the
threshold for the number of retransmissions, the F2D
state transition is not triggered. Otherwise, the F2D state
transition is triggered. Note: 1. The threshold for the
number of retransmissions is the rounded-up value that
is calculated using the following formula: ROUNDUP
(BasedTimeF2DThd/TimerPoll x Coefficient for the
number of RLC retransmissions for the F2D state
transition based on data transmission wait time). 2. F2D
refers to the state transition from CELL_FACH to
CELL_DCH.
GUI Value Range: 0~10
Unit: None
Actual Value Range: 0~1
Default Value: 4
BasedTi BSC690 SET None None Meaning: Pending time for the F2D state transition
meF2DP 0 UUEST based on data transmission wait time. If the F2D state
TAT ATETR transition triggered by the F2D state transition based on
ANS data transmission wait time fails, the RNC makes a
decision for another F2D state transition based on data
transmission wait time only after the pending time
elapses.
GUI Value Range: 0~15
Unit: s
Actual Value Range: 0~15
Default Value: 2
BasedTi BSC691 SET None None Meaning: Pending time for the F2D state transition
meF2DP 0 UUEST based on data transmission wait time. If the F2D state
TAT ATETR transition triggered by the F2D state transition based on
ANS data transmission wait time fails, the RNC makes a
decision for another F2D state transition based on data
transmission wait time only after the pending time
elapses.
GUI Value Range: 0~15
Unit: s
Actual Value Range: 0~15
Default Value: 2
RsvU8P BSC691 SET None None Meaning: RRM algorithm reserved U8 para 18. The
ara18 0 UALGO para of 8 bits is reserved for further change request use.
RSVPA Disuse statement: This parameter is used temporarily in
RA patch versions and will be replaced with a new
parameter in later versions. The new parameter ID
reflects the parameter function. Therefore, this
parameter is not recommended for the configuration
interface.
GUI Value Range: 0~255
Unit: None
Actual Value Range: 0~255
Default Value: 0
command. 13.
DRA_INTELL_STATE_TRANS_ON_LOAD_SWIT
CH: Whether to validate the load based intelligent state
transition algorithm. When this switch is set to on and
the
DRA_INTELL_STATE_TRANS_ON_LOAD_SWIT
CH under the "DraSwitch" parameter in the "ADD
UCELLDCCC" command is set to on, the RNC
performs state transition according to the following
parameters: "HiLdBeD2FStateTransTimer" in the
"SET UUESTATETRANSTIMER" command,
"HiLdCellDchPSInactTimer" in the "SET
UPSINACTTIMER" command, and
"HiLdBeDLF2DHTvmThd" and
"HiLdBeULF2DETvmThd" in the "SET
UUESTATETRANS" command. 14.
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH:
Whether the coverage-based and load-based algorithm
for dynamic reconfiguration of the channel mapped to
downlink signaling radio bearers (SRBs) takes
effect.When this switch is turned off, the algorithm does
not take effect. When this switch is turned on, The
algorithm takes effect. Operations of the algorithm: 1.
Access mode: The algorithm also considers coverage
and loads to determine whether the downlink SRBs can
be carried on the HS-DSCH when a UE transits from
the idle, CELL_FACH, CELL_PCH, or URA_PCH
state to the CELL_DCH state during an RRC connection
setup, RAB setup, or RAB modification or when a
CELL_DCH UE experiences an incoming inter-RAT
handover or an incoming combined hard handover and
SRNS relocation. 2. Connected mode: After a UE
accesses a cell, the algorithm determines whether to
deliver periodic RSCP and Ec/N0 measurement control
messages. When the RNC receives periodic
measurement reports on the RSCP and Ec/N0, the
algorithm determines whether to initiate the SRB
reconfiguration process.
GUI Value Range:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SW
ITCH,
DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWIT
CH,
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH
, DRA_BASE_COVER_BE_E2D_SWITCH,
DRA_D2F_OVER_IUR_SWITCH,
DRA_CSPS_0K_RATE_UP_SWITCH,
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH,
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWIT
CH, DRA_BASE_COVER_E2D_DCCC_SWITCH,
DRA_WEB_FACH_DELAY_OPT_SWITCH,
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH,
DRA_D2P_WHEN_PS_INACT_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWIT
CH,
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH
Unit: None
Actual Value Range:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SW
ITCH,
DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWIT
CH,
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH
, DRA_BASE_COVER_BE_E2D_SWITCH,
DRA_D2F_OVER_IUR_SWITCH,
DRA_CSPS_0K_RATE_UP_SWITCH,
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH,
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWIT
CH, DRA_BASE_COVER_E2D_DCCC_SWITCH,
DRA_WEB_FACH_DELAY_OPT_SWITCH,
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH,
DRA_D2P_WHEN_PS_INACT_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWIT
CH,
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH
Default Value:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SW
ITCH:
0,DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWI
TCH:
0,DRA_BASE_COVER_BE_E2D_INITSEL_SWITC
H:0,DRA_BASE_COVER_BE_E2D_SWITCH:
0,DRA_D2F_OVER_IUR_SWITCH:
0,DRA_CSPS_0K_RATE_UP_SWITCH:
1,DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH:
0,DRA_PS_STATE_TRANS_WHEN_CS_REL_SWI
TCH:
0,DRA_BASE_COVER_E2D_DCCC_SWITCH:
0,DRA_WEB_FACH_DELAY_OPT_SWITCH:
0,DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH
:0,DRA_D2P_WHEN_PS_INACT_SWITCH:
0,DRA_INTELL_STATE_TRANS_ON_LOAD_SWI
TCH:
0,DRA_BASE_COVER_LOAD_SRB_H2D_SWITC
H:0
command. 13.
DRA_INTELL_STATE_TRANS_ON_LOAD_SWIT
CH: Whether to validate the load based intelligent state
transition algorithm. When this switch is set to on and
the
DRA_INTELL_STATE_TRANS_ON_LOAD_SWIT
CH under the "DraSwitch" parameter in the "ADD
UCELLDCCC" command is set to on, the RNC
performs state transition according to the following
parameters: "HiLdBeD2FStateTransTimer" in the
"SET UUESTATETRANSTIMER" command,
"HiLdCellDchPSInactTimer" in the "SET
UPSINACTTIMER" command, and
"HiLdBeDLF2DHTvmThd" and
"HiLdBeULF2DETvmThd" in the "SET
UUESTATETRANS" command. 14.
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH:
Whether the coverage-based and load-based algorithm
for dynamic reconfiguration of the channel mapped to
downlink signaling radio bearers (SRBs) takes
effect.When this switch is turned off, the algorithm does
not take effect. When this switch is turned on, The
algorithm takes effect. Operations of the algorithm: 1.
Access mode: The algorithm also considers coverage
and loads to determine whether the downlink SRBs can
be carried on the HS-DSCH when a UE transits from
the idle, CELL_FACH, CELL_PCH, or URA_PCH
state to the CELL_DCH state during an RRC connection
setup, RAB setup, or RAB modification or when a
CELL_DCH UE experiences an incoming inter-RAT
handover or an incoming combined hard handover and
SRNS relocation. 2. Connected mode: After a UE
accesses a cell, the algorithm determines whether to
deliver periodic RSCP and Ec/N0 measurement control
messages. When the RNC receives periodic
measurement reports on the RSCP and Ec/N0, the
algorithm determines whether to initiate the SRB
reconfiguration process.
GUI Value Range:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SW
ITCH,
DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWIT
CH,
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH
, DRA_BASE_COVER_BE_E2D_SWITCH,
DRA_D2F_OVER_IUR_SWITCH,
DRA_CSPS_0K_RATE_UP_SWITCH,
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH,
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWIT
CH, DRA_BASE_COVER_E2D_DCCC_SWITCH,
DRA_WEB_FACH_DELAY_OPT_SWITCH,
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH,
DRA_D2P_WHEN_PS_INACT_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWIT
CH,
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH
Unit: None
Actual Value Range:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SW
ITCH,
DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWIT
CH,
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH
, DRA_BASE_COVER_BE_E2D_SWITCH,
DRA_D2F_OVER_IUR_SWITCH,
DRA_CSPS_0K_RATE_UP_SWITCH,
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH,
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWIT
CH, DRA_BASE_COVER_E2D_DCCC_SWITCH,
DRA_WEB_FACH_DELAY_OPT_SWITCH,
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH,
DRA_D2P_WHEN_PS_INACT_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWIT
CH,
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH
Default Value:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SW
ITCH:
0,DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWI
TCH:
0,DRA_BASE_COVER_BE_E2D_INITSEL_SWITC
H:0,DRA_BASE_COVER_BE_E2D_SWITCH:
0,DRA_D2F_OVER_IUR_SWITCH:
0,DRA_CSPS_0K_RATE_UP_SWITCH:
1,DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH:
0,DRA_PS_STATE_TRANS_WHEN_CS_REL_SWI
TCH:
0,DRA_BASE_COVER_E2D_DCCC_SWITCH:
0,DRA_WEB_FACH_DELAY_OPT_SWITCH:
0,DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH
:0,DRA_D2P_WHEN_PS_INACT_SWITCH:
0,DRA_INTELL_STATE_TRANS_ON_LOAD_SWI
TCH:
0,DRA_BASE_COVER_LOAD_SRB_H2D_SWITC
H:0
H, SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
R8_UE_SEL_DPUE_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEERROR_SWIT
CH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWIT
CH,
UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWIT
CH, CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SW
ITCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Default Value:
PS_F2D_OVERLAP_CELLUPT_SWITCH:
0,AMR_HHO_FAIL_ROLLBACK_SWITCH:
0,PHY_RECFG_REEST_SWITCH:
0,IUR_RL_REEST_SWITCH:
0,RB_SETUP_RL_REEST_SWITCH:
0,RRC_CONN_SETUP_OPT_SWITCH:
0,TCP_ACK_ACCELERATOR_SWITCH:
0,RRC_CELLFACH_TRB_RESET_TO_F2D_SWIT
CH:0,SEND_MSG_NULL_SWITCH:
0,FD_PCH_IUR_CS_OPT_SWITCH:
0,CELLUPT_T314_T315_TIMEOUT_OPT_SWITC
H:0,CS_HHO_ASYNC_CTRL_SWITCH:
0,PS_HHO_ASYNC_CTRL_SWITCH:
0,IUR_HHO_ASYNC_CTRL_SWITCH:
0,R8_UE_SEL_DPUE_SWITCH:
0,F2P_DATATRANS_OPTIMIZE_SWITCH:
0,IRATHO_HOCANCEL_RL_REEST_SWITCH:
0,TRB_RESET_RL_REEST_SWITCH:
TCP_ACK_ACCELERATOR_SWITCH,
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITC
H, SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEERROR_SWIT
CH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWIT
CH,
UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWIT
CH, CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SW
ITCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Unit: None
Actual Value Range:
PS_F2D_OVERLAP_CELLUPT_SWITCH,
AMR_HHO_FAIL_ROLLBACK_SWITCH,
PHY_RECFG_REEST_SWITCH,
IUR_RL_REEST_SWITCH,
RB_SETUP_RL_REEST_SWITCH,
RRC_CONN_SETUP_OPT_SWITCH,
TCP_ACK_ACCELERATOR_SWITCH,
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITC
H, SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEERROR_SWIT
CH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWIT
CH,
UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWIT
CH, CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SW
ITCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Default Value:
PS_F2D_OVERLAP_CELLUPT_SWITCH:
0,AMR_HHO_FAIL_ROLLBACK_SWITCH:
0,PHY_RECFG_REEST_SWITCH:
0,IUR_RL_REEST_SWITCH:
0,RB_SETUP_RL_REEST_SWITCH:
0,RRC_CONN_SETUP_OPT_SWITCH:
0,TCP_ACK_ACCELERATOR_SWITCH:
0,RRC_CELLFACH_TRB_RESET_TO_F2D_SWIT
CH:0,SEND_MSG_NULL_SWITCH:
0,FD_PCH_IUR_CS_OPT_SWITCH:
0,CELLUPT_T314_T315_TIMEOUT_OPT_SWITC
H:0,CS_HHO_ASYNC_CTRL_SWITCH:
0,PS_HHO_ASYNC_CTRL_SWITCH:
0,IUR_HHO_ASYNC_CTRL_SWITCH:
0,F2P_DATATRANS_OPTIMIZE_SWITCH:
0,IRATHO_HOCANCEL_RL_REEST_SWITCH:
0,TRB_RESET_RL_REEST_SWITCH:
0,RB_REL_RL_REEST_SWITCH:
0,RB_SETUP_ENHANCE_RL_REEST_SWITCH:
0,RAB_SETUPMOD_CNT_FIX_SWITCH:
0,PCH_UE_RLC_UNRECOVERABLEERROR_SWI
TCH:
0,FAST_RETURN_LTE_BY_CELL_SELECT_SWI
TCH:
0,UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH:
0,PHYCHRECFG_ENH_RL_REEST_SWITCH:
0,RBRECFG_ENH_RL_REEST_SWITCH:
UlBeTra BSC690 SET WRFD- Interacti Meaning: This parameter specifies the rate threshold for
ffThsOn 0 UFRCC 0106120 ve and decision to use E-DCH to carry UL PS domain
Hsupa HLTYP 6 Backgro background/interactive services. When the maximum
EPARA WRFD- und UL service rate is higher than or equal to this threshold,
150250 Traffic the service will be carried on E-DCH. Otherwise, it will
Class on be carried on DCH.
