Académique Documents
Professionnel Documents
Culture Documents
Rev.0
Purpose
This document describes how to install full software including OS to F37.
You are strongly requested to perform the update work referring to this document. Otherwise, the
update won’t be successfully completed and this may cause the boot-up failure in the worst case.
Scope
F37 currently running on the system software version from 1.0.0 up to 4.0.0.
Please note that the procedure is different depending on the current software version.
Preparation
Microsoft Windows PC with DVD/Blu-ray drive,
DVD-R/BD-R writing software is installed, available hard disk space is 10Gbytes or more,
virus protection software with the latest virus definition file is installed and the latest OS
updates/patches are applied.
Portable USB Blu-ray or DVD drive (Pioneer, BDR-XD05 series are recommended)
Page 1 of 33
F37 Software Installation Procedure, Rev.0
Page 2 of 33
F37 Software Installation Procedure, Rev.0
The window like a picture shown right appears and starts disk
writing. DV-F37-12-1-1.iso
Verifying disc…
Page 3 of 33
F37 Software Installation Procedure, Rev.0
DV-F37-12-1-1 BD-F37-13-1-1
WORK
The software installation disk to be used on the next page and after, is different depending on the
current system version on the machine. Please refer to the table below, and prepare correct disk
beforehand.
Current system System version after Media type of software
Disk number
version software installation installation disk
Page 4 of 33
F37 Software Installation Procedure, Rev.0
All data in the HDD will be erased by performing the software full installation. If there is user
data such as stored image, preset on the HDD, please take a data backup beforehand.
The status of option software (SOP) will be kept even if you perform the software full
installation.
Changing BIOS settings Change the BIOS settings so that the machine is
booting-up from software installation disk.
Operation check After restart the machine manually, enter the S/N
information on the maintenance screen, then
restoring the user data if necessary. Perform the
overall operation check.
Page 5 of 33
F37 Software Installation Procedure, Rev.0
You can confirm the machine network configuration from “DICOM-Store, Send”
on the common preset menu.
You can confirm the machine log files from “LOG” on the maintenance screen.
Take a backup of these if necessary.
Printer property settings for digital B/W and color printer (UP-D897 and so on)
Page 6 of 33
F37 Software Installation Procedure, Rev.0
If you find any PC printer on the pull-down menu under the “Printer Property” on
the maintenance menu – OTHER, some software driver for PC printer was installed
on this machine.
If you find version information under the “McAfee Solidifier” on the maintenance
menu- SECURITY, the McAfee Embedded Control software was installed on this
machine.
OB Measurement setting
You can confirm the OB Measurement setting on SYSTEM1 screen from
maintenance menu.
Page 7 of 33
F37 Software Installation Procedure, Rev.0
Do not turn the machine off / Do not remove the USB device during accessing the hard
disk and/or the USB device.
When you connect some USB device into the machine, disconnect them before update
work.
(1) Follow the instruction below to set the machine to the maintenance mode.
Turn the machine off.
Remove the right side cover and main chassis cover, and then change the maintenance Dip SW
as below.
SW
1 2
(2) Connect USB portable Blu-ray (or DVD) drive to the machine.
Use any USB port J304 though J308 (In the photo below, these are J304 and J305).
USB portable
DVD drive
Page 8 of 33
F37 Software Installation Procedure, Rev.0
(3) Insert the created software installation disk that is created at previous step into the connected
USB drive. Change the BIOS setting on the machine in order to boot-up from created disk.
Turn the machine on, and then hold down DEL key on the operation panel.
If you couldn’t get BIOS screen and machine is normally start-up, turn the
machine off after ultrasound image is displayed and then, repeat the instruction
from step (3).
(4) When you get following screen, enter ep5608 and then press [ (ENTER)] key on the
full-keyboard.
(6) By operating arrow key on the full-keyboard, select ”1st Boot Device” and then press [
(ENTER)] key. Select connected USB drive (in the figure below, this is [USB:PIONEER
BD-RW]) from displayed list, then press [ (ENTER)] key.
(7) Make sure that ”1st Boot Device” is set to DVD drive on the screen.
Page 9 of 33
F37 Software Installation Procedure, Rev.0
(9) By operating arrow key on the full-keyboard, Select ”Save Changes and Exit” and then
press [ (ENTER)] key.
The message ”Save configuration changes and exit setup?” appears. Select [OK] and press [
(ENTER)] key.
(10) The machine is automatically rebooted and following message is displayed on the monitor. Then,
press [ (ENTER)] key immediately.
If the following message is displayed, press [ (ENTER)] key on the full-keyboard to continue.
