Académique Documents
Professionnel Documents
Culture Documents
95
37
266
30
15
265
ALTERNADORES - ALTERNATORS
LSA 35 - 35 E Monofásico/single phase
Instalación y mantenimiento / Installation and maintenance
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35, 35E - 2 Pole
Estimado Cliente, Dear Customer,
Este manual se utiliza para el alternador LE- As one of the world's leading alternator manu-
ROY-SOMER «PARTNER», que Usted acaba facturers
de adquirir. combining up to the minute technology in de-
Ultimo de una nueva generación de alternado- sign and manufacturing facilities
res, «PARTNER» se beneficia de la experien- with a high standard of quality control,
cia de uno de los más importantes constructo- we are pleased to introduce you
res mundiales, utilizando una tecnología de to our latest generation of alternators
vanguardia a nivel de automatización de los «PARTNER».
materiales seleccionados y de un control de
calidad riguroso. We ask you to carefully read and follow
the information given in this manual on instal-
Apreciamos su elección y deseamos atraer su lation and adjustment so as
atención en lo que respecta al contenido de to enable you to enjoy many years of care-free
este manual de mantenimiento. and dependable operation.
En efecto, el respeto de algunos puntos im-
portantes durante la instalación, el uso y el Yours
mantenimiento de su alternador le asegurará
un funcionamiento sin problemas durante lar-
gos años. «LEROY-SOMER» alternator.
LEROY-SOMER ALTERNADORES
SUMARIO INDEX
1. GENERALIDADES 1 - General
1 - Characteristics 3
1 - Características 2 - Normal operating conditions 3
2- Utilización en carga
2 - Wiring diagrams
2. ESQUEMAS DE PRINCIPIO
1 - Singlephase 4 wires 4
1 - Monofásico 4 hilos 2 - Singlephase 3 wires + 12/24 DC 4
2 - Monofásico 3 hilos con carga batería 3 - Characteristics of components 4
3 - Características de los componentes
3 - Disassembly and reassembly
1 - Assembly instructions 5
3. OPERACION DE MONTAJE Y DESMONTAJE
2 - Disassembly instructions 5
1 - Instrucciones de montaje 3 - Two bearing alternators 6
2 - Instrucciones de desmontaje Belt driven
3 - Alternador bipalier 4 - Storage location 6
Acoplamiento polea-correa 5 - Minimum tools required 6
4 - Almacenamiento - Situación
5 - Herramientas mecánicas y eléctricas minimas 4 - Starting up 6
4. PUESTA EN SERVICIO 5 - Fault finding 7
5. DIAGNOSIS DE AVERIAS
6 - Testing of components
6. COMO EFECTUAR LOS TESTS ELECTRICOS
1 - Measurement of resistance
1 - Medida de resistencias de los bobinados of the various coils 8
2 - Medidas de los diodos 2 - Checking the diodes 8
3 - Medida del condensador 3 - Checking the capacitor 8
2
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35, 35E - 2 Pole
1. GENERALIDADES 1 - GENERAL
1.1 - Characteristics
I-1 Características PARTNER LSA 35 Alternator, single-phase, self exciting,
Alternador PARTNER LSA 35 monofásico, autoexcitado, brushless. Excitation by capacitor without regulator
sin anillos ni escobillas, compound, excitación por (A.V.R.).
condensador, sin regulador.
Conforms to : CSA, NEMA, VDE, BSS, CEI.
Conforme a la normas : CSA, NEMA, VDE, BSS, CEI.
Cooling : internal fan, air entry non drive end.
Enfriamiento : Turbina interna, aspiración al lado
opuesto al acoplamiento. Protection : IP 23 M, class F/H
Protección : IP 23 M, clase F/H. Speed : 3000 or 3600 rpm depending on the frequency.
Velocidad : 3.000 a 3.600 rpm, según la frecuencia. Utili- Rotation : clock wise or anticlock wise. Below 40 % of
zación en ambos sentidos de rotación. Por debajo del 40 nominal speed, non voltage output.
% de la velocidad nominal, no hay tensión.
1.2 - Normal operation conditions
I-2 Utilizacion en carga Continuous duty : S1 - unity PF load and for ambiant
temperature ≤ 40° C and altitude ≤ 1000 m, your alterna-
En uso contínuo : S1, sobre carga resistiva para tempe- tor winding is designed for a life of 20.000 hours.
ratura ≤ 40 grados C y altitud ≤ 1.000 m, el alternador
está garantizado para una duración de vida del orden de As an emergency supply : S2 - over load + for 1 hour -
20.000 horas de bobinado. life of winding = 10 000 hours.