WRFD- HSUPA
010612 GUI Value Range: D8, D16, D32, D64, D128, D144,
3C- D256, D384, D608, D1280, D2048, D2720, D5440
WRFD- HSDPA
010701 Unit: kbit/s
HSUPA Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384,
Introduc 608, 1280, 2048, 2720, 5440
tion
Package Default Value: D608
Uplink
Enhance
d
CELL_F
ACH
UlBeTra BSC691 SET WRFD- Interacti Meaning: This parameter specifies the rate threshold for
ffThsOn 0 UFRCC 0106120 ve and decision to use E-DCH to carry UL PS domain
Hsupa HLTYP 6 Backgro background/interactive services. When the maximum
EPARA WRFD- und UL service rate is higher than or equal to this threshold,
150250 Traffic the service will be carried on E-DCH. Otherwise, it will
Class on be carried on DCH.
WRFD- HSUPA
010612 GUI Value Range: D8, D16, D32, D64, D128, D144,
3C- D256, D384, D608, D1280, D2048, D2720, D5440
WRFD- HSDPA
010701 Unit: kbit/s
HSUPA Actual Value Range: 8, 16, 32, 64, 128, 144, 256, 384,
Introduc 608, 1280, 2048, 2720, 5440
tion
Package Default Value: D608
Uplink
Enhance
d
CELL_F
ACH
MaxAll BSC690 ADD WRFD- Intra Meaning: The maximum allowed uplink transmit power
owedUl 0 UCELL 010801 RNC of a UE in the cell, which is related to the network
TxPowe SELRE WRFD- Cell planning. For details about this parameter, see 3GPP TS
r SEL 010802 Update 25.304.
MOD Inter GUI Value Range: -50~33
UCELL RNC Unit: dBm
SELRE Cell
SEL Update Actual Value Range: -50~33
Default Value: 24
MaxAll BSC691 ADD WRFD- Intra Meaning: The maximum allowed uplink transmit power
owedUl 0 UCELL 010801 RNC of a UE in the cell, which is related to the network
TxPowe SELRE WRFD- Cell planning. For details about this parameter, see 3GPP TS
r SEL 010802 Update 25.304.
MOD Inter GUI Value Range: -50~33
UCELL RNC Unit: dBm
SELRE Cell
SEL Update Actual Value Range: -50~33
Default Value: 24
BeThd6 BSC690 SET WRFD- TTI Meaning: Threshold for triggering event 6A1 for BE
A1 0 UEDCH 010690 Switch services. Event 6A1 is reported through a measurement
TTIREC for BE report, and is triggered when the transmit power of a UE
FG Services is greater than the absolute threshold for triggering event
Based 6A1. The value of this parameter is a relative threshold,
on which is calculated as follows: Absolute threshold for
Coverag triggering event 6A1 = Maximum uplink transmit
e power - Value of this parameter. This parameter is an
advanced parameter. To modify this parameter, contact
Huawei Customer Service Center for technical support.
GUI Value Range: 0~82
Unit: dB
Actual Value Range: 0~82
Default Value: 4
BeThd6 BSC691 SET WRFD- TTI Meaning: Threshold for triggering event 6A1 for BE
A1 0 UEDCH 010690 Switch services. Event 6A1 is reported through a measurement
TTIREC for BE report, and is triggered when the transmit power of a UE
FG Services is greater than the absolute threshold for triggering event
Based 6A1. The value of this parameter is a relative threshold,
on which is calculated as follows: Absolute threshold for
Coverag triggering event 6A1 = Maximum uplink transmit
e power - Value of this parameter. This parameter is an
advanced parameter. To modify this parameter, contact
Huawei Customer Service Center for technical support.
GUI Value Range: 0~82
Unit: dB
Actual Value Range: 0~82
Default Value: 4
BeThd6 BSC690 SET WRFD- TTI Meaning: Threshold for triggering event 6A2 for BE
A2 0 UEDCH 010690 Switch services. Event 6A2 is reported through a measurement
TTIREC for BE report, and is triggered when the transmit power of a UE
FG Services is greater than the absolute threshold for triggering event
Based 6A2. The value of this parameter is a relative threshold,
on which is calculated as follows: Absolute threshold for
Coverag triggering event 6A2 = Maximum uplink transmit
e power - Value of this parameter. This parameter is an
advanced parameter. To modify this parameter, contact
Huawei Customer Service Center for technical support.
GUI Value Range: 0~82
Unit: dB
Actual Value Range: 0~82
Default Value: 5
BeThd6 BSC691 SET WRFD- TTI Meaning: Threshold for triggering event 6A2 for BE
A2 0 UEDCH 010690 Switch services. Event 6A2 is reported through a measurement
TTIREC for BE report, and is triggered when the transmit power of a UE
FG Services is greater than the absolute threshold for triggering event
Based 6A2. The value of this parameter is a relative threshold,
on which is calculated as follows: Absolute threshold for
Coverag triggering event 6A2 = Maximum uplink transmit
e power - Value of this parameter. This parameter is an
advanced parameter. To modify this parameter, contact
Huawei Customer Service Center for technical support.
GUI Value Range: 0~82
Unit: dB
Actual Value Range: 0~82
Default Value: 5
BeThd6 BSC690 SET WRFD- TTI Meaning: Threshold for triggering event 6B1 for BE
B1 0 UEDCH 010690 Switch services. Event 6B1 is reported through a measurement
TTIREC for BE report, and is triggered when the transmit power of a UE
FG Services is smaller than the absolute threshold for triggering
Based event 6B1. The value of this parameter is a relative
on threshold, which is calculated as follows: Absolute
Coverag threshold for triggering event 6B1 = Maximum uplink
e transmit power - Value of this parameter. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: 0~82
Unit: dB
Actual Value Range: 0~82
Default Value: 4
BeThd6 BSC691 SET WRFD- TTI Meaning: Threshold for triggering event 6B1 for BE
B1 0 UEDCH 010690 Switch services. Event 6B1 is reported through a measurement
TTIREC for BE report, and is triggered when the transmit power of a UE
FG Services is smaller than the absolute threshold for triggering
Based event 6B1. The value of this parameter is a relative
on threshold, which is calculated as follows: Absolute
Coverag threshold for triggering event 6B1 = Maximum uplink
e transmit power - Value of this parameter. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: 0~82
Unit: dB
Actual Value Range: 0~82
Default Value: 4
BeThd6 BSC690 SET WRFD- TTI Meaning: Threshold for triggering event 6B2 for BE
B2 0 UEDCH 010690 Switch services. Event 6B2 is reported through a measurement
TTIREC for BE report, and is triggered when the transmit power of a UE
FG Services is smaller than the absolute threshold for triggering
Based event 6B2. The value of this parameter is a relative
on threshold, which is calculated as follows: Absolute
Coverag threshold for triggering event 6B2 = Maximum uplink
e transmit power - Value of this parameter. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: 0~82
Unit: dB
Actual Value Range: 0~82
Default Value: 5
BeThd6 BSC691 SET WRFD- TTI Meaning: Threshold for triggering event 6B2 for BE
B2 0 UEDCH 010690 Switch services. Event 6B2 is reported through a measurement
TTIREC for BE report, and is triggered when the transmit power of a UE
FG Services is smaller than the absolute threshold for triggering
Based event 6B2. The value of this parameter is a relative
on threshold, which is calculated as follows: Absolute
Coverag threshold for triggering event 6B2 = Maximum uplink
e transmit power - Value of this parameter. This
parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: 0~82
Unit: dB
Actual Value Range: 0~82
Default Value: 5
E2DThr BSC690 SET WRFD- UE State Meaning: Throughput event 4B threshold for BE
ou4BTh 0 UDCCC 010202 in service E-DCH-to-DCH channel switch in the uplink
d WRFD- Connect based on coverage
0106111 ed Mode GUI Value Range: 0~1148
1 (CELL-
DCH, Unit: 10kbit/s
CELL- Actual Value Range: 0~11480
PCH, Default Value: 2
URA-
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
E2DThr BSC691 SET WRFD- UE State Meaning: Throughput event 4B threshold for BE
ou4BTh 0 UDCCC 010202 in service E-DCH-to-DCH channel switch in the uplink
d WRFD- Connect based on coverage
0106111 ed Mode GUI Value Range: 0~1148
1 (CELL-
DCH, Unit: 10kbit/s
CELL- Actual Value Range: 0~11480
PCH, Default Value: 2
URA-
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
RabRsc BSC690 SET WRFD- TTI Meaning: Interval for UEs to report the RSCP after a
pPeriod 0 UCHLQ 010690 Switch service setup.
Timer UALIT for BE GUI Value Range: D250, D500, D1000, D2000, D3000,
YEVAL Services D4000, D6000, D8000, D12000, D16000, D20000,
UATE Based D24000, D28000, D32000, D64000
on
Coverag Unit: ms
e Actual Value Range: 250, 500, 1000, 2000, 3000, 4000,
6000, 8000, 12000, 16000, 20000, 24000, 28000,
32000, 64000
Default Value: D2000
RabRsc BSC691 SET WRFD- TTI Meaning: Interval for UEs to report the RSCP after a
pPeriod 0 UCHLQ 010690 Switch service setup.
Timer UALIT for BE GUI Value Range: D250, D500, D1000, D2000, D3000,
YEVAL Services D4000, D6000, D8000, D12000, D16000, D20000,
UATE Based D24000, D28000, D32000, D64000
on
Coverag Unit: ms
e Actual Value Range: 250, 500, 1000, 2000, 3000, 4000,
6000, 8000, 12000, 16000, 20000, 24000, 28000,
32000, 64000
Default Value: D2000
BeTTI2 BSC690 SET WRFD- TTI Meaning: Lower RSCP threshold for the RNC to
msRscp 0 UCHLQ 010690 Switch determine whether to allocate an E-DCH with 2 ms TTI
Thd UALIT for BE to BE services during a service setup and whether to
YEVAL Services perform 2-to-10 ms TTI switching on BE services after
UATE Based a service setup. When the revised RSCP of the best cell
on exceeds this threshold, the RNC allocates an E-DCH
Coverag with 2 ms TTI to BE services that meet the requirements
e of 2 ms TTI during a service setup. When the RSCP of
the cell does not exceed this threshold, the RNC
allocates an E-DCH with 10 ms TTI or an uplink DCH
to these BE services. The RNC performs 2-to-10 ms TTI
switching on a BE service when the requirements for
the allocation of 10 ms TTI are met and the RSCP of the
cell does not exceed this threshold. The revised RSCP
of the best cell can be calculated using the following
formula: Revised RSCP = Reported RSCP - (CPICH
transmit power - 33dBm) - (RTWP + 105.2dBm)
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -95
BeTTI2 BSC691 SET WRFD- TTI Meaning: Lower RSCP threshold for the RNC to
msRscp 0 UCHLQ 010690 Switch determine whether to allocate an E-DCH with 2 ms TTI
Thd UALIT for BE to BE services during a service setup and whether to
YEVAL Services perform 2-to-10 ms TTI switching on BE services after
UATE Based a service setup. When the revised RSCP of the best cell
on exceeds this threshold, the RNC allocates an E-DCH
Coverag with 2 ms TTI to BE services that meet the requirements
e of 2 ms TTI during a service setup. When the RSCP of
the cell does not exceed this threshold, the RNC
allocates an E-DCH with 10 ms TTI or an uplink DCH
to these BE services. The RNC performs 2-to-10 ms TTI
switching on a BE service when the requirements for
the allocation of 10 ms TTI are met and the RSCP of the
cell does not exceed this threshold. The revised RSCP
of the best cell can be calculated using the following
formula: Revised RSCP = Reported RSCP - (CPICH
transmit power - 33dBm) - (RTWP + 105.2dBm)
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -95
BeTTI1 BSC690 SET WRFD- TTI Meaning: Lower RSCP threshold for the RNC to
0msRsc 0 UCHLQ 010690 Switch determine whether to allocate an E-DCH with 10 ms
pThd UALIT for BE TTI to BE services during a service setup and whether
YEVAL Services to switch BE services from 10 ms TTI to the DCH after
UATE Based a service setup. When the revised RSCP of the best cell
on exceeds this threshold, the RNC allocates an E-DCH
Coverag with 10 ms TTI to BE services that meet the
e requirements of 10 ms TTI during a service setup. When
the RSCP of the cell does not exceed this threshold, the
RNC allocates an uplink DCH to these BE services. The
RNC switches a BE service from 10 ms TTI to the DCH
when the requirements for the allocation of a DCH are
met and the RSCP of the cell does not exceed this
threshold. The revised RSCP of the best cell can be
calculated using the following formula: Revised RSCP
= Reported RSCP - (CPICH transmit power - 33dBm)
- (RTWP + 105.2dBm)
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -105
BeTTI1 BSC691 SET WRFD- TTI Meaning: Lower RSCP threshold for the RNC to
0msRsc 0 UCHLQ 010690 Switch determine whether to allocate an E-DCH with 10 ms
pThd UALIT for BE TTI to BE services during a service setup and whether
YEVAL Services to switch BE services from 10 ms TTI to the DCH after
UATE Based a service setup. When the revised RSCP of the best cell
on exceeds this threshold, the RNC allocates an E-DCH
Coverag with 10 ms TTI to BE services that meet the
e requirements of 10 ms TTI during a service setup. When
the RSCP of the cell does not exceed this threshold, the
RNC allocates an uplink DCH to these BE services. The
RNC switches a BE service from 10 ms TTI to the DCH
when the requirements for the allocation of a DCH are
met and the RSCP of the cell does not exceed this
threshold. The revised RSCP of the best cell can be
calculated using the following formula: Revised RSCP
= Reported RSCP - (CPICH transmit power - 33dBm)
- (RTWP + 105.2dBm)
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -105
EcN0Eff BSC691 SET WRFD- 3.4/6.8/1 Meaning: Time period for valid Ec/No or RSCP. This
ectTime 0 UFRC 010510 3.6/27.2 parameter defines the time period during which the
WRFD- Kbps reported values of Ec/No or RSCP are considered as
010690 RRC valid values. The time period starts from the time the
Connect system receives the first Ec/No or RSCP.
