Académique Documents
Professionnel Documents
Culture Documents
INSTR,INSTL,DXR-702A - LINEAR P/N: 220464 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 1 OF 2
DXR-702
PRODUCT DESCRIPTION
The DXR-702 is a two-channel digital receiver with two isolated Receiver channel two is a special channel. If channel two
relay outputs designed for use with Linear’s DX Format memory is empty, with no transmitters programmed into it, it
transmitters. This receiver can be used in a variety of remote will report low battery signals from any channel one transmitters
control applications. When the receiver detects a signal from capable of sending them. When a low battery transmission is
a transmitter programmed into its memory, the appropriate received, the channel two relay will latch, regardless of how
BY relay output activates. The relays have four optional output the option jumpers are set. The relay will remain engaged until
TWO- configurations. When the relays are set to latch, the receiver
outputs will follow the open/close door status sent from DXT-31
the channel two program button is pressed. The low transmitter
batteries should be replaced before resetting the relay.
CHANNEL door/window transmitters.
In a typical installation, the receiver is connected to an alarm
The unit can be powered from a 11-17 VDC or 12-16 VAC power
source. The relays’ normally open and normally closed contacts
DIGITAL control panel, door strike, camera, high current relay or some
other devices. Transmitters are used to activate or control the
can switch up to 1 amp at 24 volts AC/DC.
Cutting jumpers select how the relays activate. Four settings
RECEIVER devices. The receiver should be mounted with the supplied
mounting bracket indoors or inside a weather resistant
are possible. Both relays will function with the same option. The
factory setting causes the relays to engage for four seconds
non-metallic housing. each activation. Optionally, the relays can be set to engage for
The digital DX code format features over a million possible one second, toggle on with one activation then off with the next,
Installation codes. The DX transmitters are precoded at the factory to or latch engaged for door status or until reset by pressing the
unique codes, so no field coding is required. For versatility, program button.
Instructions any transmitter can be programmed into any receiver channel. A nine-inch wire whip antenna screws into the receiver’s antenna
Receivers must be programmed to the transmitter’s code before connector. Optionally, a remote antenna (Linear EXA-1000) can
system testing and operation. Up to 32 transmitters maximum be connected to the receiver for greater radio range. The red
can be programmed into the receiver. The transmitters can program indicator lights during RF reception. The installer can
be split in any number between the two receiver channels. verify that signals are being sent from transmitters and diagnose
interference problems by viewing the indicator. The indicator also
(760) 438-7000 • FAX (760) 438-7043 lights during memory programming/erasing and flashes to count
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340 the number of transmitters in memory.
www.linearcorp.com
ANTENNA NOTE:
CONNECTOR IF RELAY OPTION IS GOING TO TERMINALS
BE CHANGED: REMOVE POWER,
8 CUT JUMPERS, APPLY POWER,
CHANNEL 2 7 ERASE MEMORY, THEN RE- JUMPER
6 CHANNEL 2 PROGRAM ALL TRANSMITTERS
PROGRAM 5 WJ1
4 RELAY
BUTTON 3
2 NORMALLY OPEN CASE
1 CLOSED WITH SMALL
SCREWDRIVER JUMPER
ANTENNA WJ2
COMMON
NORMALLY
OPEN
RECEIVER CIRCUIT BOARD
BASEMENT BASEMENT - OR -
USE REMOTE
RIGHT WRONG! SNAP RECEIVER
ONTO BRACKET
ANTENNA
MOUNT RECEIVER OR ANTENNA AS LOCATING A RECEIVER OR ANTENNA
HIGH ABOVE EARTH LEVEL AS POSSIBLE BELOW EARTH LEVEL WILL IMPAIR RANGE
CORNER HOLE IS
SHARED FOR
UP TO 25 FEET
BRACKET CAN OF RG-59 CABLE
CONSTRUCTION MATERIALS WILL EFFECT RADIO RANGE MOUNT IN THREE LOCATIONS 2 & 3
65% - 95% PLACES
ALLOWED
90% - 100% 10% - 70%
OF FULL POWER OF FULL POWER OF FULL POWER
LOCATION 2
ANTENNA NOTES:
LOCATION 1
1. ANTENNA SHOULD BE MOUNTED
AS HIGH AS PRACTICAL.
TERMINAL CONNECTIONS
DXR-702 TERMINALS DXR-702 TERMINALS DXR-702 TERMINALS
COM
COM
COM
COM
COM
COM
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
NOTE: NOTE: NOTE:
LATCHING MODE CHANNEL 2 MUST TRANSMITTERS
ALLOWS PANEL BE EMPTY TO WILL AUTO
TO SHOW DXT-31 REPORT LOW RESTORE AFTER
DOOR STATUS BATTERY 1 SECOND
ALARM PANEL CONNECTION WITH DOOR STATUS ALARM PANEL CONNECTION WITH LOW BATTERY REPORTING ALARM PANEL CONNECTION FOR PANIC BUTTONS
LATCHING RELAY OPTION LATCHING RELAY OPTION 1 SECOND RELAY OPTION
DXR-702 TERMINALS DXR-702 TERMINALS DXR-702 TERMINALS
COM
COM
COM
COM
COM
COM
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
BUZZER
LOAD
EXTERNAL
RELAY 2 STILL
CAMERA
RADIO AUX. POWER POWER
LOAD
POWER POWER SUPPLY SUPPLY CAMERA
XFMR XFMR & VCR
DOOR EXTERNAL
ACCESS CONTROL CONNECTION EXTERNAL RELAY CONNECTION RELAY 1 SECURITY CAMERA CONNECTION
4 SECOND RELAY OPTION STRIKE TOGGLE RELAY OPTION LATCHING RELAY OPTION