Académique Documents
Professionnel Documents
Culture Documents
Tables of Dimensions
Please note that these tables list dimensions, not available thread dies in stock.
Rolled threads
2 © Eichenberger Gewinde AG – V 16 02 20
Important notes for premachining
b
a
following pages for dimensions a and b. The
shaded green areas identify the four different
tolerances for these dimensions. Conforming threads Dimension b [mm]: Chamfer, intake or pass
d diameter (theoretical root diameter); without
0 prescribed tolerance.
Tolerance Green 1
– 0.03 mm c Value in table = maximum dimension.
0
Tolerance Green 2
b
b
a
– 0.05 mm Dimension c: Chamfer or intake angle
0 · 20° to 1000 N/mm2
Tolerance Green 3
– 0.08 mm
· approx. 15° over 1000 N/mm2
0
Tolerance Green 4 Non-conforming threads
– 0.12 mm
e Dimension d [mm]: Pass width
If no special tolerances are required, please · at least 1.5 x pitch
refer to tables for pre-machining and cham- c
fer diameters and assign proper tolerance Dimension e [mm]: Thread runout
b
a
(color-coded). · approx. 1.5 x pitch
Standard threads are shown in the black (shorter runouts on request).
areas of the metric thread table.
Caution: If parts are scheduled for additional Effects of non-compliance with premachining • Rolling diameter is below prescribed
surface or heat treatment after rolling, this may measurements: tolerance
have to be taken into consideration when If the rolling diameter is below the required
premachining the workpiece. • Rolling diameter exceeds prescribed tolerance, the flank diameter may be rolled
tolerance true to tolerance but the outer diameter crest
Experience has shown that threads produced When the die is filled with the engaged ma- may be below the required tolerance.
in continuous operation, i.e. longer than ap- terial of the blank during rolling (see cutout
prox. 120 mm, must be below listed values Fig. 1), the flank diameter cannot be further • Chamfering
prior to rolling. Please take advantage of our influenced in the minus range (not even by Since the workpiece material exerts axial
experience and inquire about the appropriate further feeding the rolling dies). The result is flow properties in the areas of thread intake
premachining diameter. that the flank diameter becomes too big, the or runout, there is enough room to prevent
tolerance gauge will jam and the counterpart any damage to the rolling die if chamfering
If new profiles are required, especially narrow will not fit on the thread. has been done properly (Fig. 1). In the event
tolerances or extreme pitches, tests will be A massive oversize of the blank may en- of non-compliance with prescribed intake
conducted to obtain premachining diameter. danger the rolling die and often causes the angle (chamfering), the material with axial
workpiece to burst thus breaking the die. flow will inevitably strain the dies to the
Therefore it is very important to premachine breaking point (Fig. 2).
all parts of the same series with prescribed
tolerances.
Rolling die Rolling die
Fig. 1: Fig. 2:
correct incorrect
chamfering chamfering
Rolled threads
© Eichenberger Gewinde AG – V 16 02 20 3
Metric threads Metric threads
p 0,25 0,35 0,4 0,45 0,5 0,6 0,7 0,75 0,8 1,0 1,25 1,5 1,75 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 8,0 p