WRFD- ion and
010507 GUI Value Range: 0~65535
Radio
WRFD- Access Unit: ms
150232 Bearer Actual Value Range: 0~65535
WRFD- Establis Default Value: 5000
010612 hment
and
WRFD-
Release
020400
TTI
Switch
for BE
Services
Based
on
Coverag
e
Rate
Negotiat
ion at
Admissi
on
Control
Multiba
nd
Direct
Retry
Based
on UE
Location
HSUPA
Introduc
tion
Package
DRD
Introduc
tion
Package
EcN0Eff BSC690 SET WRFD- 3.4/6.8/1 Meaning: Time period for valid Ec/No or RSCP. This
ectTime 0 UFRC 010510 3.6/27.2 parameter defines the time period during which the
WRFD- Kbps reported values of Ec/No or RSCP are considered as
010690 RRC valid values. The time period starts from the time the
Connect system receives the first Ec/No or RSCP.
WRFD- ion and
010507 GUI Value Range: 0~65535
Radio
WRFD- Access Unit: ms
150232 Bearer Actual Value Range: 0~65535
WRFD- Establis Default Value: 5000
010612 hment
and
WRFD-
Release
020400
TTI
Switch
for BE
Services
Based
on
Coverag
e
Rate
Negotiat
ion at
Admissi
on
Control
Multiba
nd
Direct
Retry
Based
on UE
Location
HSUPA
Introduc
tion
Package
DRD
Introduc
tion
Package
BaseCo BSC690 SET WRFD- Dynami Meaning: Relative threshold of event 6B when
verD2E 0 UDCCC 021101 c coverage-based uplink BE services are switched over
6BThd WRFD- Channel from DCHs to E-DCHs.This parameter specifies the
020309 Configu relative threshold of event 6B. If the UE transmit power
ration is lower than the absolute threshold of event 6B, event
WRFD- Control 6B will be triggered. Absolute threshold of event 6B =
0106111 (DCCC) Maximum uplink transmit power - Relative threshold
1 of event 6B. Event 6B must be triggered before uplink
Inter-
WRFD- RAT services are switched over from DCHs to E-DCHs. For
020304 Handov details about this parameter, see 3GPP TS 25.331.
WRFD- er Based GUI Value Range: 0~82
010202 on DL Unit: None
QoS
Actual Value Range: 0~82
HSDPA
State Default Value: 10
Transiti
on
Inter
Frequen
cy Hard
Handov
er Based
on DL
QoS
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BaseCo BSC691 SET WRFD- Dynami Meaning: Relative threshold of event 6B when
verD2E 0 UDCCC 021101 c coverage-based uplink BE services are switched over
6BThd WRFD- Channel from DCHs to E-DCHs.This parameter specifies the
020309 Configu relative threshold of event 6B. If the UE transmit power
ration is lower than the absolute threshold of event 6B, event
WRFD- Control 6B will be triggered. Absolute threshold of event 6B =
0106111 (DCCC) Maximum uplink transmit power - Relative threshold
1 of event 6B. Event 6B must be triggered before uplink
Inter-
WRFD- RAT services are switched over from DCHs to E-DCHs. For
020304 Handov details about this parameter, see 3GPP TS 25.331.
WRFD- er Based GUI Value Range: 0~82
010202 on DL Unit: None
QoS
Actual Value Range: 0~82
HSDPA
State Default Value: 10
Transiti
on
Inter
Frequen
cy Hard
Handov
er Based
on DL
QoS
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BaseCo BSC690 SET WRFD- Dynami Meaning: Relative threshold of event 6A when
verD2E 0 UDCCC 021101 c coverage-based uplink BE services are switched over
6AThd WRFD- Channel from DCHs to E-DCHs. If the UE transmit power is
020309 Configu higher than the absolute threshold of event 6A, event
ration 6A is triggered. Absolute threshold of event 6A =
WRFD- Control Maximum uplink transmit power - Relative threshold
0106111 (DCCC) of event 6A. For details about this parameter, see 3GPP
1 TS 25.331.
Inter-
WRFD- RAT GUI Value Range: 0~82
020304 Handov Unit: None
WRFD- er Based
010202 on DL Actual Value Range: 0~82
QoS Default Value: 9
HSDPA
State
Transiti
on
Inter
Frequen
cy Hard
Handov
er Based
on DL
QoS
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BaseCo BSC691 SET WRFD- Dynami Meaning: Relative threshold of event 6A when
verD2E 0 UDCCC 021101 c coverage-based uplink BE services are switched over
6AThd WRFD- Channel from DCHs to E-DCHs. If the UE transmit power is
020309 Configu higher than the absolute threshold of event 6A, event
ration 6A is triggered. Absolute threshold of event 6A =
WRFD- Control Maximum uplink transmit power - Relative threshold
0106111 (DCCC) of event 6A. For details about this parameter, see 3GPP
1 TS 25.331.
Inter-
WRFD- RAT GUI Value Range: 0~82
020304 Handov Unit: None
WRFD- er Based
010202 on DL Actual Value Range: 0~82
QoS Default Value: 9
HSDPA
State
Transiti
on
Inter
Frequen
cy Hard
Handov
er Based
on DL
QoS
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
Event4a BSC690 ADD WRFD- Dynami Meaning: Traffic upper limit for the DCH to trigger
Thd 0 UTYPR 021101 c event 4A.
ABDCC Channel GUI Value Range: D16, D32, D64, D128, D256, D512,
CMC Configu D1024, D2K, D3K, D4K, D6K, D8K, D12K, D16K,
MOD ration D24K, D32K, D48K, D64K, D96K, D128K, D192K,
UTYPR Control D256K, D384K, D512K, D768K
ABDCC (DCCC)
Unit: byte
CMC
Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
2K, 3K, 4K, 6K, 8K, 12K, 16K, 24K, 32K, 48K, 64K,
96K, 128K, 192K, 256K, 384K, 512K, 768K
Default Value: D1024
Event4a BSC691 ADD WRFD- Dynami Meaning: Traffic upper limit for the DCH to trigger
Thd 0 UTYPR 021101 c event 4A.
ABDCC Channel GUI Value Range: D16, D32, D64, D128, D256, D512,
CMC Configu D1024, D2K, D3K, D4K, D6K, D8K, D12K, D16K,
MOD ration D24K, D32K, D48K, D64K, D96K, D128K, D192K,
UTYPR Control D256K, D384K, D512K, D768K
ABDCC (DCCC)
Unit: byte
CMC
Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
2K, 3K, 4K, 6K, 8K, 12K, 16K, 24K, 32K, 48K, 64K,
96K, 128K, 192K, 256K, 384K, 512K, 768K
Default Value: D1024
BeCpc2 BSC690 SET WRFD- CPC - Meaning: Timer for state transition from CPC to FACH
FStateTr 0 UUEST 010686 DTX / of BE services, used to check whether the UE in the
ansTime ATETR WRFD- DRX CELL_DCH(with CPC) state with BE services is in the
r ANSTI 010687 CPC - stable low activity state.
MER HS- GUI Value Range: 1~65535
WRFD-
0106111 SCCH Unit: s
1 less
operatio Actual Value Range: 1~65535
WRFD- n Default Value: 5
010202
HSDPA
State
Transiti
on
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeCpc2 BSC691 SET WRFD- CPC - Meaning: Timer for state transition from CPC to FACH
FStateTr 0 UUEST 010686 DTX / of BE services, used to check whether the UE in the
ansTime ATETR WRFD- DRX CELL_DCH(with CPC) state with BE services is in the
r ANSTI 010687 CPC - stable low activity state.
MER HS- GUI Value Range: 1~65535
WRFD-
0106111 SCCH Unit: s
1 less
operatio Actual Value Range: 1~65535
WRFD- n Default Value: 5
010202
HSDPA
State
Transiti
on
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtCpc2 BSC690 SET WRFD- CPC - Meaning: Timer for state transition from CPC to FACH
FStateTr 0 UUEST 010686 DTX / of real-time services, used to check whether the UE in
ansTime ATETR WRFD- DRX the CELL_DCH(with CPC) state with real-time
r ANSTI 010687 CPC - services is in the stable low activity state.
MER HS- GUI Value Range: 1~65535
WRFD-
0106111 SCCH Unit: s
1 less
operatio Actual Value Range: 1~65535
WRFD- n Default Value: 180
010202
HSDPA
State
Transiti
on
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtCpc2 BSC691 SET WRFD- CPC - Meaning: Timer for state transition from CPC to FACH
FStateTr 0 UUEST 010686 DTX / of real-time services, used to check whether the UE in
ansTime ATETR WRFD- DRX the CELL_DCH(with CPC) state with real-time
r ANSTI 010687 CPC - services is in the stable low activity state.
MER HS- GUI Value Range: 1~65535
WRFD-
0106111 SCCH Unit: s
1 less
operatio Actual Value Range: 1~65535
WRFD- n Default Value: 180
010202
HSDPA
State
Transiti
on
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeD2EF BSC690 SET WRFD- UE State Meaning: Timer for state transition from DCH to
achState 0 UUEST 010202 in E_FACH of BE services, used to check whether the UE
TransTi ATETR WRFD- Connect in the CELL_DCH(with DCH) state with BE services
mer ANSTI 0106111 ed Mode is in the stable low activity state.
MER 1 (CELL- GUI Value Range: 1~65535
DCH,
WRFD- CELL- Unit: s
010688 PCH, Actual Value Range: 1~65535
URA- Default Value: 5
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeD2EF BSC691 SET WRFD- UE State Meaning: Timer for state transition from DCH to
achState 0 UUEST 010202 in E_FACH of BE services, used to check whether the UE
TransTi ATETR WRFD- Connect in the CELL_DCH(with DCH) state with BE services
mer ANSTI 0106111 ed Mode is in the stable low activity state.
MER 1 (CELL- GUI Value Range: 1~65535
DCH,
WRFD- CELL- Unit: s
010688 PCH, Actual Value Range: 1~65535
URA- Default Value: 5
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeH2EF BSC690 SET WRFD- UE State Meaning: Timer for state transition from HSPA to
achState 0 UUEST 010202 in E_FACH of BE services, used to check whether the UE
TransTi ATETR WRFD- Connect in the CELL_DCH(with HSPA) state with BE services
mer ANSTI 0106111 ed Mode is in the stable low activity state.
MER 1 (CELL- GUI Value Range: 1~65535
DCH,
WRFD- CELL- Unit: s
010688 PCH, Actual Value Range: 1~65535
URA- Default Value: 5
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeH2EF BSC691 SET WRFD- UE State Meaning: Timer for state transition from HSPA to
achState 0 UUEST 010202 in E_FACH of BE services, used to check whether the UE
TransTi ATETR WRFD- Connect in the CELL_DCH(with HSPA) state with BE services
mer ANSTI 0106111 ed Mode is in the stable low activity state.