Page 10 of 33
F37 Software Installation Procedure, Rev.0
If the machine doesn’t boot-up from installation disk and start-up normally, turn
the machine off after ultrasound image is displayed and then, repeat the
instruction from step (10).
(11) The following screen appears and the machine boot-up from installation disk.
(12) After two minutes passed, the following disk image burning tool “SIRBRE” is started from
installation disk. Put the check mark in the ”Shutdown system after install” box, and then
click on the [Install Disk Image] button.
(13) If the following window appears, click on the [OK] button to continue.
Page 11 of 33
F37 Software Installation Procedure, Rev.0
From this step, the displayed screen seems to stop, but DO NOT make any
operation until software installation is completed. While the HDD access LED on
the operation panel is lighting and blinking, the installation is in progress.
(14) After around 2 or 3 minutes, the following screen appears. During installation process, the
installation status can be confirmed with progress bar at the bottom of screen.
Although it depends on the reading speed of connected USB drive, this process may take up to
fifteen minutes.
(15) After completion of whole installation process, the machine automatically turns off. Remove the
USB portable drive from the machine.
If you couldn’t get BIOS screen and machine is normally start-up, turn the
machine off after ultrasound image is displayed and then, repeat the instruction
from step (17).
Reboot and Select proper Boot device
or Insert Boot Media in selected Boot device and press a key
(17) When you get following screen, enter ep5608 and then press [ (ENTER)] key on the
full-keyboard.
Page 12 of 33
F37 Software Installation Procedure, Rev.0
(19) By operating arrow key on the full-keyboard, Select ”Load Optimal Defaults” and then
press [ (ENTER)] key.
The message ” Load Optimal Defaults?” appears. Select [OK] and press [ (ENTER)] key.
(20) By operating arrow key on the full-keyboard, Select ”Save Changes and Exit” and then
press [ (ENTER)] key.
The message ”Save configuration changes and exit setup?” appears. Select [OK] and press [
(ENTER)] key.
Page 13 of 33
F37 Software Installation Procedure, Rev.0
(21) The usual ultrasound image screen is not displayed after the machine started. Instead, Windows
OS screen is displayed.
(23) After following screen appears, Trun the power swicth off from the operation panel.
Page 14 of 33
F37 Software Installation Procedure, Rev.0
SW
1 2
The machine booting-up in this time takes longer than usual. DO NOT turn the
machine off during a HDD access LED on the operation panel is lighting and
blinking.
When the message shown at right appears on
screen, the firmware update for PC boards
will take place. DO NOT turn the system off
until ultrasound image is displayed on the
monitor. This process may take up to three
minutes.
Page 15 of 33
F37 Software Installation Procedure, Rev.0
Page 16 of 33
F37 Software Installation Procedure, Rev.0
All data in the HDD will be erased by performing the software full installation. If there is user
data such as stored image, preset on the HDD, please take a data backup beforehand.
The status of option software (SOP) will be kept even if you perform the software full
installation.
Selecting boot-up device Select the boot-up device so that the machine is
booting-up from software installation disk.
Operation check After restart the machine manually, enter the S/N
information on the maintenance screen, then
restoring the user data if necessary. Perform the
overall operation check.
Page 17 of 33
F37 Software Installation Procedure, Rev.0
You can confirm the machine network configuration from “DICOM-Store, Send”
on the common preset menu.
You can confirm the machine log files from “LOG” on the maintenance screen.
Take a backup of these if necessary.
Printer property settings for digital B/W and color printer (UP-D897 and so on)
Page 18 of 33
F37 Software Installation Procedure, Rev.0
If you find any PC printer on the pull-down menu under the “Printer Property” on
the maintenance menu – OTHER, some software driver for PC printer was installed
on this machine.
If you find version information under the “McAfee Solidifier” on the maintenance
menu- SECURITY, the McAfee Embedded Control software was installed on this
machine.
OB Measurement setting
You can confirm the OB Measurement setting on SYSTEM1 screen from
maintenance menu.
Page 19 of 33
F37 Software Installation Procedure, Rev.0
Do not turn the machine off / Do not remove the USB device during accessing the hard
disk and/or the USB device.
When you connect some USB device into the machine, disconnect them before update
work.
(1) Follow the instruction below to set the machine to the maintenance mode.
Turn the machine off.
Remove the right side cover and main chassis cover, and then change the maintenance Dip SW
as below.
SW
1 2
Page 20 of 33
F37 Software Installation Procedure, Rev.0
(3) Insert the created software installation disk that is created at previous step in the connected USB
drive. Turn the machine on, and then hold down F11 key on the operation panel.