En uso de emergencia : S2, sobre carga + 10 % durante 1 Maximum service : S6 maximum intermittent duty ie.
hora. Duración de vida de 10.000 horas del bobinado. 20 % of S1 rating in line with engine curves. Life of win-
ding 3000 hours.
En uso máximo : S6, sobre carga ocasional + 20 % du-
rante algunos minutos (arranque de motores). Duración Voltage : single phase 4 wires reconnectable for high or
de vida del bobinado 3.000 horas. low voltage.
Tensión 110 ó 120 V Options : single phase non reconnectable 3 wires sys
baja tem low voltage, with supplementary 12 V and 24 V DC
Optión monofásica : 3 hilos no reconectables en tensión output through a rectifier bridge for battery charging.
baja, con salidas de hilos suplementarios 12 V y 24 V
cableadas desde el puente rectificador para carga de
batería cuya intensidad de carga corresponde a la in-
tensidad nominal del alternador.
TYPE IA battery charge
LSA 35 -M 5 13
TIPO IA carga de batería
LSA 35 - M 7 16
LSA 35 - M 8 19
LSA 35 - M 5 13 LSA 35 - L 6 23
LSA 35 - M 7 16 LSA 35 - L 9 27
LSA 35 - M8 19 (data equal for LSA 35 E)
LSA 35 - L 6 23
LSA 35 - L 9 27
ENERGY SUPPLY
DISTRIBUTION D'ENERGIE Single phase or three phase sockets are limited to 16 A
Les prises monophasées ou triphasées sont limitées à max.
16 Ampères maximum. For the larger current the supply + protection should be
Pour un courant plus important, la distribution sera réali- external.
sée et protégée à l'extérieur de la machine.
3
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35, 35E - 2 Pole
1. ESQUEMAS DE PRINCIPIO 2 - WIRING DIAGRAMS
2.1 - Single phase 4 wires
1.1 Monofásico 4 hilos
Z1 - White
U1 U2 U5 U6 Z2 - Brown
U1 U5 U2 U6
T1 T2 T3 T4
Main windings
Verde Rojo Negro Yellow T1 T3 T2 T4
220/240 V Green Red Black
Amarillo
Principales
bobinades
L1 L2 U2 U1 U5 U6 L1 110/120 V L2
T2 T1 T3 T4
1.2 Monofásico 3 hilos con carga 2.2 Single phase 3 wires + 12/24 V - DC
Blanco
batería T8 - White
Diodo
ESTATOR
ROTOR Diode STATOR
D C Fase auxiliar
Auxiliary phase
T5 -- Brown - Marrón
0 +24
+12
4
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35, 35E - 2 Pole
3 - OPERACION DE MONTAJE Y DES-
MONTAJE
DISASSEMBLY - REASSEMBLY
Fig. 4
Unscrwew the 4 fixing bolts of the stator frame to the
flange mounted on the engine. (Fig.4)
5
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35, 35 E - 2 Pole
3.3 - Alternador bipalier 3.3 - Two bearing alternator
Acoplamiento polea-correa : la bancada utilizada para Belt driven : Slide rails used for belt adjustment should
tensar las correas tiene que colocarse antes de montar be accurately positioned before mounting the alternator.
el alternador.
Adjustment bolts should be placed in contact only with
Los tornillos de tensado deben ser aplicados única-
metal surfaces of alternator and judiciously distributed.
mente sobre las partes metálicas y lógicamente dis-
puestas. Maximum radial force : 85 kg for a bearing life 10 000
Esfuerzo radial máximo : recomendado 85 kg para una hours.
duración de vida del rodamiento delantero de 10.000 h. - Bearing used :
– Rodamientos unilizados : - N.D.E. 6206 - C 3 H.T. 140
– Delantero : AV 6206 - C 3 protegido H.T. 140 - D.E. 6205 - C 3 H.T. 140
– Trasero : AR 6205 - C 3 protegido H.T. 140 - Diam. shaft : Ø 28 mm
– Diámetro del eje : 28 mm - Length shaft : 60 mm
– Longitud del eje : 60 mm For belt and pulley sizes, the manufacturer's recomman-
Se aconseja seguir estrictamente las recomendaciones dations should be followed.
del fabricante para las dimensiones de las correas y poleas.