MER 1 (CELL- GUI Value Range: 1~65535
DCH,
WRFD- CELL- Unit: s
010688 PCH, Actual Value Range: 1~65535
URA- Default Value: 5
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
RtDH2E BSC690 SET WRFD- UE State Meaning: Timer for state transition from DCH or HSPA
FachStat 0 UUEST 010202 in to E_FACH of real-time services, used to check whether
eTransT ATETR WRFD- Connect the UE in the CELL_DCH state with real-time services
imer ANSTI 0106111 ed Mode is in the stable low activity state.
MER 1 (CELL- GUI Value Range: 1~65535
DCH,
WRFD- CELL- Unit: s
010688 PCH, Actual Value Range: 1~65535
URA- Default Value: 180
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
RtDH2E BSC691 SET WRFD- UE State Meaning: Timer for state transition from DCH or HSPA
FachStat 0 UUEST 010202 in to E_FACH of real-time services, used to check whether
eTransT ATETR WRFD- Connect the UE in the CELL_DCH state with real-time services
imer ANSTI 0106111 ed Mode is in the stable low activity state.
MER 1 (CELL- GUI Value Range: 1~65535
DCH,
WRFD- CELL- Unit: s
010688 PCH, Actual Value Range: 1~65535
URA- Default Value: 180
PCH,
CELL-
FACH)
HSDPA
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeCpc2 BSC690 SET WRFD- CPC - Meaning: Timer for state transition from CPC to
EFachSt 0 UUEST 010686 DTX / E_FACH of BE services, used to check whether the UE
ateTrans ATETR WRFD- DRX in the CELL_DCH(with CPC) state with BE services is
Timer ANSTI 010687 CPC - in the stable low activity state.
MER HS- GUI Value Range: 1~65535
WRFD-
0106111 SCCH Unit: s
1 less
operatio Actual Value Range: 1~65535
WRFD- n Default Value: 5
010688
HSDPA
WRFD- State
010202 Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeCpc2 BSC691 SET WRFD- CPC - Meaning: Timer for state transition from CPC to
EFachSt 0 UUEST 010686 DTX / E_FACH of BE services, used to check whether the UE
ateTrans ATETR WRFD- DRX in the CELL_DCH(with CPC) state with BE services is
Timer ANSTI 010687 CPC - in the stable low activity state.
MER HS- GUI Value Range: 1~65535
WRFD-
0106111 SCCH Unit: s
1 less
operatio Actual Value Range: 1~65535
WRFD- n Default Value: 5
010688
HSDPA
WRFD- State
010202 Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtCpc2 BSC690 SET WRFD- CPC - Meaning: Timer for state transition from CPC to
EFachSt 0 UUEST 010686 DTX / E_FACH of real-time services, used to check whether
ateTrans ATETR WRFD- DRX the UE in the CELL_DCH(with CPC) state with real-
Timer ANSTI 010687 CPC - time services is in the stable low activity state.
MER HS- GUI Value Range: 1~65535
WRFD-
0106111 SCCH Unit: s
1 less
operatio Actual Value Range: 1~65535
WRFD- n Default Value: 180
010688
HSDPA
WRFD- State
010202 Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtCpc2 BSC691 SET WRFD- CPC - Meaning: Timer for state transition from CPC to
EFachSt 0 UUEST 010686 DTX / E_FACH of real-time services, used to check whether
ateTrans ATETR WRFD- DRX the UE in the CELL_DCH(with CPC) state with real-
Timer ANSTI 010687 CPC - time services is in the stable low activity state.
MER HS- GUI Value Range: 1~65535
WRFD-
0106111 SCCH Unit: s
1 less
operatio Actual Value Range: 1~65535
WRFD- n Default Value: 180
010688
HSDPA
WRFD- State
010202 Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeF2Cp BSC690 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
cHTvm 0 UUEST 010686 DTX / of 4A event for triggering the transition of BE services
TimeTo ATETR WRFD- DRX from FACH to HS-DSCH with CPC technology. This
Trig ANS 010687 CPC - parameter can prevent unnecessary reports to be
HS- triggered, caused by traffic volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010202 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
State 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeF2Cp BSC691 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
cHTvm 0 UUEST 010686 DTX / of 4A event for triggering the transition of BE services
TimeTo ATETR WRFD- DRX from FACH to HS-DSCH with CPC technology. This
Trig ANS 010687 CPC - parameter can prevent unnecessary reports to be
HS- triggered, caused by traffic volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010202 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
State 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtF2Cp BSC690 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
cTvmTi 0 UUEST 010686 DTX / of 4A event for triggering the transition of real-time
meToTri ATETR WRFD- DRX services from FACH to HSPA with CPC technology.
g ANS 010687 CPC - This parameter can prevent unnecessary reports to be
HS- triggered, caused by traffic volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010202 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
State 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtF2Cp BSC691 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
cTvmTi 0 UUEST 010686 DTX / of 4A event for triggering the transition of real-time
meToTri ATETR WRFD- DRX services from FACH to HSPA with CPC technology.
g ANS 010687 CPC - This parameter can prevent unnecessary reports to be
HS- triggered, caused by traffic volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010202 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
State 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeF2Cp BSC690 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
cETvmT 0 UUEST 010686 DTX / of 4A event for triggering the transition of BE services
imeToTr ATETR WRFD- DRX from FACH to E-DCH with CPC technology. This
ig ANS 010687 CPC - parameter can prevent unnecessary reports to be
HS- triggered, caused by traffic volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010202 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
State 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeF2Cp BSC691 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
cETvmT 0 UUEST 010686 DTX / of 4A event for triggering the transition of BE services
imeToTr ATETR WRFD- DRX from FACH to E-DCH with CPC technology. This
ig ANS 010687 CPC - parameter can prevent unnecessary reports to be
HS- triggered, caused by traffic volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010202 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
State 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeF2Cp BSC690 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
cHTvm 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
Thd ATETR WRFD- DRX of BE services from FACH to HS-DSCH with CPC
ANS 010687 CPC - technology.
WRFD- HS- GUI Value Range: D16, D32, D64, D128, D256, D512,
0106111 SCCH D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
1 less D32k, D48k, D64k, D96k, D128k, D192k, D256k,
operatio D384k, D512k, D768k
WRFD- n
010202 Unit: byte
HSDPA Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
State 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
Transiti 128k, 192k, 256k, 384k, 512k, 768k
on
Default Value: D512
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeF2Cp BSC691 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
cHTvm 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
Thd ATETR WRFD- DRX of BE services from FACH to HS-DSCH with CPC
ANS 010687 CPC - technology.
WRFD- HS- GUI Value Range: D16, D32, D64, D128, D256, D512,
0106111 SCCH D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
1 less D32k, D48k, D64k, D96k, D128k, D192k, D256k,
operatio D384k, D512k, D768k
WRFD- n
010202 Unit: byte
HSDPA Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
State 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
Transiti 128k, 192k, 256k, 384k, 512k, 768k
on
Default Value: D512
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtF2Cp BSC690 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
cTvmTh 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
d ATETR WRFD- DRX of real-time services from FACH to HSPA with CPC
ANS 010687 CPC - technology.
WRFD- HS- GUI Value Range: D16, D32, D64, D128, D256, D512,
0106111 SCCH D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
1 less D32k, D48k, D64k, D96k, D128k, D192k, D256k,
operatio D384k, D512k, D768k
WRFD- n
010202 Unit: byte
HSDPA Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
State 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
Transiti 128k, 192k, 256k, 384k, 512k, 768k
on
Default Value: D512
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtF2Cp BSC691 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
cTvmTh 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
d ATETR WRFD- DRX of real-time services from FACH to HSPA with CPC
ANS 010687 CPC - technology.
WRFD- HS- GUI Value Range: D16, D32, D64, D128, D256, D512,
0106111 SCCH D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
1 less D32k, D48k, D64k, D96k, D128k, D192k, D256k,
operatio D384k, D512k, D768k
WRFD- n
010202 Unit: byte
HSDPA Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
State 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
Transiti 128k, 192k, 256k, 384k, 512k, 768k
on
Default Value: D512
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeF2Cp BSC690 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
cETvmT 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
hd ATETR WRFD- DRX of BE services from FACH to E-DCH with CPC
ANS 010687 CPC - technology.
WRFD- HS- GUI Value Range: D16, D32, D64, D128, D256, D512,
0106111 SCCH D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
1 less D32k, D48k, D64k, D96k, D128k, D192k, D256k,
operatio D384k, D512k, D768k
WRFD- n
010202 Unit: byte
HSDPA Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
State 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
Transiti 128k, 192k, 256k, 384k, 512k, 768k
on
Default Value: D512
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeF2Cp BSC691 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
cETvmT 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
hd ATETR WRFD- DRX of BE services from FACH to E-DCH with CPC
ANS 010687 CPC - technology.
WRFD- HS- GUI Value Range: D16, D32, D64, D128, D256, D512,
0106111 SCCH D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
1 less D32k, D48k, D64k, D96k, D128k, D192k, D256k,
operatio D384k, D512k, D768k
WRFD- n
010202 Unit: byte
HSDPA Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
State 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
Transiti 128k, 192k, 256k, 384k, 512k, 768k
on
Default Value: D512
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeEFac BSC690 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
h2DTv 0 UUEST 010202 in of 4A event for triggering the transition of BE services
mTimeT ATETR WRFD- Connect from E_FACH to DCH. This parameter can prevent
oTrig ANS 0106111 ed Mode unnecessary reports to be triggered, caused by traffic
1 (CELL- volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
WRFD- CELL-
010688 D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
HSDPA Default Value: D0
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeEFac BSC691 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
h2DTv 0 UUEST 010202 in of 4A event for triggering the transition of BE services
mTimeT ATETR WRFD- Connect from E_FACH to DCH. This parameter can prevent
oTrig ANS 0106111 ed Mode unnecessary reports to be triggered, caused by traffic
1 (CELL- volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
WRFD- CELL-
010688 D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
HSDPA Default Value: D0
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeEFac BSC690 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
h2HTv 0 UUEST 010202 in of 4A event for triggering the transition of BE services
mTimeT ATETR WRFD- Connect from E_FACH to HS-DSCH. This parameter can
oTrig ANS 0106111 ed Mode prevent unnecessary reports to be triggered, caused by
1 (CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
WRFD- CELL-
010688 D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
HSDPA Default Value: D0
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeEFac BSC691 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
h2HTv 0 UUEST 010202 in of 4A event for triggering the transition of BE services
mTimeT ATETR WRFD- Connect from E_FACH to HS-DSCH. This parameter can
oTrig ANS 0106111 ed Mode prevent unnecessary reports to be triggered, caused by
1 (CELL- traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
WRFD- CELL-
010688 D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
HSDPA Default Value: D0
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
RtEFach BSC690 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
2DHTv 0 UUEST 010202 in of 4A event for triggering the transition of real-time
mTimeT ATETR WRFD- Connect services from E_FACH to DCH or HSPA. This
oTrig ANS 0106111 ed Mode parameter can prevent unnecessary reports to be
1 (CELL- triggered, caused by traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
WRFD- CELL-
010688 D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
HSDPA Default Value: D0
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
RtEFach BSC691 SET WRFD- UE State Meaning: This parameter specifies the occurrence time
2DHTv 0 UUEST 010202 in of 4A event for triggering the transition of real-time
mTimeT ATETR WRFD- Connect services from E_FACH to DCH or HSPA. This
oTrig ANS 0106111 ed Mode parameter can prevent unnecessary reports to be
1 (CELL- triggered, caused by traffic volume variation.
DCH, GUI Value Range: D0, D10, D20, D40, D60, D80,
WRFD- CELL-
010688 D100, D120, D160, D200, D240, D320, D640, D1280,
PCH, D2560, D5000
URA-
PCH, Unit: ms
CELL- Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
FACH) 200, 240, 320, 640, 1280, 2560, 5000
HSDPA Default Value: D0
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeEFac BSC690 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
h2DTv 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
mThd ATETR WRFD- Connect of BE services from E_FACH to DCH.
ANS 0106111 ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
1 (CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
WRFD- CELL-
010688 D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
HSDPA Default Value: D512
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeEFac BSC691 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
h2DTv 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
mThd ATETR WRFD- Connect of BE services from E_FACH to DCH.
ANS 0106111 ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
1 (CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
WRFD- CELL-
010688 D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
HSDPA Default Value: D512
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeEFac BSC690 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
h2HTv 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
mThd ATETR WRFD- Connect of BE services from E_FACH to HS-DSCH.
ANS 0106111 ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
1 (CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
WRFD- CELL-
010688 D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
HSDPA Default Value: D512
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeEFac BSC691 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
h2HTv 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
mThd ATETR WRFD- Connect of BE services from E_FACH to HS-DSCH.
