Académique Documents
Professionnel Documents
Culture Documents
Date : 2007-10-26
ENGINEERING CENTER
BERLIN GECB Page : 1/23
GECB
Owners Information Manual
Authorization Date:
Document Revision :
CONTENTS
1 SERVICE TOOL TREE STRUCTURE ............................................................................................................ 3
9 APPENDIX..................................................................................................................................................... 20
9.1 EVENT LOGGING .......................................................................................................................................... 20
2 Status display
BY Drive BY-Relay
BRK BR-Relay
8 Info messages
9 Appendix
0110 Stuck RDCB F Rear Door Close Button contact permanent active
0201 Correct.Run I A correction run was performed (e.g. after INS, NAV)
0202 /ES in FR W ES-input was activated during Fast Run
0203 /ES in SR W ES-input was activated during Slow Run
0204 TCI/ERO on I TCI or ERO has been switched on
0205 SE-Fault F The car cannot start due to missing SE-signal
Check the door bypass
0210 /DZ in NST F DZ-signal was lost or not detected at all after having stopped
0211 /DFC in FR W car door has been opened during Fast Run
0212 /DFC in SR W car door has been opened during Slow Run
0213 DrvPrepErr W Prepare To Run expected from Drive
(e.g. missing load weighing information for ABL)
0214 DrvStuckPtr W Drive stuck in Prepare To Run
0215 DrvStuckRtr W Drive stuck in Ready To Run (No Abl)
0216 DrvBrakeErr F Brake not lifted.
0217 DrvCreepErr F Drive Creep time too long.
0218 DrvShutdown F The drive reports a Shutdown
See event logging of MCB.
0219 DrvStartErr F
0220 DrvService W The drive requested “Request For Service” (REM). See drive
event logging for reason.
0222 1TH-Fault W The DBR-contact which is connected to the input 1TH is
opened. The drive is powered down to allow cooling.
0223 2TH-Fault F One of the contacts which is connected to the 2TH is opened.
0224 DrvEndRun F Drive did not end the run.
0225 110VAC dead F 110VAC is dead for 5 seconds
0228 1LS+2LS on F Limit switches 1LS and 2LS are active at the same time.
Check power supply of the position reference system.
0230 RSL Adr Chk F Some RSL I/Os have to be programmed to a valid address and
are not allowed to be set to 00-0 or 01-0. Currently only one I/O
is checked:
691 – TCI
Set I/O 691 to a valid address
0233 PowerSave I The drive package has been powered on
0237 /DW in FR W landing door has been opened during Fast Run
0238 /DW in SR W landing door has been opened during Slow Run
0300 DBP: dfc_SE F While the door was opening or fully opened, the door bypass
was found to be inactive (DFC low or SE high)
0301 DCL in [ ] F (R)DCL was active while the door was fully opened
This event is not logged within the first 40 seconds after system
startup.
0306 Hwy Access F Landing Door was opened or the car door is bridged.
see description for blinking message 'Switch INS'
0307 RDOL:alw.on F RDOL was active while the door was fully closed. This event is
also logged when the fuses of the door system are burned.
This event is not logged within the first 40 seconds after system
startup.
0308 DOOR sync F Multidrop synchronization error
0309 DOOR adr. F Multidrop unused message origin
0310 FDOOR chk F Multidrop front door checksum error
0311 RDOOR chk F Multidrop rear door checksum error
0312 FDOOR reply F Multidrop front door communication timeout (>200ms)
0313 RDOOR reply F Multidrop rear door communication timeout (>200ms)
0314 GDS noPull F GDS relay not pulled
0315 GDS noDrop F GDS relay not dropped
0319 GSM Error F GSM input error
0400 RSL parity W Two remote stations with the same address are connected to
the same link
0401 RSL sync W Synchronization lost on remote serial link.
Check whether there is a shortcut on the link.
0402 RSL reinit F RSL driver has reported a problem. RSL was reinitialized.
0403 RSL Fail F Application has detected that the RSL driver doesn't run
anymore. Software has been restarted.
0404 RSL Hrtbeat F RSL driver has detected that the application doesn't run
anymore. Software has been restarted.
0405 RSL Board F RSL board mismatch!
0406 Group RSL F Group RSL has failed
0500 RNG1 msg W data error on Duplex/Triplex ring
0501 RNG1 time W no ring messages received from other car for a specific time
0502 RNG1 sio W framing error on Duplex/Triplex ring
0503 RNG1 tx W ring messages couldn't be sent in an appropriate time
0504 RNG1 rxOff W No messages are received within a timeout, and NO BREAK is
detected.
0505 RNG1 reset W Reinitializing RING Service (stm_ring_run expired)
0506 DES offline F DES is not present
0507 GCB offline F no GCB is present