3.4 - Storage location
3.4 - Almacenamiento - Situación Location : hot air from the alternator or engine exhaust
Almacenamiento : Evitar almacenar el alternador en lu- must be prevented from recycling to cooling air inlet.
gar húmedo, polvoriento o sometido a la intemperie. Storage : storing the alternator in damp or dirty areas
Emplazamiento : Es necesario impedir, en la medida de should at all time be avoided.
lo posible, el reciclaje de aire caliente, teniendo cuidado
con los gases de escape.
HOT AIR
AIRE CALENTADO
3.5 - Minimum tools required OUTLET
3.5 - Herramienta mecánica y eléctrica - Spanner Ø 9/16"
minimas - Spanner Ø 13 mm
– Llave de tubo diámetro 9/16" - Multimeter for control test
– Llave de tubo 13 mm - ALLEN key for screws FHc m8
– Polímetro para control
– Llave para tornillo FHc diámetro m8
4 - STARTING UP
4 - PUESTA EN SERVICIO Initial operation :
All alternators are tested in a Leroy-Somer factory and
Primera puesta en servicio :
the speed of the engine is adjusted to 3120 rpm for
Todos los alternadores LEROY-SOMER son comproba-
52 Hz and 3720 rpm for 62 Hz. At these nominal no load
dos sobre bancos de pruebas en fábrica. En cuanto el
speeds the nominal voltage is obtained, in case of diffe-
régimen nominal del motor es alcanzado (3120 rpm 52
rent values being obtained on first operation, check engi-
Hz) la tensión está presente.
ne speed with a rev.counter or Hz.meter.
En caso de valor erróneo, regular la velocidad del motor
con un cuenta-vueltas o con un frecuenciómetro.
Placa de características : Ejemplo Name plate : Example
Servicio Potencia Tensión Intensidad Duty Power Voltage Amps
PARTNER PARTNER
Continuo 3,0 110/220 V 27.3/13.6 A Continuous 3,6 120/240 V 30/15 A
ALTERNADOR ALTERNATEUR
Emergencia 3,3 110/220 V 30/15 A ST. BY 4,0 120/240 V 30.3/15.6 A
DIN 70020 3,6 110/220 V 32.7/16.4 A DIN 70020 4,5 120/240 V 37.5/18.7 A
LSA 35 M 5 LSA 35 M 5
cos. phi = 1,0 12/2 A CC / A P.F. = 1.0 12/24 DC / A
monofásico monophasé
3000/min -1 50 Hz IP 23 M 3600/RPM 60 Hz IP 23 M
6
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35, 35E - 2 Pole
5 - DIAGNOSIS DE AVERIAS
1 - SIN CARGA
Défaut enregistré Cause initiale du défaut Opération à réaliser
Ausencia de tensión Pérdida del flujo remanente Conectar una batería de 4,5 V en las bornas del conden-
en el arranque sador.
Poner en carga el alternador y hacerlo girar un poco + rá-
pido un instante.
Condensador defectuoso Cambiar el condensador (§ VI-3)
Diodo rótor fuera de circuito o Cambiar los 2 diodos del rótor
en cortocircuito (§ VI-2)
Cortocircuito del bobinado o Verificar las resistencias de
conexiones aflojadas los bobinados (§ II-3)
Volver a elevar el motor térmico
Tensión en vacío inferior al 80 % Velocidad del motor térmico a 3120 rpm en vacío
de tensión nominal demasiado baja (frecuencia alternador 52 Hz)
1 diodo del rótor fuera de servicio o en corto- Cambiar los diodos del rótor (§ VI-2)
circuito Verificar las resistencias de
Cortocircuito parcial del bobinado los bobinados (§ II-3)
Tensión demasiado Velocidad del motor térmico Ajustar la velocidad del motor
alta en vacio demasiado alta térmico a 3120 rpm
2 - CON CARGA
1 diodo del rótor fuera de servicio Cambiar los 2 diodos del rótor
o en cortocircuito (§ VI-2.1)
Tensión válidaen vacío y demasia- El motor térmico se viene abajo Quitar carga al alternador ; la carga
do baja en carga en velocidad aplicada es demasiado elevada
El motor térmico está mal regulado :
dirigirse al especialista del motor
Calentamiento excesivo Orifícios de ventilación parcialmente Desmontar y limpiar el estátor
taponados
Rotor diode out of order or short circuit Change the 2 diodes on the rotor (§ 6-3)
Winding short circuit or loose connections Check the resistance of coils (as table) (§ 2-3)
Voltage with no load less than Speed of engine too low Set speed of engine to 3120 rpm or 3720 rpm with no load
80 % of nominal voltage (frequency alternator 52 Hz or 62 Hz).