ANS 0106111 ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
1 (CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
WRFD- CELL-
010688 D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
HSDPA Default Value: D512
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
RtEFach BSC690 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
2DHTv 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
mThd ATETR WRFD- Connect of real-time services from E_FACH to DCH or HSPA.
ANS 0106111 ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
1 (CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
WRFD- CELL-
010688 D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
HSDPA Default Value: D512
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
RtEFach BSC691 SET WRFD- UE State Meaning: This parameter specifies the threshold of the
2DHTv 0 UUEST 010202 in traffic volume of 4A event for triggering the transition
mThd ATETR WRFD- Connect of real-time services from E_FACH to DCH or HSPA.
ANS 0106111 ed Mode GUI Value Range: D16, D32, D64, D128, D256, D512,
1 (CELL- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
DCH, D32k, D48k, D64k, D96k, D128k, D192k, D256k,
WRFD- CELL-
010688 D384k, D512k, D768k
PCH,
URA- Unit: byte
PCH, Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
CELL- 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
FACH) 128k, 192k, 256k, 384k, 512k, 768k
HSDPA Default Value: D512
State
Transiti
on
Downlin
k
Enhance
d
CELL_F
ACH
BeEFac BSC690 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
h2CpcT 0 UUEST 010686 DTX / of 4A event for triggering the transition of BE services
vmTime ATETR WRFD- DRX from E_FACH to CPC. This parameter can prevent
ToTrig ANS 010687 CPC - unnecessary reports to be triggered, caused by traffic
HS- volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010688 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
WRFD- State
010202 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeEFac BSC691 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
h2CpcT 0 UUEST 010686 DTX / of 4A event for triggering the transition of BE services
vmTime ATETR WRFD- DRX from E_FACH to CPC. This parameter can prevent
ToTrig ANS 010687 CPC - unnecessary reports to be triggered, caused by traffic
HS- volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010688 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
WRFD- State
010202 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtEFach BSC690 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
2CpcTv 0 UUEST 010686 DTX / of 4A event for triggering the transition of real-time
mTimeT ATETR WRFD- DRX services from E_FACH to HSPA with CPC technology.
oTrig ANS 010687 CPC - This parameter can prevent unnecessary reports to be
HS- triggered, caused by traffic volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010688 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
WRFD- State
010202 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtEFach BSC691 SET WRFD- CPC - Meaning: This parameter specifies the occurrence time
2CpcTv 0 UUEST 010686 DTX / of 4A event for triggering the transition of real-time
mTimeT ATETR WRFD- DRX services from E_FACH to HSPA with CPC technology.
oTrig ANS 010687 CPC - This parameter can prevent unnecessary reports to be
HS- triggered, caused by traffic volume variation.
WRFD-
0106111 SCCH GUI Value Range: D0, D10, D20, D40, D60, D80,
1 less D100, D120, D160, D200, D240, D320, D640, D1280,
operatio D2560, D5000
WRFD- n
010688 Unit: ms
HSDPA Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160,
WRFD- State
010202 200, 240, 320, 640, 1280, 2560, 5000
Transiti
on Default Value: D0
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeEFac BSC690 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
h2CpcT 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
vmThd ATETR WRFD- DRX of BE services from E_FACH to CPC.
ANS 010687 CPC - GUI Value Range: D16, D32, D64, D128, D256, D512,
WRFD- HS- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
0106111 SCCH D32k, D48k, D64k, D96k, D128k, D192k, D256k,
1 less D384k, D512k, D768k
operatio Unit: byte
WRFD- n
010688 Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
HSDPA 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
WRFD- State
010202 128k, 192k, 256k, 384k, 512k, 768k
Transiti
on Default Value: D512
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
BeEFac BSC691 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
h2CpcT 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
vmThd ATETR WRFD- DRX of BE services from E_FACH to CPC.
ANS 010687 CPC - GUI Value Range: D16, D32, D64, D128, D256, D512,
WRFD- HS- D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
0106111 SCCH D32k, D48k, D64k, D96k, D128k, D192k, D256k,
1 less D384k, D512k, D768k
operatio Unit: byte
WRFD- n
010688 Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
HSDPA 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
WRFD- State
010202 128k, 192k, 256k, 384k, 512k, 768k
Transiti
on Default Value: D512
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtEFach BSC690 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
2CpcTv 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
mThd ATETR WRFD- DRX of real-time services from E_FACH to HSPA with CPC
ANS 010687 CPC - technology.
WRFD- HS- GUI Value Range: D16, D32, D64, D128, D256, D512,
0106111 SCCH D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
1 less D32k, D48k, D64k, D96k, D128k, D192k, D256k,
operatio D384k, D512k, D768k
WRFD- n
010688 Unit: byte
HSDPA Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
WRFD- State
010202 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
Transiti 128k, 192k, 256k, 384k, 512k, 768k
on
Default Value: D512
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
RtEFach BSC691 SET WRFD- CPC - Meaning: This parameter specifies the threshold of the
2CpcTv 0 UUEST 010686 DTX / traffic volume of 4A event for triggering the transition
mThd ATETR WRFD- DRX of real-time services from E_FACH to HSPA with CPC
ANS 010687 CPC - technology.
WRFD- HS- GUI Value Range: D16, D32, D64, D128, D256, D512,
0106111 SCCH D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k,
1 less D32k, D48k, D64k, D96k, D128k, D192k, D256k,
operatio D384k, D512k, D768k
WRFD- n
010688 Unit: byte
HSDPA Actual Value Range: 16, 32, 64, 128, 256, 512, 1024,
WRFD- State
010202 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k,
Transiti 128k, 192k, 256k, 384k, 512k, 768k
on
Default Value: D512
Downlin
k
Enhance
d
CELL_F
ACH
UE State
in
Connect
ed Mode
(CELL-
DCH,
CELL-
PCH,
URA-
PCH,
CELL-
FACH)
TthdFor BSC690 SET WRFD- UE State Meaning: Timer for determining whether a UE is
SFSTUs 0 USTAT 010202 in capable of fast state transition. If the interval between
erIdentif ETIME Connect the time when a UE with best effort (BE) services leaves
y R ed Mode the CELL_DCH state and the time when the UE reenters
(CELL- the CELL_DCH state is greater than or equal to this
DCH, threshold, the RNC determines that the UE is capable
CELL- of fast state transition.
PCH, GUI Value Range: 0~3600
URA-
PCH, Unit: s
CELL- Actual Value Range: 0~3600
FACH) Default Value: 15
TthdFor BSC691 SET WRFD- UE State Meaning: Timer for determining whether a UE is
SFSTUs 0 USTAT 010202 in capable of fast state transition. If the interval between
erIdentif ETIME Connect the time when a UE with best effort (BE) services leaves
y R ed Mode the CELL_DCH state and the time when the UE reenters
(CELL- the CELL_DCH state is greater than or equal to this
DCH, threshold, the RNC determines that the UE is capable
CELL- of fast state transition.
PCH, GUI Value Range: 0~3600
URA-
PCH, Unit: s
CELL- Actual Value Range: 0~3600
FACH) Default Value: 15
PsInactT BSC690 SET WRFD- UE State Meaning: Timer for FD-enabled UEs or LTE-enabled
mrForFs 0 UPSIN 010202 in UEs staying in the CELL_DCH state. When UEs that
tDrmDc ACTTI WRFD- Connect are enabled with Fast Dormancy (FD) and stay in the
h MER 140226 ed Mode CELL_DCH state do not transmit any data after this
(CELL- timer expires, the RNC transits the UEs to the
WRFD- DCH, CELL_FACH or CELL_PCH state. When LTE-
020500 CELL- enabled UEs in the CELL_DCH state do not transmit
PCH, any data after this timer expires, the RNC transits the
URA- UEs to the CELL_PCH or IDLE state. You can set this
PCH, timer to a value other than 0 if you want to check
CELL- whether FD-enabled UEs and LTE-enabled UEs are in
FACH) the CELL_DCH state.
Fast GUI Value Range: 0~64800
Return Unit: s
from
UMTS Actual Value Range: 0~64800
to LTE Default Value: 4
Enhance
d Fast
Dorman
cy
PsInactT BSC691 SET WRFD- UE State Meaning: Timer for FD-enabled UEs or LTE-enabled
mrForFs 0 UPSIN 010202 in UEs staying in the CELL_DCH state. When UEs that
tDrmDc ACTTI WRFD- Connect are enabled with Fast Dormancy (FD) and stay in the
h MER 140226 ed Mode CELL_DCH state do not transmit any data after this
(CELL- timer expires, the RNC transits the UEs to the
WRFD- DCH, CELL_FACH or CELL_PCH state. When LTE-
020500 CELL- enabled UEs in the CELL_DCH state do not transmit
PCH, any data after this timer expires, the RNC transits the
URA- UEs to the CELL_PCH or IDLE state. You can set this
PCH, timer to a value other than 0 if you want to check
CELL- whether FD-enabled UEs and LTE-enabled UEs are in
FACH) the CELL_DCH state.
Fast GUI Value Range: 0~64800
Return Unit: s
from
UMTS Actual Value Range: 0~64800
to LTE Default Value: 4
Enhance
d Fast
Dorman
cy
PsInactT BSC690 SET WRFD- UE State Meaning: This parameter specifies the value of the
mrForPr 0 UPSIN 010202 in CELL-PCH inactivity timer for UEs enabled with the
eFstDrm ACTTI WRFD- Connect Fast Dormancy feature. When detecting that the Fast
MER 020500 ed Mode Dormancy User in PS domain had no data to transfer in
(CELL- CELL-PCH for a long time which longer than this timer,
DCH, the UE is released. To enable this timer, set this timer
CELL- to a value other than 0.
PCH, GUI Value Range: 0~64800
URA-
PCH, Unit: s
CELL- Actual Value Range: 0~64800
FACH) Default Value: 1800
Enhance
d Fast
Dorman
cy
PsInactT BSC691 SET WRFD- UE State Meaning: This parameter specifies the value of the
mrForPr 0 UPSIN 010202 in CELL-PCH inactivity timer for UEs enabled with the
eFstDrm ACTTI WRFD- Connect Fast Dormancy feature. When detecting that the Fast
MER 020500 ed Mode Dormancy User in PS domain had no data to transfer in
(CELL- CELL-PCH for a long time which longer than this timer,
DCH, the UE is released. To enable this timer, set this timer
CELL- to a value other than 0.
PCH, GUI Value Range: 0~64800
URA-
PCH, Unit: s
CELL- Actual Value Range: 0~64800
FACH) Default Value: 1800
Enhance
d Fast
Dorman
cy
TvmThd BSC690 SET WRFD- UE State Meaning: Load threshold for smart state transition from
ForSmar 0 UUEST 010202 in CELL_PCH or URA_PCH to CELL_DCH. If a UE's
tP2D ATETR Connect data during each transition exceeds this threshold, the
ANS ed Mode RNC transits the UE from CELL_PCH or URA_PCH
(CELL- to CELL_DCH.
DCH, GUI Value Range: 0~65535
CELL-
PCH, Unit: 10byte
URA- Actual Value Range: 0~655350
PCH, Default Value: 51
CELL-
FACH)
TvmThd BSC691 SET WRFD- UE State Meaning: Load threshold for smart state transition from
ForSmar 0 UUEST 010202 in CELL_PCH or URA_PCH to CELL_DCH. If a UE's
tP2D ATETR Connect data during each transition exceeds this threshold, the
ANS ed Mode RNC transits the UE from CELL_PCH or URA_PCH
(CELL- to CELL_DCH.
DCH, GUI Value Range: 0~65535
CELL-
PCH, Unit: 10byte
URA- Actual Value Range: 0~655350
PCH, Default Value: 51
CELL-
FACH)
RLCSD BSC690 SET WRFD- UE State Meaning: Whether the transmitted and
URETR 0 UDPUC 010202 in unacknowledged SDUs in the buffer are retransmitted
ANSMI FGDAT Connect in RLC reestablishment scenarios. Value ON indicates
SSION A ed Mode that these SDUs are retransmitted. Value OFF indicates
(CELL- that these SDUs are discarded.
DCH, GUI Value Range: OFF, ON
CELL-
PCH, Unit: None
URA- Actual Value Range: OFF, ON
PCH, Default Value: OFF
CELL-
FACH)
RLCSD BSC691 SET WRFD- UE State Meaning: Whether the transmitted and
URETR 0 UDPUC 010202 in unacknowledged SDUs in the buffer are retransmitted
ANSMI FGDAT Connect in RLC reestablishment scenarios. Value ON indicates
SSION A ed Mode that these SDUs are retransmitted. Value OFF indicates
(CELL- that these SDUs are discarded.