If you couldn’t get BIOS screen and machine is normally start-up, turn the
machine off after ultrasound image is displayed and then, repeat the instruction
from step (3).
(4) When you get following screen, enter ep5757 and then press [ (ENTER)] key on the
full-keyboard.
(5) The bootable device list appears. By operating arrow key on the full-keyboard, select connected
USB Blu-ray drive (in the figure below, this is [PIONEER BD-RW BDR-XD053.00]) from
displayed list, then press [ (ENTER)] key.
(6) The machine is automatically rebooted and following message is displayed on the monitor. Then,
press [ (ENTER)] key immediately.
If the machine doesn’t boot-up from installation disk and start-up normally, turn
the machine off after ultrasound image is displayed and then, repeat the
instruction from step (6).
Page 21 of 33
F37 Software Installation Procedure, Rev.0
(7) The following screen appears and the machine boot-up from installation disk.
(8) After two minutes passed, the following disk image burning tool “SIRBRE” is started from
installation disk. Put the check mark in the ”Shutdown system after install” box, and then
click on the [Install Disk Image] button.
(9) If the following window appears, click on the [OK] button to continue.
Page 22 of 33
F37 Software Installation Procedure, Rev.0
From this step, the displayed screen seems to stop, but DO NOT make any
operation until software installation is completed. While HDD access LED on the
operation panel is lighting and blinking, the installation is in progress.
(10) After around 2 or 3 minutes, the following screen appears. During installation process, the
installation status can be confirmed with progress bar at the bottom of screen.
Although it depends on the reading speed of connected USB Blu-ray drive, this process may take
up to fifteen minutes.
(11) After completion of whole installation process, the machine automatically turns off. Remove the
connect USB portable Blu-ray drive from the machine.
Page 23 of 33
F37 Software Installation Procedure, Rev.0
The machine booting-up just after software installation takes longer than usual DO
NOT turn the machine off during HDD access LED on the operation panel is lighting
and blinking.
(1) Turn the machine on. The following screens appear continually during the machine starting-up.
(2) The usual ultrasound image screen is not displayed after the machine started. Instead, Windows
OS screen is displayed as below.
By pressing “ID” key and “D” key on the operation panel keyboard somultaneously, Windows
desktop screen appears.
Page 24 of 33
F37 Software Installation Procedure, Rev.0
(3) Press “ID” key and “R” key on the operation panel keyboard somultaneously to open “Run”
window. Type control in the colum “Open:” and click on the [OK] button
(4) Click on the [System] icon on the displayed “All Control Panel Items” window.
(5) Click on the [View details in Windows Activation] under the “Windows Activation” on
the displayed window.
Page 25 of 33
F37 Software Installation Procedure, Rev.0
(6) Click on the [Activate] button on the displayed “Windows Activation” window.
(7) The activation process fails and following screen appears. Click on the [Close] button on it.
(8) The following window appears next. Click on the [Activate by phone] button to perform the
activation process by phone.
Page 26 of 33
F37 Software Installation Procedure, Rev.0
(9) The available phone number appears. Select nearest location from pull-down menu (in the
figure below, this is [Japan]), and then Click on the [Next] button.
(11) The following window appears after the activation process is completed. Click on the
[Close] button.
Page 27 of 33
F37 Software Installation Procedure, Rev.0
(12) Confirm that message “Windows is activated” is displayed on the Windows Activation
window, then click on the [OK] button.
(13) Click on the [x] button on each windows below to close them.
Page 28 of 33
F37 Software Installation Procedure, Rev.0
Page 29 of 33
F37 Software Installation Procedure, Rev.0
(3) The “Windows Script Host” window appears. Confirm that ”License Status” is shown
as ”Licensed”, and then click on the [OK] button.
(4) The message “Type (YES/NO) : “ appears on the “Windows Script Host” window. Type yes
and then press [ (ENTER)] key on the operation panel full-keyboard.
Page 30 of 33
F37 Software Installation Procedure, Rev.0
(5) After a few second passed, the window “Shut own Windows” appears. Click [OK] button on
it. The machine automatically turns the power off.
Page 31 of 33
F37 Software Installation Procedure, Rev.0
SW
1 2
The machine booting-up in this time takes longer than usual. DO NOT turn the
machine off during HDD access LED on the operation panel is lighting and
blinking.
If SOP-F37-69 (McAfee Embedded Control
software) was installed, the message shown at
right appears on screen, press [ENTER]
switch on the operation panel to continue the
booting-up process.
This message indicates that the PM-F37-S002
is not installed on the machine, you have to
re-install this at next step.
Page 32 of 33
F37 Software Installation Procedure, Rev.0
(End of Document)
Page 33 of 33