1 rotor diode out of order or short circuit Change the 2 diodes on the rotor (§ 6-2) short circuit
Partiel short circuit in winding Check the resistance of the coils (as table). (§ 2-3)
Too high voltage without load Speed of engine too high Adjust the speed to 3120 rpm or 3720 rpm ( 52 Hz or 62
Hz)
2 - With load
Correct voltage 1 rotor diode short circuit or out of order Change the 2 diodes on the rotor (§ 6-2.1)
with load, low voltage with load
Excessive heat (over heating) Ventilator holes partially blocked Dismantle and clean the stator
7
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35, 35E - 2 Pole
6 - COMO EFECTUAR LOS 6 - TESTING OF COMPONENTS
TESTS ELÉCTRICOS CONDENSATEUR
6.1 - Medida de resistencias CAPACITOR 6.1 - Measurement of resistance
de los bobinados of the various coils
Estátor : Stator :
– desatornillar los 4 tornillos de - unscrew the top plastic cover.
fijación de la tapa plástica su- - disconnect the capacitor wires in order
perior, to check the resistance of the auxiliary
– desconectar los hilos del phase (p. 5).
condensador para leer la resis- - disconnect the capacitor 4 wires of the
tencia de la fase auxiliar (p. 5)., connector in order to check the resistan-
– desconectar los hilos del ce at the main winding (p. 5).
conector para leer la resisten-
cia de la fase principal (p. 5).
Rótor :
– proceder al desmontaje del Rotor :
estátor (p. 6). - unscrew the 4 fixing screws of the sta-
tor frame to the flange mounted on the
Desoldar los hilos de los diodos engine.
para leer la resistencia de cada - remove the complete frame (see p. 6).
bobinado (p. 5). - unsolder the wires from the diodes in
order to check the resistance of each
winding (p. 5).
A
INTERRUPTEUR
SWITCH
Capacitor
Alternadores Condensateur 220/50 Hz 240/60 HZ
Alternator MF IA IA
LSA 35 M 5 30 2,1 2,7
LSA 35 M 7 40 2,8 3,6
LSA 35 M 8 50 3,5 4,5
LSA 35 L 6 60 4,1 5,4
LSA 35 L 9 70 4,8 6,3
8
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35, 35E - 2 Pole
7 - REPUESTOS 7 - SPARE PARTS
A QUIEN DIRIGIRSE
Address enquiries and orders to :
A su proveedor habitual ó a :
MOTEURS LEROY-SOMER
Usine de Sillac
MOTEURS LEROY-SOMER
16015 ANGOULÊME CEDEX FRANCE
Usine de Sillac
Tel : (33) 45.64.45.64 -
16015 ANGOULEME CEDEX FRANCE Service : SAT 45.64.43.66 ou 45.64.43.68 -
Tel : (33) 45.64.45.64 - Fax : 45.64.43.24
Service : SAT 45.64.43.66 ou 45.64.43.68 -
Fax : 45.64.43.24
To ovoid errors on delivery of spare parts, all information
Para evitar errores en la entrega de los repuestos, no ol- marked on nameplates shall be furnished on parts or-
vidarse de indicar las informaciones anotadas en la pla- ders, in particular model and serial number of the alter-
ca descriptiva, sobre todo el tipo y número de la má- nator. Also give the parts numbers from the parts lists.
quina y también el número de referencia de la pieza en
la nomenclatura.
When single bearing, indicate :
Para los alternadores monopalier precisar : - Flange : SAE Nr (bore diameter, number and diameter
Brida : número de SAE de la brida (el Ø de centrado, of holes).
el número el Ø de los agujeros). - Disc : disc Nr or outside diameter.
9
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35 - 2 Pole
LSA 35 DESPIECE MONOPALIER
SINGLE BEARING
48 214
70 13
183
184 51
188
1 49
4
200
37
266
30
15
265
166
124
36
349
354
109
110
55
56
50
37
266
30
15
22
410
63
60
166
124
36
349
354
109
110
55
56
50
412
284
61
62
10
Alternadores Alternator
LSA 35, 35E - 2 Polos LSA 35E - 2 Pole
LSA 35. E DESPIECE MONOPALIER
SINGLE BEARING
183
36
13
349
70
354
109
110
1
4
37
266
30
15
265
200
166
49
51
214
200
166
49
51
214
412
284
61
62
11
MOTEURS LEROY-SOMER 16015 ANGOULEME CEDEX-FRANCE