DCH, GUI Value Range: OFF, ON
CELL-
PCH, Unit: None
URA- Actual Value Range: OFF, ON
PCH, Default Value: OFF
CELL-
FACH)
Manage CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH:
ment This parameter specifies to enable AMR through DRD
DC- two-step procedure function. When SRB is set up on
HSUPA DCH, and "RNC" decides to setup the AMR through
DRD procedure, When the switch is enabled, "RNC"
3C- will execute blind handover to the target cell, and then
HSDPA setup the AMR RBs on the target cell, When the switch
is disabled, "RNC" will setup the AMR RBs on the
target cell directly. 8.
CMP_UU_AMR_SID_MUST_CFG_SWITCH: For
narrowband AMR services, when the switch is on, the
SID frame is always configured; when the switch is not
on, the SID frame is configured on the basis of CN
assignment. 9.
CMP_UU_FDPCH_COMPAT_SWITCH: When the
switch is OFF, if the information element that indicates
the F-DPCH capability of UE exists in the message
"RRC_CONNECT_REQ" or
"RRC_CONNECT_SETUP_CMP", the F-DPCH
capability depends on that indicator. In other case, it
means UE does not support F-DPCH. When the switch
is ON, if the information element that indicates the F-
DPCH capability of UE exists in the message
"RRC_CONNECT_REQ" or
"RRC_CONNECT_SETUP_CMP", the F-DPCH
capability depends on that indicator. If that information
element does not exist, UE supports F-DPCH when all
the conditions meets: a) the version of UE is Release 6.
b) UE supports HS-PDSCH. 10.
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH:
When the switch is on, the RAB assignment request and
the subsequent RB setup procedure proceed if the RLC
AM capabilities of the UE fail to meet the minimum
RLC TX/RX window buffer requirement of the RAB to
be setup. When the switch is not on, the RAB
assignment request is rejected. 11.
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_S
WITCH: When this switch is on, the cell individual
offset (CIO) of the best cell is always set to 0 in the
INTRA-FREQUENCY MEASUREMENT
CONTROL messages. Otherwise, the CIO information
of the best cell is not carried in the INTRA-
FREQUENCY MEASUREMENT CONTROL
messages. 12.
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWI
TCH: When the switch is on, the cell synchronization
information traced by the IOS need to be reported during
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWIT
CH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_S
WITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_S
WITCH, CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_S
WITCH,
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWI
TCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_S
WITCH,
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_RAB_5_CFG_ROHC_SWITCH,
CMP_RAB_6_CFG_ROHC_SWITCH,
CMP_RAB_7_CFG_ROHC_SWITCH,
CMP_RAB_8_CFG_ROHC_SWITCH,
CMP_RAB_9_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH
Unit: None
Actual Value Range:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_S
WITCH,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITC
H,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWIT
CH, CMP_IUR_SHO_DIVCTRL_SWITCH,
CMP_UU_ADJACENT_FREQ_CM_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_UU_AMR_SID_MUST_CFG_SWITCH,
CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_S
WITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWI
TCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWIT
CH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_S
WITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_S
WITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_RAB_5_CFG_ROHC_SWITCH,
CMP_RAB_6_CFG_ROHC_SWITCH,
CMP_RAB_7_CFG_ROHC_SWITCH,
CMP_RAB_8_CFG_ROHC_SWITCH,
CMP_RAB_9_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH,
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH,
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH
Default Value:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH:
0,CMP_IU_QOS_ASYMMETRY_IND_COMPAT_S
WITCH:
0,CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWIT
CH:
0,CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SW
ITCH:0,CMP_IUR_SHO_DIVCTRL_SWITCH:
0,CMP_UU_ADJACENT_FREQ_CM_SWITCH:
0,CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH
:1,CMP_UU_AMR_SID_MUST_CFG_SWITCH:
0,CMP_UU_FDPCH_COMPAT_SWITCH:
0,CMP_UU_IGNORE_UE_RLC_CAP_SWITCH:
1,CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_
SWITCH:
0,CMP_UU_IOS_CELL_SYNC_INFO_REPORT_S
WITCH:
0,CMP_UU_SERV_CELL_CHG_WITH_ASU_SWI
TCH:
0,CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_
SWITCH:
1,CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_S
WITCH:
1,CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH:
0,CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH:
0,CMP_RAB_5_CFG_ROHC_SWITCH:
0,CMP_RAB_6_CFG_ROHC_SWITCH:
0,CMP_RAB_7_CFG_ROHC_SWITCH:
0,CMP_RAB_8_CFG_ROHC_SWITCH:
0,CMP_RAB_9_CFG_ROHC_SWITCH:
0,CMP_HSUPA_MACD_FLOW_MUL_SWITCH:
0,CMP_SMLC_RSLT_MODE_TYPE_SWITCH:
Manage CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH:
ment This parameter specifies to enable AMR through DRD
DC- two-step procedure function. When SRB is set up on
HSUPA DCH, and "RNC" decides to setup the AMR through
DRD procedure, When the switch is enabled, "RNC"
3C- will execute blind handover to the target cell, and then
HSDPA setup the AMR RBs on the target cell, When the switch
is disabled, "RNC" will setup the AMR RBs on the
target cell directly. 8.
CMP_UU_AMR_SID_MUST_CFG_SWITCH: For
narrowband AMR services, when the switch is on, the
SID frame is always configured; when the switch is not
on, the SID frame is configured on the basis of CN
assignment. 9.
CMP_UU_FDPCH_COMPAT_SWITCH: When the
switch is OFF, if the information element that indicates
the F-DPCH capability of UE exists in the message
"RRC_CONNECT_REQ" or
"RRC_CONNECT_SETUP_CMP", the F-DPCH
capability depends on that indicator. In other case, it
means UE does not support F-DPCH. When the switch
is ON, if the information element that indicates the F-
DPCH capability of UE exists in the message
"RRC_CONNECT_REQ" or
"RRC_CONNECT_SETUP_CMP", the F-DPCH
capability depends on that indicator. If that information
element does not exist, UE supports F-DPCH when all
the conditions meets: a) the version of UE is Release 6.
b) UE supports HS-PDSCH. 10.
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH:
When the switch is on, the RAB assignment request and
the subsequent RB setup procedure proceed if the RLC
AM capabilities of the UE fail to meet the minimum
RLC TX/RX window buffer requirement of the RAB to
be setup. When the switch is not on, the RAB
assignment request is rejected. 11.
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_S
WITCH: When this switch is on, the cell individual
offset (CIO) of the best cell is always set to 0 in the
INTRA-FREQUENCY MEASUREMENT
CONTROL messages. Otherwise, the CIO information
of the best cell is not carried in the INTRA-
FREQUENCY MEASUREMENT CONTROL
messages. 12.
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWI
TCH: When the switch is on, the cell synchronization
information traced by the IOS need to be reported during
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWIT
CH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_S
WITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_S
WITCH, CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_S
WITCH,
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWI
TCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_S
WITCH,
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_RAB_5_CFG_ROHC_SWITCH,
CMP_RAB_6_CFG_ROHC_SWITCH,
CMP_RAB_7_CFG_ROHC_SWITCH,
CMP_RAB_8_CFG_ROHC_SWITCH,
CMP_RAB_9_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH
Unit: None
Actual Value Range:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_S
WITCH,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITC
H,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWIT
CH, CMP_IUR_SHO_DIVCTRL_SWITCH,
CMP_UU_ADJACENT_FREQ_CM_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_UU_AMR_SID_MUST_CFG_SWITCH,
CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_S
WITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWI
TCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWIT
CH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_S
WITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_S
WITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_RAB_5_CFG_ROHC_SWITCH,
CMP_RAB_6_CFG_ROHC_SWITCH,
CMP_RAB_7_CFG_ROHC_SWITCH,
CMP_RAB_8_CFG_ROHC_SWITCH,
CMP_RAB_9_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH,
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH,
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH
Default Value:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH:
0,CMP_IU_QOS_ASYMMETRY_IND_COMPAT_S
WITCH:
0,CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWIT
CH:
0,CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SW
ITCH:0,CMP_IUR_SHO_DIVCTRL_SWITCH:
0,CMP_UU_ADJACENT_FREQ_CM_SWITCH:
0,CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH
:1,CMP_UU_AMR_SID_MUST_CFG_SWITCH:
0,CMP_UU_FDPCH_COMPAT_SWITCH:
0,CMP_UU_IGNORE_UE_RLC_CAP_SWITCH:
1,CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_
SWITCH:
0,CMP_UU_IOS_CELL_SYNC_INFO_REPORT_S
WITCH:
0,CMP_UU_SERV_CELL_CHG_WITH_ASU_SWI
TCH:
0,CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_
SWITCH:
1,CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_S
WITCH:
1,CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH:
0,CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH:
0,CMP_RAB_5_CFG_ROHC_SWITCH:
0,CMP_RAB_6_CFG_ROHC_SWITCH:
0,CMP_RAB_7_CFG_ROHC_SWITCH:
0,CMP_RAB_8_CFG_ROHC_SWITCH:
0,CMP_RAB_9_CFG_ROHC_SWITCH:
0,CMP_HSUPA_MACD_FLOW_MUL_SWITCH:
0,CMP_SMLC_RSLT_MODE_TYPE_SWITCH:
PsInactT BSC690 SET WRFD- 3.4/6.8/1 Meaning: When detecting that the Ps' Conversational
mrForC 0 UPSIN 010510 3.6/27.2 User had no data to transfer for a long time which longer
on ACTTI WRFD- Kbps than this timer, the PDCP layer would request the RRC
MER 140226 RRC layer to release this Radio Access Bear.
Connect GUI Value Range: 0~14400
ion and
Radio Unit: s
Access Actual Value Range: 0~14400
Bearer Default Value: 20
Establis
hment
and
Release
Fast
Return
from
UMTS
to LTE
PsInactT BSC691 SET WRFD- 3.4/6.8/1 Meaning: When detecting that the Ps' Conversational
mrForC 0 UPSIN 010510 3.6/27.2 User had no data to transfer for a long time which longer
on ACTTI WRFD- Kbps than this timer, the PDCP layer would request the RRC
MER 140226 RRC layer to release this Radio Access Bear.
Connect GUI Value Range: 0~14400
ion and
Radio Unit: s
Access Actual Value Range: 0~14400
Bearer Default Value: 20
Establis
hment
and
Release
Fast
Return
from
UMTS
to LTE
ProtectT BSC690 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForC 0 UPSIN 010202 in if the Conversational Radio Access Bear haven't been
on ACTTI WRFD- Connect released until the Conversational service T2 timeout, the
MER 010510 ed Mode PDCP layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
ProtectT BSC691 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForC 0 UPSIN 010202 in if the Conversational Radio Access Bear haven't been
on ACTTI WRFD- Connect released until the Conversational service T2 timeout, the
MER 010510 ed Mode PDCP layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
PsInactT BSC690 SET WRFD- UE State Meaning: When detecting that the Ps' Streaming User
mrForSt 0 UPSIN 010202 in had no data to transfer for a long time which longer than
r ACTTI WRFD- Connect this timer, the PDCP layer would request the RRC layer
MER 010510 ed Mode to release this Radio Access Bear.
(CELL- GUI Value Range: 0~14400
WRFD- DCH,
140226 CELL- Unit: s
PCH, Actual Value Range: 0~14400
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
Fast
Return
from
UMTS
to LTE
PsInactT BSC691 SET WRFD- UE State Meaning: When detecting that the Ps' Streaming User
mrForSt 0 UPSIN 010202 in had no data to transfer for a long time which longer than
r ACTTI WRFD- Connect this timer, the PDCP layer would request the RRC layer
MER 010510 ed Mode to release this Radio Access Bear.
(CELL- GUI Value Range: 0~14400
WRFD- DCH,
140226 CELL- Unit: s
PCH, Actual Value Range: 0~14400
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
Fast
Return
from
UMTS
to LTE
ProtectT BSC690 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForSt 0 UPSIN 010202 in if the Streaming Radio Access Bear haven't been
r ACTTI WRFD- Connect released until the Streaming service T2 timeout, the
MER 010510 ed Mode PDCP layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
ProtectT BSC691 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForSt 0 UPSIN 010202 in if the Streaming Radio Access Bear haven't been
r ACTTI WRFD- Connect released until the Streaming service T2 timeout, the
MER 010510 ed Mode PDCP layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
PsInactT BSC690 SET WRFD- Intra Meaning: When detecting that the Ps' Interactive User
mrForIn 0 UPSIN 010901 RNC had no data to transfer for a long time which longer than
t ACTTI WRFD- URA this timer, the PDCP layer would request the RRC layer
MER 010510 Update to release this Radio Access Bear.
ACH,
CELL_
DCH
State
(Type 2)
Inter
RNC
Cell
Update
Paging
UE in
Idle,
CELL_P
CH,
URA_P
CH State
(Type 1)
PsInactT BSC691 SET WRFD- Intra Meaning: When detecting that the Ps' Interactive User
mrForIn 0 UPSIN 010901 RNC had no data to transfer for a long time which longer than
t ACTTI WRFD- URA this timer, the PDCP layer would request the RRC layer
MER 010510 Update to release this Radio Access Bear.
