Académique Documents
Professionnel Documents
Culture Documents
Switch (Normally Open): A switch that will close at a specified point (temp, press, etc.). The
circle indicates that the component has screw terminals and a wire can be disconnected from it.
Switch (Normally Closed): A switch that will open at a specified point (temp, press, etc.).
No circle indicates that the wire cannot be disconnected from the component.
Ground (Wired): This indicates that the component is connected to a grounded wire. The
grounded wire is fastened to the machine.
Ground (Case): This indicates that the component does not have a wire connected to ground.
It is grounded by being fastened to the machine.
Reed Switch: A switch whose contacts are controlled by a magnet. A magnet closes the
contacts of a normally open reed switch; it opens the contacts of a normally closed reed switch.
920, 930, 930T and 930T Series II Sender: A component that is used with a temperature or pressure gauge. The sender
Wheel Loaders
measures the temperature or pressure. Its resistance changes to give an indication to
T
the gauge of the temperature or pressure.
Electrical System
Relay (Magnetic Switch): A relay is an electrical component that is activated by electricity.
It has a coil that makes an electromagnet when current flows through it. The
electromagnet can open or close the switch part of the relay.
920: 930: Solenoid: A solenoid is an electrical component that is activated by electricity. It has a
coil that makes an electromagnet when current flows through it. The electromagnet
62K1-UP 41K1-UP can open or close a valve or move a piece of metal that can do work.
75J1-UP 73U1-UP Magnetic Latch Solenoid: A magnetic latch solenoid is an electrical component that is
activated by electricity and held latched by a permanent magnet. It has two coils (latch and unlatch)
that make electromagnet when current flows through them. It also has an internal switch that places
the latch coil circuit open at the time the coil latches.
STOP LAMP
PRESSURE SWITCH TO POWER SUPPLY O O O INDICATOR LAMP (RH)
FLASHER UNIT
DK BL
TURN SIGNAL and
BRAKE INDICATOR GY/B HAZARD WARNING SWITCH LT O B
PARKING BRAKE AIR PRESSURE LOW AIR
SWITCH
INDICATOR SWITCH PRESSURE SWITCH TO POWER SUPPLY W B
BUZZER O
F O O B/W GY/B F
T
LAMP (LH)
DISCONNECT SWITCH 1
BR PU STOP TAIL TURN T/W T/W
W/O
W/O
T/W
BR SWITCH BATTERY 12 VOLT HOUR
GY/B
PU O
METER
O/B
ATTACHMENT:
AIR CONDITIONER ATTACHMENT: Y
O FUSE HOLDER
PU GY
O ST
BR
TEST CIRCUIT M HEAT START
B HT W/O
O/B FRONT:
TURN SIGNAL (RH)
PRESSURE SWITCH SWITCH PU
W R R AMP
60 A R METER O ATTACHMENT:
STARTING
PU W W/O TURN SIGNAL (LH)
TO POWER SUPPLY
MOTOR
BR O
GLOW PLUGS O
ATTACHMENT - TURN SIGNAL
E E
R R
G DK GR W DK BL
10 AMP
GY B
ALT R STOP LAMP
PRESSURE SWITCH PU W DASH LAMPS DK BL
DK GR
BRAKE LAMP
INDICATOR 3.5 AMP B
REAR FLOOD LAMP T O W R B
LT GR
DK BL TO POWER SUPPLY W W
O O O WIPER SWITCH WIPER MOTOR
FRONT FLOOD LAMP W
B
PU O DK GR O O O
W
ATTACHMENT: 15 AMP
GY GY LIGHT SWITCH
STOP - TAIL BR BR BR SUPPLEMENTAL STEERING CAB:
LAMP (LH) INDICATOR LAMP FLOOD LAMPS
D T T O
D
FD
LIGHT HT TO SPARE
O O SWITCH B 15 A FUSE HOLDER
R
O O BR ATTACHMENT:
10 AMP TURN SIGNAL (RH)
Y O O
Y T
15 AMP
ATTACHMENT (CAB) - WIPER, HEATER and FLOOD LAMPS
F PU Y Y
Y 15 AMP
W W DK BL DK BL
DK GR
DK GR
15 AMP
W/O
O/B
Y Y R R ENGINE OIL
FUSE BLOCK PRESSURE SWITCH
T T R R ELECTRIC CLUTCH
(Dimensions: 39 inches x 28 inches)
B/W
PU
START SWITCH
Y Y O GY
ATTACHMENT:
STOP - TURN - TAIL
GY GY AIR CONDITIONER
KENR9550
C O B/W R UNIT C
BR BR BR A
20 AMP
RELAY
E
BACKUP ALARM
SWITCH C
BACKUP ALARM B/GY
ATTACHMENT:
TURN SIGNAL
ATTACHMENT - AIR CONDITIONER
T/W
ATTACHMENT:
W/O TURN SIGNAL
SWITCH STEERING INDICATOR LAMP
GY
B R/Y LT-BL/BR O TO LIGHT SWITCH
30 Page,
TERMINAL “B”
LT-BL/BR
O/B
D
B FLOW INDICATOR SWITCH B
BR
DK GR
TO BRAKE LAMP
INDICATOR
W/O
O/B
DK GR ATTACHMENT - SUPPLEMENTAL STEERING
(INDICATOR LAMP)
WIRE COLORS
(R) RED
(O) ORANGE
SCAVENGE PUMP
(DK BL) DARK BLUE
SYMBOL DESCRIPTION
(PU) PURPLE
CIRCUIT CONNECTED (DK GR) DARK GREEN
(B) BLACK
CIRCUIT NOT CONNECTED
(W/O) WHITE / ORANGE
ELECTRICAL CONNECTION TO (T/W) TAN / WHITE
MACHINE STRUCTURE
(B/W) BLACK WHITE
INTERNAL ELECTRICAL CONNECTION
TO SURFACE OF COMPONENT (W) WHITE
(Y) YELLOW
CONNECTOR
(T) TAN
A
Connector Pins H# CIRCUIT GROUPING DESIGNATION
Y T
R R O O W/O T/W Y DK BL THIS ELECTRICAL SCHEMATIC IS FOR THE:
PU W 920, 930, 930T and 930T SERIES II WHEEL LOADERS
W/O MEDIA NUMBER: KENR9550
DK BL GY O/B
Components are shown installed on a fully operable machine.
8 7 6 5 4 3 2 1