Ø a b a b a b a b a b a b a b a b a b a b a b a b a b a b a b a b a b a b a b a b a b a b a b Ø
2 1,83 1,65 1,75 1,45 1,72 1,35 2
2,5 2,33 2,15 2,25 1,95 2,18 1,80 2,5
3 2,83 2,65 2,75 2,45 2,64 2,25 3
3,5 3,33 3,15 3,25 2,95 3,14 2,75 3,08 2,60 3,5
4 3,83 3,65 3,75 3,45 3,64 3,25 3,51 2,95 4
4,5 4,33 4,15 4,25 3,95 4,14 3,75 3,98 3,40 4,5
5 4,83 4,65 4,75 4,45 4,64 4,25 4,48 3,90 4,44 3,80 5
6 5,83 5,65 5,75 5,45 5,64 5,25 5,48 4,90 5,31 4,55 6
7 6,83 6,65 6,75 6,45 6,64 6,25 6,48 5,90 6,31 5,55 7
8 7,83 7,65 7,75 7,45 7,64 7,25 7,48 6,90 7,31 6,55 7,15 6,20 8
9 8,83 8,65 8,75 8,45 8,64 8,25 8,48 7,90 8,31 7,55 8,15 7,20 9
10 9,83 9,65 9,75 9,45 9,64 9,25 9,48 8,90 9,31 8,55 9,15 8,20 8,98 7,85 10
11 10,75 10,45 10,64 10,25 10,48 9,90 10,31 9,55 9,98 8,85 11
12 11,75 11,45 11,64 11,25 11,48 10,90 11,31 10,55 11,15 10,20 10,98 9,85 10,81 9,50 12
14 13,75 13,45 13,64 13,25 13,48 12,90 13,31 12,55 12,98 11,85 12,65 11,20 14
15 14,75 14,45 14,64 14,25 14,48 13,90 14,31 13,55 13,98 12,85 15
16 15,75 15,45 15,64 15,25 15,48 14,90 15,31 14,55 14,98 13,85 14,65 13,20 16
17 16,75 16,45 16,64 16,25 16,48 15,90 16,31 15,55 15,98 14,85 15,65 14,20 17
18 17,75 17,45 17,64 17,25 17,48 16,90 17,31 16,55 16,98 15,85 16,65 15,20 16,32 14,50 18
20 19,75 19,45 19,64 19,25 19,48 18,90 19,31 18,55 18,98 17,85 18,65 17,20 18,32 16,50 20
22 21,75 21,45 21,64 21,25 21,48 20,90 21,31 20,55 20,98 19,85 20,65 19,20 20,32 18,50 22
24 23,75 23,45 23,64 23,25 23,48 22,90 23,31 22,55 22,98 21,85 22,65 21,20 21,98 19,80 24
25 24,75 24,45 24,64 24,25 24,48 23,90 24,31 23,55 23,98 22,85 23,65 22,20 25
26 25,75 25,45 25,64 25,25 25,48 24,90 25,31 24,55 24,98 23,85 24,65 23,20 26
27 26,75 26,45 26,64 26,25 26,48 25,90 26,31 25,55 25,98 24,85 25,65 24,20 24,98 22,80 27
28 27,75 27,45 27,64 27,25 27,48 26,90 27,31 26,55 26,98 25,85 26,65 25,20 25,98 23,80 28
30 29,75 29,45 29,64 29,25 29,48 28,90 29,31 28,55 28,98 27,85 28,65 27,20 27,98 25,80 27,65 25,10 30
32 31,75 31,45 31,64 31,25 31,48 30,90 31,31 30,55 30,98 29,85 30,65 29,20 29,98 27,80 32
33 32,75 32,45 32,64 32,25 32,48 31,90 32,31 31,55 31,98 30,85 31,65 30,20 30,98 28,80 30,65 28,10 33
34 33,75 33,45 33,64 33,25 33,48 32,90 33,31 32,55 32,98 31,85 32,65 31,20 31,98 29,80 34
35 34,75 34,45 34,64 34,25 34,48 33,90 34,31 33,55 33,98 32,85 33,65 32,20 32,98 30,80 35
36 35,75 35,45 35,64 35,25 35,48 34,90 35,31 34,55 34,98 33,85 34,65 33,20 33,98 31,80 33,32 30,50 36
38 37,75 37,45 37,64 37,25 37,48 36,90 37,31 36,55 36,98 35,85 36,65 35,20 35,98 33,80 38
39 38,75 38,45 38,64 38,25 38,48 37,90 38,31 37,55 37,98 36,85 37,65 36,20 36,98 34,80 36,32 33,50 39
40 39,75 39,45 39,64 39,25 39,48 38,90 39,31 38,55 38,98 37,85 38,65 37,20 37,98 35,80 37,32 34,50 40
42 41,75 41,45 41,64 41,25 41,48 40,90 41,31 40,55 40,98 39,85 40,65 39,20 39,98 37,80 39,32 36,50 38,98 35,80 42
45 44,75 44,45 44,64 44,25 44,48 43,90 44,31 43,55 43,98 42,85 43,65 42,20 42,98 40,80 42,32 39,50 41,98 38,80 45
48 47,75 47,45 47,64 47,25 47,48 46,90 47,31 46,55 46,98 45,85 46,65 45,20 45,98 43,80 45,32 42,50 44,65 41,10 48
50 49,75 49,45 49,64 49,25 49,48 48,90 49,31 48,55 48,98 47,85 48,65 47,20 47,98 45,80 47,32 44,50 50
52 51,48 50,90 51,31 50,55 50,98 49,85 50,65 49,20 49,98 47,80 49,32 46,50 48,65 45,10 52