ACH,
CELL_
DCH
State
(Type 2)
Inter
RNC
Cell
Update
Paging
UE in
Idle,
CELL_P
CH,
URA_P
CH State
(Type 1)
ProtectT BSC690 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForIn 0 UPSIN 010202 in if the Interactive Radio Access Bear haven't been
t ACTTI WRFD- Connect released until the Interactive service T2 timeout, the
MER 010510 ed Mode PDCP layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
ProtectT BSC691 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForIn 0 UPSIN 010202 in if the Interactive Radio Access Bear haven't been
t ACTTI WRFD- Connect released until the Interactive service T2 timeout, the
MER 010510 ed Mode PDCP layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
PsInactT BSC690 SET WRFD- UE State Meaning: When detecting that the Ps' Background User
mrForB 0 UPSIN 010202 in had no data to transfer for a long time which longer than
ac ACTTI WRFD- Connect this timer, the PDCP layer would request the RRC layer
MER 010510 ed Mode to release this Radio Access Bear.
(CELL- GUI Value Range: 0~14400
WRFD- DCH,
140226 CELL- Unit: s
PCH, Actual Value Range: 0~14400
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
Fast
Return
from
UMTS
to LTE
PsInactT BSC691 SET WRFD- UE State Meaning: When detecting that the Ps' Background User
mrForB 0 UPSIN 010202 in had no data to transfer for a long time which longer than
ac ACTTI WRFD- Connect this timer, the PDCP layer would request the RRC layer
MER 010510 ed Mode to release this Radio Access Bear.
(CELL- GUI Value Range: 0~14400
WRFD- DCH,
140226 CELL- Unit: s
PCH, Actual Value Range: 0~14400
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
Fast
Return
from
UMTS
to LTE
ProtectT BSC690 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForB 0 UPSIN 010202 in if the Background Radio Access Bear haven't been
ac ACTTI WRFD- Connect released until the Background service T2 timeout, the
MER 010510 ed Mode PDCP layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
ProtectT BSC691 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForB 0 UPSIN 010202 in if the Background Radio Access Bear haven't been
ac ACTTI WRFD- Connect released until the Background service T2 timeout, the
MER 010510 ed Mode PDCP layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
PSInact BSC690 SET WRFD- UE State Meaning: When detecting that the Ps' IMS signal had
TmrForI 0 UPSIN 010202 in no data to transfer for a long time which longer than this
msSig ACTTI WRFD- Connect timer, the PDCP layer would request the RRC layer to
MER 010510 ed Mode release this Radio Access Bear.
(CELL- GUI Value Range: 0~64800
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~64800
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
PSInact BSC691 SET WRFD- UE State Meaning: When detecting that the Ps' IMS signal had
TmrForI 0 UPSIN 010202 in no data to transfer for a long time which longer than this
msSig ACTTI WRFD- Connect timer, the PDCP layer would request the RRC layer to
MER 010510 ed Mode release this Radio Access Bear.
(CELL- GUI Value Range: 0~64800
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~64800
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
ProtectT BSC690 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForI 0 UPSIN 010202 in if the IMS Radio Access Bear for signal haven't been
msSig ACTTI WRFD- Connect released until the IMS service T2 timeout, the PDCP
MER 010510 ed Mode layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
ProtectT BSC691 SET WRFD- UE State Meaning: After sending release request to RRC layer,
mrForI 0 UPSIN 010202 in if the IMS Radio Access Bear for signal haven't been
msSig ACTTI WRFD- Connect released until the IMS service T2 timeout, the PDCP
MER 010510 ed Mode layer will resend release request indication.
(CELL- GUI Value Range: 0~60
DCH,
CELL- Unit: s
PCH, Actual Value Range: 0~60
URA- Default Value: 20
PCH,
CELL-
FACH)
3.4/6.8/1
3.6/27.2
Kbps
RRC
Connect
ion and
Radio
Access
Bearer
Establis
hment
and
Release
TAC BSC690 ADD WRFD- Termina Meaning: Type Allocation Code (TAC) is proportion of
0 UIMEIT 160103 l Black the International Mobile Station Equipment Identity
AC WRFD- List (IMEI) and represent the first eight digits of the IMEI.
MOD 020500 Enhance TAC is used to differentiate between the MSs of
UIMEIT d Fast different models. This parameter consists of an eight
AC Dorman digit string. If the string is less than eight digits, the
cy system fills the higher orders with 0s to achieve an eight
RMV digit string.
UIMEIT
AC GUI Value Range: 0~99999999
Unit: None
Actual Value Range: 0~99999999
Default Value: None
TAC BSC691 ADD WRFD- Termina Meaning: Type Allocation Code (TAC) is proportion of
0 UIMEIT 160103 l Black the International Mobile Station Equipment Identity
AC WRFD- List (IMEI) and represent the first eight digits of the IMEI.
MOD 020500 Enhance TAC is used to differentiate between the MSs of
UIMEIT d Fast different models. This parameter consists of an eight
AC Dorman digit string. If the string is less than eight digits, the
cy system fills the higher orders with 0s to achieve an eight
RMV digit string.
UIMEIT
AC GUI Value Range: 0~99999999
Unit: None
Actual Value Range: 0~99999999
Default Value: None
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWIT
CH
(AM_D2F_F2D_RESTMR_OPTIMIZATION_SWIT
CH), D2P_DT_MSG_BUFFER_SWITCH
(D2P_DT_MSG_BUFFER_SWITCH),
CM_CODE_CONFLICT_OPT_SWITCH
(CM_CODE_CONFLICT_OPT_SWITCH),
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH
(H_SERV_CELL_CHANGE_MSG_OPT_SWITCH),
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH
(FAST_HSDPA_SERV_CELL_CHANGE_SWITCH
),
RLRST_ASU_SUCC_COUNTERS_CORRECT_SW
ITCH
(RLRST_ASU_SUCC_COUNTERS_CORRECT_S
WITCH),
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH
(COUNT_STATE_CHG_BY_RAB_EHN_SWITCH),
RAB_RELATED_COUNTER_OPT_SWITCH
(RAB_RELATED_COUNTER_OPT_SWITCH),
CELLUPDATE_PROCEDURE_OPT_SWITCH
(CELLUPDATE_PROCEDURE_OPT_SWITCH),
PTT_PAGING_PRD_CRRCT_SWITCH
(PTT_PAGING_PRD_CRRCT_SWITCH),
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWIT
CH
(RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWIT
CH), L2U_UP_DELAY_OPT_SWITCH
(L2U_UP_DELAY_OPT_SWITCH),
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWI
TCH
(PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SW
ITCH)
Unit: None
Actual Value Range:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH,
RL_REEST_PS_ON_FACH_SWITCH,
CELLUPDATE_MEASUREMENT_OPT_SWITCH,
D2F_PROCEDURE_OPTIMIZATION_SWITCH,
F2D_PROCEDURE_OPTIMIZATION_SWITCH,
FOREVER_PCH_CTRL_PLANE_SHARE_OPT,
FOREVER_PCH_USER_PLANE_SHARE_OPT,
RAB_REL_SRV_CELL_CHG_CROSS_SWITCH,
SCRIWITHCAUSE_OVERLAP_SWITCH,
P2F_CUC_REPEAT_SWITCH,
UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH
,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITC
H,
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWIT
CH, D2P_DT_MSG_BUFFER_SWITCH,
CM_CODE_CONFLICT_OPT_SWITCH,
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH,
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH,
RLRST_ASU_SUCC_COUNTERS_CORRECT_SW
ITCH,
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH,
RAB_RELATED_COUNTER_OPT_SWITCH,
CELLUPDATE_PROCEDURE_OPT_SWITCH,
PTT_PAGING_PRD_CRRCT_SWITCH,
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWIT
CH, L2U_UP_DELAY_OPT_SWITCH,
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWI
TCH
Default Value:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH:
1,RL_REEST_PS_ON_FACH_SWITCH:
0,CELLUPDATE_MEASUREMENT_OPT_SWITC
H:
0,D2F_PROCEDURE_OPTIMIZATION_SWITCH:
0,F2D_PROCEDURE_OPTIMIZATION_SWITCH:
0,FOREVER_PCH_CTRL_PLANE_SHARE_OPT:
0,FOREVER_PCH_USER_PLANE_SHARE_OPT:
0,RAB_REL_SRV_CELL_CHG_CROSS_SWITCH:
0,SCRIWITHCAUSE_OVERLAP_SWITCH:
0,P2F_CUC_REPEAT_SWITCH:
0,UU_ABN_REL_INFO_NOTIFY_NODEB_SWITC
H:
0,D2F_AM_PROCEDURE_OPTIMIZATION_SWIT
CH:
0,AM_D2F_F2D_RESTMR_OPTIMIZATION_SWI
TCH:0,D2P_DT_MSG_BUFFER_SWITCH:
0,CM_CODE_CONFLICT_OPT_SWITCH:
1,H_SERV_CELL_CHANGE_MSG_OPT_SWITCH:
0,FAST_HSDPA_SERV_CELL_CHANGE_SWITC
H:
0,RLRST_ASU_SUCC_COUNTERS_CORRECT_S
WITCH:
0,COUNT_STATE_CHG_BY_RAB_EHN_SWITCH
:0,RAB_RELATED_COUNTER_OPT_SWITCH:
0,CELLUPDATE_PROCEDURE_OPT_SWITCH:
1,PTT_PAGING_PRD_CRRCT_SWITCH:
RNC_P2D_DRD_SWITCH
(RNC_P2D_DRD_SWITCH), P2D_SWITCH
(P2D_SWITCH),
AMR_F2D_OVERLAP_CELLUPT_SWITCH
(AMR_F2D_OVERLAP_CELLUPT_SWITCH),
SRB_RESET_RL_SETUP_SWITCH
(SRB_RESET_RL_SETUP_SWITCH),
RLFAIL_RL_SETUP_SWITCH
(RLFAIL_RL_SETUP_SWITCH),
CS_RL_SETUP_SWITCH
(CS_RL_SETUP_SWITCH),
PS_RL_SETUP_SWITCH
(PS_RL_SETUP_SWITCH),
UE_SRB_RESET_SWITCH
(UE_SRB_RESET_SWITCH),
RL_RESTORE_SWITCH
(RL_RESTORE_SWITCH),
RNC_EFD_D2F_SWITCH
(RNC_EFD_D2F_SWITCH),
RNC_RB_SCRI_NOT_DROP_SWITCH
(RNC_RB_SCRI_NOT_DROP_SWITCH),
RRC_RECONN_SWITCH
(RRC_RECONN_SWITCH),
RRC_REPEAT_PFM_SWITCH
(RRC_REPEAT_PFM_SWITCH),
F2D_NO_RSP_RRCREL_SWITCH
(F2D_NO_RSP_RRCREL_SWITCH),
CS_SETUP_P2D_SWITCH
(CS_SETUP_P2D_SWITCH),
SYSHO_CIPHER_IE_SWITCH
(SYSHO_CIPHER_IE_SWITCH),
P2P_GTPU_NOT_CFG_SWITCH
(P2P_GTPU_NOT_CFG_SWITCH),