55 54,48 53,90 54,31 53,55 53,98 52,85 53,65 52,20 52,98 50,80 52,32 49,50 55
56 55,48 54,90 55,31 54,55 54,98 53,85 54,65 53,20 53,98 51,80 53,32 50,50 52,32 48,40 56
58 57,48 56,90 57,31 56,55 56,98 55,85 56,65 55,20 55,98 53,80 55,32 52,50 58
60 59,48 58,90 59,31 58,55 58,98 57,85 58,65 57,20 57,98 55,80 57,32 54,50 56,32 52,40 60
62 61,48 60,90 61,31 60,55 60,98 59,85 60,65 59,20 59,98 57,80 59,32 56,50 62
64 63,48 62,90 63,31 62,55 62,98 61,85 62,65 61,20 61,98 59,80 61,32 58,50 59,98 55,70 64
65 64,48 63,90 64,31 63,55 63,98 62,85 63,65 62,20 62,98 60,80 62,32 59,50 65
68 67,48 66,90 67,31 66,55 66,98 65,85 66,65 65,20 65,98 63,80 65,32 62,50 63,98 59,70 68
70 69,48 68,90 69,31 68,55 68,98 67,85 68,65 67,20 67,98 65,80 67,32 64,50 65,98 61,70 70
72 71,48 70,90 71,31 70,55 70,98 69,85 70,65 69,20 69,98 67,80 69,32 66,50 67,98 63,70 72
75 74,48 73,90 74,31 73,55 73,98 72,85 73,65 72,20 72,98 70,80 72,32 69,50 75
76 75,48 74,90 75,31 74,55 74,98 73,85 74,65 73,20 73,98 71,80 73,32 70,50 71,98 67,70 76
80 79,48 78,90 79,31 78,55 78,98 77,85 78,65 77,20 77,98 75,80 77,32 74,50 75,98 71,70 80
82 Tolerance 0/– 0,03 80,65 79,20 79,98 77,80 79,32 76,50 82
85 83,65 82,20 82,98 80,80 82,32 79,50 80,98 76,70 85
90 88,65 87,20 87,98 85,80 87,32 84,50 85,98 81,70 90
95 Basic metric profile DIN 13 93,65 92,20 92,98 90,80 92,32 89,50 90,98 86,70 95
100 Applies to standard and fine threads 98,65 97,20 97,98 95,80 97,32 94,50 95,98 91,70 100
105 103,65 102,20 102,98 100,80 102,32 99,50 100,98 96,70 105
110 108,65 107,20 107,98 105,80 107,32 104,50 105,98 101,70 110
115 113,65 112,20 112,98 110,80 112,32 109,50 110,98 106,70 115
120 p = pitch [mm] 118,65 117,20 117,98 115,80 117,32 114,50 115,98 111,70 120
125 h3 = 0.61343 · p 123,65 122,20 122,98 120,80 122,32 119,50 120,98 116,70 125
130 128,65 127,20 127,98 125,80 127,32 124,50 125,98 121,70 124,60 119,80 130
R = 0.14434 · p
135 133,65 132,20 132,98 130,80 132,32 129,50 130,98 126,70 135
140 138,65 137,20 137,98 135,80 137,32 134,50 135,98 131,70 134,60 129,80 140
145 The metric threads we roll correspond to a tolerance of 6g. 143,65 142,20 142,98 140,80 142,32 139,50 140,98 136,70 145
150 148,65 147,20 147,98 145,80 147,32 144,50 145,98 141,70 144,60 139,80 150
155 Tolerance 0/– 0,05 152,98 150,80 152,32 149,50 150,98 146,70 155
160 157,98 155,80 157,32 154,50 155,98 151,70 154,60 149,80 160
Tolerance 0/– 0,08 Tolerance 0/– 0,12
p = pitch [mm]
h3 = 0.61343 · p
R = 0.14434 · p
UN threads
6 © Eichenberger Gewinde AG – V 16 02 20
Whitworth / Whitworth pipe threads (55°)
W = Whitworth thread
BSF = Whitworth fine thread
R = Whitworth pipe thread (gas pipe threads)
Whitworth threads
© Eichenberger Gewinde AG – V 16 02 20 7
The examples below illustrate the range of
available cold-rolling applications. We may
even inspire you to investigate innovative so-
lutions. Indeed, we are convinced that rational
cold-rolling solutions are available to solve
your particular threading problem. Why not
consider the benefits of cold rolling and profit
from our know-how?
6 x diameter specifications
· synthetic or brass The contents of this publication is
Milled edges as per Worm-gear profiles sion is granted. Every care has
cal developments.