RB_SETUP_CIPHER_TIME_ADJ_SWITCH
(RB_SETUP_CIPHER_TIME_ADJ_SWITCH),
CS_PRI_MOD_NOT_INT_SWITCH
(CS_PRI_MOD_NOT_INT_SWITCH),
RAB_SETUP_TMSI_REALLOC_BUF_SWITCH
(RAB_SETUP_TMSI_REALLOC_BUF_SWITCH),
IU_FAULT_REL_PS_RES_SWITCH
(IU_FAULT_REL_PS_RES_SWITCH),
RB_RECFG_RL_REEST_SWITCH
(RB_RECFG_RL_REEST_SWITCH),
F2P_DT_MSG_BUFFER_SWITCH
(F2P_DT_MSG_BUFFER_SWITCH),
SCRI_COMPATIBLE_SWITCH
(SCRI_COMPATIBLE_SWITCH),
GTPU_ERR_IND_DEF_SWITCH
(GTPU_ERR_IND_DEF_SWITCH),
IUR_SRV_CELL_CHG_MACHS_RESET_SWITCH
(IUR_SRV_CELL_CHG_MACHS_RESET_SWITC
H), UL_INTEG_ALGO_COMPAT_SWITCH
(UL_INTEG_ALGO_COMPAT_SWITCH)
Unit: None
Actual Value Range:
PAGGING_NUM_CTRL_SWITCH,
ASU_RL_RESET_SWITCH,
MC_RL_RESET_SWITCH,
FD_PCH_REENTERSA_FORCE_RRC_REL_SWIT
CH, UE_CRC_COMPATIBLE_SWITCH,
RNC_P2D_DRD_SWITCH, P2D_SWITCH,
AMR_F2D_OVERLAP_CELLUPT_SWITCH,
SRB_RESET_RL_SETUP_SWITCH,
RLFAIL_RL_SETUP_SWITCH,
CS_RL_SETUP_SWITCH,
PS_RL_SETUP_SWITCH,
UE_SRB_RESET_SWITCH,
RL_RESTORE_SWITCH,
RNC_EFD_D2F_SWITCH,
RNC_RB_SCRI_NOT_DROP_SWITCH,
RRC_RECONN_SWITCH,
RRC_REPEAT_PFM_SWITCH,
F2D_NO_RSP_RRCREL_SWITCH,
CS_SETUP_P2D_SWITCH,
SYSHO_CIPHER_IE_SWITCH,
P2P_GTPU_NOT_CFG_SWITCH,
RB_SETUP_CIPHER_TIME_ADJ_SWITCH,
CS_PRI_MOD_NOT_INT_SWITCH,
RAB_SETUP_TMSI_REALLOC_BUF_SWITCH,
IU_FAULT_REL_PS_RES_SWITCH,
RB_RECFG_RL_REEST_SWITCH,
F2P_DT_MSG_BUFFER_SWITCH,
SCRI_COMPATIBLE_SWITCH,
GTPU_ERR_IND_DEF_SWITCH,
IUR_SRV_CELL_CHG_MACHS_RESET_SWITCH
, UL_INTEG_ALGO_COMPAT_SWITCH
Default Value: PAGGING_NUM_CTRL_SWITCH:
0,ASU_RL_RESET_SWITCH:
0,MC_RL_RESET_SWITCH:
0,FD_PCH_REENTERSA_FORCE_RRC_REL_SWI
TCH:0,UE_CRC_COMPATIBLE_SWITCH:
0,RNC_P2D_DRD_SWITCH:0,P2D_SWITCH:
0,AMR_F2D_OVERLAP_CELLUPT_SWITCH:
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWIT
CH
(AM_D2F_F2D_RESTMR_OPTIMIZATION_SWIT
CH), D2P_DT_MSG_BUFFER_SWITCH
(D2P_DT_MSG_BUFFER_SWITCH),
CM_CODE_CONFLICT_OPT_SWITCH
(CM_CODE_CONFLICT_OPT_SWITCH),
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH
(H_SERV_CELL_CHANGE_MSG_OPT_SWITCH),
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH
(FAST_HSDPA_SERV_CELL_CHANGE_SWITCH
),
RLRST_ASU_SUCC_COUNTERS_CORRECT_SW
ITCH
(RLRST_ASU_SUCC_COUNTERS_CORRECT_S
WITCH),
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH
(COUNT_STATE_CHG_BY_RAB_EHN_SWITCH),
RAB_RELATED_COUNTER_OPT_SWITCH
(RAB_RELATED_COUNTER_OPT_SWITCH),
CELLUPDATE_PROCEDURE_OPT_SWITCH
(CELLUPDATE_PROCEDURE_OPT_SWITCH),
PTT_PAGING_PRD_CRRCT_SWITCH
(PTT_PAGING_PRD_CRRCT_SWITCH),
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWIT
CH
(RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWIT
CH), L2U_UP_DELAY_OPT_SWITCH
(L2U_UP_DELAY_OPT_SWITCH),
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWI
TCH
(PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SW
ITCH)
Unit: None
Actual Value Range:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH,
RL_REEST_PS_ON_FACH_SWITCH,
CELLUPDATE_MEASUREMENT_OPT_SWITCH,
D2F_PROCEDURE_OPTIMIZATION_SWITCH,
F2D_PROCEDURE_OPTIMIZATION_SWITCH,
FOREVER_PCH_CTRL_PLANE_SHARE_OPT,
FOREVER_PCH_USER_PLANE_SHARE_OPT,
RAB_REL_SRV_CELL_CHG_CROSS_SWITCH,
SCRIWITHCAUSE_OVERLAP_SWITCH,
P2F_CUC_REPEAT_SWITCH,
UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH
,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITC
H,
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWIT
CH, D2P_DT_MSG_BUFFER_SWITCH,
CM_CODE_CONFLICT_OPT_SWITCH,
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH,
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH,
RLRST_ASU_SUCC_COUNTERS_CORRECT_SW
ITCH,
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH,
RAB_RELATED_COUNTER_OPT_SWITCH,
CELLUPDATE_PROCEDURE_OPT_SWITCH,
PTT_PAGING_PRD_CRRCT_SWITCH,
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWIT
CH, L2U_UP_DELAY_OPT_SWITCH,
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWI
TCH
Default Value:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH:
1,RL_REEST_PS_ON_FACH_SWITCH:
0,CELLUPDATE_MEASUREMENT_OPT_SWITC
H:
0,D2F_PROCEDURE_OPTIMIZATION_SWITCH:
0,F2D_PROCEDURE_OPTIMIZATION_SWITCH:
0,FOREVER_PCH_CTRL_PLANE_SHARE_OPT:
0,FOREVER_PCH_USER_PLANE_SHARE_OPT:
0,RAB_REL_SRV_CELL_CHG_CROSS_SWITCH:
0,SCRIWITHCAUSE_OVERLAP_SWITCH:
0,P2F_CUC_REPEAT_SWITCH:
0,UU_ABN_REL_INFO_NOTIFY_NODEB_SWITC
H:
0,D2F_AM_PROCEDURE_OPTIMIZATION_SWIT
CH:
0,AM_D2F_F2D_RESTMR_OPTIMIZATION_SWI
TCH:0,D2P_DT_MSG_BUFFER_SWITCH:
0,CM_CODE_CONFLICT_OPT_SWITCH:
1,H_SERV_CELL_CHANGE_MSG_OPT_SWITCH:
0,FAST_HSDPA_SERV_CELL_CHANGE_SWITC
H:
0,RLRST_ASU_SUCC_COUNTERS_CORRECT_S
WITCH:
0,COUNT_STATE_CHG_BY_RAB_EHN_SWITCH
:0,RAB_RELATED_COUNTER_OPT_SWITCH:
0,CELLUPDATE_PROCEDURE_OPT_SWITCH:
1,PTT_PAGING_PRD_CRRCT_SWITCH:
URA2FACH_OVERLAP_CELLUPT_PROC_SWIT
CH, RB_SETUP_F2D_USE_AM_RLC_SWITCH,
RB_RECFG_D2F_USE_AM_RLC_SWITCH,
RB_RECFG_F2D_USE_AM_RLC_SWITCH,
RRC_UE_USER_SMOOTH_OPT_SWITCH,
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SWITCH,
CPC_OPT_FOR_RLSETUP_SWITCH,
D2P_L2DEACT_FAIL_OPT_SWITCH,
EFACH_RRC_REG_CMP_SWITCH,
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH,
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWIT
CH,
RELOC_IN_RG_COMB_INDEX_ALLOC_SWITC
H, SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITCH,
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SWITCH,
ASYN_RL_REEST_OPT_SWITCH,
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWIT
CH,
URA_PCH_LAC_RAC_CHG_NO_PAGING_SWIT
CH, PAGING_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_USE_CS_KEY_SWITCH,
SOCKET_RECEIVE_DATA_CORRECT_SWITCH,
CU_PRI_OVERLAP_OTHER_PROC_SWITCH,
INTERRAT2U_INTEG_PROTECT_OPT_SWITCH,
INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH
, DRNC_RL_PARA_UPT_OPT_SWITCH
Default Value:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH:
0,RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_
SWITCH:0,DRNC_RL_REEST_OPT_SWITCH:
1,URA2FACH_OVERLAP_CELLUPT_PROC_SWI
TCH:0,RB_SETUP_F2D_USE_AM_RLC_SWITCH:
0,RB_RECFG_D2F_USE_AM_RLC_SWITCH:
0,RB_RECFG_F2D_USE_AM_RLC_SWITCH:
0,RRC_UE_USER_SMOOTH_OPT_SWITCH:
1,TRNC_LOAD_CTRL_SWITCH:
0,IU_SIG_REL_PCH_PAGING_SWITCH:
0,CPC_OPT_FOR_RLSETUP_SWITCH:
1,D2P_L2DEACT_FAIL_OPT_SWITCH:
0,EFACH_RRC_REG_CMP_SWITCH:
0,P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITC
H:
0,AMRC_ON_122_AMR_HHO_ROLL_BACK_SWI
TCH:
0,RELOC_IN_RG_COMB_INDEX_ALLOC_SWIT
CH:0,SCM_CU_CROSS_SWITCH:
0,DRNC_HSPA_CM_OPT_SWITCH:
0,IUB_TRANSID_OPT_SWITCH:
0,L2_ENHENCE_RECFG_OPT_SWITCH:
0,ASYN_RL_REEST_OPT_SWITCH:
0,RNC_IMSI_HO_OPT_SWITCH:
0,IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWI
TCH:
0,URA_PCH_LAC_RAC_CHG_NO_PAGING_SWI
TCH:0,PAGING_OVERLAP_CU_OPT_SWITCH:
0,SRVCC_RELOC_IN_USE_CS_KEY_SWITCH:
1,SOCKET_RECEIVE_DATA_CORRECT_SWITC
H:1,CU_PRI_OVERLAP_OTHER_PROC_SWITCH:
0,INTERRAT2U_INTEG_PROTECT_OPT_SWITC
H:
0,INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITC
H:0,DRNC_RL_PARA_UPT_OPT_SWITCH:1
URA2FACH_OVERLAP_CELLUPT_PROC_SWIT
CH, RB_SETUP_F2D_USE_AM_RLC_SWITCH,
RB_RECFG_D2F_USE_AM_RLC_SWITCH,
RB_RECFG_F2D_USE_AM_RLC_SWITCH,
RRC_UE_USER_SMOOTH_OPT_SWITCH,
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SWITCH,
CPC_OPT_FOR_RLSETUP_SWITCH,
D2P_L2DEACT_FAIL_OPT_SWITCH,
EFACH_RRC_REG_CMP_SWITCH,
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH,
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWIT
CH,
RELOC_IN_RG_COMB_INDEX_ALLOC_SWITC
H, SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITCH,
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SWITCH,
ASYN_RL_REEST_OPT_SWITCH,
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWIT
CH,
URA_PCH_LAC_RAC_CHG_NO_PAGING_SWIT
CH, PAGING_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_USE_CS_KEY_SWITCH,
SOCKET_RECEIVE_DATA_CORRECT_SWITCH,
CU_PRI_OVERLAP_OTHER_PROC_SWITCH,
INTERRAT2U_INTEG_PROTECT_OPT_SWITCH,
INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH
, DRNC_RL_PARA_UPT_OPT_SWITCH
Default Value:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH:
0,RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_
SWITCH:0,DRNC_RL_REEST_OPT_SWITCH:
1,URA2FACH_OVERLAP_CELLUPT_PROC_SWI
TCH:0,RB_SETUP_F2D_USE_AM_RLC_SWITCH:
0,RB_RECFG_D2F_USE_AM_RLC_SWITCH:
0,RB_RECFG_F2D_USE_AM_RLC_SWITCH:
0,RRC_UE_USER_SMOOTH_OPT_SWITCH:
1,TRNC_LOAD_CTRL_SWITCH:
0,IU_SIG_REL_PCH_PAGING_SWITCH:
0,CPC_OPT_FOR_RLSETUP_SWITCH:
1,D2P_L2DEACT_FAIL_OPT_SWITCH:
0,EFACH_RRC_REG_CMP_SWITCH:
0,P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITC
H:
0,AMRC_ON_122_AMR_HHO_ROLL_BACK_SWI
TCH:
0,RELOC_IN_RG_COMB_INDEX_ALLOC_SWIT
CH:0,SCM_CU_CROSS_SWITCH:
0,DRNC_HSPA_CM_OPT_SWITCH:
0,IUB_TRANSID_OPT_SWITCH:
0,L2_ENHENCE_RECFG_OPT_SWITCH:
0,ASYN_RL_REEST_OPT_SWITCH:
0,RNC_IMSI_HO_OPT_SWITCH:
0,IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWI
TCH:
0,URA_PCH_LAC_RAC_CHG_NO_PAGING_SWI
TCH:0,PAGING_OVERLAP_CU_OPT_SWITCH:
0,SRVCC_RELOC_IN_USE_CS_KEY_SWITCH:
1,SOCKET_RECEIVE_DATA_CORRECT_SWITC
H:1,CU_PRI_OVERLAP_OTHER_PROC_SWITCH:
0,INTERRAT2U_INTEG_PROTECT_OPT_SWITC
H:
0,INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITC
H:0,DRNC_RL_PARA_UPT_OPT_SWITCH:1
9 Counters
10 Glossary
11 Reference Documents